DMS-PS3-CM [MURATA]

High Efficiency, AC/DC Instrumentation Power Supplies with Individually Isolated Outputs; 高效率， AC / DC仪表电源，带有单独隔离输出


型号：	DMS-PS3-CM
厂家：	muRata
描述：	High Efficiency, AC/DC Instrumentation Power Supplies with Individually Isolated Outputs 高效率， AC / DC仪表电源，带有单独隔离输出仪表
文件：	总8页 (文件大小：529K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

DMS-PS-CM Series

High Efﬁciency, AC/DC Instrumentation Power

Supplies with Individually Isolated Outputs

Universal Input

85-264Vac or 110-340Vdc

FEATURES

Up to 80% efﬁcient single, dual, and triple-

output model

Individual, fully-isolated outputs:

3000Vac on main

US E156931

4000V double-isolation on auxiliaries

Murata Power Solution’s DMS-PS-CM Series

night light! These low cost, high-efﬁciency

power supplies can signiﬁcantly reduce

long-term electricity costs in low (<5Watts)

to medium (<16Watts) power applications.

All DMS-PSX-CM power supplies fea-

ture universal inputs of 85-264Vac 50/60Hz,

built-in line fuses, and on-board ‘Power On’

LED indicators. At full rated load, hold-up

time is typically 20ms at 120Vac, and 80ms

at 230Vac. All outputs provide indeﬁnite

short-circuit protection and, for added reli-

ability, the main high-current output also

includes overvoltage protection. A rugged,

vibration-proof, chassis mount package

incorporates large, shock-resistant terminal

blocks for all I/O connections.

of high-efﬁciency, chassis mount AC/DC

power supplies feature low noise (40mV on

main, 8mV on auxiliaries), fully-isolated +24,

+12V, and +5V outputs, making them perfect

for powering today’s complex instrumenta-

tion. A high-current main output is isolated

from the AC line by 3000Vac. In dual- and

triple-output models, the low-current auxiliary

outputs are isolated from the main output by

1000Vdc, and from each other by 2000Vdc,

effectively providing double isolation from the

AC line! This unprecedented isolation elimi-

nates ground loop problems in complex,

multiple-instrument applications.

Full-load efﬁciencies of up to 80% and

output-power ratings of 5, 10 or 16 Watts,

combine to ensure minimal ac power con-

sumption. For intermittent use or low-power

applications, the 5-Watt model’s no-load

quiescent consumption with a nominal

120Vac input is a mere 0.6 Watts---that’s

nearly seven times less than a standard 4W

Available with +5V, +12V, and +24V outputs

Low noise: 40mVp-pk on main, 8mVp-pk on

auxiliaries; Ideal for sensitive instrumentation

Universal input: 85-264Vac @ 47-63Hz or

110-340Vdc

Choice of 5, 10, or 16W models for minimal

system power-consumption

Standby power consumption as low as 0.6W

Short-circuit protection on all outputs;

OVP on main output

Built-in ac mains fuse & ‘Power On’ indicator

5W models operate up to 5 LED-display DPM’s

Multiple outputs, low noise, low cost,

Vibration-resistant, chassis-mount

modular packages

high efﬁciency, double isolation, and rugged

construction combine to make DMS-PSX-

CM Series AC/DC power supplies the

ideal choice for powering today’s sensitive

instrumentation, and any electronic device

that requires a reliable dc voltage!

EMC compliant; UL/CSA recognized

Low cost!

LDO

Regulator

DC/DC

Converter

TB3

TB2

–

OUT

GND

V3 (Auxilliary)

–

LDO

Regulator

^DC/DC**

Converter

1A/250V

–

AC/DC Converter

OUT

GND

TB4

(Auxilliary)

AC(L)

AC(N)

–

85-264V

50/60Hz

TB1

Drive

Circuitry

110-340Vdc

(Main)

110-340Vdc

–

*Not used on single-output models

**Used only on dual and triple-output models

For full details go to

www.murata-ps.com/rohs

Figure 1. Simpliﬁed Schematic

Figure 1. DMS-PS-CM Series Simpliﬁed Schematic

www.murata-ps.com

Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000

MPM_DMS-PS-CM.B02 Page 1 of 8

DMS-PS-CM Series

High Efﬁciency, AC/DC Instrumentation Power

Supplies with Individually Isolated Outputs

Performance/Functional Speciﬁcations

Typical at TA = +25°C and VIN = 85-264V @47-63Hz

AC Input

Input Voltage Range, All models ~

DC Outputs (continued)

Efﬁciency (Typ.@ 120Vac, full load):

85-264V @47-63Hz

Single Output Models

Dual Output Models

Triple Output Models

75ꢀ

73ꢀ

71ꢀ

Input Current (115V/230V, typ.):

5-Watt Models

10-Watt Models

0.15A/0.07A

0.3A/0.13A

0.33A/0.16A

16-Watt Models

DC-Output Terminal Blocks (TB1, TB2, TB3):

Wire Size &Type

16-20AWG (1.5 to 0.5mm²),

solid or stranded

Inrush Current (All models, typical peak):

@115Vac

@230Vac

14.1A

32.5A

Insulation Strip Length

Screw Tightening Torque

0.25 inches (6.4mm)

3.6 pound-inches (0.4Nm)

Isolation (Min.):

Short Circuit Protection (All outputs)

Overvoltage Protection V1 (max.)

Foldback, self-recovering

134ꢀ x Vout

Output V1 to AC Input

3000Vac

Outputs V2 & V3 to AC Input

AC Input to Frame Ground

Output V1 to Frame Ground

Outputs V2 & V3 to Frame Ground

Outputs V2 & V3 to Output V1

Output V2 to Output V3

3000Vac + 1000Vdc

1500Vac

Environmental

Operating Temperature

–25 to +70°C @ 50ꢀ rated power

500Vac

0 to +50°C @ full rated power;

(see Figure 3)

500Vac + 1000Vdc

1000Vdc

2000Vdc

Storage Temperature

Cooling

–40 to +85°C

Frame Ground Leakage Current (Max.):

@115Vac

@230Vac

Free air convection with derating

(see Figure 3 and Technical

0.5mA

3.5mA

Notes)

Switching Frequency (Typical):

V1 (5W and 10W models)

V1 (16W models)

Humidity (Non-condensing)

0 to 85ꢀ

75kHz

83kHz

100kHz

Physical

Dimensions

V2 & V3 (All models)

See Mechanical Speciﬁcations

Line Fuse (Built-in)

IEC60127-2, sheet 3 speciﬁcation

(slow-blow)

1A/250Vac, 5 x 20mm, meeting

for time lag fuses

Weight:

5 Watt Models

10 Watt Models

16 Watt Models

5.8 ounces (165 grams)

6.9 ounces (195 grams)

7.9 ounces (223 grams)

AC Mains Terminal Block (TB4):

Wire Size & Type

14-20AWG (2.5 to 0.5mm²),

solid or stranded

Case Materials:

Outer Case

ABS, UL94 5VA

Phenolic, UL94 V-0

Plastic, UL94 V-1

Insulation Strip Length

Screw Tightening Torque

Rated Voltage

0.25 inches (6.4mm)

DC/DC Modules

AC/DC Modules

4.4 pound-inches (0.5Nm)

630V (VDE 0110-V. Group 2);

250V (VDE 0110-V. Group 3)

~ All models will also operate from a regulated and ﬁltered 110 to 340Vdc input.

EMI (All models)

Class B

Meets CISPR Pub. 22 & FCC

Pending

Unless otherwise speciﬁed, load regulation is measured with the output under

test undergoing a load change of 100% to 50% at nominal line input and,

when applicable, with all other outputs operating at 50% of rated load.

Safety Approvals

Transient response is deﬁned as the output returning to within its speciﬁed

tolerance in 10ms or less, following a 90% load change.

DC Outputs

Line Regulation (All outputs)

0.1ꢀ (max)

Load Regulation:

V1 (All models)

V2 & V3 (All models)

2ꢀ

0.2ꢀ (max)

Output Accuracy (Max.):

V1 (All models)

V2 & V3 (All models)

2.0ꢀ

2.5ꢀ

Hold-Up Time (47-63Hz):

@115Vac

@230Vac

20mSec. typ.

80mSec. typ.

Noise & Ripple

(All models, 20MHz bandwidth):

See Noise & Ripple graphs

40mVp-pk (typ.)

V2 & V3

8mVp-pk (typ.)

Transient Response

See Transient Response graphs

www.murata-ps.com

Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000

MPM_DMS-PS-CM.B02 Page 2 of 8

DMS-PS-CM Series

High Efﬁciency, AC/DC Instrumentation Power

Supplies with Individually Isolated Outputs

Ordering Information and Selection Guide

MPS Part No.

DMS-PS1-CM

DMS-PS2-CM

DMS-PS3-CM

DMS-PS4-CM

DMS-PS5-CM

DMS-PS6-CM

DMS-PS7-CM

DMS-PS8-CM

DMS-PS9-CM

DMS-PS10-CM

~ Efﬁciency typical @120V/60Hz

Rated Power

5 Watts

Efﬁciency ~

75ꢀ

V1 Output

5Vdc/1A

V2 Output

—

V3 Output

—

5 Watts

73ꢀ

5Vdc/0.65A

5Vdc/0.35A

24Vdc/0.45A

24Vdc/0.35A

24Vdc/0.30A

24Vdc/0.70A

24Vdc/0.60A

24Vdc/0.55A

12Vdc/1.35A

4.85Vdc/0.2A

—

5 Watts

71ꢀ

4.85Vdc/0.2A

10 Watts

16 Watts

80ꢀ

—

75ꢀ

4.85Vdc/0.2A

—

73ꢀ

4.85Vdc/0.2A

82ꢀ

—

76ꢀ

4.85Vdc/0.2A

—

4.85Vdc/0.2A

—

74ꢀ

82ꢀ

3. Fuse Replacement: If any dc-output drops to zero volts, and no fault

conditions exist within the external load circuitry or the ac mains, F1 may

have failed. F1 is located on the circuit (etch) side of the pc-board. Fuse

replacement is performed by ﬁrst de-energizing and then disconnecting

the ac mains from TB4. Next, disconnect all load wiring from TB1, TB2,

and TB3. Lastly, remove the four screws that secure the pc-board to the

plastic case. After making sure that the new fuse is securely attached to its

mounting clips, re-assemble the unit using all four screws. Reconnect all

input and output wiring and re-apply ac power.

TECHNICAL NOTES

IMPORTANT! To ensure safe and reliable operation, DMS-PS-CM

power supplies must be installed and serviced by qualiﬁed

personnel. Contact Murata Power Solutions if there is any doubt

regarding their installation and/or operation. Please read all of the

following technical and application notes BEFORE installing or

making connections to DMS-PS-CM power supplies.

Warnings (Marking)

If the unit still does not operate properly, and the ac supply at TB4 is

measured to be within its speciﬁed operating range, the power supply

is defective and must be replaced. Except for F1, DMS-PS-CM supplies

contain no other user-serviceable components.

Caution, unit may become hot in normal operation, thereby creat-

ing a potential burn hazard. Disconnect ac mains and then allow

unit to cool before servicing.

Reference document: IEC 417, No. 5041.

4. Wire Gauges and Fusing: All wiring connected to the DMS-PS-CM’s

terminal blocks must meet the requirements speciﬁed in the Functional

Speciﬁcations section. All ac supply and load wiring must be rated for the

voltages and currents they will conduct and must comply with any code

or application-mandated requirements pertaining to the user’s speciﬁc

installation. Applications subject to vibration should include adequate strain

reliefs on both input and output wiring. Install the strain reliefs within 2-3

inches (5-7.5cm) of the terminal blocks.

Dangerous, potentially lethal voltages are present during normal

operation. Disconnect ac mains before servicing.

Reference document: IEC 417, No. 5036.

Caution, refer to accompanying documents for more informa-

tion. Reference document: ISO 3864, No. B.3.1.

It is recommended that all wiring be rated for 600V and 105°C operation

(UL1015 type, for example). Also, wire insulation must be stripped to within

10ꢀ of the dimensions shown in Figure 2. All wires must be inserted

into their respective terminal blocks such that the screw terminal does not

pinch their insulation. No more than two wires should be connected to

any single terminal on TB1 through TB4. If two wires are attached to a

single terminal, be sure to use only two 20AWG (0.5mm²) wires on TB1,

TB2, and TB3, and only two 18 or 20AWG (0.75 or 0.5mm²) wires on TB4.

1. Shock Hazard: DMS-PS-CM Series power supplies feature touch-proof

terminals blocks and fully-isolated plastic construction, thereby greatly reduc-

ing the risk of electrical shock. However, these are mains-powered devices

whose operation is derived from hazardous and potentially lethal voltages.

All service and installation must be performed by qualiﬁed personnel, with

the ac supply voltage de-energized. Before making connections to any of

the unit’s terminal blocks, use a digital voltmeter to verify that the ac supply is

de-energized (off).

2. AC Supply Fuse (F1): All DMS-PS-CM Series power supplies are equipped

with a built-in 1A/250V time-lag fuse. Replacement fuses must be of the

same type and rating; please refer to the Functional Speciﬁcations section

of this datasheet for more information. F1 is conservatively rated in order

to reduce nuisance tripping which might occur during power-up or output

overload conditions. However, F1 is primarily intended to provide protection in

the event of catastrophic failure in the DMS-PS-CM’s ac/dc converter.

0.25"

(6.4mm)

Figure 2. Insulation Strip Length

www.murata-ps.com

Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000

MPM_DMS-PS-CM.B02 Page 3 of 8

DMS-PS-CM Series

High Efﬁciency, AC/DC Instrumentation Power

Supplies with Individually Isolated Outputs

The ac-mains circuit supplying power to DMS-PS-CM supplies must be fused

according to the current rating of the wire gauge used, in accordance with

applicable regulatory codes. The built-in 1ampere line fuse (F1) only protects

the module itself from destructive over currents.

adversely affect the operation and stability of auxiliary outputs V2 and

V3. On these models, V1 must be adjusted to within 2 % of its nominal

value (+5.0V, +12.0V, or +24.0V, depending on model).

9. Temperature Derating (See Figure 3): All DMS-PS-CM supplies are speci-

ﬁed to operate at their full rated power over the temp range of 0°C to +50°C

in still air (convection cooling) without any thermal derating. For operation

over +50°C in still air, derate the output power linearly by 2.5ꢀ per °C down

to 50ꢀ rated power at +70°C. To operate the units at full rated power between

+50°C and +70°C, a minimum forced-airﬂow of 100 LFM is required. For

operation below 0°C, derate the output power linearly by 2.0ꢀ per °C down

to 50ꢀ rated power at –25°C.

5. AC Mains Connections (TB4): To ensure EMI-compliant operation, all three

ac-supply inputs must be properly connected to TB4. Never operate any DMS-

PS-CM power supply without a ground connection to TB4’s ‘FG’ terminal.

On 120Vac 50/60Hz mains, connect the black or "hot" lead to ‘AC(L)’, the

white or “neutral” lead to ‘AC(N)’, and the supply ground (earth) to ‘FG’ (Frame

Ground). On 220V 50/60Hz ac mains with line and neutral conductor-designa-

tions, connect the line to AC(L), the neutral to AC(N), and the ground to ‘FG’.

Unless forced air with the velocity noted above is employed, DMS-PS-CM

supplies should never be mounted upside down (terminal blocks facing

down). Also, always provide sufﬁcient clearances in order to ensure adequate

airﬂow around the supply.

6. Connector Torque Ratings: It is extremely important to tighten all input and

output terminal blocks securely. TB4’s screw terminals must be torqued to

4.4 pound-inches (0.5Nm). TB1, TB2, and TB3 must be torqued to 3.6 pound-

inches (0.4Nm). Proper tightening will minimize losses and ensure safe,

reliable operation.

10.V1 Peak Capabilities: DMS-PS-CM power supplies have a maximum

continuous output-current rating that’s speciﬁed in the Ordering and Selection

Guide. In addition, each model’s V1 output can intermittently supply 120ꢀ of

its continuous rated current for short periods of time if the duty cycle is less

than 10ꢀ. Peak current ratings do not apply to the auxiliary outputs V2 or V3.

7. ‘Power On’ LED: The Power On LED indicates that the unit has ac-power

applied and its V1 dc-output is operational. However, the power-on LED’s

illumination does not imply nor guarantee that the unit’s dc-outputs are within

their speciﬁed accuracy.

11. Isolated Outputs: Unlike the majority of competitive ac/dc power supplies,

all dual- and triple-output DMS-PS-CM power supplies feature fully-isolated

outputs. This is an important feature when, for reasons of high common mode

voltages, an instrument’s input circuit must be isolated from the system ground.

All V1 outputs are isolated from the ac mains by a minimum of 3000Vac, while

auxiliary outputs V2 and V3 are isolated from one another by 2000Vdc, and

fromV1 by 1000Vdc. The low noise, double-isolated auxiliaries are ideal for

powering sensitive instrumentation that requires low ac leakage-currents.

8. Output Adjustment: The main output, V1, on all 5, 10, and 16W models is

adjustable by approximately –10ꢀ to +15ꢀ. V1’s adjustment potentiometer

is accessed via a small hole located next to the Power-On LED. While not

recommended, ﬁeld adjustment of single-output models can be performed

within the tolerance window noted above. However, keep in mind that the

unit’s maximum output power capability must not be exceeded. For example,

increasing V1’s output voltage by 10ꢀ produces a corresponding 10ꢀ reduc-

tion in V1’s maximum output current.

All ac/dc and dc/dc power components utilized in the construction of DMS-

PS-CM power supplies are 100ꢀ hi-pot tested during their manufacturing pro-

cesses. In addition, after ﬁnal assembly by MPS, all models are subjected to an

additional hi-pot testing consisting of 1000Vac sequentially applied between the

ac mains input and each output, and between each output and all other outputs.

On dual-and triple-output units, V1 is factory calibrated with all outputs

simultaneously loaded to 100% of their rated current. On all dual- and

triple output models, adjusting V1 under any condition other than

those just noted (i.e., all outputs loaded to their full rated current) will

2.0% / ºC

1 0 0

2.5% / ºC

7 5

5 0

2 5

70ºC

–25 –10

Figure 3. Temperature Derating

www.murata-ps.com

Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000

MPM_DMS-PS-CM.B02 Page 4 of 8

DMS-PS-CM Series

High Efﬁciency, AC/DC Instrumentation Power

Supplies with Individually Isolated Outputs

3. Model Selection & Energy Conservation: In order to achieve the lowest

possible energy consumption, be sure to determine your application’s total

current requirements. This is especially true when using DMS-PS-CM

supplies to power DATEL’s energy-efﬁcient LED and/or LCD display digital

panel meters (DPMs) and process monitors. In general, choose a power

supply that will accommodate your maximum current consumption plus a

20ꢀ margin. Choosing the lowest-wattage model suitable for a given appli-

cation will provide lower procurement costs and lower long-term operating

costs.

Application Information

1. Chassis Mounting Considerations: In order to minimize self-heating,

DMS-PS-CM power supplies should always be mounted in either a

vertical or horizontal position. Avoid mounting units upside-down or in

close proximity to other heat-generating devices. Also, be sure to use

the mounting hardware described in Figure 4 below in order to ensure

a secure, vibration-resistant installation.

When calculating total current requirements in installations employing

three or more DMS-Series meters, it is acceptable practice to use each

meter’s typical current consumption rating. However, be sure to consult

the relevant product datasheets for all instrumentation comprising your

application.

Screw,

Split Lock Washer,

Flat Washer

Panel/Chassis

Threaded

For applications where DMS-PS-CM power supplies will be powering only

Murata Power Solution’s DPM’s, a 5-Watt DMS-PS3-CM can power up

to four, standard intensity (‘-RS’ sufﬁx) red-LED DMS-30PC meters: two

meters on V1, and one meter each on V2 and V3. The same DMS-PS3-CM

could also be used to power over 40 low-power red DMS-30PC meters

(‘-RL’ sufﬁx), or over 800 DMS-30LCD non-backlit meters! Of course, these

statements are made without regard to ground-loop problems that may be

encountered when powering 800 DPM’s from a single power supply.

Hole

Screw,

Flat Washer

Panel/Chassis

Flat Washer,

Split Lock Washer,

Nut

Hole

Figure 4. Chassis Mounting

Scope Probe

2. Bipolar Operation (See Figure 5): DMS-PS-CM power supplies’ fully

isolated outputs allow for the generation of bipolar (positive and nega-

tive) supply voltages. Bipolar outputs can be used to power dual-supply

operational ampliﬁers, as well as any other type of instrumentation that

requires bipolar supply voltages. However, please keep in mind that

when connecting and operating any two outputs in this fashion, each

output retains its maximum current rating.

Oscilloscope

–

BW = 20MHz

DMS-PS-CM

DMS-PS6-CM

–

Figure 6. Measuring Ripple and Noise

+24V –5V

COM

+5V

Figure 5. Bipolar Connections

www.murata-ps.com

Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000

MPM_DMS-PS-CM.B02 Page 5 of 8

DMS-PS-CM Series

High Efﬁciency, AC/DC Instrumentation Power

Supplies with Individually Isolated Outputs

Typical Performance Curves TA = +25°C, VIN = 120V @60Hz

Noise and Ripple - 100% Load, 20MHz Bandwidth

DMS-PS3-CM

V1 (+5V)

DMS-PS6-CM

V1 (+24V)

DMS-PS9-CM

V1 (+24V)

DMS-PS3-CM

V2 (+4.85V)

DMS-PS6-CM

V2 (+4.85V)

DMS-PS9-CM

V2 (+4.85V)

www.murata-ps.com

Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000

MPM_DMS-PS-CM.B02 Page 6 of 8

DMS-PS-CM Series

High Efﬁciency, AC/DC Instrumentation Power

Supplies with Individually Isolated Outputs

Typical Performance Curves TA = +25°C, VIN = 120V @60Hz

Transient Response - 10% to 100% Load Step

DMS-PS3-CM

V1 (+5V)

DMS-PS6-CM

V1 (+24V)

DMS-PS9-CM

V1 (+24V)

DMS-PS3-CM

V2 (+4.85V)

DMS-PS6-CM

V2 (+4.85V)

DMS-PS9-CM

V2 (+4.85V)

Mechanical Dimensions: Inches (mm) Tolerances: 2 PL DEC 0.02 ( 0.51), 3 PL DEC 0.010 ( 0.254)

www.murata-ps.com

Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000

MPM_DMS-PS-CM.B02 Page 7 of 8

DMS-PS-CM Series

High Efﬁciency, AC/DC Instrumentation Power

Supplies with Individually Isolated Outputs

Mechanical Speciﬁcations

MECHANICAL DIMENSIONS: Inches (mm)

5 Watt &

10 Watt Models

16 Watt Models

TOLERANCES: 2 PL DEC 0.02 ( 0.51)

3 PL DEC 0.010 ( 0.254)

Power On

V1 Adjust

Power

Adjust On

Detail

See detail

–

0.188

(4.8)

TB3

DMS-PSX-CM

AC(L)

AC/DC POWER SUPPLY

–

2.835

(72.0)

AC(N)

TB2

TB1

TB4

–

1.42

(36.1)

4.625 (117.5)

5.125 (130.2)

1.000 (25.4)

4.165 (105.8)

5W models: 0.77 (19.6)

10W models: 0.87 (22.1)

16W models: 0.93 (23.6)

0.125

(3.2)

USA:

Mansﬁeld (MA), Tel: (508) 339-3000, email: sales@murata-ps.com

Toronto, Tel: (866) 740-1232, email: toronto@murata-ps.com

Canada:

UK:

Milton Keynes, Tel: +44 (0)1908 615232, email: mk@murata-ps.com

Montigny Le Bretonneux, Tel: +33 (0)1 34 60 01 01, email: france@murata-ps.com

München, Tel: +49 (0)89-544334-0, email: munich@murata-ps.com

Murata Power Solutions, Inc.

11 Cabot Boulevard, Mansﬁeld, MA 02048-1151 U.S.A.

Tel: (508) 339-3000 (800) 233-2765 Fax: (508) 339-6356

www.murata-ps.com email: sales@murata-ps.com ISO 9001 and 14001 REGISTERED

France:

Germany:

Japan:

Tokyo, Tel: 3-3779-1031, email: sales_tokyo@murata-ps.com

Osaka, Tel: 6-6354-2025, email: sales_osaka@murata-ps.com

11/24/08

Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other

technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply

the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Speciﬁcations are subject to change without

China:

Shanghai, Tel: +86 215 027 3678, email: shanghai@murata-ps.com

Guangzhou, Tel: +86 208 221 8066, email: guangzhou@murata-ps.com

notice.

Singapore: Parkway Centre, Tel: +65 6348 9096, email: singapore@murata-ps.com

www.murata-ps.com

Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000

MPM_DMS-PS-CM.B02 Page 8 of 8

DMS-PS3-CM [MURATA]

相关型号：

DMS-PS4-CM

DMS-PS4-CM-C

DMS-PS5-CM

DMS-PS6-CM

DMS-PS7-CM

DMS-PS7-CM-C

DMS-PS8-CM

DMS-PS9-CM

DMS-SA16-00A1E

DMS-SA16-00A2E

DMS-SA16_15

DMS-ST06-40A1E