TDA9615H [NXP]
Audio processor for VHS hi-fi; 音频处理器的VHS您好,科幻型号: | TDA9615H |
厂家: | NXP |
描述: | Audio processor for VHS hi-fi |
文件: | 总44页 (文件大小:266K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
INTEGRATED CIRCUITS
DATA SHEET
TDA9615H
Audio processor for VHS hi-fi
1997 Jun 16
Preliminary specification
File under Integrated Circuits, IC02
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
FEATURES
• All functions controlled via the 2-wire I2C-bus
• Single supply
• Integrated standby modes for low power consumption
• Integrated power muting for line and RFC output
• Full support of video recorder feature modes
• Audio level meter output
GENERAL DESCRIPTION
The TDA9615H is an audio control and processing circuit
for VHS hi-fi video recorders, controlled via the I2C-bus.
The device is adjustment-free using an integrated
auto-calibration circuit. Extensive input and output
selection is offered, including full support for
(Euro-SCART) pay-TV decoding and video recorder
feature modes.
• Hi-fi signal processing:
– Adjustment-free
– High performance
– Patented low distortion switching noise suppressor
– NTSC and PAL (SECAM) standard
• Linear audio input with level adjustment
• 5 stereo inputs and additional mono audio input
• 2 stereo outputs (line and decoder) with independent
output selection
• RF converter output with overload protect AGC.
ORDERING INFORMATION
TYPE
PACKAGE
NUMBER
NAME
DESCRIPTION
VERSION
TDA9615H
QFP44 plastic quad flat package; 44 leads (lead length 1.3 mm);
SOT307-2
body 10 × 10 × 1.75 mm
1997 Jun 16
2
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
BLOCK DIAGRAM
GM4K71
a
1997 Jun 16
3
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
PINNING
SYMBOL
PIN
DESCRIPTION
SYMBOL
PIN
DESCRIPTION
tuner input left
DCREFL
EMPHL
DCL
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
NR DC reference left
TUNL
1
2
NR emphasis left
NR DC decoupling left
NR detector left
TUNR
tuner input right
CINL
3
cinch input left
DETL
AGND
Iref
CINR
4
cinch input right
analog ground
EXT1L
EXT1R
EXT2L
EXT2R
AUXL
5
external 1 input left
external 1 input right
external 2 input left
external 2 input right
auxiliary input left
auxiliary input right
RFC AGC timing input
RFC output
reference current standard
reference voltage filter
NR detector right
NR DC decoupling right
NR emphasis right
NR DC reference right
NR DC feedback right
supply voltage
6
Vref
7
DETR
DCR
8
9
EMPHR
DCREFR
DCFBR
VCC
AUXR
10
11
12
13
14
15
16
17
18
19
20
21
22
RFCAGC
RFCOUT
MUTEC
MUTEL
LINEL
mute for RFC output
mute for line output left
line output left
FMOUT
FMIN
FM output
FM input
V5OUT
ENVOUT
HID
5 V decoupling output
envelope output
LINER
MUTER
DECL
line output right
mute for line output right
decoder output left
decoder output right
linear audio output
linear audio input
NR DC feedback left
HID input
SDA
I2C-bus SDA input/output
I2C-bus SCL input
digital ground
DECR
LINOUT
LININ
SCL
DGND
SAP
tuner SAP input
DCFBL
1997 Jun 16
4
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
1
2
3
4
5
6
7
8
9
33 DCREFR
EMPHR
TUNL
TUNR
CINL
32
31 DCR
CINR
30 DETR
V
I
EXT1L
EXT1R
EXT2L
EXT2R
AUXL
29
28
27
ref
ref
TDA9615H
AGND
26 DETL
25 DCL
AUXR 10
24 EMPHL
23 DCREFL
RFCAGC 11
MGK470
Fig.2 Pin configuration.
FUNCTIONAL DESCRIPTION
An overview of input/output selections is given in Figs 3 to 5.
Full control of the TDA9615H is accomplished via the 2-wire I2C-bus. Up to 400 kbits/s bus speed can be used, in
accordance with the I2C-bus fast-mode specification. The detailed functional description can be found in
Chapter “I2C-bus protocol”.
1997 Jun 16
5
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
GM4K73
o
1997 Jun 16
6
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
GM7K4
f
1997 Jun 16
7
d
decoder select
TUNER
LOH
DECL
DECR
EXT1
SAP
MUTE
TUNL
TUNR
OUTPUT SELECT
input select
output select
0 dB
+1 dB
CINL
CINR
line select
EXT1L
EXT1R
LINEL
LINER
MUTE
EXT2
MUTE
EXT2L
EXT2R
OUTPUT SELECT
SAP
RFC mute
AUXL
AUXR
0 dB AGC
MUTE
RFCOUT
MGK475
a. Active standby mode (STBA = 1, STBP = 0); 75% power reduction.
TUNL
TUNR
input select
CINL
CINR
EXT1L
EXT1R
MUTE
EXT2L
EXT2R
SAP
AUXL
AUXR
b. Passive standby mode (STBP = 1); 90% power reduction.
Fig.5 Input/output selections; standby modes.
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
I2C-BUS PROTOCOL
Addressing and data bytes
For programming the device (write mode) seven data byte registers are available; they are addressable via eight
subaddresses. Automatic subaddress incrementing enables the writing of successive data bytes in one transmission.
During power-on, data byte registers are reset to a default state by use of a Power On Reset (POR) circuit which signal
is derived from the internally generated I2C-bus supply voltage (V5OUT; pin 38). For reading from the device (read mode)
one data byte register is available without subaddressing.
Table 1 TDA9615H addresses and data bytes
DATA BYTE
Write mode
Slave address byte (B8H)
Subaddress bytes (00H to 07H) 0(1)
ADDRESS
1
0
0(1)
1
1
0(1)
1
0
0
0
0
0(1)
SHH
s5
0 or 1
MUTE
NIL2
NS1
LOS
VL2
0 or 1
STBP
NIL1
NS0
DOS
VL1
0 or 1
STBA
NIL0
i0
Control byte (subaddress 00)
Select byte (subaddress 01)
Input byte (subaddress 02)
Output byte (subaddress 03)
AFM
DOC
DOS0
IS2
DETH
s4
NTSC
NIL3
NS2
EOS
VL3
DOS1
i7
IS1
OSR
VL5
IS0
LOH
I7
OSN
VLS
OSL
VL4
RFCM
VL0
Left volume byte
(subaddress 04)
Right volume byte
(subaddress 05)
r7
VRS
VR5
VR4
VR3
VR2
VR1
VR0
p0
Volume byte (subaddress 06)
Power byte (subaddress 07)
simultaneous loading of subaddress 04 and subaddress 05 register
CALS
VCCH
TEST
PORR
p3
p2
p1
Read mode
Slave address byte (B9H)
Read byte
1
0
1
0(2)
1
1
0(2)
0
1(2)
0
0(2)
1
0(2)
CALR
AUTN
POR
Notes
1. Use of subaddress F0H to F7H (1111 0XXX) instead of 00H to 07H (0000 0XXX) disables the automatic subaddress
incrementing allowing continuous writing to a single data byte register.
2. The state of unused read bits are not reliable; their state may change during development.
Table 2 Status of data bytes after POR
DATA BYTE
Control byte
ADDRESS
1
0
0
0
0
1
1
0
0
1(1)
0
1(1)
1
1
0
0
Select byte
0
0(1)
0
0
0
0
0(1)
Input byte
0
0
1
1
1
Output byte
0
0
0
0
0
0
1
Left volume byte
Right volume byte
Power byte
0(1)
0(1)
0
0
0
0
0
0
0
0
0
0
0(1)
0
0(1)
0
0(1)
0
0(1)
0
0
Note
1. For eventual future compatibility it is advised to keep unused write bits equal to POR state.
1997 Jun 16
9
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
Valid transmissions to and from TDA9615H
Table 3 Examples of valid transmissions
FUNCTION
DATA TRANSFER SEQUENCE
Write
START - B8H - 00H - data_for_00 - STOP
Write with auto-increment
Auto-increment ‘wrap-around’
Write without auto-increment
Read
START - B8H - 00H - data_for_00 - data_for_01 - data_for_02 - STOP
START - B8H - 07H - data_for_07 - data_for_00 - data_for_01 - STOP
START - B8H - F6H - data_for_06 - data_for_06 - data_for_06 - STOP
START - B9H - data_from_ic - STOP
START - B9H - data_from_ic - data_from_ic - data_from_ic - STOP
Overview of TDA9615H I2C-bus control
Table 4 Condensed overview
FUNCTION
MODES
CONTROL BITS
Audio FM mode
playback; loop-through(1); record
AFM, DOC and SHH
Dropout cancelling
on; off
DOC
SHH
Headswitch noise cancel
sample-and-hold time
6 µs; 8 µs
Playback hi-fi carrier detection
Record carrier ratio
System standard
Power mute
slow; fast
DETH
0; 6; 8; 9.5; 11; 12.5; 13.5 dB
NTSC(1); PAL
output muting(1)
DOC, SHH and DETH
NTSC
MUTE
Operation mode
Normal input level
Input select
full operation(1); active standby; passive standby
0 (1) to +14 dB; mute
Tuner(1); Cinch; Ext1; Ext2; SAP; Dub Mix; Normal; Aux
STBP and STBA
NIL3 to NIL0
IS2, IS1 and IS0
NS2, NS1 and NS0
Normal select
Input Select; Volume; Input-Left; Volume-Left; SAP;
Tuner; Ext2; mute(1)
Line output amplification
Output select
0 dB(1); +1 dB
LOH
mute(1); Left; Right; Stereo; Normal; Mix-Left; Mix-Right;
Mix-Stereo
OSN, OSR and OSL
Envelope output
Line output select
Decoder output select
RFC output
Output Select(1); Stereo; HF Envelope
Output Select(1); Ext2
Output Select(1); Tuner; Ext1; SAP; mute
0 dB; mute(1)
EOS and AFM
LOS
DOS, DOS1 and DOS0
RFCM
Volume left
−47 to 0 dB(1); 0 to +15 dB; mute
−47 to 0 dB(1); 0 to +15 dB; mute
off(1); start calibration
9 V(1); 12 V
standard operation(1); test modes
VLS, VL5 to VL0
VRS, VR5 to VR0
CALS
Volume right
Auto-calibration
Supply voltage
Test
VCCH
TEST, s4 to NIL0
Note
1. POR.
1997 Jun 16
10
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
Control byte; subaddress 00 (hi-fi and general control)
Table 5 Bits of control byte
BIT
DESCRIPTION
AFM
audio FM mode; see Table 6
dropout cancel; see Table 6
DOC
SHH
sample-and-hold high-state; see Table 6
detector high; see Table 6
DETH
NTSC
MUTE
STBP
STBA
NTSC television system standard; see Table 7
power mute; see Table 8
standby mode passive; see Table 9
standby mode active; see Table 9
Table 6 Bits AFM, DOC, SHH and DETH
AFM DOC SHH DETH MODE
REMARKS
DESCRIPTION
0
0
0
0
X(1)
0
X(1)
X(1)
X(1)
0
X(1) playback(2)
X(1) playback
X(1) playback
X(1) playback
hi-fi circuit in playback mode
no dropout cancelling
DOC off
1
X(1)
DOC on
dropout cancelling active
sample-and-
headswitch noise cancel time is 6 µs
hold time = 6 µs
0
X(1)
1
X(1) playback
sample-and-
headswitch noise cancel time is 8 µs
hold time = 8 µs
0
0
1
1
1
1
1
1
1
1
1
X(1)
X(1)
X(1)
0
X(1)
X(1)
X(1)
0
0
1
playback
playback
detect = fast
detect = slow
hi-fi detector timing: fast mode
hi-fi detector timing: slow mode
X(1) record/loop-through
hi-fi circuit in record/loop-through mode
no FM output signal (EE mode)
0
1
0
1
0
1
0
1
loop-through(3)(4)
0
0
record
0 dB mix
0 dB FM output carrier ratio (1 : 1)
6 dB FM output carrier ratio (1 : 2)
8 dB FM output carrier ratio (1 : 2.5)
standard 9.5 dB FM output carrier ratio (1 : 3)
11 dB FM output carrier ratio (1 : 3.5)
12.5 dB FM output carrier ratio (1 : 4.2)
13.5 dB FM output carrier ratio (1 : 4.7)
0
1
record
6 dB mix
0
1
record
8 dB mix
1
0
record
9.5 dB mix
11 dB mix
12.5 dB mix
13.5 dB mix
1
0
record
1
1
record
1
1
record
Notes
1. X = don’t care.
2. Auto-normal function: if during hi-fi ‘playback’ mode no FM carrier is detected at FMIN (pin 37) the ‘Normal’ mode
audio signal (LININ; pin 21) is automatically selected by the output select function.
a) Hi-fi carrier detection time (i.e. auto-normal release time) can be selected via bit DETH:
‘fast’ mode: 1 to 2 HID periods (33 to 66 ms NTSC, 40 to 80 ms PAL)
‘slow’ mode: 7 to 8 HID periods (233 to 267 ms NTSC, 280 to 320 ms PAL).
b) The status of hi-fi detection can be monitored via the I2C-bus; see bit AUTN of the read byte (see Table 31).
c) If muting is required instead of automatic selection of the ‘Normal’ mode audio signal the normal input level
function should be set to mute; see bits NIL3 to NIL0 of the select byte.
1997 Jun 16
11
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
3. Modes ‘loop-through’ and ‘record’ are equal in audio signal flow; FMOUT (pin 36) however is muted during
‘loop-through’ mode.
4. POR.
Table 7 Bit NTSC
NTSC(1)
MODE
PAL
NTSC(2)
DESCRIPTION
0
1
hi-fi circuit in ‘PAL’ mode (FM carriers: 1.4 and 1.8 MHz)
hi-fi circuit in ‘NTSC’ mode (FM carriers: 1.3 and 1.7 MHz)
Notes
1. Bit NTSC selects between the system standard settings for NTSC and PAL (SECAM) use. The auto-calibration
function uses the system standard HID frequency of 29.97 Hz for NTSC and 25 Hz for PAL. After calibration bit NTSC
allows immediate switching between the NTSC and PAL system standard.
2. POR.
Table 8 Bit MUTE
MUTE(1)
MODE
DESCRIPTION
0
1
−
power mute function released; mute switches open
power mute function activated; mute switches closed
mute(2)
Notes
1. Bit MUTE controls the line and RFC output mute switches at pins 13, 14 and 17 (power mute function). Power mute
is also automatically activated at supply voltage power-up or power-down (VCC; pin 35).
2. POR.
Table 9 Bits STBP and STBA
STBP
STBA
MODE
− (note 1)
DESCRIPTION
0
0
1(4)
0
full operation
1(2)
X(5)
active standby(3)
passive standby(3)
standby mode; reduced power consumption
standby mode; minimum power consumption
Notes
1. POR.
2. By selecting STBA = 1 the TDA9615H is switched to low-power ‘active standby’ mode. To reduce power
consumption most circuits are switched off. RFC, line and decoder outputs however remain active. This way the
direct audio selections offered via the line output select and decoder output select functions (bits LOS and DOS of
the output byte) remain operable in this mode. The ‘Output Select’ mode signal is muted.
3. Calibration and I2C-bus registers are not affected by using ‘active standby’ or ‘passive standby’ mode.
4. By selecting STBP = 1 the TDA9615H is switched to minimum power ‘passive standby’ mode. All circuits except
power mute, I2C-bus and the line input reference buffer (voltage at pins 1 to 10 and 44) are switched off for minimum
power consumption. Use of the power mute function (bit MUTE of control byte) ensures pop-free switching of the line
and RFC output to and from ‘passive standby’ mode. To obtain minimum power consumption the power mute
function should be de-activated again during ‘passive standby’ mode.
5. X = don’t care.
1997 Jun 16
12
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
Select byte; subaddress 01 (decoder output select and linear audio volume control)
Table 10 Bits of select byte
BIT
DESCRIPTION
DOS1
DOS0
NIL3
NIL2
NIL1
NIL0
decoder output select 1; see Table 11
decoder output select 0; see Table 11
normal input level 3; see Table 12
normal input level 2; see Table 12
normal input level 1; see Table 12
normal input level 0; see Table 12
Table 11 Bits DOS1 and DOS0; note 1
DOS1
DOS0
MODE
DESCRIPTION
0
0
1
1
0
1
0
1
Tuner
Ext1
SAP
mute
decoder output signal is TUNL and TUNR input signal
decoder output signal is EXT1L and EXT1R input signal
decoder output signal is SAP input signal
mute
Note
1. By selecting bit DOS = 1 of the output byte several independent signal input selections are offered for the decoder
outputs DECL and DECR (pins 18 and 19) via bits DOS1 and DOS0:
a) TUNL and TUNR inputs (pins 1 and 2)
b) EXT1L and EXT1R inputs (pins 5 and 6)
c) SAP input (pin 44)
d) Mute.
These decoder selections are also operable in ‘active standby’ mode (bit STBA = 1 of the control byte).
1997 Jun 16
13
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
Table 12 Bits NIL3, NIL2, NIL1 and NIL0; note 1
NIL3
NIL2
NIL1
NIL0
DESCRIPTION
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0 dB; note 2
1 dB
2 dB
3 dB
4 dB
5 dB
6 dB
7 dB
8 dB
9 dB
10 dB
11 dB
12 dB
13 dB
14 dB
mute
Notes
1. Mute and 15 settings of amplification can be selected for the linear audio input signal (LININ; pin 21). This level
control can replace the manual adjustment of ‘playback’ mode level at the linear audio circuit.
2. POR.
Input byte; subaddress 02 (input selection for hi-fi and normal audio)
Table 13 Bits of input byte
BIT
DESCRIPTION
IS2
input select 2; see Table 14
input select 1; see Table 14
input select 0; see Table 14
normal select 2; see Table 15
normal select 1; see Table 15
normal select 0; see Table 15
IS1
IS0
NS2
NS1
NS0
1997 Jun 16
14
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
Table 14 Bits IS2, IS1 and IS0; note 1
IS2
IS1
IS0
MODE
Tuner(2)
DESCRIPTION
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
TUNL and TUNR input
CINL and CINR input
Cinch
Ext1
EXT1L and EXT1R input (TV input)
EXT2L and EXT2R input (decoder input)
SAP; mono input
Ext2
SAP
Dub Mix(3)
Normal
Aux
AUX input signal (L) and selection of hi-fi output signal (R)
LININ input (linear audio)
AUXL and AUXR input (e.g. camcorder input)
Notes
1. Bits IS2, IS1 and IS0 select the input signal which is led to the volume controls of the hi-fi processing and generally
via the normal select function to the linear audio circuit (LINOUT; pin 20).
2. POR.
3. ‘Dub Mix’ is a special selection for linear audio use supporting audio dubbing (a video recorder feature mode for
sound recording of linear audio only). ‘Dub Mix’ connects the AUX input signal to the left channel
(1⁄2AUXL + 1⁄2AUXR) and the hi-fi output signal to the right channel (generally 1⁄2hi-fi left + 1⁄2hi-fi right but also
hi-fi left or hi-fi right can be selected). ‘Dub Mix’ also changes part of the ‘Output Select’ mode settings to ‘Normal’
mode for monitoring of the linear audio recording (see control bits OSN, OSR and OSL of the output byte for
‘Dub Mix’ mode input and output selection).
Table 15 Bits NS2, NS1, NS0; note 1
NS2
NS1
NS0
MODE
DESCRIPTION
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
Input Select hi-fi input selection
Volume
hi-fi volume control
left channel of hi-fi input selection only
Input-Left
Volume-Left left channel of hi-fi volume control
SAP
SAP; mono input
TUNL and TUNR input
EXT2L and EXT2R input
mute
Tuner
Ext2
mute(2)
Notes
1. With bits NS2, NS1 and NS0 the input signal is selected which is available at the LINOUT output (pin 20) for
connection to an external linear audio circuit. The signal selected with the input select function (via
bits IS2, IS1 and IS0) is available in the following ways:
a) Left and right channel combined, optional including hi-fi volume control (1⁄2hi-fi left + 1⁄2hi-fi right).
b) Left channel only (language I), optional including left channel volume control.
Furthermore the SAP input (pin 44), tuner input (pins 1 and 2) or EXT2 input (pins 7 and 8) can be selected
independently. Also a mute setting is available.
2. POR.
1997 Jun 16
15
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
Output byte; subaddress 03 (output selection and control)
Table 16 Bits of output byte
BIT
DESCRIPTION
LOH
OSN
OSR
OSL
EOS
LOS
DOS
line output high; see Table 17
output select normal; see Table 18
output select right; see Table 18
output select left; see Table 18
envelope output select; see Table 20
line output select; see Table 21
decoder output select; see Table 22
RFC mute; see Table 23
RFCM
Table 17 Bit LOH; note 1
LOH
MODE
0 dB(2)
1 dB
DESCRIPTION
0
1
no line output amplification
1 dB line output amplification
Notes
1. An additional 1 dB amplification can be selected for line and decoder outputs LINEL, LINER, DECL and DECR
(pins 15, 16, 18 and 19).
2. POR.
Table 18 Bits OSN, OSR and OSL; notes 1 and 2
OSN
OSR
OSL
MODE
mute(3)
DESCRIPTION
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
mute; no selection
Left
left hi-fi channel selected (language I)
Right
right hi-fi channel selected (language II)
hi-fi stereo selected
Stereo
Normal
Mix-Left
Mix-Right
Mix-Stereo
normal selected (linear audio; LININ input)
mix of hi-fi left with normal (1⁄2hi-fi left + 1⁄2normal)
mix of hi-fi right with normal (1⁄2hi-fi right + 1⁄2normal)
mix of hi-fi stereo with normal (1⁄2hi-fi stereo + 1⁄2normal)
Notes
1. When no hi-fi signal is found on tape during ‘playback’ mode the auto-normal function is activated; all output select
function modes except ‘mute’ will be overruled and changed to ‘Normal’ mode. If muting of the hi-fi sound is desired
instead of selecting linear audio the normal input level (bits NIL3 to NIL0 of the select byte) should be set to mute.
Activation of the auto-normal function can be monitored by reading bit AUTN of the read byte.
2. If ‘Dub Mix’ mode is selected via the input select function (see control bits IS2, IS1 and IS0 of the input byte)
functionality of the modes ‘Mix-Left’, ‘Mix-Right’ and ‘Mix-Stereo’ are changed to support audio dubbing input mixing.
Hi-fi channel selection is offered for the input and normal sound is available at the output for monitoring of the linear
audio recording. See also Table 19.
3. POR.
1997 Jun 16
16
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
Table 19 Dub Mix selections
MODE
mute(1)
DUB MIX OUTPUT SELECTION
DUB MIX INPUT SELECTION
mute
mute
Left
left
hi-fi left
Right
right
hi-fi right
Stereo
stereo
normal
normal
normal
normal
1⁄2hi-fi left + 1⁄2hi-fi right
normal
Normal
Mix-Left
Mix-Right
Mix-Stereo
hi-fi left
hi-fi right
1⁄2hi-fi left + 1⁄2hi-fi right
Note
1. POR.
Table 20 Bit EOS
EOS(1)
MODE
DESCRIPTION
0
1
Output Select(2)
Stereo or HF envelope(3)
audio peak envelope of ‘Output Select’ mode signal
audio peak envelope of hi-fi stereo or HF envelope
Notes
1. A signal selection for output ENVOUT (pin 39) is available using bit EOS.
2. POR.
3. The selection made for mode ‘Stereo or HF envelope’ depends upon the mode of the hi-fi processing:
a) Hi-fi ‘loop-through’ mode or ‘record’ mode (bit AFM = 1): audio peak envelope of hi-fi stereo.
b) Hi-fi ‘playback’ mode (bit AFM = 0): HF envelope of left channel FM carrier.
Table 21 Bit LOS; notes 1 and 2
LOS
MODE
DESCRIPTION
0
1
Output Select(3)
Ext2
line output signal is set by output select function
line output signal is EXT2L and EXT2R input
Notes
1. An independent selection of EXT2L and EXT2R inputs (pins 7 and 8) to the line outputs LINEL and LINER
(pins 15 and 16) is possible by setting bit LOS to 1. This direct selection is also operable in ‘active standby’ mode
(STBA = 1 of the control byte).
2. Using bit DOS and bits DOS1 and DOS0 of the output byte mode ‘Tuner’ or ‘Ext1’ selection to the outputs DECL and
DECR (pins 18 and 19) is offered realizing full Euro-SCART pay-TV decoder switching.
3. POR.
1997 Jun 16
17
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
Table 22 Bit DOS; notes 1 and 2
DOS
MODE
Output Select(3) decoder output signal is set by output select function
decoder select(4) decoder output signal is set by decoder output select function
DESCRIPTION
0
1
Notes
1. An independent selection of TUNL and TUNR (pins 1 and 2), EXT1L and EXT1R (pins 5 and 6), SAP (pin 44) or
mute is possible for the decoder outputs DECL and DECR (pins 18 and 19) by setting bit DOS to 1. Source selection
is offered by using bits DOS1 and DOS0 of the select byte. These direct selections are also operable in ‘active
standby’ mode (STBA = 1 of the control byte).
2. In combination with the independent EXT2 selection to the outputs LINEL and LINER (pins 15 and 16) via bit LOS
full Euro-SCART pay-TV decoder switching is offered.
3. POR.
4. Internal mode.
Table 23 Bit RFCM; note 1
RFCM
MODE
DESCRIPTION
RFC output is set by output select function
RFC output signal is muted (AGC reset)
0
1
−
mute(2)
Notes
1. RF converter output RFCOUT (pin 12) can be muted using bit RFCM. During mute the AGC capacitor at pin 11
(RFCAGC) is discharged, resetting AGC control.
2. POR.
1997 Jun 16
18
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
Volume bytes; subaddresses 04, 05 and 06 (left and right channel volume control)
Table 24 Bits of volume bytes; see Table 25
BIT
DESCRIPTION
VLS
VL5
↓
volume left sign
volume left 5
↓
VL0
VRS
VR5
↓
volume left 0
volume right sign
volume right 5
↓
VR0
volume right 0
Table 25 bits VLS, VRS, VL5 to VL0 and VR5 to VR0; note 1
VLS
VRS
VL5
VR5
VL4
VR4
VL3
VR3
VL2
VR2
VL1
VR1
VL0
MODE
VR0
0
0
0
0
0
↓
0
0
0
0
0
0
0
0
0
0
0
1
0 dB
−1 dB
−2 dB
−3 dB
−4 dB
↓
0
0
0
0
1
0
0
0
0
0
1
1
0
0
0
1
0
0
↓
↓
↓
↓
↓
↓
0
0
0
0
0
0
1
1
1
1
1
↓
1
0
1
0
1
1
−43 dB
−44 dB
−45 dB
−46 dB
−47 dB
mute
0 dB(3)
+1 dB
+2 dB
+3 dB
+4 dB
↓
1
0
1
1
0
0
1
0
1
1
0
1
1
0
1
1
1
0
1
0
1
X(2)
1
X(2)
1
X(2)
1
X(2)
1
1
X(2)
X(2)
X(2)
X(2)
X(2)
↓
X(2)
X(2)
X(2)
X(2)
X(2)
↓
0
0
0
0
0
0
0
1
0
0
1
0
0
0
1
1
0
1
0
0
↓
↓
↓
↓
1
1
1
1
1
X(2)
X(2)
X(2)
X(2)
X(2)
X(2)
X(2)
X(2)
X(2)
X(2)
1
0
1
1
+11 dB
+12 dB
+13 dB
+14 dB
+15 dB
1
1
0
0
1
1
0
1
1
1
1
0
1
1
1
1
Notes
1. Left and right volume controls can be set simultaneous by using subaddress 06 (volume byte). Addressing the
volume byte will load both the left and right volume registers with the same data value.
2. X = don’t care.
3. POR.
1997 Jun 16
19
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
Power byte; subaddress 07 (power-up control and test)
Table 26 Bits of power byte
BIT
DESCRIPTION
CALS
VCCH
TEST
PORR
calibration start; see Table 27
CC high; see Table 28
V
test; see Table 29
POR reset; see Table 30
Table 27 Bit CALS; note 1
CALS(2)
MODE
− (note 3)
start calibration start of automatic calibration cycle
DESCRIPTION
0
1
−
Notes
1. Pin 39 (ENVOUT) or bit CALR of the read byte can be monitored to check for successful completion of the calibration.
It is advised to keep CALS logic 1 after calibration to ensure a reliable CALR state.
2. After a change of bit CALS from logic 0 to logic 1, an automatic frequency calibration is performed setting hi-fi
modem, band-pass filter and noise reduction. Use of auto-calibration is only needed after power-up of the supply
voltage (POR).
3. POR.
Table 28 Bit VCCH; notes 1 and 2
VCCH
MODE
9 V; note 3
12 V
DESCRIPTION
0
1
output DC voltage is 4.5 V
output DC voltage is 6 V
Notes
1. To maximize the output drive when using 12 V supply voltage (VCC; pin 35), the DC level of outputs LINEL, LINER,
DECL and DECR (pins 15, 16, 18 and 19) can be changed using bit VCCH.
2. Use of the power mute function (bit MUTE of the control byte) ensures disturbance-free switching of the line output
signal when setting VCCH after power-up.
3. POR.
Table 29 Bit TEST; note 1
TEST
MODE
− (note 2)
test
DESCRIPTION
0
1
standard operation
special measurement test modes
Notes
1. Several special test modes can be selected for testing and evaluation purposes. Bits s4 to NIL0 of the select byte
are used for selection of these tests.
2. POR.
1997 Jun 16
20
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
Table 30 Bit PORR; note 1
PORR
MODE
DESCRIPTION
0
1
− (note 2)
−
POR reset
reset of POR signal bit
Notes
1. Bit POR of the read byte can be used to detect the occurrence of a power-on reset situation (bit POR reads logic 1
in case the I2C register contents equal the POR default state). When applying bit POR this way, PORR should be
used after a power-on reset to force a reset of the POR read bit state to logic 0.
2. POR.
Read byte (device state information)
Table 31 Bits of read byte
BIT
CALR
DESCRIPTION
DESCRIPTION
calibration ready; see Table 32
auto-normal; see Table 33
power-on reset; see Table 34
AUTN
POR
Table 32 Bit CALR; notes 1 and 2
CALR
0
1
device is not calibrated
device has completed auto-calibration
Notes
1. Bit CALR = 0 indicates the device is not calibrated. After an automatic calibration is started by setting bit CALS of the
power byte the end of calibration is signalled by this bit. If for some reason a calibration cannot be completed (e.g.
no HID signal available or hi-fi processing is in ‘playback’ mode) CALR remains logic ‘0’. If calibration is lost due to
a power-on reset situation CALR will return to logic 0 as well.
2. Also the envelope output (pin 39) can be used to check for end of calibration.
Table 33 Bit AUTN; notes 1 and 2
AUTN
DESCRIPTION
0
1
audio FM signal is detected at FM input
no audio FM signal detected; normal sound is selected instead of hi-fi
Notes
1. When hi-fi processing is in ‘playback’ mode but no hi-fi carrier input signal is detected the auto-normal function is
activated. Auto-normal overrules the ‘Output Select’ mode setting, selecting normal sound (i.e. linear audio) instead
of hi-fi. The state of this auto-normal function can be checked via bit AUTN.
2. The auto-normal function is only active (bit AUTN = logic 1) for hi-fi ‘playback’ mode (bit AFM = 0); during ‘record’ or
‘loop-through’ mode bit AUTN is always logic 0.
1997 Jun 16
21
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
Table 34 Bit POR; notes 1 and 2
POR
DESCRIPTION
I2C-bus bit state differs from power-on reset state
I2C-bus bit state equals power-on reset state
0
1
Notes
1. At power-on or during a power voltage dip, an internal power-on reset signal is generated which resets the I2C-bus
data bits to a predefined state. When the internal data bits are found to be in POR state (due to an actual power-on
reset but also if set via the I2C-bus) bit POR signals logic 1.
2. Using the POR bit to detect the occurrence of a power-on reset requires bit PORR to be set logic 1 after power-up.
Setting bit PORR forces the POR bit to logic 0 independent of other I2C-bus bit settings. After calibration is completed
also the CALR bit can be used to detect a power-on reset; calibration will be lost in such situation which is signalled
by CALR = 0.
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 134).
SYMBOL
VCC
PARAMETER
MIN.
MAX.
13.2
UNIT
supply voltage
0
V
Tstg
Tamb
Ves
storage temperature
−65
+150
70
°C
°C
operating ambient temperature
electrostatic handling
machine model
0
−300
+300
V
V
human body model
−3000
+3000
THERMAL CHARACTERISTICS
SYMBOL
Rth j-a
PARAMETER
CONDITIONS
CONDITIONS
VALUE
60
UNIT
thermal resistance from junction to ambient in free air
K/W
DC CHARACTERISTICS
SYMBOL
PARAMETER
MIN. TYP. MAX. UNIT
Supply voltage
VCC
supply voltage; pin 35
VCCH = 0
8.1
8.1
9
13.2
13.2
V
V
VCCH = 1
12
Supply current
ICC
supply current; pin 35
−
−
45
12
60
18
mA
mA
STBA = 1
(‘active standby’ mode)
STBP = 1
−
4
6
mA
(‘passive standby’ mode)
1997 Jun 16
22
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
SYMBOL
PARAMETER
CONDITIONS
MIN. TYP. MAX. UNIT
Input voltages (internally generated)
VI
input voltage
pins 1 to 10, 21 and 44
pin 37
−
−
3.8
1.9
−
−
V
V
Output voltages
VO
output voltage
pin 12
−
−
−
−
−
−
3.8
4.5
6
−
−
−
−
−
−
V
V
V
V
V
V
pins 15, 16, 18 and 19
VCCH = 0
VCCH = 1
pin 20
pin 36
pin 38
4.5
1.2
5
Output current
IO
output current at pin 38
−
−
3
mA
HID input; pin 40
VIH
VIL
HIGH-level input voltage
LOW-level input voltage
2.75
0
−
−
5.5
V
V
2.25
AC CHARACTERISTICS
Loop-through mode
Audio input level −8 dBV for f = 1 kHz at TUN inputs (pins 1 and 2); VCC = 12 V; Tamb = 25 °C; POR state with mute off;
calibrated; bit NTSC set to logic 1 or logic 0; measured in application diagram of Fig.6; unless otherwise specified.
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Line inputs and linear audio input (TUN, CIN, EXT1, EXT2, AUX, SAP and LININ; pins 1 to 10, 44 and 21)
Ri
Vi
input impedance
input voltage
100
130
−
kΩ
−
−
9
dBV
Line and decoder outputs (LINEL, LINER, DECL, DECR; pins 15, 16, 18 and 19)
Vo
output voltage
−9
−8
7
−8
−7
−6
−
dBV
dBV
dBV
dBV
%
LOH = 1 (+1 dB output signal)
note 1
−7
Vo(max)
maximum output voltage
8
note 1; VCCH = 1; VCC = 12 V
10
−
11
−
THD
αcb
total harmonic distortion
channel balance
noise level
0.01
0
0.1
+1
−90
150
−70
−1
−
dB
Vn
TUN = −∞ dBV; note 2
−94
100
−95
dBV
Ω
Ro
output impedance
volume mute
−
αmute
VLS to VL0 and
−
dB
VRS to VR0 = mute
output mute
OSN, OSR and OSL = mute
−
−85
−70
dB
1997 Jun 16
23
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
−83
MAX.
UNIT
dB
αct(ch)
crosstalk between channels
channel crosstalk TUNL or
−
−70
TUNR = −∞ dBV
αct(ch)(i)
Io(max)
Io
crosstalk between input channels note 3
−
−
−
−93
+1
−
−
−
dB
output current limiting
MUTE = 1; power mute
STBP = 1; passive standby
mA
mA
discharge output current
−1
Linear audio output (LINOUT; pin 20)
Vo
Ro
output voltage
−9
−8
−7
dBV
output impedance
−
200
300
Ω
RF converter output (RFCOUT; pin 12)
Vo
output voltage
−9
−4.5
−
−8
−7
−1.5
−
dBV
dBV
%
output voltage at high level
total harmonic distortion
TUN = +8 dBV
−3
THD
0.03
<0.2
−80
200
+1
TUN = up to +8 dBV
−
−
%
Vn
noise level
TUN = −∞ dBV; note 2
−
−
dBV
Ω
Ro
output impedance
output current limiting
discharge output current
−
300
−
Io(max)
Io
MUTE = 1; power mute
−
mA
mA
STBP = 1; passive standby
−
−1
−
Power mute outputs (MUTEC, MUTEL, MUTER; pins 13, 14 and 17)
Ro output impedance
50
100
15
−
−
kΩ
MUTE = 1; DC load = ±1 mA
Envelope output (ENVOUT; pin 39); audio peak envelope
−
Ω
Vo
output voltage
1.69
−
1.8
−
1.91
0.3
V
V
V
output voltage at zero level
TUN = −∞ dBV
output voltage at zero level;
maximum volume
TUN = −∞ dBV;
volume = +15 dB
−
−
0.35
output voltage at high level
channel balance
TUN = +8 dBV
4.0
−0.11
−
4.5
0
5.0
V
αcb
+0.11
1.5
V
Ro
output impedance
1
kΩ
Notes
1. THD = 1%; output load: RL = 5 kΩ; CL = 2.2 nF; volume = +3 dB (12 V); TUN level varied.
2. Typical value: B = 20 Hz to 20 kHz, ‘unweighted’; production testing: B = 300 Hz to 20 kHz, ‘unweighted’.
3. Crosstalk of any line input pair (TUN, CIN, EXT1, EXT2, AUX or SAP) to any other line input.
1997 Jun 16
24
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
Record mode
For test modes see Table 38.
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Noise reduction (test 25: LINEL and LINER; pins 15 and 16)
THD
total harmonic distortion
−
−
0.1
0.3
1
%
at high level; TUN = +8 dBV
0.2
0
%
αcb
αlin
channel balance
linearity
−1
+1
dB
TUN = −8 to −68 dBV
−31.5 −30.2 −28.5 dB
high-level linearity
TUN = −8 to +8 dBV
7.5
8
8.5
dB
dB
αn
noise level with respect to output
signal
TUN = −8 to = −∞ dBV; note 1
−
−46
−41
tatt
attack time
in accordance with VHS
specification
−
5
−
ms
ms
dB
dB
dB
trec
fres
recovery time
−
70
−
frequency response 300 Hz
frequency response 10 kHz
TUN = 1 kHz to 300 Hz
TUN = 1 kHz to 10 kHz
−0.7
3.1
−0.2
3.9
−0.1
+0.3
4.7
+0.5
audio low-pass filter response
20 kHz
TUN = 1 kHz to 20 kHz; test 26 −0.5
audio low-pass filter response
60 kHz
TUN = 1 kHz to 60 kHz; test 26
−
−24
−12
dB
FM modulator (test 25, test 26 and no test: FMOUT; pin 36)
THD
total harmonic distortion
∆f = 50 kHz
−
0.1
150
0
0.2
160
+5
%
∆f(max)
fc(error)
∆fc(l-r)
maximum FM frequency deviation
carrier frequency error
140
−5
kHz
kHz
after calibration
carrier frequency difference
between left and right channel
fc(r) − fc(l) after NTSC calibration 399.2 401.2 403.2 kHz
∆fc
carrier frequency shift
temperature coefficient
NTSC/PAL system switching
97
100
103
kHz
TC
−
±50
−
ppm/K
Noise reduction and FM modulator (FMOUT; pin 36)
∆f FM deviation
HF output (FMOUT; pin 36)
Vo(rms) output voltage left carrier
44.5
50
56.1
kHz
1st harmonic (RMS value)
1st harmonic (RMS value)
53
60
68
mV
mV
output voltage right carrier
160
2.7
180
3.0
202
3.3
Vo(l)/Vo(r)
output voltage ratio between left
and right carrier
D3H
Ro
distortion (3rd harmonic)
output impedance
3rd harmonic/1st harmonic
−
−
−28
−18
dB
100
150
Ω
Note
1. Typical value: B = 20 Hz to 20 kHz, ‘unweighted’; production testing: B = 300 Hz to 20 kHz, ‘unweighted’.
1997 Jun 16
25
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
Playback mode
VFMIN(rms) = 30 mV (RMS value); ∆f = 50 kHz; fmod = 1 kHz; f = f0; VCC = 12 V; Tamb = 25 °C; bit NTSC set to logic 1 or
logic 0; measured in application diagram of Fig.6; unless otherwise specified. For test modes see Table 38.
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX.
FMIN; pin 37 and HF AGC (test 5 and test 6: FMOUT; pin 36)
UNIT
Vi(p-p)
input voltage level
left plus right channel; note 1
−
0.17
2
V
(peak-to-peak value)
AGC start level (at pin 37)
control bandwidth
left plus right channel
note 2
59
84
10
118
mV
B
−
−
kHz
Left channel band-pass filter (test 3: FMOUT; pin 36)
Vo
band-pass filter output voltage
f = f0; VFMIN(rms) = 30 mV
(RMS value)
105
150
215
mV
dB
Vo1/Vo
−
−30
−20
band-pass filter output voltage
ratio
f0 – 400 kHz
-------------------------------
f0
Vo2/Vo
Vo3/Vo
Vo4/Vo
Vo5/Vo
Vo6/Vo
Rd(g)
−9
−9
−
−6
−
dB
dB
dB
dB
dB
µs
f 0 – 150 kHz
--------------------------------
f0
−5
−
f 0 + 150 kHz
--------------------------------
f0
−17
−12
−
−12
−9
−30
−
f 0 + 250 kHz
--------------------------------
f0
−
f 0 + 250 kHz
--------------------------------
f0 + 150 kHz
−
f 0 + 400 kHz
--------------------------------
f0
group delay ripple
f0 − 150 kHz to f0 + 150 kHz
−
<0.5
1997 Jun 16
26
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Right channel band-pass filter (test 4: FMOUT; pin 36)
Vo
band-pass filter output voltage
f = f0; VFMIN(rms) = 30 mV
(RMS value)
105
150
215
mV
Vo1/Vo
−
−
−30
dB
dB
dB
dB
dB
dB
µs
band-pass filter output voltage
ratio
f0 – 400 kHz
-------------------------------
f0
Vo2/Vo
Vo3/Vo
Vo4/Vo
Vo5/Vo
Vo6/Vo
Rd(g)
−
−17
−5
−10
−
f 0 – 250 kHz
--------------------------------
f0
−9
−
f 0 – 150 kHz
--------------------------------
f0
−12
−6
−9
−
f 0 – 250 kHz
--------------------------------
f0 – 150 kHz
−9
−
f 0 + 150 kHz
--------------------------------
f0
−30
<0.5
−20
−
f 0 + 400 kHz
--------------------------------
f0
group delay ripple
f0 − 150 kHz to f0 + 150 kHz
−
Hi-fi detector and dropout cancelling
Vi(A)
AUTN activation level
left channel carrier at FMIN
(RMS value)
3.0
4.2
5.8
mV
dB
Vi(D)/Vi(A)
DOC level with respect to AUTN
level
left channel carrier at FMIN
−7
−4
−2
td(A)
td(D)
AUTN activation delay
DOC switch-off delay
carrier to no carrier at FMIN
no carrier to carrier at FMIN
200
5
300
9
500
14
µs
µs
Head switching noise suppressor (test 25: LINEL and LINER; pins 15 and 16)
th
hold pulse length
5
7
−
6
8
−
7
µs
µs
dB
SHH = 1
note 3
9
THD
td
total harmonic distortion (audio
signal)
−73
delay from HID to hold
−
0.3
−
µs
Envelope output (ENVOUT; pin 39)
Vo
output voltage
FMIN = 2 mV (RMS value);
left channel
0.6
2.5
4.2
0.9
2.9
4.7
1.2
3.3
5.0
V
V
V
FMIN = 20 mV (RMS value);
left channel
FMIN = 200 mV (RMS value);
left channel
1997 Jun 16
27
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
PLL FM demodulator (test 25: LINEL and LINER; pins 15 and 16)
Vi
sensitivity
∆f = 150 kHz; S/N = 35 dB
∆f = 50 kHz
−
−
−
0.3
1.2
0.3
1.5
mV
THD
total harmonic distortion
0.03
0.2
%
%
total harmonic distortion at
maximum
∆f = 150 kHz
S/N
signal to noise ratio
channel crosstalk
∆f = 50 to 0 kHz
54
60
−
−
dB
dB
αct(ch)
left or right carrier ∆f = 0 kHz
−
−80
Noise reduction (test 26: LINEL and LINER; pins 15 and 16)
Vn
noise level
TUN = −∞ dBV; note 4
TUN = −3.5 dBV
−
−96
−90
0.2
dBV
%
THD
αl
total harmonic distortion
linearity
−
0.05
59.6
+0.4
−7.7
TUN = −3.5 to −33.5 dBV
TUN = 1 kHz to 300 Hz
TUN = 1 kHz to 10 kHz
58
62
dB
dB
dB
fres
frequency response 300 Hz
frequency response 10 kHz
−0.6
−9.2
+1.4
−6.2
FM demodulator and noise reduction (LINEL and LINER; pins 15 and 16)
Vo
output voltage
−10
−8
−6
dBV
dB
αcb
channel balance
−1.5
0
+1.5
Notes
1. Signals below maximum input level are handled without internal clipping. Higher input levels however can still be
handled properly by the demodulators. Typical input level equals two carriers of 30 mV (RMS value).
2. Single carrier signal at FMIN of 75 mV (RMS value) and amplitude modulated. Control bandwidth is the modulation
frequency at which the amplitude modulation is attenuated 3 dB by the HF AGC.
3. Sample-and-hold audio distortion is measured using 500 Hz at HID input (pin 40). FMIN: fmod = 10 kHz; ∆f = 50 kHz.
Audio distortion is measured using a 3 kHz 4th order low-pass filter. Value is corrected with 24 dB in order to
calculate equivalent distortion at 30 Hz HID input.
4. Typical value: B = 20 Hz to 20 kHz, unweighted; production testing: B = 300 Hz to 20 kHz, unweighted.
1997 Jun 16
28
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
APPLICATION AND TEST INFORMATION
GM4K72
a
1997 Jun 16
29
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
approximately 401.2 kHz. This value effectively reduces
the crosstalk from hi-fi carriers to the video colour signal as
present during ‘playback’ mode using Extended Play (EP)
tape speed.
Automatic calibration; see Fig.7
By means of bit CALS (power byte) the integrated
auto-calibration system is activated. By adjusting the
carrier frequencies, band-pass filters and noise reduction
filters auto-calibration ensures that the hi-fi processing
always is in accordance with the VHS hi-fi system
standard. Calibration is only needed after start-up of the
video recorder; as long as the supply voltage (pin 35) is
available calibration settings remain stable.
NTSC calibration uses the standard 29.97 Hz (i.e.
16.683 ms) HID signal where PAL calibration uses the
standard 25 Hz (i.e. 20 ms) HID signal. The maximum
frequency error after auto-calibration is ±5 kHz assuming
a HID HIGH-time error of maximum 5 µs. To realize NTSC
EP optimization within ±2 kHz, HID jitter should not exceed
1 µs. In general the crystal based HID signal available in
the video recorder can be used without modification.
Auto-calibration is performed with the device in hi-fi
‘loop-through’ mode, no standby or test mode should be
active (auto-calibration demands bit settings AFM = 1,
STBP = 0, STBA = 0 and TEST = 0). After setting bit
CALS (power byte) to logic 1 auto-calibration is started.
Calibration is performed fully automatically, using the HID
input signal as a reference.
After calibration of the oscillators, the band-pass filters are
calibrated together with the integrated ‘weighting’ and
‘FM de-emphasis’ filter of the noise reduction. The total
auto-calibration time needed is 17 HID cycles or less.
End of calibration is signalled by bit CALR of the read byte.
Calibration of the oscillator frequencies is performed by
measuring the number of oscillator cycles within one HID
HIGH period and comparing this with an internal value
stored in ROM. Four different ROM values are available for
NTSC or PAL (SECAM) system calibration of both the left
and right channel carrier.
The envelope output can also be used to monitor
calibration; for this purpose ENVOUT (pin 39) is forced
>2.5 V during calibration. The audio signal to the audio
envelope (level meter) function should be muted;
otherwise the audio envelope output may be >2.5 V as
well making it impossible to detect end of calibration via
the ENVOUT pin.
In case of NTSC calibration a special routine is active for
the right channel carrier calibration resulting in a frequency
difference between the left and right channel carrier of
2
I C-bus write (CALS)
logic 0
logic 1
pin 40
(HID)
left channel oscillator
right channel oscillator
band-pass and
noise reduction filters
logic 0 logic 1
2
I C-bus read (CALR)
pin 39
(ENVOUT)
5 V
3 V
4 V
calibration
ready
MGK477
Fig.7 Example of automatic calibration flow.
30
1997 Jun 16
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
After a calibration in ‘NTSC’ or ‘PAL’ mode the oscillators
and band-pass filters can be switched between NTSC and
PAL system frequencies without the need for additional
calibration. Switching between these system modes is
executed immediately and can be done in any operational
mode. Frequency accuracy of switching is 100 kHz ±3 kHz
for both carriers. For ‘record’ mode however it is advised
to use re-calibration after system switching; this to obtain
the best possible frequency accuracy. A new
carrier level (e.g. auto-tracking). At the microcontroller only
one A/D converter input is needed for reading of all
necessary information. During ‘playback’ mode I2C-bus
bit EOS offers selection between audio or carrier level
information. Audio level information is always output
during ‘loop-through’ mode and ‘record’ mode however
now EOS offers a fixed selection of hi-fi stereo (i.e.
independent of the ‘Output Select’ mode setting); helpful
when audio level information is used by the microcontroller
for controlling the hi-fi record volume.
auto-calibration can be started by first resetting bit CALS
to logic 0 followed by setting bit CALS to logic 1 again.
Envelope output; see Figs 8 to 11
ENVOUT (pin 39) is an analog output for stereo audio level
(e.g. level meter display) and for ‘playback’ mode FM
Table 35 Envelope output select
AFM
EOS
ENVELOPE OUTPUT
FUNCTIONAL USE
level meter display
0 (playback mode)
0 (playback mode)
0
1
0
AF envelope of output select
HF envelope
auto-tracking or manual tracking display
level meter display
1 (record mode/
AF envelope of output select
loop-through mode)
1 (record mode/
1
AF envelope of hi-fi stereo
record volume control (and level display)
loop-through mode)
Audio envelope uses time multiplexing to output both left
and right channel audio level. A peak hold function and
dynamic range compression (square root function) are
included for easy read-out. The peak hold function as well
as left and right channel multiplexing is controlled by the
HID input signal (pin 40).
The HF envelope output signal is continuous and derived
from the left channel carrier. HF envelope shows a
logarithmic characteristic.
1997 Jun 16
31
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
2
I C-bus
EOS = 0 or AFM = 1
EOS = 1 and
AFM = 0
registers
HID input
0
1
2
3
HID period
peak right
in period -1
peak right
in period 1
peak right
in period 0
peak right
in period 2
peak left
in period 3
envelope out
peak left
in period 1
peak left
in period 0
HF envelope
peak left
in period 2
MGK478
Fig.8 Timing diagram of envelope output signal.
HID
(pin 40)
left channel audio:
output select
SAMPLE
RESET
FULL WAVE
RECTIFIER
SQUARE ROOT
COMPRESSION
SAMPLE-
AND-HOLD
PEAK HOLD
hi-fi
right channel audio:
output select
ENVOUT
(pin 39)
SAMPLE
RESET
FULL WAVE
RECTIFIER
SQUARE ROOT
COMPRESSION
AF
envelope
SAMPLE-
AND-HOLD
PEAK HOLD
hi-fi
EOS • AFM
HF
EOS • AFM
envelope
1.3/1.4 MHz carrier
HF LEVEL DETECTOR
MGK480
Fig.9 Functional diagram of envelope output circuit.
32
1997 Jun 16
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
MGK481
5
handbook, halfpage
ENVOUT
output
voltage
(V)
4
3
2
1
0
−40
−30
−20
−10
0
10
LINE output level (dBV)
LOH = 0.
Fig.10 Envelope output; AF envelope (audio peak level).
MGK482
5
handbook, halfpage
ENVOUT
output
voltage
(V)
4
3
2
1
0
−1
2
3
10
1
10
10
10
FMOUT left channel carrier amplitude (RMS value) (V)
NTSC (1.3 MHz) or PAL (1.4 MHz).
Fig.11 Envelope output; HF envelope (playback carrier level).
33
1997 Jun 16
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
After the output DC voltage is settled the power mute
function can be deactivated by selecting MUTE = 0.
Now the mute switches are opened showing a high
impedance of 100 kΩ to ground and output current limiting
is deactivated. Note that the time needed for output DC
settling is proportional to the output capacitor value used;
with a 10 µF capacitor a safe mute time to use is 200 ms
(i.e. tmute = C × 20000). Using such controlled muting very
good performance is achieved for power-up, power-down
and ‘passive standby’ mode switching.
Power mute; see Fig.12
Without countermeasures switching of the power supply
voltage (VCC; pin 35) or use of the built-in ‘passive
standby’ mode causes strong disturbances on the output
pins because of the rise or drop of the output’s DC
voltages. The TDA9615H includes three integrated mute
switches to block such disturbances and avoiding the need
of an external mute circuit. By connecting the power mute
switches behind the line and RFC output capacitors
pop-free line and RFC output signals are realized.
At a sudden supply power loss however (e.g. mains power
plug pulled) there may be no time to activate the power
mute function via the I2C-bus. A power-down detector
however instantly activates the power mute function in
case the supply voltage falls below 7 V (auto-mute).
For proper muting supply voltage drop rate should not
exceed 1 V/10 ms.
Power muting is active when control byte bit MUTE = 1.
Because this also is the POR default state, muting is
automatically activated when the power supply voltage is
switched on. The integrated mute switches (MUTEC,
MUTEL and MUTER; pins 13, 14 and 17) are closed,
forming a low impedance path to ground. Furthermore the
line and RFC outputs (RFCOUT, LINEL and LINER;
pins 12, 15 and 16) are current limited to 1 mA to achieve
good attenuation without the need for a series resistor
between output and mute switch. Although the decoder
outputs (DECL and DECR; pins 18 and 19) have no
integrated muting these are current limited also for use
with the integrated mute switches or to assist possible
external muting.
V
CC
auto-mute
(V
< 7 V)
CC
(1)
(1)
bit MUTE
bit STBP
pins 12, 15 and 16
output signal
with power mute
pins 13, 14 and 17
auto-mute
power
off
active
operation
passive
standby
active
operation
power off
(standby)
active
operation
power
off
t
t
t
t
t
mute
MGK476
mute
mute
mute
mute
(1) POR.
Fig.12 Example of power mute control and auto-mute function.
34
1997 Jun 16
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
Do not set MUTE and change STBP at the same time;
to avoid output glitches power muting should precede the
switching of ‘passive standby’ mode. Power muting takes
up approximately 4 mA supply current, so to realize the
minimum power consumption of ‘passive standby’ mode
muting has to be deactivated. Note also the use of ‘passive
standby’ mode to initiate a controlled power-off switching.
The external resistor should have the following
dimensions: value = 39.0 kΩ ±2%; temperature
coefficient = ±50 ppm/K.
Standard hi-fi audio level
Using the application circuit as proposed in Fig.6, the
standard FM deviation of 50 kHz equals a 1 kHz audio
signal of −8 dBV line output level (LOH = 0). A different
standard audio level can be selected by changing the
external filter components of the noise reduction at
pins 24 and 32 (EMPHL and EMPHR); standard audio
level changes proportional to the impedance of the
external de-emphasis filter; see Table 36.
Iref resistor
The external resistor at pin 28 defines internal reference
currents and determines temperature stability of the
circuits adjusted by the auto-calibration function.
Table 36 Standard audio levels; see application diagram of Fig.6
COMPONENT VALUES
LINE OUTPUT LEVEL FOR 50 kHz FM DEVIATION
(EQUIVALENT TO 1 kHz AUDIO SIGNAL) (dBV)
R1 (kΩ)
R2 (kΩ)
C1 (nF)
91
82
75
68
62
56
51
7.5
6.8
6.2
5.6
5.1
4.7
4.3
2.4
2.7
3.0
3.3
3.6
3.9
4.3
−5.6
−6.4
−7.1
−8.0
−8.8
−9.8
−10.6
RFC AGC; see Fig.13
To avoid over modulation in the RF converter unit connected to RFCOUT (pin 12) an AGC function is incorporated,
limiting the maximum signal level at pin RFCOUT to −3 dBV.
MGK479
handbook, halfpage
RFC output
(dBV)
−3
−3
line output (dBV)
Fig.13 RF converter output AGC.
1997 Jun 16
35
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
The RFC output can be muted by setting of bit RFCM = 1.
When applying this mute the AGC control is reset by
discharging the capacitor at pin 11 (RFCAGC).
INPUT MIX
A new, complete, recording is made on the linear audio
track; afterwards ‘playback’ mode uses linear audio sound
only. This way hi-fi stereo quality is lost but there is total
freedom in defining the new material. Furthermore this
way ‘playback’ mode is no longer restricted to hi-fi video
recorders with output mix option.
Audio dubbing
TDA9615H includes unparalleled functionality supporting
the audio dubbing function of hi-fi video recorders. Audio
dubbing is a feature mode for recording of new sound
material on the linear audio track (i.e. normal sound) of an
existing recording. Audio dubbing can be used in two
different ways.
Selection ‘Dub Mix’ mode of the input select function,
when combined with selection ‘Volume’ mode of the
normal select function, changes the circuit into a mixing
desk. A new linear audio recording can be created mixing
together new and original sound. By use of the left and
right channel volume controls continuous control is offered
over amplitude and ratio mix of the AUX input signal (e.g.
a microphone input) and the original hi-fi ‘playback’ mode
sound.
OUTPUT MIX
A new, partly, recording is made on the linear audio track;
afterwards during ‘playback’ mode the new linear audio
and the original hi-fi sound are combined. This way
hi-fi stereo quality remains and linear audio is only partly
used e.g. for speech only (commentary track). However
there is no control over the original (hi-fi) sound.
This functionality is realized by internal connection of the
AUX input pair to the left channel volume control and by
internal connection of the hi-fi output signal pair to the right
channel volume control. For output and hi-fi selection the
‘Dub Mix’ mode uses, and partly overrules, the output
select function settings. Output select function modes
‘Mix-Left’, ‘Mix-Right’ and ‘Mix-Stereo’ make the normal
sound available at the line outputs for monitoring of the
‘Dub Mix’ mode recording.
‘Playback’ mode mixing of hi-fi and normal sound is
supported by the output select function modes ‘Mix-Left’,
‘Mix-Right’ and ‘Mix-Stereo’ (OSN, OSR and OSL of the
output byte) creating a fixed output signal of
1⁄2hi-fi left + 1⁄2normal.
Table 37 Input select function is set to ‘Dub Mix’ mode (IS2, IS1, IS0 = 101); note 1
DUB MIX INPUT SELECTION
OUTPUT SELECT
MODE
DUB MIX OUTPUT
SELECTION
OSN
OSR
OSL
LEFT CHANNEL RIGHT CHANNEL
Mute
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
mute
aux stereo
aux stereo
aux stereo
aux stereo
aux stereo
aux stereo
aux stereo
aux stereo
mute
Left
hi-fi left
hi-fi right
stereo
hi-fi left
hi-fi right
stereo
Right
Stereo
Normal
Mix-Left
Mix-Right
Mix-Stereo
normal
normal
normal
normal
normal
hi-fi left
hi-fi right
hi-fi stereo
Note
1. Modes shown in bold are the most used modes.
Output select function mode ‘Mix-Stereo’ is the setting
generally used for audio dubbing. In combination with
setting the normal select function to ‘Volume’ mode user
control over amplitude and ratio is offered for the AUX and
hi-fi signal as follows: (1⁄4AUXL + 1⁄4AUXR) × volume left +
(1⁄4hi-fi left + 1⁄4hi-fi right) × volume right.
Switching hi-fi to a mode other than ‘playback’ or selection
of output select function mode ‘Normal’ should be avoided;
using these settings a signal loop can be closed from
output to input possibly leading to audio oscillation. For the
same reason auto-normal switching is not active during
‘Dub Mix’ mode; in case no hi-fi input signal is detected the
hi-fi sound is muted.
1997 Jun 16
36
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
Test modes; see Table 38
Special test modes are implemented for testing and evaluation purposes. These test modes are available via the power
byte TEST bit and selection is enabled via bits of the select byte.
Table 38 Test modes for evaluation purposes
TEST
s4
X(1)
NIL3
X(1)
NIL2
X(1)
NIL1
X(1)
NIL0
X(1)
DESCRIPTION
standard operation
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
0
1
1
0
0
1
1
0
1
0
1
0
test 1: left channel FM carrier only (1.3 or 1.4 MHz);
record mode
1
1
1
1
1
test 2: right channel FM carrier only (1.7 or
1.8 MHz); record mode
test 3: left channel band-pass filter, HF AGC off;
playback mode (test output = FMOUT)
test 4: right channel band-pass filter, HF AGC off;
playback mode (test output = FMOUT)
test 5: HF AGC (via left channel band-pass filter);
playback mode (test output = FMOUT)
test 6: HF AGC (via right channel band-pass filter);
playback mode (test output = FMOUT)
100111 to 111000
product testing; not for evaluation; note 2
test 25 (note 3)
1
1
1
0
0
1
a: left channel FM modulator (left carrier only);
record mode (test input = line in left)
b: left and right channel noise reduction
(compressor); record mode (test output = line out)
c: left and right channel FM demodulator; playback
mode (test output = line out)
1
1
1
0
1
0
test 26 (note 3)
a: right channel FM modulator (right carrier only);
record mode (test input = line in right)
b: left and right channel audio low-pass filter;
record mode (test input = line in, test output = line
out)
c: left and right channel noise reduction
(expander); playback mode (test input = line in);
note 4
Notes
1. X = don’t care.
2. Calibration may be lost when selecting product testing modes.
3. Audio output level for tests 25b and 25c (test output = line out) is typical −6.5 dBV (with input = −8 dBV or FM
deviation = 50 kHz; LOH = 0). Audio input level for tests 25a, 26a and 26c (test input = line in) is typical −6.5 dBV
(for output = −8 dBV or FM deviation = 50 kHz; hi-fi volume = −3 dB). The test outputs and test inputs used for
tests 25 and 26 directly connect to internal signal lines. Signals found here are not compensated for temperature or
tolerance spread, level measurements therefore can be used relative only. Absolute values are no indication of
overall performance.
4. Test 26c (expander test) requires the auto-normal function to be deactivated (i.e. carrier available at FMIN pin).
1997 Jun 16
37
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
PACKAGE OUTLINE
QFP44: plastic quad flat package; 44 leads (lead length 1.3 mm); body 10 x 10 x 1.75 mm
SOT307-2
y
X
A
33
23
34
22
Z
E
e
Q
H
E
E
A
2
A
(A )
3
A
1
w M
θ
b
p
L
p
pin 1 index
L
12
44
detail X
1
11
w M
Z
v
M
A
D
b
p
e
D
B
H
v
M
B
D
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
A
(1)
(1)
(1)
(1)
UNIT
A
A
A
b
c
D
E
e
H
D
H
L
L
Q
v
w
y
Z
Z
E
θ
1
2
3
p
E
p
D
max.
10o
0o
0.25 1.85
0.05 1.65
0.40 0.25 10.1 10.1
0.20 0.14 9.9 9.9
12.9 12.9
12.3 12.3
0.95 0.85
0.55 0.75
1.2
0.8
1.2
0.8
mm
2.10
0.25
0.8
1.3
0.15 0.15 0.1
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
EIAJ
92-11-17
95-02-04
SOT307-2
1997 Jun 16
38
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
SOLDERING
Introduction
Wave soldering
Wave soldering is not recommended for QFP packages.
This is because of the likelihood of solder bridging due to
closely-spaced leads and the possibility of incomplete
solder penetration in multi-lead devices.
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
If wave soldering cannot be avoided, the following
conditions must be observed:
• A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave)
soldering technique should be used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook” (order code 9398 652 90011).
• The footprint must be at an angle of 45° to the board
direction and must incorporate solder thieves
downstream and at the side corners.
Reflow soldering
Even with these conditions, do not consider wave
soldering the following packages: QFP52 (SOT379-1),
QFP100 (SOT317-1), QFP100 (SOT317-2),
Reflow soldering techniques are suitable for all QFP
packages.
QFP100 (SOT382-1) or QFP160 (SOT322-1).
The choice of heating method may be influenced by larger
plastic QFP packages (44 leads, or more). If infrared or
vapour phase heating is used and the large packages are
not absolutely dry (less than 0.1% moisture content by
weight), vaporization of the small amount of moisture in
them can cause cracking of the plastic body. For more
information, refer to the Drypack chapter in our “Quality
Reference Handbook” (order code 9397 750 00192).
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Maximum permissible solder temperature is 260 °C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150 °C within
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
6 seconds. Typical dwell time is 4 seconds at 250 °C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from
215 to 250 °C.
Repairing soldered joints
Fix the component by first soldering two diagonally-
opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300 °C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320 °C.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45 °C.
1997 Jun 16
39
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
DEFINITIONS
Data sheet status
Objective specification
Preliminary specification
Product specification
This data sheet contains target or goal specifications for product development.
This data sheet contains preliminary data; supplementary data may be published later.
This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
PURCHASE OF PHILIPS I2C COMPONENTS
Purchase of Philips I2C components conveys a license under the Philips’ I2C patent to use the
components in the I2C system provided the system conforms to the I2C specification defined by
Philips. This specification can be ordered using the code 9398 393 40011.
1997 Jun 16
40
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
NOTES
1997 Jun 16
41
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
NOTES
1997 Jun 16
42
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
NOTES
1997 Jun 16
43
Philips Semiconductors – a worldwide company
Argentina: see South America
Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB,
Tel. +31 40 27 82785, Fax. +31 40 27 88399
Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113,
Tel. +61 2 9805 4455, Fax. +61 2 9805 4466
New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND,
Tel. +64 9 849 4160, Fax. +64 9 849 7811
Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213,
Tel. +43 1 60 101, Fax. +43 1 60 101 1210
Norway: Box 1, Manglerud 0612, OSLO,
Tel. +47 22 74 8000, Fax. +47 22 74 8341
Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6,
220050 MINSK, Tel. +375 172 200 733, Fax. +375 172 200 773
Philippines: Philips Semiconductors Philippines Inc.,
106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI,
Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474
Belgium: see The Netherlands
Brazil: see South America
Poland: Ul. Lukiska 10, PL 04-123 WARSZAWA,
Tel. +48 22 612 2831, Fax. +48 22 612 2327
Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor,
51 James Bourchier Blvd., 1407 SOFIA,
Tel. +359 2 689 211, Fax. +359 2 689 102
Portugal: see Spain
Romania: see Italy
Canada: PHILIPS SEMICONDUCTORS/COMPONENTS,
Tel. +1 800 234 7381
Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW,
Tel. +7 095 755 6918, Fax. +7 095 755 6919
China/Hong Kong: 501 Hong Kong Industrial Technology Centre,
72 Tat Chee Avenue, Kowloon Tong, HONG KONG,
Tel. +852 2319 7888, Fax. +852 2319 7700
Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231,
Tel. +65 350 2538, Fax. +65 251 6500
Colombia: see South America
Czech Republic: see Austria
Slovakia: see Austria
Slovenia: see Italy
Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S,
Tel. +45 32 88 2636, Fax. +45 31 57 0044
South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale,
2092 JOHANNESBURG, P.O. Box 7430 Johannesburg 2000,
Tel. +27 11 470 5911, Fax. +27 11 470 5494
Finland: Sinikalliontie 3, FIN-02630 ESPOO,
Tel. +358 9 615800, Fax. +358 9 61580920
South America: Rua do Rocio 220, 5th floor, Suite 51,
04552-903 São Paulo, SÃO PAULO - SP, Brazil,
Tel. +55 11 821 2333, Fax. +55 11 829 1849
France: 4 Rue du Port-aux-Vins, BP317, 92156 SURESNES Cedex,
Tel. +33 1 40 99 6161, Fax. +33 1 40 99 6427
Spain: Balmes 22, 08007 BARCELONA,
Tel. +34 3 301 6312, Fax. +34 3 301 4107
Germany: Hammerbrookstraße 69, D-20097 HAMBURG,
Tel. +49 40 23 53 60, Fax. +49 40 23 536 300
Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM,
Tel. +46 8 632 2000, Fax. +46 8 632 2745
Greece: No. 15, 25th March Street, GR 17778 TAVROS/ATHENS,
Tel. +30 1 4894 339/239, Fax. +30 1 4814 240
Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH,
Tel. +41 1 488 2686, Fax. +41 1 481 7730
Hungary: see Austria
India: Philips INDIA Ltd, Shivsagar Estate, A Block, Dr. Annie Besant Rd.
Worli, MUMBAI 400 018, Tel. +91 22 4938 541, Fax. +91 22 4938 722
Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1,
TAIPEI, Taiwan Tel. +886 2 2134 2865, Fax. +886 2 2134 2874
Indonesia: see Singapore
Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd.,
209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260,
Tel. +66 2 745 4090, Fax. +66 2 398 0793
Ireland: Newstead, Clonskeagh, DUBLIN 14,
Tel. +353 1 7640 000, Fax. +353 1 7640 200
Israel: RAPAC Electronics, 7 Kehilat Saloniki St, PO Box 18053,
TEL AVIV 61180, Tel. +972 3 645 0444, Fax. +972 3 649 1007
Turkey: Talatpasa Cad. No. 5, 80640 GÜLTEPE/ISTANBUL,
Tel. +90 212 279 2770, Fax. +90 212 282 6707
Italy: PHILIPS SEMICONDUCTORS, Piazza IV Novembre 3,
20124 MILANO, Tel. +39 2 6752 2531, Fax. +39 2 6752 2557
Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7,
252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461
Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108,
Tel. +81 3 3740 5130, Fax. +81 3 3740 5077
United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes,
MIDDLESEX UB3 5BX, Tel. +44 181 730 5000, Fax. +44 181 754 8421
Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL,
Tel. +82 2 709 1412, Fax. +82 2 709 1415
United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409,
Tel. +1 800 234 7381
Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR,
Tel. +60 3 750 5214, Fax. +60 3 757 4880
Uruguay: see South America
Vietnam: see Singapore
Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905,
Tel. +9-5 800 234 7381
Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD,
Tel. +381 11 625 344, Fax.+381 11 635 777
Middle East: see Italy
For all other countries apply to: Philips Semiconductors, Marketing & Sales Communications,
Internet: http://www.semiconductors.philips.com
Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825
© Philips Electronics N.V. 1997
SCA54
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed
without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license
under patent- or other industrial or intellectual property rights.
Printed in The Netherlands
547047/1200/01/pp44
Date of release: 1997 Jun 16
Document order number: 9397 750 01744
相关型号:
©2020 ICPDF网 联系我们和版权申明