AP230 [RFHIC]
MMIC; MMICMMIC
AP230
Product Features
• Small size
Applications
• Satellite
• Repeater
• Base Station
• Converter
• NO matching circuit needed
• High efficiency
• Dual supply voltage
• Higher linearity
• CATV
• Higher productivity
• Lower manufacturing cost
• GaAs MMIC
• SMATV
• 3MHz – 2150MHz
Package : SOIC-8
• -63dBc CSO 135 Channels@ output Level +37dBmV
• -60dBc CTB 135 Channels@ output Level +37dBmV
• -70dBc CSO 8 Channels@ output Level +45dBmV
• -73dBc CTB 8 Channels@ output Level +45dBmV
Descriptions
The power amplifier is designed for base stations and repeater systems.
GaAs MMIC is used and attached on a copper carrier of 8 pin air cavity package with dual supply voltage
Operating Ranges
PARAMETER
Device Voltage
Case Temperature
UNIT
VDC
℃
MIN
TYP
+5
-
MAX
+5.3
+85
-40
Absolute Minimum and Maximum Ratings
PARAMETER
UNIT
VDC
mA
MIN
MAX
+5.5
+320
+10
Device Voltage
Device Current
RF Input Power
dBm
℃
Storage Temperature
-40
+150
Specifications
T=25℃, Vcc=5.0V, 75Ω system
Parameter
Frequency Range
Supply Voltage
Single Ended CATV Evaluation Circuit
Current
Units
MHz
V
M inimum
Typical
3MHz~2.15GHz
5
Maximum
Condition
Vcc=5V
mA
dB
dB
dB
200
220
16
250
S21-Gain
3MHz
50MHz
S21-Gain
15
S21-Gain
14
2150MHz
Reverse ( 3 ~ 200MHz )
S11-Input Return Loss
S22-Output Return Loss
Noise Figure
dB
dB
-16
-16
5.5
OIP3
dBm
dBm
43
+5dBm/2 tone separated by 1MHz
At 100MHz
OIP1
21
Forward ( 50 ~ 870MHz )
S11-Input Return Loss
dB
dB
-11
-11
37
S22-Output Return Loss
OIP3
OIP1
dBm
dBm
dB
+5dBm/2 tone separated by 1MHz
At 800MHz
21
Noise Figure
CSO
4
dBc
dBc
dBc
dBc
dBc
dBc
-63
-60
-55
-70
-73
-70
135 channels,+37dBmV/ch,Single
135 channels,+37dBmV/ch,Single
135 channels,+37dBmV/ch,Single
8 channels,+45dBmV/ch,Single
8 channels,+45dBmV/ch,Single
8 channels,+45dBmV/ch,Single
CTB
XMD
CSO
CTB
50 - 870MHz
3 - 150MHz
XMD
▪ Tel : 82-31-250-5011
▪ rfsales@rfhic.com
▪ All specifications may change without notice.
▪ Version 6.0
MMIC
AP230
Application 1 : Forward (50MHz ~ 2150MHz)
4.7uF/16V
Vcc
Evaluation Board Layout 50-870MHz
100nF
1nF
10nF
RF IN
10nF
560nH
10nF
RF OUT
1.8nH
10nF
AP230
D32212
0.5pF
L1
10nF
10nF
560nH
1nF
100nF
The transformers L1 and L2, used on the RFHIC evaluation board are hand wound
baluns with following spec[L1=3.5turn, ferrite core (Ferronics 12-340-k), L2=3.5 turn,
ferrite core(TDK,L6 RID 3*3*3 H1.2)] was used. φ0.12 1UEW wire was used. An
SMT transformer (D32212,D31766), can also be used.
4.7uF/16V
Vcc
S-Parameters
Noise Figure
6
20
15
10
5
5.5
5
S21
0
4.5
4
-5
S11
S22
-10
-15
-20
-25
-30
3.5
3
2.5
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2
Frequency(GHz)
50
200
400
600
800
1000 1200 1400 1600 1800 2000 2200
Frequency(MHz)
P1dB
OIP3
25
45
40
35
30
25
20
15
10
5
20
15
10
5
0
0
50
200
400
600
800 1000 1200 1400 1600 1800 2000 2200
Frequency(MHz)
50
200
400
600
800 1000 1200 1400 1600 1800 2000 2200
Frequency(MHz)
Level: +37dBmV
FRQ
55.25
Tilt: 135CH FLAT
CTB_RAW
XMD(NCTA)
CTB_COR N-FLR CSU_RAW
CSU_COR
88.1
CSU_FRQ
56
CSL_RAW
68.7
CSL_COR
68.8
CSL_FRQ
54
59.8
69.4
68.7
66.4
66.2
65.6
66.2
66.7
66.2
65.5
65.1
69.5
68.8
66.4
66.2
65.6
66.2
66.8
66.3
65.6
65.3
84.7
85.1
84.9
83.8
82.7
83.4
81.7
82.3
81.4
80.3
83.8
69.3
82.9
80.9
76.9
76.5
74.8
75.4
73.4
72
77.25
109.25
211.25
331.25
445.25
547.25
637.25
745.25
859.25
59.9
60.1
60.4
60.4
61.2
62.9
63.4
64.5
64.8
69.5
87.2
83.9
78.2
77.6
75.7
76.5
74.2
72.8
78
109.99
212.49
332.49
446.5
84.5
69.1
68.7
69.3
71.7
72.5
75.2
76.1
75.8
88.8
69.2
68.8
69.5
72
76.51
107.99
209.99
329.99
443.99
545.98
635.99
743.98
857.99
548.5
73
638.5
76.2
77.5
78
746.49
860.49
▪ Tel : 82-31-250-5011
▪ rfsales@rfhic.com
▪ All specifications may change without notice.
▪ Version 6.0
MMIC
AP230
Application 2 : Reverse (3MHz ~ 200MHz)
4.7uF/16V
Vcc
Evaluation Board Layout 5-200MHz
100pF
1nF
22nF
RF IN
1uF
4.7uH
3.3uF
RF OUT
100pF
1uF
AP230
D31250
R0
3.3uF
10 ohm
22nF
7.5pF
4.7uH
1nF
The transformers L1 and L2, used on the RFHIC evaluation board are hand wound
baluns with following spec[L1=6 turn, ferrite core (TAIYO-YUDEN BF56
1.9*3.4*2.0), L2=3.5 turn, ferrite core(TDK,L6 RID 3*3*3 H1.2)] was used. φ0.12
1UEW wire was used. An SMT transformer (D31044,D31766), can also be used.
100pF
4.7uF/16V
Vcc
S-Parameters
Noise Figure
8
30
20
7
6
5
4
3
S21
10
0
-10
-20
-30
S22
S11
5
0
30
60
90
120
150
180
210
240
270
300
5
50
100
150
200
250
Frequency(MHz)
Frequency(MHz)
P1dB
OIP3
50
45
40
35
30
25
20
15
25
20
15
10
5
0
5
50
100
150
200
250
5
50
100
150
200
250
Frequency(MHz)
Frequency(MHz)
Level: +45dBmV
FRQ XMD(NCTA)
72.2
Tilt: 8CH FLAT
CTB_RAW
79.9
CTB_COR
80.1
N-FLR
93.6
CSU_RAW
92.4
CSU_COR
96.7
CSU_FRQ
7.63
CSL_RAW
71.7
CSL_COR
71.7
CSL_FRQ
5.99
7
31
49
72.8
72.1
78.6
79.8
78.8
80.1
92.1
91.8
78.1
78.2
78.4
78.4
32
76.6
90.5
76.8
94.8
29.99
48.31
49.99
▪ Tel : 82-31-250-5011
▪ rfsales@rfhic.com
▪ All specifications may change without notice.
▪ Version 6.0
MMIC
AP230
ESD Protection
For a safe use in all situations, it is recommended to have proper ESD control techniques while the device is being handled. Here are some
recommended precautions;
- Person at a workbench should be earthed via a wrist strap and a resistor.
- All mains-powered equipment should be connected to the mains via an earth-leakage switch.
- Equipment cases should be grounded.
- Relative humidity should be maintained between 40% and 50%.
- An ionizer is recommended.
- Keep static materials, such as plastic envelopes and plastic trays etc. away from the workbench
Package : SOIC-8 Type
Block Diagram
PIN No
Description
RF IN(2)
RF OUT(1)
RF IN(1)
RF OUT(2)
GND
1
5
1
8
7
6
AMP2
AMP1
4
8
2
3
4
5
2, 3, 6, 7
Exposed slug
GND
Package Dimensions (Type: SOIC-8)
Recommended Pattern
RFHIC Corporation (RFHIC) reserves the right to make changes to any products herein or to discontinue any product at any time without notice. RFHIC do not
assume any liability for the suitability of its products for any particular purpose, and disclaims any and all liability, including without limitation consequential or
incidental damages. The product specifications herein expressed have been carefully checked and are assumed to be reliable. However, RFHIC disclaims liability for
inaccuracies and strongly recommends buyers to verify that the information they are using is current before placing purchase orders. RFHIC products are not
intended for use in life support equipment or application where malfunction of the product can be expected to result in personal injury or death. Buyer uses or sells
such products for any such unintended or unauthorized application, buyer shall indemnify, protect and hold RFHIC and its directors, officers, stockholders,
employees, representatives and distributors harmless against any and all claims arising out of such use. RFHIC’s liability under or arising out of damages, claims of
whatsoever kind and nature which RFHIC products could cause shall be limited in amount to the net purchase price of the products sold to buyer by RFHIC.
▪ Tel : 82-31-250-5011
▪ rfsales@rfhic.com
▪ All specifications may change without notice.
▪ Version 6.0
相关型号:
©2020 ICPDF网 联系我们和版权申明