EVAL-ADV7189EBM [ADI]
Multiformat SDTV Video Decoder; 多格式SDTV视频解码器型号: | EVAL-ADV7189EBM |
厂家: | ADI |
描述: | Multiformat SDTV Video Decoder |
文件: | 总104页 (文件大小:889K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Multiformat SDTV Video Decoder
ADV7189
0.5 V to 1.6 V analog signal input range
Differential gain: 0.4% typ
Differential phase: 0.4° typ
FEATURES
Multiformat video decoder supports NTSC-(M,N, 4.43),
PAL-(B/D/G/H/I/M/N), SECAM
Programmable video controls:
Integrates three 54 MHz, Noise Shaped Video®, 12-bit ADCs
Clocked from a single 27 MHz crystal
Line-locked clock compatible (LLC)
Adaptive-Digital-Line-Length-Tracking (ADLLT™)
5-line adaptive comb filters
Proprietary architecture for locking to weak, noisy, and
unstable video sources such as VCRs and tuners
Subcarrier frequency lock and status information output
Integrated AGC with adaptive peak white mode
Macrovision® copy protection detection
CTI (chroma transient improvement)
DNR (digital noise reduction)
Multiple programmable analog input formats:
CVBS (composite video)
S-Video (Y/C)
Peak-white/hue/brightness/saturation/contrast
Integrated on-chip video timing generator
Free run mode (generates stable video ouput with no I/P)
VBI decode support for
Close captioning, WSS, CGMS, EDTV, Gemstar® 1×/2×
Power-down mode
2-wire serial MPU interface (I2C® compatible)
3.3 V analog, 1.8 V digital core; 3.3 V IO supply
80-lead LQFP Pb-free package
APPLICATIONS
High end DVD recorders
Video projectors
HDD-based PVRs/DVDRs
LCD TVs
YPrPb component (VESA, MII, SMPTE, and BetaCam)
12 analog video input channels
Set-top boxes
Automatic NTSC/PAL/SECAM identification
Digital output formats (8-bit/10-bit/16-bit/20-bit):
ITU-R BT.656 YCrCb 4:2:2 output + HS, VS, and FIELD
Professional video products
AVR receiver
GENERAL DESCRIPTION
video signal peak-to-peak range of 0.5 V up to 1.6 V.
Alternatively, these can be bypassed for manual settings.
The ADV7189 integrated video decoder automatically detects
and converts a standard analog baseband television signal
compatible with worldwide standards NTSC, PAL, and SECAM
into 4:2:2 component video data compatible with 20-/16-/10-/
8-bit CCIR601/CCIR656.
The fixed 54 MHz clocking of the ADCs and datapath for all
modes allows very precise, accurate sampling and digital
filtering. The line-locked clock output allows the output data
rate, timing signals, and output clock signals to be synchronous,
asynchronous, or line locked even with 5ꢀ line length
variation. The output control signals allow glueless interface
connections in almost any application. The ADV7189 modes
are set up over a 2-wire, serial, bidirectional port (I2C
compatible).
The advanced and highly flexible digital output interface
enables performance video decoding and conversion in line-
locked clock based systems. This makes the device ideally suited
for a broad range of applications with diverse analog video
characteristics, including tape based sources, broadcast sources,
security/surveillance cameras, and professional systems.
The ADV7189 is fabricated in a 3.3 V CMOS process. Its
monolithic CMOS construction ensures greater functionality
with lower power dissipation.
The 12-bit accurate A/D conversion provides professional
quality video performance and is unmatched. This allows true
10-bit resolution in the 10-bit output mode.
The ADV7189 is packaged in a small 80-lead LQFP Pb-free
package.
The 12 analog input channels accept standard Composite, S-
Video, YPrPb video signals in an extensive number of
combinations. AGC and clamp restore circuitry allow an input
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.326.8703
www.analog.com
© 2004 Analog Devices, Inc. All rights reserved.
ADV7189
TABLE OF CONTENTS
Introduction ...................................................................................... 4
Analog Front End......................................................................... 4
Standard Definition Processor ................................................... 4
Functional Block Diagram .............................................................. 5
Specifications..................................................................................... 6
Electrical Characteristics............................................................. 6
Video Specifications..................................................................... 7
Timing Specifications .................................................................. 8
Analog Specifications................................................................... 8
Thermal Specifications ................................................................ 8
Timing Diagrams.......................................................................... 9
Absolute Maximum Ratings.......................................................... 10
ESD Caution................................................................................ 10
Pin Configuration and Function Descriptions........................... 11
Analog Front End ........................................................................... 13
Analog Input Muxing ................................................................ 13
Global Control Registers ............................................................... 16
Power-Save Modes...................................................................... 16
Reset Control .............................................................................. 16
Global Pin Control..................................................................... 17
Global Status Registers................................................................... 19
Identification............................................................................... 19
Status 1 ......................................................................................... 19
Status 2 ......................................................................................... 20
Status 3 ......................................................................................... 20
Standard Definition Processor (SDP).......................................... 21
SD Luma Path ............................................................................. 21
SD Chroma Path......................................................................... 21
SDP Sync Processing.................................................................. 22
SDP VBI Data Recovery............................................................ 22
SDP General Setup..................................................................... 22
SDP Color Controls ................................................................... 25
SDP Clamp Operation............................................................... 27
SDP Luma Filter ......................................................................... 28
SDP Chroma Filter..................................................................... 31
SDP Gain Operation.................................................................. 32
SDP Chroma Transient Improvement (CTI).......................... 36
SDP Digital Noise Reduction (DNR) ...................................... 37
SDP Comb Filters....................................................................... 37
SDP AV Code Insertion and Controls..................................... 40
SDP Synchronization Output Signals...................................... 42
SDP Sync Processing.................................................................. 51
SDP VBI Data Decode............................................................... 52
Pixel Port Configuration ............................................................... 63
MPU Port Description................................................................... 64
Register Accesses ........................................................................ 65
Register Programming............................................................... 65
I2C Sequencer.............................................................................. 65
I2C Control Register Map.......................................................... 66
I2C Register Map Details ........................................................... 70
Appendix A...................................................................................... 97
I2C Programming Examples ..................................................... 97
Appendix B.................................................................................... 100
PCB Layout Recommendations ............................................. 100
Appendix C ................................................................................... 102
Typical Circuit Connection .................................................... 102
Outline Dimensions..................................................................... 104
Ordering Guide ........................................................................ 104
Rev. A | Page 2 of 104
ADV7189
REVISION HISTORY
Revision A
6/04—Changed from Rev. 0 to Rev. A.
Addition to Applications List...........................................................1
Change to Electrical Characteristics...............................................6
Changes to Table 3 ............................................................................8
Changes to Table 5 ............................................................................8
Change to Drive Strength Selection (Data) Section ...................17
Changes to Figure 42 ....................................................................103
Revision 0
5/04—Revision 0: Initial Version
Rev. A | Page 3 of 104
ADV7189
INTRODUCTION
The ADV7189 is a high quality, single chip, multiformat video
decoder that automatically detects and converts PAL, NTSC,
and SECAM standards in the form of composite, S-Video, and
component video into a digital ITU-R BT.656 format.
STANDARD DEFINITION PROCESSOR
The ADV7189 is capable of decoding a large selection of
baseband video signals in composite, S-Video, and component
formats. The video standards supported by the SDP include
PAL B/D/I/G/H, PAL60, PAL M, PAL N, PAL Nc, NTSC M/J,
NTSC 4.43, and SECAM B/D/G/K/L. The ADV7189 can
automatically detect the video standard and process it
accordingly.
The advanced and highly flexible digital output interface
enables performance video decoding and conversion in line-
locked clock based systems. This makes the device ideally suited
for a broad range of applications with diverse analog video
characteristics, including tape based sources, broadcast sources,
security/surveillance cameras, and professional systems.
The ADV7189 has a 5-line, superadaptive, 2D comb filter that
gives superior chrominance and luminance separation when
decoding a composite video signal. This highly adaptive filter
automatically adjusts its processing mode according to video
standard and signal quality with no user intervention required.
Video user controls such as brightness, contrast, saturation, and
hue are also available within the ADV7189.
ANALOG FRONT END
The ADV7189 analog front end comprises three 12-bit Noise
Shaped Video ADCs that digitize the analog video signal before
applying it to the standard definition processor. The analog
front end employs differential channels to each ADC to ensure
high performance in mixed signal applications.
The ADV7189 implements a patented adaptive-digital-line-
length-tracking (ADLLT) algorithm to track varying video line
lengths from sources such as a VCR. ADLLT enables the
ADV7189 to track and decode poor quality video sources such
as VCRs, noisy sources from tuner outputs, VCD players, and
camcorders. The ADV7189 contains a chroma transient
improvement (CTI) processor that sharpens the edge rate of
chroma transitions, resulting in sharper vertical transitions.
The front end also includes a 12-channel input mux that enables
multiple video signals to be applied to the ADV7189. Current
and voltage clamps are positioned in front of each ADC to
ensure that the video signal remains within the range of the
converter. Fine clamping of the video signals is performed
downstream by digital fine clamping within the ADV7189. The
ADCs are configured to run in 4× oversampling mode.
The SDP can process a variety of VBI data services, such as
closed captioning (CC), wide screen signaling (WSS), copy
generation management system (CGMS), EDTV, Gemstar
1×/2×, and extended data service (XDS). The ADV7189 is fully
Macrovision certified; detection circuitry enables Type I, II, and
III protection levels to be identified and reported to the user.
The decoder is also fully robust to all Macrovision signal inputs.
Rev. A | Page 4 of 104
ADV7189
FUNCTIONAL BLOCK DIAGRAM
0 4 8 1 9 - 0 - 0 0 1
R
U T F O O R U M T A P T T E
Figure 1.
Rev. A | Page 5 of 104
ADV7189
SPECIFICATIONS
Temperature range: TMIN to TMAX, –40°C to +85°C. The min/max specifications are guaranteed over this range.
ELECTRICAL CHARACTERISTICS
At AVDD = 3.15 V to 3.45 V, DVDD = 1.65 V to 2.0 V, DVDDIO = 3.0 V to 3.6 V, PVDD = 1.65 V to 2.0 V (operating temperature range, unless
otherwise noted).
Table 1.
Parameter
Symbol
Test Conditions
Min
Typ
Max
Unit
STATIC PERFORMANCE
Resolution (Each ADC)
Integral Nonlinearity
Differential Nonlinearity
DIGITAL INPUTS
N
INL
DNL
12
±±
–0.95/+2
Bits
LSB
LSB
BSL at 54 MHz
BSL at 54 MHz
–2.0/+2.5
–0.75/+0.9
Input High Voltage
Input Low Voltage
Input Current
VIH
VIL
IIN
2
V
V
µA
µA
pF
0.±
Pins listed in Note 1
All other pins
–50
–10
+50
+10
10
Input Capacitance
CIN
DIGITAL OUTPUTS
Output High Voltage
Output Low Voltage
High Impedance Leakage Current
VOH
VOL
ILEAK
ISOURCE = 0.4 mA
ISINK = 3.2 mA
Pins listed in Note 2
All other pins
2.4
V
V
µA
µA
pF
0.4
50
10
20
Output Capacitance
POWER REQUIREMENTS3
Digital Core Power Supply
Digital I/O Power Supply
PLL Power Supply
Analog Power Supply
Digital Core Supply Current
Digital I/O Supply Current
PLL Supply Current
COUT
DVDD
DVDDIO
PVDD
AVDD
IDVDD
IDVDDIO
IPVDD
1.65
3.0
1.65
3.15
1.±
3.3
1.±
3.3
±2
2
10.5
±5
2
V
V
V
V
mA
mA
mA
mA
mA
mA
ms
3.6
2.0
3.45
Analog Supply Current
IAVDD
CVBS input4
YPrPb input5
1±0
1.5
20
Power-Down Current
Power-Up Time
IPWRDN
tPWRUP
1 Pins 36 and 79.
2 Pins 1, 2, 5, 6, 7, ±, 12, 17, 1±, 19, 20, 21, 22, 23, 24, 32, 33, 34, 35, 73, 74, 75, 76, and ±0.
3 Guaranteed by characterization.
4 ADC1 powered on.
5 All three ADCs powered on.
Rev. A | Page 6 of 104
ADV7189
VIDEO SPECIFICATIONS
Guaranteed by characterization. At AVDD = 3.15 V to 3.45 V, DVDD = 1.65 V to 2.0 V, DVDDIO = 3.0 V to 3.6 V, PVDD = 1.65 V to 2.0 V
(operating temperature range, unless otherwise noted).
Table 2.
Parameter
Symbol
Test condition
Min
Typ
Max
Unit
NONLINEAR SPECIFICATIONS
Differential Phase
Differential Gain
Luma Nonlinearity
NOISE SPECIFICATIONS
SNR Unweighted
DP
DG
LNL
CVBS I/P, modulate 5-step
CVBS I/P, modulate 5-step
CVBS I/P, 5-step
0.4
0.4
0.4
0.6
0.6
0.7
°
%
%
Luma ramp
61
63
63
65
60
dB
dB
Luma flat field
Analog Front End Crosstalk
LOCK TIME SPECIFICATIONS
Horizontal Lock Range
Vertical Lock Range
–5
40
+5
70
%
Hz
Fsc Subcarrier Lock Range
Color Lock In Time
Sync Depth Range
±1.3
60
Hz
Lines
%
20
5
200
200
Color Burst Range
%
Vertical Lock Time
2
100
Fields
Lines
Autodetection Switch Speed
CHROMA SPECIFICATIONS
Hue Accuracy
Color Saturation Accuracy
Color AGC Range
Chroma Amplitude Error
Chroma Phase Error
Chroma Luma Intermodulation
LUMA SPECIFICATIONS
Luma Brightness Accuracy
Luma Contrast Accuracy
HUE
CL_AC
1
1
°
%
%
%
°
5
400
0.4
0.3
0.1
%
CVBS, 1 V I/P
CVBS, 1 V I/P
1
1
%
%
Rev. A | Page 7 of 104
ADV7189
TIMING SPECIFICATIONS
Guaranteed by characterization. At AVDD = 3.15 V to 3.45 V, DVDD = 1.65 V to 2.0 V, DVDDIO = 3.0 V to 3.6 V, PVDD = 1.65 V to 2.0 V
(operating temperature range, unless otherwise noted).
Table 3.
Parameter
Symbol
Test Conditions
Min
Typ
Max
Unit
SYSTEM CLOCK AND CRYSTAL
Nominal Frequency
Frequency Stability
I2C PORT
SCLK Frequency
27.00
MHz
ppm
±50
400
kHz
µs
µs
µs
µs
ns
ns
ns
µs
SCLK Min Pulse Width High
SCLK Min Pulse Width Low
Hold Time (Start Condition)
Setup Time (Start Condition)
SDA Setup Time
SCLK and SDA Rise Time
SCLK and SDA Fall Time
Setup Time for Stop Condition
RESET FEATURE
t1
t2
t3
t4
t5
t6
t7
t±
0.6
1.3
0.6
0.6
100
300
300
0.6
Reset Pulse Width
5
ms
CLOCK OUTPUTS
LLC1 Mark Space Ratio
LLC1 Rising to LLC2 Rising
LLC1 Rising to LLC2 Falling
DATA and CONTROL OUTPUTS
Data Output Transitional Time
Data Output Transitional Time
Propagation Delay to Hi Z
Max Output Enable Access Time
Min Output Enable Access Time
t9:t10
t11
t12
45:55
55:45
% Duty Cycle
ns
ns
0.5
0.5
t13
t14
t15
t16
t17
tACCESS = t10 – t13
tHOLD = t9 + t14
6
−0.6
ns
ns
ns
ns
ns
6
7
4
ANALOG SPECIFICATIONS
Guaranteed by characterization. At AVDD = 3.15 V to 3.45 V, DVDD = 1.65 V to 2.0 V, DVDDIO = 3.0 V to 3.6 V, PVDD = 1.65 V to 2.0 V
(operating temperature range, unless otherwise noted).
Table 4.
Parameter
Symbol
Test condition
Min
Typ
Max
Unit
CLAMP CIRCUITRY
External Clamp Capacitor
Input Impedance
Large Clamp Source Current
Large Clamp Sink Current
Fine Clamp Source Current
Fine Clamp Sink Current
0.1
10
0.75
0.75
60
µF
Clamps switched off
MΩ
mA
mA
µA
60
µA
THERMAL SPECIFICATIONS
Table 5.
Parameter
Symbol Test Conditions
Min Typ Max Unit
THERMAL CHARACTERISTICS
Junction-to-Case Thermal Resistance
Junction-to-Ambient Thermal Resistance (Still Air)
θJC
θJA
4-layer PCB with solid ground plane
4-layer PCB with solid ground plane
7.6
3±.1
°C/W
°C/W
Rev. A | Page ± of 104
ADV7189
TIMING DIAGRAMS
t5
t3
t3
SDA
t1
t6
SCLK
t4
t7
t8
t2
Figure 2. I2C Timing
t9
t10
OUTPUT LLC1
OUTPUT LLC2
t11
t12
t13
t14
OUTPUTS P0–P19, VS,
HS, FIELD,
SFL/SYNC_OUT
Figure 3. Pixel Port and Control Output Timing
OE
t15
t17
P0–P19, HS,
VS, FIELD,
SFL/SYNC_OUT
t16
Figure 4.
OE
Timing
Rev. A | Page 9 of 104
ADV7189
ABSOLUTE MAXIMUM RATINGS
Table 6.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to
absolute maximum rating conditions for extended periods may
affect device reliability.
Parameter
Rating
AVDD to GND
4 V
AVDD to AGND
4 V
DVDD to DGND
2.2 V
PVDD to AGND
2.2 V
DVDDIO to DGND
4 V
DVDDIO to AVDD
PVDD to DVDD
DVDDIO – PVDD
DVDDIO – DVDD
AVDD – PVDD
AVDD – DVDD
Digital Inputs Voltage to DGND
Digital Output Voltage to DGND
Analog Inputs to AGND
Maximum Junction Temperature
–0.3 V to +0.3 V
–0.3 V to +0.3 V
–0.3V to +2 V
–0.3V to +2 V
–0.3V to +2 V
–0.3V to +2 V
–0.3V to DVDDIO + 0.3 V
–0.3V to DVDDIO + 0.3 V
AGND – 0.3 V to AVDD + 0.3 V
150°C
(TJMAX
)
Storage Temperature Range
Infrared Reflow Soldering (20 s)
–65°C to +150°C
260°C
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the
human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. A | Page 10 of 104
ADV7189
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
VS
HS
1
2
3
4
5
6
7
8
9
60 AIN5
59 AIN11
58 AIN4
DGND
DVDDIO
P15
57 AIN10
56 AGND
55 CAP C2
54 CAP C1
53 AGND
52 CML
P14
P13
P12
DGND
ADV7189
TOP VIEW
(Not to Scale)
DVDD 10
NC 11
51 REFOUT
50 AVDD
49 CAP Y2
48 CAP Y1
47 AGND
46 AIN3
SFL 12
NC 13
DGND 14
DVDDIO 15
NC 16
45 AIN9
P11 17
P10 18
P9 19
44 AIN2
43 AIN8
42 AIN1
P8 20
41 AIN7
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
NC = NO CONNECT
Figure 5. 80-Lead LQFP Pin Configuration
Table 7. Pin Function Descriptions
Pin No.
Mnemonic
Type Function
3, 9, 14, 31, 71
39, 40, 47, 53,
56
DGND
AGND
G
G
Digital Ground.
Analog Ground.
4, 15
10, 30, 72
50
3±
DVDDIO
DVDD
AVDD
PVDD
AIN1–AIN12
NC
P
P
P
P
I
Digital I/O Supply Voltage (3.3 V).
Digital Core Supply Voltage (1.± V).
Analog Supply Voltage (3.3 V).
PLL Supply Voltage (1.± V).
Analog Video Input Channels.
No Connect Pins.
41–46, 57–62
11, 13, 16, 25,
63, 65, 69, 70,
77, 7±
5–±, 17–24,
P0–P19
O
Video Pixel Output Port.
32–35, 73–76
2
1
±0
67
6±
66
HS
VS
FIELD
SDA
SCLK
ALSB
O
O
O
I/O
I
HS is a horizontal synchronization output signal.
VS is a vertical synchronization output signal.
FIELD is a field synchronization output signal.
I2C Port Serial Data Input/Output Pin.
I2C Port Serial Clock Input (Max Clock Rate of 400 kHz).
I
This pin selects the I2C address for the ADV71±9. ALSB set to a Logic 0 sets the address for a
write as 0x40; for ALSB set to a logic high, the address selected is 0x42.
64
27
26
RESET
LLC1
LLC2
I
System Reset Input, Active Low. A minimum low reset pulse width of 5 ms is required to reset
the ADV71±9 circuitry.
This is a line-locked output clock for the pixel data output by the ADV71±9. Nominally 27 MHz,
but varies up or down according to video line length.
This is a divide-by-2 version of the LLC1 output clock for the pixel data output by the ADV71±9.
Nominally 13.5 MHz, but varies up or down according to video line length.
O
O
Rev. A | Page 11 of 104
ADV7189
Pin No.
Mnemonic
Type Function
29
XTAL
I
This is the input pin for the 27 MHz crystal, or can be overdriven by an external 3.3 V, 27 MHz
clock oscillator source. In crystal mode, the crystal must be a fundamental crystal.
2±
XTAL1
O
This pin should be connected to the 27 MHz crystal or left as a no connect if an external 3.3 V
27 MHz clock oscillator source is used to clock the ADV71±9. In crystal mode, the crystal must
be a fundamental crystal.
36
79
PWRDN
OE
I
I
A logic low on this pin places the ADV71±9 in a power-down mode. Refer to the I2C Control
Register Map section for more options on power-down modes for the ADV71±9.
When set to a logic low, OE enables the pixel output bus, P19–P0 of the ADV71±9. A logic high
on the OE pin places Pins P19–P0, HS, VS, SFL/SYNC_OUT into a high impedance state.
37
12
ELPF
SFL
I
The recommended external loop filter must be connected to this ELPF pin, as shown in
Figure 42.
Subcarrier Frequency Lock. This pin contains a serial output stream that can be used to lock the
subcarrier frequency when this decoder is connected to any Analog Devices, Inc. digital video
encoder.
O
51
52
REFOUT
CML
O
O
Internal Voltage Reference Output. Refer to Figure 42 for a recommended capacitor network
for this pin.
The CML pin is a common-mode level for the internal ADCs. Refer to Figure 42 for a
recommended capacitor network for this pin.
4±, 49
54, 55
CAPY1, CAPY2
CAPC1, CAPC2
I
I
ADC’s Capacitor Network. Refer to Figure 42 for a recommended capacitor network for this pin.
ADC’s Capacitor Network. Refer to Figure 42 for a recommended capacitor network for this pin.
Rev. A | Page 12 of 104
ADV7189
ANALOG FRONT END
ANALOG INPUT MUXING
ADC_SW_MAN_EN
INSEL[3:0]
INTERNAL
MAPPING
FUNCTIONS
AIN1
AIN7
AIN2
AIN8
AIN3
AIN9
AIN4
AIN10
AIN5
AIN11
AIN6
AIN12
ADC0_SW[3:0]
1
0
ADC0
AIN3
AIN9
AIN4
AIN10
AIN5
AIN11
AIN6
AIN12
ADC1_SW[3:0]
1
0
ADC1
ADC1_SW[3:0]
ADC2
AIN2
AIN8
AIN5
AIN11
AIN6
AIN12
1
0
Figure 6. Internal Pin Connections
ADI Recommended Input Muxing
The ADV7189 has an integrated analog muxing section that
allows more than one source of video signal to be connected to
the decoder. Figure 6 outlines the overall structure of the input
muxing provided in ADV7189.
A maximum of 12 CVBS inputs can be connected and decoded
by the ADV7189. As can be seen from Figure 5, this means the
sources will have to be connected to adjacent pins on the IC.
This calls for a careful design of the PCB layout (e.g., ground
shielding between all signals routed through tracks that are
physically close together).
As can be seen in Figure 6, there are two different ways in which
the analog input muxes can be controlled:
1. Control via functional registers (INSEL).
INSEL[3:0] Input Selection, Address 0x00, [3:0]
Using INSEL[3:0] simplifies the setup of the muxes, and
minimizes crosstalk between channels by pre-assigning the
input channels. This is referred to as ADI recommended
input muxing.
The INSEL bits allow the user to select an input channel as well
as the input format. Depending on the PCB connections, only a
subset of the INSEL modes are valid. Please note that the
INSEL[3:0] does not only switch the analog input muxing, it
also configures the standard definition processor core to
process CVBS (Comp), S-video (Y/C), or component (YPbPr)
format.
2. Control via an I2C manual override (ADC_sw_man_en,
ADC0_sw, ADC1_sw, ADC2_sw).
This is provided for applications with special requirements
(e.g., number/combinations of signals) that would not be
served by the pre-assigned input connections. This is
referred to as manual input muxing.
Please refer to Figure 7 for an overview of the two methods of
controlling the ADV7189’s input muxing.
Rev. A | Page 13 of 104
ADV7189
CONNECTING
ANALOG SIGNALS
TO ADV7189
ADI RECOMMENDED
INPUT MUXING; SEE TABLE 9
YES
NO
SET INSEL[3:0] FOR REQUIRED
MUXING CONFIGURATION
SET INSEL[3:0] TO
CONFIGURE ADV7189 TO
DECODE VIDEO FORMAT:
CVBS: 0000
YC: 0110
YPrPb: 1001
USE MANUAL INPUT MUXING
(ADC_SW_MAN_EN, ADC0_SW,
ADC1_SW, ADC2_SW)
Figure 7. Input Muxing Overview
Table 8. Input Channel Switching Using INSEL[3:0]
Table 9. Input Channel Assignments
Description
Input
Channel No.
Pin
ADI Recommended Input Muxing Control
INSEL[3:0]
INSEL[3:0]
0000*
0001
0010
0011
0100
0101
0110
Analog Input Pins
CVBS1 = AIN1
CVBS2 = AIN2
CVBS3 = AIN3
CVBS4 = AIN4
CVBS5 = AIN5
CVBS6 = AIN6
Y1 = AIN1
Video Format (SDP)
Composite
Composite
Composite
Composite
Composite
Composite
YC
YC
YC
YC
YC
AIN7
AIN1
AIN±
AIN2
AIN9
AIN3
AIN10
AIN4
AIN11
AIN5
AIN12
AIN6
41
42
43
44
45
46
57
5±
59
60
61
62
CVBS7
CVBS1
CVBS±
CVBS2
CVBS9
CVBS3
CVBS10
CVBS4
CVBS11
CVBS5
Not Available
CVBS6
YC1-Y
YC2-Y
YC3-Y
YC1-C
YC2-C
YC3-C
YPrPb1-Y
YPrPb2-Y
YPrPb2-Pb
YPrPb1-Pb
YPrPb1-Pr
YPrPb2-Pr
C1 = AIN4
0111
1000
1001
Y2 = AIN2
C2 = AIN5
Y3 = AIN3
C3 = AIN6
Y1 = AIN1
PR1 = AIN4
PB1 = AIN5
Y2 = AIN2
YC
YPrPb
YPrPb
YPrPb
YPrPb
ADI recommended input muxing is designed to minimize
crosstalk between signal channels and to obtain the highest
level of signal integrity. Table 9 summarizes how the PCB layout
should connect analog video signals to the ADV7189.
1010
PR2 = AIN3
YPrPb
PB2 = AIN6
YPrPb
Notes
1011
1100
1101
CVBS7 = AIN7
CVBS± = AIN±
CVBS9 = AIN9
CVBS10 = AIN10
CVBS11 = AIN11
Composite
Composite
Composite
Composite
Composite
•
It is strongly recommended to connect any unused analog
input pins to AGND to act as a shield.
1110
1111
•
Inputs AIN7 to AIN11 should be connected to AGND in
cases where only six input channels are used. This will
improve the quality of the sampling due to better isolation
between the channels.
*Default value.
•
AIN12 is not under the control of INSEL[3:0]. It can only
be routed to ADC0/ADC1/ADC2 by manual muxing. See
Table 10 for further details.
Rev. A | Page 14 of 104
ADV7189
This means INSEL must still be used to tell the ADV7189
whether the input signal is of component, YC, or CVBS
format.
Manual Input Muxing
By accessing a set of manual override muxing registers, the
analog input muxes of the ADV7189 can be controlled directly.
This is referred to as manual input muxing.
There are restrictions in the channel routing imposed by the
analog signal routing inside the IC; every input pin cannot be
routed to each ADC. Please refer to Figure 6 for an overview on
the routing capabilities inside the chip. The three mux sections
can be controlled by the reserved control signal buses
ADC0/ADC1/ADC2_sw[3:0]. Table 10 explains the control
words used.
Notes
•
Manual input muxing overrides other input muxing
control bits (e.g., INSEL)
•
The manual muxing is activated by setting the
ADC_SW_MAN_EN bit. It only affects the analog
switches in front of the ADCs.
SETADC_sw_man_en, Manual Input Muxing Enable,
Address C4, [7]
This means if the settings of INSEL and the manual input
muxing registers (ADC0/1/2_sw) contradict each other,
the ADC0/ADC1/ADC2_sw settings apply and INSEL is
ignored.
ADC0_sw[3:0], ADC0 mux configuration, Address 0xC3, [3:0]
ADC1_sw[3:0], ADC1 mux configuration, Address 0xC3, [7:4]
ADC2_sw[3:0], ADC2 mux configuration, Address 0xC4, [3:0]
•
Manual input muxing only controls the analog input
muxes. INSEL[3:0] still has to be set so the follow-on
blocks process the video data in the correct format.
Table 10. Manual Mux Settings for All ADCs
SETADC_sw_man_en = 1
ADC1_sw[3:0] ADC1 Connected to:
ADC0_sw[3:0]
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
ADC0 Connected to:
No Connection
AIN1
AIN2
AIN3
AIN4
AIN5
AIN6
No Connection
No Connection
AIN7
AIN±
AIN9
AIN10
AIN11
AIN12
No Connection
ADC2_sw[3:0]
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
ADC2 Connected to:
No Connection
No Connection
AIN2
No Connection
No Connection
AIN5
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
No Connection
No Connection
No Connection
AIN3
AIN4
AIN5
AIN6
AIN6
No Connection
No Connection
No Connection
No Connection
AIN9
AIN10
AIN11
AIN12
No Connection
No Connection
No Connection
No Connection
AIN±
No Connection
No Connection
AIN11
AIN12
No Connection
Rev. A | Page 15 of 104
ADV7189
GLOBAL CONTROL REGISTERS
Register control bits listed in this section affect the whole chip.
PWRDN_ADC_0, Address 0x3A, [3]
Table 13. PWRDN_ADC_0 Function
POWER-SAVE MODES
Power-Down
PWRDN_ADC_0
Description
0*
1
ADC normal operation.
Power down ADC 0.
PDBP, Address 0x0F, [2]
*Default value.
There are two ways to shut down the digital core of the
ADV7189: a pin (
) and a bit (PWRDN see below). The
PWRDN
PDBP controls which of the two has the higher priority. The
default is to give the pin ( ) priority. This allows the
PWRDN_ADC_1, Address 0x3A, [2]
Table 14. PWRDN_ADC_1 Function
PWRDN_ADC_1 Description
PWRDN
user to have the ADV7189 powered down by default.
0*
ADC normal operation.
Power down ADC 1.
Table 11. PDBP Function
1
*Default value.
PDBP Description
0*
Digital core power controlled by the PWRDN pin (bit is
disregarded).
Bit has priority (pin is disregarded).
PWRDN_ADC_2, Address 0x3A, [1]
Table 15. PWRDN_ADC_2 Function
1
PWRDN_ADC_2
Description
*Default value.
0*
1
ADC normal operation.
Power down ADC 2.
PWRDN, Address 0x0F, [5]
*Default value.
Setting the PWRDN bit switches the ADV7189 into a chip-wide
power-down mode. The power-down stops the clock from
entering the digital section of the chip, thereby freezing its
operation. No I2C bits are lost during power-down. The
PWRDN bit also affects the analog blocks and switches them
into low current modes. The I2C interface itself is unaffected,
and remains operational in power-down mode.
RESET CONTROL
Chip Reset (RES), Address 0x0F, [7]
Setting this bit, equivalent to controlling the
pin on the
RESET
ADV7189, issues a full chip reset. All I2C registers get reset to
their default values6. After the reset sequence, the part immedi-
ately starts to acquire the incoming video signal.
The ADV7189 leaves the power-down state if the PWRDN bit is
set to 0 (via I2C), or if the overall part is reset using Pin
.
RESET
Notes
Note that PDBP must be set to 1 for the PWRDN bit to power
down the ADV7189.
•
After setting the RES bit (or initiating a reset via the pin),
the part returns to the default mode of operation with
respect to its primary mode of operation. All I2C bits are
loaded with their default values, making this bit self-
clearing.
Table 12. PWRDN Function
PWRDN
Description
0*
Chip operational.
1
ADV71±9 in chip-wide power-down.
•
•
Executing a software reset takes approximately 2 ms.
However, it is recommended to wait 5 ms before any
further I2C writes are performed.
*Default value.
ADC Power-Down Control
The I2C master controller receives a no acknowledge
condition on the ninth clock cycle when Chip Reset is
implemented (see the MPU Port Description section for a
full description).
The ADV7189 contains three 12-bit ADCs (ADC 0, ADC 1, and
ADC 2). If required, it is possible to power down each ADC
individually.
When should the ADCs be powered down?
Table 16. RES Function
RES
•
CVBS mode. ADC 1 and ADC 2 should be powered down
to save on power consumption.
Description
0*
Normal operation.
1
Start reset sequence.
•
S-Video mode. ADC 2 should be powered down to save on
power consumption.
*Default value.
6 Some register bits do not have a reset value specified. They keep their last
written value. Those bits are marked as having a reset value of x in the
register table.
Rev. A | Page 16 of 104
ADV7189
Timing Signals Output Enable
GLOBAL PIN CONTROL
Three-State Output Drivers
TIM_OE, Address 0x04, [3]
TOD, Address 0x03, [6]
The TIM_OE bit should be regarded as an addition to the TOD
bit. Setting it high forces the output drivers for HS, VS, and
FIELD into the active (i.e., driving) state even if the TOD bit is
set. If set to low, the HS, VS, and FIELD pins are three-stated
dependent on the TOD bit. This functionality is useful if the
decoder is to be used as a timing generator only. This may be
the case if only the timing signals are to be extracted from an
incoming signal, or if the part is in free-run mode where a
separate chip can output, for instance, a company logo.
This bit allows the user to three-state the output drivers of the
ADV7189.
Upon setting the TOD bit, the P[19:0], HS, VS, FIELD, and SFL
pins are three-stated.
Note that the timing pins (HS/VS/FIELD) can be forced active
via the TIM_OE bit. For more information on three-state
control, refer to the following sections:
For more information on three-state control, refer to the
following sections:
•
•
Three-State LLC Driver
Timing Signals Output Enable
•
•
Three-State Output Drivers
Three-State LLC Driver.
Individual drive strength controls are provided via the
DR_STR_XX bits.
Individual drive strength controls are provided via the
DR_STR_XX bits.
Note that the ADV7189 supports three-stating via a dedicated
pin. When set high, the
pin three-states the output drivers
OE
Table 19. TIM_OE Function
for P[19:0], HS, VS, FIELD, and SFL. The output drivers are
TIM_OE
Description
three-stated if the TOD bit or the
pin is set high.
OE
0*
1
HS, VS, FIELD three-stated according to the TOD bit.
HS, VS, FIELD are forced active all the time. The
DR_STR_S[1:0] setting determines drive strength.
Table 17. TOD Function
TOD
Description
*Default value.
0*
Output drivers enabled.
1
Output drivers three-stated.
Drive Strength Selection (Data)
*Default value.
Three-State LLC Driver
DR_STR[1:0] Address 0x04, [5:4]
For EMC and crosstalk reasons, it may be desirable to
strengthen or weaken the drive strength of the output drivers.
The DR_STR[1:0] bits affect the P[19:0] output drivers.
TRI_LLC, Address 0x0E, [6]
This bit allows the output drivers for the LLC1 and LLC2 pins
of the ADV7189 to be three-stated. For more information on
three-state control, refer to the following sections:
For more information on three-state control, refer to the
following sections:
•
•
Three-State Output Drivers
Timing Signals Output Enable
•
•
Drive Strength Selection (Clock)
Drive Strength Selection (Sync)
Individual drive strength controls are provided via the
DR_STR_XX bits.
Table 20. DR_STR Function
Table 18. TRI_LLC Function
DR_STR[1:0]
Description
TRI_LLC
Description
00
Low drive strength (1×).
0*
LLC pin drivers working according to the
DR_STR_C[1:0] setting (pin enabled).
LLC pin drivers three-stated.
01*
10
11
Medium low drive strength (2×).
Medium high drive strength (3×).
High drive strength (4×).
1
*Default value.
*Default value.
Rev. A | Page 17 of 104
ADV7189
Drive Strength Selection (Clock)
Enable Subcarrier Frequency Lock Pin
DR_STR_C[1:0] Address 0x0E, [3:2]
EN_SFL_PIN Address 0x04, [1]
The DR_STR_C[1:0] bits can be used to select the strength of
the clock signal output driver (LLC pin). For more information,
refer to the following sections:
The subcarrier frequency lock pin (SDP, output only) has a
double function: it can also output raw sync-related information
(SogOut). The EN_SFL_PIN bit enables the output of
subcarrier lock information (also known as GenLock) from the
SDP core to an encoder in a decoder-encoder back-to-back
arrangement.
•
Drive Strength Selection (Sync)
•
Drive Strength Selection (Data)
Table 23. EN_SFL_PIN Function
EN_SFL_PIN Description
Table 21. DR_STR Function
DR_STR[1:0]
Description
0*
1
Subcarrier frequency lock output is disabled.
Subcarrier frequency lock information is
presented on the SFL pin.
00
Low drive strength (1×).
01*
10
11
Medium low drive strength (2×).
Medium high drive strength (3×).
High drive strength (4×).
*Default value.
*Default value.
Polarity LLC Pin
Drive Strength Selection (Sync)
PCLK Address 0x37, [0]
The polarity of the clock that leaves the ADV7189 via the LLC1
and LLC2 pins can be inverted using the PCLK bit. Note that
this inversion affects the clock for SDP.
DR_STR_S[1:0] Address 0x0E, [1:0]
The DR_STR_S[1:0] bits allow the user to select the strength of
the synchronization signals with which HS, VS, and F are
driven. For more information, refer to the following sections:
Changing the polarity of the LLC clock output may be
necessary to meet the setup-and-hold time expectations of
follow-on chips.
•
Drive Strength Selection (Clock)
Drive Strength Selection (Data)
•
Note that this bit also inverts the polarity of the LLC2 clock.
Table 22. DR_STR Function
Table 24. PCLK Function
DR_STR[1:0]
Description
PCLK
Description
00
01*
10
11
Low drive strength (1×).
0
1*
Invert LLC output polarity.
LLC output polarity normal (as per the Timing
Diagrams)
Medium low drive strength (2×).
Medium high drive strength (3×).
High drive strength (4×).
*Default value.
*Default value.
Rev. A | Page 1± of 104
ADV7189
GLOBAL STATUS REGISTERS
There are four registers that provide summary information
about the video decoder. The IDENT register allows the user to
identify the revision code of the ADV7189. The other three
registers contain status bits from the SDP.
Depending on the setting of the FSCLE bit, the Status[0] and
Status[1] are based solely on horizontal timing info or on the
horizontal timing and lock status of the color subcarrier. See the
FSCLE Fsc Lock Enable (SDP), Address 0x51, [7] section.
SDP Autodetection Result
IDENTIFICATION
AD_RESULT[2:0] Address 0x10, [6:4]
IDENT[7:0] Address 0x11, [7:0]
The AD_RESULT[2:0] bits report back on the findings from the
SDP autodetection block. Consult the SDP General Setup sec-
tion for more information on enabling the autodetection block,
and the Autodetection of SDP Modes section to find out how to
configure it.
Provides identification of the revision of the ADV7189. Please
review the list of IDENT code readback values for the various
versions shown in Table 25.
Table 25. IDENT Function
IDENT[7:0]
0x0F or 0x10
0x11
Description
Table 26. AD_RESULT Function
ADV71±9-FT
ADV71±9 (Version 2)
AD_RESULT[2:0]
Description
000
001
010
011
100
101
110
111
NTSM-MJ
NTSC-443
PAL-M
PAL-60
PAL-BGHID
SECAM
STATUS 1
STATUS_1[7:0] Address 0x10, [7:0]
This read-only register provides information about the internal
status of the ADV7189.
PAL-Combination N
SECAM 525
Please see CIL[2:0] Count Into Lock (SDP), Address 0x51, [2:0]
and COL[2:0] Count Out of Lock (SDP), Address 0x51, [5:3] for
information on the timing.
Table 27. STATUS 1 Function
STATUS 1 [7:0]
Bit Name
Block
SDP
SDP
SDP
SDP
SDP
SDP
SDP
SDP
Description
0
1
2
3
4
5
6
7
IN_LOCK
LOST_LOCK
FSC_LOCK
FOLLOW_PW
AD_RESULT.0
AD_RESULT.1
AD_RESULT.2
COL_KILL
In lock (right now).
Lost lock (since last read of this register).
Fsc locked (right now).
AGC follows peak white algorithm.
Result of SDP autodetection.
Result of SDP autodetection.
Result of SDP autodetection.
Color kill active.
Rev. A | Page 19 of 104
ADV7189
STATUS 2
STATUS_2[7:0], Address 0x12, [7:0]
Table 28. STATUS 2 Function
STATUS 2 [7:0]
Bit Name
MVCS DET
MVCS T3
MV_PS DET
MV_AGC DET
LL_NSTD
Block
SDP
SDP
SDP
SDP
SDP
SDP
Description
0
1
2
3
4
5
6
7
Detected Macrovision color striping.
Macrovision color striping protection. Conforms to Type 3 (if high), and Type 2 (if low).
Detected Macrovision pseudo Sync pulses.
Detected Macrovision AGC pulses.
Line length is nonstandard.
Fsc frequency is nonstandard.
FSC_NSTD
Reserved
Reserved
STATUS 3
STATUS_3[7:0], Address 0x13, [7:0]
Table 29. STATUS 3 Function
STATUS 3 [7:0] Bit Name
Block Description
SDP Horizontal lock indicator (instantaneous).
0
1
2
3
4
INST_HLOCK
Reserved for future use.
Reserved for future use.
Reserved for future use.
SDP outputs a blue screen (see theDEF_VAL_AUTO_EN Default Value Automatic Enable (SDP),
Address 0x0C, [1] section).
FREE_RUN_ACT SDP
5
6
7
STD_FLD_LEN
INTERLACED
PAL_SW_LOCK
SDP
SDP
SDP
Field length is correct for currently selected video standard.
Interlaced video detected (field sequence found).
Reliable sequence of swinging bursts detected.
Rev. A | Page 20 of 104
ADV7189
STANDARD DEFINITION PROCESSOR (SDP)
STANDARD DEFINITION PROCESSOR
MACROVISION
DETECTION
STANDARD
AUTODETECTION
SLLC
CONTROL
VBI DATA
RECOVERY
LUMA
DIGITAL
FINE
DIGITIZED CVBS
DIGITIZED Y (YC)
LUMA
2D COMB
LUMA
FILTER
GAIN
CONTROL
LUMA
RESAMPLE
CLAMP
LINE
AV
SYNC
EXTRACT
RESAMPLE
CONTROL
VIDEO DATA
OUTPUT
LENGTH
CODE
PREDICTOR
INSERTION
CHROMA
DIGITAL
FINE
MEASUREMENT
BLOCK (= >1 C)
DIGITIZED CVBS
DIGITIZED C (YC)
CHROMA
DEMOD
CHROMA
FILTER
GAIN
CONTROL
CHROMA
RESAMPLE
CHROMA
2D COMB
2
CLAMP
VIDEO DATA
PROCESSING
BLOCK
F
SC
RECOVERY
Figure 8. Block Diagram of the Standard Definition Processor
A block diagram of the ADV7189’s standard definition
processor (SDP) is shown in Figure 8.
SD CHROMA PATH
The input signal is processed by the following blocks:
The SDP block can handle standard definition video in CVBS,
YC, and YPrPb formats. It can be divided into a luminance and
chrominance path. If the input video is of a composite type
(CVBS), both processing paths are fed with the CVBS input.
•
Digital Fine Clamp. This block uses a high precision algo-
rithm to clamp the video signal.
•
Chroma Demodulation. This block employs a color sub-
carrier (Fsc) recovery unit to regenerate the color
subcarrier for any modulated chroma scheme. The
demodulation block then performs an AM demodulation
for PAL and NTSC and an FM demodulation for SECAM.
SD LUMA PATH
The input signal is processed by the following blocks:
•
Digital Fine Clamp. This block uses a high precision
algorithm to clamp the video signal.
•
•
Chroma Filter Block. This block contains a chroma
decimation filter (CAA) with a fixed response, and some
shaping filters (CSH) that have selectable responses.
•
Luma Filter Block. This block contains a luma decimation
filter (YAA) with a fixed response, and some shaping filters
(YSH) that have selectable responses.
Gain Control. Automatic gain control (AGC) can operate
on several different modes, including gain based on the
color subcarrier’s amplitude, gain based on the depth of the
horizontal sync pulse on the Luma channel, or fixed
manual gain.
•
•
Luma Gain Control. The automatic gain control (AGC) can
operate on a variety of different modes, including gain
based on the depth of the horizontal sync pulse, peak white
mode, and fixed manual gain.
•
Chroma Resample. The chroma data is digitally resampled
to keep it perfectly aligned with the luma data. The
resampling is done to correct for static and dynamic line-
length errors of the incoming video signal.
Luma Resample. To correct for line-length errors as well as
dynamic line-length changes, the data is digitally
resampled.
•
•
Luma 2D Comb. The two-dimensional comb filter provides
YC separation.
•
•
Chroma 2D Comb. The two-dimensional, 5-line,
superadaptive comb filter provides high quality YC
separation in case the input signal is CVBS.
AV Code Insertion. At this point, the decoded luma (Y)
signal is merged with the retrieved chroma values. AV
codes (as per ITU-R. BT-656) can be inserted.
AV Code Insertion. At this point, the demodulated chroma
(Cr and Cb) signal is merged with the retrieved luma
values. AV codes (as per ITU-R. BT-656) can be inserted.
Rev. A | Page 21 of 104
ADV7189
SDP SYNC PROCESSING
SDP GENERAL SETUP
Video Standard Selection (SDP)
The SDP extracts syncs embedded in the video data stream.
There is currently no support for external HS/VS inputs. The
sync extraction has been optimized to support imperfect video
sources (e.g., videocassette recorders with head switches). The
actual algorithm used employs a coarse detection based on a
threshold crossing followed by a more detailed detection using
an adaptive interpolation algorithm. The raw sync information
is sent to a line-length measurement and prediction block. The
output of this is then used to drive the digital resampling
section to ensure that the SDP outputs 720 active pixels per line.
The VID_SEL[3:0] register allows the user to force the digital
core into a specific video standard. Under normal
circumstances, this should not be necessary. The VID_SEL[3:0]
bits default to an autodetection mode that supports PAL, NTSC,
SECAM, and variants thereof.
Refer to the Autodetection of SDP Modes section for more
information on the autodetection system.
Autodetection of SDP Modes
In order to guide the autodetect system of the SDP block,
individual enable bits are provided for each of the supported
video standards. Setting the relevant bit to 0 inhibits the
standard from being detected automatically. Instead, the system
picks the closest of the remaining enabled standards. The results
of SDP autodetection can be read back via the status registers.
See the Global Status Registers section for more information.
The sync processing on the ADV7189 also includes two
specialized postprocessing blocks that filter and condition the
raw sync information retrieved from the digitized analog video.
•
VSYNC Processor. This block provides extra filtering of the
detected VSYNCs to give improved vertical lock.
•
HSYNC Processor. The HSYNC processor is designed to
filter incoming HSYNCs that have been corrupted by
noise, providing much improved performance for video
signals with stable time base but poor SNR.
Table 30. VID_SEL Function
VID_SEL[3:0]
Address 0x00 [7:4]
Description
0000*
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
Autodetect (PAL BGHID) <–> NTSC J.
Autodetect (PAL BGHID) <–> NTSC M.
Autodetect (PAL N) <–> NTSC J.
Autodetect (PAL N) <–> NTSC M.
NTSC J (1)
NTSC M (1).
PAL 60.
NTSC 4.43 (1).
PAL BGHID.
PAL N ( = PAL BGHID (with pedestal)).
PAL M (without pedestal).
PAL M.
PAL combination N.
PAL combination N (with pedestal).
SECAM.
SDP VBI DATA RECOVERY
The SDP can retrieve the following information from the input
video:
•
•
•
•
•
•
Wide-screen signaling (WSS)
Copy generation management system (CGMS)
Closed caption (CC)
Macrovision protection presence
EDTV data
Gemstar compatible data slicing
1101
1110
1111
The SDP is also capable of automatically detecting the incoming
video standard with respect to
SECAM (with pedestal).
*Default value.
•
•
•
Color subcarrier frequency
Field rate
AD_SEC525_EN Enable Autodetection of SECAM 525 line
video (SDP), Address 0x07, [7]
Table 31. AD_SEC525_EN Function
Line rate
AD_SEC525_EN Description
0*
Disable the autodetection of a 525-line
system with a SECAM style, FM-modulated
color component.
and can configure itself to support PAL-BGHID, PAL-M/N,
PAL-combination N, NTSC-M, NTSC-J, SECAM 50 Hz/60 Hz,
NTSC4.43, and PAL60.
1
Enable the detection.
*Default value.
Rev. A | Page 22 of 104
ADV7189
AD_SECAM_EN Enable Autodetection of SECAM (SDP),
Address 0x07, [6]
AD_PAL_EN Enable Autodetection of PAL (SDP),
Address 0x07, [0]
Table 32. AD_SECAM_EN Function
Table 38. AD_PAL_EN Function
AD_SECAM_EN
Description
AD_PAL_EN
Description
0
1*
Disable the autodetection of SECAM.
Enable the detection.
0
1*
Disable the detection of standard PAL.
Enable the detection.
*Default value.
*Default value.
AD_N443_EN Enable Autodetection of NTSC 443 (SDP),
Address 0x07, [5]
Table 33. AD_N443_EN Function
SFL_INV Subcarrier Frequency Lock Inversion (SDP)
This bit controls the behavior of the PAL switch bit in the SFL
(GenLock Telegram) data stream. It was implemented to solve
some compatibility issues with video encoders. It solves two
problems:
AD_N443_EN Description
0
Disable the autodetection of NTSC style
systems with a 4.43 MHz color subcarrier.
1*
Enable the detection.
1. The PAL switch bit is only meaningful in PAL. Some
encoders (including Analog Devices encoders) also look at
the state of this bit in NTSC.
*Default value.
AD_P60_EN Enable Autodetection of PAL60 (SDP),
Address 0x07, [4]
Table 34. AD_P60_EN Function
2. There was a design change in Analog Devices encoders
from ADV717x to ADV719x. The older versions used the
SFL (GenLock Telegram) bit directly, while the later ones
invert the bit prior to using it. The reason for this is that the
inversion compensated for the 1-line delay of an SFL
(GenLock Telegram) transmission.
AD_P60_EN Description
0
Disable the autodetection of PAL systems with a
60 Hz field rate.
Enable the detection.
1*
*Default value.
As a result:
AD_PALN_EN Enable Autodetection of PAL N (SDP),
Address 0x07, [3]
Table 35. AD_PALN_EN Function
1. ADV717x encoders need the PAL switch bit in the SFL
(GenLock Telegram) to be 1 for NTSC to work.
AD_PALN_EN
Description
2. ADV7190/ADV7191/ADV7194 encoders need the PAL
switch bit in the SFL to be 0 to work in NTSC.
0
1*
Disable the detection of the PAL N standard.
Enable the detection.
*Default value.
If the state of the PAL switch bit is wrong, a 180°phase shift
occurs.
AD_PALM_EN Enable Autodetection of PAL M (SDP),
Address 0x07, [2]
Table 36. AD_PALM_EN Function
In a decoder/encoder back-to-back system in which SFL is used,
this bit must be set up properly for the specific encoder used.
AD_PALM_EN
Description
Table 39. SFL_INV Function
SFL_INV
Address 0x41, [6] Description
0
1*
Disable the autodetection of PAL M.
Enable the detection.
*Default value.
0
SFL compatible with ADV7190/ADV7191/
ADV7194 encoders.
AD_NTSC_EN Enable Autodetection of NTSC (SDP),
Address 0x07, [1]
Table 37. AD_NTSC_EN Function
1*
SFL compatible with ADV717x/ADV7173x
encoders.
*Default value.
AD_NTSC_EN Description
0
1*
Disable the detection of standard NTSC.
Enable the detection.
*Default value.
Rev. A | Page 23 of 104
ADV7189
Lock Related Controls (SDP)
CIL[2:0] Count Into Lock (SDP), Address 0x51, [2:0]
Lock information is presented to the user through Bits [1:0] of
the Status 1 register. See the STATUS_1[7:0] Address 0x10, [7:0]
section. Figure 9 outlines the signal flow and the controls
available to influence the way the lock status information is
generated.
CIL[2:0] determines the number of consecutive lines for which
the into lock condition must be true before the system switches
into the locked state, and reports this via Status 0 [1:0].
Table 42. CIL Function
CIL[2:0]
Description (Count Value in Lines of Video)
SRLS Select Raw Lock Signal (SDP), Address 0x51, [6]
000
1
001
010
011
100*
101
2
5
10
100
500
1000
100000
Using the SRLS bit, the user can choose between two sources for
determining the lock status (per Bits [1:0] in the Status 1
register).
•
The time_win signal is based on a line-to-line evaluation of
the horizontal synchronization pulse of the incoming
video. It reacts quite quickly.
110
111
*Default value.
•
The free_run signal evaluates the properties of the
incoming video over several fields, and takes vertical
synchronization information into account.
COL[2:0] Count Out of Lock (SDP), Address 0x51, [5:3]
COL[2:0] determines the number of consecutive lines for which
the out of lock condition must be true before the system
switches into unlocked state, and reports this via Status 0 [1:0].
Table 40. SRLS Function
SRLS
Description
0*
1
Select the free_run signal.
Select the time_win signal.
Table 43. COL Function
COL[2:0]
Description (Count Value in Lines of Video)
*Default value.
000
1
001
010
2
5
FSCLE Fsc Lock Enable (SDP), Address 0x51, [7]
The FSCLE bit allows the user to choose whether the status of
the color subcarrier loop is taken into account when the overall
lock status is determined and presented via Bits [1:0] in Status
Register 1. This bit must be set to 0 when operating the SDP in
YPrPb component mode in order to generate a reliable HLOCK
status bit.
011
100*
101
110
111
*Default value.
10
100
500
1000
100000
Table 41. FSCLE Function
FSCLE
Description
0
Overall lock status only dependent on horizontal
sync lock.
1*
Overall lock status dependent on horizontal sync
lock and Fsc Lock.
*Default value.
SELECT THE RAW LOCK SIGNAL
SRLS
FILTER THE RAW LOCK SIGNAL
CIL[2:0], COL[2:0]
TIME_WIN
1
0
0
1
FREE_RUN
COUNTER INTO LOCK
COUNTER OUT OF LOCK
STATUS 1 [0]
STATUS 1 [1]
F
LOCK
SC
MEMORY
TAKE F LOCK INTO ACCOUNT
SC
FSCLE
Figure 9. SDP Lock Related Signal Path
Rev. A | Page 24 of 104
ADV7189
SDP COLOR CONTROLS
The following registers provide user control over the picture
appearance including control of the active data in the event of
video being lost. They are independent of any other controls.
For instance, brightness control is independent from picture
clamping, although both controls affect the signal’s dc level.
SD_SAT_Cr[7:0] SD Saturation Cr Channel (SDP),
Address 0xE4, [7:0]
This register allows the user to control the gain of the Cr
channel only. This register affects the SDP core only.
For this register to be active , SAT[7:0] must be programmed
with its default value of 0x80. If SAT[7:0] is programmed with a
different value, SD_SAT_Cb[7:0] and SD_SAT_Cr[7:0] are
inactive.
CON[7:0] Contrast Adjust (SDP), Address 0x08, [7:0]
This is the user control for contrast adjustment for the SDP
block only.
Table 47. SD_SAT_Cr Function
Description
Table 44. CON Function
SD_SAT_Cr[7:0] (Adjust Saturation of the Picture)
CON[7:0]
Description (Adjust Contrast of the Picture)
0x±0*
0x00
0xFF
*Default value.
Chroma gain = 0 dB
0x±0*
Gain on luma channel = 1.
0x00
Gain on luma channel = 0.
0xFF
Gain on luma channel = 2.
*Default value.
SD_OFF_Cb[7:0] SD Offset Cb Channel (SDP),
Address 0xE1, [7:0]
SAT[7:0] Saturation Adjust (SDP), Address 0x09, [7:0]
The user can adjust the saturation of the color output using this
register. This registers affects the SDP core only.
This register allows the user to select an offset for the Cb
channel only. This register affects the SDP core only. There is a
functional overlap with the Hue [7:0] register.
ADI encourages users not to use the SAT[7:0] register, which
may be removed in future revisions of the ADV7189. Instead,
the SD_SAT_U and SD_SAT_V registers should be used.
Table 48. SD_OFF_Cb Function
Description
(Adjust Hue of the Picture by Selecting an
SD_OFF_Cb[7:0] Offset for Data on the V Channel)
Table 45. SAT Function
SAT[7:0] Description (Adjust Saturation of the Picture)
0x±0*
0x7F
0xFF
*Default value.
0x±0*
0x00
0xFF
Chroma gain = 0 dB.
Chroma gain = –42 dB.
Chroma gain = 6 dB.
*Default value.
SD_OFF_Cr [7:0] SD Offset Cr Channel (SDP),
Address 0xE2, [7:0]
SD_SAT_Cb[7:0] SD Saturation Cb Channel (SDP),
Address 0xE3, [7:0]
This register allows the user to select an offset for the Cr
channel only. This register affects the SDP core only. There is a
functional overlap with the Hue [7:0] register.
This register allows the user to control the gain of the Cb
channel only.
For this register to be active , SAT[7:0] must be programmed
with its default value of 0x80. If SAT[7:0] is programmed with a
different value, SD_SAT_Cb[7:0] and SD_SAT_Cr[7:0] are
inactive.
Table 49. SD_OFF_Cr Function
Description (Adjust Hue of the Picture by
SD_OFF_Cr[7:0] Selecting an Offset for Data on V Channel)
0x±0*
0x7F
Table 46. SD_SAT_Cb Function
0xFF
Description
SD_SAT_Cb[7:0] (Adjust Saturation of the Picture)
*Default value.
0x±0*
Chroma gain = 0 dB.
0x00
0xFF
*Default value.
Rev. A | Page 25 of 104
ADV7189
BRI[7:0] Brightness Adjust (SDP), Address 0x0A, [7:0]
Table 52. DEF_Y Function
DEF_Y[5:0]
Description
This register controls the brightness of the video signal through
the SDP core.
0x36 (Blue)*
*Default value.
Default value of Y.
Table 50. BRI Function
BRI[7:0]
Description (Adjust Brightness of the Picture)
DEF_C[7:0] Default Value C (SDP), Address 0x0D, [7:0]
0x00*
0x7F
0xFF
Offset of the luma channel = 0IRE.
Offset of the luma channel = 100IRE.
Offset of the luma channel = –100IRE.
The DEF_C[7:0] register complements the DEF_Y[5:0] value. It
defines the 4 MSBs of Cr and Cb values to be output if
*Default value.
•
The DEF_VAL_AUTO_EN bit is set to high and the
ADV7189 can’t lock to the input video (automatic mode).
HUE[7:0] Hue Adjust (SDP), Address 0x0B, [7:0]
•
DEF_VAL_EN bit is set to high (forced output).
This register contains the value for the color hue adjustment.
The data that is finally output from the ADV7189 for the
chroma side is Cr[7:0] = {DEF_C[7:4], 0, 0, 0, 0}, Cb[7:0] =
{DEF_C[3:0], 0, 0, 0, 0}.
HUE[7:0] has a range of 90°, with 0x00 equivalent to an
adjustment of 0°. The resolution of HUE[7:0] is 1 bit = 0.7°.
The hue adjustment value is fed into the AM color
demodulation block. Therefore, it only applies to video signals
that contain chroma information in the form of an AM
modulated carrier (CVBS or Y/C in PAL or NTSC). It does not
affect SECAM and does not work on component video inputs
(YPrPb).
In cases of full 10-bit output mode, two extra LSBs of value 00
are appended.
Table 53. DEF_C Function
DEF_C[7:0]
0x7C (blue)*
*Default value.
Description
Default values for Cr and Cb.
Table 51. HUE Function
HUE[7:0]
Description (Adjust Hue of the Picture)
DEF_VAL_EN Default Value Enable (SDP),
Address 0x0C, [0]
0x00*
0x7F
0xFF
*Default value.
Phase of the chroma signal = 0°.
Phase of the chroma signal = –90°.
Phase of the chroma signal = +90°.
This bit forces the use of the default values for Y, Cr, and Cb.
Refer to the descriptions for DEF_Y and DEF_C for additional
information. The decoder also outputs a stable 27 MHz clock,
HS, and VS in this mode.
DEF_Y[5:0] Default Value Y (SDP), Address 0x0C, [7:2]
In cases where the ADV7189 loses lock on the incoming video
signal or where there is no input signal, the DEF_Y[5:0] register
allows the user to specify a default luma value to be output.
Table 54. DEF_VAL_EN Function
DEF_VAL_EN Description
0*
Don't force the use of default Y, Cr, and Cb
values. Output colors dependent on
DEF_VAL_AUTO_EN.
This value is used under the following conditions:
1
Always use default Y, Cr, and Cb values.
Override picture data even if the video decoder
is locked.
•
If DEF_VAL_AUTO_EN bit is set to high and the
ADV7189 lost lock to the input video signal. This is the
intended mode of operation (automatic mode).
*Default value.
•
•
The DEF_VAL_EN bit is set, regardless of the lock status of
the video decoder.
DEF_VAL_AUTO_EN Default Value Automatic Enable
(SDP), Address 0x0C, [1]
This bit enables the automatic usage of the default values for Y,
Cr, and Cb in cases where the ADV7189 cannot lock to the
video signal.
This is a forced mode that may be useful during
configuration.
The DEF_Y[5:0] values define the 6 MSBs of the output video.
The remaining LSBs are padded with 0s. (For example, in 10-bit
mode, the output is Y[9:0] = {DEF_Y[5:0], 0, 0, 0, 0}.)
Table 55. DEF_VAL_AUTO_EN Function
DEF_VAL_AUTO_EN Description
0
Don't use default Y, Cr, and Cb values. If
unlocked, output noise.
1*
Use default Y, Cr, and Cb values when
decoder loses lock.
*Default value.
Rev. A | Page 26 of 104
ADV7189
SDP CLAMP OPERATION
FINE
CURRENT
SOURCES
COARSE
CURRENT
SOURCES
DATA
PRE
PROCESSOR
(DPP)
ANALOG
VIDEO
INPUT
SDP
WITH DIGITAL
FINE CLAMP
ADC
CLAMP CONTROL
Figure 10. SDP Clamping Overview
The input video is ac-coupled into the ADV7189. Therefore its
dc value needs to be restored. This process is referred to as
clamping the video. This section explains the general process of
clamping on the ADV7189 for the SDP and shows the different
ways in which a user can configure its behavior.
The clamping scheme has to complete two tasks: it must be able
to acquire a newly connected video signal with a completely
unknown dc level, and it must maintain the dc level during
normal operation.
For a fast acquiring of an unknown video signal, the large
current clamps may be activated7. Control of the coarse and fine
current clamp parameters is performed automatically by the
decoder.
The SDP block uses a combination of current sources and a
digital processing block for clamping, as shown in Figure 10.
The analog processing channel shown is replicated three times
inside the IC. While only one single channel (and only one
ADC) would be needed for a CVBS signal, two independent
channels are needed for YC (S-VHS) type signals, and three
independent channels are needed to allow component signals
(YPrPb) to be processed.
Standard definition video signals may have excessive noise on
them. In particular, CVBS signals transmitted by terrestrial
broadcast and demodulated using a tuner usually show very
large levels of noise (>100 mV). A voltage clamp would be
unsuitable for this type of video signal. Instead, the ADV7189
employs a set of four current sources that can cause coarse
(>0.5 mA) and fine (<0.1 mA) currents to flow into and away
from the high impedance node that carries the video signal (see
Figure 10).
The clamping can be divided into two sections:
•
Clamping before the ADC (analog domain): current
sources.
The following sections describe the I2C signals that can be used
to influence the behavior of SDP clamping.
•
Clamping after the ADC (digital domain): digital
processing block.
The ADCs can digitize an input signal only if it resides within
the ADC’s 1.6 V input voltage range. An input signal with a dc
level that is too large or too small is clipped at the top or bottom
of the ADC range.
Previous revisions of the ADV7189 had controls (FACL/FICL,
fast and fine clamp length) to allow configuration of the length
for which the coarse (fast) and fine current sources are switched
on. These controls were removed on the ADV7189-FT and
replaced by an adaptive scheme.
The primary task of the analog clamping circuits is to ensure
that the video signal stays within the valid ADC input window
so the analog to digital conversion can take place. It is not nec-
essary to clamp the input signal with a very high accuracy in the
analog domain as long as the video signal fits the ADC range.
CCLEN Current Clamp Enable (SDP), Address 0x14, [4]
The current clamp enable bit allows the user to switch off the
current sources in the analog front end altogether. This may be
useful if the incoming analog video signal is clamped externally.
After digitization, the digital fine clamp block corrects for any
remaining variations in dc level. Since the dc level of an input
video signal refers directly to the brightness of the picture
transmitted, it is important to perform a fine clamp with high
accuracy; otherwise, brightness variations may occur.
Furthermore, dynamic changes in the dc level will almost
certainly lead to visually objectionable artifacts, and must
therefore be prohibited.
Table 56. CCLEN Function
CCLEN
Description
0
1*
Current sources switched off.
Current sources enabled.
*Default value.
7 It is assumed that the amplitude of the video signal at this point is of a
nominal value.
Rev. A | Page 27 of 104
ADV7189
DCT[1:0] Digital Clamp Timing (SDP), Address 0x15, [6:5]
frequency noise, reducing the bandwidth of the luma signal
improves visual picture quality. A follow-on video com-
pression stage may work more efficiently if the video is
low-pass filtered.
The Clamp Timing register determines the time constant of the
digital fine clamp circuitry. It is important to realize that the
digital fine clamp reacts very fast since it is supposed to
immediately correct any residual dc level error for the active
line. The time constant of the digital fine clamp must be much
quicker than the one from the analog blocks.
The ADV7189 allows selection of two responses for the
shaping filter: one that is used for good quality CVBS,
component, and S-VHS type sources, and a second for
nonstandard CVBS signals.
By default, the time constant of the digital fine clamp is adjusted
dynamically to suit the currently connected input signal.
The YSH filter responses also include a set of notches for
PAL and NTSC. However, it is recommended to use the
comb filters for YC separation.
Table 57. DCT Function
DCT[1:0] Description
00
01
10*
11
Slow (TC = 1 sec).
Medium (TC = 0.5 sec).
Fast (TC = 0.1 sec).
Determined by ADV71±9 dependent on video
parameters.
•
Luma peaking filter. This filter can be manually enabled.
The user can select to boost or attenuate the midregion of
the Y spectrum around 3 MHz. The peaking filter may
visually improve the picture by showing more definition on
those picture details that contain frequency components
around 3 MHz. The peaking filter compensates for the
effects of a wide notch filter: Where the notch starts to fall
off, the peaking filter lifts the overall response back on.
*Default value.
DCFE Digital Clamp Freeze Enable (SDP), Address 0x15, [4]
This register bit allows the user to freeze the digital clamp loop
at any time. It is intended for users who would like to do their
own clamping. Users should disable the current sources for
analog clamping via the appropriate register bits, wait until the
digital clamp loop settles, and then freeze it via the DCFE bit.
•
Digital resampling filter. This block is used to allow
dynamic resampling of the video signal to alter parameters
such as the time base of a line of video. Fundamentally, the
resampler is a set of low-pass filters. The actual response is
chosen by the system with no requirement for user
intervention.
Table 58.
DCFE
Description
0*
1
Digital clamp operational.
Digital clamp loop frozen.
Figure 12 through Figure 15 show the overall response of all
filters together. Unless otherwise noted, the filters are set into a
typical wideband mode, and the peaking function is disabled.
*Default value.
SDP LUMA FILTER
Data8 from the digital fine clamp block is processed by four sets
of filters:
Y Shaping Filter
For input signals in CVBS format, the luma shaping filters play
an essential role in removing the chroma component from a
composite signal. YC separation must aim for best possible
crosstalk reduction while still retaining as much bandwidth
(especially on the luma component) as possible. High quality
YC separation can be achieved by using the internal comb filters
of the ADV7189. Comb filtering, however, relies on the
frequency relationship of the luma component (multiples of the
video line rate) and the color subcarrier (Fsc). For good quality
CVBS signals, this relationship is known; the comb filter
algorithms can be used to separate out luma and chroma with
high accuracy.
•
Luma antialias filter (YAA). The SDP received video at a
rate of 27 MHz9. The ITU-R BT.601 recommends a
sampling frequency of 13.5 MHz. The luma antialias filter
decimates the oversampled video using a high quality,
linear phase, low-pass filter that preserves the luma signal
while at the same time attenuating out-of-band
components. The luma antialias filter (YAA) has a fixed
response.
•
Luma shaping filters (YSH). The shaping filter block is a
programmable low-pass filter with a wide variety of
responses. It can be used to selectively reduce the luma
video signal bandwidth (needed prior to scaling, for
example). For some video sources that contain high
In the case of nonstandard video signals, the frequency
relationship may be disturbed and the comb filters may not be
able to remove all crosstalk artifacts in an optimum fashion
without the assistance of the shaping filter block.
± The data format at this point is CVBS for CVBS input or luma only for Y/C and
YPrPb input formats.
9 In the case of 4× oversampled video, the ADCs sample at 54 MHz, and the
first decimation is performed inside the DPP filters. Therefore, the data rate
into the SDP core is always 27 MHz.
Rev. A | Page 2± of 104
ADV7189
An automatic mode is provided. Here, the ADV7189 evaluates
the quality of the incoming video signal and selects the filter
responses in accordance with the signal quality and video
standard. YFSM, WYSFMOVR, and WYSFM allow the user to
manually override the automatic decisions in part or in full.
YSFM[4:0] Y Shaping Filter Mode (SDP), Address 0x17, [4:0]
The Y shaping filter mode bits allow the user to select from a
wide range of low-pass and notch filters. When switched in
automatic mode, the filter is selected based on other register
selections (e.g., detected video standard) as well as properties
extracted from the incoming video itself (e.g., quality, time base
stability). The automatic selection always picks the widest
possible bandwidth for the video input encountered.
The luma shaping filter has three control registers:
•
YSFM[4:0] allows the user to manually select a shaping
filter mode (applied to all video signals) or to enable an
automatic selection (dependent on video quality and video
standard).
•
If the YSFM settings specify a filter (i.e., YSFM is set to
values other than 00000 or 00001), the chosen filter is
applied to all video, regardless of its quality.
•
•
WYSFMOVR allows the user to manually override the
WYSFM decision.
•
In automatic selection mode, the notch filters are only used
for bad quality video signals. For all other video signals,
wide band filters are used.
WYSFM[4:0] allows the user to select a different shaping
filter mode for good quality CVBS, component (YPrPb),
and S-VHS (YC) input signals.
WYSFMOVR Wideband Y Shaping Filter Override (SDP),
Address 0x18,[7]
In automatic mode, the system preserves the maximum possible
bandwidth for good CVBS sources (since they can successfully
be combed) as well as for luma components of YPrPb and YC
sources, since they need not be combed. For poor quality
signals, the system selects from a set of proprietary shaping
filter responses that complements comb filter operation in order
to reduce visual artifacts.
Setting the WYSFMOVR bit enables the use of the WYSFM[4:0]
settings for good quality video signals. For more information,
refer to the general discussion of the luma shaping filters in the
Y Shaping Filter section and the flowchart shown in Figure 11.
Table 59.
WYSFMOVR Description
0
Automatic selection of shaping filter for good
quality video signals.
The decisions of the control logic are shown in Figure 11.
1*
Enable manual override via WYSFM[4:0].
*Default value.
SET YSFM
YSFM IN AUTO MODE?
00000 OR 00001
YES
NO
VIDEO
QUALITY
BAD
GOOD
USE YSFM SELECTED
FILTER REGARDLESS FOR
GOOD AND BAD VIDEO
AUTO SELECT LUMA
SHAPING FILTER TO
COMPLEMENT COMB
WYSFMOVR
1
0
SELECT WIDEBAND
FILTER AS PER
WYSFM[4:0]
SELECT AUTOMATIC
WIDEBAND FILTER
Figure 11. YSFM and WYSFM Control Flowchart
Rev. A | Page 29 of 104
ADV7189
Table 60. YSFM Function
Table 61. WYSFM Function
YSFM[4:0] Description
WYSFM[4:0]
Description
Do not use
Do not use
SVHS 1
SVHS 2
SVHS 3
SVHS 4
SVHS 5
SVHS 6
SVHS 7
0'0000
Automatic selection including a wide notch
0'0000
0'0001
response (PAL/NTSC/SECAM)
0'0001*
Automatic selection including a narrow notch
response (PAL/NTSC/SECAM)
0'0010
0'0011
0'0100
0'0101
0'0110
0'0111
0'1000
0'1001
0'1010
0'1011
0'1100
0'1101
0'1110
0'1111
1'0000
1'0001
1'0010
0'0010
0'0011
0'0100
0'0101
0'0110
0'0111
0'1000
0'1001
0'1010
0'1011
0'1100
0'1101
0'1110
0'1111
1'0000
1'0001
1'0010
1'0011
1'0100
1'0101
1'0110
1'0111
1'1000
1'1001
1'1010
1'1011
1'1100
1'1101
1'1110
1'1111
*Default value.
SVHS 1
SVHS 2
SVHS 3
SVHS 4
SVHS 5
SVHS 6
SVHS 7
SVHS ±
SVHS ±
SVHS 9
SVHS 10
SVHS 11
SVHS 12
SVHS 13
SVHS 14
SVHS 15
SVHS 16
SVHS 17
SVHS 1± (CCIR 601)
Do not use
SVHS 9
SVHS 10
SVHS 11
SVHS 12
SVHS 13
SVHS 14
SVHS 15
SVHS 16
SVHS 17
SVHS 1± (CCIR 601)
PAL NN 1
PAL NN 2
PAL NN 3
PAL WN 1
PAL WN 2
NTSC NN 1
NTSC NN 2
NTSC NN 3
NTSC WN 1
NTSC WN 2
NTSC WN 3
Reserved
1'0011*
1'0100–1’1111
*Default value.
v740a COMBINED Y ANTIALIAS, S-VHS LOW-PASS FILTERS,
Y RESAMPLE
0
–10
–20
–30
–40
–50
–60
–70
0
2
4
6
8
10
12
WYSFM[4:0] Wide Band Y Shaping Filter Mode (SDP),
Address 0x18, [4:0]
FREQUENCY (MHz)
Figure 12. SDP Y S-VHS Combined Responses
The WYSFM[4:0] bits allow the user to manually select a
shaping filter for good quality video signals (e.g., CVBS with
stable time base, luma component of YPrPb, luma component
of YC). The WYSFM bits are only active if the WYSFMOVR bit
is set to 1. See the general discussion of the shaping filter
settings in the Y Shaping Filter section.
The filter plots in Figure 12 show the S-VHS 1 (narrowest) to
S-VHS 18 (widest) shaping filter settings. Figure 14 shows the
PAL notch filter responses. The NTSC compatible notches are
shown in Figure 15.
Rev. A | Page 30 of 104
ADV7189
v740a COMBINED Y ANTIALIAS, CCIR MODE SHAPING FILTER,
Y RESAMPLE
YPM[2:0] Y Peaking Filter Mode (SDP), Address 0x02, [2:0]
0
–20
Allows the user to select peaking. This function allows the user
to boost/attenuate luma signals around the color subcarrier
frequency. Selecting YPM = 000,001,010,011 sharpens the
image; YPM = 101,110,111 attenuates the luma around the color
subcarrier. In cases of incomplete cancellation in the Y comb
filter, this could be used to attenuate any residual C components
(hanging dots) in the Y output at the cost of a softer image.
–40
–60
–80
Table 62. YPM Function
Filter Response (Peak Position)
–100
–120
YPM[2:0]
000
001
010
011
Composite (2.6 MHz)
+4.5 dB
S-VHS (3.75 MHz)
+9.25 dB
+9.25 dB
+5.75 dB
+3.3 dB
0
2
4
6
8
10
12
+4.5 dB
+4.5 dB
FREQUENCY (MHz)
Figure 13. SDP Y S-VHS 18 Extra Wideband Filter (CCIR 601 Compliant)
+1.25 dB
0
100*
0
v740a COMBINED Y ANTIALIAS, PAL NOTCH FILTERS,
Y RESAMPLE
101
110
111
*Default value.
–1.25 dB
–1.75 dB
–3.0 dB
–3.0 dB
–±.0 dB
–±.0 dB
0
–10
–20
–30
–40
–50
–60
–70
SDP CHROMA FILTER
Data10 from the digital fine clamp block is processed by two sets
of filters:
•
•
•
Chroma Antialias Filter (CAA). The ADV7189
oversamples the CVBS by a factor of 2 and the
Chroma/UV by a factor of 4. A decimating filter (CAA) is
used to preserve the active video band and remove any out-
of-band components. The CAA filter has a fixed response.
0
2
4
6
8
10
12
FREQUENCY (MHz)
Chroma Shaping Filters (CSH). The shaping filter block
(CSH) can be programmed to perform a variety of low-
pass responses. It can be used to selectively reduce the
bandwidth of the chroma signal for scaling or
compression.
Figure 14. SDP Y S-VHS 18 Extra Wideband Filter (CCIR 601 Compliant)
v740a COMBINED Y ANTIALIAS, NTSC NOTCH FILTERS,
Y RESAMPLE
0
–10
–20
–30
–40
–50
–60
–70
Digital Resampling Filter. This block is used to allow
dynamic resampling of the video signal to alter parameters
such as the time base of a line of video. Fundamentally, the
resampler is a set of low-pass filters. The actual response is
chosen by the system with no requirement for user
intervention.
The plots in Figure 16 show the overall response of all filters
together.
0
2
4
6
8
10
12
FREQUENCY (MHz)
Figure 15. SDP Y S-VHS 18 Extra Wideband Filter (601)
10 The data format at this point is CVBS for CVBS inputs, or chroma only for Y/C
or Cr/Cb interleaved for YCrCb input formats.
Rev. A | Page 31 of 104
ADV7189
CSFM[2:0] C Shaping Filter Mode (SDP), Address 0x17, [7]
SDP GAIN OPERATION
The C shaping filter mode bits allow the user to select from a
range of low-pass filters for the chrominance signal. When
switched in automatic mode, the widest filter is selected based
on the video standard/format and user choice (see settings 000
and 001 in Table 63).
The gain control within the ADV7189 is done on a purely
digital basis. The input ADCs support a 12-bit range, mapped
into a 1.6 V analog voltage range. Gain correction takes place
after the digitization in the form of a digital multiplier.
There are several advantages of this architecture over the
commonly used PGA (programmable gain amplifier) before the
ADCs; among them is the fact that the gain is now completely
independent of supply, temperature, and process variations.
Table 63. CSFM Function
CSFM[2:0]
Description
000*
Autoselect 1.5 MHz bandwidth
001
Autoselect 2.17 MHz bandwidth
As shown in Figure 17, the ADV7189 can decode a video signal
as long as it fits into the ADC window. There are two compo-
nents to this: the amplitude of the input signal and the dc level it
resides on. The dc level is set by the clamping circuitry (see the
SDP Clamp Operation section).
010
011
100
101
SH1
SH2
SH3
SH4
110
SH5
111
*Default value.
Wideband Mode
If the amplitude of the analog video signal is too high, clipping
may occur, resulting in visual artifacts. The analog input range
of the ADC, together with the clamp level, determines the
maximum supported amplitude of the video signal.
v740a COMBINED C ANTIALIAS, C SHAPING FILTER,
C RESAMPLER
0
–10
–20
–30
–40
–50
The minimum supported amplitude of the input video is
determined by the SDP core’s ability to retrieve horizontal and
vertical timing and to lock to the colorburst (if present).
There are two gain control units, one each for luma and chroma
data. Both can operate independently of each other. The chroma
unit, however, can also take its gain value from the luma path.
Several AGC modes are possible; Table 64 summarizes them.
It is possible to freeze the automatic gain control loops. This will
cause the loops to stop updating and the AGC determined gain
at the time of the freeze stays active until the loop is either
unfrozen or the gain mode of operation is changed.
–60
0
1
2
3
4
5
6
FREQUENCY (MHz)
Figure 16. SDP Chroma Shaping Filter Responses
Figure 16 shows the responses of SH1 (narrowest) to SH5
(widest) in addition to the wideband mode (in red).
The currently active gain from any of the modes can be read
back. Please refer to the description of the dual function manual
gain registers, LG[11:0] Luma Gain and CG[11:0] Chroma
Gain, in the SDP Luma Gain and SDP Chroma Gain sections.
ANALOG VOLTAGE
RANGE SUPPORTED BY ADC (1.6V RANGE FOR ADV7189)
MAXIMUM
VOLTAGE
SDP
(GAIN SELECTION ONLY)
DATA
PRE
ADC
PROCESSOR
(DPP)
GAIN
CONTROL
MINIMUM
VOLTAGE
CLAMP
LEVEL
Figure 17. SDP Gain Control Overview
Rev. A | Page 32 of 104
ADV7189
Table 64. SDP AGC Modes
Input Video Type
Luma Gain
Chroma Gain
Any
Manual gain luma.
Manual gain chroma.
CVBS
Dependent on horizontal sync depth.
Dependent on color burst amplitude.
Taken from luma path.
Peak White
Dependent on color burst amplitude.
Taken from luma path.
Y/C
Dependent on horizontal sync depth.
Peak White.
Dependent on color burst amplitude.
Taken from luma path.
Dependent on color burst amplitude.
Taken from luma path.
YPrPb
Dependent on horizontal sync depth.
Taken from luma path.
SDP Luma Gain
Table 66. LAGT Function
LAGT[1:0]
Description
LAGC[2:0] Luma Automatic Gain Control (SDP), Address
0x30, [7:0]
00
01
10
11*
Slow (TC = 2 sec)
Medium (TC = 1 sec)
Fast (TC = 0.2 sec)
Adaptive
The luma automatic gain control mode bits select the mode of
operation for the gain control in the luma path.
*Default value.
There are ADI internal parameters to customize the peak white
gain control. Contact ADI for more information.
LG[11:0] Luma Gain (SDP), Address 0x2F, [3:0];
Address 0x30, [7:0]; LMG[11:0] Luma Manual Gain (SDP),
Address 0x2F, [3:0]; Address 0x30, [7:0]
Table 65. LAGC Function
LAGC[2:0] Description
Luma gain [11:0] is a dual function register:
000
001
Manual fixed gain (use LMG[11:0]).
AGC (blank level to sync tip). No override through
white peak.
AGC (blank level to sync tip). Automatic override
through white peak.
Reserved
Reserved.
Reserved.
Reserved.
Freeze gain.
•
•
If written to, a desired manual luma gain can be
programmed. This gain becomes active if the LAGC[2:0]
mode is switched to manual fixed gain.
010*
011
100
101
110
111
*Default value.
Equation 1 shows how to calculate a desired gain.
If read back, this register returns the current gain value.
Depending on the setting in the ALCM[2:0] bits, this is one
of the following values:
o
o
Luma manual gain value (ALCM[2:0] set to luma
manual gain mode)
LAGT[1:0] Luma Automatic Gain Timing (SDP),
Address 0x2F, [7:6]
Luma automatic gain value (ALCM[2:0] set to any of the
automatic modes)
The luma automatic gain timing register allows the user to
influence the tracking speed of the luminance automatic gain
control. Please note that this register only has an effect if the
LAGC[2:0] register is set to 001, 010, 011, or 100 (automatic
gain control modes).
Table 67. LG/LMG Function
LG[11:0]/LMG[11:0] Read/Write Description
LMG[11:0] = X
Write
Manual gain for luma
path.
If peak white AGC is enabled and active (see the
LG[11:0]
Read
Actually used gain.
STATUS_1[7:0] Address 0x10, [7:0] section), the actual gain
update speed is dictated by the peak white AGC loop and, as a
result, the LAGT settings have no effect. As soon as the part
leaves peak white AGC, LAGT becomes relevant again.
(
0 < LG ≤ 4095
)
Luma _ Gain =
= 0...2
2048
Equation 1. SDP Luma Gain Formula
The update speed for the peak white algorithm can be
customized by the use of internal parameters. Please contact
ADI for more information.
Rev. A | Page 33 of 104
ADV7189
Example
PW_UPD Peak White Update (SDP), Address 0x2B, [0]
Program the ADV7189 into manual fixed gain mode with a
desired gain of 0.89:
The peak white and average video algorithms determine the
gain based on measurements taken from the active video. The
PW_UPD bit determines the rate of gain change. Please note
that the LAGC[2:0] must be set to the appropriate mode to
enable the peak white or average video mode in the first place.
For more information, refer to the LAGC[2:0] Luma Automatic
Gain Control (SDP), Address 0x30, [7:0] section.
•
•
•
•
Use Equation 1 to convert the gain:
0.89 × 2048 = 1822.72
Truncate to integer value:
1822.72 = 1822
Table 69. PW_UPD Function
Convert to hexadecimal:
1822d = 0x71E
PW_UPD
Description
0
1
Update gain once per video line.
Update gain once per field.
Split into two registers and program:
Luma Gain Control 1 [3:0] = 0x7
Luma Gain Control 2 [7:0] = 0x1E
*Default value.
SDP Chroma Gain
•
Enable Manual Fixed Gain Mode:
Set LAGC[2:0] to 000
CAGC[1:0] Chroma Automatic Gain Control (SDP),
Address 0x2C, [1:0]
The two bits of Color Automatic Gain Control mode select the
basic mode of operation for automatic gain control in the
chroma path.
BETACAM Enable Betacam Levels (SDP), Address 0x01, [5]
If YPrPb data is routed through the SDP core, the automatic
gain control modes can target different video input levels, as
outlined in Table 72. Please note that the BETACAM bit is valid
only if the input mode is YPrPb (component) and if the data is
routed through the SDP core. The BETACAM bit basically sets
the target value for AGC operation.
Table 70. CAGC Function
CAGC[1:0]
Description
00
01
10*
11
Manual fixed gain (use CMG[11:0]).
Use luma gain for chroma.
Automatic gain (based on color burst).
Freeze chroma gain.
A review of the following sections is useful:
*Default value.
•
•
INSEL[3:0] Input Selection, Address 0x00, [3:0] to find out
how component video (YPrPb) can be routed through the
SDP core.
CAGT[1:0] Chroma Automatic Gain Timing (SDP),
Address 0x2D, [7:6]
The Chroma Automatic Gain Timing register allows the user to
influence the tracking speed of the chroma automatic gain
control. This register only has an effect if the CAGC[1:0]
register is set to 10 (automatic gain).
Video Standard Selection (SDP) to select the various
standards (e.g., with and without pedestal)
The automatic gain control (AGC) algorithms adjust the levels
based on the setting of the BETACAM bit(see Table 68.).
Table 71. CAGT Function
CAGT[1:0]
Description
Table 68. BETACAM Function
00
01
10
11*
Slow (TC = 2 sec)
Medium (TC = 1 sec)
Fast (TC = 0.2 sec)
Adaptive
BETACAM Description
0*
Assuming YPrPb is selected as input format.
Selecting PAL with pedestal selects MII.
Selecting PAL without pedestal selects SMPTE.
Selecting NTSC with pedestal selects MII.
Selecting NTSC without pedestal selects SMPTE.
Assuming YPrPb is selected as input format.
Selecting PAL with pedestal selects BETACAM.
*Default value.
1
Selecting PAL without pedestal selects BETACAM
variant.
Selecting NTSC with pedestal selects BETACAM.
Selecting NTSC without pedestal selects BETACAM
variant.
*Default value.
Rev. A | Page 34 of 104
ADV7189
Table 72. Betacam Levels
Name
Betacam (mV)
Betacam Variant (mV)
0 to 714
SMPTE (mV)
0 to 700
MII (mV)
Y Range
0 to 714 (incl. 7.5% pedestal)
0 to 700 (incl. 7.5% pedestal)
U and V Range
Sync Depth
–467 to +467
2±6
–505 to +505
2±6
–350 to +350
300
–324 to +324
300
For QAM based video standards (PAL and NTSC) as well as FM
based systems (SECAM), the threshold for the color kill
decision is selectable via the CKILLTHR[2:0] bits.
CG[11:0] Chroma Gain (SDP), Address 0x2D, [3:0];
Address 0x2E, [7:0] CMG[11:0] Chroma Manual Gain (SDP),
Address 0x2D, [3:0]; Address 0x2E, [7:0]
If color kill is enabled, and if the color carrier of the incoming
video signal is less than the threshold for 128 consecutive video
lines, color processing is switched off (black and white output).
To switch the color processing back on, another 128 consecutive
lines with a color burst greater than the threshold are required.
Chroma gain [11:0] is a dual function register:
•
If written to, a desired manual chroma gain can be
programmed. This gain becomes active if the CAGC[1:0]
mode is switched to manual fixed gain.
•
•
Refer to Equation 2 for calculating a desired gain.
The color kill option only works for input signals with a
modulated chroma part. For component input (YPrPb), there is
no color kill.
If read back, this register returns the current gain value.
Depending on the setting in the CAGC[1:0] bits, this will
be one of the following values:
Table 74. CKE Function
CKE
Description
o
o
Chroma manual gain value (CAGC[1:0] set to chroma
manual gain mode)
0
1*
Color kill disabled.
Color kill enabled.
*Default value.
Chroma automatic gain value (CAGC[1:0] set to any of
the automatic modes)
CKILLTHR[2:0] Color Kill Threshold (SDP),
Address 0x3D, [6:4]
Table 73. CG/CMG Function
CG[11:0]/CMG[11:0] Read/Write Description
The CKILLTHR[2:0] bits allow the user to select a threshold for
the color kill function. The threshold only applies to QAM
based (NTSC and PAL) or FM modulated (SECAM) video
standards.
CMG[11:0]
Write
Manual gain for chroma
path.
CG[11:0]
Read
Currently active gain.
To enable the color kill function, the CKE bit must be set. For
settings 000, 001, 010, and 011, chroma demodulation inside the
ADV7189 may not work satisfactorily for poor input video
signals.
(
0 < CG ≤ 4095
)
Chroma _ Gain =
= 0...4
1024
Equation 2. SDP Chroma Gain Formula
Table 75. CKILLTHR Function
Example
Description
Freezing the automatic gain loop and reading back the
CG[11:0] register results in a value of
CKILLTHR[2:0] SECAM
NTSC, PAL
000
001
010
011
100*
101
110
111
No color kill
Kill at < 0.5%
Kill at < 1.5%
Kill at < 2.5%
Kill at < 4.0%
Kill at < ±.5%
Kill at < 16.0%
Kill at < 32.0%
Kill at < 5%
Kill at < 7%
Kill at < ±%
Kill at < 9.5%
Kill at < 15%
Kill at < 32%
•
Convert the read back value to decimal:
0x47A = 1146d
•
Apply Equation 2 to convert the readback value:
1146/1024 = 1.12
Reserved for ADI internal use only. Do not
select.
CKE Color Kill Enable (SDP), Address 0x2B, [6]
The Color Kill Enable bit allows the optional color kill function
to be switched on or off.
*Default value.
Rev. A | Page 35 of 104
ADV7189
SDP CHROMA TRANSIENT IMPROVEMENT (CTI)
The signal bandwidth allocated for chroma is typically much
smaller than that of luminance. In the past, this was a valid way
to fit a color video signal into a given overall bandwidth because
the human eye is less sensitive to chrominance than to
luminance.
CTI_AB_EN Chroma Transient Improvement Alpha Blend
Enable (SDP), Address 0x4D, [1]
The CTI_AB_EN bit enables an alpha-blend function within
the CTI block. If set to 1, the alpha blender mixes the transient
improved chroma with the original signal. The sharpness of the
alpha blending can be configured via the CTI_AB[1:0] bits.
The uneven bandwidth, however, may lead to some visual
artifact when it comes to sharp color transitions. At the border
of two bars of color, both components (luma and chroma)
change at the same time (see Figure 18). Due to the higher
bandwidth, the signal transition of the luma component is
usually a lot sharper than that of the chroma component. The
color edge is not sharp but is blurred, in the worst case, over
several pixels.
For the alpha blender to be active, the CTI block must be
enabled via the CTI_EN bit.
Table 77. CTI_AB_EN
CTI_AB_EN
Description
0
1*
Disable CTI alpha blender.
Enable CTI alpha-blend mixing function.
*Default value.
LUMA SIGNAL WITH A
CTI_AB[1:0] Chroma Transient Improvement Alpha Blend
(SDP), Address 0x4D, [3:2]
TRANSITION, ACCOMPANIED
LUMA
SIGNAL
BY A CHROMA TRANSITION
The CTI_AB[1:0] controls the behavior of alpha-blend circuitry
that mixes the sharpened chroma signal with the original one. It
thereby controls the visual impact of CTI on the output data.
ORIGINAL, "SLOW" CHROMA
DEMODULATED
TRANSITION PRIOR TO CTI
CHROMA
SHARPENED CHROMA
SIGNAL
For CTI_AB[1:0] to become effective, the CTI block must be
enabled via the CTI_EN bit, and the alpha blender must be
switched on via CTI_AB_EN.
TRANSITION AT THE
OUTPUT OF CTI
Figure 18. CTI Luma/Chroma Transition
Sharp blending maximizes the effect of CTI on the picture, but
may also increase the visual impact of small amplitude, high
frequency chroma noise.
The chroma transient improvement block examines the input
video data. It detects transitions of chroma, and can be
programmed to “steepen” the chroma edges in an attempt to
artificially restore lost color bandwidth. The CTI block,
however, only operates on edges above a certain threshold to
ensure that noise is not emphasized. Care has also been taken to
ensure that edge ringing and undesirable saturation or hue
distortion are avoided.
Table 78. CTI_AB Function
CTI_AB[1:0] Description
00
Sharpest mixing between sharpened and original
chroma signal.
01
Sharp mixing.
10
11*
Smooth mixing.
Smoothest alpha blend function.
Chroma transient improvements are needed primarily for
signals that experienced severe chroma bandwidth limitation.
For those types of signals, it is strongly recommended to enable
the CTI block via CTI_EN.
*Default value.
CTI_C_TH[7:0] CTI Chroma Threshold (SDP),
Address 0x4E, [7:0]
CTI_EN Chroma Transient Improvement Enable (SDP),
Address 0x4D, [0]
The CTI_C_TH[7:0] value is an unsigned, 8-bit number speci-
fying how big the amplitude step in a chroma transition has to
be in order to be steepened by the CTI block. Programming a
small value into this register causes even smaller edges to be
steepened by the CTI block. Making CTI_C_TH[7:0] a large
value causes the block to improve large transitions only.
The CTI_EN bit enables the CTI function. If set to 0, the CTI
block is inactive and the chroma transients are left untouched.
Table 76. CTI_EN Function
CTI_EN
Description
0*
Disable CTI.
Table 79. CTI_C_TH Function
1
Enable CTI block.
CTI_C_TH[7:0] Description
*Default value.
0x0±*
Threshold for chroma edges prior to CTI.
*Default value.
Rev. A | Page 36 of 104
ADV7189
SDP DIGITAL NOISE REDUCTION (DNR)
SDP COMB FILTERS
Digital noise reduction is based on the assumption that high
frequency signals with low amplitude are probably noise, and
that their removal therefore improves picture quality.
The comb filters of the ADV7189 have been greatly improved to
automatically handle video of all types, standards, and levels of
quality. Two user registers are available to customize comb filter
operation.
DNR_EN Digital Noise Reduction Enable (SDP),
Address 0x4D, [5]
Depending on whichever video standard has been detected (by
autodetection) or selected (by manual programming), the
NTSC or PAL configuration registers are used. In addition to
the bits listed in this section, there are some further ADI
internal controls; please contact ADI for more information.
The DNR_EN bit enables the DNR block or bypasses it.
Table 80. DNR_EN Function
DNR_EN
Description
0
Bypass DNR (disable).
NTSC Comb Filter Settings
1*
Enable digital noise reduction on the luma data.
Used for NTSC-M/J CVBS inputs.
DNR_TH[7:0] DNR Noise Threshold, Address 0x50, [7:0]
NSFSEL[1:0] Split Filter Selection NTSC (SDP),
Address 0x19, [3:2]
The DNR_TH[7:0] value is an unsigned 8-bit number used to
determine the maximum edge that will be interpreted as noise
and therefore blanked from the luma data. Programming a large
value into DNR_TH[7:0] causes the DNR block to interpret
even large transients as noise and remove them. The effect on
the video data will therefore be more visible.
The NSFSEL[1:0] control selects how much of the overall signal
bandwidth is fed to the combs. A narrow split filter selection
gives better performance on diagonal lines, but leaves more dot
crawl in the final output image. The opposite is true for
selecting a wide bandwidth split filter.
Programming a small value causes only small transients to be
seen as noise and to be removed.
Table 82.NSFSEL Function
NSFSEL[1:0]
Description
Narrow
Medium
Medium
Wide
00*
01
10
11
It should be noted that the recommended DNR_TH[7:0] setting
for A/V inputs is 0x04, and the recommended DNR_TH[7:0]
setting for tuner inputs is 0x0A.
Table 81. DNR_TH Function
*Default value.
DNR_TH[7:0] Description
0x0±*
Threshold for maximum luma edges to be
interpreted as noise.
CTAPSN[1:0] Chroma Comb Taps NTSC (SDP),
Address 0x38, [7:6]
Table 83. CTAPSN Function
*Default value.
CTAPSN[1:0]
Description
00
01
Do not use.
NTSC chroma comb adapts 3 lines (3 taps) to
2 lines (2 taps).
10*
NTSC chroma comb adapts 5 lines (5 taps) to
3 lines (3 taps).
11
NTSC chroma comb adapts 5 lines (5 taps) to
4 lines (4 taps).
*Default value.
Rev. A | Page 37 of 104
ADV7189
CCMN[2:0] Chroma Comb Mode NTSC (SDP), Address 0x38, [5:3]
Table 84. CCMN Function
CCMN[2:0]
Description
0xx*
Adaptive comb mode.
Adaptive 3-line chroma comb for CTAPSN = 01.
Adaptive 4-line chroma comb for CTAPSN = 10.
Adaptive 5-line chroma comb for CTAPSN = 11.
100
101
Disable chroma comb.
Fixed chroma comb (top lines of line memory).
Fixed 2-line chroma comb for CTAPSN = 01.
Fixed 3-line chroma comb for CTAPSN = 10.
Fixed 4-line chroma comb for CTAPSN = 11.
Fixed 3-line chroma comb for CTAPSN = 01.
Fixed 4-line chroma comb for CTAPSN = 10.
Fixed 5-line chroma comb for CTAPSN = 11.
Fixed 2-line chroma comb for CTAPSN = 01.
Fixed 3-line chroma comb for CTAPSN = 10.
Fixed 4-line chroma comb for CTAPSN = 11.
110
Fixed chroma comb (all lines of line memory).
111
Fixed chroma comb (bottom lines of line memory).
*Default value.
YCMN[2:0] Luma Comb Mode NTSC (SDP), Address 0x38, [2:0]
Table 85.YCMN Function
YCMN[2:0]
Description
0xx*
100
101
110
Adaptive comb mode.
Disable luma comb.
Fixed luma comb (top lines of line memory).
Fixed luma comb (all lines of line memory).
Fixed luma comb (bottom lines of line memory).
Adaptive 3-line (3 taps) luma comb.
Use low-pass/notch filter; see the Y Shaping Filter section.
Fixed 2-line (2 taps) luma comb.
Fixed 3-line (3 taps) luma comb.
Fixed 2-line (2 taps) luma comb.
111
*Default value.
Rev. A | Page 3± of 104
ADV7189
CTAPSP[1:0] Chroma Comb Taps PAL (SDP),
Address 0x39, [7:6]
Table 87. CTAPSP Function
PAL Comb Filter Settings
Used for PAL-B/G/H/I/D, PAL-M, PAL-Combinational N, PAL-
60 and NTSC443 CVBS inputs
CTAPSP[1:0] Description
00
01
Do not use.
PAL chroma comb adapts 5 lines (3 taps) to
3 lines (2 taps); cancels cross luma only.
PSFSEL[1:0] Split Filter Selection PAL (SDP),
Address 0x19, [1:0]
The NSFSEL[1:0] control selects how much of the overall signal
bandwidth is fed to the combs. A wide split filter selection
eliminates dot crawl, but shows imperfections on diagonal lines.
The opposite is true for selecting a narrow bandwidth split
filter.
10
PAL chroma comb adapts 5 lines (5 taps) to
3 lines (3 taps); cancels cross luma and hue error
less well.
PAL chroma comb adapts 5 lines (5 taps) to
4 lines (4 taps); cancels cross luma and hue error
well.
11*
Table 86. PSFSEL Function
*Default value.
PSFSEL[1:0]
Description
Narrow
Medium
Wide
00
01*
10
11
Widest
*Default value.
CCMP[2:0] Chroma Comb Mode PAL (SDP), Address 0x39, [5:3]
Table 88. CCMP Function
CCMP[2:0]
Description
0xx*
Adaptive comb mode.
Adaptive 3-line chroma comb for CTAPSP = 01.
Adaptive 4-line chroma comb for CTAPSP = 10.
Adaptive 5-line chroma comb for CTAPSP = 11.
100
101
Disable chroma comb.
Fixed chroma comb (top lines of line memory).
Fixed 2-line chroma comb for CTAPSP = 01.
Fixed 3-line chroma comb for CTAPSP = 10.
Fixed 4-line chroma comb for CTAPSP = 11.
Fixed 3-line chroma comb for CTAPSP = 01.
Fixed 4-line chroma comb for CTAPSP = 10.
Fixed 5-line chroma comb for CTAPSP = 11.
Fixed 2-line chroma comb for CTAPSP = 01.
Fixed 3-line chroma comb for CTAPSP = 10.
Fixed 4-line chroma comb for CTAPSP = 11.
110
Fixed chroma comb (all lines of line memory).
111
Fixed chroma comb (bottom lines of line memory).
*Default value.
YCMP[2:0] Luma Comb Mode PAL (SDP), Address 0x39, [2:0]
Table 89. YCMP Function
YCMP[2:0]
Description
0xx*
100
Adaptive comb mode.
Disable luma comb.
Adaptive 5 lines (3 taps) luma comb.
Use low-pass/notch filter, see the Y Shaping Filter
section.
101
110
111
Fixed luma comb (top lines of line memory).
Fixed luma comb (all lines of line memory).
Fixed luma comb (bottom lines of line memory).
Fixed 3 lines (2 taps) luma comb.
Fixed 5 lines (3 taps) luma comb.
Fixed 3 lines (2 taps) luma comb.
*Default value.
Rev. A | Page 39 of 104
ADV7189
SDP AV CODE INSERTION AND CONTROLS
This section describes the I2C based controls that affect
In an 8-/10-bit-wide output interface (Cb/Y/Cr/Y interleaved
data), the AV codes are defined as FF/00/00/AV, with AV being
the transmitted word that contains information about H/V/F.
•
•
•
Insertion of AV codes into the data stream
Data blanking during the vertical blank interval (VBI)
In this output interface mode, the following assignment takes
place: Cb = FF, Y = 00, Cr = 00, and Y = AV.
The range of data values permitted in the output data
stream
In a 16-/20-bit output interface where Y and Cr/Cb are
delivered via separate data buses, the AV code is over the whole
20 bits. The SD_DUP_AV bit allows the user to double up the
AV codes, so the full sequence can be found on the Y bus as well
as (= duplicated) the Cr/Cb bus. See Figure 19.
•
The relative delay of luma versus chroma signals
Please note that some of the decoded VBI data is being inserted
during the horizontal blanking interval. See the Gemstar Data
Recovery section for more information.
Table 91. SD_DUP_AV Function
SD_DUP_AV Description
BT656-4 ITU Standard BT-R.656-4 Enable (SDP),
Address 0x04, [7]
0
AV codes in single fashion (to suit ±-/10-bit
interleaved data output).
AV codes duplicated (for 16-/20-bit interfaces).
1
The ITU has changed the position for toggling of the V bit
within the SAV EAV codes for NTSC between revisions 3 and 4.
The BT656-4 standard bit allows the user to select an output
mode that is compliant with either the previous or the new
standard. For further information please review the standard at
http://www.itu.int.
*Default value.
VBI_EN Vertical Blanking Interval Data Enable (SDP),
Address 0x03, [7]
The VBI enable bit allows data such as intercast and closed
caption data to be passed through the luma channel of the SDP
decoder with only a minimal amount of filtering. All data for
lines 1 to 21 is passed through and available at the output port.
The ADV7189 does not blank the luma data, and automatically
switches all filters along the luma data path into their widest
bandwidth. For active video, the filter settings for YSH and YPK
are restored.
Please note that the standard change affects NTSC only and has
no bearing on PAL.
Table 90. BT656-4 Function
BT656-4
Description
0*
BT656-3 Spec: V bit goes low at EAV of lines 10
and 273.
1
BT656-4 Spec: V bit goes low at EAV of lines 20
and 2±3.
Refer to the BL_C_VBI Blank Chroma during VBI section for
information on the chroma path.
*Default value.
Table 92.
VBI_EN
0*
SD_DUP_AV SDP Duplicate AV codes (SDP),
Address 0x03, [0]
Description
All video lines are filtered/scaled.
Only active video region is filtered/scaled.
1
Depending on the output interface width, it may be necessary to
duplicate the AV codes from the luma path into the chroma
path.
*Default value.
SD_DUP_AV = 1
SD_DUP_AV = 0
16-/20-BIT INTERFACE
16-/20-BIT INTERFACE
8-/10-BIT INTERFACE
Y DATA BUS
FF
FF
00
00
AV
AV
Y
00
AV
Y
Cb/Y/Cr/Y
INTERLEAVED
FF
00
00
AV
Cb
Cr/Cb DATA BUS
00
00
Cb
FF
00
Cb
AV CODE SECTION
AV CODE SECTION
AV CODE SECTION
Figure 19. SDP AV Code Duplication Control
Rev. A | Page 40 of 104
ADV7189
BL_C_VBI Blank Chroma during VBI (SDP),
Address 0x04, [2]
Table 95. AUTO_PDC_EN Function
AUTO_PDC_EN Description
0
Use LTA[1:0] and CTA[2:0] values for delaying
luma and chroma samples. Refer to the
LTA[1:0] Luma Timing Adjust (SDP), Address
0x27, [1:0] and CTA[2:0] Chroma Timing
Adjust (SDP), Address 0x27, [5:3] sections.
The ADV71±9 automatically determines the
LTA and CTA values to have luma and chroma
aligned at the output.
Setting BL_C_VBI high, the Cr and Cb values of all VBI lines
get blanked. This is done so any data that may come during VBI
is not decoded as color and output through Cr and Cb. As a
result, it should be possible to send VBI lines into the decoder,
then output them through an encoder again, undistorted.
Without this blanking, any wrongly decoded color gets encoded
by the video encoder; therefore, the VBI lines are distorted.
1*
*Default value.
Table 93. BL_C_VBI Function
BL_C_VBI Description
LTA[1:0] Luma Timing Adjust (SDP), Address 0x27, [1:0]
0
Decode and output color during VBI.
The Luma Timing Adjust register allows the user to specify a
timing difference between chroma and luma samples.
1*
Blank Cr and Cb values during VBI (no color, 0x±0).
*Default value.
Please note the following:
RANGE Range Selection (SDP), Address 0x04, [0]
•
There is a certain functionality overlap with the CTA[2:0]
register.
AV codes (as per ITU-R BT-656, formerly known as CCIR-656)
consist of a fixed header made up of 0xFF and 0x00 values.
These two values are reserved and therefore are not to be used
for active video. Additionally, the ITU also specifies that the
nominal range for video should be restricted to values between
16 and 235 for luma and 16 to 240 for chroma.
•
For manual programming, use the following defaults:
CVBS input LTA[1:0] = 00.
o
o
o
YC input LTA[1:0] = 01.
The RANGE bit allows the user to limit the range of values
output by the ADV7189 to the recommended value range. In
any case, it is ensured that the reserved values of 255d (0xFF)
and 00d (0x00) are not presented on the output pins unless they
are part of an AV code header.
YPrPb input LTA[1:0] =01.
Table 96. LTA Function
LTA[1:0]
Description
00*
No delay.
01
10
11
Luma 1 clk (37 ns) delayed.
Luma 2clk (74 ns) early.
Luma 1 clk (37 ns) early.
Table 94. RANGE Function
RANGE
Description
16 ≤ Y ≤ 235
1 ≤ Y ≤ 254
0
16 ≤ C/P ≤ 240
1 ≤ C/P ≤ 254
*Default value.
1*
*Default value.
CTA[2:0] Chroma Timing Adjust (SDP), Address 0x27, [5:3]
AUTO_PDC_EN Automatic Programmed Delay Control
(SDP), Address 0x27, [6]
The Chroma Timing Adjust register allows the user to specify a
timing difference between chroma and luma samples. This may
be used to compensate for external filter group delay differences
in the luma versus chroma path, and to allow for a different
number of pipeline delays while processing the video down-
stream. Please review this functionality together with the
LTA[1:0] register.
Enabling the AUTO_PDC_EN function activates a function
within the ADV7189 that automatically programs the LTA[1:0]
and CTA[2:0] to have the chroma and luma data match delays
for all modes of operation. If set, manual registers LTA[1:0] and
CTA[2:0] is not used by the SDP. If the automatic mode is
disabled (via setting the AUTO_PDC_EN bit to 0), the values
programmed into LTA[1:0] and CTA[2:0] registers take effect.
Note that the chroma can only be delayed/advanced in chroma
pixel steps. One chroma pixel step is equal to two luma pixels.
The programmable delay occurs after demodulation, where one
can no longer delay by luma pixel steps.
For manual programming use the following defaults:
•
•
•
CVBS input CTA[2:0] = 011.
YC input CTA[2:0] = 101.
YPrPb input CTA[2:0] =110.
Rev. A | Page 41 of 104
ADV7189
Table 97. CTA Function
HSE[10:0] HS End, Address 0x34, [2:0], Address 0x36, [7:0]
CTA[2:0]
Description
The HS Begin and HS End registers allow the user to freely
position the HS output (pin) within the video line. The values in
HSB[10:0] and HSE[10:0] are measured in pixel units from the
falling edge of HS. Using both values, the user can program
both the position and length of the HS output signal.
000
001
010
011*
100
101
110
111
*Default value.
Not used.
Chroma + 2 chroma pixel (early).
Chroma + 1 chroma pixel (early).
No delay.
Chroma – 1 chroma pixel (late).
Chroma – 2 chroma pixel (late).
Chroma – 3 chroma pixel (late).
Not used.
The position of this edge is controlled by placing a binary
number into HSE[10:0]. The number applied offsets the edge
with respect to an internal counter that is reset to 0 immediately
after EAV code FF,00,00,XY (see Figure 20). HSE is set to
00000000000b, which is 0 LLC1 clock cycles from count[0].
SDP SYNCHRONIZATION OUTPUT SIGNALS
HS Configuration
Table 99. HSE Function
HSE[9:0] Description
The following controls allow the user to configure the behavior
of the HS output pin only:
000*
HS pulse ends after HSE[10:0] pixel after falling edge
of HS.
*Default value.
•
•
•
Beginning of HS signal via HSB[10:0]
End of HS signal via HSE[10:0]
Polarity of HS using PHS
Example
1. To shift the HS towards active video by 20 LLC1s, add 20
LLC1s to both HSB and HSE. i.e., HSB[10:0] =
[00000010110], HSE[10:0] = [00000010100]
HSB[10:0] HS Begin, Address 0x34, [6:4], Address 0x35, [7:0]
2. To shift the HS away from active video by 20 LLC1s, add
169611 LLC1s to both HSB and HSE (for NTSC).i.e.,
HSB[10:0] = [11000000100], HSE[10:0] = [11000000110]
The HS Begin and HS End registers allow the user to freely
position the HS output (pin) within the video line. The values in
HSB[10:0] and HSE[10:0] are measured in pixel units from the
falling edge of HS. Using both values, the user can program
both the position and length of the HS output signal.
To move 20 LLC1s away from active video is equal to
subtracting 20 from 1716 and adding the result in binary to
both HSB[10:0] and HSE[10:0].
The position of this edge is controlled by placing a binary
number into HSB[10:0]. The number applied offsets the edge
with respect to an internal counter that is reset to 0 immediately
after EAV code FF,00,00,XY (see Figure 20). HSB is set to
00000000010b, which is 2 LLC1 clock cycles from count[0].
PHS Polarity HS (SDP), Address 0x37, [7]
The polarity of the HS pin as it comes from the SDP block can
be inverted using the PHS bit.
Table 98. HSB Function
HSB[10:0] Description
Table 100. PHS Function
PHS
Description
0x002
The HS pulse starts after the HSB[10:0] pixel after
falling edge of HS.
0*
1
HS active high.
HS active low.
*Default value.
11 1696 is derived from the NTSC total number of pixels = 1716
Rev. A | Page 42 of 104
ADV7189
Table 101. HS Timing Parameters (see Figure 20)
Characteristic
HS to Active Video
(LLC1 Clock Cycles)
(C in Figure 20)1
Active Video
Samples/Line
(D in Figure 20)
Total LLC1
Clock Cycles
(E in Figure 20)
HS Begin Adjust
(HSB[10:0])1
HS End Adjust
(HSE[10:0])1
Standard
NTSC
00000000010b
00000000010b
00000000000b
00000000000b
272
276
720Y + 720C = 1440
640Y + 640C = 12±0
1716
1560
NTSC Square
Pixel
PAL
00000000010b
00000000000b
2±4
720Y + 720C = 1440
172±
1Default.
LLC1
PIXEL
Cr
Y
FF
00
EAV
00
XY
80
10
80
10
80
10
FF
00
00
SAV
XY
Cb
Y
Cr
Y
Cb
Y
Cr
BUS
ACTIVE
VIDEO
H BLANK
ACTIVE VIDEO
HS
HSE[10:0]
4 LLC1
HSB[10:0]
C
D
D
E
E
Figure 20. HS Timing (SDP)
Rev. A | Page 43 of 104
ADV7189
VS and FIELD Configuration
The following controls allow the user to configure the behavior
of the VS and FIELD output pins, as well as the generation of
embedded AV codes:
HVSTIM Horizontal VS Timing (SDP), Address 0x31, [3]
The HVSTIM bit allows the user to select where the VS signal is
being asserted within a line of video. Some interface circuitry
may require VS to go low while HS is low.
•
•
•
•
•
•
ADV encoder compatible signals via NEWAVMODE
Table 103. HVSTIM Function
PVS, PF
HVSTIM
Description
HVSTIM
0*
1
Start of line relative to HSE.
Start of line relative to HSB.
VSBHO, VSBHE
VSEHO, VSEHE
For NTSC control:
*Default value.
VSBHO VS Begin Horizontal Position Odd (SDP),
Address 0x32, [7]
The VSBHO and VSBHE bits select the position within a line at
which the VS pin (not the bit in the AV code) goes active. Some
follow-on chips require the VS pin to only change state when
HS is high/low.
o
o
o
NVBEGDELO, NVBEGDELE, NVBEGSIGN,
NVBEG[4:0]
NVENDDELO, NVENDDELE, NVENDSIGN,
NVEND[4:0]
Table 104. VSBHO Function
VSBHO
Description
NFTOGDELO, NFTOGDELE, NFTOGSIGN,
NFTOG[4:0]
0*
VS pin goes high at the middle of a line of video
(odd field).
1
VS pin changes state at the start of a line (odd
field).
•
For PAL control:
*Default value.
o
o
o
PVBEGDELO, PVBEGDELE, PVBEGSIGN,
PVBEG[4:0]
VSBHE VS Begin Horizontal Position Even (SDP),
Address 0x32, [6]
PVENDDELO, PVENDDELE, PVENDSIGN,
PVEND[4:0]
The VSBHO and VSBHE bits select the position within a line at
which the VS pin (not the bit in the AV code) goes active. Some
follow-on chips require the VS pin to only change state when
HS is high/low.
PFTOGDELO, PFTOGDELE, PFTOGSIGN,
PFTOG[4:0]
Table 105. VSBHE Function
NEWAVMODE New AV Mode, Address 0x31, [4]
Table 102. NEWAVMODE Function
NEWAVMODE Description
VSBHE
Description
0*
VS pin goes high at the middle of a line of video
(even field).
0
EAV/SAV codes generated to suit ADI
encoders. No adjustments possible.
1
VS pin changes state at the start of a line (even field).
*Default value.
1*
Enable Manual Position of VSYNC, Field, and
AV codes using 0x34 to 0x37 and 0xE5 to 0xEA.
Default register settings are CCIR656
VSEHO VS End Horizontal Position Odd (SDP),
Address 0x33, [7]
compliant; see Figure 21 for NTSC and
Figure 26 for PAL. For recommended manual
user settings, see Table 110 and Figure 22 for
NTSC; see Table 123 and Figure 27 for PAL.
The VSEHO and VSEHE bits select the position within a line at
which the VS pin (not the bit in the AV code) goes active. Some
follow-on chips require the VS pin to only change state when
HS is high/low.
*Default value.
Table 106. VSEHO Function
VSEHO
Description
0*
VS pin goes low (inactive) at the middle of a line of
video (odd field).
1
VS pin changes state at the start of a line (odd field).
*Default value.
Rev. A | Page 44 of 104
ADV7189
VSEHE VS End Horizontal Position Even (SDP),
Address 0x33, [6]
PVS Polarity VS (SDP), Address 0x37, [5]
The polarity of the VS pin as it comes from the SDP block can
be inverted using the PVS bit.
The VSEHO and VSEHE bits select the position within a line at
which the VS pin (not the bit in the AV code) goes active. Some
follow-on chips require the VS pin to only change state when
HS is high/low.
Table 108. PVS Function
PVS
Description
VS active high.
VS active low.
0*
1
Table 107. VSEHE Function
VSEHE
Description
*Default value.
0*
VS pin goes low (inactive) at the middle of a line of
video (even field).
PF Polarity FIELD (SDP), Address 0x37, [3]
1
VS pin changes state at the start of a line (even field).
The polarity of the FIELD pin as it comes from the SDP block
can be inverted using the PF bit.
*Default value.
Table 109. PF Function
PF
Description
0*
FIELD active high.
FIELD active low.
1
*Default value.
FIELD 1
525
1
2
3
4
5
6
7
8
9
10
11
12
13
19
20
21
22
OUTPUT
VIDEO
H
V
NVBEG[4:0] = 5h
NVEND[4:0] = 4h
*BT.656-4
REG 04h. BIT 7 = 1
F
NFTOG[4:0] = 3h
FIELD 2
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
283
284
285
OUTPUT
VIDEO
H
V
*BT.656-4
REG 04h. BIT 7 = 1
NVBEG[4:0] = 5h
NVEND[4:0] = 4h
F
NFTOG[4:0] = 3h
*APPLIES IF NEMAVMODE = 0
MUST BE MANUALLY SHIFTED IF NEWAVMODE = 1.
Figure 21. NTSC Default (BT.656). The polarity of H, V, and F is embedded in the data.
Rev. A | Page 45 of 104
ADV7189
FIELD 1
525
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
21
22
OUTPUT
VIDEO
HS
OUTPUT
VS
OUTPUT
FIELD
OUTPUT
NVBEG[4:0] = 0h
NVEND[4:0] = 3h
NFTOG[4:0] = 5h
FIELD 2
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
284
285
OUTPUT
VIDEO
HS
OUTPUT
VS
OUTPUT
NVBEG[4:0] = 0h
NVEND[4:0] = 3h
FIELD
OUTPUT
NFTOG[4:0] = 5h
Figure 22. NTSC Typical VSync/Field Positions Using Register Writes in Table 110
Table 110. Recommended User Settings for NTSC (See Figure 22)
Register
Register Name
VSync Field Control 1
VSync Field Control 2
VSync Field Control 3
Polarity
Write
0x12
0x±1
0x±4
0x29
0x0
0x31
0x32
0x33
0x37
0xE5
NTSV_V_Bit_Beg
NTSC_V_Bit_End
NTSC_F_Bit_Tog
0xE6
0x3
0xE7
0x±5
Rev. A | Page 46 of 104
ADV7189
NVBEGSIGN NTSC VSync Begin Sign, Address 0xE5, [5]
Table 113. NVBEGSIGN Function
1
NVBEGSIGN
0
NVBEGSIGN Description
ADVANCE BEGIN OF
VSYNC BY NVBEG[4:0]
DELAY BEGIN OF
VSYNC BY NVBEG[4:0]
0
Delay start of VSync. Set for user manual
programming.
1*
Advance start of VSync. Not recommended for
user programming.
NOT VALID FOR USER
PROGRAMMING
*Default value.
ODD FIELD?
YES
NO
NVBEG[4:0] NTSC VSync Begin, Address 0xE5, [4:0]
Table 114. NVBEG Function
NVBEG
Description
NVBEGDELO
1
NVBEGDELE
1
00101*
*Default value.
NTSC VSync begin position.
0
0
Note: For all NTSC/PAL VSync timing controls, both the V bit
in the AV code and the VSync on the VS pin are modified.
ADDITIONAL
DELAY BY
1 LINE
ADDITIONAL
DELAY BY
1 LINE
1
NVENDSIGN
0
VSBHO
1
VSBHE
1
ADVANCE END OF
VSYNC BY NVEND[4:0]
DELAY END OF VSYNC
BY NVEND[4:0]
0
0
NOT VALID FOR USER
PROGRAMMING
ADVANCE BY
0.5 LINE
ADVANCE BY
0.5 LINE
ODD FIELD?
YES
NO
VSYNC BEGIN
NVENDDELO
1
NVENDDELE
1
Figure 23. NTSC VSync Begin
0
0
NVBEGDELO NTSC VSync Begin Delay on Odd Field,
Address 0xE5, [7]
Table 111. NVBEGDELO Function
ADDITIONAL
DELAY BY
1 LINE
ADDITIONAL
DELAY BY
1 LINE
NVBEGDELO Description
0*
1
No Delay.
Delay VSync going high on an odd field by a line
relative to NVBEG.
VSEHO
1
VSEHE
1
*Default value.
0
0
NVBEGDELE NTSC Vsync Begin Delay on Even Field,
Address 0xE5, [6]
ADVANCE BY
0.5 LINE
ADVANCE BY
0.5 LINE
Table 112. NVBEGDELE Function
NVBEGDELE Description
0*
1
No Delay.
VSYNC END
Delay VSync going high on an even field by a
line relative to NVBEG.
Figure 24. NTSC VSync End
*Default value.
Rev. A | Page 47 of 104
ADV7189
NVENDDELO NTSC VSync End Delay on Odd Field,
Address 0xE6, [7]
NFTOGSIGN
1
0
Table 115. NVENDDELO Function
NVENDDELO Description
ADVANCE TOGGLE OF
FIELD BY NFTOG[4:0]
DELAY TOGGLE OF
FIELD BY NFTOG[4:0]
0*
1
No Delay.
Delay VSync going low on an odd field by a line
relative to NVEND.
NOT VALID FOR USER
PROGRAMMING
*Default value.
ODD FIELD?
YES
NO
NVENDDELE NTSC VSync End Delay on Even Field,
Address 0xE6, [6]
Table 116. NVENDDELE Function
NFTOGDELO
1
NFTOGDELE
1
NVENDDELE Description
0
0
0*
1
No Delay.
Delay VSync going low on an even field by a line
relative to NVEND.
ADDITIONAL
DELAY BY
1 LINE
ADDITIONAL
DELAY BY
1 LINE
*Default value.
NVENDSIGN NTSC VSync End Sign, Address 0xE6, [5]
Table 117. NVENDSIGN Function
NVENDSIGN Description
FIELD
TOGGLE
0*
Delay start of VSync. Set for user manual
programming.
Figure 25. NTSC FIELD Toggle
1
Advance start of VSync. Not recommended for
user programming.
NFTOGSIGN NTSC Field Toggle Sign, Address 0xE7, [5]
Table 121. NFTOGSIGN Function
*Default value.
NFTOGSIGN Description
0
Delay field transition. Set for user manual
programming.
Advance field transition. Not recommended for
user programming.
NVEND NTSC[4:0] VSync End, Address 0xE6, [4:0]
Table 118. NVEND Function
1*
NVEND
Description
00100*
NTSC VSync end position.
*Default value.
*Default value.
Note: For all NTSC/PAL VSync timing controls, both the V bit
in the AV code and the VSync on the VS pin are modified.
NFTOG[4:0] NTSC Field Toggle, Address 0xE7, [4:0]
Table 122. NFTOG Function
NFTOG
Description
00011*
*Default value.
NTSC FIELD toggle position.
NFTOGDELO NTSC Field Toggle Delay on Odd Field,
Address 0xE7, [7]
Table 119. NFTOGDELO Function
NFTOGDELO Description
Note: For all NTSC/PAL FIELD timing controls, both the F bit
in the AV code and the FIELD signal on the FIELD/DE pin are
modified.
0*
1
No delay.
Delay Field toggle/transition on an odd field by
a line relative to NFTOG.
Table 123. Recommended User Settings for PAL
(See Figure 27)
*Default value.
Register
Register Name
VSync Field Control 1
VSync Field Control 2
VSync Field Control 3
Polarity
Write
0x12
0x±1
0x±4
0x29
0x1
NFTOGDELE NTSC Field Toggle Delay on Even Field,
Address 0xE7, [6]
Table 120. NFTOGDELE Function
0x31
0x32
0x33
NFTOGDELE Description
0x37
0
No Delay
0xE±
PAL_V_Bit_Beg
PAL_V_Bit_End
PAL_F_Bit_Tog
1*
Delay Field toggle/transition on an even field by
a line relative to NFTOG.
0xE9
0x4
0xEA
0x6
*Default value.
Rev. A | Page 4± of 104
ADV7189
FIELD 1
622
623
624
625
1
2
3
4
5
6
7
8
9
10
22
23
24
OUTPUT
VIDEO
H
V
PVBEG[4:0] = 5
PVEND[4:0] = 4
F
PFTOG[4:0] = 3
FIELD 2
310
311
312
313
314
315
316
317
318
319
320
321
322
335
336
337
OUTPUT
VIDEO
H
V
PVBEG[4:0] = 5
PVEND[4:0] = 4
F
PFTOG[4:0] = 3
Figure 26. PAL Default (BT.656). The polarity of H, V, and F is embedded in the data.
FIELD 1
622
623
624
1
2
3
4
5
6
7
8
9
10
11
23
24
625
OUTPUT
VIDEO
HS
OUTPUT
VS
OUTPUT
PVBEG[4:0] = 1h
PVEND[4:0] = 4h
FIELD
OUTPUT
PFTOG[4:0] = 6h
FIELD 2
310
311
312
314
315
316
317
318
319
320
321
322
323
336
337
313
OUTPUT
VIDEO
HS
OUTPUT
VS
OUTPUT
PVBEG[4:0] = 1h
PVEND[4:0] = 4h
FIELD
OUTPUT
PFTOG[4:0] = 6h
Figure 27. PAL Typical VSync/Field Positions Using Register Writes in Table 123
Rev. A | Page 49 of 104
ADV7189
PVBEGSIGN PAL VSync Begin Sign, Address 0xE8, [5]
Table 126. PVBEGSIGN Function
PVBEGSIGN
1
0
PVBEGSIGN Description
ADVANCE BEGIN OF
VSYNC BY PVBEG[4:0]
DELAY BEGIN OF
VSYNC BY PVBEG[4:0]
0
Delay begin of VSync. Set for user manual
programming.
1*
Advance begin of VSync. Not recommended for
user programming.
NOT VALID FOR USER
PROGRAMMING
*Default value.
ODD FIELD?
YES
NO
PVBEG[4:0] PAL VSync Begin, Address 0xE8, [4:0]
Table 127. PVBEG Function
PVBEG
Description
PVBEGDELO
1
PVBEGDELE
1
00101*
*Default value.
PAL VSync begin position.
0
0
For all NTSC/PAL VSync timing controls, both the V bit in the
AV code and the VSync on the VS pin are modified.
ADDITIONAL
DELAY BY
1 LINE
ADDITIONAL
DELAY BY
1 LINE
1
PVENDSIGN
0
VSBHO
1
VSBHE
1
ADVANCE END OF
VSYNC BY PVEND[4:0]
DELAY END OF VSYNC
BY PVEND[4:0]
0
0
NOT VALID FOR USER
PROGRAMMING
ADVANCE BY
0.5 LINE
ADVANCE BY
0.5 LINE
ODD FIELD?
YES
NO
VSYNC BEGIN
PVENDDELO
1
PVENDDELE
1
Figure 28. PAL VSync Begin
0
0
PVBEGDELO PAL VSync Begin Delay on Odd Field,
Address 0xE8, [7]
Table 124. PVBEGDELO Function
ADDITIONAL
DELAY BY
1 LINE
ADDITIONAL
DELAY BY
1 LINE
PVBEGDELO Description
0*
1
No delay.
Delay VSync going high on an odd field by a line
relative to PVBEG.
VSEHO
1
VSEHE
1
*Default value.
0
0
PVBEGDELE PAL VSync Begin Delay on Even Field,
Address 0xE8, [6]
ADVANCE BY
0.5 LINE
ADVANCE BY
0.5 LINE
Table 125. PVBEGDELE Function
PVBEGDELE Description
0
No delay.
VSYNC END
1*
Delay VSync going high on an even field by a line
relative to PVBEG.
Figure 29. PAL VSync End
*Default value.
PVENDDELO PAL VSync End Delay on Odd Field,
Address 0xE9,[7]
Table 128. PVENDDELO Function
PVENDDELO Description
0*
1
No delay.
Delay VSync going low on an odd field by a line
relative to PVEND.
*Default value.
Rev. A | Page 50 of 104
ADV7189
PVENDDELE PAL VSync End Delay on Even Field,
Address 0xE9,[6]
PFTOG PAL Field Toggle, Address 0xEA [4:0]
Table 135. PFTOG Function
Table 129. PVENDDELE Function
PFTOG
Description
PVENDDELE Description
00011*
PAL Field toggle position.
*Default value.
0*
1
No delay.
Delay VSync going low on an even field by a line
relative to PVEND.
For all NTSC/PAL Field timing controls, the F bit in the AV
code and the Field signal on the FIELD/DE pin are modified.
*Default value.
PVENDSIGN PAL VSync End Sign, Address 0xE9, [5]
Table 130. PVENDSIGN Function
PFTOGSIGN
1
0
PVENDSIGN Description
ADVANCE TOGGLE OF
FIELD BY PTOG[4:0]
DELAY TOGGLE OF
FIELD BY PFTOG[4:0]
0*
Delay end of VSync. Set for user manual
programming.
NOT VALID FOR USER
PROGRAMMING
1
Advance end of VSync. Not recommended for
user programming.
ODD FIELD?
*Default value.
YES
NO
PVEND[4:0] PAL Vsync End, Address 0xE9,[4:0]
Table 131. PVEND Function
PFTOGDELO
1
PFTOGDELE
1
PVEND
Description
10100*
PAL VSync end position.
0
0
*Default value.
ADDITIONAL
DELAY BY
1 LINE
ADDITIONAL
DELAY BY
1 LINE
Note: For all NTSC/PAL VSync timing controls, both the V bit
in the AV code and the VSync on the VS pin are modified.
PFTOGDELO PAL Field Toggle Delay on Odd Field,
Address 0xEA, [7]
Table 132. PFTOGDELO Function
FIELD
TOGGLE
Figure 30. PAL F Toggle
PFTOGDELO Description
0*
1
No delay.
SDP SYNC PROCESSING
Delay F toggle/transition on an odd field by a
line relative to PFTOG.
The ADV7189 has two additional sync processing blocks that
postprocess the raw synchronization information extracted
from the digitized input video. If desired, the blocks can be
disabled via the following two I2C bits.
*Default value.
PFTOGDELE PAL Field Toggle Delay on Even Field,
Address 0xEA [6]
Table 133. PFTOGDELE Function
PFTOGDELE Description
ENHSPLL Enable HSync Processor (SDP), Address 0x01, [6]
The HSYNC processor is designed to filter incoming HSyncs
that have been corrupted by noise, providing improved per-
formance for video signals with stable time bases but poor SNR.
0
No delay.
1*
Delay F toggle/transition on an even field by a
line relative to PFTOG.
*Default value.
For CVBS PAL/NTSC, YC PAL/NTSC enable the HSync
processor. For SECAM disable the HSync Processor. For YPrPb,
through SDP, disable HSYNC Processor.
PFTOGSIGN PAL Field Toggle Sign, Address 0xEA, [5]
Table 134. PFTOGSIGN Function
PFTOGSIGN Description
Table 136. ENHSPLL Function
ENHSPLL
Description
0
Delay Field transition. Set for user manual
programming.
Advance Field transition. Not recommended for
user programming.
0
1*
Disable the HSync processor.
Enable the HSync processor.
1*
*Default value.
*Default value.
Rev. A | Page 51 of 104
ADV7189
ENVSPROC Enable VSync Processor (SDP),
Address 0x01, [3]
WSSD Wide Screen Signaling Detected (SDP),
Address 0x90, [0]
This block provides extra filtering of the detected VSyncs to
give improved vertical lock.
Logic 1 for this bit indicates that the data in the WSS1 and
WSS2 registers is valid.
Table 137. ENVSPROC Function
The WSSD bit goes high if the rising edge of the start bit is
detected within a time window, and if the polarity of the parity
bit matches the data transmitted.
ENVSPROC
Description
0
1*
Disable VSync processor.
Enable VSync processor.
Table 138. WSSD Function
*Default value.
WSSD Description
SDP VBI DATA DECODE
0
1
No WSS detected. Confidence in decoded data is low.
WSS detected. Confidence in decoded data is high.
The following low data rate VBI signals can be decoded by the
ADV7189:
CCAPD Closed Caption Detected (SDP), Address 0x90, [1]
•
•
•
•
•
Wide screen signaling (WSS)
Copy generation management systems (CGMS)
Closed captioning (CCAP)
Logic 1 for this bit indicates that the data in the CCAP1 and
CCAP2 registers is valid.
The CCAPD bit goes high if the rising edge of the start bit is
detected within a time window, and if the polarity of the parity
bit matches the data transmitted.
EDTV
Table 139. CCAPD Function
CCAPD Description
Gemstar 1× and 2× compatible data recovery
The presence of any of the above signals is detected and, if
applicable, a parity check is performed. The result of this testing
is contained in a confidence bit in the VBI Info[7:0] register.
Users are encouraged to first examine the VBI Info register
before reading the corresponding data registers. All VBI data
decode bits are read-only.
0
No CCAP signals detected. Confidence in decoded
data is low.
CCAP sequence detected. Confidence in decoded data
is high.
1
EDTVD EDTV Sequence Detected (SDP), Address 0x90, [2]
Logic 1 for this bit indicates that the data in the EDTV1, 2, 3
registers is valid.
All VBI data registers are double-buffered with the field signals.
This means that data is extracted from the video lines and
appears in the appropriate I2C registers with the next field
transition. They are then static until the next field.
The EDTVD bit goes high if the rising edge of the start bit is
detected within a time window, and if the polarity of the parity
bit matches the data transmitted.
The user should start an I2C read sequence with VS by first
examining the VBI Info register. Then, depending on what data
was detected, the appropriate data registers should be read.
Table 140. EDTVD Function
EDTVD Description
0
No EDTV sequence detected. Confidence in decoded
data is low.
Note that the data registers are filled with decoded VBI data
even if their corresponding detection bits are low; it is likely
that bits within the decoded data stream are wrong.
1
EDTV sequence detected. Confidence in decoded data
is high.
CGMSD CGMS-A Sequence Detected (SDP),
Address 0x90, [3]
Notes
•
The closed captioning data (CCAP) is available in the I2C
registers, and is also inserted into the output video data
stream during horizontal blanking.
Logic 1 for this bit indicates that the data in the CGMS1, 2, 3
registers is valid. The CGMSD bit goes high if a valid CRC
checksum has been calculated from a received CGMS packet.
•
The Gemstar compatible data is not available in the I2C
registers, and is inserted into the data stream only during
horizontal blanking.
Table 141. CGMSD Function
CGMSD
Description
0
1
No CGMS transmission detected, confidence low
CGMS sequence decoded, confidence high
Rev. A | Page 52 of 104
ADV7189
CRC_ENABLE CRC CGMS-A Sequence (SDP),
Address 0xB2, [2]
Wide Screen Signaling Data
WSS1[7:0] (SDP), Address 0x91, [7:0], WSS2[7:0] (SDP),
Address 0x92, [7:0]
For certain video sources, the CRC data bits may have an
invalid format. In such circumstances, the CRC checksum
validation procedure can be disabled. The CGMSD bit goes
high if the rising edge of the start bit is detected within a time
window.
Figure 31 shows the bit correspondence between the analog
video waveform and the WSS1/WSS2 registers. Note that
WSS2[7:6] are undetermined and should be masked out by
software.
Table 142. CRC_ENABLE Function
CRC_ENABLE Description
EDTV Data Registers
0
No CRC check performed. The CGMSD bit goes
high if the rising edge of the start bit is detected
within a time window.
EDTV1[7:0] (SDP), Address 0x93, [7:0], EDTV2[7:0] (SDP),
Address 0x94, [7:0], EDTV3[7:0] (SDP), Address 0x95, [7:0]
1*
Use CRC checksum to validate the CGMS-A
sequence. The CGMSD bit goes high for a valid
checksum. ADI recommended setting.
Figure 32 shows the bit correspondence between the analog
video waveform and the EDTV1/EDTV2/EDTV3 registers.
*Default value.
Note that EDTV3[7:6] are undetermined and should be masked
out by software. EDTV3[5] is reserved for future use and, for
now, will contain 0. The three LSBs of the EDTV waveform are
currently not supported.
WSS1[7:0]
WSS2[5:0]
0
1
2
3
4
5
6
7
0
1
2
3
4
5
RUN-IN
SEQUENCE
START
CODE
ACTIVE
VIDEO
11.0µs
38.4µs
42.5µs
Figure 31. SDP WSS Data Extraction
Table 143. SDP WSS Access Information
Signal Name
WSS1 [7:0]
WSS2 [5:0]
Block
Register Location
Address
Register Default Value
Readback Only
Readback Only
SDP
SDP
WSS 1 [7:0]
WSS 2 [5:0]
145d
146d
91h
92h
EDTV1[7:0]
EDTV2[7:0]
EDTV3[5:0]
0
1
2
NOT SUPPORTED
4 5
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
Figure 32. SDP EDTV Data Extraction
Table 144. SDP EDTV Access Information
Signal Name
EDTV1[7:0]
EDTV2[7:0]
EDTV3[7:0]
Block
Register Location
Address
Register Default Value
SDP
SDP
SDP
EDTV 1 [7:0]
EDTV 2 [7:0]
EDTV 3 [7:0]
147d
14±d
149d
93h
94h
95h
Readback Only
Readback Only
Readback Only
Rev. A | Page 53 of 104
ADV7189
CGMS Data Registers
Closed Caption Data Registers
CGMS1[7:0] (SDP), Address 0x96, [7:0], CGMS2[7:0] (SDP),
Address 0x97, [7:0], CGMS3[7:0] (SDP), Address 0x98, [7:0]
CCAP1[7:0] (SDP), Address 0x99, [7:0], CCAP2[7:0] (SDP),
Address 0x9A, [7:0]
Figure 33 shows the bit correspondence between the analog
video waveform and the CGMS1/CGMS2/CGMS3 registers.
CGMS3[7:4] are undetermined and should be masked out by
software.
Figure 34 shows the bit correspondence between the analog
video waveform and the CCAP1/CCAP2 registers.
Notes
•
CCAP1[7] contains the parity bit from the first word.
CCAP2[7] contains the parity bit from the second word.
•
Please refer to the GDECAD Gemstar Decode Ancillary
Data Format (SDP), Address 0x4C, [0] section.
+100 IRE
REF
CGMS1[7:0]
CGMS2[7:0]
CGMS3[3:0]
+70 IRE
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
0 IRE
49.1µs
± 0.5µs
–40 IRE
11.2µs
CRC SEQUENCE
2.235µs
± 20ns
Figure 33. SDP CGMS Data Extraction
Table 145. SDP CGMS Access Information
Signal Name
CGMS1[7:0]
CGMS2[7:0]
CGMS3[3:0]
Block
Register Location
Address
96h
Register Default Value
Readback Only
Readback Only
SDP
SDP
SDP
CGMS 1 [7:0]
CGMS 2 [7:0]
CGMS 3 [3:0]
150d
151d
152d
97h
9±h
Readback Only
10.5
±
0.25µs
12.91µs
7 CYCLES
OF 0.5035MHz
(CLOCK RUN-IN)
CCAP1[7:0]
CCAP2[7:0]
0 1
2
3
4 5
6
7
0
1
2 3
4
5
6
7
S
T
A
R
T
P
A
R
I
T
Y
P
A
R
I
T
Y
50 IRE
40 IRE
BYTE 0
BYTE 1
REFERENCE COLOR BURST
(9 CYCLES)
FREQUENCY = F = 3.579545MHz
SC
AMPLITUDE = 40 IRE
10.003µs
27.382µs
33.764µs
Figure 34. SDP Closed Caption Data Extraction
Table 146. SDP CCAP Access Information
Signal Name
CCAP1[7:0]
CCAP2[7:0]
Block
Register Location
Address
99h
9Ah
Register Default Value
Readback Only
Readback Only
SDP
SDP
CCAP 1 [7:0]
CCAP 2 [7:0]
153d
154d
Rev. A | Page 54 of 104
ADV7189
Letterbox Detection
•
There is no “letterbox detected” bit. The user is asked to
read the LB_LCT[7:0] and LB_LCB[7:0] register values and
to come to a conclusion about the presence of letterbox
type video in software.
Incoming video signals may conform to different aspect ratios
(16:9 wide screen of 4:3 standard). For certain transmissions in
the wide screen format, a digital sequence (WSS) is transmitted
with the video signal. If a WSS sequence is provided, the aspect
ratio of the video can be derived from the digitally decoded bits
WSS contains.
LB_LCT[7:0] Letterbox Line Count Top (SDP), Address
0x9B, [7:0]; LB_LCM[7:0] Letterbox Line Count Mid (SDP),
Address 0x9C, [7:0]; LB_LCB[7:0] Letterbox Line Count
Bottom (SDP), Address 0x9D, [7:0]
In the absence of a WSS sequence, letterbox detection may be
used to find wide screen signals. The detection algorithm
examines the active video content of lines at the start and end of
a field. If black lines are detected, this may serve as an indication
that the currently shown picture is in wide screen format.
Table 147. LB_LCx Access Information
Signal Name
LB_LCT[7:0]
LB_LCM[7:0]
LB_LCB[7:0]
Block Address
Register Default Value
SDP
SDP
SDP
0x9B
0x9C
0x9D
Readback only
Readback only
Readback only
The active video content (luminance magnitude) over a line of
video is summed together. At the end of a line, this accumulated
value is compared with a threshold, and a decision is made as to
whether or not a particular line is black. The threshold value
needed may depend on the type of input signal; some control is
provided via LB_TH[4:0].
LB_TH[4:0] Letterbox Threshold Control (SDP),
Address 0xDC, [4:0]
Table 148. LB_TH Function
LB_TH[4:0]
Description
01100*
Default threshold for detection of black lines.
01101 to
10000
Increase threshold (need larger active video
content before identifying nonblack lines).
Detection at the Start of a Field
The ADV7189 expects a section of at least six consecutive black
lines of video at the top of a field. Once those lines have been
detected, Register LB_LCT[7:0] reports back the number of
black lines that were actually found. By default, the ADV7189
starts looking for those black lines in sync with the beginning of
active video (e.g., straight after the last VBI video line).
LB_SL[3:0] allows the user to set the start of letterbox detection
from the beginning of a frame on a line-by-line basis. The
detection window closes in the middle of the field.
00000 to
01011
*Default value.
Decrease threshold (even small noise levels can
cause the detection of nonblack lines).
LB_SL [3:0] Letterbox Start Line (SDP), Address 0xDD, [7:4]
Table 149. LB_SL Function
LB_SL[3:0]
Description
0100*
Letterbox detection is aligned with active video.
Window starts after the EDTV VBI data line. For
example, 0100 = 23/2±6 (NTSC).
0001, 0010
*Default value.
For example, 0101 = 24/2±7 (NTSC).
Detection at the End of a Field
The ADV7189 expects at least six continuous lines of black
video at the bottom of a field before reporting back the number
of lines actually found via the LB_LCB[7:0] value. The activity
window for letterbox detection (end of field) starts in the
middle of an active field. Its end is programmable via
LB_EL[3:0].
LB_EL[3:0] Letterbox End Line (SDP), Address 0xDD, [3:0]
Table 150. LB_EL Function
LB_EL[3:0] Description
1101*
Letterbox detection ends with the last active line
of video on a field. For example, 1101 = 262/ 525
(NTSC).
0001,0010
*Default value.
For example, 1100 = 261/524 (NTSC).
Detection at the Midrange
Gemstar Data Recovery
Some transmissions of wide screen video include subtitles
within the lower black box. If the ADV7189 finds at least two
black lines followed by some more nonblack video (e.g.,. the
subtitle) and finally followed by the remainder of the bottom
black block, it reports back a midcount via LB_LCM[7:0]. In
cases where no subtitles are found, LB_LCM[7:0] reports the
same number as LB_LCB[7:0].
The Gemstar compatible data recovery block (GSCD) supports
1× and 2× data transmissions. In addition, it can serve as a
closed caption decoder. Gemstar compatible data transmissions
can occur only in NTSC. Closed caption data can be decoded in
both PAL and NTSC.
The block is configured via I2C in the following ways:
Notes
•
GDECEL[15:0] allow data recovery on selected video lines
on even fields to be enabled and disabled.
GDECOL[15:0] enable the data recovery on selected lines
for odd fields.
•
There is a 2-field delay in the reporting of any line count
parameters.
•
Rev. A | Page 55 of 104
ADV7189
Entries within the packet are as follows:
•
GDECAD configures the way in which data is embedded
in the video data stream.
•
•
Fixed preamble sequence of 0x00, 0xFF, 0xFF.
The recovered data is not available through I2C, but is being
inserted into the horizontal blanking period of an ITU-R.
BT656 compatible data stream. The data format is intended to
comply with the recommendation by the International
Telecommunications Union, ITU-R BT.13642. See Figure 35.
Data identification word (DID). The value for the DID
marking a Gemstar or CCAP data packet is 0x140 (10-bit
value).
•
Secondary data identification word (SDID), which contains
information about the video line from which data was
retrieved, whether the Gemstar transmission was of 1× or
2× format, and whether it was retrieved from an even or
odd field.
The format of the data packet depends on the following criteria:
•
•
Transmission is 1× or 2×
Data is output in 8-bit or 4-bit format (see the description
of the GDECAD Gemstar Decode Ancillary Data Format
(SDP), Address 0x4C, [0] bit)
•
Data count byte, giving the number of user data-words that
follow.
•
Data is Closed Caption (CCAP) or Gemstar compatible
•
•
User data section.
Data packets are output if the corresponding enable bit is set
(see the GDECEL and GDECOL descriptions), and if the
decoder detects the presence of data. This means that for video
lines where no data has been decoded, no data packet is output
even if the corresponding line enable bit is set.
Optional padding to ensure that the length of the user
data-word section of a packet is a multiple of four bytes3.
•
Checksum byte.
Table 151 lists the values within a generic data packet that is
output by the ADV7189 in 10-bit format.
Each data packet starts immediately after the EAV code of the
preceding line. Refer to Figure 35 and Table 151, which show
the overall structure of the data packet.
2 For more information, see the ITU website at www.itu.ch.
3Requirement as set in ITU-R BT.1364.
DATA IDENTIFICATION
SECONDARY DATA IDENTIFICATION
DATA
COUNT
OPTIONAL PADDING CHECK
00
FF
FF
DID
SDID
USER DATA
BYTES
SUM
PREAMBLE FOR ANCILLARY DATA
USER DATA (4 OR 8 WORDS)
Figure 35. Gemstar and CCAP Embedded Data Packet (Generic)
Table 151. Generic Data Output Packet
Byte
D[9]
D[8]
D[7]
D[6]
D[5]
D[4]
D[3]
D[2]
D[1]
D[0]
0
Description
0
0
0
0
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
0
Fixed preamble
Fixed preamble
Fixed preamble
DID
1
1
1
1
1
1
2
1
1
1
1
1
3
0
1
0
1
0
4
!EP
!EP
!EP
!EP
!EP
!EP
!EP
!EP
!EP
!EP
!CS[±]
EP
EP
EP
EP
EP
EP
EP
EP
EP
EP
CS[±]
EF
0
2X
0
line[3:0]
0
SDID
5
0
0
DC[1]
word1[7:4]
word1[3:0]
word2[7:4]
word2[3:0]
word3[7:4]
word3[3:0]
word4[7:4]
word4[3:0]
DC[0]
0
Data count (DC)
User data-words
User data-words
User data-words
User data-words
User data-words
User data-words
User data-words
User data-words
Checksum
6
0
0
0
7
0
0
0
±
0
0
0
9
0
0
0
10
11
12
13
14
0
0
0
0
0
0
0
0
0
0
0
0
CS[7]
CS[6]
CS[5]
CS[4]
CS[3]
CS[2]
0
Rev. A | Page 56 of 104
ADV7189
Table 152. Data Byte Allocation
Raw Information Bytes
Retrieved from the Video Line
User Data-Words
(Including Padding)
2×
1
1
0
0
GDECAD
Padding Bytes
DC[1:0]
10
01
01
01
4
4
2
2
0
1
0
1
±
4
4
4
0
0
0
2
Notes
•
CS[8:2]. The checksum is provided to determine the
integrity of the ancillary data packet. It is calculated by
summing up D[8:2] of DID, SDID, the Data Count byte,
and all UDWs, and ignoring any overflow during the
summation. Since all data bytes that are used to calculate
the checksum have their 2 LSBs set to 0, the CS[1:0] bits are
also always 0.
•
DID. The data identification value is 140h (10-bit value).
Care has been taken that in 8-bit systems, the 2 LSBs do
not carry vital information.
•
EP and !EP. The EP bit is set to ensure even parity on the
data-word D[8:0]. Even parity means there will always be
an even number of 1s within the D[8:0] bit arrangement.
This includes the EP bit. !EP describes the logic inverse of
EP and is output on D[9]. The !EP is output to ensure that
the reserved codes of 00 and FF cannot happen.
!CS[8] describes the logic inversion of CS[8]. The value
!CS[8] is included in the checksum entry of the data packet
to ensure that the reserved values of 0x00 and 0xFF do not
occur.
•
•
•
EF. Even field identifier. EF = 1 indicates that the data was
recovered from a video line on an even field.
Table 153 to Table 156 outline the possible data packages.
Gemstar 2× Format, Half-Byte Output
2X. This bit indicates whether the data sliced was in
Gemstar 1× or 2× format. A high indicates 2× format.
Half-byte output mode is selected by setting CDECAD = 0;
full-byte output mode is selected by setting CDECAD = 1. See
the GDECAD Gemstar Decode Ancillary Data Format (SDP),
Address 0x4C, [0] section.
line[3:0]. This entry provides a code that is unique for each
of the possible 16 source lines of video from which
Gemstar data may have been retrieved. See Table 164 and
Table 165.
Gemstar 1× Format
Half-byte output mode is selected by setting CDECAD = 0,
full-byte output mode is selected by setting CDECAD = 1. See
the GDECAD Gemstar Decode Ancillary Data Format (SDP),
Address 0x4C, [0] section.
•
•
DC[1:0]. Data count value. The number of user data-words
in the packet divided by 4. The number of user data words
(UDW) in any packet must be an integral number of 4.
Padding is required at the end if necessary12. See Table 152.
The 2X bit determines whether the raw information
retrieved from the video line was 2 or 4 bytes. The state of
the GDECAD bit affects whether the bytes are transmitted
straight (i.e., two bytes transmitted as two bytes) or
whether they are split into nibbles (i.e., two bytes
transmitted as four half bytes). Padding bytes are then
added where necessary.
12 Requirement as set in ITU-R BT.1364.
Rev. A | Page 57 of 104
ADV7189
Table 153. Gemstar 2× Data, Half-Byte Mode
Byte
D[9]
D[8]
D[7]
D[6]
D[5]
D[4]
D[3]
D[2]
D[1]
D[0]
Description
0
0
0
0
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
0
Fixed preamble
Fixed preamble
Fixed preamble
DID
1
1
1
1
1
1
1
2
1
1
1
1
1
1
3
0
1
0
1
0
0
4
!EP
!EP
!EP
!EP
!EP
!EP
!EP
!EP
!EP
!EP
!CS[±]
EP
EP
EP
EP
EP
EP
EP
EP
EP
EP
CS[±]
EF
0
1
line[3:0]
0
0
SDID
5
0
0
0
0
0
Data count
1
0
6
0
0
Gemstar word1[7:4]
Gemstar word1[3:0]
Gemstar word2[7:4]
Gemstar word2[3:0]
Gemstar word3[7:4]
Gemstar word3[3:0]
Gemstar word4[7:4]
Gemstar word4[3:0]
0
0
User data-words
User data-words
User data-words
User data-words
User data-words
User data-words
User data-words
User data-words
Checksum
7
0
0
0
0
±
0
0
0
0
9
0
0
0
0
10
11
12
13
14
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
CS[7]
CS[6]
CS[5]
CS[4]
CS[3]
CS[2]
CS[1]
CS[0]
Table 154. Gemstar 2× Data, Full-Byte Mode
Byte
D[9]
D[8]
D[7]
D[6]
D[5]
D[4]
D[3]
D[2]
D[1]
0
D[0]
Description
0
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
0
1
1
0
0
Fixed preamble
Fixed preamble
Fixed preamble
DID
1
1
1
1
1
1
1
2
1
1
1
1
1
1
3
0
1
0
0
line[3:0]
0
0
0
4
!EP
!EP
EP
EP
EF
0
0
0
SDID
5
0
0
0
0
Data count
1
6
Gemstar word1[7:0]
Gemstar word2[7:0]
Gemstar word3[7:0]
Gemstar word4[7:0]
0
0
User data-words
User data-words
User data-words
User data-words
Checksum
7
0
0
±
0
0
9
0
0
10
!CS[±]
CS[±]
CS[7]
CS[6]
CS[5]
CS[4]
CS[3]
CS[2]
CS[1]
CS[0]
Table 155. Gemstar 1× Data, Half-Byte Mode
Byte
D[9]
D[8]
D[7]
D[6]
D[5]
D[4]
D[3]
D[2]
D[1]
D[0]
0
Description
Fixed preamble
Fixed preamble
Fixed preamble
DID
0
0
0
0
0
0
1
1
0
0
1
1
0
0
0
1
1
0
0
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
3
0
1
0
1
0
line[3:0]
0
0
0
4
!EP
!EP
!EP
!EP
!EP
!EP
!CS[±]
EP
EP
EP
EP
EP
EP
CS[±]
EF
0
0
SDID
0
5
0
0
0
0
0
0
Data count
1
6
0
0
Gemstar word1[7:4]
Gemstar word1[3:0]
Gemstar word2[7:4]
Gemstar word2[3:0]
0
0
User data-words
User data-words
User data-words
User data-words
7
0
0
0
0
±
0
0
0
0
9
0
0
0
0
10
CS[7]
CS[6]
CS[5]
CS[4]
CS[3]
CS[2]
CS[1]
CS[0]
Checksum
Rev. A | Page 5± of 104
ADV7189
Table 156. Gemstar 1× Data, Full-Byte Mode
Byte
D[9]
D[8]
D[7]
D[6]
D[5]
D[4]
D[3]
D[2]
D[1]
D[0]
Description
0
0
0
0
0
1
1
1
0
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
0
Fixed preamble
Fixed preamble
Fixed preamble
DID
1
1
1
1
1
1
2
1
1
1
1
1
3
0
1
0
0
0
4
!EP
!EP
EP
EP
EF
0
line[3:0]
0
0
SDID
5
0
0
0
0
Data count
0
1
6
Gemstar word1[7:0]
Gemstar word2[7:0]
0
0
User data-words
User data-words
UDW padding 200h
UDW padding 200h
Checksum
7
0
0
±
1
0
0
0
0
0
0
0
0
0
9
1
0
0
0
0
0
0
0
0
0
10
!CS[±]
CS[±]
CS[7]
CS[6]
CS[5]
CS[4]
CS[3]
CS[2]
CS[1]
CS[0]
Table 157. NTSC CCAP Data, Half-Byte Mode
Byte
D[9]
D[8]
D[7]
D[6]
D[5]
D[4]
D[3]
D[2]
D[1]
D[0]
Description
Fixed preamble
Fixed preamble
Fixed preamble
DID
0
0
0
0
0
0
1
1
0
1
0
0
1
1
0
0
0
0
1
1
0
1
0
0
1
1
0
1
1
0
0
1
1
1
1
1
1
1
2
1
1
1
1
1
1
3
0
1
0
1
0
0
4
!EP
!EP
!EP
!EP
!EP
!EP
!CS[±]
EP
EP
EP
EP
EP
EP
CS[±]
EF
0
0
SDID
0
5
0
0
0
0
Data count
6
0
0
CCAP word1[7:4]
CCAP word1[3:0]
CCAP word2[7:4]
CCAP word2[3:0]
0
0
User data-words
User data-words
User data-words
User data-words
Checksum
7
0
0
0
0
±
0
0
0
0
9
0
0
0
0
10
CS[7]
CS[6]
CS[5]
CS[4]
CS[3]
CS[2]
CS[1]
CS[0]
Table 158. NTSC CCAP Data, Full-Byte Mode
Byte
D[9]
D[8]
D[7]
D[6]
D[5]
D[4]
D[3]
D[2]
D[1]
D[0]
Description
Fixed preamble
Fixed preamble
Fixed preamble
DID
0
0
0
0
0
1
1
1
0
0
0
1
1
0
1
0
0
1
1
0
0
0
0
1
1
0
1
0
0
1
1
0
1
1
0
0
1
1
1
1
1
1
2
1
1
1
1
1
3
0
1
0
0
0
4
!EP
!EP
EP
EP
EF
0
0
0
SDID
5
0
0
Data count
6
CCAP word1[7:0]
CCAP word2[7:0]
0
0
User data-words
User data-words
UDW padding 200h
UDW padding 200h
Checksum
7
0
0
±
1
0
0
0
0
0
0
0
0
0
9
1
0
0
0
0
0
0
0
0
0
10
!CS[±]
CS[±]
CS[7]
CS[6]
CS[5]
CS[4]
CS[3]
CS[2]
CS[1]
CS[0]
NTSC CCAP Data
Notes
Half-byte output mode is selected by setting CDECAD = 0, the
full-byte mode is enabled by CDECAD = 1. See the GDECAD
Gemstar Decode Ancillary Data Format (SDP), Address 0x4C,
[0] section. The data packet formats are shown in Table 157 and
Table 158.
•
Only closed caption data from the SDP core can be
embedded in the output data stream.
•
NTSC closed caption data is sliced on line 21d on even and
odd fields. The corresponding enable bit has to be set high.
See the GDECEL[15:0] Gemstar Decoding Even Lines
(SDP), Address 0x48, [7:0]; Address 0x49, [7:0] and
GDECOL[15:0] Gemstar Decoding Odd Lines (SDP),
Address 0x4A, [7:0]; Address 0x4B, [7:0] sections.
Rev. A | Page 59 of 104
ADV7189
PAL CCAP Data
Notes
Half-Byte output mode is selected by setting CDECAD = 0,
full-byte output mode is selected by setting CDECAD = 1. See
the GDECAD Gemstar Decode Ancillary Data Format (SDP),
Address 0x4C, [0] section. Table 159 and Table 160 list the bytes
of the data packet.
•
Only closed caption data from the SDP core can be
embedded in the output data stream. PAL closed caption
data is sliced from lines 22 and 335. The corresponding
enable bits have to be set.
•
See the GDECEL[15:0] Gemstar Decoding Even Lines
(SDP), Address 0x48, [7:0]; Address 0x49, [7:0] and
GDECOL[15:0] Gemstar Decoding Odd Lines (SDP),
Address 0x4A, [7:0]; Address 0x4B, [7:0] sections.
Table 159. PAL CCAP Data, Half-Byte Mode
Byte
D[9]
D[8]
D[7]
D[6]
D[5]
D[4]
D[3]
D[2]
D[1]
D[0]
Description
Fixed preamble
Fixed preamble
Fixed preamble
DID
0
0
0
0
0
0
1
1
0
1
0
0
1
1
0
0
0
0
1
1
0
1
0
0
1
1
0
0
1
0
0
1
1
1
1
1
1
1
2
1
1
1
1
1
1
3
0
1
0
1
0
0
4
!EP
!EP
!EP
!EP
!EP
!EP
!CS[±]
EP
EP
EP
EP
EP
EP
CS[±]
EF
0
0
SDID
0
5
0
0
0
0
Data count
6
0
0
CCAP word1[7:4]
CCAP word1[3:0]
CCAP word2[7:4]
CCAP word2[3:0]
0
0
User data-words
User data-words
User data-words
User data-words
Checksum
7
0
0
0
0
±
0
0
0
0
9
0
0
0
0
10
CS[7]
CS[6]
CS[5]
CS[4]
CS[3]
CS[2]
CS[1]
CS[0]
Table 160. PAL CCAP Data, Full-Byte Mode
Byte
D[9]
D[8]
D[7]
D[6]
D[5]
D[4]
D[3]
D[2]
D[1]
0
D[0]
Description
0
0
0
0
0
1
1
1
0
0
0
1
1
0
1
0
0
1
1
0
0
0
0
1
1
0
1
0
0
1
1
0
0
1
0
Fixed preamble
Fixed preamble
Fixed preamble
DID
1
1
1
1
1
1
2
1
1
1
1
1
3
0
1
0
0
0
4
!EP
!EP
EP
EP
EF
0
0
0
SDID
5
0
0
Data count
6
CCAP word1[7:0]
CCAP word2[7:0]
0
0
User data-words
User data-words
UDW padding 200h
UDW padding 200h
Checksum
7
0
0
±
1
0
0
0
0
0
0
0
0
0
9
1
0
0
0
0
0
0
0
0
0
10
!CS[±]
CS[±]
CS[7]
CS[6]
CS[5]
CS[4]
CS[3]
CS[2]
CS[1]
CS[0]
Rev. A | Page 60 of 104
ADV7189
GDECEL[15:0] Gemstar Decoding Even Lines (SDP),
Address 0x48, [7:0]; Address 0x49, [7:0]
GDECAD Gemstar Decode Ancillary Data Format (SDP),
Address 0x4C, [0]
The 16 bits of the GDECEL[15:0] are interpreted as a collection
of 16 individual line decode enable signals. Each bit refers to a
line of video in an even field. Setting the bit enables the decoder
block trying to find Gemstar or closed caption compatible data
on that particular line. Setting the bit to 0 prevents the decoder
from trying to retrieve data. See Table 164 and Table 165.
The decoded data from Gemstar compatible transmissions or
closed caption is inserted into the horizontal blanking period of
the respective line of video. There is a potential problem if the
retrieved data bytes have the value 0x00 or 0xFF. In an ITU-R
BT.656 compatible data stream, those values are reserved and
used only to form a fixed preamble.
Notes
The GDECAD bit allows the data to be inserted into the
horizontal blanking period in two ways:
•
To retrieve closed caption data services on NTSC (line
284), GDECEL[11] must be set.
•
•
Insert all data straight into the data stream, even the
reserved values of 0x00 and 0xFF, if they occur. This may
violate the output data format specification ITU-R
BT.1364.
•
To retrieve closed caption data services on PAL (line 335),
GDECEL[14] must be set.
Table 161. GDECEL Function
GDECEL[15:0] Description
0x0000*
Split all data into nibbles and insert the half-bytes over
double the number of cycles in a 4-bit format.
Do not attempt to decode Gemstar compatible
data or CCAP on any line (even field).
Table 163. GDECAD Function
*Default value.
GDECAD
Description
0*
1
Split data into half-bytes and insert.
Output data straight in ±-bit format.
GDECOL[15:0] Gemstar Decoding Odd Lines (SDP),
Address 0x4A, [7:0]; Address 0x4B, [7:0]
*Default value.
The 16 bits of the GDECOL[15:0] form a collection of 16
individual line decode enable signals. See Table 164 and
Table 165.
Notes
•
To retrieve closed caption data services on NTSC (line 21),
GDECOL[11] must be set.
•
To retrieve closed caption data services on PAL (line 22),
GDECOL[14] must be set.
Table 162. GDECOL Function
GDECOL[15:0] Description
0x0000*
Do not attempt to decode Gemstar
compatible data or CCAP on any line (odd
field).
*Default value.
Rev. A | Page 61 of 104
ADV7189
Table 164. NTSC Line Enable Bits and Corresponding Line
Table 165. PAL Line Enable Bits and Corresponding Line
Numbering
Numbering
Line Number
(ITU-R BT.470)
Line Number
line[3:0] (ITU-R BT.470)
line[3:0]
Enable Bit
GDECOL[0]
GDECOL[1]
GDECOL[2]
GDECOL[3]
GDECOL[4]
GDECOL[5]
GDECOL[6]
GDECOL[7]
GDECOL[±]
GDECOL[9]
GDECOL[10]
GDECOL[11]
Comment
Gemstar
Gemstar
Gemstar
Gemstar
Gemstar
Gemstar
Gemstar
Gemstar
Gemstar
Gemstar
Gemstar
Enable Bit
GDECOL[0]
GDECOL[1]
GDECOL[2]
GDECOL[3]
GDECOL[4]
GDECOL[5]
GDECOL[6]
GDECOL[7]
GDECOL[±]
GDECOL[9]
GDECOL[10]
GDECOL[11]
GDECOL[12]
GDECOL[13]
GDECOL[14]
GDECOL[15]
GDECEL[0]
GDECEL[1]
GDECEL[2]
GDECEL[3]
GDECEL[4]
GDECEL[5]
GDECEL[6]
GDECEL[7]
GDECEL[±]
GDECEL[9]
GDECEL[10]
GDECEL[11]
GDECEL[12]
GDECEL[13]
GDECEL[14]
GDECEL[15]
Comment
Not valid
Not valid
Not valid
Not valid
Not valid
Not valid
Not valid
Not valid
Not valid
Not valid
Not valid
Not valid
Not valid
Not valid
Closed caption
Not valid
Not valid
Not valid
Not valid
Not valid
Not valid
Not valid
Not valid
Not valid
Not valid
Not valid
Not valid
Not valid
Not valid
Not valid
Closed caption
Not valid
0
1
2
3
4
5
6
7
±
9
10
11
10
11
12
13
14
15
16
17
1±
19
20
21
12
13
14
15
0
1
2
3
4
5
6
7
±
±
9
10
11
12
13
14
15
16
17
1±
19
20
21
22
23
321 (±)
322 (9)
323 (10)
324 (11)
325 (12)
326 (13)
327 (14)
32± (15)
329 (16)
330 (17)
331 (1±)
332 (19)
333 (20)
334 (21)
335 (22)
336 (23)
Gemstar or
closed caption
12
13
14
15
0
1
2
3
4
5
6
7
±
9
10
11
22
23
24
25
GDECOL[12]
GDECOL[13]
GDECOL[14]
GDECOL[15]
GDECEL[0]
GDECEL[1]
GDECEL[2]
GDECEL[3]
GDECEL[4]
GDECEL[5]
GDECEL[6]
GDECEL[7]
GDECEL[±]
GDECEL[9]
GDECEL[10]
GDECEL[11]
Gemstar
Gemstar
Gemstar
Gemstar
Gemstar
Gemstar
Gemstar
Gemstar
Gemstar
Gemstar
Gemstar
Gemstar
Gemstar
Gemstar
Gemstar
9
10
11
12
13
14
15
0
1
2
3
4
5
6
7
±
9
10
11
273 (10)
274 (11)
275 (12)
276 (13)
277 (14)
27± (15)
279 (16)
2±0 (17)
2±1 (1±)
2±2 (19)
2±3 (20)
2±4 (21)
Gemstar or
closed caption
Gemstar
Gemstar
Gemstar
Gemstar
12
13
14
15
2±5 (22)
2±6 (23)
2±7 (24)
2±± (25)
GDECEL[12]
GDECEL[13]
GDECEL[14]
GDECEL[15]
Rev. A | Page 62 of 104
ADV7189
PIXEL PORT CONFIGURATION
The ADV7189 has a very flexible pixel port that can be config-
ured in a variety of formats to accommodate downstream ICs.
Table 168 and Table 169 summarize the various functions that
the ADV7189’s pins can have in different modes of operation.
SWPC Swap Pixel Cr/Cb (SDP), Address 0x27, [7]
This bit allows Cr and Cb samples of the SDP block to be
swapped.
Table 166. SWPC Function
The ordering of components (e.g., Cr versus Cb, CHA/B/C) can
be changed. Refer to the SWPC Swap Pixel Cr/Cb (SDP),
Address 0x27, [7] section. Table 168 indicates the default
positions for the Cr/Cb components.
SWPC
Description
0*
No swapping.
1
Swap Cr and Cb values.
*Default value.
OF_SEL[3:0] Output Format Selection, Address 0x03, [5:2]
LLC1 Output Selection, LLC_PAD_SEL[2:0] (SDP),
Address 0x8F, [6:4]
The following I2C write allows the user to select between the
LLC1 (nominally at 27 MHz) and LLC2 (nominally at
13.5 MHz).
There are several modes in which the ADV7189 pixel port can
be configured. These modes are under the control of
OF_SEL[3:0]. See Table 169 for more details.
The default LLC frequency output on the LLC1 pin is approxi-
mately 27 MHz. For modes that operate with a nominal data
rate of 13.5 MHz (0001, 0010), the clock frequency on the LLC1
pin stays at the higher rate of 27 MHz. For information on
outputting the nominal 13.5 MHz clock on the LLC1 pin, see
the LLC1 Output Selection, LLC_PAD_SEL[2:0] (SDP),
Address 0x8F, [6:4] section.
The LLC2 signal is useful for LLC2 compatible wide bus
(16-/20-bit) output modes. See OF_SEL[3:0] for additional
information. The LLC2 signal and data on the data bus are
synchronized. By default, the rising edge of LLC1/LLC2 is
aligned with the Y data; the falling edge occurs when the data
bus holds C data. The polarity of the clock, and therefore the
Y/C assignments to the clock edges, can be altered by using the
Polarity LLC pin.
Table 167. LLC_PAD_SEL Function
LLC_PAD_SEL[2:0] Description
000*
101
Output nominal 27 MHz LLC on LLC1 pin
Output nominal 13.5 MHz LLC on LLC1 pin
*Default value.
Table 168. P19–P0 Output/Input Pin Mapping
Data Port Pins P[19:0]
19 18 17 16 15 14 13 12 11 10
YCrCb[7:0]OUT
YCrCb[9:0]OUT
Y[7:0]OUT
Y[9:0]OUT
Processor, Format, and Mode
9
8
7
6
5
4
3
2
1
0
SDP
Video Out, ±-Bit, 4:2:2
Video Out, 10-Bit, 4:2:2
Video Out, 16-Bit, 4:2:2
Video Out, 20-Bit, 4:2:2
SDP
SDP
SDP
CrCb[7:0] OUT
CrCb[9:0] OUT
Table 169. Standard Definition Pixel Port Modes
Pixel Port Pins P[19:0]
Function
P[19:10]
P[11:10]
YCrCb[1:0]
P9[9:0]
OF_SEL[3:0]
0000
Format
P[19:12]
YCrCb[9:2]
Y[9:2]
P[9:2]
P[1:0]
10-Bit @ LLC1 4:2:2
20-Bit @ LLC2 4:2:2
16-Bit @ LLC2 4:2:2
±-Bit @ LLC1 4:2:2
Reserved
Three-State
CrCb[9:2]
CrCb[7:0]
Three-State
Three-State
CrCb[1:0]
0001
Y[1:0]
0010
Y[7:0]
Three-State
Three-State
Three-State
Three-State
0011*
YCrCb[7:0]
0110-1111
*Default value.
Reserved. Do not use.
Rev. A | Page 63 of 104
ADV7189
MPU PORT DESCRIPTION
condition and the correct transmitted address. The R/W bit
determines the direction of the data. Logic 0 on the LSB of the
first byte means the master will write information to the
peripheral. Logic 1 on the LSB of the first byte means the master
will read information from the peripheral.
The ADV7189 supports a 2-wire (I2C compatible) serial inter-
face. Four inputs, serial data (SDA1 and SDA2) and serial clock
(SCLK1 and SCLK2), carry information between the ADV7189
and the system I2C master controller. Each slave device is recog-
nized by a unique address. The ADV7189 has two ports: the
control port, which allows the user to set up and configure the
decoder; and the VBI data readback port, which allows the user
to read back captured VBI data. Both the control and VBI ports
have four possible slave addresses for both read and write oper-
ations, depending on the logic level on the ALSB pin. These four
unique addresses are shown in Table 170. The ADV7189’s ALSB
pin controls Bit 1 of the slave address. By altering the ALSB, it is
possible to control two ADV7189s in an application without
having a conflict with the same slave address. The LSB (Bit 0)
sets either a read or write operation. Logic 1 corresponds to a
read operation; Logic 0 corresponds to a write operation.
The ADV7189 acts as a standard slave device on the bus. The
data on the SDA pin is eight bits long, supporting the 7-bit
addresses plus the R/W bit. The ADV7189 has 196 subaddresses
to enable access to the internal registers. It therefore interprets
the first byte as the device address and the second byte as the
starting subaddress. The subaddresses auto-increment, allowing
data to be written to or read from the starting subaddress. A
data transfer is always terminated by a Stop condition. The user
can also access any unique subaddress register on a one-by-one
basis without having to update all the registers.
Stop and Start conditions can be detected at any stage during
the data transfer. If these conditions are asserted out of
sequence with normal read and write operations, they cause an
immediate jump to the idle condition. During a given SCLK
high period, the user should only issue one Start condition, one
Stop condition, or a single Stop condition followed by a single
Start condition. If an invalid subaddress is issued by the user,
the ADV7189 will not issue an acknowledge and will return to
the idle condition.
Table 170. I2C Address for ADV7189
Slave Address
Control Port
Slave Address
VBI Port
ALSB
R/W
0
0
1
1
0
1
0
1
0x40
0x41
0x42
0x43
0x20
0x21
0x22
0x23
To control the device on the bus, a specific protocol must be
followed. First, the master initiates a data transfer by establish-
ing a Start condition, which is defined by a high-to-low
If in auto-increment mode the user exceeds the highest
subaddress, the following action is taken:
transition on SDA1/SDA2 while SCLK1/SCLK2 remains high.
This indicates that an address/data stream will follow. All per-
ipherals respond to the Start condition and shift the next eight
bits (7-bit address + R/W bit). The bits are transferred from
MSB down to LSB. The peripheral that recognizes the trans-
mitted address responds by pulling the data line low during the
ninth clock pulse; this is known as an acknowledge bit. All other
devices withdraw from the bus at this point and maintain an
idle condition. The idle condition is where the device monitors
the SDA1/SDA2 and SCLK1/SCLK2 lines, waiting for the Start
1. In read mode, the highest subaddress register contents
continue to be output until the master device issues a no-
acknowledge. This indicates the end of a read. A no-
acknowledge condition is when the SDA line is not pulled
low on the ninth pulse.
2. In write mode, the data for the invalid byte is not loaded
into any subaddress register, a no acknowledge is issued by
the ADV7189, and the part returns to the idle condition.
SDATA
SCLOCK
S
P
1–7
8
9
1–7
8
9
1–7
DATA
8
9
START ADDR R/W ACK SUBADDRESS ACK
ACK
STOP
Figure 36. Bus Data Transfer
WRITE
S
S
SLAVE ADDR A(S) SUB ADDR
LSB = 0
A(S)
DATA
A(S)
DATA
A(S) P
SEQUENCE
LSB = 1
READ
SEQUENCE
SLAVE ADDR A(S) SUB ADDR
A(S)
S
SLAVE ADDR A(S)
DATA
A(M)
DATA
A(M) P
S = START BIT
P = STOP BIT
A(S) = ACKNOWLEDGE BY SLAVE
A(M) = ACKNOWLEDGE BY MASTER
A(S) = NO-ACKNOWLEDGE BY SLAVE
A(M) = NO-ACKNOWLEDGE BY MASTER
Figure 37. Read and Write Sequence
Rev. A | Page 64 of 104
ADV7189
REGISTER ACCESSES
I2C SEQUENCER
An I2C sequencer is employed in cases where a parameter
exceeds eight bits, and is therefore distributed over two or more
I2C registers (e.g., HSB [11:0]).
The MPU can write to or read from all of the ADV7189’s
registers, except the Subaddress register, which is write-only.
The Subaddress register determines which register the next read
or write operation accesses. All communications with the part
through the bus start with an access to the Subaddress register.
Then, a read/write operation is performed from/to the target
address, which then increments to the next address until a Stop
command on the bus is performed.
When such a parameter is changed using two or more I2C write
operations, the parameter may hold an invalid value for the
time between the first I2C finishing and the last I2C being
completed. In other words, the top bits of the parameter may
already hold the new value while the remaining bits of the
parameter still hold the previous value.
REGISTER PROGRAMMING
The following tables describe each register in terms of its
configuration. The Communications register is an 8-bit, write-
only register. After the part has been accessed over the bus and a
read/write operation is selected, the subaddress is set up. The
Subaddress register determines to/from which register the
operation takes place. Table 172 lists the various operations
under the control of the Subaddress register for the control port.
To avoid this problem, the I2C sequencer holds the already
updated bits of the parameter in local memory; all bits of the
parameter are updated together once the last register write
operation has completed.
The correct operation of the I2C sequencer relies on the
following:
All I2C registers for the parameter in question must be
written to in order of ascending addresses. (e.g., for
HSB[10:0], write to Address 34h first, followed by 35h).
Table 173 lists the various readback registers under the control
of the Subaddress register for the VBI port.
•
Register Select (SR7-SR0)
No other I2C taking place between the two (or more) I2C
writes for the sequence (e.g., for HSB[10:0], write to
Address 0x34 first, immediately followed by 0x35).
These bits are set up to point to the required starting address.
•
Rev. A | Page 65 of 104
ADV7189
I2C CONTROL REGISTER MAP
Table 171. Control Port Register Map Details
Subaddress
Hex
00
Register Name
Reset Value rw
rw 74
Subaddress
Register Name
Input Control
Reset Value rw
Hex
4A
4B
4C
4D
4E
0000 0000
1100 1000
0000 0100
0000 1100
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
0
1
2
3
4
5
6
7
±
9
Gemstar Ctrl 3
Gemstar Ctrl 4
GemStar Ctrl 5
CTI DNR Ctrl 1
CTI DNR Ctrl 2
Reserved
0000 0000
0000 0000
xxxx xxx0
1110 1111
0000 1000
xxxx xxxx
0000 1000
1010 0100
xxxx xxxx
0000 0000
0000 0000
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
0001 1100
xxxx xxxx
xxxx xxxx
0xxx xxxx
xxxx xxxx
1010 1100
0100 1100
0000 0000
0000 0000
0001 0100
1000 0000
1000 0000
1000 0000
1000 0000
0010 0101
0000 0100
0110 0011
0110 0101
0001 0100
0110 0011
Video Selection
Video Selection 2
Output Control
01
rw 75
rw 76
rw 77
rw 7±
rw 79
rw ±0
rw ±1
02
03
Extended Output Control 0101 0101
04
Reserved
0000 0000
0000 0010
0111 1111
1000 0000
1000 0000
0000 0000
0000 0000
0011 0110
0111 1100
0000 0101
0000 0000
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
0001 0010
0100 xxxx
xxxx xxxx
0000 0001
1001 0011
1111 0001
xxxx xxxx
0101 1000
xxxx xxxx
1110 0011
1010 1110
1111 0100
0000 0000
1111 xxxx
xxxx xxxx
0001 0010
0100 0001
1000 0100
0000 0000
0000 0010
0000 0000
0000 0001
1000 0000
1100 0000
0001 0000
xxxx xxxx
0100 0011
0101 0000
00000000
0000 0000
05
4F
Reserved
06
CTI DNR Ctrl 4
Lock Count
Reserved
50
Autodetect Enable
Contrast
07
51
0±
rw ±2–142
52–±E
±F
Reserved
09
Free Run Line Length 1
Free Run Line Length 2
VBI Info
w
w
r
143
144
144
145
146
147
14±
149
150
151
152
153
154
155
156
157
Brightness
rw 10
rw 11
rw 12
rw 13
rw 14
rw 15
0A
0B
90
Hue
90
Default Value Y
Default Value C
ADI Control
0C
WSS 1
r
91
0D
0E
WSS 2
r
92
EDTV 1
r
93
Power Management
Status 1
0F
EDTV 2
r
94
r
r
r
r
16
17
1±
19
10
EDTV 3
r
95
Ident
11
CGMS 1
r
96
Status 2
12
CGMS 2
r
97
Status 3
13
CGMS 3
r
9±
Analog Clamp Control
Digital Clamp Control 1
Reserved
rw 20
rw 21
rw 22
rw 23
rw 24
rw 25
14
CCAP 1
r
99
15
CCAP 2
r
9A
9B
9C
9D
16
Letterbox 1
Letterbox 2
Letterbox 3
Reserved
r
Shaping Filter Control
Shaping Filter Control 2
Comb Filter Control
Reserved
17
r
1±
r
19
rw 15±-177 9E–B1
17± B2
rw 179–194 B2–C2
rw 26–3±
rw 39
rw 40
rw 43
rw 44
rw 45
rw 46
rw 47
rw 4±
rw 49
rw 50
51
1A–26
27
CRC Enable
Reserved
w
Pixel Delay Control
Reserved
2±–2A
2B
ADC Switch 1
ADC Switch 2
Reserved
rw 195
rw 196
C3
C4
Misc Gain Control
AGC Mode Control
Chroma Gain Control 1
Chroma Gain Control 2
Luma Gain Control 1
Luma Gain Control 2
VSync Field Control 1
VSync Field Control 2
VSync Field Control 3
HSync Position Control 1
HSync Position Control 2
HSync Position Control 3
Polarity
2C
rw 197–219 C5–DB
2D
Letterbox Control 1
Letterbox Control 2
Reserved
rw 220
rw 221
rw 222
rw 223
rw 224
rw 225
rw 226
rw 227
rw 22±
rw 225
rw 226
rw 227
rw 225
rw 226
rw 227
DC
DD
DE
DF
E0
E1
E2
E3
E4
E5
E6
E7
E±
E9
EA
2E
2F
30
Reserved
31
Reserved
32
SD Offset Cb
SD Offset Cr
SD Saturation Cb
SD Saturation Cr
NTSC V Bit Begin
NTSC V Bit End
NTSC F Bit Toggle
PAL V Bit Begin
PAL V Bit End
PAL F Bit Toggle
33
rw 52
rw 53
rw 54
rw 55
rw 56
rw 57
rw 5±
rw 59–60
rw 61
rw 62–70
rw 72
rw 73
34
35
36
37
NTSC Comb Control
PAL Comb Control
ADC Control
3±
39
3A
Reserved
3B–3C
3D
Manual Window Control
Reserved
3E–47
4±
Gemstar Ctrl 1
Gemstar Ctrl 2
49
Rev. A | Page 66 of 104
ADV7189
Table 172. Control Port Register Map Bit Details
Register Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Input Control
VID_SEL.3
VID_SEL.2
ENHSPLL
VID_SEL.1
BETACAM
VID_SEL.0
INSEL.3
ENVSPROC
INSEL.2
INSEL.1
INSEL.0
Video Selection
Video Selection 2
Output Control
YPM.2
YPM.1
YPM.0
VBI_EN
TOD
OF_SEL.3
DR_STR.1
OF_SEL.2
DR_STR.0
OF_SEL.1
TIM_OE
OF_SEL.0
BL_C_VBI
SD_DUP_AV
RANGE
Extended Output
Control
BT656-4
EN_SFL_PI
Reserved
Reserved
Autodetect Enable
Contrast
AD_SEC525_EN
CON.7
AD_SECAM_EN
CON.6
AD_N443_EN
CON.5
AD_P60_EN
CON.4
AD_PALN_EN
CON.3
AD_PALM_EN
CON.2
AD_NTSC_EN
CON.1
AD_PAL_EN
CON.0
Reserved
Brightness
Hue
BRI.7
BRI.6
BRI.5
BRI.4
BRI.3
BRI.2
BRI.1
BRI.0
HUE.7
HUE.6
HUE.5
HUE.4
HUE.3
HUE.2
HUE.1
HUE.0
Default Value Y
Default Value C
ADI Control
DEF_Y.5
DEF_C.7
DEF_Y.4
DEF_C.6
TRI_LLC
DEF_Y.3
DEF_C.5
DEF_Y.2
DEF_C.4
DEF_Y.1
DEF_C.3
DR_STR_C.1
DEF_Y.0
DEF_C.2
DR_STR_C.0
PDBP
DEF_VAL_AUTO_EN
DEF_C.1
DEF_VAL_EN
DEF_C.0
DR_STR_S.0
DR_STR_S.1
Power
PWRDN
Management
Status 1
Ident
COL_KILL
IDENT.7
AD_RESULT.2
IDENT.6
AD_RESULT.1
IDENT.5
AD_RESULT.0
IDENT.4
FOLLOW_PW
IDENT.3
FSC_LOCK
IDENT.2
LOST_LOCK
IDENT.1
IN_LOCK
IDENT.0
Status 2
Status 3
FSC NSTD
LL NSTD
MV AGC DET
MV PS DET
MVCS T3
MVCS DET
INST_HLOC K
PAL SW LOCK
INTERLACE
DCT.1
STD FLD LEN
FREE_RUN_ACT
CCLEN
Analog Clamp
Control
Digital Clamp
Control 1
DCT.0
Reserved
Shaping Filter
Control
CSFM.2
CSFM.1
CSFM.0
YSFM.4
YSFM.3
YSFM.2
YSFM.1
YSFM.0
Shaping Filter
Control 2
WYSFMOVR
WYSFM.4
WYSFM.3
NSFSEL.1
WYSFM.2
NSFSEL.0
WYSFM.1
PSFSEL.1
WYSFM.0
PSFSEL.0
Comb Filter Control
Reserved
Pixel Delay Control
SWPC
AUTO_PDC
_EN
CTA.2
CTA.1
CTA.0
LTA.1
LTA.0
Reserved
Misc Gain Control
AGC Mode Control
CKE
PW_UPD
CAGC.0
CMG.±
LAGC.2
CAGT.0
LAGC.1
CMG.5
LAGC.0
CMG.4
CAGC.1
CMG.9
Chroma Gain
Control 1
CAGT.1
CMG.7
LAGT.1
LMG.7
CMG.11
CMG.3
LMG.11
LMG.3
CMG.10
CMG.2
LMG.10
LMG.2
Chroma Gain
Control 2
CMG.6
LGAT.0
LMG.6
CMG.1
LMG.9
LMG.1
CMG.0
LMG.±
LMG.0
Luma Gain
Control 1
Luma Gain
Control 2
LMG.5
LMG.4
VSync Field
Control 1
NEWAVMODE
HVSTIM
VSync Field
Control 2
VSBHO
VSEHO
VSBHE
VSEHE
HSB.10
HSB.6
HSE.6
VSync Field
Control 3
HSync Position
Control 1
HSB.9
HSB.5
HSE.5
HSB.±
HSB.4
HSE.4
HSE.10
HSB.2
HSE.2
HSE.9
HSB.1
HSE.1
HSE.±
HSB.0
HSE.0
HSync Position
Control 2
HSB.7
HSE.7
HSB.3
HSE.3
HSync Position
Control 3
Polarity
PHS
PVS
PF
PCLK
NTSC Comb Control
PAL Comb Control
ADC Control
Reserved
CTAPSN.1
CTAPSP.1
CTAPSN.0
CTAPSP.0
CCMN.2
CCMP.2
CCMN.1
CCMP.1
CCMN.0
CCMP.0
YCMN.2
YCMN.1
YCMN.0
YCMP.0
YCMP.2
YCMP.1
PWRDN_AD C_0
PWRDN_AD C_1
PWRDN_ADC_2
Manual Window
Control
CKILLTHR.2
CKILLTHR.1
CKILLTHR.0
Rev. A | Page 67 of 104
ADV7189
Register Name
Reserved
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Gemstar Ctrl 1
Gemstar Ctrl 2
Gemstar Ctrl 3
Gemstar Ctrl 4
Gemstar Ctrl 5
CTI DNR Ctrl 1
CTI DNR Ctrl 2
Reserved
GDECEL.15
GDECEL.7
GDECOL.15
GDECOL.7
GDECEL.14
GDECEL.6
GDECOL.14
GDECOL.6
GDECEL.13
GDECEL.5
GDECOL.13
GDECOL.5
GDECEL.12
GDECEL.4
GDECOL.12
GDECOL.4
GDECEL.11
GDECEL.3
GDECOL.11
GDECOL.3
GDECEL.10
GDECEL.2
GDECOL.10
GDECOL.2
GDECEL.9
GDECEL.1
GDECOL.9
GDECOL.1
GDECEL.±
GDECEL.0
GDECOL.±
GDECOL.0
GDECAD
CTI_EN
DNR_EN
CTI_AB.1
CTI_AB.0
CTI_AB_EN
CTI_C_TH.1
CTI_C_TH.7
CTI_C_TH.6
CTI_C_TH.5
CTI_C_TH.4
CTI_C_TH.3
CTI_C_TH.2
CTI_C_TH.0
CTI DNR Ctrl 4
Lock Count
DNR_TH.7
FSCLE
DNR_TH.6
SRLS
DNR_TH.5
COL.2
DNR_TH.4
COL.1
DNR_TH.3
COL.0
DNR_TH.2
CIL.2
DNR_TH.1
CIL.1
DNR_TH.0
CIL.0
Reserved
Free Run Line
Length 1
LLC_PAD_SEL.2
LLC_PAD_SEL.1
LLC_PAD_SEL.0
Free Run Line
Length 2
VBI Info
CGMSD
EDTVD
CCAPD
WSSD
WSS 1
WSS1.7
WSS1.6
WSS1.5
WSS1.4
WSS1.3
WSS1.2
WSS1.1
WSS1.0
WSS 2
WSS2.7
WSS2.6
WSS2.5
WSS2.4
WSS2.3
WSS2.2
WSS2.1
WSS2.0
EDTV 1
EDTV1.7
EDTV2.7
EDTV3.7
CGMS1.7
CGMS2.7
CGMS3.7
CCAP1.7
CCAP2.7
LB_LCT.7
LB_LCM.7
LB_LCB.7
EDTV1.6
EDTV2.6
EDTV3.6
CGMS1.6
CGMS2.6
CGMS3.6
CCAP1.6
CCAP2.6
LB_LCT.6
LB_LCM.6
LB_LCB.6
EDTV1.5
EDTV2.5
EDTV3.5
CGMS1.5
CGMS2.5
CGMS3.5
CCAP1.5
CCAP2.5
LB_LCT.5
LB_LCM.5
LB_LCB.5
EDTV1.4
EDTV2.4
EDTV3.4
CGMS1.4
CGMS2.4
CGMS3.4
CCAP1.4
CCAP2.4
LB_LCT.4
LB_LCM.4
LB_LCB.4
EDTV1.3
EDTV2.3
EDTV3.3
CGMS1.3
CGMS2.3
CGMS3.3
CCAP1.3
CCAP2.3
LB_LCT.3
LB_LCM.3
LB_LCB.3
EDTV1.2
EDTV2.2
EDTV3.2
CGMS1.2
CGMS2.2
CGMS3.2
CCAP1.2
CCAP2.2
LB_LCT.2
LB_LCM.2
LB_LCB.2
EDTV1.1
EDTV2.1
EDTV3.1
CGMS1.1
CGMS2.1
CGMS3.1
CCAP1.1
CCAP2.1
LB_LCT.1
LB_LCM.1
LB_LCB.1
EDTV1.0
EDTV2.0
EDTV3.0
CGMS1.0
CGMS2.0
CGMS3.0
CCAP1.0
CCAP2.0
LB_LCT.0
LB_LCM.0
LB_LCB.0
EDTV 2
EDTV 3
CGMS 1
CGMS 2
CGMS 3
CCAP 1
CCAP 2
Letterbox 1
Letterbox 2
Letterbox 3
Reserved
CRC Enable
Reserved
CRC_ENABLE
ADC Switch 1
ADC Switch 2
Reserved
ADC1_SW.3
ADC1_SW.2
LB_SL.2
ADC1_SW.1
LB_SL.1
ADC1_SW.0
ADC0_SW.3
ADC2_SW.3
ADC0_SW.2
ADC2_SW.2
ADC0_SW.1
ADC2_SW.1
ADC0_SW.0
ADC2_SW.0
ADC_SW_M AN
Letterbox Control 1
Letterbox Control 2
Reserved
LB_TH.4
LB_SL.0
LB_TH.3
LB_EL.3
LB_TH.2
LB_EL.2
LB_TH.1
LB_EL.1
LB_TH.0
LB_EL.0
LB_SL.3
Reserved
Reserved
SD Offset Cb
SD Offset Cr
SD Saturation Cb
SD Saturation Cr
NTSC V Bit Begin
NTSC V Bit End
NTSC F Bit Toggle
PAL V Bit Begin
PAL V Bit End
PAL F Bit Toggle
SD_OFF_CB.7
SD_OFF_CR.7
SD_SAT_CB.7
SD_SAT_CR.7
NVBEGDEL O
NVENDDEL O
NFTOGDEL O
PVBEGDEL O
PVENDDEL O
PFTOGDEL O
SD_OFF_CB.6
SD_OFF_CR.6
SD_SAT_CB.6
SD_SAT_CR.6
NVBEGDEL E
NVENDDEL E
NFTOGDEL E
PVBEGDEL E
PVENDDEL E
PFTOGDEL E
SD_OFF_CB.5
SD_OFF_CR.5
SD_SAT_CB.5
SD_SAT_CR.5
NVBEGSIGN
NVENDSIGN
NFTOGSIGN
PVBEGSIGN
PVENDSIGN
PFTOGSIGN
SD_OFF_CB.4
SD_OFF_CR.4
SD_SAT_CB.4
SD_SAT_CR.4
NVBEG.4
SD_OFF_CB.3
SD_OFF_CR.3
SD_SAT_CB.3
SD_SAT_CR.3
NVBEG.3
SD_OFF_CB.2
SD_OFF_CR.2
SD_SAT_CB.2
SD_SAT_CR.2
NVBEG.2
SD_OFF_CB.1
SD_OFF_CR .1
SD_SAT_CB.1
SD_SAT_CR.1
NVBEG.1
SD_OFF_CB.0
SD_OFF_CR.0
SD_SAT_CB.0
SD_SAT_CR.0
NVBEG.0
NVEND.4
NVEND.3
NVEND.2
NVEND.1
NVEND.0
NFTOG.4
NFTOG.3
NFTOG.2
NFTOG.1
NFTOG.0
PVBEG.4
PVBEG.3
PVBEG.2
PVBEG.1
PVBEG.0
PVEND.4
PVEND.3
PVEND.2
PVEND.1
PVEND.0
PFTOG.4
PFTOG.3
PFTOG.2
PFTOG.1
PFTOG.0
Rev. A | Page 6± of 104
ADV7189
Table 173. VBI Port Register Map Details
Register
Name
Reset
Value
rw Subaddress
7
6
5
4
3
2
1
0
VBI Info
WSS 1
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
r
r
r
r
r
r
r
r
r
r
r
0
1
2
3
4
5
6
7
±
9
10
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
0x0±
0x09
0x0A
CGMSD
WSS1.3
WSS2.3
EDTV1.3
EDTV2.3
EDTV3.3
EDTVD
WSS1.2
WSS2.2
EDTV1.2
EDTV2.2
EDTV3.2
CCAPD
WSS1.1
WSS2.1
EDTV1.1
EDTV2.1
EDTV3.1
WSSD
WSS1.7
WSS2.7
EDTV1.7
EDTV2.7
EDTV3.7
WSS1.6
WSS2.6
EDTV1.6
EDTV2.6
EDTV3.6
WSS1.5
WSS2.5
EDTV1.5
EDTV2.5
EDTV3.5
WSS1.4
WSS2.4
EDTV1.4
EDTV2.4
EDTV3.4
WSS1.0
WSS2.0
EDTV1.0
EDTV2.0
EDTV3.0
WSS 2
EDTV 1
EDTV 2
EDTV 3
CGMS 1
CGMS 2
CGMS 3
CCAP 1
CCAP 2
CGMS1.7 CGMS1.6 CGMS1.5 CGMS1.4 CGMS1.3 CGMS1.2 CGMS1.1 CGMS1.0
CGMS2.7 CGMS2.6 CGMS2.5 CGMS2.4 CGMS2.3 CGMS2.2 CGMS2.1 CGMS2.0
CGMS3.7 CGMS3.6 CGMS3.5 CGMS3.4 CGMS3.3 CGMS3.2 CGMS3.1 CGMS3.0
CCAP1.7 CCAP1.6 CCAP1.5 CCAP1.4 CCAP1.3 CCAP1.2 CCAP1.1 CCAP1.0
CCAP2.7 CCAP2.6 CCAP2.5 CCAP2.4 CCAP2.3 CCAP2.2 CCAP2.1 CCAP2.0
Rev. A | Page 69 of 104
ADV7189
I2C REGISTER MAP DETAILS
Table 174. Register 0x00
Bit
Subaddress Register
Bit Description
Register Setting
Comments
7
6
5
4
3
2
1
0
0x00
Input
Control
INSEL [3:0]. The INSEL bits allow the
user to select an input channel as
well as the input format.
0
0
0
0
0
0
0
0
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
0
0
1
1
0
0
0
1
0
1
0
1
0
1
0
1
CVBS in on AIN1
CVBS in on AIN2
CVBS in on AIN3
CVBS in on AIN4
CVBS in on AIN5
CVBS in on AIN6
Y on AIN1, C on AIN4
Y on AIN2, C on AIN5
Y on AIN3, C on AIN6
Composite
S-Video
YPbPr
Y on AIN1, Pr on AIN4, Pb on
AIN5
1
0
1
0
Y on AIN2, Pr on AIN3, Pb on
AIN6
1
1
1
1
1
0
1
1
1
1
1
0
0
1
1
1
0
1
0
1
CVBS in on AIN7
CVBS in on AIN±
CVBS in on AIN9
CVBS in on AIN10
CVBS in on AIN11
Composite
0
0
0
0
0
0
0
0
0
0
1
1
0
1
0
1
Auto-detect PAL (BGHID),
NTSC (without pedestal)
VID_SEL [3:0]. The VID_SEL bits
allow the user to select the input
video standard.
Auto-detect PAL (BGHID),
NTSC (M) (with pedestal)
Auto-detect PAL (N), NTSC
(M) (without pedestal)
Auto-detect PAL (N), NTSC
(M) (with pedestal)
0
0
0
0
1
1
1
1
1
1
0
0
0
0
1
1
0
0
0
1
0
1
0
1
NTSC(J)
NTSC(M)
PAL 60
NTSC 4.43
PAL BGHID
PAL N (BGHID without
pedestal)
1
1
1
1
1
1
0
0
1
1
1
1
1
1
0
0
1
1
0
1
0
1
0
1
PAL M (without pedestal)
PAL M
PAL combination N
PAL combination N
SECAM (with pedestal)
SECAM (with pedestal)
Note: Grayed out sections mark the reset value of the register
Rev. A | Page 70 of 104
ADV7189
Table 175. Register 0x01
Bit
Subaddress Register Bit Description
Register Setting
Comments
7
6
5
4
3
2
1
0
0x01
Video
Selection
Reserved
0
0
0
Set to default
ENVSPROC
0
1
Disable VSync processor
Enable VSync processor
Reserved
BETACAM
0
Set to default
0
1
Standard video input
Betacam input enable
ENHSPLL
Reserved
0
1
Disable HSync processor SECAM standard. YPrPb through SDP.
Enable HSync processor
1
Set to default
Table 176. Register 0x02
Bit
Register
Setting
Subaddress Register
Bit Description
Comments
7
6
5
4
3
2
1
0
0x02
Video
Enhancement
Used to enhance the picture
and improve contrast.
YPM [2:0]. Y Peaking Filter
mode. This function allows
Control
the user to boost/ attenuate
luma signals around the
color subcarrier frequency.
0
0
0
0
1
0
0
1
1
0
0
1
0
1
0
C = +4.5 dB,
S = +9.25 dB
C = Composite (2.6 MHz),
S = S-Video (3.75 MHz).
C = +4.5 dB,
S = +9.25 dB
C = +4.5 dB,
S = +5.75 dB
C = +1.25 dB,
S = +3.3 dB
No Change.
C = +0 dB,
S = +0 dB
1
1
1
0
1
1
1
0
1
C = –1.25 dB,
S = –3 dB
C = –1.75 dB,
S = –± dB
C = –3.0 dB,
S = –± dB
Reserved.
0
0
0
0
0
Set to default
Rev. A | Page 71 of 104
ADV7189
Table 177. Register 0x03
Bit
Subaddress Register
Bit Description
Register Setting
Comments
7
6
5
4
3
2
1
0
0x03
Output
Control
SD_DUP_AV. Duplicates the AV
codes from the Luma into the
chroma path.
0
AV codes to suit
±-/10-bit interleaved
data output
1
AV codes duplicated
(for 16-/20-bit
interfaces)
Reserved.
0
Set as default
OF_SEL [3:0]. Allows the user to
choose from a set of output
formats.
0
0
0
0
0
0
0
1
10-bit @ LLC1 4:2:2
ITU-R BT.656
20-bit @
27 MHz/13.5MHz 4:2:2
0
0
1
0
1
1
0
1
16-bit @ LLC1 4:2:2
±-bit @ LLC1 4:2:2
ITU-R BT.656
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
See also TIM_OE
(Table 17±;
TRI_LLC
TOD. Three-State Output Drivers.
This bit allows the user to three-
state the output drivers: P[19:0],
HS, VS, FIELD, and SFL.
(Table 1±0).
0
1
Output pins enabled
Drivers three-stated
VBI_EN. Allows VBI data (Lines 1 to
21) to be passed through with only
a minimum amount of filtering
performed.
0
1
All lines filtered and
scaled
Only active video
region filtered
Rev. A | Page 72 of 104
ADV7189
Table 178. Register 0x04
Bit
Register
Setting
Subaddress Register
Bit Description
Comments
7
6
5
4
3
2
1
0
0x04
Extended
Output
Control
RANGE. Allows the user to select
the range of output values. Can
be BT656 compliant, or can fill the
whole accessible number range.
0
1
16 < Y < 235,
16 < C < 240
ITU-R BT.656.
1 < Y < 254,
1 < C < 254
Extended Range.
EN_SFL_PIN.
SFL output enables
encoder and decoder to
be connected directly.
0
1
SFL output is
disabled
SFL information
output on the
SFL pin
During VBI.
BL_C_VBI. Blank Chroma during
VBI. If set, enables data in the VBI
region to be passed through the
decoder undistorted.
0
1
Decode and
output color
Blank Cr and Cb
Controlled by TOD.
TIM_OE. Timing signals output
enable.
0
1
HS, VS, F three-
stated
HS, VS, F forced
active
Recommended.
DR_STR[1:0]. Drive strength of
output drivers can be increased or
decreased for EMC or crosstalk
reasons.
0
0
1
0
1
0
Low drive, 1×
Medium-low, 2×
Medium-high,
3×
1
1
High drive, 4×
Reserved.
1
Set to default
BT656-4. Allows the user to select
an output mode compatible with
ITU- R BT656-3/4.
0
1
BT656-3
compatible
BT656-4
compatible
Rev. A | Page 73 of 104
ADV7189
Table 179. Register 0x07 and 0x08
Bit
Register
Setting
Subaddress
Register
Bit Description
Comments
7
6
5
4
3
2
1
0
0x07
Autodetect
Enable
AD_PAL_EN. PAL B/G/I/H autodetect
enable.
0
1
Disable
Enable
AD_NTSC_EN. NTSC autodetect enable.
AD_PALM_EN. PAL M autodetect enable.
AD_PALN_EN. PAL N autodetect enable.
AD_P60_EN. PAL 60 autodetect enable.
AD_N443_EN. NTSC443 autodetect enable.
AD_SECAM_EN. SECAM autodetect enable.
0
1
Disable
Enable
0
1
Disable
Enable
0
1
Disable
Enable
0
1
Disable
Enable
0
1
Disable
Enable
0
1
Disable
Enable
AD_SEC525_EN. SECAM 525 autodetect
enable.
0
1
Disable
Enable
0x0±
Contrast
Register
0x00 Gain = 0;
0x±0 Gain = 1;
0xFF Gain = 2.
CON[7:0]. Contrast adjust. This is the user
control for contrast adjustment.
1
0
0
0
0
0
0
0
Luma gain = 1
Rev. A | Page 74 of 104
ADV7189
Table 180. Register 0x09 to 0x0E
Subaddress Register Bit Description
Bit
7
1
0
6
0
0
5
0
0
4
0
0
3
0
0
2
0
0
1
0
0
0
0
0
Register Setting
Comments
0x09
Reserved
(Saturation)
Reserved.
0x0A
Brightness
Register
0x00 = 0IRE
0x7F = 100IRE
0xFF = –100IRE.
BRI[7:0]. This register controls
the brightness of the video
signal.
0x0B
0x0C
Hue Register
Hue range =
–90° to +90°.
HUE[7:0]. This register
contains the value for the color
hue adjustment.
0
0
0
0
0
0
0
0
0
1
Default Value Y
DEF_VAL_EN. Default value
enable.
Free Run mode
dependent on
DEF_VAL_AUTO_EN
Force SDP Free Run
mode on and output
blue screen
DEF_VAL_AUTO_EN. Default
value.
0
1
Disable SDP Free Run
mode
When lock is lost,
Free Run mode
can be enabled
to output stable
timing, clock,
Enable Automatic Free
Run mode (blue
screen)
and a set color.
Default Y value
output in free-
run mode.
DEF_Y[5:0]. Default value Y.
This register holds the Y
default value.
0
0
0
1
1
1
1
1
0
1
1
1
Y[7:0] = {DEF_Y[5:0],
0, 0, 0, 0}
0x0D
0x0E
Default Value C
ADI Control
Cr[7:0] = {DEF_C[7:4],
0, 0, 0, 0, 0, 0}
Cb[7:0] = {DEF_C[3:0],
Default Cb/Cr
value output in
Free Run mode.
Default values
give blue screen
output.
DEF_C[7:0] Default value C. Cr
and Cb default values are
defined in this register.
0, 0, 0, 0, 0, 0}
0
0
0
0
DR_STR_S[1:0]. Select the
drive strength of the sync
signals. HS, VS, and F can be
increased or decreased for
EMC or crosstalk reasons.
Low drive strength
(1×)
0
1
1
1
0
1
Medium-low (2×)
Medium-high (3×)
High drive strength
(4×)
DR_STR_C[1:0]. Select the
strength of the clock signal
output driver. Can be
increased or decreased for
EMC or crosstalk reasons.
0
0
Low drive strength
(1×)
0
1
1
1
0
1
Medium-low (2×)
Medium-high (3×)
High drive strength
(4×)
Reserved.
0
0
Set as default
LLC pin active
See TOD,
(Table 177)
TIM_OE
TRI_LLC. Enables the LLC pin
to be three-stated.
0
1
(Table 17±).
LLC pin drivers three-
stated
Reserved.
0
Set as default
Rev. A | Page 75 of 104
ADV7189
Table 181. Register 0x0F to 0x11
Bit
Subaddress Register
Bit Description
7
6
5
4
3
2
1
0
Register Setting
Comments
0x0F
Power
Management
Reserved
0
0
Set to default
PDBP. Power-down bit
priority selects between
PWRDN bit or PIN.
0
1
Chip power-down
controlled by pin
Bit has priority (pin
disregarded)
Reserved
0
0
Set to default
PWRDN. Power-down
places the decoder in a full
power-down mode.
0
1
System functional
Powered down
See PDBP,
Register 0x0F, Bit 2.
Reserved
0
Set to default
0
1
Normal operation
Executing reset
takes approx. 2 ms.
This bit is self-
clearing.
RES. Chip Reset will load all
I2C bits with default values.
Start reset sequence
0x10
Status Register
Read-Only
STATUS_1[7:0]. Provides
information about the
internal status of the
decoder.
STATUS_1[3:0]
x
In lock (right now) = 1
x
Lost lock (since last
read)
x
Fsc lock (right now) = 1
x
Peak white AGC mode
active = 1
STATUS_1[6:4]
AD_RESULT[2:0].
Autodetection result
reports the findings
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
NTSM-MJ
NTSC-443
PAL-M
Detected standard.
PAL-60
PAL-BGHID
SECAM
PAL combination N
SECAM 525
STATUS_1[7] COL_KILL.
Color Kill.
x
x
Color kill is active = 1
0x11
Info Register
Read-Only
IDENT[7:0]. Provides
identification on the
revision of the part.
x
x
x
x
x
x
x
Rev. A | Page 76 of 104
ADV7189
Table 182. Register 0x12 to 0x13
Bit
Subaddress Register
Bit Description
7
6
5
4
3
2
1
0
Register Setting
Comments
0x12
Status Register 2
Read-only
STATUS_2[7:0]. Provides
information about the internal status
of the decoder.
STATUS_2[5:0].
x
MV color striping
detected
1 = Detected.
x
MV color striping
type
0 = Type 2,
1 = Type 3.
x
MV pseudosync
detected
1 = Detected.
1 = Detected.
1 = Detected.
1 = Detected.
x
MV AGC pulses
detected
x
Nonstandard line
length
x
Fsc frequency
nonstandard
Reserved
x
x
x
0x13
Status Register 3
Read only
STATUS_3[7:0]. Provides
information about the internal status
of the decoder.
x
1 = Horizontal
lock achieved
Unfiltered.
x
x
x
1 = Reserved bits
No function.
x
1 = Free Run
mode active
Blue screen
output.
1 = Field length
standard
x
1 = Swinging
burst detected
Reliable
sequence.
Table 183. Register 0x14
Bit
Subaddress Register
Bit Description
7
6
5
4
3
2
1
0
Register Setting
0x14
Analog Clamp
Control
Reserved.
0
0
1
0
Reserved. Set to default.
CCLEN. Current clamp enable allows the user to
switch off the current sources in the analog front.
0
1
I sources switched off.
I sources enabled.
Reserved.
Reserved.
0
Reserved set to default.
Reserved set to default.
0
0
Table 184. Register 0x15
Bit
Subaddress Register
Bit Description
7
6
5
4
3
2
1
0
Register Setting
0x15
Digital Clamp
Control 1
Reserved
x
x
x
x
x
Set to default.
DCT[1:0]. Digital clamp timing determines the
time constant of the digital fine clamp circuitry.
0
0
1
1
0
1
0
1
Slow (TC = 1 s).
Medium (TC = 0.5 s).
Fast (TC = 0.1 s).
TC dependant on video.
Reserved
0
Set to default.
Rev. A | Page 77 of 104
ADV7189
Table 185. Register 0x17
Bit
Subaddress Register
Bit Description
Register Setting
Comments
7
6
5
4
3
2
1
0
0x17
Shaping
Filter
Control
Decoder selects
optimum Y shaping
filter depending on
CVBS quality.
YSFM[4:0]. Selects Y
Shaping Filter mode
when in CVBS only
mode. Allows the user to
select a wide range of
low-pass and notch
filters.
If either automode is
selected, the decoder
selects the optimum Y
filter depending on the
CVBS video source
0
0
0
0
0
Auto wide notch for poor
quality sources or wide-
band filter with Comb for
good quality input
0
0
0
0
1
Auto narrow notch for poor
quality sources or wideband
filter with comb for good
quality input
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
SVHS 1
If one of these modes is
selected, the decoder
does not change filter
modes depending on
video quality. A fixed
filter response (the one
selected) is used for
good and bad quality
video.
SVHS 2
quality (good vs. bad).
SVHS 3
SVHS 4
SVHS 5
SVHS 6
SVHS 7
SVHS ±
SVHS 9
SVHS 10
SVHS 11
SVHS 12
SVHS 13
SVHS 14
SVHS 15
SVHS 16
SVHS 17
SVHS 1± (CCIR601)
PAL NN1
PAL NN2
PAL NN3
PAL WN 1
PAL WN 2
NTSC NN1
NTSC NN2
NTSC NN3
NTSC WN1
NTSC WN2
NTSC WN3
Reserved
Automatically selects a
C filter based on video
standard and quality.
CSFM[2:0]. C shaping
filter mode allows the
selection from a range of
low-pass chrominance
filters.
If either automode is
selected, the decoder
selects the optimum C
filter depending on the
CVBS video source
quality (good vs. bad).
Nonauto settings force a
C filter for all standards
and quality of CVBS
video.
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
Auto selection 1.5 MHz
Auto selection 2.17 MHz
SH1
Selects a C filter for all
video standards and for
good and bad video.
SH2
SH3
SH4
SH5
Wideband mode
Rev. A | Page 7± of 104
ADV7189
Table 186. Register 0x18 to 0x19
Subaddress Register Bit Description
Bit
7
6
5
4
3
2
1
0
Comments
0x1±
Shaping
Filter
Control 2
WYSFM[4:0] Wideband Y Shaping Filter Mode allows
the user to select which Y shaping filter is used for the Y
component of Y/C, YPbPr, B/W input signals; it is also
used when a good quality input CVBS signal is
detected. For all other inputs, the Y shaping filter
chosen is controlled by YSFM[4:0].
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
Reserved. Do not use.
Reserved. Do not use.
SVHS 1
SVHS 2
SVHS 3
SVHS 4
SVHS 5
SVHS 6
SVHS 7
SVHS ±
SVHS 9
SVHS 10
SVHS 11
SVHS 12
SVHS 13
SVHS 14
SVHS 15
SVHS 16
SVHS 17
SVHS 1± (CCIR 601)
Reserved. Do not use.
Reserved. Do not use.
Reserved. Do not use.
1
1
1
1
1
Reserved.
0
0
Set to default.
WYSFMOVR. Enables the use of the automatic WYSFN
filter.
0
1
Manual select filter
using WYSFM[4:0].
Auto selection of best
filter.
0x19
Comb
Filter
PSFSEL[1:0]. Controls the signal bandwidth that is fed
to the comb filters (PAL).
0
0
1
1
0
1
0
1
Narrow.
Medium.
Wide.
Control
Widest.
NSFSEL[1:0]. Controls the signal bandwidth that is fed
to the comb filters (NTSC).
0
0
1
1
0
1
0
1
Narrow.
Medium.
Medium.
Wide.
Reserved.
1
1
1
1
Set as default.
Rev. A | Page 79 of 104
ADV7189
Table 187. Register 0x27 to 0x2A
Bit
Subaddress Register
Bit Description
7
6
5
4
3
2
1
0
Comments
Notes
0x27
Pixel
Delay
Control
CVBS mode
LTA[1:0]. Luma timing adjust
allows the user to specify a
timing difference between
chroma and luma samples.
LTA[1:0] = 00b;
S-Video mode
LTA[1:0]= 01b,
YPrPb mode
0
0
1
0
0
1
0
1
No Delay
Luma 1 clk (37 ns) delayed
Luma 2 clk (72 ns) early
Luma 1 clk (37 ns) early
LTA[1:0] = 01b.
Reserved.
0
Set to 0
CVBS mode
CTA[2:0]. Chroma timing
adjust allows a specified
timing difference between the
CTA[2:0] = 011b,
S-Video mode
CTA[2:0] = 101b,
YPrPb mode
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
Not valid setting
Chroma + 2 pixels (early)
Chroma + 1 pixel (early)
No Delay
luma and chroma samples.
CTA[2:0] = 110b.
Chroma – 1 pixel (late)
Chroma – 2 pixels (late)
Chroma – 3 pixels (late)
Not a valid setting
AUTO_PDC_EN.
Automatically programs the
LTA/CTA values so that luma
and chroma are aligned at the
output for all modes of
operation.
0
1
Use values in LTA[1:0] and
CTA[2:0] for delaying
luma/chroma
LTA and CTA values
determined automatically
SWPC. Allows the Cr and Cb
samples to be swapped.
0
1
No swapping
Swap the Cr and Cb
Rev. A | Page ±0 of 104
ADV7189
Table 188. Register 0x2B to 0x2C
Subaddress Register Bit Description
Bit
7
6
5
4
3
2
1
0
Comments
Notes
0x2B
Misc Gain
Control
PW_UPD. Peak white update
determines the rate of gain.
0
1
Update once per
video line.
Peak white must be
enabled. See LAGC[2:0].
Update once per
field.
Reserved.
0
1
1
0
1
0
1
0
Set to default.
For SECAM color kill,
threshold is set at ±%.
CKE. Color kill enable allows
the color kill function to be
switched on and off.
0
1
Color kill disabled.
Color kill enabled.
See CKILLTHR[2:0]
(Table 196).
Reserved.
1
Set to default.
0x2C
AGC Mode
Control
CAGC[1:0]. Chroma automatic
gain control selects the basic
mode of operation for the AGC
in the chroma path.
0
0
0
1
Manual fixed gain.
Use CMG[11:0].
Use luma gain for
chroma.
1
1
0
1
Automatic gain.
Based on color burst.
Freeze chroma
gain.
Reserved.
1
1
Set to 1.
LAGC[2:0]. Luma automatic
gain control selects the mode
of operation for the gain
control in the luma path.
0
0
0
0
0
1
Manual fixed gain.
Use LMG[11:0].
AGC no override
through white
peak. Man IRE
control.
Blank level to sync tip.
0
0
1
1
1
0
0
1
0
AGC auto-override
through white
peak. Man IRE
control.
Blank level to sync tip.
Blank level to sync tip.
Blank level to sync tip.
AGC no override
through white
peak. Auto IRE
control.
AGC auto-override
through white
peak. Auto IRE
control.
1
1
1
0
1
1
1
0
1
AGC active video
with white peak.
AGC active video
with average video.
Freeze gain.
Reserved.
1
Set to 1.
Rev. A | Page ±1 of 104
ADV7189
Table 189. Register 0x2D to 0x30
Bit
Subaddress Register
Bit Description
7
6
5
4
3
2
1
0
Comments
Notes
0x2D
Chroma
Gain
Control 1
CAGC[1:0] settings
decide in which
mode CMG[11:0]
operates.
CMG[11:8]. Chroma manual
gain can be used to program a
desired manual chroma gain.
Reading back from this register
in AGC mode gives the current
gain.
0
1
0
0
Reserved.
1
1
Set to 1.
Has an effect only if
CAGC[1:0] is set to
auto gain (10).
CAGT[1:0]. Chroma automatic
gain timing allows adjustment of
the chroma AGC tracking speed.
0
0
1
1
0
1
0
1
Slow (TC = 2 s).
Medium (TC = 1 s).
Fast (TC = 0.2 s).
Adaptive.
0x2E
0x2F
Chroma
Gain
Control 2
CMG[11:0] = 750d;
gain is 1 in NTSC
CMG[11:0] = 741d;
gain is 1 in PAL.
Min value is 0dec
(G = –60 dB)
Max value is 3750
(Gain = 5).
CMG[7:0]. Chroma manual gain
lower ± bits. See CMG[11:±] for
description.
0
0
0
1
0
1
0
x
0
x
0
x
0
x
Luma Gain
Control 1
LAGC[1:0] settings
decide in which
mode LMG[11:0]
operates.
LMG[11:8]. Luma manual gain
can be used program a desired
manual chroma gain, or to read
back the actual gain value used.
Reserved.
Set to 1.
Only has an effect if
AGC[1:0] is set to
auto gain (001, 010,
011,or 100).
LAGT[1:0]. Luma automatic gain
timing allows adjustment of the
luma AGC tracking speed.
0
0
1
1
0
1
0
1
Slow (TC = 2 s).
Medium (TC = 1 s).
Fast (TC = 0.2 s).
Adaptive
0x30
Luma Gain
Control 2
LMG[11:0] =
1234dec; gain is 1 in NTSC 1024 (G = 0.±5)
NTSC LMG[11:0] =
1266dec; gain is 1 in
PAL.
Min value
LMG[7:0]. Luma manual gain
can be used to program a
desired manual chroma gain or
read back the actual used gain
value.
PAL (G = 0.±1).
Max value
NTSC 246± (G = 2),
PAL = 2532 (G = 2).
x
x
x
x
x
x
x
x
Rev. A | Page ±2 of 104
ADV7189
Table 190. Register 0x31
Bit
Subaddress Register
Bit Description
7
6
5
4
3
2
1
0
Comments
Notes
0x31
VS and
FIELD
Reserved.
0
1
0
Set to default
Control 1
HVSTIM. Selects where
within a line of video the VS
signal is asserted.
0
1
Start of line relative to HSE
Start of line relative to HSB
HSE = Hsync end
HSB = Hsync begin
NEWAVMODE. Sets the
EAV/SAV mode.
0
1
EAV/SAV codes generated
to suit ADI encoders
Manual VS/Field position
controlled by registers
0x32, 0x33, and 0xE5–0xEA
Reserved.
0
0
0
Set to default
Table 191. Register 0x32 to 0x33
Subaddress Register Bit Description
Bit
7
6
5
4
3
2
1
0
Comments
Notes
0x32
VSync Field
Control 2
Reserved.
0
0
0
0
0
1
Set to default.
VSBHE.
NEWAVMODE bit must
be set high.
0
1
VS goes high in the middle of
the line (even field).
VS changes state at the start of
the line (even field).
VSBHO.
0
1
VS goes high in the middle of
the line (odd field).
VS changes state at the start of
the line (odd field).
0x33
VSync Field
Control 3
Reserved.
0
0
0
1
0
0
Set to default.
VSEHE.
NEWAVMODE bit must
be set high.
0
1
VS goes low in the middle of the
line (even field).
VS changes state at the start of
the line (even field).
VSEHO.
0
1
VS goes low in the middle of the
line (odd field).
VS changes state at the start of
the line odd field.
Rev. A | Page ±3 of 104
ADV7189
Table 192. Register 0x34 to 0x36
Bit
Subaddress Register
Bit Description
7
6
5
4
3
2
1
0
Comments
Notes
0x34
HS Position
Control 1
HS output ends
HSE[10:0] pixels
after the falling edge the position and
Using HSB and HSE
the user can program
HSE[10:8]. HS end allows the
positioning of the HS output
within the video line.
0
0
0
of HSync.
length of the output
HSync.
Reserved.
0
Set to 0.
HS output starts
HSB[10:0] pixels
after the falling edge
of HSync.
HSB[10:8]. HS begin allows
the positioning of the HS
output within the video line.
0
0
0
Reserved.
0
0
Set to 0.
0x35
0x36
HS Position
Control 2
HSB[7:0] See above, using
HSB[9:0] and HSE[9:0] the user
can program the position and
length of HS output signal.
0
0
0
0
0
0
0
0
0
0
1
0
0
0
HS Position
Control 3
HSE[7:0] See above.
0
Table 193. Register 0x37
Bit
Subaddress
Register
Bit Description
7
6
5
4
3
2
1
0
Comment
0x37
Polarity
PCLK. Sets the polarity of LLC1.
0
1
Invert polarity.
Normal polarity as per Timing Diagrams.
Reserved.
0
0
Set to 0.
PF. Sets the FIELD polarity.
0
1
Active high.
Active low.
Reserved.
0
Set to 0.
PVS. Sets the VS polarity.
0
1
Active high.
Active low.
Reserved.
0
Set to 0.
PHS. Sets HS polarity.
0
1
Active high.
Active low.
Rev. A | Page ±4 of 104
ADV7189
Table 194. Register 0x38
Bit
Subaddress Register
Bit Description
7
6
5
4
3
2
1
0
Comments
Notes
0x3±
NTSC Comb
Control
YCMN[2:0]. Luma
Comb Mode, NTSC.
0
0
0
Adaptive 3-line, 3-tap
luma.
1
1
0
0
0
1
Use low-pass notch.
Fixed luma comb
(2-line).
Top lines of memory.
All lines of memory.
1
1
1
1
0
1
Fixed luma comb
(3-Line).
Fixed luma comb
(2-line).
Bottom lines of memory.
CCMN[2:0]. Chroma
Comb Mode, NTSC.
0
0
0
3-line adaptive for
CTAPSN = 01.
4-line adaptive for
CTAPSN = 10.
5-line adaptive for
CTAPSN = 11.
1
1
0
0
0
1
Disable chroma comb
Fixed 2-line for
CTAPSN = 01.
Top lines of memory.
All lines of memory.
Fixed 3-line for
CTAPSN = 10.
Fixed 4-line for
CTAPSN = 11.
1
1
1
1
0
1
Fixed 3-line for
CTAPSN = 01.
Fixed 4-line for
CTAPSN = 10.
Fixed 5-line for
CTAPSN = 11.
Fixed 2-line for
CTAPSN = 01.
Bottom lines of memory.
Fixed 3-line for
CTAPSN = 10.
Fixed 4-line for
CTAPSN = 11.
CTAPSN[1:0].
Chroma
Comb Taps, NTSC.
0
0
1
1
0
1
0
1
Adapts 3 lines – 2 lines.
Not used.
Adapts 5 lines – 3 lines.
Adapts 5 lines – 4 lines.
Rev. A | Page ±5 of 104
ADV7189
Table 195. Register 0x39 to 0x3A
Bit
Subaddress Register
Bit Description
7
6
5
4
3
2
1
0
Comments
Notes
0x39
PAL Comb
Control
YCMP[2:0]. Luma Comb
mode, PAL.
0
1
1
0
0
1
0
0
0
Adaptive 5-line, 3-tap luma comb.
Use low-pass notch.
Fixed luma comb.
Top lines of
memory.
1
1
1
1
0
1
Fixed luma comb (5-line).
Fixed luma comb (3-line).
All lines of
memory.
Bottom lines
of memory.
CCMP[2:0]. Chroma
Comb mode, PAL.
0
0
0
3-line adaptive for CTAPSN = 01
4-line adaptive for CTAPSN = 10
5-line adaptive for CTAPSN = 11.
1
1
0
0
0
1
Disable chroma comb.
Fixed 2-line for CTAPSN = 01.
Top lines of
memory.
Fixed 3-line for CTAPSN = 10.
Fixed 4-line for CTAPSN = 11.
Fixed 3-line for CTAPSN = 01.
1
1
1
1
0
1
All lines of
memory.
Fixed 4-line for CTAPSN = 10.
Fixed 5-line for CTAPSN = 11.
Fixed 2-line for CTAPSN = 01.
Bottom lines
of memory.
Fixed 3-line for CTAPSN = 10.
Fixed 4-line for CTAPSN = 11.
CTAPSP[1:0]. Chroma
comb taps, PAL.
0
0
1
1
0
1
0
1
Adapts 5-lines – 2 lines (2 taps).
Not used.
Adapts 5 lines – 3 lines (3 taps).
Adapts 5 lines – 4 lines (4 taps).
0x3A
Reserved.
0
Set as default.
PWRDN_ADC_2. Enables
power-down of ADC2.
0
1
ADC2 normal operation.
Power down ADC2.
PWRDN_ADC_1. Enables
power-down of ADC1.
0
1
ADC1 normal operation.
Power down ADC1.
PWRDN_ADC_0. Enables
power-down of ADC0.
0
1
ADC0 normal operation.
Power down ADC0.
Reserved.
0
0
0
1
Set as default.
Rev. A | Page ±6 of 104
ADV7189
Table 196. Register 0x3D
Bit
Subaddress Register
Bit Description
7
6
5
4
3
2
1
0
Comments
Notes
0x3D
Manual
Window
Reserved.
0
0
1
1
Set to default.
CKILLTHR[2:0].
CKE = 1 enables the color kill function and
must be enabled for CKILLTHR[2:0] to take
effect.
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
Kill at 0.5%.
Kill at 1.5%.
Kill at 2.5%.
Kill at 4%.
Kill at ±.5%.
Kill at 16%.
Kill at 32%.
Reserved.
Reserved.
0
Set to default.
Table 197. Registers 0x41 to 0x4C
Subaddress Register Bit Description
Bit
7
6
5
4
3
2
1
0
Comments
Set to default.
Notes
0x41
Resample
Control
Reserved.
0
1
0
0
0
0
SFL_INV. Controls the
behavior of the PAL switch
bit.
0
1
SFL compatible with
ADV7190/ADV7191/ADV7194
encoders.
SFL compatible with
ADV717x/ADV7173x encoders.
Reserved.
0
Set to default.
0x4±
Gemstar
Control 1
LSB = Line 10,
MSB = Line 25,
Default = Do not
check for
GDECEL[15:0]. 16
individual enable bits that
select the lines of video
(even field lines 10–25)
that the decoder checks
for Gemstar compatible
data.
Gemstar
compatible data
on any lines [10–
25] in even fields.
GDECEL[15:8]. See above.
GDECEL[7:0]. See above.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0x49
0x4A
Gemstar
Control 2
Gemstar
Control 3
LSB= Line 10,
MSB= Line 25,
Default = Do not
check for
GDECOL[15:0]. 16
individual enable bits that
select the lines of video
(odd field lines 10–25) that
the decoder checks for
Gemstar compatible data.
Gemstar
compatible data
on any lines [10–
25] in odd fields.
GDECOL[15:8]. See above.
GDECOL[7:0]. See above.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0x4B
0x4C
Gemstar
Control 4
Gemstar
Control 5
GDECAD. Controls the
manner in which decoded
Gemstar data is inserted
into the horizontal
0
1
Split data into half byte.
To avoid 00/FF
code.
Output in straight ±-bit format.
blanking period.
Reserved.
x
x
x
x
x
x
x
Undefined.
Rev. A | Page ±7 of 104
ADV7189
Table 198. Registers 0x4D to 0x50
Bit
Subaddress Register
Bit Description
7
6
5
4
3
2
1
0
Comments
0x4D
CTI DNR
Control 1
CTI_EN. CTI enable.
0
1
Disable CTI.
Enable CTI.
CTI_AB_EN. Enables the mixing of the
transient improved chroma with the
original signal.
0
1
Disable CTI alpha blender.
Enable CTI alpha blender.
CTI_AB[1:0]. Controls the behavior of the
alpha-blend circuitry.
0
0
1
1
0
1
0
1
Sharpest mixing.
Sharp mixing.
Smooth.
Smoothest.
Reserved.
0
Set to default.
DNR_EN. Enable or bypass the DNR block.
0
1
Bypass the DNR block.
Enable the DNR block.
Reserved.
Reserved.
1
Set to default.
Set to default.
1
0
0x4E
0x50
CTI DNR
Control 2
CTI_CTH[7:0]. Specifies how big the
amplitude step must be to be steepened
by the CTI block.
0
0
0
0
0
0
1
1
0
0
0
0
0
0
CTI DNR
Control 4
Set to 0x04 for A/V input; set to
0x0A for tuner input.
DNR_TH[7:0]. Specifies the maximum
edge that is interpreted as noise and is
therefore blanked.
0
Rev. A | Page ±± of 104
ADV7189
Table 199. Register 0x51
Bit
Subaddress Register Bit Description
7
6
5
4
3
2
1
0
Comments
Notes
0x51
Lock
Count
Operational only for
SDP modes.
CIL[2:0]. Count-into-lock
determines the number of lines
the system must remain in lock
before showing a locked status.
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
1 line of video
2 lines of video
5 lines of video
10 lines of video
100 lines of video
500 lines of video
1000 lines of video
100000 lines of video
COL[2:0]. Count-out-of-lock
determines the number of lines
the system must remain out-of-
lock before showing a lost-
locked status.
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
1 line of video
2 lines of video
5 lines of video
10 lines of video
100 lines of video
500 lines of video
1000 lines of video
100000 lines of video
SRLS. Select raw lock signal.
Selects the determination of
the lock. status.
0
1
Over field with vertical
info
Line-to-line evaluation
FSCLE. Fsc lock enable.
FSCLE must be set to
0 in YPrPb mode if a
reliable LOST_LOCK
bit is set to 0.
0
1
Lock status set only by
horizontal lock
Lock status set by
horizontal lock and
subcarrier lock.
Rev. A | Page ±9 of 104
ADV7189
Table 200. Registers 0x8F to 0x90
Bit
Subaddress Register
Bit Description
7
6
5
4
3
2
1
0
Comments
Notes
0x±F
Free Run
Line
Reserved.
0
0
0
0
Set to default.
Length 1
LLC_PAD_SEL [2:0]. Enables
manual selection of clock for
LLC1 pin.
0
1
0
0
0
1
LLC1 (nominal 27 MHz)
selected out on LLC1
pin.
LLC2 (nominally
13.5 MHz) selected out
on LLC1 pin.
For 16-bit 4:2:2 out,
OF_SEL[3:0] = 0010.
Reserved.
0
Set to default.
0x90
VBI Info
Read Mode
Details
Ready-only status
bits.
WSSD. Screen signaling
detected.
0
1
No WSS detected.
WSS detected.
CCAPD. Closed caption data.
EDTVD. EDTV sequence.
CGMSD. CGMS sequence.
Reserved.
0
1
No CCAP signals
detected.
CCAP sequence
detected.
0
1
No EDTV sequence
detected.
EDTV sequence
detected.
0
1
No CGMS transition
detected.
CGMS sequence
decoded.
x
x
x
x
Rev. A | Page 90 of 104
ADV7189
Table 201. Registers 0x91 to 0x9D
Subaddress Register Bit Description
Bit
7
6
5
4
3
2
1
0
Comments
Notes
0x91
0x92
0x93
0x94
0x95
0x96
0x97
0x9±
0x99
WSS1[7:0]
WSS2[7:0]
EDTV1[7:0]
EDTV2[7:0]
EDTV3[7:0]
CGMS1[7:0]
CGMS2[7:0]
CGMS3[7:0]
CCAP1[7:0]
WSS1[7:0]. Wide
screen signaling
data. Read-only
register.
x
x
x
x
x
x
x
x
WSS2[7:6] are
undetermined.
WSS1[7:0]. Wide
screen signaling
data. Read-only
register.
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
EDTV1[7:0].
EDTV data
register. Read-
only register.
EDTV2[7:0].
EDTV data
register. Read-
x
x
x
x
x
x
x
x
only register.
EDTV3[7:6] are
undetermined.
EDTV3[5] is reserved for
future use
EDTV3[7:0].
EDTV data
register. Read-
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
only register.
CGMS1[7:0].
CGMS data
register. Read-
only register.
CGMS2[7:0].
CGMS data
register. Read-
x
x
x
x
x
x
x
x
only register.
CGMS3[7:4] are
undetermined.
CGMS3[7:0].
CGMS data
register. Read-
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
only register.
CCAP1[7]contains parity
bit for Byte 0.
CCAP1[7:0].
Closed caption
data register.
Read-only
register.
0x9A
CCAP2[7:0]
CCAP2[7]contains parity
bit for Byte 0.
CCAP2[7:0].
Closed caption
data register.
Read-only
x
x
x
x
x
x
x
x
register.
0x9B
0x9C
LB_LCT[7:0]
LB_LCM[7:0]
Reports the number of
black lines detected at
the top of active video.
This feature examines the
active video at the start and
at the end of each field. It
enables format detection
even if the video is not
accompanied by a CGMS or
WSS sequence.
Letterbox 1.
Read-only
register.
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Reports the number of
black lines detected in
the bottom half of active
video if subtitles are
detected.
Letterbox 2.
Read-only
register.
0x9D
LB_LCB[7:0]
Reports the number of
black lines detected at
the bottom of active
video.
Letterbox 3.
Read-only
register.
x
x
x
x
x
x
x
x
Rev. A | Page 91 of 104
ADV7189
Table 202. Register 0xB2
Bit
Subaddress Register
Bit Description
7
6
5
4
3
2
1
0
Comments
0xB2
CRC Enable
Write Register
Reserved.
0
0
Set as default.
CRC_ENABLE. Enables CRC checksum
decoded from CGMS packet to validate
CGMSD.
0
1
Turn off CRC check.
CGMSD goes high with
valid checksum.
Reserved.
0
0
0
1
1
Set as default.
Table 203. Register 0xC3
Bit
Subaddress Register
Bit Description
7
6
5
4
3
2
1
0
Comment
Note
0xC3
ADC
SWITCH 1
SETADC_sw_man_en = 1.
ADC0_SW[3:0]. Manual muxing
control for ADC0.
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
No connection
AIN1
AIN2
AIN3
AIN4
AIN5
AIN6
No connection
No connection
AIN7
AIN±
AIN9
AIN10
AIN11
AIN12
No connection
ADC1_SW[3:0]. Manual muxing
control for ADC1.
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
No connection
No connection
No connection
AIN3
AIN4
AIN5
AIN6
No connection
No connection
No connection
No connection
AIN9
AIN10
AIN11
AIN12
No connection
Rev. A | Page 92 of 104
ADV7189
Table 204. Register 0xC4
Bit
Subaddress Register
Bit Description
7
6
5
4
3
2
1
0
Comments
Notes
SETADC_sw_man_en = 1
0xC4
ADC
ADC2_SW[3:0]. Manual muxing
SWITCH 2
control for ADC2.
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
No connection
No connection
AIN2
No connection
No connection
AIN5
AIN6
No connection
No connection
No connection
AIN±
No connection
No connection
AIN11
AIN12
No connection
Reserved.
x
x
x
ADC_SW_MAN_EN. Enable manual
setting of the input signal muxing.
0
1
Disable
Enable
Rev. A | Page 93 of 104
ADV7189
Table 205. Registers 0xDC to 0xE4
Bit
Subaddress Register
Bit Description
7
6
5
4
3
2
1
0
Comment
0xDC
Letterbox
Control 1
LB_TH [4:0]. Sets the threshold value that
detects a black.
0
1
1
0
0
Default threshold for detection of
black lines.
Reserved.
1
0
1
Set as default
0xDD
Letterbox
Control 2
LB_EL[3:0]. Programs the end line of the
activity window for LB detection (end of
field).
1
1
0
0
LB detection ends with last line of
active video on a field.
1100: 262/525.
LB_SL[3:0]. Programs the start line of the
activity window for LB detection (start of
field).
0
1
0
0
Letterbox detection aligned with
start of active video.
0100: 23/2±6 NTSC.
0xDE
0xDF
0xE0
0xE1
0xE2
0xE3
Reserved.
Reserved.
Reserved.
0
0
0
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
SD Offset Cb
SD Offset Cr
SD_OFF_CB [7:0]. Adjusts the hue by
selecting the offset for the Cb channel.
SD_OFF_CR [7:0]. Adjusts the hue by
selecting the offset for the Cr channel.
SD
Saturation
Cb
SD_SAT_CB [7:0]. Adjusts the saturation
of the picture by affecting the gain on the
Cb channel.
Chroma gain = 0 dB.
Chroma gain = 0 dB.
0xE4
SD
SD_SAT_CR [7:0]. Adjusts the saturation
of picture by affecting the gain on the Cr
channel.
Saturation Cr
1
0
0
0
0
0
0
0
Rev. A | Page 94 of 104
ADV7189
Table 206. Registers 0xE5 to 0xE7
Subaddress Register Bit Description
Bit
7
6
5
4
3
2
1
0
Comments
0xE5
0xE6
0xE7
NTSC V Bit
Begin
NVBEG[4:0]. How many lines after lCOUNT rollover
to set V high.
0
0
1
0
1
NTSC default (BT.656).
NVBEGSIGN.
0
1
Set to low when manual
programming.
Not suitable for user
programming.
NVBEGDELE. Delay V bit going high by one line
relative to NVBEG (even field).
0
1
No delay.
Additional delay by 1 line.
NVBEGDELO. Delay V bit going high by one line
relative to NVBEG (odd field).
0
1
No delay.
Additional delay by 1 line.
NTSC V Bit
End
NVEND[4:0]. How many lines after lCOUNT rollover
to set V low.
0
0
1
0
0
NTSC default (BT.656).
NVENDSIGN.
0
1
Set to low when manual
programming.
Not suitable for user
programming.
NVENDDELE. Delay V bit going low by one line
relative to NVEND (even field).
0
1
No delay.
Additional delay by 1 line.
NVENDDELO. Delay V bit going low by one line
relative to NVEND (odd field).
0
1
No delay.
Additional delay by 1 line.
NTSC F Bit
Toggle
NFTOG[4:0]. How many lines after lCOUNT rollover
to toggle F signal.
0
0
0
1
1
NTSC default.
NFTOGSIGN.
0
1
Set to low when manual
programming.
Not suitable for user
programming.
NFTOGDELE. Delay F transition by one line
relative to NFTOG (even field).
0
1
No delay.
Additional delay by 1 line.
NFTOGDELO. Delay F transition by one line
relative to NFTOG (odd field).
0
1
No delay.
Additional delay by 1 line.
Rev. A | Page 95 of 104
ADV7189
Table 207. Registers 0xE8 to 0xEA
Bit
Subaddress Register
Bit Description
7
6
5
4
3
2
1
0
Comments
0xE±
0xE9
0xEA
PAL V Bit
Begin
PVBEG[4:0]. How many lines after lCOUNT rollover
to set V high.
0
0
1
0
1
PAL default (BT.656).
PVBEGSIGN.
0
1
Set to low when manual
programming.
Not suitable for user
programming.
PVBEGDELE. Delay V bit going high by one line
relative to PVBEG (even field).
0
1
No delay.
Additional delay by 1 line.
PVBEGDELO. Delay V bit going high by one line
relative to PVBEG (odd field).
0
1
No delay.
Additional delay by 1 line.
PAL V Bit
End
PVEND[4:0]. How many lines after lCOUNT rollover
to set V low.
1
0
1
0
0
PAL default (BT.656).
PVENDSIGN.
0
1
Set to low when manual
programming.
Not suitable for user
programming.
PVENDDELE. Delay V bit going low by one line
relative to PVEND (even field).
0
1
No delay.
Additional delay by 1 line.
PVENDDELO. Delay V bit going low by one line
relative to PVEND (odd field).
0
1
No delay.
Additional delay by 1 line.
PAL F Bit
Toggle
PFTOG[4:0]. How many lines after lCOUNT rollover
to toggle F signal.
0
0
0
1
1
PAL default (BT.656).
PFTOGSIGN.
0
1
Set to low when manual
programming.
Not suitable for user
programming.
PFTOGDELE. Delay F transition by one line
relative to PFTOG (even field).
0
1
No delay.
Additional delay by 1 line.
PFTOGDELO. Delay F transition by one line
relative to PFTOG (odd field).
0
1
No delay.
Additional delay by 1 line.
Rev. A | Page 96 of 104
ADV7189
APPENDIX A
I2C PROGRAMMING EXAMPLES
Mode 1 CVBS Input (Composite Video on AIN5)
All standards are supported through autodetect, 10-bit, 4:2:2, ITU-R BT.656 output on P19–P10.
Table 208. Mode 1 CVBS Input
Register Address
Register Value
Notes
0x00
0x01
0x03
0x17
0x04
0x±±
0x00
0x41
CVBS input on AIN5.
Turn off HSYNC processor (SECAM only13).
Enable 10-bit output on P19–P10.
Set CSFM to SH1.
0x23
0x2B
0x40
0xE2
Optimum color PLL setting.
AGC tweak.
0x3A
0x51
0xD2
0x16
0x24
0x01
Power down ADC 1 and ADC 2.
Turn off FSC detect for IN LOCK status.
AGC tweak.
0xD3
0x01
AGC tweak.
0xDB
0x9B
AGC tweak.
0x0E
0x±5
ADI recommended programming sequence. This sequence must be followed exactly when
setting up the decoder.
0x±9
0x±D
0x±F
0xB5
0xD4
0xD6
0xE2
0xE3
0xE4
0xE±
0x0E
0x0D
0x9B
0x4±
0x±B
0xFB
0x6D
0xAF
0x00
0xB5
0xF3
0x05
Recommended setting.
Recommended setting.
Recommended setting.
Recommended setting.
Recommended setting.
Recommended setting.
Recommended setting.
Recommended setting.
Recommended setting.
Recommended setting.
Recommended setting.
13 For all SECAM modes of operation, HSYNC PROCESSOR must be turned off.
Rev. A | Page 97 of 104
ADV7189
Mode 2 S-Video Input (Y on AIN1 and C on AIN4)
All standards are supported through autodetect, 10-bit, ITU-R BT.656 output on P19–P10.
Table 209. Mode 2 S-Video Input
Register Address
0x00
0x01
0x03
0x2B
Register Value
0x06
0x±±
0x00
0xE2
Notes
Y1 = AIN1, C1 = AIN4.
Turn off HSYNC processor (SECAM only).
Enable 10-bit output on P19–P10.
AGC tweak.
0x3A
0x51
0xD2
0x12
0x24
0x01
Power down ADC 2.
Turn off FSC detect for IN LOCK status.
AGC tweak.
0xD3
0x01
AGC tweak.
0xDB
0x9B
AGC tweak.
0x0E
0x±5
ADI recommended programming sequence. This sequence must be followed exactly when
setting up the decoder.
0xB5
0xD4
0xD6
0xE2
0xE3
0xE4
0xE±
0x0E
0x±B
0xFB
0x6D
0xAF
0x00
0xB5
0xF3
0x05
Recommended setting.
Recommended setting.
Recommended setting.
Recommended setting.
Recommended setting.
Recommended setting.
Recommended setting.
Recommended setting.
Mode 3 YPrPb Input 525i/625i (Y on AIN2, Pr on AIN3, and Pb on AIN6)
All standards are supported through autodetect, 10-bit, ITU-R BT.656 output on P19–P10.
Table 210. Mode 3 YPrPb Input 525i/625i
Register Address Register Value Notes
0x00
0x01
0x03
0x2B
0x3A
0x51
0xD2
0xD3
0xDB
0x0E
0x0A
0x±±
0x00
0xE2
0x10
0x24
0x01
0x01
0x9B
0x±5
Y2 = AIN2, Pr2 = AIN3, Pb2 = AIN6.
Disable HSync PLL.
Enable 10-bit output on P19–P10.
AGC tweak.
Set latch clock.
Turn off FSC detect for IN LOCK status.
AGC tweak.
AGC tweak.
AGC tweak.
ADI recommended programming sequence. This sequence must be followed exactly when setting
up the decoder.
0xD6
0xE±
0x0E
0x6D
0xF3
0x05
Recommended setting.
Recommended setting.
Recommended setting.
Rev. A | Page 9± of 104
ADV7189
Mode 4 CVBS Tuner Input PAL Only on AIN4
10-bit, ITU-R BT.656 output on P19–P10.
Table 211. Mode 4 CVBS Tuner Input PAL Only
Register Address
Register Value
Notes
0x00
0x03
0x07
0x17
0x±3
0x00
0x01
0x41
CVBS AIN4 Force PAL only mode.
Enable 10-bit output on P19–P10.
Enable PAL autodetection only.
Set CSFM to SH1.
0x19
0x2B
0xFA
0xE2
Stronger dot crawl reduction.
AGC tweak.
0x3A
0x50
0x51
0xD2
0x16
0x0A
0x24
0x01
Power down ADC 1 and ADC 2.
Set higher DNR threshold.
Turn off FSC detect for IN LOCK status.
AGC tweak.
0xD3
0x01
AGC tweak.
0xDB
0x9B
AGC tweak.
0x0E
0x±5
ADI recommended programming sequence. This sequence must be followed exactly when
setting up the decoder.
0x±9
0x±D
0x±F
0xB5
0xD4
0xD6
0xE2
0xE3
0xE4
0xE±
0x0E
0x0D
0x9B
0x4±
0x±B
0xFB
0x6D
0xAF
0x00
0xB5
0xF3
0x05
Recommended setting.
Recommended setting.
Recommended setting.
Recommended setting.
Recommended setting.
Recommended setting.
Recommended setting.
Recommended setting.
Recommended setting.
Recommended setting.
Recommended setting.
Rev. A | Page 99 of 104
ADV7189
APPENDIX B
It is also recommended to use a single ground plane for the
entire board. This ground plane should have a spacing gap
between the analog and digital sections of the PCB (see
Figure 39).
PCB LAYOUT RECOMMENDATIONS
The ADV7189 is a high precision, high speed mixed-signal
device. To achieve the maximum performance from the part, it
is important to have a well laid-out PCB board. The following is
a guide for designing a board using the ADV7189.
Analog Interface Inputs
ADV7189
ANALOG
SECTION
DIGITAL
The inputs should receive care when being routed on the PCB.
Track lengths should be kept to a minimum, and 75 Ω trace
impedances should be used when possible. Trace impedances
other than 75 Ω will also increase the chance of reflections.
SECTION
Figure 39. PCB Ground Layout
Power Supply Decoupling
It is recommended to decouple each power supply pin with
0.1 µF and 10 nF capacitors. The fundamental idea is to have a
decoupling capacitor within about 0.5 cm of each power pin.
Also, avoid placing the capacitor on the opposite side of the PC
board from the ADV7189, as doing so interposes resistive vias
in the path. The bypass capacitors should be located between
the power plane and the power pin. Current should flow from
the power plane to the capacitor to the power pin. Do not make
the power connection between the capacitor and the power pin.
Placing a via underneath the 100 nF capacitor pads, down to the
power plane, is generally the best approach (see Figure 38).
Experience has repeatedly shown that the noise performance is
the same or better with a single ground plane. Using multiple
ground planes can be detrimental because each separate ground
plane is smaller, and long ground loops can result.
In some cases, using separate ground planes is unavoidable. For
those cases, it is recommended to at least place a single ground
plane under the ADV7189. The location of the split should be
under the ADV7189. For this case, it is even more important to
place components wisely because the current loops will be
much longer (current takes the path of least resistance). An
example of a current loop: power plane to ADV7189 to digital
output trace to digital data receiver to digital ground plane to
analog ground plane.
VDD
GND
VIA TO SUPPLY
VIA TO GND
10nF
100nF
PLL
Place the PLL loop filter components as close to the ELPF pin as
possible. Do not place any digital or other high frequency traces
near these components. Use the values suggested in the data
sheet with tolerances of 10ꢀ or less.
Figure 38. Recommend Power Supply Decoupling
Digital Outputs (Both Data and Clocks)
It is particularly important to maintain low noise and good
stability of PVDD. Careful attention must be paid to regulation,
filtering, and decoupling. It is highly desirable to provide
separate regulated supplies for each of the analog circuitry
groups (AVDD, DVDD, DVDDIO, and PVDD).
Try to minimize the trace length that the digital outputs have to
drive. Longer traces have higher capacitance, which requires
more current, which causes more internal digital noise. Shorter
traces reduce the possibility of reflections.
Adding a series resistor of a value between 30 Ω and 50 Ω can
suppress reflections, reduce EMI, and reduce the current spikes
inside the ADV7189. If series resistors are used, place them as
close to the ADV7189 pins as possible. However, try not to add
vias or extra length to the output trace to get the resistors closer.
Some graphic controllers use substantially different levels of
power when active (during active picture time) and when idle
(during horizontal and vertical sync periods). This can result in
a measurable change in the voltage supplied to the analog
supply regulator, which can, in turn, produce changes in the
regulated analog supply voltage. This can be mitigated by
regulating the analog supply, or at least PVDD, from a different,
cleaner, power source (for example, from a 12 V supply).
If possible, limit the capacitance that each of the digital outputs
drives to less than 15 pF. This can easily be accomplished by
keeping traces short and by connecting the outputs to only one
device. Loading the outputs with excessive capacitance increases
the current transients inside the ADV7189, creating more
digital noise on its power supplies.
Rev. A | Page 100 of 104
ADV7189
It is essential that the cutoff of this filter be less than 1 Hz to
Digital Inputs
ensure correct operation of the internal clamps within the part.
These clamps ensure that the video stays within the 5 V range of
the op amp used.
The digital inputs on the ADV7189 were designed to work with
3.3 V signals, and are not tolerant of 5 V signals. Extra
components are needed if 5 V logic signals are required to be
applied to the decoder.
0
–20
Antialiasing Filters
For inputs from some video sources that are not bandwidth
limited, signals outside the video band can alias back into the
video band during A/D conversion and appear as noise on the
output video. The ADV7189 oversamples the analog inputs by a
factor of 4. This 54 MHz sampling frequency reduces the
requirement for an input filter; for optimal performance it is
recommended that an antialiasing filter be employed. The
recommended low cost circuit for implementing this buffer and
filter circuit for all analog input signals is shown in Figure 41.
–40
–60
–80
–100
The buffer is a simple emitter-follower using a single npn
transistor. The antialiasing filter is implemented using passive
components. The passive filter is a third-order Butterworth
filter with a –3 dB point of 9 MHz. The frequency response of
the passive filter is shown in Figure 40. The flat pass band up to
6 MHz is essential. The attenuation of the signal at the output of
the filter due to the voltage divider of R24 and R63 is compen-
sated for in the ADV7189 part using the automatic gain control.
The ac coupling capacitor at the input to the buffer creates a
high-pass filter with the biasing resistors for the transistor. This
filter has a cut-off of
–120
100kHz 300kHz 1MHz
3MHz
10MHz 30MHz 100MHz 300MHz 1GHz
FREQUENCY
Figure 40. Third-Order Butterworth Filter Response
{2 × π × (R39||R89) × C93}–1 = 0.62 Hz
Rev. A | Page 101 of 104
ADV7189
APPENDIX C
TYPICAL CIRCUIT CONNECTION
Examples of how to connect the ADV7189 video decoder are shown in Figure 41 and Figure 42.
AVDD_5V
R43
0Ω
BUFFER
R39
4.7kΩ
C93
100µF
C
B
FILTER
IN
Q6
R53
56Ω
L10
12µH
E
R38
75Ω
R89
5.6kΩ
OUT
R24
470Ω
R63
820Ω
C95
22pF
C102
10pF
AGND
Figure 41. ADI Recommended Antialiasing Circuit for All Input Channels
Rev. A | Page 102 of 104
ADV7189
FERITE BEAD
33µF
DVDDIO
(3.3V)
POWER SUPPLY
DECOUPLING FOR
EACH POWER PIN
10µF
0.1µF
0.01µF
DGND
FERITE BEAD
DGND
DGND
DGND
PVDD
(1.8V)
POWER SUPPLY
DECOUPLING FOR
EACH POWER PIN
33µF
10µF
0.1µF
0.01µF
AGND
AGND
AGND
AGND
FERITE BEAD
AVDD
(3.3V)
POWER SUPPLY
DECOUPLING FOR
EACH POWER PIN
33µF
10µF
0.1µF
0.01µF
AGND
AGND
AGND
AGND
FERITE BEAD
DVDD
(1.8V)
POWER SUPPLY
DECOUPLING FOR
EACH POWER PIN
33µF
10µF
0.1µF
0.01µF
AGND DGND
DGND
DGND
DGND
DGND
100nF
100nF
100nF
100nF
100nF
100nF
S-VIDEO
P0
P1
P2
P3
P4
P5
P6
P7
P8
AIN1
AIN7
AIN2
AIN8
AIN3
AIN9
AIN4
AIN10
AIN5
AIN11
AIN6
AIN12
Y
Pr
MULTI
ADV7189
Pb
P9
FORMAT
PIXEL
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
PORT
P19–P10 10-BIT ITU-R BT.656 PIXEL DATA @ 27MHz
P9–P0 Cb AND Cr 20-BIT ITU-R BT.656 PIXEL DATA @ 13.5MHz
P19–P10 Y 20-BIT ITU-R BT.656 PIXEL DATA @ 13.5MHz
CBVS
AGND
AGND
CAP Y1
CAP Y2
+
0.1µF
0.1µF
10µF
0.1µF
0.1µF
1nF
1nF
LLC1
LLC2
27MHz OUTPUT CLOCK
13.5MHz OUTPUT CLOCK
AGND
CAP C1
CAP C2
+
10µF
AGND
OE
OUTPUT ENABLE I/P
CML
+
10µF
0.1µF
10µF
REFOUT
+
0.1µF
SFL
HS
SFL O/P
HS O/P
AGND
33pF
XTAL
27MHz
DVDDIO
VS
VS O/P
XTAL1
FIELD
FIELD O/P
DGND
2
SELECT I C
ADDRESS
33pF
DGND
DVSS
ALSB
DVDDIO DVDDIO
ELPF
1.7kΩ
10nF
2kΩ
2kΩ
100Ω
100Ω
SCLK
SDA
82nF
MPU INTERFACE
CONTROL LINES
PVDD
DVDDIO
4.7kΩ
RESET
RESET
AGND
AGND
DGND
100nF
DGND
DGND
Figure 42. Typical Connection Diagram
Rev. A | Page 103 of 104
ADV7189
OUTLINE DIMENSIONS
16.00
BSC SQ
0.75
0.60
0.45
1.60
MAX
80
61
60
1
SEATING
PLANE
PIN 1
14.00
BSC SQ
TOP VIEW
(PINS DOWN)
10°
6°
2°
1.45
1.40
1.35
0.20
0.09
7°
VIEW A
20
41
3.5°
0°
40
21
0.15
0.05
SEATING
PLANE
0.10 MAX
COPLANARITY
0.65
BSC
0.38
0.32
0.22
VIEW A
ROTATED 90° CCW
COMPLIANT TO JEDEC STANDARDS MS-026-BEC
Figure 43. 80-Lead Low Profile Quad Flat Package [LQFP]
(ST-80-2)
Dimensions shown in millimeters
ORDERING GUIDE
Model
Temperature Range
Package Description
Package Option
ADV71±9KST
EVAL-ADV71±9EBM
–25°C to +70°C
Low Profile Quad Flat Package (LQFP)
Evaluation Board
ST-±0-2
Note: The ADv7189 is a Pb-free environmentally friendly product. It is manufactured using the most up-to-date materials and processes.
The coating on the leads of each device is 100ꢀ pure Sn electroplate. The device is suitable for Pb-free applications, and can withstand
surface-mount soldering at up to 255°C ( 5°C).
In addition, it is backward-compatible with conventional SnPb soldering processes. This means the electroplated Sn coating can be
soldered with Sn/Pb solder pastes at conventional reflow temperatures of 220°C to 235°C.
Purchase of licensed I2C components of Analog Devices or one of its sublicensed Associated Companies conveys a license for the purchaser under the Philips I2C Patent
Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips.
©
2004 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D04819–0–6/04(A)
Rev. A | Page 104 of 104
相关型号:
EVAL-ADV7282MEBZ
10-Bit, 4 Oversampled SDTV Video Decoder with Differential Inputs and Deinterlacer
ADI
©2020 ICPDF网 联系我们和版权申明