EVAL-ADV7282AMEBZ [ADI]
10-Bit, 4x Oversampled SDTV Video Decoder with Differential Inputs;型号: | EVAL-ADV7282AMEBZ |
厂家: | ADI |
描述: | 10-Bit, 4x Oversampled SDTV Video Decoder with Differential Inputs 电视 |
文件: | 总28页 (文件大小:571K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
10-Bit, 4× Oversampled SDTV Video
Decoder with Differential Inputs
Data Sheet
ADV7282A
FEATURES
GENERAL DESCRIPTION
Worldwide NTSC/PAL/SECAM color demodulation support
One 10-bit ADC, 4× oversampling per channel for CVBS, Y/C,
and YPrPb modes
Analog video input channels with on-chip antialiasing filter
ADV7282A: up to 4 input channels
ADV7282A-M: up to 6 input channels
Video input support for CVBS (composite), S-Video (Y/C),
and YPrPb (component)
Fully differential, pseudo differential, and single-ended
CVBS video input support
The ADV7282A1 has the same pinout as and is software
compatible with the ADV7282 with the exception of a updated
IDENT code. The mobile industry processor interface (MIPI®)
model of the ADV7282A (ADV7282A-M) has the same pinout
as and is software compatible with the ADV7282-M with the
exception of an updated IDENT code.
All features, functionality, and specifications are shared by the
ADV7282A and the ADV7282A-M, unless otherwise noted.
The ADV7282A is a versatile one-chip, multiformat video
decoder that automatically detects standard analog baseband
video signals and converts them into YCrCb 4:2:2 component
video data streams.
NTSC/PAL/SECAM autodetection
STB diagnostics on 2 video inputs
Up to 4 V common-mode input range solution
Excellent common-mode noise rejection capabilities
5-line adaptive 2D comb filter and CTI video enhancement
Integrated AGC with adaptive peak white mode
Fast switching capability
Integrated I2P video output converter (deinterlacer)
ACE
The analog input of the ADV7282A features an input mux
(4-channel on ADV7282A, 6-channel on ADV7282A-M), a
single 10-bit analog-to-digital converter (ADC) and an on-chip
differential to single-ended converter to accommodate the
direct connection of differential, pseudo differential, or single-
ended CVBS without the need for external amplifier circuitry.
Downdither (8-bit to 6-bit)
The standard definition processor (SDP) in the ADV7282A
automatically detects PAL, NTSC and SECAM standards in the
form of composite, S-Video (Y/C) and component. The analog
video is converted into a 4:2:2 component video data stream
that is output either via an 8-bit ITU-R BT.656 standard-
compatible interface (ADV7282A) or via a MIPI CSI-2 Tx
(hereafter referred to as MIPI Tx) interface (ADV7282A-M).
The ADV7282A also feature a deinterlacer for interlaced to
progressive (I2P) conversion.
Rovi copy protection detection
8-bit ITU-R BT.656 YCrCb 4:2:2 output and HS, VS, or field
synchronization (ADV7282A)
MIPI CSI-2 output interface (ADV7282A-M only)
Full featured VBI data slicer with WST support
Power-down mode available
2-wire, I2C-compatible serial interface
Qualified for automotive applications
−40°C to +105°C temperature grade
The ADV7282A offers short to battery (STB) diagnostic sense
inputs and general-purpose outputs.
32-lead, 5 mm × 5 mm, RoHS compliant LFCSP
APPLICATIONS
The ADV7282A is provided in a space-saving LFCSP surface-
mount, RoHS compliant package. The ADV7282A is rated over
the −40°C to +105°C temperature range, making it ideal for
automotive applications.
The ADV7282A must be configured in accordance with the I2C
writes provided in the evaluation board script files available at
www.analog.com/ADV7282A.
Advanced driver assistance
Automotive infotainment
DVRs for video security
Media players
1 Protected by U.S. Patent 5,784,120.
Rev. A
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rightsof third parties that may result fromits use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks andregisteredtrademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2017–2018 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADV7282A
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Input Networks ............................................................................... 17
Single-Ended Input Network.................................................... 17
Differential Input Network ....................................................... 17
STB Protection............................................................................ 17
Applications Information .............................................................. 18
Input Configuration................................................................... 18
STB Diagnostics.......................................................................... 18
Programming the STB Diagnostic Function.......................... 19
Adaptive Contrast Enhancement (ACE)................................. 20
I2P Function ................................................................................ 20
ITU-R BT.656 Tx Configuration (ADV7282A Only) ........... 20
MIPI Tx Output (ADV7282A-M Only).................................. 21
I2C Port Description................................................................... 21
Register Maps.................................................................................. 23
PCB Layout Recommendations.................................................... 25
Analog Interface Inputs............................................................. 25
Power Supply Decoupling ......................................................... 25
VREFN and VREFP Pins .......................................................... 25
Digital Outputs ........................................................................... 25
Exposed Metal Pad..................................................................... 25
Digital Inputs .............................................................................. 25
MIPI Tx Outputs (ADV7282A-M Only) ................................ 25
Typical Circuit Connections ......................................................... 26
Outline Dimensions....................................................................... 28
Ordering Guide .......................................................................... 28
Automotive Products................................................................. 28
Applications....................................................................................... 1
General Description ......................................................................... 1
Revision History ............................................................................... 2
Functional Block Diagrams............................................................. 3
Specifications..................................................................................... 4
Electrical Specifications............................................................... 4
Video Specifications..................................................................... 5
Analog Specifications................................................................... 6
Clock and I2C Timing Specifications......................................... 6
MIPI Tx Video Output and Timing Specifications
(ADV7282A-M Only).................................................................. 7
Pixel Port Timing Specifications (ADV7282A Only).............. 9
Absolute Maximum Ratings.......................................................... 10
Thermal Resistance .................................................................... 10
ESD Caution................................................................................ 10
Pin Configurations and Function Descriptions ......................... 11
Theory of Operation ...................................................................... 13
Analog Front End ....................................................................... 13
Standard Definition Processor (SDP)...................................... 13
Power Supply Sequencing.............................................................. 15
Optimal Power-Up Sequence.................................................... 15
Simplified Power-Up Sequence ................................................ 15
Power-Down Sequence.............................................................. 15
DVDDIO Supply Voltage ................................................................ 15
Crystal Oscillator Design............................................................... 16
REVISION HISTORY
5/2018—Rev. 0 to Rev. A
Changes to General Description Section ...................................... 1
9/2017—Revision 0: Initial Version
Rev. A | Page 2 of 28
Data Sheet
ADV7282A
FUNCTIONAL BLOCK DIAGRAMS
ADV7282A
CLOCK PROCESSING BLOCK
LLC
XTALP
XTALN
PLL
ADLLT PROCESSING
10-BIT ADC
DIGITAL
PROCESSING
BLOCK
AA
FILTER
A
A
1
2
IN
IN
ACE
2D COMB
DIFFERENTIAL
OR
SINGLE-ENDED
ANALOG VIDEO
INPUTS
AA
8-BIT
PIXEL DATA
P0 TO P7
+
DOWN
DITHER
FILTER
VBI SLICER
SHA
–
ADC
AA
FILTER
COLOR
DEMOD
A
A
3
4
IN
IN
AA
FILTER
2
I P
2
INTRQ
DIAGNOSTICS
REFERENCE
I C/CONTROL
DIAG1
DIAG2
SCLK SDATA ALSB RESET PWRDWN
Figure 1. ADV7282A Functional Block Diagram
CLKP
CLKN
D0P
ADV7282A-M
CLOCK PROCESSING BLOCK
MIPI
Tx
XTALP
XTALN
PLL
ADLLT PROCESSING
D0N
10-BIT ADC
DIGITAL
PROCESSING
BLOCK
AA
FILTER
A
A
1
2
IN
IN
ACE
2D COMB
DIFFERENTIAL
OR
SINGLE-ENDED
ANALOG VIDEO
INPUTS
AA
+
DOWN
DITHER
FILTER
A
A
3
4
VBI SLICER
IN
IN
SHA
–
ADC
AA
FILTER
COLOR
DEMOD
GPO0
GPO1
GPO2
A
A
5
6
IN
IN
AA
FILTER
2
I P
2
INTRQ
DIAGNOSTICS
REFERENCE
I C/CONTROL
DIAG1
DIAG2
SCLK SDATA ALSB RESET PWRDWN
Figure 2. ADV7282A-M Functional Block Diagram
Rev. A | Page 3 of 28
ADV7282A
Data Sheet
SPECIFICATIONS
ELECTRICAL SPECIFICATIONS
PVDD, AVDD, DVDD, and MVDD = 1.71 V to 1.89 V, DVDDIO = 2.97 V to 3.63 V, specified at the operating temperature range, unless otherwise
noted. MVDD only applies to the ADV7282A-M.
Table 1.
Parameter
Symbol Test Conditions/Comments
Min Typ Max Unit
STATIC PERFORMANCE
ADC Resolution
Integral Nonlinearity
Differential Nonlinearity
DIGITAL INPUTS
N
INL
DNL
10
Bits
LSB
LSB
CVBS mode
CVBS mode
2
0.6
Input High Voltage
VIH
VIL
IIN
DVDDIO = 3.3 V
DVDDIO = 1.8 V, ADV7282A only
DVDDIO = 3.3 V
DVDDIO = 1.8 V, ADV7282A only
RESET pin
2
1.2
V
V
V
V
µA
µA
µA
pF
Input Low Voltage
0.8
0.4
+10
+15
+50
10
Input Leakage Current
−10
−10
−10
SDATA, SCLK pins
PWRDWN, ALSB pins
Input Capacitance
CRYSTAL INPUT
CIN
Input High Voltage
Input Low Voltage
DIGITAL OUTPUTS
Output High Voltage
VIH
VIL
XTALN pin
XTALN pin
1.2
2.4
V
V
0.4
VOH
VOL
DVDDIO = 3.3 V, ISOURCE = 0.4 mA
DVDDIO = 1.8 V, ISOURCE = 0.4 mA, ADV7282A only 1.4
DVDDIO = 3.3 V, ISINK = 3.2 mA
V
V
V
V
µA
pF
Output Low Voltage
0.4
0.2
10
DVDDIO = 1.8 V, ISINK = 1.6 mA, ADV7282A only
High Impedance Leakage Current
Output Capacitance
ILEAK
COUT
20
POWER REQUIREMENTS1, 2, 3
Digital Input/Output (I/O) Power Supply
DVDDIO
ADV7282A-M
ADV7282A
2.97 3.3
1.62 3.3
1.71 1.8
1.71 1.8
1.71 1.8
1.71 1.8
1.5
3.63
3.63
1.89
1.89
1.89
1.89
V
V
V
V
V
V
mA
mA
mA
mA
PLL Power Supply
Analog Power Supply
Digital Power Supply
MIPI Transmitter (Tx) Power Supply
Digital I/O Supply Current
PVDD
AVDD
DVDD
MVDD
IDVDDIO
ADV7282A-M only
ADV7282A-M
ADV7282A
5
12
14
PLL Supply Current
MIPI Tx Supply Current
Analog Supply Current
Single-Ended CVBS Input
Differential CVBS Input
Y/C Input
IPVDD
IMVDD
IAVDD
ADV7282A-M only
47
69
60
75
mA
mA
mA
mA
Fully differential and pseudo differential CVBS
YPrPb Input
Digital Supply Current
Single-Ended CVBS Input
Differential CVBS Input
Y/C Input
IDVDD
70
70
70
70
mA
mA
mA
mA
Fully differential and pseudo differential CVBS
YPrPb Input
Rev. A | Page 4 of 28
Data Sheet
ADV7282A
Parameter
Symbol Test Conditions/Comments
Min Typ Max Unit
POWER-DOWN CURRENTS1
Digital I/O Supply
PLL Supply
Analog Supply
Digital Supply
IDVDDIO_PD
IPVDD_PD
IAVDD_PD
IDVDD_PD
IMVDD_PD
73
46
0.2
420
4.5
1
µA
µA
µA
µA
µA
mW
MIPI Tx Supply
Total Power Dissipation in Power-Down Mode
CRYSTAL OSCILLATOR1
Transconductance
gM
30
mA/V
1 Guaranteed by characterization.
2 Typical current consumption values are measured with nominal voltage supply levels and a Society of Motion Picture and Television Engineers (SMPTE) bar test
pattern.
3 All specifications apply when the I2P core is activated, unless otherwise stated.
VIDEO SPECIFICATIONS
PVDD, AVDD, DVDD, and MVDD = 1.71 V to 1.89 V, DVDDIO = 2.97 V to 3.63 V, specified at operating temperature range, unless otherwise noted.
Specifications guaranteed by characterization. MVDD only applies to the ADV7282A-M.
Table 2.
Parameter
Symbol
Test Conditions/Comments
Min
Typ
Max
Unit
NONLINEAR SPECIFICATIONS1
Differential Phase
Differential Gain
Luma Nonlinearity
DP
DG
LNL
CVBS input, modulated five-step
CVBS input, modulated five-step
CVBS input, five-step
0.9
0.5
2.0
Degrees
%
%
NOISE SPECIFICATIONS
Signal-to-Noise Ratio, Unweighted
SNR
Luma ramp
Luma flat field
57.1
58
60
dB
dB
dB
dB
Analog Front-End Crosstalk
Common-Mode Rejection Ratio2
LOCK TIME SPECIFICATIONS
Horizontal Lock Range
Vertical Lock Range
CMRR
73
−5
40
+5
70
%
Hz
Subcarrier Lock Range
Color Lock In Time
Synchronization Depth Range
Color Burst Range
fSC
1.3
60
kHz
Lines
%
20
5
200
200
%
Vertical Lock Time
Autodetection Switch Speed3
Fast Switch Speed4
2
100
100
Fields
Lines
ms
LUMA SPECIFICATIONS
Luma Brightness Accuracy
Luma Contrast Accuracy
CVBS, 1 V input
1
1
%
%
1 These specifications apply for all CVBS input types (NTSC, PAL, and SECAM), as well as for single-ended and differential CVBS inputs.
2 The CMRR of this circuit design is critically dependent on the external resistor matching on the circuit inputs (see the Input Networks section). The CMRR measurement
was performed with 0.1% tolerant resistors, a common-mode voltage of 1 V, and a common-mode frequency of 10 kHz.
3 Autodetection switch speed is the time required for the ADV7282A to detect which video format is present at its input, for example, PAL I or NTSC M.
4 Fast switch speed is the time required for the ADV7282A to switch from one analog input (single-ended or differential) to another, for example, switching from AIN1 to AIN2.
Rev. A | Page 5 of 28
ADV7282A
Data Sheet
ANALOG SPECIFICATIONS
PVDD, AVDD, DVDD, and MVDD = 1.71 V to 1.89 V, DVDDIO = 2.97 V to 3.63 V, specified at operating temperature range, unless otherwise noted.
Specifications guaranteed by characterization. MVDD only applies to the ADV7282A-M.
Table 3.
Parameter
Test Conditions/Comments
Min
Typ
Max
Unit
CLAMP CIRCUITRY
External Clamp Capacitor
Input Impedance
Large Clamp Source Current
Large Clamp Sink Current
Fine Clamp Source Current
Fine Clamp Sink Current
0.1
10
0.4
0.4
10
µF
Clamps switched off
MΩ
mA
mA
µA
10
µA
CLOCK AND I2C TIMING SPECIFICATIONS
AVDD, DVDD, PVDD, and MVDD = 1.71 V to 1.89 V, DVDDIO = 2.97 V to 3.63 V, specified at operating temperature range, unless otherwise noted.
Specifications guaranteed by characterization. MVDD only applies to the ADV7282A-M.
Table 4.
Parameter
Symbol
Min
Typ
Max
Unit
SYSTEM CLOCK AND CRYSTAL
Nominal Frequency
Frequency Stability
28.63636
MHz
ppm
50
I2C PORT
SCLK Frequency
400
kHz
µs
µs
µs
µs
ns
ns
ns
µs
SCLK Minimum Pulse Width High
SCLK Minimum Pulse Width Low
Hold Time (Start Condition)
Setup Time (Start Condition)
SDATA Setup Time
SCLK and SDATA Rise Times
SCLK and SDATA Fall Times
Setup Time (Stop Condition)
RESET INPUT
t1
t2
t3
t4
t5
t6
t7
t8
0.6
1.3
0.6
0.6
100
300
300
0.6
RESET Pulse Width
5
ms
t5
t3
t3
SDATA
SCLK
t1
t6
t4
t7
t8
t2
Figure 3. I2C Timing Diagram
Rev. A | Page 6 of 28
Data Sheet
ADV7282A
MIPI Tx VIDEO OUTPUT AND TIMING SPECIFICATIONS (ADV7282A-M ONLY)
PVDD, AVDD, DVDD, and MVDD = 1.71 V to 1.89 V, DVDDIO = 2.97 V to 3.63 V, specified at operating temperature range, unless otherwise noted.
The ADV7282A MIPI Tx conforms to the MIPI D-PHY Version 1.00.00 specification by characterization. The MIPI Tx clock lane of the
ADV7282A-M remains in high speed mode even when the data lane enters low power (LP) mode. For this reason, some measurements
on the clock lane that pertain to low power mode are not applicable. Unless otherwise stated, all high speed measurements were
performed with the ADV7282A-M operating in progressive mode and with a nominal 432 Mbps output data rate. Specifications
guaranteed by characterization.
Table 5.
Parameter
Symbol Test Conditions/Comments Min
Typ
Max
Unit
UNIT INTERVAL
Interlaced Output
Progressive Output
UI
4.63
2.31
ns
ns
DATA LANE LP MIPI Tx DC
SPECIFICATIONS1
Thevenin Output High Level
Thevenin Output Low Level
VOH
VOL
1.1
−50
1.2
0
1.3
+50
V
mV
DATA LANE LP MIPI Tx AC
SPECIFICATIONS1
Rise Time, 15% to 85%
Fall Time, 85% to 15%
Rise Time, 30% to 85%
25
25
35
ns
ns
ns
Data Lane LP Slew Rate vs. Load
Capacitance (CLOAD
)
Maximum Slew Rate over Entire
Vertical Edge Region
Rising edge
Falling edge
150
150
mV/ns
mV/ns
Minimum Slew Rate
400 mV ≤ VOUT ≤ 930 mV
400 mV ≤ VOUT ≤ 700 mV
700 mV ≤ VOUT ≤ 930 mV
Pulse Width of LP Exclusive OR Clock
Falling edge
Rising edge
Rising edge
First clock pulse after stop
state or last pulse before stop
state
30
30
>0
40
mV/ns
mV/ns
mV/ns
ns
All other clock pulses
20
90
ns
ns
Period of LP Exclusive OR Clock
CLOCK LANE LP MIPI Tx DC
SPECIFICATIONS1
Thevenin Output High Level
Thevenin Output Low Level
VOH
VOL
1.1
−50
1.2
0
1.3
+50
V
mV
CLOCK LANE LP MIPI Tx AC
SPECIFICATIONS1
Rise Time, 15% to 85%
Fall Time, 85% to 15%
Clock Lane LP Slew Rate
25
25
ns
ns
Maximum Slew Rate over Entire
Vertical Edge Region
Rising edge
Falling edge
150
150
mV/ns
mV/ns
Minimum Slew Rate
400 mV ≤ VOUT ≤ 930 mV
400 mV ≤ VOUT ≤ 700 mV
700 mV ≤ VOUT ≤ 930 mV
Falling edge
Rising edge
Rising edge
30
30
>0
mV/ns
mV/ns
mV/ns
Rev. A | Page 7 of 28
ADV7282A
Data Sheet
Parameter
Symbol Test Conditions/Comments Min
Typ
Max
Unit
DATA LANE HIGH SPEED MIPI Tx
SIGNALING REQUIREMENTS
See Figure 4
LP to High Speed Transition Stage
t9
Time that the D0P pin is at
OL and the D0N pin is at VOH
50
ns
V
t10
t11
|V1|
Time that the D0P and D0N
pins are at VOL
t10 plus the high speed zero
period
40 + (4 × UI)
145 + (10 × UI)
140
85 + (6 × UI)
ns
ns
High Speed Differential Voltage Swing
Differential Voltage Mismatch
Single-Ended Output High Voltages
Static Common-Mode Voltage Level
Static Common-Mode Voltage
Mismatch
200
200
270
10
360
250
5
mV p-p
mV
mV
mV
mV
150
Dynamic Common Level Variations
50 MHz to 450 MHz
Above 450 MHz
Rise Time, 20% to 80%
Fall Time, 80% to 20%
25
15
0.3 × UI
0.3 × UI
mV
mV
ns
0.15
0.15
ns
High Speed to LP Transition Stage
t12
Time that the ADV7282A-M
drives the flipped last data
bit after sending the last
payload data bit of a high
speed transmission burst
60 + (4 × UI)
ns
t13
t14
Post end of transmission rise
time (30% to 85%)
Time from start of t12 to start
of low power state following
a high speed transmission
burst
35
ns
105 + (12 × UI) ns
t15
Time that a low power state
is transmitted after a high
speed transmission burst
100
ns
CLOCK LANE HIGH SPEED MIPI Tx
SIGNALING REQUIREMENTS
LP to High Speed Transition Stage2
See Figure 4
Time that the CLKP pin is at
50
ns
ns
V
OL and the CLKN pin is at VOH
Time that the CLKP and CLKN 38
pins are at VOL
95
Clock high speed zero period 300
140
500
200
ns
mV p-p
mV
mV
mV
High Speed Differential Voltage Swing
Differential Voltage Mismatch
Single-Ended Output High Voltages
Static Common-Mode Voltage Level
Static Common-Mode Voltage Mismatch
Dynamic Common Level Variations
50 MHz to 450 MHz
Above 450 MHz
Rise Time, 20% to 80%
Fall Time, 80% to 20%
|V2|
270
10
360
250
5
150
200
mV
25
15
0.3 × UI
0.3 × UI
mV
mV
ns
0.15
0.15
ns
HIGH SPEED MIPI Tx CLOCK TO DATA
LANE TIMING REQUIREMENTS
Data to Clock Skew
0.35 × UI
0.65 × UI
ns
1 These measurements were performed with CLOAD = 50 pF.
2 The clock lane remains in high speed mode throughout normal operation. These results apply only to the ADV7282A-M during startup.
Rev. A | Page 8 of 28
Data Sheet
ADV7282A
|V |
2
CLKP/CLKN
t9
t10
t11
D0P/D0N
V
OH
|V |
1
V
OL
t13
TRANSMIT FIRST
DATA BIT
t14
t12
t15
LOW POWER
TO
HIGH SPEED
TRANSITION
HIGH SPEED
ZERO
START OF
TRANSMISSION
SEQUENCE
HIGH SPEED DATA
TRANSMISSION
HIGH SPEED
TRAIL
HIGH SPEED
TO
LOW POWER
TRANSITION
Figure 4. ADV7282A-M Output Timing Diagram (Conforms with MIPI Tx Specification)
PIXEL PORT TIMING SPECIFICATIONS (ADV7282A ONLY)
AVDD, DVDD, and PVDD = 1.71 V to 1.89 V, DVDDIO = 1.62 V to 3.63 V, specified at operating temperature range, unless otherwise noted.
Specifications guaranteed by characterization.
Table 6.
Parameter
Symbol
Test Conditions/Comments
Min
Typ
Max
Unit
CLOCK OUTPUTS
LLC Mark Space Ratio
DATA AND CONTROL OUTPUTS
t16:t17
45:55
55:45
% duty cycle
Data Output Transitional Time t18
Negative clock edge to start of valid data
(tSETUP = t17 − t18)
End of valid data to negative clock edge
(tHOLD = t16 − t19)
3.8
6.9
ns
ns
t19
t16
t17
OUTPUT LLC
t18
t19
OUTPUTS P0 TO P7
Figure 5. ADV7282A Pixel Port and Control Output Timing Diagram
Rev. A | Page 9 of 28
ADV7282A
Data Sheet
ABSOLUTE MAXIMUM RATINGS
Table 7.
THERMAL RESISTANCE
Parameter1
AVDD to GND
DVDD to GND
PVDD to GND
MVDD to GND2
DVDDIO to GND
PVDD to DVDD
MVDD to DVDD
AVDD to DVDD
Digital Inputs Voltage
Digital Outputs Voltage
Analog Inputs to Ground
Rating
Thermal performance is directly linked to printed circuit board
(PCB) design and operating environment. Careful attention to
PCB thermal design is required.
2.2 V
2.2 V
2.2 V
2.2 V
θJA is the natural convection junction to ambient thermal resistance
measured in a one cubic foot sealed enclosure as per JEDEC
JESD51. ΨJT is the junction to top thermal characterization
parameter measured on a standard test board, as per JEDEC
JESD51, allowing the heat generated in the ADV7282A die to
flow normally along preferred thermal conduction paths that more
closely represent the thermal flows in a typical application board.
4 V
−0.9 V to +0.9 V
−0.9 V to +0.9 V
−0.9 V to +0.9 V
GND − 0.3 V to DVDDIO + 0.3 V
GND − 0.3 V to DVDDIO + 0.3 V
GND − 0.3 V to AVDD + 0.3 V
2
Table 8. Thermal Resistance
Maximum Junction Temperature 125°C
(TJ MAX
Package
θJA
ΨJT
Unit
)
CP-32-121
39.6
0.86
°C/W
Storage Temperature Range
Reflow Soldering (20 sec)
−65°C to +150°C
JEDEC J-STD-020
1 JEDEC JESD51 2s2p 4-layer PCB with two signal layers and two buried solid
ground planes (GND), and with nine thermal vias connecting the exposed
pad to the ground plane (GND).
1 The absolute maximum ratings assume that the DGND pins and the exposed
pad of the ADV7282A are connected together to a common ground plane
(GND). This is part of the recommended layout scheme. See the PCB Layout
Recommendations section for more information. The absolute maximum
ratings are stated in relation to this common ground plane.
ESD CAUTION
2 MVDD only applies to the ADV7282A-M.
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
Rev. A | Page 10 of 28
Data Sheet
ADV7282A
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
DGND
1
2
3
4
5
6
7
8
24
23
A 3
IN
DIAG2
D
VDDIO
D
22 DIAG1
VDD
ADV7282A
DGND
P7
21
20
19
18
17
A
VDD
TOP VIEW
VREFN
VREFP
(Not to Scale)
P6
P5
P4
A
A
2
1
IN
IN
NOTES
1. THE EXPOSED PAD MUST BE CONNECTED,
TOGETHER WITH THE DGND PINS, TO A COMMON
GROUND PLANE (GND).
Figure 6. ADV7282A Pin Configuration
Table 9. Pin Function Descriptions, ADV7282A
Pin No.
Mnemonic
Type
Description
1, 4
2
3, 13
5 to 12
14
DGND
DVDDIO
DVDD
P7 to P0
XTALP
Ground
Power
Power
Output
Output
Ground for Digital Supply.
Digital I/O Power Supply (1.8 V or 3.3 V).
Digital Power Supply (1.8 V).
Video Pixel Output Ports.
Output Pin for the Crystal Oscillator Amplifier. Connect this pin to the external 28.63636 MHz
crystal, or leave it unconnected if an external 1.8 V, 28.63636 MHz clock oscillator source is
used to clock the ADV7282A. The crystal used with the ADV7282A must be a fundamental
mode crystal.
15
16
XTALN
PVDD
Input
Input Pin for the Crystal Oscillator Amplifier. The crystal used with the ADV7282A must be a
fundamental mode crystal. If an external 1.8 V, 28.63636 MHz clock oscillator source is used
to clock the ADV7282A, the output of the oscillator is fed into the XTALN pin.
Power
Input
Output
Output
Power
Input
PLL Power Supply (1.8 V).
17, 18, 24, 25 AIN1 to AIN4
Analog Video Input Channels.
Positive Internal Voltage Reference Output.
Negative Internal Voltage Reference Output.
Analog Power Supply (1.8 V).
Diagnostic Input 1.
19
20
21
22
23
26
VREFP
VREFN
AVDD
DIAG1
DIAG2
INTRQ
Input
Output
Diagnostic Input 2.
Interrupt Request Output. An interrupt occurs when certain signals are detected on the
input video.
27
28
RESET
ALSB
Input
Input
System Reset Input (Active Low). A minimum low reset pulse width of 5 ms is required to
reset the ADV7282A circuitry.
Address Least Significant Bit. This pin selects the I2C write address for the ADV7282A. When
ALSB is set to Logic 0, the write address is 0x40; when ALSB is set to Logic 1, the write
address is 0x42.
I2C Port Serial Data Input/Output.
I2C Port Serial Clock Input. The maximum clock rate is 400 kHz.
Power-Down. A logic low on this pin places the ADV7282A in power-down mode.
29
30
31
32
SDATA
SCLK
PWRDWN
LLC
Input/output
Input
Input
Output
Line Locked Clock for Output Pixel Data. The clock output is nominally 27 MHz, but it
increases or decreases according to the video line length.
EPAD (EP)
Exposed Ground Pad. The exposed pad must be connected, together with the DGND pins,
to a common ground plane (GND).
Rev. A | Page 11 of 28
ADV7282A
Data Sheet
DGND
1
2
3
4
5
6
7
8
24
23
A
A
4
3
IN
D
VDDIO
IN
D
22 DIAG1
VDD
ADV7282A-M
DGND
INTRQ
GPO2
GPO1
GPO0
21
20
19
18
17
A
VDD
TOP VIEW
VREFN
VREFP
A
A
(Not to Scale)
2
1
IN
IN
NOTES
1. THE EXPOSED PAD MUST BE CONNECTED,
TOGETHER WITH THE DGND PINS, TO A COMMON
GROUND PLANE (GND).
Figure 7. Pin Configuration, ADV7282A-M
Table 10. Pin Function Descriptions, ADV7282A-M
Pin No.
Mnemonic Type
Description
1, 4
2
3
DGND
DVDDIO
DVDD
Ground
Ground for Digital Supply.
Digital I/O Power Supply (3.3 V).
Digital Power Supply (1.8 V).
Interrupt Request Output. An interrupt occurs when certain signals are detected on the
input video.
Power
Power
Output
5
INTRQ
6 to 8
GPO2 to
GPO0
Output
General-Purpose Outputs. These pins can be configured via I2C to allow control of external
devices.
9
D0P
D0N
CLKP
CLKN
MVDD
XTALP
Output
Output
Output
Output
Power
Positive MIPI Differential Data Output.
Negative MIPI Differential Data Output.
Positive MIPI Differential Clock Output.
Negative MIPI Differential Clock Output.
MIPI Digital Power Supply (1.8 V).
Output Pin for the Crystal Oscillator Amplifier. Connect this pin to the external 28.63636 MHz
crystal, or leave it unconnected if an external 1.8 V, 28.63636 MHz clock oscillator source is
used to clock the ADV7282A-M. The crystal used with the ADV7282A-M must be a
fundamental mode crystal.
10
11
12
13
14
Output
15
16
XTALN
PVDD
Input
Input Pin for the Crystal Oscillator Amplifier. The crystal used with the ADV7282A-M must
be a fundamental mode crystal. If an external 1.8 V, 28.63636 MHz clock oscillator source is
used to clock the ADV7282A-M, the output of the oscillator is fed into the XTALN pin.
Power
PLL Power Supply (1.8 V).
17, 18, 23, 24,
26, 27
AIN1 to AIN6 Input
Analog Video Input Channels.
19
20
21
22
25
28
VREFP
VREFN
AVDD
DIAG1
DIAG2
RESET
Output
Output
Power
Input
Input
Input
Positive Internal Voltage Reference Output.
Negative Internal Voltage Reference Output.
Analog Power Supply (1.8 V).
Diagnostic Input 1.
Diagnostic Input 2.
System Reset Input (Active Low). A minimum low reset pulse width of 5 ms is required to
reset the ADV7282A-M circuitry.
29
ALSB
Input
Address Least Significant Bit. This pin selects the I2C write address for the ADV7282A-M.
When ALSB is set to Logic 0, the write address is 0x40; when ALSB is set to Logic 1, the write
address is 0x42.
30
31
32
SDATA
SCLK
PWRDWN
EPAD (EP)
Input/output
Input
Input
I2C Port Serial Data Input/Output.
I2C Port Serial Clock Input. The maximum clock rate is 400 kHz.
Power-Down. A logic low on this pin places the ADV7282A-M in power-down mode.
Exposed Ground Pad. The exposed pad must be connected, together with the DGND pins,
to a common ground plane (GND).
Rev. A | Page 12 of 28
Data Sheet
ADV7282A
THEORY OF OPERATION
The ADV7282A is a versatile one-chip, multiformat video decoder
that automatically detects standard analog baseband video signals
and converts them into a YCbCr 4:2:2 component video data
stream. The ADV7282A supports video signals compatible with
worldwide NTSC, PAL, and SECAM standards.
small and large signal noise rejection, improved electromagnetic
interference (EMI), and the ability to absorb ground bounce.
The architecture can support true differential, pseudo differential,
and single-ended signals.
In conjunction with an external resistor divider, the ADV7282A
can provide a common-mode input range of 4 V, facilitating the
removal of large signal, common-mode transients present on
both video inputs.
The analog front ends of the ADV7282A feature an input mux
(4-channel for ADV7282A, 6-channel for ADV7282A-M), a
differential to single-ended converter and a single 10-bit ADC.
The analog video inputs accept single-ended, pseudo differential,
and fully differential composite video signals as well as S-Video
(Y/C) and YPbPr video signals, supporting a wide range of
automotive and consumer video sources.
The external resistor divider is required before each analog
input channel to ensure that the input signal is kept within the
range of the ADC. Current and voltage clamps in the circuit
ensure that the video signal remains within the range on the ADC.
The incoming analog video is converted into a digital 8-bit
YCrCb 4:2:2 video stream that is output either via a digital 8-bit
ITU-R BT.656 video stream (ADV7282A) or via a MIPI Tx
interface (ADV7282A-M). External horizontal sync (HS), vertical
sync (VS), and field sync signals are available for the ITU-R BT.656
interface to provide timing references for LCD controllers and
other video ASICs.
The single 10-bit ADC digitizes the analog video before it is
applied to the SDP. Table 11 shows the three ADC clocking rates
that are determined by the video input format to be processed.
These clock rates ensure 4× oversampling per channel for CVBS,
Y/C, and YPrPb modes.
Table 11. ADC Clock Rates
Oversampling
Rate per Channel
The ADV7282A features an advanced I2P function to convert
interlaced input video to a progressive video output with no
requirement for external memory. The I2P conversion uses edge
adaptive technology to minimize video defects on low angle lines.
Input Format
CVBS
S-Video (Y/C)2
YPrPb2
ADC Clock Rate (MHz)1
57.27
114
172
4×
4×
4×
The ac-coupled connection of input video signals to the
ADV7282A provides STB protection; two diagnostic sense
inputs are available. The ADV7282A also offers a downdither
mode, adaptive contrast enhancement (ACE) and general-
purpose outputs (ADV7282A-M only).
1 Based on a 28.63636 MHz clock input to the ADV7282A.
2 Configuration writes are required for the different S-Video (Y/C) and YPrPb
modes.
STANDARD DEFINITION PROCESSOR (SDP)
The SDP in the ADV7282A is capable of decoding a large
selection of baseband video signals in composite (both single-
ended and differential), S-Video (Y/C), and component formats.
The video standards supported by the video processor include
The ADV7282A is programmed via a 2-wire, serial bidirectional
port (I2C compatible) and can communicate with other devices
INTRQ
via a hardware interrupt pin,
.
The ADV7282A is fabricated in a low power 1.8 V CMOS process
and are provided in a space-saving LFCSP surface-mount, RoHS
compliant package.
•
PAL B, PAL D, PAL G, PAL H, PAL I, PAL M, PAL N,
PAL Nc, PAL 60
NTSC J, NTSC M, NTSC 4.43
•
•
The ADV7282A is available in an automotive grade rated over
the −40°C to +105°C temperature range, making them ideal for
automotive applications.
SECAM B, SECAM D, SECAM G, SECAM K, SECAM L
The SDP in the ADV7282A can automatically detect the video
standard and process it accordingly.
ANALOG FRONT END
The ADV7282A has a five-line, superadaptive, 2D comb filter that
provides superior chrominance and luminance separation when
decoding a composite video signal. This highly adaptive filter
automatically adjusts its processing mode according to the video
standard and signal quality without requiring user intervention.
Video user controls such as brightness, contrast, saturation, and
hue are also available in the ADV7282A.
The analog front end (AFE) of the ADV7282A is composed of
an input mux, a differential to single-ended converter with
clamp circuitry, a set of four antialiasing filters, and a single
10-bit ADC.
The input mux (4-channel for ADV7282A, 6-channel for
ADV7282A-M) enables multiple composite video signals to be
applied to the SDP and is software controlled.
The ADV7282A implements a patented Adaptive Digital Line
Length Tracking (ADLLT™) algorithm to track varying video
line lengths from sources such as a VCR. ADLLT enables the
ADV7282A to track and decode poor quality video sources such
as VCRs and noisy sources from tuner outputs, VCD players, and
The next stage in the AFE features the differential to single-
ended converter and the clamp circuitry. The incorporation of a
differential front end allows differential video to connect
directly to the ADV7282A. The differential front end enables
Rev. A | Page 13 of 28
ADV7282A
Data Sheet
camcorders. The ADV7282A contains a chroma transient
improvement (CTI) processor that sharpens the edge rate of
chroma transitions, resulting in sharper vertical transitions.
The SDP can handle a variety of vertical blanking interval (VBI)
data services, such as closed captioning (CCAP), wide screen
signaling (WSS), copy generation management system (CGMS),
and teletext data slicing for world standard teletext (WST). Data
is transmitted via the 8-bit video output port as ancillary data
packets (ANC).
The ADV7282A features an automatic gain control (AGC)
algorithm to ensure that the optimum luma gain is selected as
the input video varies in brightness.
The ADV7282A is fully Rovi™ (formerly Macrovision® and now
rebranded as TiVo upon acquisition of the same) compliant;
detection circuitry enables Type I, Type II, and Type III protection
levels to be identified and reported to the user. The SDP is fully
robust to all Rovi signal inputs.
ACE is an algorithm that automatically varies the contrast level
applied across an image to enhance the picture detail visible. This
automatic variation enables the contrast in the dark areas of an
image to be increased without saturating the bright areas, which
is particularly useful in automotive applications where it can be
important to be able to clearly discern objects in shaded areas.
Downdithering from eight bits to six bits enables ease of design
for standard LCD panels.
Rev. A | Page 14 of 28
Data Sheet
ADV7282A
POWER SUPPLY SEQUENCING
While the supplies are established, ensure that a lower rated
OPTIMAL POWER-UP SEQUENCE
supply does not go above a higher rated supply level. During
power-up, all supplies must adhere to the specifications listed in
the Absolute Maximum Ratings section.
The optimal power-up sequence for the ADV7282A is
guaranteed by production testing.
The optimal power-up sequence for the ADV7282A is to first
power up the 3.3 V DVDDIO supply, followed by the 1.8 V supplies:
POWER-DOWN SEQUENCE
DVDD, PVDD, AVDD, and MVDD (for the ADV7282A-M).
The ADV7282A supplies can be deasserted simultaneously if
D
VDDIO does not go below a lower rated supply.
When powering up the ADV7282A, follow these steps. During
power-up, all supplies must adhere to the specifications listed in
the Absolute Maximum Ratings section.
DVDDIO SUPPLY VOLTAGE
For correct operation of the ADV7282A-M, the DVDDIO supply
must be from 2.97 V to 3.63 V.
PWRDWN
RESET
pins (pull the pins low).
1. Assert the
and
2. Power up the DVDDIO supply.
3. After DVDDIO is fully asserted, power up the 1.8 V supplies.
4. After the 1.8 V supplies are fully asserted, pull
The ADV7282A, however, can operate with a nominal DVDDIO
voltage of 1.8 V. In this case, apply the power-up sequences
described in the Optimal Power-Up Sequence section. The only
change is that DVDDIO is powered up to 1.8 V instead of 3.3 V,
PWRDWN
the
pin high.
RESET
5. Wait 5 ms and then pull the
6. After all power supplies and the
pin high.
PWRDWN
PWRDWN
RESET
and the
and
pins of the ADV7282A are
RESET
pins
and
powered up to 1.8 V instead of 3.3 V.
are powered up and stable, wait an additional 5 ms before
When the ADV7282A operates with a nominal DVDDIO voltage
of 1.8 V, set the drive strength of all digital outputs to the
maximum values.
initiating I2C communication with the ADV7282A-M.
SIMPLIFIED POWER-UP SEQUENCE
When DVDDIO is 1.8 V, do not pull any pin of the ADV7282A up
to 3.3 V. For example, the I2C pins of the ADV7282A (SCLK
and SDATA) must also be pulled up to 1.8 V instead of 3.3 V.
The simplified power-up sequence is guaranteed by
characterization.
Alternatively, the ADV7282A can be powered up by asserting all
PWRDWN
pin must remain low. After the supplies
are fully asserted, wait for at least 5 ms before
supplies and the
RESET
and
bringing the
pin simultaneously. During this
operation, the
PWRDWN
RESET
RESET
pin is fully
pin high. After the
asserted wait a further 5 ms before initiating I2C communication
with the ADV7282A.
3.3V
1.8V
3.3V SUPPLY
PWRDWN PIN
RESET PIN
1.8V SUPPLIES
PWRDWN PIN
POWER-UP
RESET PIN
POWER-UP
3.3V SUPPLY
POWER-UP
1.8V SUPPLIES
POWER-UP
TIME
5ms
5ms
WAIT
RESET
OPERATION
Figure 8. Optimal Power-Up Sequence
Rev. A | Page 15 of 28
ADV7282A
Data Sheet
CRYSTAL OSCILLATOR DESIGN
The ADV7282A needs a stable and accurate clock source to
guarantee their operation. This clock is typically provided by a
crystal resonator (XTAL) but can also be provided by a clock
oscillator.
The evaluation of the ADV7282A was completed using an
XTAL with typical characteristics (see Table 12).
Table 12. Reference XTAL Characteristics
Characteristic
Value
Unit
The required circuitry for an XTAL is illustrated in Figure 18
and Figure 19. A damping resistor (RDAMP) is required on the
output of the ADV7282A XTAL amplifier (XTALP). The
purpose of this damping resistor is to limit the current flowing
through the XTAL and to limit the voltage across the XTAL
amplifier. To define the appropriate value of the damping
resistor RDAMP (see the Typical Circuit Connections section),
consult the accompanying calculator tool (visit the design
resources section at www.analog.com/ADV7282A to
download).
Package
3.2 × 2.5 × 0.8 mm
Nominal Frequency
Mode of Oscillation
Frequency Calibration (at 25°C)
Frequency Temperature Stability
Tolerance
Operating Temperature Range
Maximum Equivalent Series
Resistance
Load Capacitance
Drive Level
Shunt Capacitance (Maximum)
Aging per Year
28.63636
MHz
Fundamental
20
50
ppm
ppm
−40 to +125
25
°C
Ω
12
200
5
pF
µW
pF
The other components in the XTAL circuit must be chosen
carefully, for example, incorrectly selected load capacitors may
result in an offset to the crystal oscillation frequency. For more
information on such considerations, see the AN-1260 Application
Note, Crystal Design Considerations for Video Decoders, HDMI
Receivers, and Transceivers. After the XTAL circuit is defined, it
is recommended to consult with the XTAL vendor to ensure
that the design operates with sufficient margin across all
conditions.
3
ppm
The values in Table 12 are provided for reference only. It is
recommended to characterize the operation of the XTAL circuit
thoroughly across the operating temperature range of the
application, in conjunction with the XTAL vendor, prior to
releasing any new design.
Rev. A | Page 16 of 28
Data Sheet
ADV7282A
INPUT NETWORKS
An input network (external resistor and capacitor circuit) is
required on the AINx input pins of the ADV7282A. The
components of the input network depend on the video format
selected for the analog input.
Fully differential video transmission involves transmitting
two complementary CVBS signals. Pseudo differential video
transmission involves transmitting a CVBS signal and a source
ground signal.
Differential video transmission has several key advantages over
single-ended transmission, including the following:
SINGLE-ENDED INPUT NETWORK
Figure 9 shows the input network to use on each AINx input
pin of the ADV7282A when using any of the following video
input formats:
•
•
•
Inherent small signal and large signal noise rejection
Improved EMI performance
Ability to absorb ground bounce
•
•
•
Single-ended CVBS
YC (S-Video)
YPrPb
Resistor R1 provides the radio frequency (RF) end termination
for the differential CVBS input lines. For a pseudo differential
CVBS input, a value of 75 Ω is recommended for R1. For a fully
differential CVBS input, a value of 150 Ω is recommended for R1.
INPUT
CONNECTOR
100nF
24Ω
EXT
ESD
VIDEO INPUT
FROM SOURCE
A
x
IN
The 1.3 kΩ and 430 Ω resistors create a resistor divider with a
gain of 0.25. The resistor divider attenuates the amplitude of the
input analog video, but increases the input common-mode range
of the ADV7282A to 4 V p-p. Amplifiers within the ADC restore
the amplitude of the input signal to maintain SNR performance.
51Ω
Figure 9. Single-Ended Input Network
The 24 Ω and 51 Ω resistors supply the 75 Ω end termination
required for the analog video input. These resistors also create a
resistor divider with a gain of 0.68. The resistor divider attenuates
the amplitude of the input analog video and scales the input to the
ADC range of the ADV7282A. This resistor divider allows an
input range to the ADV7282A of up to 1.47 V p-p. Amplifiers
within the ADC restore the amplitude of the input signal so that
SNR performance is maintained.
The 100 nF ac coupling capacitor removes the dc bias of the analog
input video before it is fed into an AINx pin of the ADV7282A.
The clamping circuitry within the ADV7282A restores the dc
bias of the input signal to the optimal level before it is fed into
the ADC of the ADV7282A.
The combination of the 1.3 kΩ and 430 Ω resistors and the
100 nF ac coupling capacitors limits the current flow into the
ADV7282A during STB events (see the STB Protection section).
The 100 nF ac coupling capacitor removes the dc bias of the analog
input video before it is fed into an AINx pin. The clamping
circuitry within the ADV7282A restores the dc bias of the input
signal to the optimal level before it is fed into the ADC of the
ADV7282A.
To achieve optimal performance, the 1.3 kΩ and 430 Ω resistors
must be closely matched; that is, all 1.3 kΩ and 430 Ω resistors
must have the same resistance tolerance, and this tolerance must
be as low as possible.
DIFFERENTIAL INPUT NETWORK
STB PROTECTION
Figure 10 shows the input network to use when differential CVBS
video is input on the AINx input pins of the ADV7282A.
In differential mode, the ADV7282A is protected against STB
events by the external 100 nF ac coupling capacitors (see
Figure 10). The external input network resistors are sized to be
large enough to reduce the current flow during an STB event
but small enough not to affect the operation of the ADV7282A.
INPUT
CONNECTOR
100nF
1.3kΩ
A
1
IN
430Ω
EXT
ESD
VIDEO INPUT
FROM SOURCE
R1
The power rating of the input network resistors must be chosen to
withstand the high voltages of STB events. Similarly, the breakdown
voltage of the ac coupling capacitors must be chosen to be robust
to STB events. The R1 resistor is protected because no current
or limited current flows through it during an STB event.
430Ω
100nF
1.3kΩ
A
2
IN
INPUT
CONNECTOR
Figure 10. Differential Input Network
The ADV7282A provides two STB diagnostic pins that generate
an interrupt when an STB event occurs. For more information,
see the STB Diagnostics section.
Rev. A | Page 17 of 28
ADV7282A
Data Sheet
APPLICATIONS INFORMATION
INPUT CONFIGURATION
STB DIAGNOSTICS
The input format of the ADV7282A is specified using the
INSEL[4:0] bits (see Table 13). These bits also configure the SDP
core to process CVBS, differential CVBS, S-Video (Y/C), or
component (YPrPb) format. The INSEL[4:0] bits are located in
the user sub map at Address 0x00, Bits[4:0]. For more information
about the registers, see the Register Maps section.
The ADV7282A senses an STB event via the DIAG1 and DIAG2
pins. The DIAG1 and DIAG2 pins can sense an STB event on
either the positive or the negative differential input because of
the negligible voltage drop across Resistor R1.
R5
DIAG1
The INSEL[4:0] bits specify predefined analog input routing
schemes, eliminating the need for manual mux programming
and allowing the user to route the various video signal types to
the decoder. For example, if the CVBS input is selected, the
remaining channels are powered down.
INPUT
R4
CONNECTOR
100nF
1.3kΩ
A
1
IN
430Ω
EXT
ESD
VIDEO INPUT
FROM SOURCE
R1
430Ω
100nF
1.3kΩ
A
2
IN
INPUT
CONNECTOR
Figure 11. Diagnostic Connections
Resistors R4 and R5 divide down the voltage at the input connector
to protect a DIAGx pin from an STB event. The DIAGx pin
circuitry compares this voltage to a programmable reference
voltage, known as the diagnostic slice level. When the diagnostic
slice level is exceeded, an STB event occurs.
Table 13. Input Format Specified by the INSEL[4:0] Bits
Analog Inputs
INSEL[4:0]
Bit Value
00000
00001
00010
00011
00100
00101
00110
00111
01000
01001
01010
01011
01100
01101
01110
01111
10000
10001
Video Format
CVBS
CVBS
CVBS
CVBS
Reserved
Reserved
CVBS
ADV7282A
ADV7282A-M
CVBS input on AIN1
CVBS input on AIN2
Reserved
Reserved
Reserved
CVBS input on AIN1
CVBS input on AIN2
CVBS input on AIN3
CVBS input on AIN4
Reserved
Reserved
Reserved
CVBS input on AIN3
CVBS input on AIN4
Y input on AIN1; C input on AIN2
Reserved
Reserved
Y input on AIN3; C input on AIN4
Reserved1
CVBS input on AIN5
CVBS input on AIN6
Y input on AIN1; C input on AIN2
Y input on AIN3; C input on AIN4
Reserved
Y input on AIN5; C input on AIN6
Y input on AIN1; Pb input on AIN2; Pr input on AIN3
Reserved
CVBS
S-Video (Y/C)
S-Video (Y/C)
Reserved
S-Video (Y/C)
YPrPb
Reserved
Reserved
Differential CVBS Positive input on AIN1; negative input on AIN2
Differential CVBS Reserved
Reserved
Differential CVBS Positive input on AIN3; negative input on AIN4
10010 to 11111 Reserved Reserved
Positive input on AIN1; negative input on AIN2
Positive input on AIN3; negative input on AIN4
Reserved
Positive input on AIN5; negative input on AIN6
Reserved
Reserved
1 Note that it is possible for the ADV7282A to receive YPbPr formats; however, a manual muxing scheme is required. In this case luma (Y) is fed in on AIN1 or AIN3, blue
chroma (Pb) is fed in on AIN4, and red chroma (Pr) is fed in on AIN2.
Rev. A | Page 18 of 28
Data Sheet
ADV7282A
When a DIAGx pin voltage exceeds the diagnostic slice level
voltage, a hardware interrupt is triggered and indicated by
Table 15. DIAG1_SLICE_LEVEL[2:0] Settings
DIAG1_SLICE_LEVEL[2:0]
Setting
Diagnostic Slice Level
INTRQ
the
pin. A readback register is also provided, allowing
000
75 mV
the user to determine the DIAGx pin on which the STB event
occurred.
001
010
011 (Default)
100
101
225 mV
375 mV
525 mV
675 mV
825 mV
975 mV
1.125 V
Use Equation 1 to find the trigger voltage for a selected
diagnostic slice level.
R5 +R4
(1)
VSTB _TRIGGER
=
× DIAGNOSTIC_SLICE_LEVEL
110
111
R5
where:
DIAG2 Pin
VSTB_TRIGGER is the minimum voltage required at the input
connector to trigger the STB interrupt on the ADV7282A.
DIAGNOSTIC_SLICE_LEVEL is the programmable reference
voltage.
DIAG2_SLICER_PWRDN, Address 0x5E, Bit 6,
User Sub Map
This bit powers up or powers down the diagnostic circuitry for
the DIAG2 pin.
PROGRAMMING THE STB DIAGNOSTIC FUNCTION
By default, the STB diagnostic function is disabled on the
ADV7282A. To enable the diagnostic function, follow the
instructions in this section.
Table 16. DIAG2_SLICER_PWRDN Function
DIAG2_SLICER_PWRDN
Setting
Diagnostic Slice Level
DIAG1 Pin
0
Power up the diagnostic circuitry
for the DIAG2 pin.
Power down the diagnostic
circuitry for the DIAG2 pin.
DIAG1_SLICER_PWRDN, Address 0x5D, Bit 6,
User Sub Map
1 (Default)
This bit powers up or powers down the diagnostic circuitry for
the DIAG1 pin.
DIAG2_SLICE_LEVEL[2:0], Address 0x5E, Bits[4:2],
User Sub Map
Table 14. DIAG1_SLICER_PWRDN Function
The DIAG2_SLICE_LEVEL[2:0] bits allow the user to set the
diagnostic slice level for the DIAG2 pin. When a voltage greater
than the diagnostic slice level is seen on the DIAG2 pin, an STB
interrupt is triggered.
DIAG1_SLICER_PWRDN
Setting
Diagnostic Slice Level
0
Power up the diagnostic circuitry
for the DIAG1 pin.
1 (Default)
Power down the diagnostic
circuitry for the DIAG1 pin.
For the diagnostic slice level to be set correctly, the diagnostic
circuitry for the DIAG2 pin must be powered up (see Table 16).
DIAG1_SLICE_LEVEL[2:0], Address 0x5D, Bits[4:2],
User Sub Map
Table 17. DIAG2_SLICE_LEVEL[2:0] Settings
DIAG2_SLICE_LEVEL[2:0]
Setting
Diagnostic Slice Level
75 mV
225 mV
375 mV
525 mV
The DIAG1_SLICE_LEVEL[2:0] bits allow the user to set the
diagnostic slice level for the DIAG1 pin. When a voltage greater
than the diagnostic slice level is seen on the DIAG1 pin, an STB
interrupt is triggered.
000
001
010
011 (Default)
100
For the diagnostic slice level to be set correctly, the diagnostic
circuitry for the DIAG1 pin must be powered up (see Table 14).
675 mV
825 mV
101
110
975 mV
111
1.125 V
Rev. A | Page 19 of 28
ADV7282A
Data Sheet
ADAPTIVE CONTRAST ENHANCEMENT (ACE)
ITU-R BT.656 Tx CONFIGURATION (ADV7282A
ONLY)
The ADV7282A can increase the contrast of an image depending
on the content of the picture, brightening and darkening areas.
The optional ACE feature enables the contrast within dark areas
to increase without significantly affecting the bright areas. The
ACE feature is particularly useful in automotive applications,
where it can be important to discern objects in shaded areas.
The ADV7282A receives analog video and outputs digital video
according to the ITU-R BT.656 specification. The ADV7282A
outputs the ITU-R BT.656 video data stream over the P0 to P7
data pins and has an LLC pin.
Video data is output over the P0 to P7 pins in YCrCb 4:2:2 format.
Synchronization signals are automatically embedded in the video
data signal in accordance with the ITU-R BT.656 specification.
The ACE function is disabled by default. To enable the ACE
function, execute the register writes shown in Table 18. To
disable the ACE function, execute the register writes shown in
Table 19.
The LLC output clocks the output data on the P0 to P7 pins at a
nominal frequency of 27 MHz.
I2P FUNCTION
P0
VIDEO
DECODER
ADV7282A
P1
P2
The advanced I2P function allows the ADV7282A to convert an
interlaced video input into a progressive video output. This
function is performed without the need for external memory.
The ADV7282A uses edge adaptive technology to minimize
video defects on low angle lines.
The I2P function is disabled by default. To enable the I2P func-
tion, use the recommended scripts from Analog Devices, Inc.,
available at www.analog.com/ADV7282A.
P3
P4
P5
P6
P7
ITU-R BT.656
DATA
STREAM
ANALOG
VIDEO
INPUT
ANALOG
FRONT
END
STANDARD
DEFINITION
PROCESSOR
LLC
Figure 12. ITU-R BT.656 Output Stage of the ADV7282A
Table 18. Register Writes to Enable the ACE Function
Register Map
Register Address
Register Write
0x40
0x80
Description
User Sub Map (0x40 or 0x42)
User Sub Map 2 (0x40 or 0x42)
User Sub Map 2 (0x40 or 0x42)
0x0E
0x80
0x0E
Enter User Sub Map 2
Enable ACE
Reenter user sub map
0x00
Table 19. Register Writes to Disable the ACE Function
Register Map
Register Address
Register Write
0x40
0x00
Description
User Sub Map (0x40 or 0x42)
User Sub Map 2 (0x40 or 0x42)
User Sub Map 2 (0x40 or 0x42)
0x0E
0x80
0x0E
Enter User Sub Map 2
Disable ACE
Reenter user sub map
0x00
Rev. A | Page 20 of 28
Data Sheet
ADV7282A
Table 20. Main Map I2C Addresses
MIPI Tx OUTPUT (ADV7282A-M ONLY)
R/ Bit
W
ALSB Pin
Slave Address
0x40 (write)
0x41 (read)
0x42 (write)
0x43 (read)
The decoder in the ADV7282A-M outputs an ITU-R BT.656
data stream. The ITU-R BT.656 data stream is connected into a
CSI-2 Tx module. Data from the CSI-2 Tx module is fed into a
D-PHY physical layer and output serially from the device.
0
0
1
1
0
1
0
1
The output of the ADV7282A-M consists of a single data
channel on the D0P and D0N lanes and a clock channel on the
CLKP and CLKN lanes.
The ALSB pin controls Bit 1 of the slave address. By changing
the logic level of the ALSB pin, it is possible to control two
ADV7282A devices in an application without using the same
I2C slave address. The LSB (Bit 0) specifies either a read or write
operation: Logic 1 corresponds to a read operation, and Logic 0
corresponds to a write operation.
Video data is output over the data lanes in high speed mode.
The data lanes enter low power mode during the horizontal
and vertical blanking periods.
The clock lanes clock the output video. After the ADV7282A-M
is programmed, the clock lanes exit low power mode and remain
in high speed mode until the device is reset or powered down.
To control the device on the bus, use the following protocol:
1. The master initiates a data transfer by establishing a start
condition, defined as a high to low transition on SDATA
while SCLK remains high, and indicates that an
address/data stream follows.
The ADV7282A-M outputs video data in an 8-bit, YCrCb, 4:2:2
format. When the I2P core is disabled, the video data is output
in an interlaced format at a nominal data rate of 216 Mbps. When
the I2P core is enabled, the video data is output in a progressive
format at a nominal data rate of 432 Mbps (see the I2P Function
section for more information).
2. All peripherals respond to the start condition and shift
W
the next eight bits (the 7-bit address plus the R/ bit).
The bits are transferred from MSB to LSB.
3. The peripheral that recognizes the transmitted address
responds by pulling the data line low during the ninth
clock pulse; this is known as an acknowledge (ACK) bit.
4. All other devices withdraw from the bus and maintain an
idle condition. In the idle condition, the device monitors
the SDATA and SCLK lines for the start condition and the
correct transmitted address.
I2C PORT DESCRIPTION
The ADV7282A supports a 2-wire, I2C-compatible serial interface.
Two inputs, serial data (SDATA) and serial clock (SCLK), carry
information between the ADV7282A and the system I2C master
controller. The I2C port of the ADV7282A allows the user to set
up and configure the decoder and to read back captured VBI data.
The ADV7282A has a variety of possible I2C slave addresses and
subaddresses (see the Register Maps section). The main map of
the ADV7282A has four possible slave addresses for read and
write operations, depending on the logic level of the ALSB pin
(see Table 20).
W
The R/ bit determines the direction of the data. Logic 0 on the
LSB of the first byte means that the master writes information
to the peripheral. Logic 1 on the LSB of the first byte means that
the master reads information from the peripheral.
D0P
(1 BIT)
CSI Tx DATA
OUTPUT (8 BITS)
D0N
ITU-R BT.656
DATA
STREAM
ANALOG
VIDEO
INPUT
(1 BIT)
DATA LANE LP
SIGNALS (2 BITS)
VIDEO
DECODER
CSI-2
Tx
D-PHY
Tx
CLKP
(1 BIT)
CLOCK LANE LP
SIGNALS (2 BITS)
CLKN
(1 BIT)
Figure 13. MIPI Tx Output Stage of the ADV7282A-M
Rev. A | Page 21 of 28
ADV7282A
Data Sheet
The ADV7282A acts as standard I2C slave devices on the bus.
The data on the SDATA pin is eight bits long, supporting the 7-bit
only one start condition, one stop condition, or a single stop
condition followed by a single start condition. If an invalid
subaddress is issued by the user, the ADV7282A does not issue
an acknowledge, and returns to the idle condition.
W
address plus the R/ bit. The device has subaddresses to enable
access to the internal registers; therefore, it interprets the first
byte as the device address and the second byte as the starting
subaddress. The subaddresses auto-increment, allowing data to be
written to or read from the starting subaddress. A data transfer is
always terminated by a stop condition. The user can also access
any unique subaddress register individually without updating
all the registers.
If the highest subaddress is exceeded in auto-increment mode,
take one of the following actions:
•
In read mode, the register contents of the highest subaddress
continue to output until the master device issues a no
acknowledge, indicating the end of a read. A no acknowledge
condition occurs when the SDATA line is not pulled low
on the ninth pulse.
Stop and start conditions can be detected at any stage during the
data transfer. If these conditions are asserted out of sequence with
normal read and write operations, they cause an immediate jump
to the idle condition. During a given SCLK high period, issue
•
In write mode, the data for the invalid byte is not loaded into
a subaddress register. A no acknowledge is issued by the
ADV7282A, and the device returns to the idle condition.
SDATA
SCLK
S
P
1–7
8
9
1–7
8
9
1–7
DATA
8
9
START ADDR R/W ACK SUBADDRESS ACK
ACK
STOP
Figure 14. Bus Data Transfer
WRITE
S
S
SLAVE ADDR A(S) SUBADDRESS A(S)
LSB = 0
DATA
A(S)
DATA
A(M)
A(S) P
SEQUENCE
LSB = 1
READ
SEQUENCE
SLAVE ADDR A(S) SUBADDRESS A(S)
S
SLAVE ADDR A(S)
DATA
DATA
A(M) P
S = START BIT
P = STOP BIT
A(S) = ACKNOWLEDGE BY SLAVE
A(M) = ACKNOWLEDGE BY MASTER
A(S) = NO ACKNOWLEDGE BY SLAVE
A(M) = NO ACKNOWLEDGE BY MASTER
Figure 15. Read and Write Sequence
Rev. A | Page 22 of 28
Data Sheet
ADV7282A
REGISTER MAPS
The ADV7282A contains three register maps: the main register
map, the video postprocessor (VPP) map, and the CSI map.
Interrupt/VDP Sub Map
The interrupt/VDP sub map contains registers that program
INTRQ
The interrupt/VDP sub map has the same I2C slave address as
the main map. To access the interrupt/VDP sub map, set the
SUB_USR_EN[1:0] bits in the main map (Address 0x0E,
Bits[6:5]) to 01.
The main register map contains three sub maps: the user sub
map, the interrupt/VDP sub map, and User Sub Map 2 (see
Figure 16).
internal interrupts, control the
pin, and decode VBI data.
For more information about the ADV7282A registers, see the
ADV7280A/ADV7281A/ADV7282A Device Manual.
Main Map
User Sub Map 2
The I2C slave address of the main map of the ADV7282A is set
by the ALSB pin (see Table 20). The main map allows the user to
program the I2C slave addresses of the VPP and CSI maps. The
three sub maps are accessed by writing to the SUB_USR_EN[1:0]
bits (Address 0x0E, Bits[6:5]) within the user sub map (see
Figure 16 and Table 21).
User Sub Map 2 contains registers that control the ACE, down-
dither, and fast lock functions. It also contains controls that set the
acceptable input luma and chroma limits before the ADV7282A
enters free run and color kill modes.
User Sub Map 2 has the same I2C slave address as the main map.
To access User Sub Map 2, set the SUB_USR_EN[1:0] bits in the
user sub map (Address 0x0E, Bits[6:5]) to 10.
User Sub Map
The user sub map contains registers that program the AFE and
digital core of the ADV7282A. The user sub map has the same
I2C slave address as the main map. To access the user sub map,
set the SUB_USR_EN[1:0] bits in the user sub map (Address 0x0E,
Bits[6:5]) to 00.
MAIN MAP
VPP MAP
CSI MAP
DEVICE ADDRESS
DEVICE ADDRESS
DEVICE ADDRESS
ALSB PIN LOW
WRITE: 0x40
READ: 0x41
ALSB PIN HIGH
WRITE: 0x42
READ: 0x43
WRITE: 0x84 (RECOMMENDED
READ: 0x85 SETTINGS)
WRITE: 0x88 (RECOMMENDED
READ: 0x89 SETTINGS)
VPP MAP DEVICE ADDRESS IS
PROGRAMMABLE AND SET BY
REGISTER 0xFD IN THE USER
SUB MAP
CSI MAP ADDRESS IS
PROGRAMMABLE AND SET BY
REGISTER 0xFE IN THE USER
SUB MAP
0x0E[6:5] = 00
0x0E[6:5] = 01
0x0E[6:5] = 10
USER
SUB MAP
INTERRUPT/VDP
SUB MAP
USER SUB
MAP 2
Figure 16. Register Map and Sub Map Access
Table 21. I2C Register Map and Sub Map Addresses
R/W Bit
ALSB Pin
Slave Address
0x40
0x41
0x40
0x41
0x40
0x41
0x42
0x43
0x42
0x43
0x42
0x43
0x84
0x85
0x88
0x89
SUB_USR_EN[1:0] Bits (Address 0x0E, Bits[6:5])
Register Map or Sub Map
0
0
0
0
0
0
1
1
1
1
1
1
X1
X1
X1
X1
0 (write)
1 (read)
0 (write)
1 (read)
0 (write)
1 (read)
0 (write)
1 (read)
0 (write)
1 (read)
0 (write)
1 (read)
0 (write)
1 (read)
0 (write)
1 (read)
00
00
01
01
10
10
00
00
01
01
10
10
XX1
XX1
XX1
XX1
User sub map
User sub map
Interrupt/VDP sub map
Interrupt/VDP sub map
User Sub Map 2
User Sub Map 2
User sub map
User sub map
Interrupt/VDP sub map
Interrupt/VDP sub map
User Sub Map 2
User Sub Map 2
VPP map
VPP map
CSI map (ADV7282A-M only)
CSI map (ADV7282A-M only)
1 X and XX mean don’t care.
Rev. A | Page 23 of 28
ADV7282A
Data Sheet
To reset the I2C slave address of the CSI map, write to the
CSI_TX_SLAVE_ADDR[7:1] bits in the user sub map (Address
0xFE, Bits[7:1]). Set these bits to a value of 0x88 (I2C write
address; I2C read address is 0x89).
VPP Map
The video postprocessor (VPP) map contains registers that
control the I2P core (interlaced to progressive converter).
The VPP map has a programmable I2C slave address, which is
programmed using Register 0xFD in the user sub map of the
main map. The default value for the VPP map address is 0x00;
however, the VPP map cannot be accessed until the I2C slave
address is reset. The recommended I2C slave address for the
VPP map is 0x84.
To reset the I2C slave address of the VPP map, write to the
VPP_SLAVE_ADDR[7:1] bits in the main register map
(Address 0xFD, Bits[7:1]). Set these bits to a value of 0x84 (I2C
write address; I2C read address is 0x85).
SUB_USR_EN[1:0] Bits, Address 0x0E, Bits[6:5]
The user sub map is available by default. The other two sub
maps are accessed using the SUB_USR_EN[1:0] bits. When
programming of the interrupt/VDP map or User Sub Map 2 is
completed, it is necessary to write to the SUB_USR_EN[1:0]
bits to return to the user sub map.
CSI Map (ADV7282A-M Only)
The CSI map contains registers that control the MIPI Tx output
stream from the ADV7282A-M.
The CSI map has a programmable I2C slave address, which is
programmed using Register 0xFE in the user sub map. The
default value for the CSI map address is 0x00; however, the CSI
map cannot be accessed until the I2C slave address is reset. The
recommended I2C slave address for the CSI map is 0x88.
Rev. A | Page 24 of 28
Data Sheet
ADV7282A
PCB LAYOUT RECOMMENDATIONS
The ADV7282A is a high precision, high speed, mixed-signal
device. To achieve maximum performance from the device, it is
important to use a well designed PCB. This section provides
guidelines for designing a PCB for use with the ADV7282A.
VREFN AND VREFP PINS
Place the circuit associated with the VREFN and VREFP pins
as close as possible to the ADV7282A and on the same side of
the PCB as the device.
ANALOG INTERFACE INPUTS
DIGITAL OUTPUTS
When routing the analog interface inputs on the PCB, keep
track lengths to a minimum. Use 75 Ω trace impedances when
possible; trace impedances other than 75 Ω increase the chance
of reflections.
INTRQ
The ADV7282A digital outputs are
, LLC, and P0 to P7.
INTRQ
The ADV7282A-M digital outputs are
to GPO2.
and GPO0
Minimize the trace length that the digital outputs must drive.
Longer traces have higher capacitance, requiring more current
and, in turn, causing more internal digital noise. Shorter traces
reduce the possibility of reflections.
POWER SUPPLY DECOUPLING
It is recommended that each power supply pin be decoupled with
100 nF and 10 nF capacitors. The basic principle is to place a
decoupling capacitor within approximately 0.5 cm of the PVDD
,
Adding a 30 Ω to 50 Ω series resistor can suppress reflections,
reduce EMI, and reduce current spikes inside the ADV7282A. If
using series resistors, place them as close as possible to the pins of
the ADV7282A. However, try not to add vias or extra length to
the output trace in an attempt to place the resistors closer.
AVDD, DVDD, and MVDD pins. Avoid placing the decoupling capa-
citors on the opposite side of the PCB from the ADV7282A
because doing so introduces inductive vias in the path.
Place the decoupling capacitors between the power plane and
the power pin. Current flows from the power plane to the
capacitor and then to the power pin. Do not apply the power
connection between the capacitor and the power pin. The best
approach is to place a via near, or beneath, the decoupling capaci-
tor pads down to the power plane (see Figure 17).
If possible, limit the capacitance that each digital output must
drive to less than 15 pF. This recommendation can be easily
accommodated by keeping traces short and by connecting the
outputs to only one device. Loading the outputs with excessive
capacitance increases the current transients inside the ADV7282A,
creating more digital noise on the power supplies.
VIA TO SUPPLY
VIA TO GND
SUPPLY
10nF
100nF
EXPOSED METAL PAD
GROUND
The ADV7282A has an exposed metal pad on the bottom of the
package. This pad must be soldered to ground. The exposed
pad is used for proper heat dissipation, noise suppression, and
mechanical strength.
Figure 17. Recommended Power Supply Decoupling
Ensure that the power supplies connected to the ADV7282A,
VDD and MVDD (MVDD only applies to the ADV7282A-M model)
DIGITAL INPUTS
P
in particular, are well regulated and filtered. For optimum
performance of the ADV7282A, it is recommended to isolate
each supply and to use decoupling on each pin, located as
physically close to the ADV7282A package as possible.
The digital inputs of the ADV7282A are designed to work with
1.8 V signals (3.3 V for DVDDIO) and are not tolerant of 5 V signals.
Extra components are required if 5 V logic signals must be applied
to the decoder.
Some graphic controllers use substantially different levels of
power when active (during active picture time) and when idle
(during horizontal and vertical sync periods). This disparity can
result in a measurable change in the voltage supplied to the analog
supply regulator, which can, in turn, produce changes in the regu-
lated analog supply voltage. This problem can be mitigated by
regulating the analog supply, or at least the PVDD supply, from a
different, cleaner power source, for example, from a 12 V supply.
MIPI Tx OUTPUTS (ADV7282A-M ONLY)
It is recommended that the MIPI Tx output traces be kept as short
as possible and on the same side of the PCB as the ADV7282A-M
device. It is also recommended that a solid plane (preferably a
ground plane) be placed on the layer adjacent to the MIPI Tx traces
to provide a solid reference plane.
MIPI Tx transmission operates in both differential and single-
ended modes. During high speed transmission, the pair of
outputs operates in differential mode; in low power mode, the
pair operates as two independent single-ended traces. There-
fore, it is recommended that each output pair be routed as two
loosely coupled 50 Ω single-ended traces to reduce the risk of
crosstalk between the two traces in low power mode.
Using a single ground plane for the entire board is also recom-
mended. Experience has shown that the noise performance is
the same or better with a single ground plane. Using multiple
ground planes can be detrimental because each separate ground
plane is smaller, and long ground loops can result.
Rev. A | Page 25 of 28
ADV7282A
Data Sheet
TYPICAL CIRCUIT CONNECTIONS
Figure 18 provides an example of how to connect the
ADV7282A. Figure 19 provides an example of how to connect
the ADV7282A-M.
See the XTAL data sheet (from the XTAL vendor), the AN-1260
Application Note, and the calculator tool (visit the design resources
section at www.analog.com/ADV7282A to download) for the
correct values for C1, C2, and RDAMP
.
For detailed schematics of the ADV7282A evaluation boards, visit
the ADV7282A product page at www.analog.com/ADV7282A.
1.8V
3.3V
1.8V
VDD_
VDD_
VIDDIO_
0.1µF
0.1µF 10nF
0.1µF
0.1µF
0.1µF
DIFF1+
IN
10nF
10nF
10nF
1.3kΩ
430Ω
430Ω
FULLY
DIFFERENTIAL
CVBS INPUT
150Ω
1.8V
0.1µF
VDD_
3.3V
VIDDIO_
IN
DIFF1–
1.3kΩ
1.8V
VDD_
0.1µF
9.1kΩ
1kΩ
1.8V
10nF
VDD_
0.1µF
0.1µF
17
DIFF2+
IN
IN
IN
IN
IN
1.3kΩ
430Ω
430Ω
18
12
11
10
9
75Ω
PSEUDO
DIFFERENTIAL
CVBS INPUT
22
24
IN
IN
IN
IN
IN
DIFF2–
8
7
1.3kΩ
9.1kΩ
25
23
6
5
1kΩ
ADV7282A
19
20
VREFP
VREFN
LOCATE VREFN AND VREFP CAPACITOR AS
CLOSE AS POSSIBLE TO THE ADV7282A AND ON
THE SAME SIDE OF THE PCB AS THE ADV7282A
0.1µF
32
26
INTRQ
INTRQ
XTAL CIRCUIT
14
C1
R
DAMP
28.63636MHz
15
C2
LOCATE AS CLOSE TO, AND ON THE SAME
SIDE OF THE PCB AS, THE ADV7282A
DVDIO
4kΩ
28
ALSB TIED HIGH: I2C ADDRESS = 0X42
ALSB TIED LOW: I2C ADDRESS = 0X40
31
PWRDWN
PWRDWN
RESET
27
30
29
RESET
SCLK
SCLK
SDATA
SDATA
Figure 18. ADV7282A Typical Connection Diagram
Rev. A | Page 26 of 28
Data Sheet
ADV7282A
1.8V
3.3V
VIDDIO_
1.8V
1.8V
VDD_
VDD_
VDD_
0.1µF
0.1µF
0.1µF
0.1µF
0.1µF
0.1µF
DIFF1+
IN
10nF
10nF
10nF
10nF
1.3kΩ
430Ω
430Ω
150Ω
FULLY
DIFFERENTIAL
CVBS INPUT
1.8V
VDD_
3.3V
VIDDIO_
IN
DIFF1–
1.8V
1.3kΩ
9.1kΩ
VDD_
1.8V
VDD_
0.1µF
1.8V
VDD_
10nF
1kΩ
0.1µF
0.1µF
17
18
DIFF2+
IN
IN
IN
IN
IN
1.3kΩ
430Ω
430Ω
9
75Ω
PSEUDO
DIFFERENTIAL
CVBS INPUT
10
22
IN
DIFF2–
1.3kΩ
9.1kΩ
11
12
23
24
CLKP
CLKN
IN
IN
IN
IN
1kΩ
ADV7282A-M
25
0.1µF
SINGLE-ENDED
CVBS INPUT
EXAMPLE
IN
26
27
24Ω
IN
IN
IN
IN
51Ω
6
7
8
0.1µF
SINGLE-ENDED
CVBS INPUT
EXAMPLE
XTAL CIRCUIT
IN
24Ω
14
51Ω
C1
R
DAMP
28.63636MHz
5
15
INTRQ
INTRQ
C2
LOCATE AS CLOSE TO, AND ON THE SAME
SIDE OF THE PCB AS, THE ADV7282A-M
LOCATE VREFN AND VREFP CAPACITOR AS CLOSE
AS POSSIBLE TO THE ADV7282A-M AND ON THE
SAME SIDE OF THE PCB AS THE ADV7282A-M
DVDIO
29
4kΩ
19
VREFP
VREFN
ALSB TIED HIGH: I2C ADDRESS = 0X42
ALSB TIED LOW: I2C ADDRESS = 0X40
0.1µF
20
32
PWRDWN
PWRDWN
RESET
28
31
30
RESET
SCLK
SCLK
SDATA
SDATA
Figure 19. ADV7282A-M Typical Connection Diagram
Rev. A | Page 27 of 28
ADV7282A
Data Sheet
OUTLINE DIMENSIONS
5.10
0.30
0.25
0.18
5.00 SQ
4.90
PIN 1
INDICATOR
PIN 1
INDICATOR
25
32
24
1
0.50
BSC
*
3.75
EXPOSED
PAD
3.60 SQ
3.55
17
8
16
9
0.50
0.40
0.30
0.25 MIN
TOP VIEW
BOTTOM VIEW
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
0.80
0.75
0.70
0.05 MAX
0.02 NOM
SECTION OF THIS DATA SHEET.
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
*
COMPLIANT TO JEDEC STANDARDS MO-220-WHHD-5
WITH THE EXCEPTION OF THE EXPOSED PAD DIMENSION.
Figure 20. 32-Lead Lead Frame Chip Scale Package [LFCSP]
5 mm × 5 mm Body and 0.75 mm Package Height
(CP-32-12)
Dimensions shown in millimeters
ORDERING GUIDE
Model1, 2
Temperature Range
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
Package Description
Package Option
CP-32-12
CP-32-12
CP-32-12
CP-32-12
ADV7282AWBCPZ
ADV7282AWBCPZ-RL
ADV7282AWBCPZ-M
ADV7282AWBCPZ-M-RL
EVAL-ADV7282AEBZ
EVAL-ADV7282AMEBZ
32-Lead Lead Frame Chip Scale Package [LFCSP]
32-Lead Lead Frame Chip Scale Package [LFCSP]
32-Lead Lead Frame Chip Scale Package [LFCSP]
32-Lead Lead Frame Chip Scale Package [LFCSP]
Evaluation Board for the ADV7282A
Evaluation Board for the ADV7282A-M
1 Z = RoHS Compliant Part.
2 W = Qualified for Automotive Applications.
AUTOMOTIVE PRODUCTS
The ADV7282AW models are available with controlled manufacturing to support the quality and reliability requirements of automotive
applications. Note that these automotive models may have specifications that differ from the commercial models; therefore, designers should
review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for use in automotive
applications. Contact your local Analog Devices account representative for specific product ordering information and to obtain the specific
Automotive Reliability reports for these models.
I2C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors).
©2017–2018 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D16148-0-5/18(A)
Rev. A | Page 28 of 28
相关型号:
EVAL-ADV7282MEBZ
10-Bit, 4 Oversampled SDTV Video Decoder with Differential Inputs and Deinterlacer
ADI
EVAL-ADV7400AEBM
10-Bit Intergrated Multiformat SDTV/HDTV Video Decoder and RGB Graphics Digitizer
ADI
©2020 ICPDF网 联系我们和版权申明