TDA9614H [NXP]
Audio processor for VHS hi-fi and linear audio; 音频处理器的VHS Hi-Fi和线性音频
| 型号： | TDA9614H |
| 厂家： | 
NXP |
| 描述： | Audio processor for VHS hi-fi and linear audio |
| 文件： | 总60页 (文件大小：569K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
INTEGRATED CIRCUITS
DATA SHEET
TDA9614H
Audio processor for VHS hi-fi
and linear audio
1995 Mar 21
Preliminary specification
File under Integrated Circuits, IC02
Philips Semiconductors
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
CONTENTS
12
TEST AND APPLICATION INFORMATION
12.1
12.2
RAF I/O (pin 12)
RCCOL, RCCOR, RBPF and RFIX
(pins 59, 53, 55 and 49)
1
2
3
4
5
6
FEATURES
GENERAL DESCRIPTION
ORDERING INFORMATION
BLOCK DIAGRAM
13
14
PACKAGE OUTLINE
SOLDERING
PINNING
14.1
Plastic quad flat packages
By wave
By solder paste reflow
Repairing soldered joints (by hand-held
soldering iron or pulse-heated solder tool)
14.1.1
14.1.2
14.1.3
FUNCTIONAL DESCRIPTION
6.1
Audio I/O switching
Input Select (InputSel)
Normal Select (NormSel)
Volume L/R; AGC
6.1.1
6.1.2
6.1.3
6.1.4
15
16
17
DEFINITIONS
Audio FM Output Mute (AFOMute); Normal
Output Mute (NOMute)
Output Select (OutSel)
RF Converter Mute (RFCMute)
Line Select (LineSel)
Decoder Select (DecodeSel)
Headphone Select (HPSel)
Headphone volume
DC Select (DCSel)
Linear audio circuits
Record/loop-through
Playback
LIFE SUPPORT APPLICATIONS
PURCHASE OF PHILIPS I2C COMPONENTS
6.1.5
6.1.6
6.1.7
6.1.8
6.1.9
6.1.10
6.1.11
6.2
6.2.1
6.2.2
6.3
Audio FM circuits
6.3.1
6.3.2
6.3.3
6.3.4
6.4
Record/loop-through
Playback
Automatic calibration
PAL/NTSC mode
I2C-bus
6.5
Power-On Reset (POR); derived from digital
supply voltage VDDD
Control byte
6.6
6.7
Main select byte
6.8
6.9
6.10
6.11
6.12
6.13
Secondary select byte
Left/Right (L/R) volume byte
Headphone volume byte
Install byte
Test byte
Read byte
7
LIMITING VALUES
8
THERMAL CHARACTERISTICS
DC CHARACTERISTICS
AC CHARACTERISTICS
9
10
10.1
10.2
10.3
10.4
Record audio FM mode
Record linear audio mode
Playback Audio FM mode
Playback linear audio
11
INTERNAL CIRCUITRY
1995 Mar 21
2
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
1
FEATURES
2
GENERAL DESCRIPTION
• All functions controlled by I2C-bus
The TDA9614H is an audio processing IC for VHS hi-fi and
linear audio, digitally controlled via the I2C-bus. The
FM (de)modulator and peak noise reduction functions are
highly integrated, resulting in few external components
and no external adjustments.
• No adjustments needed by use of auto-calibration circuit
• Integrated Bandpass Filters (BPFs)
• Low-noise Phase-Locked Loop (PLL) FM (de)modulator
• Low-distortion sample-and-hold switching noise
suppressor
In addition special functions for audio mixing, dubbing and
descrambling have been implemented.
• Integrated HF Low-Pass Filter (LPF) and summator
• Integrated audio LPF
• 5 stereo inputs (left and right channel):
– TUNL and TUNR
– CINL and CINR
– EXT1L and EXT1R
– EXT2L and EXT2R
– EXT3L and EXT3R
• Additional mono input: Second Audio Program (SAP)
• Independent Input/Output (I/O) selections and 2nd line
output
• Linear audio
• DC output for VU meter drive
• Direct headphone drive
• RF converter output with overload Automatic Gain
Control (AGC)
• Integrated standby mode for low current consumption
• E-E performance (record + playback):
– Total Harmonic Distortion (THD): 0.05%
(−8 dBV, 1 kHz)
– linearity error: 0.1 dB (−88 dBV, 1 kHz)
– noise: −93 dBV (20 Hz to 20 kHz).
3
ORDERING INFORMATION
PACKAGE
TYPE NUMBER
NAME
DESCRIPTION
VERSION
TDA9614H
QFP64(1) plastic quad flat package; 64 leads (lead length 1.95 mm);
SOT319-2
body 14 × 20 × 2.8 mm
Note
1. When using IR reflow soldering it is recommended that the Drypack instructions in the “Quality Reference Handbook”
(order number 9398 510 63011) are followed.
1995 Mar 21
3
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
4
BLOCK DIAGRAM
BM2E75
a
1995 Mar 21
4
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
5
PINNING
SYMBOL
PIN
DESCRIPTION
Second Audio Program (SAP) input.
SAP
1
2
TUNL
TUNR
CINL
Left channel tuner input.
3
Right channel tuner input.
Left channel cinch input.
4
CINR
5
Right channel cinch input.
Left channel external 1 input.
Right channel external 1 input.
Left channel external 2 input.
Right channel external 2 input.
Left channel external 3 input.
Right channel external 3 input.
EXT1L
EXT1R
EXT2L
EXT2R
EXT3L
EXT3R
RAF
6
7
8
9
10
11
12
Record/playback switch drive output for head amplifier control or input for overruling
the I2C-bit RAF.
VDDD
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Digital supply voltage for I2C-bus (+5 V).
Data input/output for I2C-bus.
Clock input for I2C-bus.
SDA
SCL
VSSD
Digital ground for I2C-bus.
RFCAGC
RFCOUT
LINE2L
LINE2R
LINEL
RF converter AGC-time constant.
RF converter drive output.
Line 2 left output (e.g. decoder output).
Line 2 right output (e.g. decoder output).
Line output left.
LINER
Line output right.
DCOUTL
DCOUTR
HPOUTL
HPOUTR
LINAGC
LININ
VU meter drive output left.
VU meter drive output right.
Headphone drive output left.
Headphone drive output right.
Linear audio AGC-time constant.
Audio input for linear audio to REC equalizer and output select.
Audio output from AGC or PB equalizer.
Long Play (LP) equalization switch; 15 Ω on resistance and 150 kΩ input impedance.
LINOUT
EQSW
RECEQ
Linear audio recording amplifier negative feedback input for connecting a record
equalization network.
LINREC
32
Digital output controlled by I2C-bit RN; can be used to drive an external (high voltage)
head switch and possibly the bias oscillator.
RECOUT
PBIN
33
34
Linear audio recording amplifier output.
Linear audio playback amplifier input; during playback the impedance is 100 kΩ;
during record the impedance is 7 Ω.
RESSW
PBDC
35
36
Long Play equalization switch 50 Ω on and 150 kΩ off impedance to PBIN.
Linear audio playback amplifier DC decoupling.
1995 Mar 21
5
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
SYMBOL
DCFBL
PIN
DESCRIPTION
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
DC feedback left.
DCREFL
EMPHL
RECTL
DETL
DC reference left.
Total emphasis left (240 to 20 µs).
Rectifier DC decoupling left.
Attack/recovery timing left.
Vref
Noise filtering of 3.8 V reference voltage (external capacitor required for filtering).
Analog ground 1 for LF circuits.
VSSA1
DETR
Attack/recovery timing right.
RECTR
EMPHR
DCREFR
DCFBR
RFIX
Rectifier DC decoupling right.
Total emphasis right (240 to 20 µs).
DC reference right.
DC feedback right.
Fixed bias current generation circuit by using an external 180 kΩ resistor to ground.
Analog supply voltage 1 for LF circuits (+12 V).
VDDA1
AFNR
Audio output from noise reduction of right channel (record and loop-through) or audio
input for noise reduction of right channel (playback).
AFMR
52
53
Audio input for audio clipper of right channel (record and loop-through) or audio
output from sample-and-hold (playback).
RCCOR
Voltage-to-current transfer for right channel oscillator by means of an external resistor
to ground.
VSSA2
RBPF
54
55
Analog ground 2 for HF circuits.
Bias current generation for the internal band-pass filters by means of an external
resistor to ground.
FMOUT
FMIN
56
57
58
59
FM output.
FM input.
VDDA2
Analog supply voltage 2 for HF circuits (+5 V).
RCCOL
Voltage-to-current transfer for left channel oscillator by means of an external resistor
to ground.
ENVOUT
HID
60
61
62
63
Level detector output (external capacitor required for filtering).
Head Identification Pulse (HID) input for sample-and-hold circuits.
Mute timing (external capacitor required for playback mute).
CMUTE
AFML
Audio input for audio clipper of left channel (record and loop-through) or audio output
from sample-and-hold circuit of left channel (playback).
AFNL
64
Audio output from noise reduction of left channel (record and loop-through) or audio
input for noise reduction of left channel (playback).
1995 Mar 21
6
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
SAP
TUNL
1
2
51
50
49
48
AFNR
V
DDA1
3
TUNR
CINL
RFIX
4
DCFBR
5
47 DCREFR
46 EMPHR
CINR
6
EXT1L
EXT1R
EXT2L
EXT2R
EXT3L
7
45
44
43
42
RECTR
DETR
8
V
9
SSA1
10
TDA9614H
V
ref
EXT3R 11
41 DETL
12
13
14
15
16
17
18
19
40 RECTL
RAF
V
39
38
EMPHL
DDD
SDA
SCL
DCREFL
37 DCFBL
V
36
35
34
33
PBDC
SSD
RESSW
PBIN
RFCAGC
RFCOUT
LINE2L
RECOUT
MBE278
Fig.2 Pin configuration.
7
1995 Mar 21
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
6
FUNCTIONAL DESCRIPTION
BM2E76
1995 Mar 21
8
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
3. SAP (SAP input).
6.1
Audio I/O switching
This setting enables simultaneous recording of the
NTSC SAP signal on the linear track and TUNER
stereo on the audio FM track. When receiving a
NICAM audio signal, the linear audio can be used as a
‘backup’ track when received television signals are
weak.
6.1.1
INPUT SELECT (INPUTSEL)
For the audio FM circuitry eight different audio signals can
be selected. The selection made here for hi-fi is also
available for the linear audio circuitry.
1. TUNER (stereo input; internal tuner of VCR).
2. CINCH (stereo input; connection to hi-fi set).
3. EXT1 (stereo input; TV SCART1).
4. TUNER LEFT (left channel [language 1] of TUNER
input).
When receiving dual language transmissions the main
language (language 1) can be recorded on linear
audio. Note that if the SAP input is not used it can be
connected to the right TUNER channel, enabling
language selection for linear audio.
4. EXT2 (stereo input; decoder, 2nd VCR SCART2).
5. EXT3 (stereo input; front CINCH for e.g. camcorder).
6. SAP (mono input; ‘Second Audio Program’ audio
carrier for NTSC or conventional FM carrier with
NICAM reception).
6.1.3
VOLUME L/R; AGC
7. NORMAL (linear audio; [playback] signal of linear
audio).
The volume controls are mainly intended for level
adjusting of the audio signals to be recorded on the hi-fi
track, however using the ‘VOLUME’ setting in the Normal
Select it can also be used to control linear audio. The
volume controls have a control range of +14 dB to −49 dB
in 1 dB steps and a full mute. Because the volume controls
are I2C-bus controlled their actual behaviour is defined by
the VCR’s software. For instance user control can be
‘volume only’, ‘left + right’, ‘volume + balance’ or the
setting can be defined by a ‘digital AGC’ software loop
using the signals at the DC (VU meter) outputs.
When inserting a new video signal in an old
audio/video recording the hi-fi audio track is erased.
This setting can keep the current audio available on
the hi-fi track by copying the (playback) linear audio
signal to the hi-fi track during video insert.
8. EXT3/ST (input mix; mono EXT3 on left, mono hi-fi on
right channel).
For linear audio use see Section 6.1.2.
6.1.2
NORMAL SELECT (NORMSEL)
The linear audio level can be controlled by an AGC circuit,
which can be switched off when desired. In most cases the
AGC should be used at all settings of the Normal Select
except for ‘VOLUME’.
For linear audio four settings can be selected:
1. INPUTSEL (mono signal from input select).
This is the ‘standard’ setting. The signal source
selected with the input select is led to the linear audio
circuit. The linear audio AGC should be switched on.
6.1.4
AUDIO FM OUTPUT MUTE (AFOMUTE);
NORMAL OUTPUT MUTE (NOMUTE)
2. VOLUME (mono signal from [hi-fi] volume control).
The audio output signal of the audio FM circuit can be
muted with AFOMute, the linear output signal can be
muted using NOMute. If one of these signals is not used
as an output (or input) signal it is best muted to further
minimize crosstalk.
The signal source selected with the input select has
now volume control, the linear audio AGC should be
switched off. This setting is for use with ‘audio
dubbing’: inserting a new audio signal on the linear
track in an old audio/video recording. A special audio
dubbing feature is now possible by selecting ‘input mix’
EXT3/ST in the input select. This setting enables us to
use the VCR as a mixer console: an audio source
connected to EXT3 (front CINCH) can be adjusted and
mixed together with the original hi-fi playback signal,
using the left (EXT3) and right (hi-fi playback) volume
controls.
6.1.5
OUTPUT SELECT (OUTSEL)
This block is the ‘main’ output select function, possibly
functional on all outputs. Each output however has some
means to override this selection for its own output signal,
to implement extra features. Eight selections are possible
and they are shown in Table 1.
1995 Mar 21
9
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
Table 1 Output select possibilities
SELECTION
REMARK
hi-fi stereo
DESCRIPTION
audio FM output signal left and right channel
STEREO(1)
LEFT
hi-fi left
audio FM output signal left channel (language 1)
audio FM output signal right channel (language 2)
linear audio
RIGHT
hi-fi right
NORMAL
NOR + ST
NOR + L
NOR + R
MUTE
linear audio
linear and hi-fi
linear and left
linear and right
mute
mix of audio FM stereo and linear audio
mix of audio FM left channel and linear audio
mix of audio FM right channel and linear audio
Note
1. STEREO is the ‘standard’ setting, LEFT and RIGHT are for language selection. Using the tuner as input or output
signal (record or loop-through of audio FM) the VCR can automatically switch from stereo to left (language 1) when
a ‘dual language’ transmission is received. If the VCR is in playback mode and no hi-fi track is present (checking bit
AFOM via the I2C-bus or using the level at pin 11) the VCR can switch the output select to NORMAL (or let the IC
do this automatically by setting bit AUTN). If a hi-fi track is present the user may want to switch to LEFT and RIGHT
if the recording made was a ‘dual language’ recording.
Furthermore the user may want to switch from a hi-fi selection to NORMAL, e.g. when a complete audio remix has
been created on the linear track using ‘audio dubbing’ (see Section 6.7). ‘Audio dubbing’ can also be used to
re-record the linear track with e.g. only commentary. Combined playback of this commentary together with the
original hi-fi sound is then possible by means of a mix mode.
6.1.6
RF CONVERTER MUTE (RFCMUTE)
The RFC output is a mono output derived from the output select, its output signal can be muted.
6.1.7
LINE SELECT (LINESEL)
The line output select is normally connected to both CINCH (hi-fi set) and television (SCART1). Normally the audio signal
from the output select will be available at this output, but three extra selections are possible and they are shown in
Table 2.
Table 2 Extra line select possibilities
SELECTION
NORMAL
EXT2(1)
DESCRIPTION
linear audio, useful for monitoring during ‘audio dubbing’
audio from input EXT2
EXT3(2)
audio from input EXT3
Notes
1. A signal from a source at EXT2 (laser disc or second VCR) can be connected to a television set at line out. Because
this is a direct connection from the input to the line output buffers it is fully independent of any mode setting of the
IC. Connection of a ‘Pay-TV’ decoder box to EXT2 and using this selection together with selecting EXT1 in the
decoder select enables combined use of the decoder box by both TV and VCR. In Europe, use of the SCART
connector ‘status line’ can automatize this switching.
2. Direct audio connection from input EXT3. If the line 2 outputs and EXT3 inputs are not used for external connections
a built-in karaoke unit or sound processor can be inserted between line 2 and EXT3.
1995 Mar 21
10
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
both hi-fi audio channels, independent from the setting of
output or headphone select. For this mode the selection
STEREO can be made.
6.1.8
DECODER SELECT (DECODESEL)
The line 2 output is normally connected to a decoder box
or e.g. a second VCR (SCART2). Normally the audio
signal from the output select will be available at this output,
but three extra selections are shown in Table 3.
6.2
Linear audio circuits
6.2.1
RECORD/LOOP-THROUGH
Table 3 Extra decoder select possibilities
The signal selected with the normal select can be level
controlled in the AGC block. If wanted this AGC can be
switched off using bit AGCN. The audio signal is thereafter
DC decoupled using a capacitor between pin 29 (LINOUT)
and pin 28 (LININ).
SELECTION
DESCRIPTION
TUNER(1)
EXT1(2)
EXT3
audio from input TUNER
audio from input EXT1
audio from input EXT3
From here on the signal goes to the output select and (in
the event of record mode) to the record equalizer. The
record equalizer is a non-inverting amplifier with a gain of
+12 dB, consisting of an opamp with feedback resistors,
and acts as a pre-correction filter for the tape and head
characteristics. The inverting input of the opamp is
connected to pin 31 (RECEQ), its output to pin 33
(RECOUT). The circuit externally connected between
pin 31 and ground defines the transfer of the record
Notes
1. Enables the use of a decoder box (connected to line 2
[EXT2]) by the VCR.
2. Decoder box connection to television set
(See Section 6.1.7).
6.1.9
HEADPHONE SELECT (HPSEL)
(1200 + Z)
The headphone output will normally carry the output select
signal, however three more selections are possible and
shown in Table 4.
equalizer with equation: A = 3.98 ×
-----------------------------
Z
Where: Z is the complex impedance of the external circuit.
Two equalizings can be used, switching additional circuitry
to ground with pin 30 (EQSW) in long play or extended
play (I2C-bus: LP = 1).
Table 4 Extra headphone select possibilities
SELECTION
LEFT(1)
DESCRIPTION
left hi-fi channel
Instead of the hi-fi circuit, linear audio has two
loop-through modes:
RIGHT(1)
right hi-fi channel
NORMAL
linear audio, useful for monitoring the
recording by ‘audio dubbing’
• Loop-through playback
• Loop-through record.
Note
The only difference between Loop-through record and
record is the RECOUT output, which is muted.
1. The selections LEFT and RIGHT make it possible to
select a different language for the headphone as for
the line outputs. A possible implementation is to invert
always a language selection made at the output select.
The LINREC output (pin 32) is used to drive the external
high-voltage switch and possibly the bias oscillator. The
LINREC voltage has a small internal delay to be
non-overlapping with the internal switching to playback
mode. This ensures that no bias voltage will appear at the
PBIN input while the IC is in playback mode.
6.1.10 HEADPHONE VOLUME
The headphone volume control has a control range of
+16 dB to −47 dB in 1 dB steps and a full mute.
6.2.2
PLAYBACK
6.1.11 DC SELECT (DCSEL)
The signal coming from the head is amplified and can be
level controlled in 16 steps of 1 dB. This setting can be
used to adjust for spread or nominal difference in head
output level. Afterwards, the signal is frequency corrected
in the playback equalizer. This equalizer includes the two
standard VHS equalizing settings of 3180 and 120 µs
The VU meter output is normally connected to the
headphone select, but can also be switched to STEREO
(hi-fi stereo, before the output select). When using the
VU meter output signal to implement a ‘digital AGC’ (read
the level at the DC output, and adjust the VOLUME L/R
controls accordingly) it is necessary to have information of
1995 Mar 21
11
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
(standard play: LP = 0) and 3180 and 170 µs (Long Play:
LP = 1).
low-pass filtered audio signal is expanded in the noise
reduction.
The signal is DC decoupled and routed to the output select
via pins 29 and 28. When switching to or from playback
the signal should be muted shortly using the Normal
Output Mute (NOM) to prevent audible clicks caused by
offset differences of the playback amplifier and AGC.
If the left channel carrier at FMIN falls below the mute level
of 4.2 mV (RMS value) the audio signal is muted in front of
the low-pass filter. This is achieved by comparing the left
channel level detector signal with an internal reference.
The mute timing is fixed by a capacitor at the CMUTE pin.
If the level at CMUTE rises above a certain threshold, the
PBMUTE bit is set. This will mute the audio signal. If bit
AUTN has been set, the output selection will automatically
switch to NORMAL mode. The left channel level detector
output is also available at pin ENVOUT. An AGC
6.3
Audio FM circuits
6.3.1
RECORD/LOOP-THROUGH
After low-pass filtering and signal compression in the
Noise Reduction (NR) the audio signal is available at
AFNL and AFNR. Through a DC-decoupling capacitor the
compressed audio signal is fed to an audio clipper at
AFML and AFMR. Subsequently, the audio signal is
FM-modulated on a RF-carrier using an integrated
current-controlled oscillator (CCO). Each CCO (L and R)
requires an external resistor (RCCOL/R) for temperature
stability. Through automatic calibration both the oscillator
centre frequency and FM-deviation are adjusted. After
low-pass filtering and summation of the two RF-carriers,
the FM signal is available at FMOUT during record. During
loop-through the FMOUT pin is inactive.
correction voltage is added at this pin, such that the
ENVOUT voltage indicates the left channel FM-carrier
level even within the AGC-range. The ENVOUT voltage
can be used for auto-tracking of the FM-audio heads.
In the event of drop-outs in the incoming FM signal, the left
channel level detector is also used to activate the
sample-and-hold. This drop-out cancellation is only active
if bit DOC has been set.
6.3.3
AUTOMATIC CALIBRATION
By means of bit CALS the two integrated oscillators and
bandpass filters can be calibrated in Loop-Through (LT) or
record (REC) mode. Normally this will be done after
start-up of the VCR. After setting of bit CALS the
calibration procedure is automatically executed as shown
in Fig.4. The calibration starts at the first negative edge of
HID after CALS has been set. During the LOW period of
HID (20 ms for PAL) the number of oscillator cycles is
compared to a certain value stored in a Read Only Memory
(ROM).
The RAF pin reflects the status of the RAF-bit when it is
used as output pin. In this case it is meant to switch the
head amplifier between record and playback position. It
can also be used as an input pin to overrule the RAF-bit
thereby forcing the IC in record or playback/loop-through
position.
6.3.2
PLAYBACK
The two FM modulated RF carriers, presented at FMIN,
are fed to an AGC circuit. The AGC operates on the peak
level of the added BPF output signals. As a result, the input
signal of the BPFs is kept constant for FMIN voltages
>30 mV (RMS value) both carriers added. In this way the
dynamic range of the integrated BPFs is optimally used
over a large input signal range. Subsequently, the
RF carriers are bandpass filtered using two integrated
BPFs. These bandpass filters are automatically calibrated
as described in Section 6.3.3. An external resistor (RBPF)
is required for temperature stability.
Therefore, the final oscillator frequency is proportional to
the inverse of the HID LOW-time. This means that an error
of 1 µs in the HID LOW-time will result in an additional
frequency error of approximately 100 Hz. The maximum
number of required HID cycles for one complete oscillator
calibration is six, which is equal to 240 ms.
After both oscillators have been calibrated the bandpass
filters are calibrated using the right channel oscillator as
reference frequency generator (1.6 MHz for PAL). This will
take <10 ms.
Bit CALR is set to 1 if the calibration has been executed
successfully. CALR is 0 if:
The filtered input signals are fed to a limiter. The limiter
output signal is demodulated by means of a
PLL demodulator. The LF audio signal is fed through a
sample-and-hold circuit to suppress head-switching noise.
The demodulated audio is available at AFML and AFMR.
Through a decoupling capacitor the audio signal is applied
to an audio low-pass filter at AFNL and AFNR. The
• A Power-On Reset (POR) has occurred.
• The calibration is running.
• The initial oscillator and bandpass frequencies are too
low or too high for a successful calibration.
1995 Mar 21
12
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
CALS
HID
CALR
LEFT
OSCILLATOR
max 240 ms
RIGHT
OSCILLATOR
max 240 ms
BANDPASS
FILTERS
MBE281
max 10 ms
Fig.4 Timing diagram of automatic calibration.
If CALS is reset during CALR = 0, the calibration will be
stopped if it was not finished yet. If required, a new
calibration can be started using CALS.
WARNING: A change of PB to REC, LT to REC and
PAL to NTSC should not be combined in one transmitted
byte. The PAL to NTSC transition should be preceded by
the PB to REC or LT to REC transition.
WARNING: the IC should not be calibrated in a test or
standby mode.
6.4
I2C-bus
The TDA9614H is controlled via the 2-wire I2C-bus, in
accordance with the I2C-bus specification. As slave
receiver for programming there is one module address,
with R/W bit = 0, a subaddress byte and eight data bytes.
If more than one data byte follows the subaddress, these
bytes are stored in the successive registers by the
automatic address increment feature. As slave transmitter
(R/W bit = 1) there is one read byte.
6.3.4
PAL/NTSC MODE
Depending on bit NTSC the IC is calibrated in PAL or
NTSC mode using bit CALS. After an automatic calibration
the oscillator frequencies can be switched between PAL
and NTSC using bit NTSC. This centre frequency shift is
done without automatic calibration. During playback (PB)
or loop-through (LT) a change in bit NTSC will
automatically calibrate the bandpass filters again. This will
take <10 ms.
1995 Mar 21
13
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
Table 5 TDA9614H addresses and data bytes
NAME
ADDRESS
Slave address byte
1
0
0
0
1
0
1
1
0
0
0
X(1)
R/W
X(1)
Subaddress bytes 00 to 07
Control byte (subaddress 00)
0
X(1)
IPN
OSL
RAF
IS2
IPAF
IS1
AFOM
IS0
NTSC
NS1
RN
NS0
NOM
OSR
LP
Main select byte
(subaddress 01)
OSN
Secondary select byte
(subaddress 02)
HSL
HSR
VLM
VRM
VHM
DCS
VL5
VR5
VH5
RFCM
VL4
LOS1
VL3
LOS0
VL2
DOS1
VL1
DOS0
VL0
Left volume byte
(subaddress 03)
0
0
0
Right volume byte
(subaddress 04)
VR4
VH4
VR3
VH3
VR2
VH2
VR1
VH1
VR0
VH0
Headphone volume byte
(subaddress 05)
Install byte (subaddress 06)
Test byte (subaddress 07)
Read byte (address B9)
DEV1
STBY
CALR
DEV0
CALS
PAFM
NPL3
AGCN
1
NPL2
TST4
POR
NPL1
TST3
1
NPL0
TST2
0
AUTN
TST1
1
DOC
TST0
1
Note
1. These bits determine the subaddress.
6.5 Power-On Reset (POR); derived from digital supply voltage VDDD
In the data byte descriptions [por] indicates the mode after POR. The status of the data bytes after POR is shown in
Table 6.
Table 6 Status of data bytes after POR
DATA BYTE
Control byte
ADDRESS
0
0
1
0
0
0
0
0
1
0
1
0
0
0
1
0
1
0
0
1
1
1
0
0
0
0
0
0
0
0
1
1
0
1
1
0
0
0
1
1
0
1
1
0
0
0
1
0
0
0
0
0
1
1
1
1
0
Main select byte
Secondary select byte
Left volume byte
Right volume byte
Headphone volume byte
Install byte
0
0
1
1
0
1
0
Test byte
A POR occurrence is signalled by bit POR in the read byte (see Table 39).
1995 Mar 21
14
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
6.6
Control byte
Table 7 Bits of control byte
BIT
DESCRIPTION
RAF
IPAF
AFOM
NTSC
RN
Record Audio FM; see Table 8
Inverse Playback Audio FM; see Table 8
Audio FM Output Mute; see Table 9
NTSC; television standard; see Table 10
Record Normal; see Table 11
IPN
Inverse Playback Normal; see Table 11
Normal Output Mute; see Table 12
Long Play mode; see Table 13
NOM
LP
Table 8 Bits RAF and IPAF
RAF(1)
IPAF
MODE
playback
DESCRIPTION
NR and modem in playback mode
0
0
1
1
0
1
0
1
loop-through
record(2)
record(2)
NR in record mode; modem not active [por]
NR and modem in record mode
NR and modem in record mode
Notes
1. The RAF bit can be overruled externally by applying a low-ohmic voltage to the RAF I/O (pin 12) either logic 0 or
logic 1 (0 or +5 V). The actual mode of the IC is determined by the level measured at this pin, enabling fast switching
between record and playback/loop-through.
2. The two record modes are equal, only differing in their reaction to forcing RAF LOW at the RAF I/O pin; the status of
the IPAF bit determines whether the IC is switched to the playback or loop-through mode.
Table 9 Bit AFOM
AFOM
MODE
DESCRIPTION
0
1
−
−
mute(1)
output from audio FM (NR) circuit is muted [por]
Note
1. Audio coming from the audio FM circuit is muted, either the signal from tape in playback or the loop-through signal
in record or loop-through modes.
Table 10 Bit NTSC
NTSC
MODE
DESCRIPTION
0
1
PAL
modem and BPF set to PAL carrier frequencies [por]
modem and BPF set to NTSC carrier frequencies
NTSC
1995 Mar 21
15
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
Table 11 Bits RN and IPN
RN(1)
IPN
MODE
DESCRIPTION
0
0
1
1
0
1
0
1
playback
linear audio circuit in playback mode
loop-through P
loop-through R(2)
record
linear audio circuit in loop-through mode (playback ready) [por]
linear audio circuit in loop-through mode (record ready)
linear audio circuit in record mode
Notes
1. Bit RN is output at LINREC (pin 32), which is used to drive an external (high voltage) head switch and possibly the
bias oscillator. The two loop-through modes are equal in signal flow, however they differ in the state of the head
switches (the internal switch at PBIN [pin 34] and the external head switch driven by pin LINREC).
2. Loop-through R is equal to record except for the RECOUT output (pin 33) which is muted.
Table 12 Bit NOM
NOM
MODE
DESCRIPTION
0
1
−
−
mute(1)
output from linear audio circuit is muted [por]
Note
1. Audio coming from the linear audio circuit is muted, either the signal from tape in playback or the loop-through signal
in record or loop-through modes. To avoid clicks when changing the mode of the linear audio circuit to or from
playback, the output should be muted shortly, using this bit.
Table 13 Bit LP
LP
MODE
DESCRIPTION
0
SP
Record and playback equalizing set for Standard Play [por].
Record equalization switch at EQSW (pin 30) and playback equalization switch at RESSW
(pin 35) are open (high impedance). The internal playback equalizing is 3180 and 120 µs.
It can be changed to 2544 and 96 µs by selecting test number 31 (see Section 6.12).
1
LP
Record and playback equalizing set for Long Play.
Record equalization switch at EQSW (pin 30) and playback equalization switch at RESSW
(pin 35) are closed. The internal playback equalizing is 3180 and 170 µs. It can be
changed to 2731 and 146 µs by selecting test number 31 (see Section 6.12).
1995 Mar 21
16
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
6.7
Main select byte
Table 14 Bits of main select byte
BIT
DESCRIPTION
IS2 to IS0
NS1 and NS0
OSL
Input Select 2 to Input Select 0; see Table 15
Normal Select 1 and Normal Select 0; see Table 16
Output Select Left; see Table 17
OSR
Output Select Right; see Table 17
OSN
Output Select Normal; see Table 17
Table 15 Bits IS2 to IS0; note 1
IS2
0
IS1
0
IS0
0
MODE
Tuner
SELECTED INPUT SOURCE
TUNL and TUNR [por]
CINL and CINR
0
0
1
Cinch
0
1
0
Ext1
EXT1L and EXT1R (e.g. SCART1; TV connector)
EXT2L and EXT2R (e.g. SCART2; decoder connector)
EXT3L and EXT3R (e.g. front cinch)
0
1
1
Ext2
1
0
0
Ext3
1
0
1
SAP
additional mono input (SAP; pin 1)
1
1
0
Normal(2)
Dub Mix (2)(3)
output from linear audio (LININ; pin 28)
mixing of EXT3 input with hi-fi output signal
1
1
1
Notes
1. With bits IS2 to IS0, the stereo input signal is selected which is led to the hi-fi processing. One out of five stereo
sources can be selected. The five stereo inputs differ in their connectivity; with bits NS1 and NS0 tuner left
(TUNL; pin 2) can be selected as linear audio input source, with bits LOS1 and LOS0 Normal, Ext2 and Ext3 are
directly connectable to Line out and to DOS1 and DOS0 Tuner, Ext1 and Ext3 are directly connectable to decoder
out (2nd Line Out).
2. Remark: when using the selections Normal or Dub Mix be aware of signal loops (which should be avoided) because
this can lead to large audio oscillations.
3. The selection Dub Mix is a special function in which a mono signal derived from the Ext3 inputs
(1⁄2EXT3L + 1⁄2EXT3R) is led to the left input and a mono signal derived from the audio FM output (1⁄2L + 1⁄2R) is led
to the right input channel. This function can be used for audio dubbing using the volume controls as a mixing desk.
Table 16 Bits NS1 and NS0; note 1
NS1
NS0
MODE
Input
DESCRIPTION
0
0
1
1
0
1
0
1
linear audio input source is equal to hi-fi input [por]
linear audio input source is equal to hi-fi input, inclusive volume control
additional mono input (SAP; pin 1) is selected
Volume
SAP
Tuner L
left channel of tuner input is selected
Note
1. With bits NS1 and NS0 the input signal is selected for the linear audio circuit. When a stereo input source is selected,
a mono signal is made by adding the left and right channel. Furthermore two independent selections can be made
(the mono input SAP or the left channel of tuner e.g. for dual language). If in the volume mode the built-in AGC circuit
is switched off by using bit AGCN, the audio level can be controlled by the left and right volume controls
(VLx and VRx).
1995 Mar 21
17
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
Table 17 Bits OSL, OSR and OSN; note 1
OSL
OSR
OSN
MODE
stereo
DESCRIPTION
1
1
0
0
1
1
0
1
0
1
0
0
0
0
1
LEFT at left channel; RIGHT at right channel [por].
LEFT at both left and right channels.
RIGHT at both left and right channels.
No selection.
left
right
mute
mixed stereo
LEFT + NORMAL added at left channel; RIGHT + NORMAL added at
right channel.
1
0
0
0
1
0
1
1
1
mixed left
mixed right
normal
LEFT + NORMAL added at both left and right channels.
RIGHT + NORMAL added at both left and right channels.
NORMAL (is linear audio) at both left and right channels.
Note
1. The bits OSL, OSR and OSN provide eight output select functions. LEFT and RIGHT are the left and right hi-fi
channels; NORMAL is the linear audio channel (LININ; pin 28). This selection is normally output at line out (LINEL
and LINER), RFCOUT (pin 18), decoder out (LINE2L and LINE2R), headphone out (HPOUTL and HPOUTR) and
DC out (DCOUTL and DCOUTR). However line out can be overruled by bits LOS1 and LOS0; decoder out can be
overruled by bits DOS1 and DOS0, headphone out (and DC out) can be overruled by bits HSL and HSR and DC out
can be overruled by bit DCS.
Remark: if AUTN = 1 (see Section 6.11) the output select modes stereo, left and right will be forced to normal as long
as the audio FM circuit is in playback mode and the internal PB mute signal is generated (no hi-fi track on tape). The
status of this internal mute signal can be read by bit PAFM (see Section 6.13).
6.8
Secondary select byte
Table 18 Bits of secondary select byte
BIT
DESCRIPTION
Headphone Select Left; see Table 19
Headphone Select Right; see Table 19
HSL
HSR
DCS
DC Select; see Table 20
RFCM
RFC Mute; see Table 21
LOS1 and LOS0
DOS1 and DOS0
Line Output Select 1 and Line Output Select 0; see Table 22
Decoder Output Select 1 and Decoder Output Select 0; see Table 23
1995 Mar 21
18
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
Table 19 Bits HSL and HSR
HSL
HSR
MODE
DESCRIPTION
1
1
0
0
1
0
1
0
outsel
left
Headphone signal set by the output selection [por].
LEFT at both headphone out left and right.
right
RIGHT at both headphone out left and right.
NORMAL (is linear audio) at both headphone outputs.
normal
Normally the headphone output signal is set by the output selection OSL, OSR and OSN (see Table 17). Furthermore
three independent selections can be made: LEFT hi-fi channel, RIGHT hi-fi channel (language selection) and NORMAL
(e.g. monitoring an audio dubbing recording). These headphone selections are also active for the VU meter output
(DC out), unless bit DCS = 1.
Table 20 Bit DCS
DCS
MODE
headphone
stereo
DESCRIPTION(1)
0
1
DC output is set by Headphone Select [por].
DC output is hi-fi stereo.
Note
1. The signal at DC out (DCOUTL and DCOUTR; pins 23 and 24) is normally the signal which can be listened to by the
headphone. For use in concepts with digital AGC (using the DC output signal to control the left and right volume
settings), an independent selection to hi-fi stereo can be made.
Table 21 Bit RFCM
RFCM
MODE
DESCRIPTION(1)
0
1
−
[por]
RF converter output signal muted
mute(1)
Note
1. The audio signal at RF converter out (a mono version of the signal selected with the output select with overload AGC)
can be independently muted.
Table 22 Bits LOS1 and LOS0; note 1
LOS1
LOS0
MODE
DESCRIPTION
0
0
1
1
0
1
0
1
Outsel
Normal
Ext2
Line output selection is set by output select function [por].
Linear audio is connected to line output.
Ext2 input is directly connected to line output.
Ext3 input is directly connected to line output.
Ext3
Note
1. With the line output select some special connections can be made overruling the output select (OSL, OSR and OSN),
e.g. for connecting a decoder box (for a pay-TV channel) to a television set via the VCR.
1995 Mar 21
19
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
Table 23 Bits DOS1 and DOS0; note 1
DOS1
DOS0
MODE
DESCRIPTION
0
0
1
1
0
1
0
1
Outsel
Tuner
Ext1
Decoder output selection is set by output select function [por].
Tuner input is directly connected to decoder output.
Ext1 input is directly connected to decoder output.
Ext3 is directly connected to decoder output.
Ext3
Note
1. With the decoder output select some special connections can be made overruling the output select (OSL, OSR and
OSN), e.g. for connecting a decoder box to the VCR.
6.9
Left/Right (L/R) volume byte
Table 24 Bits of Left/Right volume byte
BIT
DESCRIPTION
VLM
Volume Left Mute; see Table 25
Volume Left 5 to Volume Left 0; see Table 25
VL5 to VL0
VRM
Volume Right Mute; see Table 25
VR5 to VR0
Volume Right 5 to Volume Right 0; see Table 25
Table 25 Left/Right volume byte; notes 1 and 2
VLM
VL5
VL4
VL3
VL2
VL1
VL0
MODE
VRM
1
VR5
X
0
VR4
X
0
VR3
X
0
VR2
X
0
VR1
X
0
VR0
X
0
mute
0
−49 dB
−48 dB
−47 dB
−46 dB
−45 dB
−44 dB
−43 dB
−42 dB
−41 dB
−40 dB
−39 dB
−38 dB
−37 dB
−36 dB
−35 dB
−34 dB
−33 dB
−32 dB
−31 dB
0
0
0
0
0
0
1
0
0
0
0
0
1
0
0
0
0
0
0
1
1
0
0
0
0
1
0
0
0
0
0
0
1
0
1
0
0
0
0
1
1
0
0
0
0
0
1
1
1
0
0
0
1
0
0
0
0
0
0
1
0
0
1
0
0
0
1
0
1
0
0
0
0
1
0
1
1
0
0
0
1
1
0
0
0
0
0
1
1
0
1
0
0
0
1
1
1
0
0
0
0
1
1
1
1
0
0
1
0
0
0
0
0
0
1
0
0
0
1
0
0
1
0
0
1
0
1995 Mar 21
20
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
VLM
VL5
VL4
VL3
VL2
VL1
VL0
MODE
VRM
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
VR5
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
VR4
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
VR3
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
VR2
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
VR1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
VR0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
−30 dB
−29 dB
−28 dB
−27 dB
−26 dB
−25 dB
−24 dB
−23 dB
−22 dB
−21 dB
−20 dB
−19 dB
−18 dB
−17 dB
−16 dB
−15 dB
−14 dB
−13 dB
−12 dB
−11 dB
−10 dB
−9 dB
−8 dB
−7 dB
−6 dB
−5 dB
−4 dB
−3 dB
−2 dB
−1 dB
0 dB [por]
1 dB
2 dB
3 dB
4 dB
5 dB
6 dB
7 dB
8 dB
1995 Mar 21
21
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
VLM
VL5
VL4
VL3
VL2
VL1
VL0
MODE
VRM
VR5
1
VR4
1
VR3
1
VR2
0
VR1
1
VR0
0
0
0
0
0
0
0
9 dB
10 dB
11 dB
12 dB
13 dB
14 dB
1
1
1
0
1
1
1
1
1
1
0
0
1
1
1
1
0
1
1
1
1
1
1
0
1
1
1
1
1
1
Notes
1. X = don’t care.
2. Optimum mute performance is achieved by combination of the mute bit (VLM and/or VRM) with the smallest volume
setting (Vx5 to Vx0 = ‘000000’).
6.10 Headphone volume byte
Table 26 Bits of Left/Right volume byte
BIT
DESCRIPTION
Volume Headphone Mute; see Table 27
Volume Headphone 5 to Volume Headphone 0; see Table 27
VHM
VH5 to VH0
Table 27 Headphone volume byte; notes 1 and 2
VHM
1
VH5
X
0
VH4
X
0
VH3
X
0
VH2
X
0
VH1
X
0
VH0
X
0
MODE
mute
0
−47 dB
−46 dB
−45 dB
−44 dB
−43 dB
−42 dB
−41 dB
−40 dB
−39 dB
−38 dB
−37 dB
−36 dB
−35 dB
−34 dB
−33 dB
−32 dB
−31 dB
−30 dB
−29 dB
0
0
0
0
0
0
1
0
0
0
0
0
1
0
0
0
0
0
0
1
1
0
0
0
0
1
0
0
0
0
0
0
1
0
1
0
0
0
0
1
1
0
0
0
0
0
1
1
1
0
0
0
1
0
0
0
0
0
0
1
0
0
1
0
0
0
1
0
1
0
0
0
0
1
0
1
1
0
0
0
1
1
0
0
0
0
0
1
1
0
1
0
0
0
1
1
1
0
0
0
0
1
1
1
1
0
0
1
0
0
0
0
0
0
1
0
0
0
1
0
0
1
0
0
1
0
1995 Mar 21
22
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
VHM
VH5
VH4
VH3
VH2
VH1
VH0
MODE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
−28 dB
−27 dB
−26 dB
−25 dB
−24 dB
−23 dB
−22 dB
−21 dB
−20 dB
−19 dB
−18 dB
−17 dB
−16 dB
−15 dB
−14 dB
−13 dB
−12 dB
−11 dB
−10 dB
−9 dB
−8 dB
−7 dB
−6 dB
−5 dB
−4 dB
−3 dB
−2 dB
−1 dB
0 dB [por]
1 dB
2 dB
3 dB
4 dB
5 dB
6 dB
7 dB
8 dB
9 dB
10 dB
11 dB
12 dB
1995 Mar 21
23
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
VHM
VH5
VH4
VH3
VH2
VH1
VH0
MODE
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
1
1
0
1
0
1
13 dB
14 dB
15 dB
16 dB
Notes
1. X = don’t care.
2. Optimum mute performance is achieved by combination of the mute bit (VHM) with the smallest volume setting
(VH5 to VH0 = ‘000000’).
6.11 Install byte
Table 28 Bits of install byte
BIT
DEV1 and DEV0
NPL3 to NPL0
AUTN
DESCRIPTION
Deviation 1 and Deviation 0; see Table 29
Normal Playback Level 3 to Normal Playback Level 0; see Table 30
Auto Normal; see Table 31
DOC
Drop-out Cancellation; see Table 32
Table 29 Bits DEV1 and DEV0; note 1
DEV1
DEV0
MODE
DESCRIPTION
0
0
56 kHz
deviation of modem set to 56 kHz (equals 50 kHz; −10 dBV);
1 kHz audio
0
1
1
1
0
1
50 kHz
45 kHz
40 kHz
deviation of modem set to 50 kHz (equals 50 kHz; −8 dBV);
1 kHz audio
deviation of modem set to 45 kHz (equals 50 kHz; −6 dBV);
1 kHz audio
deviation of modem set to 40 kHz (equals 50 kHz; −4 dBV);
1 kHz audio
Note
1. A selection of four different settings of FM deviation/audio level can be made for the audio FM circuit.
1995 Mar 21
24
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
Table 30 Normal Playback Level bits; note 1
NPL3
NPL2
NPL1
NPL0
MODE
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
−7 dB
−6 dB
−5 dB
−4 dB
−3 dB
−2 dB
−1 dB
0 dB [por]
1 dB
2 dB
3 dB
4 dB
5 dB
6 dB
7 dB
8 dB
Note
1. A selection of 16 settings of amplification in the linear audio playback amplifier can be made. This can be used for
adjustment purposes or as a fixed setting.
Table 31 Bit AUTN; note 1
AUTN
MODE
DESCRIPTION
0
−
Audio FM signal is muted, when no hi-fi tracks are found in
playback [por].
1
auto normal
Output select is switched to normal, when no hi-fi tracks are found in
playback.
Note
1. When the audio FM circuit is in playback and there is no FM input signal (playback of a conventional recording) the
audio FM circuitry is muted. If this situation occurs and AUTN = 1 the selections stereo, left or right in the output
select (OSR, OSL and OSN) are overridden and the selection normal is made. This means that linear audio is the
output signal for as long as the internal playback mute is active. The status of this internal mute signal can be read
by bit PAFM (see Section 6.13).
Table 32 Bit DOC
DOC
MODE
drop-out cancel(1)
DESCRIPTION
0
1
−
−
audibility of short drop-outs is minimized [por]
Note
1. When DOC = 1 an additional sample-and-hold circuit is activated during drop-outs in the FM input signal, minimizing
their audibility.
1995 Mar 21
25
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
6.12 Test byte
Table 33 Bits of test byte
BIT
DESCRIPTION
STBY
Standby; see Table 34
CALS
Calibration Start; see Table 35
AGC Not; see Table 36
AGCN
TST4 to TST0
Test 4 to Test 0; see Table 37
Table 34 Bit STBY
STBY
MODE
DESCRIPTION
0
1
−
normal operation [por]
standby mode (low power consumption)
standby(1)
Note
1. When STBY = 1 the IC is partly switched off to minimize its power consumption. The I2C-bus and the direct
connections between inputs and outputs (selectable with bits: LOS1, LOS0, DOS1 and DOS0) are still operable in
standby mode.
Table 35 Bit CALS
CALS
MODE
auto-calibrate(1)
DESCRIPTION
0
1
−
[por]
oscillators and BPFs are automatically calibrated
Note
1. When CALS is made logic 1 after being logic 0 the IC performs an automatic frequency calibration of the modem
CCOs and the built-in bandpass filters (BPFs). During calibration, the IC should be in record or loop-through mode.
The calibration takes <500 ms and uses the HID input (25 Hz in PAL mode or 30 Hz in NTSC mode) as the reference
frequency. The bit CALR (see Section 6.13) can be read to check if the calibration has been completed successfully.
Table 36 Bit AGCN; note 1
AGCN
MODE
AGC on
AGC off
DESCRIPTION
linear audio record; AGC active [por]
linear audio record; AGC inactive
0
1
Note
1. With bit AGCN the linear audio record AGC can be switched (off and on).
1995 Mar 21
26
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
Table 37 Test bits TST4 to TST0; note 1
TST4
TST3
TST2
TST1
TST0
MODE
DESCRIPTION
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
1
0
1
−
[por]
VCO test L
VCO test R
BPF test L
in record mode: only 1.4 or 1.3 MHz at FMOUT
in record mode: only 1.8 or 1.7 MHz at FMOUT
in playback mode: only left BPF at FMOUT;
HF AGC switched off
0
0
1
0
0
BPF test R
in playback mode: only right BPF at FMOUT;
HF AGC switched off
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Test
Test
Test
Test
Test
Test
Test
Test
Test
Test
Test
Test
Test
Test
Test
Test
Test
Test
Test
Test
Test
Test
Test
Test
Test
Test
EQ set(2)
not for application
not for application
not for application
not for application
not for application
not for application
not for application
not for application
not for application
not for application
not for application
not for application
not for application
not for application
not for application
not for application
not for application
not for application
not for application
not for application
not for application
not for application
not for application
not for application
not for application
not for application
linear audio playback equalization using
non-standard settings
Notes
1. The bits TST4 to TST0 are used for testing and measurement purposes.
2. Test number 31 (TST4 to TST0 = 11111) is a special setting which can be used to change the internal linear audio
playback equalization to non-standard settings as shown in Table 38.
1995 Mar 21
27
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
Table 38 Linear audio playback equalization non-standard settings
SETTING
MODE
TEST NUMBER 31
Standard play (LP = 0)
3180 and 120 µs
2544 and 96 µs
3180 and 170 µs
2731 and 146 µs
not selected
selected
Long play (LP = 1)
not selected
selected
6.13 Read byte
Table 39 Bits of read byte
BIT
DESCRIPTION
CALR
PAFM
POR
Calibration ready; see Table 40
Playback Audio FM Mute; see Table 41
Power-On reset; see Table 42
Table 40 Bit CALR; note 1
CALR
MODE
DESCRIPTION
0
1
not calibrated
calibrated
IC has not been auto-calibrated [por].
IC has been calibrated successfully.
Note
1. If CALR = 0, bandpass filters and oscillators have not been calibrated successfully. When an automatic calibration
is started by bit CALS, the end of the calibration cycle can be checked via this bit. If for some reason a successful
calibration can not be made within the available adjustment range, e.g. if no HID signal is available, CALR will remain
logic 0. After calibration the adjustment will be held for as long as the digital supply voltage (VDDD) is available.
Table 41 Bit PAFM; note 1
PAFM
MODE
AFM available
no AFM carrier
DESCRIPTION
0
1
Audio FM signal is detected at FM input.
No audio FM signal detected; hi-fi processing is muted.
Note
1. When the hi-fi processing is in playback mode but no Audio FM input signal is found, the IC generates an internal
mute signal which mutes the noise signal coming from the demodulators. The status of this mute signal can be read
via bit PAFM. This signal however is only valid with the hi-fi circuit in playback (RAF = 0 and IPAF = 0).
Table 42 Bit POR; note 1
POR
MODE
DESCRIPTION
0
1
−
−
POR generated
POR pulse is generated since last read.
Note
1. When the IC is switched on, or a power dip occurs on the digital supply (VDDD) line, a Power-on Reset signal is
generated which resets the IC's I2C-bus registers and the auto-calibration circuit. If such a situation has occurred
after the last time the read byte has been read, bit POR = 1. After reading the read byte POR is reset to logic 0.
1995 Mar 21
28
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
7
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 134).
SYMBOL
PARAMETER
analog supply voltage 1
CONDITIONS
MIN.
MAX.
13.2
UNIT
VDDA1
VDDA2
VDDD
Vn
0
0
0
V
analog supply voltage 2
digital supply voltage
voltage on pins:
5.5
5.5
V
V
1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 28, 41, 44, 51, 52,
63 and 64
0
7.7
V
56, 60 and 62
0
0
VDDA2
VDDD
+150
+70
V
12 and 32
V
Tstg
Tamb
Ves
storage temperature
operating ambient temperature
electrostatic handling
−65
0
°C
°C
V
MM; note 1
−150
−1500
+150
+1500
HBM; note 2
V
Notes
1. Machine Model (MM).
2. Human Body Model (HBM).
8
THERMAL CHARACTERISTICS
SYMBOL
PARAMETER
VALUE
55
UNIT
Rth j-a
thermal resistance from junction to ambient in free air
K/W
9
DC CHARACTERISTICS
VDDA1 = 12 V; VDDA2 = 5 V; VDDD = 5 V; NTSC = 0; LP = 0; CALR = 1; Tamb = 25 °C;
all volume control levels set to 0 dB; measured in test circuit (see Fig.13); unless otherwise specified.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP.
MAX.
UNIT
Supply voltages
VDDA1
VDDA2
VDDD
analog supply voltage 1; pin 50
analog supply voltage 2; pin 58
digital supply voltage; pin 13
10.5
12
5
13.2
V
V
V
4.75
4.75
5.5
5.5
5
Supply currents
IDDA1
analog supply current 1; pin 50
analog supply current 2; pin 58
operating
−
−
−
−
−
−
−
47
28
7
60
35
9
mA
mA
mA
mA
mA
mA
mA
standby
IDDA2
record(1); LT(2)
playback(3)
standby; LT(2)
operating
18
3
23
5
IDDD
digital supply current; pin 13
1
3
standby
1
3
1995 Mar 21
29
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP.
MAX.
UNIT
Input voltages
VI
DC input voltage; pins 1, 2, 3, 4, 5,
6, 7, 8, 9, 10, 11, 28, 31, 34, 35
and 36
−
3.8
−
V
V57
DC input voltage internally
generated; pin 57
−
−
−
−
1.9
0
−
−
−
−
V
V
V
V
V30
DC input voltage internally
generated; pin 30
V51,64
V52,63
DC input voltage internally
generated; pins 51 and 64
playback(3)
3.8
3.8
DC input voltage internally
generated; pins 52 and 63
record(1); LT(2)
Output voltages
VO
DC output voltage:
pins 19, 20, 21, 22 and 33
pins 25 and 26
pins 18, 29, 42, 53 and 59
pin 56
−
−
−
−
−
−
−
−
6
−
−
−
−
−
−
−
−
V
V
V
V
V
V
V
V
5.5
3.8
1.2
1.2
0.6
4.3
3.3
record(1)
playback(3); LT(2)
pin 56
pin 55
pins 51 and 64
pins 52 and 63
record(1); LT(2)
playback(3)
Head identification pulse input (HID; pin 61)
VIH
VIL
HIGH level input voltage
LOW level input voltage
2.75
0
−
−
5.50
2.25
V
V
Normal record pin (LINREC; pin 32)
VOH
VOL
HIGH level output voltage
LOW level output voltage
IL = −500 µA
IL = 500 µA
V
DDD − 0.5
−
−
−
V
V
−
0.5
I/O RAF (pin 12)
USED AS OUTPUT
VOH
HIGH level output voltage
LOW level output voltage
RAF = 1;
IL = −35 µA
V
DDD − 0.25 −
VDDD
0.4
−
V
VOL
IOH
IOL
RAF = 0;
IL = 185 µA
0
−
−
−
V
HIGH level output current
(drive capability)
RAF = 1
RAF = 0
−35
185
µA
µA
LOW level output current
(drive capability)
−
1995 Mar 21
30
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP.
MAX.
UNIT
USED AS INPUT (OUTPUT OVERRULED)
VIH
VIL
IIH
HIGH level input voltage
LOW level input voltage
HIGH level input current
LOW level input current
3.5
0
−
−
−
−
VDDD
V
1.5
V
at VIH
at VIL
−
345
−65
µA
µA
IIL
−
Notes
1. Record: record audio FM and record linear audio.
2. Loop-through: loop-through audio FM and loop-through R linear audio.
3. Playback: playback audio FM and playback linear audio.
10 AC CHARACTERISTICS
10.1 Record audio FM mode
Audio input signal −8 dBV from TUNL and TUNR (pins 2 and 3); VDDA1 = 12 V; VDDA2 = 5 V; VDDD = 5 V; NTSC = 0;
LP = 0; CALR = 1; f = 1 kHz (audio test frequency); Tamb = 25 °C; all volume control levels set to 0 dB; measured in test
circuit (see Fig.13); unless otherwise specified.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP.
MAX.
UNIT
Audio inputs (SAP, TUNL, TUNR, CINL, CINR, EXT1L, EXT1R, EXT2L, EXT2R, EXT3L and EXT3R;
pins 1, 2, 3, 4, 5, 6, 7, 8, 9, 10 and 11)
Ri
input resistance
100
130
−
kΩ
ViAF
audio input voltage
−
−
8
dBV
Line and decoder outputs (LINEL, LINER, LINE2L and LINE2R; pins 21, 22, 19 and 20)
Vo(max)
maximum output voltage
−9
−8
−7
dBV
dBV
THD = 1%; RL = 5 kΩ;
CL = 2.2 nF;
10
11
−
TUNL ≤ −3 dBV;
TUNR ≤ −3 dBV; note 1
Ro
output resistance
total harmonic distortion
noise level
−
−
−
200
0.01
−91
275
0.1
Ω
THD
Vn
%
fi = 300 Hz to 20 kHz;
TUNL and TUNR
AC grounded
−87
dBV
αcb
channel balance
−1
−
0
+1
dB
Vmute
αct
volume mute level
−100
−83
−0.1
−12
−80
−78
+0.5
−5
dBV
dBV
dB
crosstalk between channels
one channel driven
fi = 20 kHz
−
fres
frequency response with
respect to 1 kHz; low-pass
filter transfer
−0.5
−
fi = 60 kHz
dB
αct(max)
maximum audio input crosstalk −8 dBV at a not selected
−
−90
−
dBV
stereo audio input
1995 Mar 21
31
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP.
MAX.
UNIT
VU meter drive (DCOUTL and DCOUTR; pins 23 and 24); square root of output voltage (see Fig.7)
Vo
Ro
Vo
output voltage
1.69
1.8
100
−
1.91
−
V
Ω
V
output resistance
−
output voltage at maximum
record level
TUNL = −3 dBV;
TUNR = −3 dBV; note 1
V
DDD − 0
VDDD
.5
Voz
output voltage for zero-level
input
−
−
−
300
mV
dB
αcb
channel balance
−0.11
+0.11
RF converter drive output; mono RFCOUT; pin 18 (see Fig.8)
Vo
output voltage
−9
−
−8
−7
−
dBV
Ω
Ro
output resistance
total harmonic distortion
100
0.01
−3
THD
Vo
−
−
%
output voltage at maximum
record level
TUNL = −3 dBV;
TUNR = −3 dBV; note 1
−5
−1
dBV
THD
total harmonic distortion at
maximum record level
TUNL = −3 dBV;
TUNR = −3 dBV; note 1
−
0.3
−
%
Headphone outputs (HPOUTL and HPOUTR; pins 25 and 26); headphone volume set to 0 dB
Vo
output voltage
−9
−
−8
−7
−
dBV
Ω
Ro
output resistance
1
THD
Vo(max)
total harmonic distortion
maximum output voltage
−
0.01
9.5
0.1
−
%
THD = 1%;
9.0
dBV
TUNL ≤ −3 dBV;
TUNR ≤ −3 dBV;
RL = 250 Ω; note 1
Vn
noise level
fi = 300 Hz to 20 kHz;
tuner AC grounded
−
−90
−80
dBV
αct
crosstalk between channels
headphone volume mute level
channel balance
one channel driven
−
−83
−90
−
−70
−70
+1
dBV
dBV
dB
Vmute
αcb
−
−1
1995 Mar 21
32
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP.
MAX.
UNIT
Audio outputs (AFNL and AFNR; pins 64 and 51); audio output from noise reduction
VoAF
THD
VoAF
audio output voltage
−12.5
−
−11.5
0.12
−2
−10.5
dBV
total harmonic distortion
0.3
%
audio output voltage at
maximum record level
TUNL = −3 dBV;
TUNR = −3 dBV; note 1
−3.5
−0.5
dBV
THD
Vn
total harmonic distortion at
maximum record level
TUNL = −3 dBV;
TUNR = −3 dBV; note 1
−
−
0.2
3
%
noise level
fi = 300 Hz to 20 kHz;
tuner AC grounded
−54
−52
dBV
αcb
L
channel balance
linearity
−1
28.5
−
−
+1
31.5
−50
−
dB
Vi = −8 to −68 dBV
30
dB
αcc
tatt
channel crosstalk
attack time according VHS
recovery time according VHS
mute level
one channel driven
−58
5
dBV
ms
ms
dBV
dB
−
trec
Vmute
−
70
−
MUTE = 1
fi = 300 Hz
fi = 10 kHz
−
−52
−0.2
3.9
−
frequency response with
respect to 1 kHz; output level
−0.9
2.9
+0.5
4.9
dB
FM modulator (audio input from AFML and AFMR; pins 63 and 52)
THD
total harmonic distortion
FM frequency deviation
∆f = 50 kHz
−
0.1
50
0.2
55
%
∆f
ViAF = −11.5 dBV;
45
kHz
NTSC = 0
ViAF = −11.5 dBV;
NTSC = 1
45
50
50
55
kHz
kHz
audio input signal from NR 44.5
outputs AFNL and AFNR;
NTSC = 0
56.1
audio input signal from NR 44.5
outputs AFNL and AFNR;
NTSC = 1
50
56.1
kHz
∆fmax
maximum FM frequency
deviation
140
150
160
1405
1305
−
kHz
kHz
kHz
kHz
foL
FM centre frequency left
f = 1.4 MHz; NTSC = 0;
calibrated in PAL mode
1395
1295
−
1400
1300
1300
f = 1.3 MHz; NTSC = 1;
calibrated in NTSC mode
NTSC = 1; calibrated in
PAL mode
1995 Mar 21
33
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
SYMBOL
foR
PARAMETER
CONDITIONS
MIN
1795
TYP.
1800
MAX.
1805
UNIT
kHz
FM centre frequency right
f = 1.8 MHz; NTSC = 0;
calibrated in PAL mode
f = 1.7 MHz; NTSC = 1;
calibrated in NTSC mode
1695
1700
1700
±50
1705
kHz
NTSC = 1; calibrated in
PAL mode
−
−
−
−
kHz
TC
temperature coefficient
10−6/K
HF output stage (FMOUT; pin 56)
VoR(p-p)
right output voltage
(peak-to-peak value)
foR = 1.8 MHz;
1st harmonic
455
455
152
152
2.7
510
510
170
170
3
572
572
190
190
3.3
mV
mV
mV
mV
foR = 1.7 MHz;
1st harmonic
VoL(p-p)
left output voltage
(peak-to-peak value)
foL = 1.4 MHz;
1st harmonic
foL = 1.3 MHz;
1st harmonic
ratio of output voltages
VoR
---------
VoL
α3rd
3rd harmonic suppression
output resistance
NTSC = 0
NTSC = 1
20
18
−
30
−
dB
dB
Ω
28
−
Ro
100
130
Note
1. Record volume control for left and right channel set to maximum (+14 dB). Headphone volume control at 0 dB.
10.2 Record linear audio mode
Audio input signal −8 dBV from SAP, TUNL and TUNR (pins 1, 2 and 3); NormSel is input; OutSel is normal.
SYMBOL
Linear audio playback input; PBIN (pin 34)
Zi input impedance
Linear audio EQSW input (pin 30)
Zi input impedance
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
IL = ±1 mA
−
7
15
Ω
LP = 0
LP = 1
100
150
15
−
kΩ
−
30
Ω
Line output (pins 21 and 22)
Vo
output voltage
AGCN = 0; note 1
−8
−6
−8
−4
−6
dBV
dBv
AGCN = 1;
−10
NormSel = volume; note 1
αct
crosstalk (linear to stereo)
OutSel = stereo;
−
−88
−80
dBV
NormSel = SAP; TUNL
and TUNR AC grounded
1995 Mar 21
34
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Linear audio record output RECOUT; pin 33 (see Fig.11)
Vo
output voltage
AGCN = 0; note 1
−2
0
+2
dBV
AGCN = 1;
−4
−2
0
dBv
NormSel = volume; note 1
THD
Vn
total harmonic distortion
noise level
AGCN = 1;
NormSel = volume
−
0.02
−80
0.5
−70
%
AGCN = 1; TUNL and
TUNR AC grounded
−
dBV
Zo
output impedance
mute level
−
−
100
200
Ω
Vmute
loop-through R;
NOM = mute
−85
−
dBV
Linear audio RECEQ (pin 31)
Zt
transfer impedance
note 2
900
1200
1500
Ω
Notes
1. Using AGC on (AGCN = 0) and NormSel set to volume mode. The AGC gain is 1 dB higher for audio signals below
the AGC clip level (specified value of AGC clip level does not change).
Using AGC off (AGCN = 1) and NormSel not set to volume mode, the output signal is 1 dB lower (1 dB below the
specified value).
(R + Z)
2. The transfer A of the REC equalizer from LININ to RECOUT is: A =
× 3.98
--------------------
Z
where Z is the (complex) impedance at pin RECEQ to ground and R is the specified resistance of 1200 Ω.
10.3 Playback Audio FM mode
Audio output signal from the FM (de)modulator at AFML and AFMR (pins 63 and 52).
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP.
MAX.
UNIT
Bandpass filters (filter curves measured using test numbers 3 and 4 [HF AGC off])
Vo(rms)
output voltage level at FMOUT ViHF(rms) = 30 mV;
105
105
105
105
150
215
mV
(RMS value)
1.3 MHz BPF
ViHF(rms) = 30 mV;
1.4 MHz BPF
150
150
150
215
215
215
mV
mV
mV
ViHF(rms) = 30 mV;
1.7 MHz BPF
ViHF(rms) = 30 mV;
1.8 MHz BPF
1.4 MHz BPF
1.0 MHz/1.4 MHz
1.25 MHz/1.4 MHz
1.55 MHz/1.4 MHz
1.65 MHz/1.4 MHz
1.55 MHz/1.65 MHz
1.8 MHz/1.4 MHz
−
−30
−3
−3
−17
15
−
−20
−
dB
dB
dB
dB
dB
dB
−6
−7
−
−
−12
−
10
−
−30
1995 Mar 21
35
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
SYMBOL
PARAMETER
1.8 MHz BPF
CONDITIONS
MIN
TYP.
MAX.
−30
UNIT
dB
1.4 MHz/1.8 MHz
1.55 MHz/1.8 MHz
1.65 MHz/1.8 MHz
1.95 MHz/1.8 MHz
2.2 MHz/1.8 MHz
1.45 MHz/1.3 MHz
1.55 MHz/1.3 MHz
1.45 MHz/1.55 MHz
1.45 MHz/1.7 MHz
1.55 MHz/1.7 MHz
1.55 MHz/1.45 MHz
Tamb = 0 to 70 °C
−
−
−
−17
−3
−10
−
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
kHz
−7
−3
0
−
−25
−3
−15
−
1.3 MHz BPF
1.7 MHz BPF
−7
−
−17
15
−12
−
10
−
−17
−3
−10
−
−7
10
−
15
−
fshift
frequency shift of BPF curve
with temperature
10
−
HF AGC
Vi max(p-p)
maximum input signal level
(peak-to-peak value)
1.4 and 1.8 MHz carrier
added
−
−
1.25
28
V
VoL(rms)
VoR(rms)
B
left BPF output voltage level
(RMS value)
fi = 1.4 MHz at FMIN;
ViHF(rms) = 4 mV
13
84
84
13
84
84
−
19
mV
mV
mV
mV
mV
mV
kHz
fi = 1.4 MHz at FMIN;
ViHF(rms) = 25 mV
120
120
19
170
170
28
fi = 1.4 MHz at FMIN;
ViHF(rms) = 125 mV
right BPF output voltage level fi = 1.8 MHz at FMIN;
(RMS value)
ViHF(rms) = 4 mV
fi = 1.8 MHz at FMIN;
ViHF(rms) = 25 mV
120
120
10
170
170
−
fi = 1.8 MHz at FMIN;
ViHF(rms) = 125 mV
−3 dB bandwidth
ViHF(rms) = 75 mV;
1.4 MHz carrier
PLL FM demodulator and limiter
αAM
AM rejection
ViHF(rms) = 2 to 200 mV;
m = 30%
−
−
−70
−
dBV
mV
Vi(rms)
THD
sensitivity; PLL locked
(RMS value)
∆f = 150 kHz;
S/N = 35 dB (audio)
0.6
1.25
total harmonic distortion
∆f = 50 kHz
−
−
0.03
0.2
57
0.3
1.5
−
%
∆f = 150 kHz
%
S/N
VoAF
Vstep
αct
signal-to-noise ratio
AF output voltage
ViHF = 30 mV; ∆f = 50 kHz 54
dB
∆f = 50 kHz
note 1
−12.5
−11.5
−
−10.5
−48
−
dBV
dBV
dBV
step response
−
−
crosstalk between channels
L to R; R to L
−90
1995 Mar 21
36
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP.
MAX.
UNIT
Sample-and-hold (see Fig.9)
th
hold time pulse width
audio distortion
5
−
−
6
7
µs
dAF
td
note 2
−
−75
dB
delay from HID pulse to hold
pulse
0.4
−
µs
Drop-Out Cancellation (DOC)
DOC activation level w.r.t.
−7
−4
−2
dB
mute activation level
td(off)
switch-off delay time
no signal to signal
5
9
14
µs
Mute timing (CMUTE; pin 62)
Vi(rms)
mute activation level
(RMS value) referenced to
FMIN
2.2
4.2
7.1
mV
td(off)
td(on)
switch-off delay time
switch-on delay time
signal to no signal
no signal to signal
−
−
15
−
−
ms
ms
400
Level detector output ENVOUT; pin 60 (see Fig.10)
Vo
output voltage level
fi (FMIN) = 1.4 MHz;
iHF(rms) = 2 mV
0.6
2.5
4.1
−
0.9
2.9
4.5
33
1.2
3.3
4.8
−
V
V
fi (FMIN) = 1.4 MHz;
ViHF(rms) = 20 mV
V
fi (FMIN) = 1.4 MHz;
ViHF(rms) = 200 mV
V
Ro
output resistance
kΩ
Line outputs (LINEL and LINER; pins 27 and 28); audio inputs at AFNL and AFNR (pins 64 and 51): −11.5 dBV
Vo
output voltage
−10
−10
−8
−8
−6
−6
dBV
dBV
input signal from modem
to AFML and AFMR
Vn
noise level
fi = 300 Hz to 20 kHz
−
−
−98
0.05
60
−90
0.2
dBV
%
THD
L
total harmonic distortion
linearity
ViAF = −11.5 to −41.5 dBV 58
−2
62
dB
dB
dB
dB
αcb
fres
channel balance
0
+2
frequency response with
respect to 1 kHz; output level
fi = 300 Hz
fi = 10 kHz
−1
+0.4
−7.7
+1.8
−5.7
−9.7
Notes
1. HID pulse frequency set to 1 kHz. Unmodulated carrier at FMIN input with 135° phase step.
2. The audio distortion is measured with the HID pulse frequency set to 1 kHz (fi = 500 Hz). FM signal: fm = 10 kHz;
∆f = 50 kHz. The distortion is measured with a 3 kHz 4th-order low-pass filter. The measured value at 1 kHz
HID-pulse frequency is corrected with 26 dB in order to calculate the equivalent distortion at 50 Hz HID-pulse
frequency.
1995 Mar 21
37
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
10.4 Playback linear audio
Audio input signal −68 dBV from PBIN (pin 34).
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP.
MAX.
UNIT
Linear audio playback input PBIN (pin 34)
Zi
input impedance
60
100
−
kΩ
Vo
output voltage at LINOUT
−14
−12
−10
dBV
Linear audio RESSW input (pin 35)
Z
impedance between RESSW
and PBIN
LP = 0
LP = 1
−
50
100
Ω
100
150
−
kΩ
Line outputs LINEL and LINER (pins 21 and 22)
Vo
output voltage
LP = 0
LP = 1
−8
−6.7
7.2
−5.4
5.9
−3.7
−
−6
−4
dBV
dBV
dB
−4.7
8.2
−2.7
9.2
−3.4
7.9
−1.7
0.5
−
fres
frequency response with
respect to 1 kHz; output level
fi = 315 Hz; LP = 0
fi = 10 kHz; LP = 0
fi = 315 Hz; LP = 1
fi = 10 kHz; LP = 1
−4.4
6.9
dB
dB
−2.7
0.05
10
dB
THD
Vo(max)
Vn
total harmonic distortion
maximum output voltage
noise level
%
THD = 1%
−
dBV
dBV
dBV
fi = 300 Hz to 20 kHz
referenced to PBIN
−
−58
−120
−55
−
−
MKA363
MKA362
1.5
1.5
V
V
iAF
oAF
(dBV)
(dBV)
11.5
11.5
21.5
31.5
41.5
21.5
31.5
41.5
68
48
28
8
12
68
48
28
8
12
V
(dBV)
V
(dBV)
o
iAF
Fig.5 Compression curve of noise reduction at
1 kHz; record mode. The audio output
voltage at AFNL and AFNR
Fig.6 Expansion curve of noise reduction at
1 kHz; playback mode. The audio output
voltage at LINEL and LINER
(pins 64 and 51) as a function of the
audio input voltage at TUNL and TUNR
(pins 2 and 3).
(pins 21 and 22) as a function of the audio
input voltage at AFNL and AFNR
(pins 64 and 51).
1995 Mar 21
38
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
MKA364
MGC418
5
0
handbook, halfpage
DCOUTL/R = 2.86 x audio level
V
V
o
o
(V)
(dBV)
5
4
3
2
1
0
10
15
20
58
58
38
18
2
22
38
18
2
22
V
o
(dBV)
V
o
(dBV)
Fig.7 VU meter output voltage at
Fig.8 RF converter output voltage at RFCOUT
(pin 18) as a function of line output signal
level at LINEL and LINER (pins 21 and 22).
DCOUTL and DCOUTR (pins 23 and 24)
as a function of audio signal level.
MBE282
5
MKA366 - 1
handbook, halfpage
HID
V
o
INPUT
(V)
4
3
2
1
0
time
sample-and-
hold
CONTROL
hold
track
time
t
h
1
2
3
10
1
10
10
10
(mV)
t
d
V
iHF
Fig.10 Level detector output voltage at ENVOUT
(pin 60) as a function of the 1.4 MHz carrier
input voltage level (RMS value) at FMIN
(pin 57).
Fig.9 Sample-and-hold timing waveforms.
1995 Mar 21
39
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
MBE283
10
4
RECOUT
(dBV)
LINE
(dBV)
6
0
(1)
(2)
4
2
0
2
8
6
12
16
20
24
10
14
18
20
16
12
8
4
0
4
8
V (dBV)
i
(1) Normsel = volume; AGCN = 1.
(2) Normsel ≠ volume; AGCN = 0.
Fig.11 RECOUT/LINE output as a function of audio signal level (hi-fi inputs).
MBE280
handbook, halfpage
LINREC
output
time
PBIN
impedance
HIGH
LOW
time
t
t
d
d
Fig.12 Timing of LINREC output versus PBIN
impedance.
1995 Mar 21
40
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
11 INTERNAL CIRCUITRY
SYMBOL
PIN
EQUIVALENT CIRCUIT
DESCRIPTION
SAP
1
Second Audio Program (SAP)
input.
78 kΩ
1
52 kΩ
3.8 V
MLD008
TUNL
TUNR
2
3
Left channel tuner input.
65 kΩ
13 kΩ
2
52 kΩ
3.8 V
MLD009
Right channel tuner input.
65 kΩ
13 kΩ
3
52 kΩ
3.8 V
MLD010
CINL
4
5
6
Left channel cinch input.
Right channel cinch input.
Left channel external 1 input.
78 kΩ
4
52 kΩ
3.8 V
MLD011
CINR
EXT1L
78 kΩ
5
52 kΩ
3.8 V
MLD012
65 kΩ
13 kΩ
6
52 kΩ
3.8 V
MLD013
EXT1R
7
Right channel external 1 input.
65 kΩ
13 kΩ
7
52 kΩ
3.8 V
MLD014
1995 Mar 21
41
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
SYMBOL
PIN
EQUIVALENT CIRCUIT
DESCRIPTION
EXT2L
8
Left channel external 2 input.
65 kΩ
65 kΩ
65 kΩ
65 kΩ
13 kΩ
13 kΩ
13 kΩ
13 kΩ
8
52 kΩ
3.8 V
MLD015
MLD016
MLD017
MLD018
EXT2R
EXT3L
EXT3R
RAF
9
Right channel external 2 input.
Left channel external 3 input.
Right channel external 3 input.
9
52 kΩ
3.8 V
10
11
12
10
52 kΩ
3.8 V
11
52 kΩ
3.8 V
Record/playback switch drive
output for head amplifier control or
input for overruling the I2C-bit RAF.
2
1
3
12
275
Ω
100 µA
RAF
2
I
C-RAF
1
MLD019
VDDD
13
Digital supply voltage for I2C-bus
(+5 V).
1995 Mar 21
42
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
SYMBOL
PIN
EQUIVALENT CIRCUIT
DESCRIPTION
SDA
14
Data input/output for I2C-bus.
275 Ω
14
MLD020
SCL
15
Clock input for I2C-bus.
275 Ω
15
MLD021
VSSD
16
17
Digital ground for I2C-bus.
RFCAGC
RF converter AGC-time constant.
100 Ω
17
MLD022
RFCOUT
18
RF converter drive output.
18
250 µA
MLD023
1995 Mar 21
43
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
SYMBOL
PIN
EQUIVALENT CIRCUIT
DESCRIPTION
LINE2L
19
Line 2 left output (e.g. decoder
output).
200 Ω
19
5.8 kΩ
5.8 kΩ
5.8 kΩ
5.8 kΩ
MLD024
LINE2R
20
Line 2 right output (e.g. decoder
output).
200 Ω
20
5.8 kΩ
MLD025
LINEL
21
Line output left.
200 Ω
21
5.8 kΩ
MLD026
1995 Mar 21
44
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
SYMBOL
PIN
EQUIVALENT CIRCUIT
DESCRIPTION
LINER
22
Line output right.
200 Ω
22
5.8 kΩ
5.8 kΩ
MLD027
DCOUTL
DCOUTR
HPOUTL
23
24
25
VU meter drive output left.
VU meter drive output right.
Headphone drive output left.
100 Ω
23
MLD028
100 Ω
24
MLD029
25
2.7 kΩ
8 kΩ
MLD030
1995 Mar 21
45
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
SYMBOL
PIN
EQUIVALENT CIRCUIT
DESCRIPTION
HPOUTR
26
Headphone drive output right.
26
2.7 kΩ
8 kΩ
MLD031
LINAGC
27
Linear audio AGC-time constant.
100 Ω
27
MLD032
LININ
28
29
Audio input for linear audio to REC
equalizer and output select.
28
90 kΩ
3.8 V
MLD033
LINOUT
Audio output from AGC or PB
equalizer.
playback
equalizer
AGC
29
250 µA
MLD034
EQSW
30
Long Play (LP) equalization switch;
15 Ω on resistance and 150 kΩ
input impedance.
30
43
V
SSA1
150 kΩ
MLD035
1995 Mar 21
46
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
SYMBOL
PIN
EQUIVALENT CIRCUIT
DESCRIPTION
RECEQ
31
Linear audio recording amplifier
negative feedback input for
connecting a record equalization
network.
33
1.75 kΩ
3.8 kΩ
MLD036
31
LINREC
32
Digital output controlled by I2C-bit
RN; can be used to drive an
external (high voltage) head switch
and possibly the bias oscillator.
32
275 Ω
MLD037
RECOUT
33
Linear audio recording amplifier
output.
100 Ω
33
1.6 kΩ
4.8 kΩ
MLD038
31
1995 Mar 21
47
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
SYMBOL
PIN
EQUIVALENT CIRCUIT
DESCRIPTION
PBIN
34
Linear audio playback amplifier
input; during playback the
impedance is 100 kΩ; during record
the impedance is 7 Ω.
35
150 kΩ
RESSW
PBDC
35
36
Long Play equalization switch 50 Ω
on and 150 kΩ off impedance to
PBIN.
Linear audio playback amplifier
DC decoupling.
100 kΩ
3.8 V
470 Ω
36
34
3.8 V
MLD039
DCFBL
DCREFL
EMPHL
37
38
39
DC feedback left.
DC reference left.
3.8 V
38
Total emphasis left (240 to 20 µs).
4.3 kΩ 46.8 kΩ
100 kΩ
39
37
250 µA
MLD040
1995 Mar 21
48
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
SYMBOL
PIN
EQUIVALENT CIRCUIT
DESCRIPTION
RECTL
40
Rectifier DC decoupling left.
40
MLD041
DETL
41
Attack/recovery timing left.
384 Ω
16.4
µA
41
MLD042
Vref
42
Noise filtering of 3.8 V reference
voltage (external capacitor required
for filtering).
20 kΩ
3.8 V
42
MLD043
VSSA1
DETR
43
44
Analog ground 1 for LF circuits.
Attack/recovery timing right.
384 Ω
16.4
µA
44
MLD044
RECTR
45
Rectifier DC decoupling right.
45
MLD045
1995 Mar 21
49
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
SYMBOL
PIN
EQUIVALENT CIRCUIT
DESCRIPTION
EMPHR
DCREFR
DCFBR
46
47
48
Total emphasis right (240 to 20 µs).
DC reference right.
3.8 V
DC feedback right.
4.3 kΩ 46.8 kΩ
100 kΩ
46
47
48
250 µA
MLD046
RFIX
49
Fixed bias current generation circuit
by using an external 180 kΩ
resistor to ground.
3.8 V
49
MLD047
VDDA1
AFNR
50
51
Analog supply voltage 1 for
LF circuits (+12 V).
Audio output from noise reduction
of right channel (record and
loop-through) or audio input for
noise reduction of right channel
(playback).
3.8 V
22.3 kΩ
to
from
noise
noise
reduction
reduction
2.7 kΩ
record
51
playback
250 µA
MLD048
1995 Mar 21
50
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
SYMBOL
PIN
EQUIVALENT CIRCUIT
DESCRIPTION
AFMR
52
Audio input for audio clipper of right
channel (record and loop-through)
or audio output from
25 kΩ
3.8 V
sample-and-hold (playback).
audio clipper
52
sample-
and- hold
playback
record
250 µA
MLD049
RCCOR
53
Voltage-to-current transfer for right
channel oscillator by means of an
external resistor to ground.
CCO-current
53
MLD050
VSSA2
RBPF
54
55
Analog ground 2 for HF circuits.
Bias current generation for the
internal band-pass filters by means
of an external resistor to ground.
1.3 V
55
MLD051
1995 Mar 21
51
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
SYMBOL
PIN
EQUIVALENT CIRCUIT
DESCRIPTION
FMOUT
56
FM output.
50 Ω
56
900 µA
MLD052
FMIN
57
FM input.
4 kΩ
15 kΩ
1.9 V
57
MLD053
VDDA2
58
59
Analog supply voltage 2 for
HF circuits (+5 V).
RCCOL
Voltage-to-current transfer for left
channel oscillator by means of an
external resistor to ground.
CCO-current
59
MLD054
ENVOUT
60
61
Level detector output (external
capacitor required for filtering).
60
33 kΩ
MLD055
HID
Head Identification Pulse (HID)
input for sample-and-hold circuits.
3 kΩ
2.5 V
61
MLD056
1995 Mar 21
52
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
SYMBOL
PIN
EQUIVALENT CIRCUIT
DESCRIPTION
CMUTE
62
Mute timing (external capacitor
required for playback mute).
26
62
1
275
Ω
18 µA
ENVOUT
PBMUTE
MLD057
AFML
63
Audio input for audio clipper of left
channel (record and loop-through)
or audio output from
25 kΩ
3.8 V
sample-and-hold circuit of left
channel (playback).
audio clipper
63
sample-
and- hold
playback
record
250 µA
MLD058
AFNL
64
Audio output from noise reduction
of left channel (record and
loop-through) or audio input for
noise reduction of left channel
(playback).
3.8 V
22.3 kΩ
to
from
noise
noise
reduction
reduction
2.7 kΩ
record
64
playback
250 µA
MLD059
1995 Mar 21
53
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
12 TEST AND APPLICATION INFORMATION
BM2E79
R E C O U T
P B I N
L I N E 2 L
R F O U T
R F C A G C
R E S S W
P B D C
S S D
V
D C F B L
D C R E F L
E M P H L
S C L
S D A
D D D
V
R E C T L
D E T L
R A F
E X T 3 R
E X T 3 L
r e f
V
S S A 1
V
E X T 2 R
E X T 2 L
E X T 1 R
E X T 1 L
C I N R
D E T R
R E C T R
E M P H R
D C R E F R
D C F B R
C I N L
R F I X
T U N R
T U N L
D D A 1
V
S A P
A F N R
1995 Mar 21
54
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
BM2E7
a n d b o o p
1995 Mar 21
55
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
12.2 RCCOL, RCCOR, RBPF and RFIX
12.1 RAF I/O (pin 12)
(pins 59, 53, 55 and 49)
The status of the I2C RAF bit is output (RAF = HIGH;
record). This output can be used to switch the audio
FM head amplifier to playback and record. If accurate fast
switching of the TDA9614H is needed, this pin can also be
used as input. Thereby overruling the I2C RAF bit. To
make this possible the RAF output is current limited.
The external resistors to ground at pins RCCOL, RCCOR,
RBPF and RFIX must have a tolerance of 5%. This is
necessary to guarantee correct functioning of the IC. The
temperature coefficient of the external resistors at
RCCOL, RCCOR and RBPF have a direct influence on the
related frequencies of the on-chip oscillators and
bandpass filters.
When using the RAF pin as output, no more than 35 µA
(LOW) and 185 µA (HIGH) current may be drawn from this
pin to assure that the mode of the TDA9614H is not
changed.
When using the RAF pin as input, the voltage source used
must be capable of delivering at least 345 µA
(forced HIGH; >3.5 V) or sinking at least 65 µA
(forced LOW; <1.5 V).
1995 Mar 21
56
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
13 PACKAGE OUTLINE
QFP64: plastic quad flat package; 64 leads (lead length 1.95 mm); body 14 x 20 x 2.8 mm
SOT319-2
y
X
A
51
33
52
32
Z
E
e
Q
A
2
H
A
E
(A )
3
E
A
1
θ
w M
p
pin 1 index
L
p
b
L
20
64
detail X
1
19
w M
Z
D
v
M
A
b
p
e
D
B
H
v
M
B
D
0
5
10 mm
scale
DIMENSIONS (mm are the original dimensions)
A
(1)
(1)
(1)
(1)
UNIT
A
A
A
b
c
D
E
e
H
D
H
L
L
Q
v
w
y
Z
Z
E
θ
1
2
3
p
E
p
D
max.
7o
0o
0.25 2.90
0.05 2.65
0.50 0.25 20.1 14.1
0.35 0.14 19.9 13.9
24.2 18.2
23.6 17.6
1.0
0.6
1.4
1.2
1.2
0.8
1.2
0.8
mm
3.20
0.25
1
1.95
0.2
0.2
0.1
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
EIAJ
92-11-17
95-02-04
SOT319-2
1995 Mar 21
57
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
Several techniques exist for reflowing; for example,
14 SOLDERING
thermal conduction by heated belt, infrared, and
vapour-phase reflow. Dwell times vary between 50 and
300 s according to method. Typical reflow temperatures
range from 215 to 250 °C.
14.1 Plastic quad flat packages
14.1.1 BY WAVE
During placement and before soldering, the component
must be fixed with a droplet of adhesive. After curing the
adhesive, the component can be soldered. The adhesive
can be applied by screen printing, pin transfer or syringe
dispensing.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 min at 45 °C.
14.1.3 REPAIRING SOLDERED JOINTS (BY HAND-HELD
SOLDERING IRON OR PULSE-HEATED SOLDER TOOL)
Maximum permissible solder temperature is 260 °C, and
maximum duration of package immersion in solder bath is
10 s, if allowed to cool to less than 150 °C within 6 s.
Typical dwell time is 4 s at 250 °C.
Fix the component by first soldering two, diagonally
opposite, end pins. Apply the heating tool to the flat part of
the pin only. Contact time must be limited to 10 s at up to
300 °C. When using proper tools, all other pins can be
soldered in one operation within 2 to 5 s at between 270
and 320 °C. (Pulse-heated soldering is not recommended
for SO packages.)
A modified wave soldering technique is recommended
using two solder waves (dual-wave), in which a turbulent
wave with high upward pressure is followed by a smooth
laminar wave. Using a mildly-activated flux eliminates the
need for removal of corrosive residues in most
applications.
For pulse-heated solder tool (resistance) soldering of VSO
packages, solder is applied to the substrate by dipping or
by an extra thick tin/lead plating before package
placement.
14.1.2 BY SOLDER PASTE REFLOW
Reflow soldering requires the solder paste (a suspension
of fine solder particles, flux and binding agent) to be
applied to the substrate by screen printing, stencilling or
pressure-syringe dispensing before device placement.
1995 Mar 21
58
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
and linear audio
TDA9614H
15 DEFINITIONS
Data sheet status
Objective specification
Preliminary specification
Product specification
This data sheet contains target or goal specifications for product development.
This data sheet contains preliminary data; supplementary data may be published later.
This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
16 LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
17 PURCHASE OF PHILIPS I2C COMPONENTS
Purchase of Philips I2C components conveys a license under the Philips’ I2C patent to use the
components in the I2C system provided the system conforms to the I2C specification defined by
Philips. This specification can be ordered using the code 9398 393 40011.
1995 Mar 21
59
Philips Semiconductors – a worldwide company
Argentina: IEROD, Av. Juramento 1992 - 14.b, (1428)
BUENOS AIRES, Tel. (541)786 7633, Fax. (541)786 9367
Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113,
Pakistan: Philips Electrical Industries of Pakistan Ltd.,
Exchange Bldg. ST-2/A, Block 9, KDA Scheme 5, Clifton,
KARACHI 75600, Tel. (021)587 4641-49,
Fax. (021)577035/5874546.
Tel. (02)805 4455, Fax. (02)805 4466
Philippines: PHILIPS SEMICONDUCTORS PHILIPPINES Inc,
106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI,
Metro MANILA, Tel. (02)810 0161, Fax. (02)817 3474
Austria: Triester Str. 64, A-1101 WIEN, P.O. Box 213,
Tel. (01)60 101-1236, Fax. (01)60 101-1211
Belgium: Postbus 90050, 5600 PB EINDHOVEN, The Netherlands,
Portugal: PHILIPS PORTUGUESA, S.A.,
Tel. (31)40 783 749, Fax. (31)40 788 399
Rua dr. António Loureiro Borges 5, Arquiparque - Miraflores,
Apartado 300, 2795 LINDA-A-VELHA,
Tel. (01)4163160/4163333, Fax. (01)4163174/4163366.
Brazil: Rua do Rocio 220 - 5th floor, Suite 51,
CEP: 04552-903-SÃO PAULO-SP, Brazil.
P.O. Box 7383 (01064-970).
Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231,
Tel. (65)350 2000, Fax. (65)251 6500
South Africa: S.A. PHILIPS Pty Ltd.,
Tel. (011)821-2333, Fax. (011)829-1849
Canada: PHILIPS SEMICONDUCTORS/COMPONENTS:
Tel. (800) 234-7381, Fax. (708) 296-8556
Chile: Av. Santa Maria 0760, SANTIAGO,
195-215 Main Road Martindale, 2092 JOHANNESBURG,
P.O. Box 7430 Johannesburg 2000,
Tel. (011)470-5911, Fax. (011)470-5494.
Tel. (02)773 816, Fax. (02)777 6730
Colombia: IPRELENSO LTDA, Carrera 21 No. 56-17,
77621 BOGOTA, Tel. (571)249 7624/(571)217 4609,
Fax. (571)217 4549
Denmark:Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S,
Tel. (032)88 2636, Fax. (031)57 1949
Finland: Sinikalliontie 3, FIN-02630 ESPOO,
Tel. (9)0-50261, Fax. (9)0-520971
France: 4 Rue du Port-aux-Vins, BP317,
92156 SURESNES Cedex,
Tel. (01)4099 6161, Fax. (01)4099 6427
Germany: P.O. Box 10 63 23, 20043 HAMBURG,
Tel. (040)3296-0, Fax. (040)3296 213.
Greece: No. 15, 25th March Street, GR 17778 TAVROS,
Tel. (01)4894 339/4894 911, Fax. (01)4814 240
Hong Kong: PHILIPS HONG KONG Ltd., 15/F Philips Ind. Bldg.,
24-28 Kung Yip St., KWAI CHUNG, N.T.,
Spain: Balmes 22, 08007 BARCELONA,
Tel. (03)301 6312, Fax. (03)301 42 43
Sweden: Kottbygatan 7, Akalla. S-164 85 STOCKHOLM,
Tel. (0)8-632 2000, Fax. (0)8-632 2745
Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH,
Tel. (01)488 2211, Fax. (01)481 77 30
Taiwan: PHILIPS TAIWAN Ltd., 23-30F, 66, Chung Hsiao West
Road, Sec. 1. Taipeh, Taiwan ROC, P.O. Box 22978,
TAIPEI 100, Tel. (02)388 7666, Fax. (02)382 4382.
Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd.,
209/2 Sanpavuth-Bangna Road Prakanong,
Bangkok 10260, THAILAND,
Tel. (662)398-0141, Fax. (662)398-3319.
Turkey:Talatpasa Cad. No. 5, 80640 GÜLTEPE/ISTANBUL,
Tel. (0212)279 27 70, Fax. (0212)282 67 07
United Kingdom: Philips Semiconductors LTD.,
276 Bath Road, Hayes, MIDDLESEX UB3 5BX,
Tel. (0181)730-5000, Fax. (0181)754-8421
United States:811 East Arques Avenue, SUNNYVALE,
CA 94088-3409, Tel. (800)234-7381, Fax. (708)296-8556
Uruguay: Coronel Mora 433, MONTEVIDEO,
Tel. (852)424 5121, Fax. (852)480 6960/480 6009
India: Philips INDIA Ltd, Shivsagar Estate, A Block ,
Dr. Annie Besant Rd. Worli, Bombay 400 018
Tel. (022)4938 541, Fax. (022)4938 722
Indonesia: Philips House, Jalan H.R. Rasuna Said Kav. 3-4,
P.O. Box 4252, JAKARTA 12950,
Tel. (02)70-4044, Fax. (02)92 0601
Tel. (021)5201 122, Fax. (021)5205 189
Ireland: Newstead, Clonskeagh, DUBLIN 14,
Internet: http://www.semiconductors.philips.com/ps/
Tel. (01)640 000, Fax. (01)640 200
Italy: PHILIPS SEMICONDUCTORS S.r.l.,
Piazza IV Novembre 3, 20124 MILANO,
Tel. (0039)2 6752 2531, Fax. (0039)2 6752 2557
For all other countries apply to: Philips Semiconductors,
International Marketing and Sales, Building BE-p,
P.O. Box 218, 5600 MD, EINDHOVEN, The Netherlands,
Telex 35000 phtcnl, Fax. +31-40-724825
Japan: Philips Bldg 13-37, Kohnan2-chome, Minato-ku, TOKYO 108,
Tel. (03)3740 5028, Fax. (03)3740 0580
Korea: (Republic of) Philips House, 260-199 Itaewon-dong,
SCD38
© Philips Electronics N.V. 1995
All rights are reserved. Reproduction in whole or in part is prohibited without the
prior written consent of the copyright owner.
Yongsan-ku, SEOUL, Tel. (02)794-5011, Fax. (02)798-8022
Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA,
SELANGOR, Tel. (03)750 5214, Fax. (03)757 4880
Mexico: 5900 Gateway East, Suite 200, EL PASO, TX 79905,
Tel. 9-5(800)234-7381, Fax. (708)296-8556
Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB
The information presented in this document does not form part of any quotation
or contract, is believed to be accurate and reliable and may be changed without
notice. No liability will be accepted by the publisher for any consequence of its
use. Publication thereof does not convey nor imply any license under patent- or
other industrial or intellectual property rights.
Tel. (040)783749, Fax. (040)788399
Printed in The Netherlands
New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND,
Tel. (09)849-4160, Fax. (09)849-7811
513061/1500/01/pp60
Date of release: 1995 Mar 21
9397 750 00047
Norway: Box 1, Manglerud 0612, OSLO,
Tel. (022)74 8000, Fax. (022)74 8341
Document order number:
Philips Semiconductors
相关型号：
©2020 ICPDF网 联系我们和版权申明