DMS-EB-C [MURATA]

Multi-Purpose Application Board for DMS-30 & DMS-40 Series Meters; 多功能应用板的DMS- 30 DMS- 40系列仪表


型号：	DMS-EB-C
厂家：	muRata
描述：	Multi-Purpose Application Board for DMS-30 & DMS-40 Series Meters 多功能应用板的DMS- 30 DMS- 40系列仪表仪表
文件：	总4页 (文件大小：287K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

DMS-EB

Multi-Purpose Application Board for DMS-30 & DMS-40 Series Meters

FEATURES

ꢀ

Accommodates 3½ and 4½ digit meters

ꢀ

Gain (span) and offset (zero) adjustments for

DMS-30 meters

PRODUCT OVERVIEW

The DMS-EB Application Board covers many common panel meter applications while providing

simple signal and power I/O terminations (via a standard MOLEX connector) for DATEL's DMS-30 and

DMS-40 Series, LED/LCD Display, Digital Panel Voltmeters. The unique plug-and-play design of the

DMS-EB makes changing from application to application and meter to meter quick, easy and inexpensive.

The highly versatile DMS-EB has provisions for such common applications as attenuation of high

input voltages, gain (span) and offset (zero) adjustments, 9/12V battery operation, and direct decimal

point placement. The DMS-EB is compatible with all four versions of the DMS-30 and DMS-40 Series

( 200mV, 2V, 20V and 200V) making it interchangeable from meter to meter and application to

application. Solder gaps conveniently placed on the board are easily bridged or cut conﬁguring the board

to meet each application's speciﬁc requirements.

ꢀ

Input divider network for high voltages

Operate meter and board from +5V supply or

9/12V battery

ꢀ

Solder gaps for decimal placement

Same size as DMS-30/40 Series meters

2.02" (51.31mm)L x 0.83" (21.08mm)W

This low-cost addition to DATEL's expanding line of miniature meters is evidence of our continuing

commitment to offer the most versatile, easy-to-use, panel meter products.

SIMPLIFIED SCHEMATIC

NOTE:

Components are user-supplied and not part

of the standard product.

Figure 1. DMS-EB Schematic Diagram for DMS-30 Meters

For full details go to

www.murata-ps.com/rohs

www.murata-ps.com

Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000

MPM_DMS-EB.B01 Page 1 of 4

DMS-EB

Multi-Purpose Application Board for DMS-30 & DMS-40 Series Meters

Close SG6 when measuring ﬂoating inputs with a 9V-powered meter

(ﬂoating inputs are described in Technical Note 7). SG6 provides a bias

reference for the input signal by tying LO to the meter's Analog Com-

mon terminal (pin 10).

Ordering Information

DMS-EB-C Application board with mating connector

and terminals

DMS-BZL1-C DMS-30/40 bezel assembly

DMS-BZL2-C DMS-30/40 bezel assembly with

sealing gasket

3. Input Resistor Dividers: Use 1%, or better, metal ﬁlm resistors for

R1 and R2 in DMS-30 applications, and 0.5%, or better, in DMS-40

applications. Using tight-tolerance resistors in input divider networks

allows most ﬁnal calibration adjustments to be made with the meter's

rear calibration pots through the access holes provided. Make sure

the resistor power and voltage ratings are adequate for the given

application.

Functional Speciﬁcations

(TA = +25°C)

Input Supply Range

See applicable meter's data sheet

4. Using U1 (LM7805CT): The power supply voltage range listed in the

Battery Operation section is rated for a 150mA LED meter or a 35mA

backlit LCD meter. A 10μF/35V tantalum capacitor (C2) should be

installed with the polarized end next to the + symbol on the DMS-EB.

This is especially important if the power supply is located far from U1.

Input Supply Range

DMS-30/40PC-X-XS

DMS-30/40PC-X-XL

DMS-30/40LCD-X-5

DMS-30/40LCD-X-5B

U1 (LM7805CT) Installed:

+7.5 to +12.6V

+7.5 to +18.0V

+7.5 to +32.0V

+7.5 to +12.6V

Operating and Storage Temperature

Humidity

See applicable meter's data sheet

0 to 95%, non-condensing

5. DMS-40 Meters: When the DMS-EB is used with DMS-40PC or DMS-

40LCD meters, be sure to open SG13. The RN-DMS resistor acces-

sory kit comprised of resistor R3 and potentiometers R4 (Gain/Span)

and R5 (Offset/Zero), cannot be used with DMS-40 series meters. To

change the input range on DMS-40LCD meters from the low range to

the high range, close SG16.

Dimensions

2.02" (51.31mm)L x 0.83" (21.08mm)W

J1 Connector & Wire Information

Terminal Type

Crimp Tool

Wire Size

Insulation Diameter

Stripping Length

DATEL P/N 4400-01032-0

DATEL P/N 39-2099000

22 to 26 AWG

0.062" (1.57mm) max.

0.100" to 0.125" (2.54 to 3.17mm)

6. Calibration Potentiometer Adjustment Holes: Two overlapping

holes on the DMS-EB provide access to the ¾-turn calibration poten-

tiometer on DMS-30 meters and the 3-turn potentiometer on DMS-40

meters. The adjustment range of both pots is very narrow. See the

applicable product data sheet for more information on each meter’s

calibration potentiometers.

Introduction

As shipped, the DMS-EB is conﬁgured for 5V-powered DMS-30 3½

digit meters operating in the single-ended mode (SG5 closed) using the

meter's internal reference (SG13 closed). This conﬁguration is the most

common and works well for most simple voltage measurements.

Many of the applications described below apply to both DMS-30

and DMS-40 meters. However, Application 5, installing the span (R4) and

offset (R5) adjust potentiometers, can only be used with DMS-30 meters.

Also note that some of the other applications require the installation of

R4 and R5. See Technical Note 5 when using the DMS-EB with DMS-40

meters.

7. Input Conﬁgurations: The DMS-EB is supplied with SG5 closed. SG5

connects J1, pin 2 (LO) to power return J1, pin 6 (GND) and conﬁgures

the meter for single-ended operation, that is, the low side of the input

is at system ground or zero Volts. SG5 must also be closed when

measuring ﬂoating inputs. Floating inputs are signals which have no

electrical connection, or reference to, the power supply which powers

the meter.

In applications in which input LO is connected to ground elsewhere in

the system, and SG5 is closed, unwanted ground-loop induced display

errors may develop. Ground loops, a condition in which display drive

currents also ﬂow through the input signal wiring, can cause unstable

display readings. If this occurs, try opening SG5 to see if the display

stabilizes.

Please read all of the following technical notes and perform any

required modiﬁcations before soldering the DMS-EB onto the meter

(aligning pin 1 to pin 1). After soldering, carefully connect +5Vdc to +V

(J1, pin 5) and power return to –V (J1, pin 6).

TECHNICAL NOTES

SG5 must be open when measuring differential inputs that are refer-

enced to the same supply which powers the meter. DMS Application

Note 2 (Input Conﬁgurations, Power Supplies and Ground Loops)

provides a detailed discussion of input conﬁgurations.

1. LCD Backlighting: For DMS-30LCD backlit models, close SG15. For

DMS-40LCD backlit models close SG18. See the DMS-30LCD or the

DMS-40LCD data sheets for limitations on backlighting 9V-powered

meters.

8. Soldering: DATEL recommends the use of "no-clean" solders when

installing or making modiﬁcations to the DMS-EB.

2. 9V-Powered, LCD Display Models: DMS-30LCD-X-9 and DMS-

40LCD-X/X-9 meters cannot be used in single-ended input conﬁgura-

tions, i.e., LO (J1, pin 2) cannot be connected to GND (J1, pin 6). When

operating from a 7.5 to 14Vdc power source with a single-ended

input, use a +5V-powered meter and install U1 (see Battery Operation

section and Technical Note 4).

www.murata-ps.com

Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000

MPM_DMS-EB.B01 Page 2 of 4

DMS-EB

Multi-Purpose Application Board for DMS-30 & DMS-40 Series Meters

APPLICATIONS

1. Decimal Point Placement: DATEL ships the DMS-EB with all decimal

Using Full Range Span Adjustment (DMS-30 Only)

point solder gaps (SG1, SG2, SG3 and SG17) open. To enable a speciﬁc

decimal point, close its respective solder gap with solder. When reas-

signing decimal places for subsequent applications, remember to

open previously closed solder gaps.

5.1. For DMS-30-1 and -2 models: Conﬁguring the DMS-EB for span

adjustment is simply a matter of installing resistor R3 and potenti-

ometer R4, opening SG13 and then closing SG8, SG11 and SG12.

5.2. For DMS-30-0 models: Span adjustment requires that you open

SG8, SG11 (if closed) and SG13 and then close SG7, SG9 and

SG12. Then install R3 and R4.

Close SG1 for 1.999 (DP1)

Close SG2 for 19.99 (DP2)

Close SG3 for 199.9 (DP3)

Adjust span as desired. DMS-30-1 and -2 span adjustment range

is typically +10% and –5%. The DMS-30-0 has a much wider span

adjust, however, it should be limited to 10% for optimum accuracy.

Close SG17 for 1999.9 (DP4 on DMS-40)

2. Display Test: Tie J1, pin 4 (TEST OUT) to pin 3 (TEST IN) to test the

display of the DMS-30. Do not leave the meter in the test mode for

more than 10 seconds. Display test is not available on backlit models.

6. Measuring Input Voltages Greater than 1.999Vdc (Use DMS-30-1

Only): If possible, the resistors used for R1 and R2 should be 1%

metal-ﬁlm types with TCR's less than 100ppm/°C. More information

on selecting 1% resistors can be found in Application Note 14.

3. Battery Operation: Open SG4 and install U1 (LM7805CT) with its

metal tab facing down as shown Figure 2. Allowable input power

ranges (J1, pins 5 and 6) are as follows:

CAUTION: Do not exceed 250Vdc input signals.

DMS-30/40PC-X-XS

DMS-30/40PC-X-XL

DMS-30/40LCD-X-5

DMS-30/40LCD-X-5B

+7.5 to +12.6V

+7.5 to +18.0V

+7.5 to +32.0V

+7.5 to +12.6V

6.1. Open SG10. For applications in which input voltages exceed

100Vdc, also cut the 2 adjoining traces.

6.2. Conﬁgure the DMS-EB for span adjust using the procedure revi-

ously outlined for the DMS-30-1 version.

6.3. Calculate values for R1 and R2 as follows:

Metal tab

points down

SG1ꢀ

SG3

SG2

SG1

xx.xx

xxx.x

x.xxx

To measure input voltages

greater than 1ꢀꢀ0dcꢁ

open SG1ꢀ and also cut

these two etch paths.

Figure 2. Installing U1

4. Differential Input Signals (Signal Referenced to Power Source):

Open SG5. Apply the input signal to pin 1, (+) IN HI, and pin 2, (–) IN

LO, of J1.

Figure 3. Installing R1

A typical value for R1 is 1MΩ. The sum of R1 + R2 should be

between 50kΩ and 10MΩ.

Note: Common mode voltage must not exceed 2Vdc. Differential

signals are deﬁned as inputs whose two terminals are both above and

below J1, pin 6 (GROUND).

R2 = (FSI x R1) / ( |V^IN| - FSI)

Where:

5. Span (Gain) and Zero (Offset) Adjustments: Locations are included

on the DMS-EB to add user-supplied potentiometers R4 and R5, and

resistor R3. Recommended values for these components are as fol-

lows: R3: 10.5KΩ, 1%, 1/8W metal ﬁlm; R4: 2KΩ, 10-20-turns; R5:

50KΩ, 10-20 turns. Vishay's T93YA series potentiometers are suitable

for this application. Make sure to use only RoHS-compliant compo-

nents and solders when making modiﬁcations to DMS-EB.

FSI = The attenuated voltage, between the meter's (–) IN LO and

(+) IN HI pins, needed to achieve the desired display readings

V^IN= Input voltage at J1 (between pins 1 and 2)

Once installed, these components permit the span and zero adjust-

ments described in the following sections. R3 and R4 provide span

adjust, while R5 applies and offset voltage to (-) IN LO (J1, pin 2).

www.murata-ps.com

Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000

MPM_DMS-EB.B01 Page 3 of 4

DMS-EB

Multi-Purpose Application Board for DMS-30 & DMS-40 Series Meters

APPLICATIONS

7.1. Install R2: R2 = FSR / (IMAX. x 10000) where FSR is the desired

Example

meter reading (0 -1999) and I^MAXis between 0 -1 Ampere.

VIN is 0-5Vdc, and the display reading must be "000" to "1500."

7.2. Open SG5.

1. Assume R1 = 1.0MΩ.

7.3. Conﬁgure the DMS-EB for span adjust using the procedure previ-

ously outlined for the DMS-30-0 version.

2. R2 = (FSI x R1) / ( |V^IN| - FSI)

R2 = (1.500 x 1,000,000) / (5.0 - 1.500)

R2 = 428,571Ω or 432kΩ

7.4. Apply input signal (current) to (+) IN HI and (–) IN LO.

7.5. Adjust R4 for desired full scale readings.

3. Calibrate the meter using a known voltage source. Adjust R4 to

compensate for variations in R1 and R2.

7.6. Enable the appropriate decimal point using either SG1, SG2, SG3

or SG-17.

7. Current Measurements (Use 200mV Model, DMS-30-0): The follow-

ing instructions are for measuring current derived from the DMS-

30/40's power source. When measuring current that is ﬂoating with

respect to J1, pin 6 (POWER RETURN), leave SG5 closed.

Example

A 0.100 Ampere input must read "100.0" on the display.

R2 = 1000 / (0.1 x 10000)

R2 = 1 Ohm

CAUTION: Do not exceed 1 Ampere input current

Enable DP3 via SG3 for a reading of "100.0."

HI LO TST TST +V –V

(+) (–) IN OUT

GND

Figure 4. DMS-EB Board

USA:

Mansﬁeld (MA), Tel: (508) 339-3000, email: sales@murata-ps.com

Toronto, Tel: (866) 740-1232, email: toronto@murata-ps.com

Canada:

UK:

Milton Keynes, Tel: +44 (0)1908 615232, email: mk@murata-ps.com

Montigny Le Bretonneux, Tel: +33 (0)1 34 60 01 01, email: france@murata-ps.com

München, Tel: +49 (0)89-544334-0, email: munich@murata-ps.com

Murata Power Solutions, Inc.

France:

Germany:

Japan:

11 Cabot Boulevard, Mansﬁeld, MA 02048-1151 U.S.A.

Tel: (508) 339-3000 (800) 233-2765 Fax: (508) 339-6356

www.murata-ps.com email: sales@murata-ps.com ISO 9001 and 14001 REGISTERED

Tokyo, Tel: 3-3779-1031, email: sales_tokyo@murata-ps.com

Osaka, Tel: 6-6354-2025, email: sales_osaka@murata-ps.com

12/15/08

Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other

technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply

the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Speciﬁcations are subject to change without

China:

Shanghai, Tel: +86 215 027 3678, email: shanghai@murata-ps.com

Guangzhou, Tel: +86 208 221 8066, email: guangzhou@murata-ps.com

notice.

Singapore: Parkway Centre, Tel: +65 6348 9096, email: singapore@murata-ps.com

www.murata-ps.com

Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000

MPM_DMS-EB.B01 Page 4 of 4

DMS-EB-C [MURATA]

相关型号：

DMS-EB-RMS

DMS-EB2

DMS-LM2

DMS-LM3

DMS-PS-CM

DMS-PS1-CM

DMS-PS1-CM-C

DMS-PS10-CM

DMS-PS11-CM

DMS-PS12-CM

DMS-PS2-CM

DMS-PS3-CM