UPG155TB-E3 [NEC]
L-BAND SPDT SWITCH; L波段单刀双掷开关型号: | UPG155TB-E3 |
厂家: | NEC |
描述: | L-BAND SPDT SWITCH |
文件: | 总12页 (文件大小:69K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
DATA SHEET
GaAs INTEGRATED CIRCUIT
µPG155TB
L-BAND SPDT SWITCH
DESCRIPTION
The µPG155TB is an L-band SPDT (Single Pole Double Throw) GaAs FET switch which was developed for digital
cellular or cordless telephone application. The device can operate from 100 MHz to 2.5 GHz, having the low
insertion loss. It housed in an original 6-pin super minimold package that is smaller than usual 6-pin minimold easy
to install and contributes to miniaturizing the system.
FEATURES
•
•
•
Low Insertion Loss
: LINS = 0.75 dB TYP. @VCONT = +3.0 V/0 V, f = 2 GHz
High Linearity Switching: Pin (1 dB) = +34 dBm TYP. @VCONT = +3.0 V/0 V, f = 2 GHz
Small 6-pin super minimold package (Size: 2.0 × 1.25 × 0.9 mm)
APPLICATIONS
•
•
L, S-band digital cellular or cordless telephone
PCS, WLAN, and WLL applications
ORDERING INFORMATION
Part Number
Marking
G1L
Package
Supplying Form
Embossed tape 8 mm wide.
µPG155TB-E3
6-pin super minimold
Pin 1, 2, 3 face to tape perforation side.
Qty 3 kp/reel.
Remark To order evaluation samples, please contact your local NEC sales office. (Part number for sample
order: µPG155TB)
Caution The IC must be handled with care to prevent static discharge because its circuit is composed of
GaAs MES FET.
The information in this document is subject to change without notice. Before using this document, please
confirm that this is the latest version.
Not all devices/types available in every country. Please check with local NEC representative for
availability and additional information.
Document No. P13654EJ2V0DS00 (2nd edition)
Date Published November 1999 N CP(K)
Printed in Japan
The mark
shows major revised points.
©
1998, 1999
µPG155TB
ABSOLUTE MAXIMUM RATINGS (TA = +25°C)
Parameter
Control Voltage 1, 2
Input Power
Symbol
VCONT1, 2
Pin
Ratings
–6.0 to +6.0Note
+34
Unit
V
dBm
W
Total Power Dissipation
Operating Temperature
Storage Temperature
Ptot
0.15
TA
–45 to +85
–55 to +150
°C
Tstg
°C
Note Condition 2.5 ≤ | VCONT1 – VCONT2 | ≤ 6.0 V
Remarks 1. Mounted on a 50 × 50 × 1.6 mm double copper clad epoxy glass PWB, TA = +85°C
2. Operation in excess of any one of these parameters may result in permanent damage.
PIN CONNECTIONS
(Top View)
(Bottom View)
Pin No.
Connection
OUT1
Pin No.
Connection
VCONT2
IN
3
2
1
4
5
6
4
5
6
3
2
1
1
2
3
4
5
6
GND
OUT2
VCONT1
RECOMMENDED OPERATING CONDITIONS (TA = +25°C)
Parameter
Control Voltage (Low)
Control Voltage (High)
Symbol
VCONT
MIN.
–0.2
+2.5
TYP.
0
MAX.
+0.2
+5.3
Unit
V
VCONT
+3.0
V
2
Data Sheet P13654EJ2V0DS00
µPG155TB
ELECTRICAL CHARACTERISTICS
(Unless otherwise specified, TA = +25°C, VCONT1 = 3 V, VCONT2 = 0 V or VCONT1 = 0 V, VCONT2 = 3 V, ZO = 50 Ω
Off chip DC blocking capacitors value; 51 pF)
Parameter
Insertion Loss
Symbol
LINS
Test Conditions
f = 100 M to 1.0 GHz
f = 2.0 GHz
MIN.
−
TYP.
0.60
0.75
0.90Note 1
16
MAX.
Unit
dB
0.8
1.0
−
−
f = 2.5 GHz
−
Isolation
ISL
f = 100 M to 2.0 GHz
f = 2.5 GHz
13
−
−
dB
10Note 1
21.5
15
−
f = 1.0 GHz
18
11
11
−
−
Input Return Loss
Output Return Loss
RLin
RLout
f = 100 M to 2.0 GHz
f = 100 M to 2.0 GHz
f = 2.0 GHz
−
dB
dB
15
−
Input Power at 0.1 dB
Compression PointNote 2
Pin (0.1 dB)
30.5
−
dBm
Input Power at 1 dB
Compression PointNote 2
Pin (1 dB)
f = 2.0 GHz
32
34
−
dBm
Switching Speed
Control Current
tsw
−
−
30
20
−
ns
ICONT
VCONT = 3 V/0 V
50
µA
Notes 1. Characteristic for reference at f = 2.0 to 2.5 GHz
2. Pin (0.1 dB) or Pin (1 dB) is measured the input power level when the insertion loss increases more 0.1 dB or
1 dB than that of linear range. All other characteristics are measured in linear range.
Cautions 1. When the µPG155TB is used, it is necessary to use DC blocking capacitors for No.1 (OUT1),
No.3 (OUT2) and No.5 (IN). The value of DC blocking capacitors should be chosen to
accommodate the frequency of operation, band width, switching speed and the condition
with actual board of your system.
The range of recommended DC blocking capacitor value is less than 100 pF.
2. The distance between IC’s GND pin and ground pattern of substrate should be as shorter as
possible to avoid parasitic parameters.
3
Data Sheet P13654EJ2V0DS00
µPG155TB
TYPICAL CHARACTERISTICS (ON)
TEST CONDITIONS: VCONT = 3 V/0 V, Pin = 0 dBm, TA = +25°C
OUT1
IN
OUT2
50 Ω
IN-OUT1 INPUT RETURN LOSS vs. FREQUENCY
IN-OUT1 ISOLATION vs. FREQUENCY
CH1 S11 log MAG
10 dB/REF 0 dB
CH1 S12 log MAG
10 dB/REF 0 dB
1: –23.361 dB
1 GHz
1: –22.041 dB
1 GHz
2: –25.86 dB
1.5 GHz
2: –18.211 dB
1.5 GHz
3: –23.513 dB
2 GHz
4: –15.758 dB
2.5 GHz
3: –15.377 dB
2 GHz
4: –14.159 dB
2.5 GHz
MARKER 1
1 GHz
MARKER 1
1 GHz
0
0
–10
–10
1
1
4
–20
–20
4
3
2
3
–30
–40
–30
–40
2
START 0.300 000 000 GHz STOP 3.300 000 000 GHz
Frequency f (GHz)
START 0.300 000 000 GHz STOP 3.300 000 000 GHz
Frequency f (GHz)
IN-OUT1 INSERTION LOSS vs. FREQUENCY
IN-OUT1 OUTPUT RETURN LOSS vs. FREQUENCY
CH1 S21 log MAG
1 dB/REF 0 dB
CH1 S22 log MAG
10 dB/REF 0 dB
1: –0.959 dB
1 GHz
1: –24.263 dB
1 GHz
2: –1.078 dB
1.5 GHz
2: –34.835 dB
1.5 GHz
3: –1.255 dB
2 GHz
4: –1.618 dB
2.5 GHz
3: –25.152 dB
2 GHz
4: –15.675 dB
2.5 GHz
MARKER 1
1 GHz
MARKER 1
1 GHz
0
0
1
–1
–2
–3
–4
–10
2
1
3
–20
4
4
–30
–40
3
2
START 0.300 000 000 GHz STOP 3.300 000 000 GHz
Frequency f (GHz)
START 0.300 000 000 GHz STOP 3.300 000 000 GHz
Frequency f (GHz)
Caution This data is including loss of the test fixture.
4
Data Sheet P13654EJ2V0DS00
µPG155TB
TYPICAL CHARACTERISTICS (OFF)
TEST CONDITIONS: VCONT1 = VCONT2 = 3 V/3 V, Pin = 0 dBm, TA = +25°C
OUT1
IN
OUT2
50 Ω
IN-OUT1 INPUT RETURN LOSS vs. FREQUENCY
CH1 S11 log MAG
10 dB/REF 0 dB
1: –11.777 dB
1 GHz
2: –11.405 dB
1.5 GHz
3: –11.344 dB
2 GHz
4: –10.281 dB
2.5 GHz
MARKER 1
1 GHz
0
1
–10
4
3
2
–20
–30
–40
START 0.300 000 000 GHz STOP 3.300 000 000 GHz
Frequency f (GHz)
IN-OUT1 INSERTION LOSS vs. FREQUENCY
IN-OUT1 OUTPUT RETURN LOSS vs. FREQUENCY
CH1 S21 log MAG
10 dB/REF 0 dB
CH1 S22 log MAG
10 dB/REF 0 dB
1: –4.392 dB
1 GHz
1: –14.144 dB
1 GHz
2: –4.417 dB
1.5 GHz
2: –13.091 dB
1.5 GHz
3: –4.447 dB
2 GHz
4: –4.594 dB
2.5 GHz
3: –12.966 dB
2 GHz
4: –14.503 dB
2.5 GHz
MARKER 1
1 GHz
MARKER 1
1 GHz
1
0
0
1
2
3
4
–10
–20
–30
–40
–10
2
3
4
–20
–30
–40
START 0.300 000 000 GHz STOP 3.300 000 000 GHz
Frequency f (GHz)
START 0.300 000 000 GHz STOP 3.300 000 000 GHz
Frequency f (GHz)
Caution This data is including loss of the test fixture.
5
Data Sheet P13654EJ2V0DS00
PPG155TB
TEST CIRCUIT
TA = +25qC, VCONT1 = +3 V, VCONT2 = 0 V or VCONT1 = 0 V, VCONT2 = +3 V, f = 2 GHz, ZO = 50 :
Off chip DC blocking capacitors value: C0 = 51 pF, C1 = 1 000 pF (Bypass), using NEC standard evaluation board
OUT1
OUT2
C0
C0
1
2
3
G1L
6
5
4
C1
C1
C0
VCONT1
IN
V
CONT2
EVALUATION BOARD
OUT1
OUT2
VCONT1
V
CONT2
IN
6
Data Sheet P13654EJ2V0DS00
µPG155TB
TRUTH TABLE OF SWITCHING BY CONDITION OF CONTROL VOLTAGE
VCONT1
VCONT(H)
VCONT(L)
VCONT2
VCONT(H)
Note
OUT1
OUT2
OUT1
OUT2
IN
IN
VCONT(L)
Note
OUT1
OUT2
IN
OUT1
OUT2
IN
Note In case of VCONT1 = VCONT2 = High or VCONT1 = VCONT2 = Low, (that is same control voltage for both pins),
input signal of IN (Pin 5) is output from OUT1 (Pin 1) and OUT2 (Pin 3).
PACKAGE DIMENSIONS
6 PIN MINIMOLD (Unit: mm)
+0.1
+0.1
0.2
0.15
–0
–0
0 to 0.1
0.7
0.65
0.65
1.3
2.0 ±0.2
0.9 ±0.1
7
Data Sheet P13654EJ2V0DS00
µPG155TB
RECOMMENDED SOLDERING CONDITIONS
This product should be soldered under the following recommended conditions. For soldering method and
conditions other than those recommended below, contact your NEC sales representative.
Soldering Method
Infrared Reflow
Soldering Conditions
Recommended Condition Symbol
IR35-00-3
Package peak temperature: 235°C or below
Time: 30 seconds or less (at 210°C)
Count: 3, Exposure limit: NoneNote
VPS
Package peak temperature: 215°C or below
Time: 40 seconds or less (at 200°C)
Count: 3, Exposure limit: NoneNote
VP15-00-3
WS60-00-1
–
Wave Soldering
Partial Heating
Soldering bath temperature: 260°C or below
Time: 10 seconds or less
Count: 1, Exposure limit: NoneNote
Pin temperature: 300°C
Time: 3 seconds or less (per pin row)
Exposure limit: NoneNote
Note After opening the dry pack, keep it in a place below 25°C and 65% RH for the allowable storage period.
Caution Do not use different soldering methods together (except for partial heating).
8
Data Sheet P13654EJ2V0DS00
µPG155TB
[MEMO]
9
Data Sheet P13654EJ2V0DS00
µPG155TB
[MEMO]
10
Data Sheet P13654EJ2V0DS00
µPG155TB
[MEMO]
11
Data Sheet P13654EJ2V0DS00
µPG155TB
Caution
The Great Care must be taken in dealing with the devices in this guide.
The reason is that the material of the devices is GaAs (Gallium Arsenide), which is
designated as harmful substance according to the law concerned.
Keep the law concerned and so on, especially in case of removal.
• The information in this document is subject to change without notice. Before using this document, please
confirm that this is the latest version.
• No part of this document may be copied or reproduced in any form or by any means without the prior written
consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in
this document.
• NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property
rights of third parties by or arising from use of a device described herein or any other liability arising from use
of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other
intellectual property rights of NEC Corporation or others.
• Descriptions of circuits, software, and other related information in this document are provided for illustrative
purposes in semiconductor product operation and application examples. The incorporation of these circuits,
software, and information in the design of the customer's equipment shall be done under the full responsibility
of the customer. NEC Corporation assumes no responsibility for any losses incurred by the customer or third
parties arising from the use of these circuits, software, and information.
• While NEC Corporation has been making continuous effort to enhance the reliability of its semiconductor devices,
the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or
property arising from a defect in an NEC semiconductor device, customers must incorporate sufficient safety
measures in its design, such as redundancy, fire-containment, and anti-failure features.
• NEC devices are classified into the following three quality grades:
"Standard", "Special", and "Specific". The Specific quality grade applies only to devices developed based on a
customer designated "quality assurance program" for a specific application. The recommended applications of
a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device
before using it in a particular application.
Standard: Computers, office equipment, communications equipment, test and measurement equipment,
audio and visual equipment, home electronic appliances, machine tools, personal electronic
equipment and industrial robots
Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster
systems, anti-crime systems, safety equipment and medical equipment (not specifically designed
for life support)
Specific: Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life
support systems or medical equipment for life support, etc.
The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books.
If customers intend to use NEC devices for applications other than those specified for Standard quality grade,
they should contact an NEC sales representative in advance.
M7 98. 8
相关型号:
UPG168TB
SPDT, 500MHz Min, 2500MHz Max, 0.9dB Insertion Loss-Max, 2 X 1.25 MM, 0.90 MM HEIGHT, SUPER MINIMOLD PACKAGE-6
NEC
UPG168TB-A
SPDT, 500MHz Min, 2500MHz Max, 0.9dB Insertion Loss-Max, 2 X 1.25 MM, 0.90 MM HEIGHT, SUPER MINIMOLD PACKAGE-6
NEC
©2020 ICPDF网 联系我们和版权申明