EVAL-ADV7322EB_技术文档

Multiformat 11-Bit

HDTV Video Encoder

Preliminary Technical Data

ADV7322

FEATURES

GENERAL FEATURES

High definition input formats

16-, 24-bit (4:2:2, 4:4:4) parallel YCrCb

Fully compliant with

SMPTE 274M (1080i, 1080p @ 74.25 MHz)

SMPTE 296M (720p)

SMPTE 240M (1035i)

RGB in 3- × 8-bit 4:4:4 input format

HDTV RGB supported

RGB, RGBHV

Other high definition formats using async

timing mode

Enhanced definition input formats

8-, 16-, 24-bit (4:2:2, 4:4:4) parallel YCrCb

SMPTE 293M (525p)

Simultaneous SD/HD, PS/SD inputs and outputs

Oversampling up to 216 MHz

Programmable DAC gain control

Sync outputs in all modes

On-board voltage reference

Six 11-bit precision video DACs

2-wire serial I²C® interface, open-drain configuration

Dual I/O supply 2.5 V/3.3 V operation

Analog and digital supply 2.5 V

On-board PLL

64-lead LQFP package

Lead (Pb)-free product

APPLICATIONS

BTA T-1004 EDTV2 (525p)

EVD players (enhanced versatile disk)

SD/PS DVD recorders/players

SD/progressive scan/HDTV display devices

SD/HDTV set top boxes

ITU-R BT.1358 (625p/525p)

ITU-R BT.1362 (625p/525p)

RGB in 3- × 8-bit 4:4:4 input format

Standard definition input formats

CCIR-656 4:2:2 8-bit or 16-bit parallel input

High definition output formats

YPrPb HDTV (EIA 770.3)

STANDARD DEFINITION

CONTROL BLOCK

ADV7322

COLOR CONTROL

BRIGHTNESS

DNR

GAMMA

11-BIT

DAC

PROGRAMMABLE

FILTERS

11-BIT

DAC

O

V

E

R

S

A

M

P

L

SD TEST PATTERN

RGB, RGBHV

CGMS-A (720p/1080i)

D

E

M

U

X

11-BIT

DAC

Y7–Y0

C7–C0

S7–S0

PROGRAMMABLE

RGB MATRIX

Enhanced definition output formats

Macrovision Rev 1.2 (525p/625p)

CGMS-A (525p/625p)

11-BIT

DAC

I

N

G

HIGH DEFINITION

CONTROL BLOCK

11-BIT

DAC

YPrPb progressive scan (EIA-770.1, EIA-770.2)

RGB, RGBHV

Standard definition output formats

Composite NTSC M/N

Composite PAL M/N/B/D/G/H/I, PAL-60

SMPTE 170M NTSC-compatible composite video

ITU-R BT.470 PAL-compatible composite video

S-video (Y/C)

HD TEST PATTERN

11-BIT

DAC

COLOR CONTROL

ADAPTIVE FILTER CTRL

SHARPNESS FILTER

HSYNC

VSYNC

BLANK

TIMING

GENERATOR

2

I C

INTERFACE

CLKIN_A

CLKIN_B

PLL

Figure 1. Simplified Functional Block Diagram

GENERAL DESCRIPTION

EuroScart RGB

Component YPrPb (Betacam, MII, SMPTE/EBU N10)

Macrovision Rev 7.1.L1

CGMS/WSS

Closed captioning

The ADV®7322 is a high speed, digital-to-analog encoder on a

single monolithic chip. It includes six high speed video DACs

with TTL compatible inputs. It has separate 8-, 16-, 24-bit input

ports that accept data in high definition and/or standard

definition video format. For all standards, external horizontal,

vertical, and blanking signals or EAV/SAV timing codes control

the insertion of appropriate synchronization signals into the

digital data stream and therefore the output signal.

Rev. PrA

Information furnished by Analog Devices is believed to be accurate and reliable.

However, no responsibility is assumed by Analog Devices for its use, nor for any

infringements of patents or other rights of third parties that may result from its use.

Specifications subject to change without notice. No license is granted by implication

or otherwise under any patent or patent rights of Analog Devices. Trademarks and

registered trademarks are the property of their respective owners.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.

Tel: 781.329.4700

Fax: 781.326.8703

www.analog.com

ADV7322

Preliminary Technical Data

TABLE OF CONTENTS

Specifications..................................................................................... 6

HD Sharpness Filter and Adaptive Filter Controls................ 56

Dynamic Specifications ................................................................... 7

Timing Specifications....................................................................... 8

Timing Diagrams.............................................................................. 9

Absolute Maximum Ratings.......................................................... 17

Thermal Characteristics ............................................................ 17

Pin Configuration and Function Descriptions........................... 18

Typical Performance Characteristics ........................................... 20

MPU Port Description................................................................... 24

Register Access................................................................................ 26

Register Programming............................................................... 26

Subaddress Register (SR7 to SR0) ............................................ 26

Input Configuration ....................................................................... 39

Standard Definition Only.......................................................... 39

Progressive Scan Only or HDTV Only ................................... 39

HD Sharpness Filter and Adaptive Filter Application

Examples...................................................................................... 57

SD Digital Noise Reduction...................................................... 58

Coring Gain Border ................................................................... 59

Coring Gain Data....................................................................... 59

DNR Threshold .......................................................................... 59

Border Area................................................................................. 59

Block Size Control...................................................................... 59

DNR Input Select Control......................................................... 59

DNR Mode Control ................................................................... 60

Block Offset Control.................................................................. 60

SD Active Video Edge ................................................................ 60

SAV/EAV Step Edge Control.................................................... 60

Board Design and Layout.............................................................. 62

DAC Termination and Layout Considerations ...................... 62

Video Output Buffer and Optional Output Filter.................. 62

PCB Board Layout...................................................................... 63

Appendix 1—Copy Generation Management System .............. 65

PS CGMS..................................................................................... 65

HD CGMS................................................................................... 65

SD CGMS .................................................................................... 65

Function of CGMS Bits ............................................................. 65

CGMS Functionality.................................................................. 65

Appendix 2—SD Wide Screen Signaling..................................... 68

Appendix 3—SD Closed Captioning........................................... 69

Appendix 4—Test Patterns............................................................ 70

Appendix 5—SD Timing Modes.................................................. 73

Simultaneous Standard Definition and Progressive Scan or

HDTV .......................................................................................... 39

Progressive Scan at 27 MHz (Dual Edge) or 54 MHz ........... 40

Features ............................................................................................ 42

Output Configuration................................................................ 42

HD Async Timing Mode ........................................................... 43

HD Timing Reset........................................................................ 44

SD Real-Time Control, Subcarrier Reset, and Timing Reset 44

Reset Sequence............................................................................ 46

SD VCR FF/RW Sync................................................................. 46

Vertical Blanking Interval ......................................................... 47

Subcarrier Frequency Registers................................................ 47

Square Pixel Timing Mode........................................................ 48

Filters............................................................................................ 49

Color Controls and RGB Matrix .............................................. 50

Programmable DAC Gain Control .......................................... 54

Gamma Correction .................................................................... 54

Mode 0 (CCIR-656)—Slave Option (Timing Register 0 TR0 =

X X X X X 0 0 0) ......................................................................... 73

Mode 0 (CCIR-656)—Master Option (Timing Register 0 TR0

= X X X X X 0 0 1)...................................................................... 74

Rev. PrA | Page 2 of 88

Preliminary Technical Data

ADV7322

Mode 1—Slave Option (Timing Register 0 TR0 = X X X X X

0 1 0) .............................................................................................76

Appendix 6—HD Timing ..............................................................81

Appendix 7—Video Output Levels...............................................82

HD YPrPb Output Levels...........................................................82

RGB Output Levels .....................................................................83

YPrPb Levels—SMPTE/EBU N10............................................84

Appendix 8—Video Standards......................................................86

Outline Dimensions........................................................................88

Ordering Guide ...........................................................................88

Mode 1—Master Option (Timing Register 0 TR0 = X X X X

X 0 1 1)..........................................................................................77

Mode 2— Slave Option (Timing Register 0 TR0 = X X X X X

1 0 0) .............................................................................................78

Mode 2—Master Option (Timing Register 0 TR0 = X X X X

X 1 0 1)..........................................................................................79

Mode 3—Master/Slave Option (Timing Register 0 TR0 = X

X X X X 1 1 0 or X X X X X 1 1 1) ...........................................80

REVISION HISTORY

9/04—PrA: Preliminary Version

Rev. PrA | Page 3 of 88

ADV7322

Preliminary Technical Data

Table 1. Standards Directly Supported¹

DETAILED FEATURES

CLK

Input

(MHz)

High definition programmable features (720p/1080i/1035i)

2× oversampling (148.5 MHz)

Internal test pattern generator

Color hatch, black bar, flat field/frame

Fully programmable YCrCb to RGB matrix

Gamma correction

Interlace/ Frame

Resolution Prog. Rate (Hz)

29.97

Standard

720 × 480

720 × 576

720 × 480

I

27

24.54

ITU-R BT.656

NTSC

25

29.97

Square Pixel

Programmable adaptive filter control

Programmable sharpness filter control

CGMS-A (720p/1080i)

Enhanced definition programmable features (525p/625p)

8× oversampling (216 MHz output)

Internal test pattern generator

Color hatch, black bar, flat frame

Individual Y and PrPb output delay

Gamma correction

Programmable adaptive filter control

Fully programmable YCrCb to RGB matrix

Undershoot limiter

Macrovision Rev 1.2 (525p/625p)

CGMS-A (525p/625p)

Standard definition programmable features

16× oversampling (216 MHz)

Internal test pattern generator

Color bars, black bar

Controlled edge rates for start and end of active video

Individual Y and PrPb output delay

Undershoot limiter

720 × 576

720 × 483

I

25

29.5

27

PAL Square

Pixel

SMPTE

293M

BTA T-1004

ITU-R

BT.1358

ITU-R

BT.1358

ITU-R

BT.1362

ITU-R

BT.1362

SMPTE

240M

P

59.94

720 × 483

P

59.94

27

720 × 576

720 × 483

720 × 576

1920 × 1035

P

I

50

27

59.94

50

30

29.97

60, 50, 30,

25, 24,

23.97,

59.94,

29.97

30, 25

29.97

30, 25, 24

23.98,

29.97,

74.25

74.1758

74.25,

1280 × 720

P

SMPTE

296M

74.1758

1920 × 1080

I

74.25

74.1758

74.25

SMPTE

274M

P

SMPTE

274M

Gamma correction

Digital noise reduction (DNR)

74.1758

Multiple chroma and luma filters

Luma-SSAF™ filter with programmable gain/attenuation

PrPb SSAF™

¹Other standards are supported in async timing mode.

Separate pedestal control on component and

composite/S-video output

VCR FF/RW sync mode

Macrovision Rev 7.1.L1

CGMS/WSS

Closed captioning

Rev. PrA | Page 4 of 88

Preliminary Technical Data

ADV7322

HD PIXEL

INPUT

SHARPNESS

AND

Y

CR

CB

Y COLOR

CR COLOR

CB COLOR

DE-

TEST

DAC

4:2:2

TO

4:4:4

INTER-

LEAVE

ADAPTIVE

FILTER

PS 8×

PATTERN

HDTV 2×

CLKIN_B

CONTROL

P_HSYNC

P_VSYNC

P_BLANK

TIMING

GENERATOR

CLOCK

CONTROL

AND PLL

U

V

UV SSAF

S_HSYNC

S_VSYNC

S_BLANK

RGB

TIMING

GENERATOR

MATRIX

SD 16×

CLKIN_A

CB

CR

Y

DE-

INTER-

LEAVE

LUMA

AND

F

TEST

PATTERN

DNR

GAMMA

COLOR

CONTROL

SYNC

INSERTION

SC

2× OVER-

SAMPLING

CGMS

WSS

MODU-

LATION

CHROMA

FILTERS

SD PIXEL

INPUT

Figure 2. Detailed Functional Block Diagram

TERMINOLOGY

SD: standard definition video, conforming to

ITU-R BT.601/ITU-R BT.656.

HDTV: high definition television video, conforming to SMPTE

274M, or SMPTE 296M and SMPTE240M.

HD: high definition video, i.e., 720p/1080i/1035i.

EDTV: enhanced definition television (525p/625p)

YCrCb SD, PS, or HD component: digital video.

YPrPb SD, PS, or HD component: analog video.

PS: progressive scan video, conforming to SMPTE 293M,

ITU-R BT.1358, BTAT-1004EDTV2, or ITU-R BT.13621362.

Rev. PrA | Page 5 of 88

ADV7322

Preliminary Technical Data

SPECIFICATIONS

V_AA= 2.375 V − 2.625 V, V_DD= 2.375 V − 2.625 V, V_{DD_IO}= 2.375 V − 3.6 V, V_REF= 1.235 V, R_SET= 3040 Ω, R_LOAD= 300 Ω. All specifications

T_MINto T_MAX(0°C to 70°C), unless otherwise noted.

Table 2.

Parameter

STATIC PERFORMANCE¹

Min

Typ

Max

Unit

Test Conditions

Resolution

Integral Nonlinearity

Differential Nonlinearity², +ve

Differential Nonlinearity², −ve

DIGITAL OUTPUTS

Output Low Voltage, V_OL

Output High Voltage, V_OH

Three-State Leakage Current

Three-State Output Capacitance

DIGITAL AND CONTROL INPUTS

Input High Voltage, V_IH

Input Low Voltage, V_IL

Input Leakage Current

Input Capacitance, C_IN

ANALOG OUTPUTS

11

Bits

LSB

1.5

0.5

1.0

0.4 [0.4]³

V

µA

pF

I_SINK= 3.2 mA

I_SOURCE= 400 µA

V_IN= 0.4 V, 2.4 V

2.4[2.0]³

1.0

2

V

µA

pF

0.8

10

2

V_IN= 2.4 V

Full-Scale Output Current

Output Current Range

DAC to DAC Matching

Output Compliance Range, V_OC

Output Capacitance, C_OUT

VOLTAGE REFERENCE

Internal Reference Range, V_REF

External Reference Range, V_REF

V_REFCurrent⁴

4.1

4.33

1.0

7

4.6

mA

%

V

pF

0

1.4

1.15

1.235

10

1.3

V

µA

POWER REQUIREMENTS

Normal Power Mode

5

I_DD

137

78

73

140

1.0

37

mA

SD only [16×]

PS only [8×]

HDTV only [2×]

SD[16×, 8 bit] + PS[8×, 16 bit]

190⁶

45

I_{DD_IO}

7, 8

I_AA

Sleep Mode

I_DD

80

µA

I_AA

7

µA

I_{DD_IO}

250

0.01

µA

POWER SUPPLY REJECTION RATIO

%/%

¹Oversampling disabled. Static DAC performance will be improved with increased oversampling ratios.

²DNL measures the deviation of the actual DAC output voltage step from the ideal. For +ve DNL, the actual step value lies above the ideal step value; for −ve DNL, the

actual step value lies below the ideal step value.

³Value in brackets for V_{DD_IO}= 2.375 V − 2.75 V.

⁴External current required to overdrive internal V_REF

.

⁵I_DD, the circuit current, is the continuous current required to drive the digital core.

⁶Guaranteed maximum by characterization.

⁷All DACs on.

⁸I_AAis the total current required to supply all DACs including the V_REFcircuitry and the PLL circuitry.

Rev. PrA | Page 6 of 88

Preliminary Technical Data

DYNAMIC SPECIFICATIONS

ADV7322

V_AA= 2.375 V − 2.625 V, V_DD= 2.375 V − 2.625 V, V_{DD_IO}= 2.375 V − 3.6 V, V_REF= 1.235 V, R_SET= 3040 Ω, R_LOAD= 300 Ω. All specifications

T_MINto T_MAX(0°C to 70°C), unless otherwise noted.

Table 3.

Parameter

Min

Typ

Max

Unit

Test Conditions

PROGRESSIVE SCAN MODE

Luma Bandwidth

Chroma Bandwidth

SNR

12.5

5.8

65.6

72

MHz

dB

Luma ramp unweighted

Flat field full bandwidth

dB

HDTV MODE

Luma Bandwidth

30

13.75

MHz

Chroma Bandwidth

STANDARD DEFINITION MODE

Hue Accuracy

0.4

Degrees

Color Saturation Accuracy

Chroma Nonlinear Gain

Chroma Nonlinear Phase

Chroma/Luma Intermodulation

Chroma/Luma Gain Inequality

Chroma/Luma Delay Inequality

Luminance Nonlinearity

Chroma AM Noise

0.4

1.2

−0.2

0

97

−1.1

0.5

84

%

Referenced to 40 IRE

Degrees

%

ns

%

dB

Chroma PM Noise

Differential Gain

Differential Phase

SNR

75.2

0.15

0.2

59.1

77.1

dB

%

Degrees

dB

NTSC

Luma ramp

Flat field full bandwidth

Rev. PrA | Page 7 of 88

ADV7322

Preliminary Technical Data

TIMING SPECIFICATIONS

V_AA= 2.375 V − 2.625 V, V_DD= 2.375 V − 2.625 V, V_{DD_IO}= 2.375 V − 3.6 V, V_REF= 1.235 V, R_SET= 3040 Ω, R_LOAD= 300 Ω. All specifications

T_MINto T_MAX(0°C to 70°C), unless otherwise noted.

Table 4.

Parameter

Min

Typ

Max

Unit

Test Conditions

MPU PORT¹

SCLOCK Frequency

0

400

kHz

µs

SCLOCK High Pulse Width, t₁

SCLOCK Low Pulse Width, t₂

Hold Time (Start Condition), t₃

0.6

1.3

0.6

µs

First clock generated after this period relevant

for repeated start condition

Setup Time (Start Condition), t₄

Data Setup Time, t₅

SDATA, SCLOCK Rise Time, t₆

SDATA, SCLOCK Fall Time, t₇

Setup Time (Stop Condition), t₈

RESET Low Time

0.6

100

µs

ns

µs

ns

300

0.6

100

ANALOG OUTPUTS

Analog Output Delay²

Output Skew

7

1

ns

CLOCK CONTROL AND PIXEL PORT³

f_CLK

29.5

MHz

SD PAL square pixel mode

PS/HD async mode

81

Clock High Time, t₉

Clock Low Time, t₁₀

40

2.0

% of one clk cycle

ns

1

Data Setup Time, t₁₁

1

Data Hold Time, t₁₂

SD Output Access Time, t₁₃

SD Output Hold Time, t₁₄

HD Output Access Time, t₁₃

HD Output Hold Time, t₁₄

PIPELINE DELAY⁴

15

14

ns

5.0

63

76

35

41

36

clk cycles

SD [2×, 16×]

SD component mode [16×]

PS [1×]

PS [8×]

HD [2×, 1×]

¹Guaranteed by characterization.

²Output delay measured from the 50% point of the rising edge of CLOCK to the 50% point of DAC output full-scale transition.

³Data: C[9:0]; Y[9:0], S[9:0]

P_HSYNC P_VSYNC P_BLANK S_HSYNC S_VSYNC S_BLANK

Control:

,

⁴SD, PS = 27 MHz, HD = 74.25 MHz.

Rev. PrA | Page 8 of 88

Preliminary Technical Data

TIMING DIAGRAMS

ADV7322

CLKIN_A

t₉

t₁₂

t

10

P_HSYNC,

CONTROL

P_VSYNC,

INPUTS

P_BLANK

Y7–Y0

C7–C0

Y0

Y1

Y2

Y3

Y4

Y5

Cb0

Cr0

Cr4

Cb4

Cb2

Cr2

t₁₁

t₁₃

CONTROL

OUTPUTS

t₁₄

t₉= CLOCK HIGH TIME

t₁₀= CLOCK LOW TIME

t₁₁= DATA SETUP TIME

t₁₂= DATA HOLD TIME

Figure 3. HD Only 4:2:2 Input Mode [Input Mode 010]; PS Only 4:2:2 Input Mode [Input Mode 001]

CLKIN_A

t₉

t₁₀

t₁₂

P_HSYNC,

P_VSYNC,

P_BLANK

CONTROL

INPUTS

Y7–Y0

C7–C0

Y0

Y1

Y2

Y3

Y4

Y5

Cb1

t₁₁

Cb2

Cr2

Cb3

Cb4

Cb5

Cb0

Cr1

Cr3

Cr4

Cr5

S7–S0

Cr0

CONTROL

OUTPUTS

t₁₄

t₁₃

t₉= CLOCK HIGH TIME

t₁₀= CLOCK LOW TIME

t₁₁= DATA SETUP TIME

t₁₂= DATA HOLD TIME

Figure 4. HD Only 4:4:4 Input Mode [Input Mode 010]; PS Only 4:4:4 Input Mode [Input Mode 001]

Rev. PrA | Page 9 of 88

ADV7322

Preliminary Technical Data

CLKIN_A

t₉

t₁₂

t₁₀

P_HSYNC,

P_VSYNC,

P_BLANK

CONTROL

INPUTS

Y7–Y0

C7–C0

G0

B0

G1

B1

G2

G3

B3

G4

B4

G5

B5

B2

R2

t₁₁

S7–S0

R0

R1

R3

R4

R5

CONTROL

OUTPUTS

t₁₄

t₁₃

t₉= CLOCK HIGH TIME

t₁₀= CLOCK LOW TIME

t₁₁= DATA SETUP TIME

t₁₂= DATA HOLD TIME

Figure 5. HD RGB 4:4:4 Input Mode [Input Mode 010]

CLKIN_B*

t

9

t₁₀

P_HSYNC,

P_VSYNC,

P_BLANK

CONTROL

INPUTS

Crxxx

Yxxx

Cr0

Y1

Y7–Y0

Cb0

Y0

t₁₂

t₁₁

t₁₃

CONTROL

OUTPUTS

t₁₄

t₉= CLOCK HIGH TIME

t₁₀= CLOCK LOW TIME

t₁₁= DATA SETUP TIME

t₁₂= DATA HOLD TIME

*CLKIN_B MUST BE USED IN THIS PS MODE.

HSYNC VSYNC

Input Mode [Input Mode 100]

Figure 6. PS 4:2:2 8-Bit Interleaved at 27 MHz

/

Rev. PrA | Page 10 of 88

Preliminary Technical Data

ADV7322

CLKIN_A

t₁₀

t₉

P_VSYNC,

P_HSYNC,

P_BLANK

CONTROL

INPUTS

Crxxx

Cb0

Y0

Cr0

Y1

Yxxx

Y7–Y0

t₁₂

t₁₃

t₁₄

t₁₁

CONTROL

OUTPUTS

t₉= CLOCK HIGH TIME

t₁₀= CLOCK LOW TIME

t₁₁= DATA SETUP TIME

t₁₂= DATA HOLD TIME

HSYNC VSYNC

/

Figure 7. PS 4:2:2 8-Bit Interleaved at 54 MHz

Input Mode [Input Mode 111]

CLKIN_B*

t₉

t₁₀

Y7–Y0

FF

00

XY

Cb0

Y0

Cr0

Y1

t12

t₁₂

t₁₁

t₁₃

CONTROL

OUTPUTS

t₁₄

t₉= CLOCK HIGH TIME

t₁₀= CLOCK LOW TIME

t₁₁= DATA SETUP TIME

t₁₂= DATA HOLD TIME

*CLKIN_B USED IN THIS PS ONLY MODE.

Figure 8. PS Only 4:2:2 8-Bit Interleaved at 27 MHz EAV/SAV Input Mode [Input Mode 100]

Rev. PrA | Page 11 of 88

ADV7322

Preliminary Technical Data

CLKIN_A

Y7–Y0

t₁₀

t₉

FF

00

XY

Cb0

Y0

Y1

Cr0

t₁₂

t₁₃

t₁₄

t₁₁

CONTROL

OUTPUTS

t₉= CLOCK HIGH TIME

t₁₀= CLOCK LOW TIME

t₁₁= DATA SETUP TIME

t₁₂= DATA HOLD TIME

NOTE: Y0, Cb0 SEQUENCE AS PER SUBADDRESS 0x01 BIT-1

Figure 9. PS Only 4:2:2 8-Bit Interleaved at 54 MHz EAV/SAV Input Mode [Input Mode 111]

CLKIN_B

t₁₂

t₁₀

t₉

P_HSYNC,

P_VSYNC,

P_BLANK

CONTROL

INPUTS

HD INPUT

Y7–Y0

C7–C0

Y0

Y1

Y3

Y4

Y5

Y2

Cr0

Cr4

Cb0

Cb2

Cr2

Cb4

t₁₁

CLKIN_A

t₁₂

t₉

t₁₀

S_HSYNC,

S_VSYNC,

S_BLANK

CONTROL

INPUTS

SD INPUT

S7–S0

Cr0

Y1

Cb0

Y0

Cb1

Y2

t₁₁

Figure 10. HD 4:2:2 and SD (8-Bit) Simultaneous Input Mode [Input Mode 101: SD Oversampled] [Input Mode 110: HD Oversampled]

Rev. PrA | Page 12 of 88

Preliminary Technical Data

ADV7322

CLKIN_B

t₁₂

t₁₀

t₉

P_HSYNC,

P_VSYNC,

P_BLANK

CONTROL

INPUTS

PS INPUT

Y7–Y0

C7–C0

Y0

Y1

Y3

Y4

Y5

Y2

Cr0

Cr4

Cb0

Cb2

Cr2

Cb4

t₁₁

CLKIN_A

t₁₂

t₉

t₁₀

S_HSYNC,

S_VSYNC,

S_BLANK

CONTROL

INPUTS

SD INPUT

S7–S0

Cr0

Y1

Cb0

Y0

Cb1

Y2

t₁₁

Figure 11. PS (4:2:2) and SD (8-Bit) Simultaneous Input Mode [Input Mode 011]

CLKIN_B

t₉

t₁₀

P_HSYNC,

P_VSYNC,

P_BLANK

CONTROL

INPUTS

PS INPUT

Crxxx

Yxxx

Cr0

Y1

Y7–Y0

Cb0

Y0

t₁₂

t₁₁

CLKIN_A

t₁₂

t₉

t₁₀

S_HSYNC,

S_VSYNC,

S_BLANK

CONTROL

INPUTS

SD INPUT

S7–S0

Cr0

Y1

Cb0

Y0

Cb1

Y2

t₁₁

Figure 12. PS (8-Bit) and SD (8-Bit) Simultaneous Input Mode [Input Mode 100]

Rev. PrA | Page 13 of 88

ADV7322

Preliminary Technical Data

CLKIN_A

t₉

t₁₂

t10

S_HSYNC,

S_VSYNC,

S_BLANK

CONTROL

INPUTS

IN SLAVE MODE

S7–S0/Y7–Y0*

Cb0

Cr0

Cb4

Cr4

Cb2

Cr2

t₁₁

t₁₃

CONTROL

OUTPUTS

IN MASTER/SLAVE MODE

t₁₄

*SELECTED BY ADDRESS 0x01 BIT 7

Figure 13. 8-Bit SD Only Pixel Input Mode [Input Mode 000]

CLKIN_A

t₉

t₁₂

t₁₀

S_HSYNC,

S_VSYNC,

S_BLANK

CONTROL

INPUTS

IN SLAVE MODE

S7–S0/Y7–Y0*

C7–C0*

Y0

Y1

Y2

Y3

Cb0

Cr0

Cb2

Cr2

t₁₁

t₁₃

CONTROL

OUTPUTS

IN MASTER/SLAVE MODE

t₁₄

*SELECTED BY ADDRESS 0x01 BIT 7: See Table 21.

Figure 14. 16-Bit SD Only Pixel Input Mode [Input Mode 000]

Rev. PrA | Page 14 of 88

Preliminary Technical Data

ADV7322

P_HSYNC

P_VSYNC

a

P_BLANK

Y2

Y3

Y7–Y0

C7–C0

Y0

Y1

Cb0 Cr0 Cr1 Cb1

b

a AND b AS PER RELEVANT STANDARD

Figure 15. HD 4:2:2 Input Timing Diagram

P_HSYNC

P_VSYNC

a

P_BLANK

Cr

Y

Y7–Y0

Cb

Y

b

a = 32 CLKCYCLES FOR 525p

a = 24 CLKCYCLES FOR 625p

AS RECOMMENDED BY STANDARD

b(MIN) = 244 CLKCYCLES FOR 525p

b(MIN) = 264 CLKCYCLES FOR 625p

Figure 16. PS 4:2:2 8-Bit Interleaved Input Timing Diagram

Rev. PrA | Page 15 of 88

ADV7322

Preliminary Technical Data

S_HSYNC

S_VSYNC

PAL = 24 CLK CYCLES

NTSC = 32 CLK CYCLES

S_BLANK

Cr

Y

S7–S0/Y7–Y0*

Cb

Y

PAL = 24 CLK CYCLES

NTSC = 32 CLK CYCLES

*SELECTED BY ADDRESS 0x01 BIT 7

Figure 17. SD Timing Input for Timing Mode 1

t₃

t₅

t₃

SDA

t₁

t₆

SCLK

t₄

t₂

t₇

t₈

Figure 18. MPU Port Timing Diagram

Rev. PrA | Page 16 of 88

Preliminary Technical Data

ADV7322

ABSOLUTE MAXIMUM RATINGS

Table 5.

Parameter¹

Value

Stresses above those listed under Absolute Maximum Ratings

may cause permanent damage to the device. This is a stress

rating only; functional operation of the device at these or any

other conditions above those listed in the operational sections

of this specification is not implied. Exposure to absolute

maximum rating conditions for extended periods may affect

device reliability.

V_AAto AGND

V_DDto DGND

−0.3 V to +3.0 V

−0.3 V to 4.6 V

−0.3 V to V_{DD_IO}+0.3 V

−0.3 V to +0.3 V

V_{DD_IO}to GND_IO

Digital Input Voltage to DGND

V_AAto V_DD

AGND to DGND

DGND to GND_IO

AGND to GND_IO

Ambient Operating Temperature (T_A) 0°C to 70°C

Storage Temperature (T_S)

Infrared Reflow Soldering (20 s)

–65°C to +150°C

260°C

THERMAL CHARACTERISTICS

θ_JC= 11°C/W

θ_JA= 47°C/W

The ADV7322 is a Pb-free environmentally friendly product. It

is manufactured using the most up-to-date materials and

processes. The coating on the leads of each device is 100% pure

Sn electroplate. The device is suitable for Pb-free applications

and is able to withstand surface-mount soldering at up to 255°C

( 5°C).

In addition, it is backward-compatible with conventional SnPb

soldering processes. This means that the electroplated Sn

coating can be soldered with Sn/Pb solder pastes at

conventional reflow temperatures of 220°C to 235°C.

¹Analog output short circuit to any power supply or common can be of

an indefinite duration.

ESD CAUTION

ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily

accumulate on the human body and test equipment and can discharge without detection. Although

this product features proprietary ESD protection circuitry, permanent damage may occur on devices

subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are

recommended to avoid performance degradation or loss of functionality.

Rev. PrA | Page 17 of 88

ADV7322

Preliminary Technical Data

PIN CONFIGURATION AND FUNCTION DESCRIPTIONS

64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49

1

48

S_BLANK

V

DD_IO

PIN 1

2

3

47

46

45

44

43

42

41

40

39

38

37

36

35

34

33

TEST0

TEST1

Y0

R

SET1

V

REF

4

COMP1

DAC A

DAC B

DAC C

5

Y1

6

Y2

ADV7322

TOP VIEW

(Not to Scale)

7

Y3

8

Y4

V

AA

9

Y5

AGND

DAC D

DAC E

DAC F

COMP2

10

11

12

13

14

15

16

V

DD

DGND

Y6

Y7

TEST2

TEST3

C0

R

SET2

EXT_LF

RESET

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

Figure 19. Pin Configuration

Rev. PrA | Page 18 of 88

Preliminary Technical Data

ADV7322

Table 6. Pin Function Descriptions

Mnemonic

Input/Output Function

DGND

AGND

CLKIN_A

CLKIN_B

G

I

Digital Ground.

Analog Ground.

Pixel Clock Input for HD (74.25 MHz Only, PS Only (27 MHz), SD Only (27 MHz).

Pixel Clock Input. Requires a 27 MHz reference clock for progressive scan mode or a 74.25 MHz (74.1758

MHz) reference clock in HDTV mode. This clock is only used in dual modes.

I

COMP1,

COMP2

O

Compensation Pin for DACs. Connect 0.1 µF capacitor from COMP pin to V_AA.

DAC A

DAC B

DAC C

DAC D

O

CVBS/Green/Y/Y Analog Output.

Chroma/Blue/U/Pb Analog Output.

Luma/Red/V/Pr Analog Output.

In SD Only Mode: CVBS/Green/Y Analog Output; in HD Only Mode and Simultaneous HD/SD Mode:

Y/Green [HD] Analog Output.

DAC E

DAC F

O

In SD Only Mode: Luma/Blue/U Analog Output; in HD Only Mode and Simultaneous HD/SD Mode: Pr/Red

Analog Output.

In SD Only Mode: Chroma/Red/V Analog Output; in HD Only Mode and Simultaneous HD/SD Mode:

Pb/Blue [HD] Analog Output.

P_HSYNC

P_VSYNC

P_BLANK

S_BLANK

S_HSYNC

S_VSYNC

Y7 to Y0

I

Video Horizontal Sync Control Signal for HD in Simultaneous SD/HD Mode and HD Only Mode.

Video Vertical Sync Control Signal for HD in Simultaneous SD/HD Mode and HD Only Mode.

Video Blanking Control Signal for HD in Simultaneous SD/HD Mode and HD Only Mode.

Video Blanking Control Signal for SD Only.

I

I/O

I

Video Horizontal Sync Control Signal for SD Only.

Video Vertical Sync Control Signal for SD Only.

SD or Progressive Scan/HDTV Input Port for Y Data. Input port for interleaved progressive scan data. The

LSB is set up on Pin Y0.

C7 to C0

I

Progressive Scan/HDTV Input Port 4:4:4 Input Mode. This port is used for the Cb [Blue/U] data. The LSB is

set up on Pin C0.

S7 to S0

RESET

I

SD or Progressive Scan/HDTV Input Port for Cr [Red/V] data in 4:4:4 input mode. LSB is set up on Pin S0.

RESET

This input resets the on-chip timing generator and sets the ADV7322 into default register setting.

an active low signal.

is

R_SET1, R_SET2

I

A 3040 Ω resistor must be connected from this pin to AGND and is used to control the amplitudes of the

DAC outputs.

SCLK

SDA

ALSB

I

I²C Port Serial Interface Clock Input.

I²C Port Serial Data Input/Output.

I/O

I

TTL Address Input. This signal sets up the LSB of the I²C address. When this pin is tied low, the I²C filter is

activated, which reduces noise on the I²C interface.

V_{DD_IO}

V_DD

P

Power Supply for Digital Inputs and Outputs.

Digital Power Supply.

V_AA

P

Analog Power Supply.

V_REF

I/O

Optional External Voltage Reference Input for DACs or Voltage Reference Output (1.235 V).

External Loop Filter for the Internal PLL.

Multifunctional Input. Real time control (RTC) input, timing reset input, subcarrier reset input.

This input pin must be tied high (V_{DD_IO}) for the ADV7322 to interface over the I²C port.

Digital Input/Output Ground.

EXT_LF

RTC_SCR_TR

I²C

I

GND_IO

TEST0 to

TEST5

I

Not used. Tie to DGND

Rev. PrA | Page 19 of 88

ADV7322

Preliminary Technical Data

TYPICAL PERFORMANCE CHARACTERISTICS

Y PASS BAND IN PS OVERSAMPLING MODE

PROG SCAN Pr/Pb RESPONSE. LINEAR INTERP FROM 4:2:2 TO 4:4:4

0

1.0

0.5

–10

–20

–30

–40

–50

–60

–70

–80

0

–0.5

–1.0

–1.5

–2.0

–2.5

–3.0

0

20

40

60

80 100 120 140 160 180 200

FREQUENCY (MHz)

0

2

4

6

8

10

12

FREQUENCY (MHz)

Figure 20. PS—UV 8× Oversampling Filter (Linear)

Figure 23. PS—Y 8× Oversampling Filter (Pass Band)

PROG SCAN Pr/Pb RESPONSE. SSAF INTERP FROM 4:2:2 TO 4:4:4

Pr/Pb RESPONSE IN HDTV OVERSAMPLING MODE

0

–10

–20

–30

–40

–50

–60

–70

–80

–10

–20

–30

–40

–50

–60

–70

–80

0

20

40

60

80 100 120 140 160 180 200

FREQUENCY (MHz)

0

20

40

60

80

100

120

140

FREQUENCY (MHz)

Figure 24. HDTV—UV (2× Oversampling Filter)

Figure 21. PS—UV 8× Oversampling Filter (SSAF)

Y RESPONSE IN PS OVERSAMPLING MODE

Y RESPONSE IN HDTV OVERSAMPLING MODE

0

–10

–20

–30

–40

–50

–60

–70

–80

0

–10

–20

–30

–40

–50

–60

–70

–80

0

20

40

60

80 100 120 140 160 180 200

FREQUENCY (MHz)

0

20

40

60

80

100

120

140

FREQUENCY (MHz)

Figure 22. PS—Y (8× Oversampling Filter)

Figure 25. HDTV—Y (2× Oversampling Filter)

Rev. PrA | Page 20 of 88

Preliminary Technical Data

ADV7322

0

–10

–20

–30

–40

–50

–60

–70

0

–10

–20

–30

–40

–50

–60

–70

0

2

4

6

8

10

12

0

2

4

6

8

10

12

FREQUENCY (MHz)

Figure 26. Luma NTSC Low-Pass Filter

Figure 29. Luma PAL Notch Filter

Y RESPONSE IN SD OVERSAMPLING MODE

0

–10

–20

–30

–40

–50

–60

–70

0

–10

–20

–30

–40

–50

–60

–70

–80

2

4

6

8

20

40

60

80 100 120 140 160 180 200

FREQUENCY (MHz)

Figure 27. Luma PAL Low-Pass Filter

Figure 30. Y—16× Oversampling Filter

0

–10

–20

–30

–40

–50

–60

–70

0

–10

–20

–30

–40

–50

–60

–70

2

4

6

8

2

4

6

8

10

12

FREQUENCY (MHz)

Figure 28. Luma NTSC Notch Filter

Figure 31. Luma SSAF Filter up to 12 MHz

Rev. PrA | Page 21 of 88

ADV7322

Preliminary Technical Data

4

2

0

–10

–20

–30

–40

–50

–60

–70

0

–2

–4

–6

–8

–10

–12

0

2

3

4

5

6

7

0

2

4

6

8

10

12

1

FREQUENCY (MHz)

Figure 32. Luma SSAF Filter—Programmable Responses

Figure 35. Luma CIF Low-Pass Filter

5

0

–10

–20

–30

–40

–50

–60

–70

4

3

2

1

0

–1

2

4

6

8

5

6

7

0

1

2

3

4

FREQUENCY (MHz)

Figure 33. Luma SSAF Filter—Programmable Gain

Figure 36. Luma QCIF Low-Pass Filter

1

0

–10

–20

–30

–40

–50

–60

–70

–1

–2

–3

–4

–5

0

1

2

3

4

5

6

7

2

4

6

8

FREQUENCY (MHz)

Figure 34. Luma SSAF Filter—Programmable Attenuation

Figure 37. Chroma 3.0 MHz Low-Pass Filter

Rev. PrA | Page 22 of 88

Preliminary Technical Data

ADV7322

0

–10

–20

–30

–40

–50

–60

–70

0

–10

–20

–30

–40

–50

–60

–70

10

12

0

2

4

6

8

0

2

4

6

8

10

12

FREQUENCY (MHz)

Figure 38. Chroma 2.0 MHz Low-Pass Filter

Figure 41. Chroma 0.65 MHz Low-Pass Filter

0

–10

–20

–30

–40

–50

–60

–70

0

–10

–20

–30

–40

–50

–60

–70

2

4

6

8

10

2

4

6

8

10

FREQUENCY (MHz)

Figure 39. Chroma 1.3 MHz Low-Pass Filter

Figure 42. Chroma CIF Low-Pass Filter

0

–10

–20

–30

–40

–50

–60

–70

0

–10

–20

–30

–40

–50

–60

–70

2

4

6

8

10

2

4

6

8

FREQUENCY (MHz)

Figure 40. Chroma 1.0 MHz Low-Pass Filter

Figure 43. Chroma QCIF Low-Pass Filter

Rev. PrA | Page 23 of 88

ADV7322

Preliminary Technical Data

MPU PORT DESCRIPTION

The ADV7322 supports a 2-wire serial (I²C-compatible)

microprocessor bus driving multiple peripherals. This port

operates in an open-drain configuration. Two inputs, serial data

(SDA) and serial clock (SCL), carry information between any

device connected to the bus and the ADV7322. Each slave

device is recognized by a unique address. The ADV7322 has

four possible slave addresses for both read and write operations.

These are unique addresses for each device and are illustrated in

Figure 44. The LSB sets either a read or write operation. Logic 1

corresponds to a read operation, while Logic 0 corresponds to a

write operation. A1 is set by setting the ALSB pin of the

ADV7322 to Logic 0 or Logic 1. When ALSB is set to 1, there is

greater input bandwidth on the I²C lines, which allows high

speed data transfers on this bus. When ALSB is set to 0, there is

reduced input bandwidth on the I²C lines, which means that

pulses of less than 50 ns will not pass into the I²C internal

controller. This mode is recommended for noisy systems.

The ADV7322 acts as a standard slave device on the bus. The

data on the SDA pin is eight bits long, supporting the 7-bit

addresses plus the R/ bit. It interprets the first byte as the

W

device address and the second byte as the starting subaddress.

There is a subaddress auto-increment facility. This allows data

to be written to or read from registers in ascending subaddress

sequence starting at any valid subaddress. A data transfer is

always terminated by a stop condition. The user can also access

any unique subaddress register on a one-by-one basis without

having to update all the registers.

Stop and start conditions can be detected at any stage during

the data transfer. If these conditions are asserted out of

sequence with normal read and write operations, then they

cause an immediate jump to the idle condition. During a given

SCL high period, the user should only issue one start condition,

one stop condition, or a single stop condition followed by a

single start condition. If an invalid subaddress is issued by the

user, the ADV7322 will not issue an acknowledge and will

return to the idle condition. If in auto-increment mode the user

exceeds the highest subaddress, the following action is taken:

1

0

1

0

1

A1

X

ADDRESS

CONTROL

SET UP BY

ALSB

1. In read mode, the highest subaddress register contents are

output until the master device issues a no-acknowledge.

This indicates the end of a read. A no-acknowledge

condition is when the SDA line is not pulled low on the

ninth pulse.

READ/WRITE

CONTROL

0

1

WRITE

READ

Figure 44. ADV7322 Slave Address = 0xD4

2. In write mode, the data for the invalid byte is not loaded

into any subaddress register, a no-acknowledge is issued by

the ADV7322, and the part returns to the idle condition.

To control the various devices on the bus, the following protocol

must be followed. First the master initiates a data transfer by

establishing a start condition, defined by a high-to-low

transition on SDA while SCL remains high. This indicates that

an address/data stream will follow. All peripherals respond to

the start condition and shift the next eight bits (7-bit address +

Before writing to the subcarrier frequency registers, it is a

requirement that the ADV7322 is reset at least once after

power-up.

The four subcarrier frequency registers must be updated,

starting with subcarrier frequency register 0 through subcarrier

frequency register 3. The subcarrier frequency will not update

until the last subcarrier frequency register byte has been

received by the ADV7322.

R/ bit). The bits are transferred from MSB down to LSB. The

W

peripheral that recognizes the transmitted address responds by

pulling the data line low during the ninth clock pulse. This is

known as an acknowledge bit. All other devices withdraw from

the bus at this point and maintain an idle condition. The idle

condition is where the device monitors the SDA and SCL lines

waiting for the start condition and the correct transmitted

Figure 45 illustrates an example of data transfer for a write

sequence and the start and stop conditions. Figure 46 shows bus

write and read sequences.

address. The R/ bit determines the direction of the data.

W

Logic 0 on the LSB of the first byte means that the master will

write information to the peripheral. Logic 1 on the LSB of the

first byte means that the master will read information from the

peripheral.

Rev. PrA | Page 24 of 88

Preliminary Technical Data

ADV7322

SDATA

SCLOCK

S

P

9

1–7

9

1–7

8

1–7

8

START ADRR R/W ACK SUBADDRESS ACK

DATA

ACK

STOP

Figure 45. Bus Data Transfer

WRITE

S

SLAVE ADDR A(S)

LSB = 0

SUBADDR

A(S)

DATA

A(S)

DATA

A(M)

A(S) P

SEQUENCE

LSB = 1

READ

SEQUENCE

SLAVE ADDR A(S)

S

SLAVE ADDR A(S)

DATA

A(M) P

S = START BIT

P = STOP BIT

A(S) = ACKNOWLEDGE BY SLAVE

A(M) = ACKNOWLEDGE BY MASTER

A (S) = NO-ACKNOWLEDGE BY SLAVE

A (M) = NO-ACKNOWLEDGE BY MASTER

Figure 46. Read and Write Sequence

Rev. PrA | Page 25 of 88

ADV7322

Preliminary Technical Data

REGISTER ACCESS

The MPU can write to or read from all of the registers of the

ADV7322 except the subaddress registers, which are write only

registers. The subaddress register determines which register the

next read or write operation will access. All communications

with the part through the bus start with an access to the

subaddress register. A read/write operation is then performed

from/to the target address, which increments to the next

address until a stop command is performed on the bus.

REGISTER PROGRAMMING

The following tables describe the functionality of each register.

All registers can be read from as well as written to, unless

otherwise stated.

SUBADDRESS REGISTER (SR7 TO SR0)

The communication register is an 8-bit write-only register. After

the part is accessed over the bus and a read/write operation is

selected, the subaddress is set up. The subaddress register

determines to/from which register the operation takes place.

Table 7. Registers 0x00 to 0x01

Reg. Reset

Values

SR7–

SR0

0x00

Register

Power

Mode

Bit Description

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

0

1

Register Setting

Sleep mode off.

Sleep mode on.

(Shaded)

0xFC

Sleep Mode. With this

control enabled, the

current consumption is

reduced to µA level. All

DACs and the internal PLL

cct are disabled. I²C

registers can be read from

and written to in sleep

mode.

Register

PLL and Oversampling

Control. This control

allows the internal PLL cct

to be powered down and

the oversampling to be

switched off.

0

1

PLL on.

PLL off.

DAC F: Power On/Off.

0

1

DAC F off.

DAC F on.

DAC E off.

DAC E on.

DAC D off.

DAC D on.

DAC D off.

DAC C on.

DAC B off.

DAC B on.

DAC A off.

DAC A on.

Reserved

DAC E: Power On/Off.

DAC D: Power On/Off.

DAC C: Power On/Off.

DAC B: Power On/Off.

DAC A: Power On/Off.

0

1

0

1

0

1

0

1

0

1

0x01

Mode

Select

Reserved

0

Clock Edge.

0

1

Cb clocked on rising

edge.

Y clocked on rising edge

Only for PS

interleaved

input at 27 MHz.

Register

Reserved.

0

Clock Align.

0

1

Must be set if the phase

delay between the two

input clocks is

Only if two

input clocks are

used.

<9.25 ns or >27.75 ns.

Input Mode.

0

1

0

1

0

1

0

1

0

1

SD input only.

PS input only.

0x38

HDTV input only.

SD and PS [16-bit].

SD and PS [8-bit].

SD and HDTV [SD

oversampled].

1

0

1

SD and HDTV [HDTV

oversampled].

PS only [at 54 MHz].

Y/C/S Bus Swap.

0

1

Allows data to be

See Table 21.

applied to data ports in

various configurations

(SD feature only).

Rev. PrA | Page 26 of 88

Preliminary Technical Data

ADV7322

Table 8. Registers 0x02 to 0x0F

SR7–

SR0

0x02

Register

Mode Register 0

Bit Description

Reserved

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

0

Bit 0

0

Register Setting

Zero must be written to

these bits.

Reset Values

0x20

Test Pattern Black

Bar

0

1

Disabled.

Enabled.

0x11, Bit 2 must

also be enabled.

Manual RGB

Matrix Adjust

0

1

Disable manual RGB matrix

adjust.

Enable manual RGB matrix

adjust.

Sync on RGB¹

0

1

No sync.

Sync on all RGB outputs.

RGB component outputs.

YPrPb component outputs.

No Sync output.

Output SD syncs on

RGB/YPrPb

Output

SD Sync

0

1

0

1

,

S_HSYNC S_VSYNC

pins.

S_BLANK

No sync output.

Output HD,ED, syncs on

HD Sync

0

1

,

.

S_HSYNC S_VSYNC

0x03

0x04

RGB Matrix 0

RGB Matrix 1

x

LSB for GY.

LSB for RV.

0x03

0xF0

x

LSB for BU.

x

LSB for GV.

x

0

x

0

LSB for GU.

Bits 9–2 for GY.

Bits 9–2 for GU.

Bits 9–2 for GV.

Bits 9–2 for BU.

Bits 9–2 for RV.

0%

0x05

0x06

0x07

0x08

0x09

0x0A

RGB Matrix 2

RGB Matrix 3

RGB Matrix 4

RGB Matrix 5

RGB Matrix 6

DAC A, B, C Output

Level²

x

0

x

0

x

0

x

0

x

0

x

0

0x4E

0x0E

0x24

0x92

0x7C

0x00

Positive Gain to

DAC Output

Voltage

0

1

0

…

1

0

+0.018%

0.036%

…

+7.382%

+7.5%

−7.5%

0

1

0

1

0

1

0

1

0

1

0

1

0

Negative Gain to

DAC Output

Voltage

0

1

0

1

0

…

1

0

−7.382%

−7.364%

…

−0.018%

0%

1

0

1

0

1

0

1

0

1

0

1

0

1

0

0x0B

DAC D, E, F Output

Level

Positive Gain to

DAC Output

Voltage

0x00

0

1

0

…

1

0

+0.018%

0.036%

…

+7.382%

+7.5%

−7.5%

0

1

0

1

0

1

0

1

0

1

0

1

0

Negative Gain to

DAC Output

Voltage

0

1

0

1

0

…

1

−7.382%

−7.364%

…

1

−0.018%

0x0C

0x0D

0x0E

0x0F

Reserved

0x00

¹For more detail, refer to Appendix 7.

²For more detail on the programmable output levels, refer to the Programmable DAC Gain Control section.

Rev. PrA | Page 27 of 88

ADV7322

Preliminary Technical Data

Table 9. Registers 0x10 to 0x11

SR7–

Reset

SR0

Register

Bit Description

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Register Setting

EIA770.2 output

EIA770.1 output

Note

Values

0x10

HD Mode

Register 1

HD Output

Standard

0

1

0

1

0

0x00

Output levels for

full input range

1

Reserved

Input Sync

Format

0

1

,

HSYNC VSYNC

BLANK

EAV/SAV codes

HD/ED Input

Mode

0

SMPTE 293M, ITU-

BT 1358

525p @

59.94 Hz

0

1

0

Async mode

BTA-1004, ITU-

BT 1362

525p @

59.94 Hz

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

ITU-BT 1358

625p @

50 Hz

ITU-BT 1362

625p @

50 Hz

SMPTE 296M-1, 2

SMPTE 296M-3

SMPTE 296M-4, 5

SMPTE 296M-6

SMPTE 296M-7, 8

SMPTE 240M

720p @

60/59.94 Hz

720p @

50 Hz

720p @

30/29.97 Hz

720p @

25 Hz

720p @

24/23.98 Hz

1035i @

60/59.94 Hz

0

1

0

1

0

1

0

1

Reserved

SMPTE 274M-4,5

1080i @

30/29.97 Hz

0

1

0

1

0

1

0

1

0

1

SMPTE 274M-6

SMPTE 274M-7, 8

SMPTE 274M-9

1080i @

25 Hz

1080p @

30/29.97 Hz

1080p @

25 Hz

SMPTE 274M-

10, 11

1080p @

24/23.98 Hz

10010–11111

Reserved

0x11

HD Mode

Register 2

HD Pixel Data

Valid

0

1

Pixel data valid off

Pixel data valid on

Reserved

0x00

0

HD Test Pattern

Enable

0

1

HD test pattern off

HD test pattern on

Hatch

HD Test Pattern

Hatch/Field

0

1

Field/frame

Disabled

HD VBI Open

0

1

Enabled

HD Undershoot

Limiter

0

1

0

1

0

1

Disabled

Only

available in

EDTV

−11 IRE

−6 IRE

(525p/625p)

−1.5 IRE

HD Sharpness

Filter

0

1

Disabled

Enabled

Rev. PrA | Page 28 of 88

Preliminary Technical Data

ADV7322

Table 10. Register 0x12

SR7–

Reset

SR0

Register

Bit Description

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Register Setting

0 clk cycles

1 clk cycles

2 clk cycles

3 clk cycles

4 clk cycles

0 clk cycles

1 clk cycle

2 clk cycles

3 clk cycles

4 clk cycles

Disabled

Values

0x12

HD Mode HD Y Delay with Respect

Register

3

0

1

0

1

0

1

0

1

0

0x00

to Falling Edge of

HSYNC

HD Color Delay with

Respect to Falling Edge of

HSYNC

0

1

0

1

0

1

0

1

0

HD CGMS

0

1

Enabled

HD CGMS CRC

0

1

Disabled

Enabled

Table 11. Registers 0x13 to 0x14

SR7–

Reset

SR0

Register

Bit Description

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Register Setting

Values

0x13

HD Mode

Register 4

HD Cr/Cb Sequence

0

Cb after falling edge of

.

0x4C

HSYNC

1

Cr after falling edge of

.

HSYNC

Reserved

0

0 must be written to this bit.

Reserved

0

0 must be written here

Disabled.

Sinc Filter on DAC D, E, F

0

1

Enabled.

Reserved

0

0 must be written to this bit.

Disabled.

HD Chroma SSAF

0

1

Enabled.

HD Chroma Input

HD Double Buffering

HD Timing Reset

0

1

4:4:4

4:2:2

0

1

Disabled.

Enabled.

0x14

HD Mode

Register 5

x

A low-high-low transition

resets the internal HD timing

counters.

0x00

HD Hsync Generation¹

0

1

Signal duration on S_Hsync

same as ADV731x.

Signal duration on S_Hsync =

sync duration on embedded Y.

HD Vsync Generation¹

HD Blank Polarity

0

1

Field signal out on S_Vsync pin.

Vsync Signal. Duration = Vsync

on embedded Y.

0

1

active high.

active low.

BLANK

HD Macrovision for 525p

and 625p

0

1

Macrovision disabled.

Macrovision enabled.

Reserved

0

0 must be written to these bits.

HD

/Field Input

VSYNC

0

1

0 = field input.

1 =

input.

VSYNC

Horizontal/Vertical

counters²

0

1

Update Horizontal/Vertical

counters.

Horizontal/Vertical counters

free running.

¹Used in conjunction with HD_SYNC in Register 0x02, Bit 7 set to 1.

²When set to 0, the Horizontal/Vertical counters automatically wrap around at the end of the Line/field/frame of the standard selected. When set to 1, the

Horizontal/Vertical counters are free running and wrap around when external sync signals indicate so.

Rev. PrA | Page 29 of 88

ADV7322

Preliminary Technical Data

Table 12. Register 0x15

SR7–

Reset

SR0

Register

Bit Description

Reserved

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Register Setting

0 must be written to this bit

Disabled

Values

0x15

HD Mode

Register 6

0

0x00

HD RGB Input

0

1

Enabled

HD Sync on PrPb

0

1

Disabled

Enabled

HD Color DAC Swap

0

1

DAC E = Pb; DAC F = Pr

DAC E = Pr; DAC F = Pb

Gamma Curve A

Gamma Curve B

Disabled

HD Gamma Curve A/B

HD Gamma Curve Enable

HD Adaptive Filter Mode

HD Adaptive Filter Enable

0

1

0

1

Enabled

0

1

Mode A

Mode B

0

1

Disabled

Enabled

Rev. PrA | Page 30 of 88

Preliminary Technical Data

ADV7322

Table 13. Registers 0x16 to 0x37

SR7–

Register

Setting

Reset

Values

SR0

Register

Bit Description

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

0x16

0x17

HD Y Level¹

HD Cr Level¹

HD Cb Level¹

x

Y level value

Cr level value

0xA0

0x80

0x18

x

Cb level value

0x80

0x19

0x1A

0x1B

0x1C

0x1D

0x1E

0x1F

0x20

Reserved

0x00

Reserved

HD Sharpness

Filter Gain

HD Sharpness Filter Gain Value A

0

Gain A = 0

0

1

Gain A = +1

…

0

…

1

…

1

…

1

…

Gain A = +7

1

0

Gain A = −8

…

1

…

1

…

1

…

1

…

Gain A = −1

HD Sharpness Filter Gain Value B

0

Gain B = 0

0

1

Gain B = +1

…

0

…

1

…

1

…

1

…

Gain B = +7

1

0

Gain B = −8

…

1

…

1

…

1

…

1

…

Gain B = −1

0x21

0x22

0x23

0x24

0x25

0x26

0x27

0x28

0x29

0x2A

0x2B

0x2C

0x2D

0x2E

0x2F

0x30

0x31

0x32

0x33

0x34

0x35

0x36

0x37

HD CGMS Data 0

HD CGMS Data 1

HD CGMS Data 2

HD Gamma A

HD Gamma B

HD CGMS Data Bits

0

C19

C11

C3

x

C18

C10

C2

x

C17

C9

C1

x

C16

C8

C0

x

CGMS 19–16

0x00

HD CGMS Data Bits

C15

C7

x

C14

C6

x

C13

C5

x

C12

C4

x

CGMS 15–8

HD CGMS Data Bits

CGMS 7–0

A0

HD Gamma Curve A Data Points

HD Gamma Curve B Data Points

x

A1

x

A2

x

A3

x

A4

x

A5

x

A6

x

A7

x

A8

x

A9

x

B0

x

B1

x

B2

x

B3

x

B4

x

B5

x

B6

x

B7

x

B8

x

B9

¹For use with internal test pattern only.

Rev. PrA | Page 31 of 88

ADV7322

Preliminary Technical Data

Table 14. Registers 0x38 to 0x3D

SR7–

Register

Setting

Reset

Values

SR0

Register

Bit Description

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

0

Bit 2

0

Bit 1

0

Bit 0

0

0x38

HD Adaptive Filter

Gain 1

HD Adaptive

Filter Gain 1

Value A

Gain A = 0

Gain A = +1

…

0x00

0

1

…

0

…

1

…

1

…

1

Gain A = +7

Gain A = −8

…

1

0

…

1

…

1

…

1

…

1

Gain A = −1

Gain B = 0

Gain B = +1

…

HD Adaptive

Filter Gain 1

Value B

0

1

…

0

…

1

…

1

…

1

Gain B = +7

Gain B = −8

…

1

0

…

1

…

1

…

1

…

1

Gain B = −1

Gain A = 0

Gain A = +1

…

0x39

HD Adaptive Filter

Gain 2

HD Adaptive

Filter Gain 2

Value A

0

1

…

0

…

1

…

1

…

1

Gain A = +7

Gain A = −8

…

1

0

…

1

…

1

…

1

…

1

Gain A = −1

Gain B = 0

Gain B = +1

…

HD Adaptive

Filter Gain 2

Value B

0

1

…

0

…

1

…

1

…

1

Gain B = +7

Gain B = −8

…

1

0

…

1

…

1

…

1

…

1

Gain B = −1

Gain A = 0

Gain A = +1

…

0x3A

HD Adaptive Filter

Gain 3

HD Adaptive

Filter Gain 3

Value A

0

1

…

0

…

1

…

1

…

1

Gain A = +7

Gain A = −8

…

1

0

…

1

…

1

…

1

…

1

Gain A = −1

Gain B = 0

Gain B = +1

…

HD Adaptive

Filter Gain 3

Value B

0

1

…

0

…

1

…

1

…

1

Gain B = +7

Gain B = −8

…

1

0

…

1

…

1

…

1

…

1

Gain B = −1

Threshold A

0x3B

0x3C

0x3D

HD Adaptive Filter

Threshold A

HD Adaptive

Filter Threshold

A Value

x

0x00

HD Adaptive Filter

Threshold B

HD Adaptive

Filter Threshold

B Value

x

Threshold B

Threshold C

HD Adaptive Filter

Threshold C

HD Adaptive

Filter Threshold

C Value

Rev. PrA | Page 32 of 88

Preliminary Technical Data

ADV7322

Table 15. Registers 0x3E to 0x43

SR7–

Reset

Values

0x00

SR0

Register

Bit Description

Reserved

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Register Setting

0x3E

0x3F

0x40

Reserved

SD Mode Register 0

SD Standard

0

1

0

1

0

1

NTSC

PAL B, D, G, H, I

PAL M

PAL N

SD Luma Filter

0

1

0

1

0

1

0

1

0

1

0

1

0

1

LPF NTSC

LPF PAL

Notch NTSC

Notch PAL

SSAF luma

Luma CIF

Luma QCIF

Reserved

1.3 MHz

0.65 MHz

1.0 MHz

2.0 MHz

SD Chroma Filter

0

1

0

1

0

1

0

1

0

1

0

1

0

1

Reserved

Chroma CIF

Chroma QCIF

3.0 MHz

0x41

0x42

Reserved

SD PrPb SSAF

0x00

0x08

SD Mode Register 1

0

1

Disabled

Enabled

SD DAC Output 1

SD DAC Output 2

SD Pedestal

0

1

Refer to output

configuration section

Refer to output

configuration section

Disabled

0

1

0

1

Enabled

SD Square Pixel

SD VCR FF/RW Sync

SD Pixel Data Valid

0

1

Disabled

Enabled

Disabled

Enabled

Disabled

Enabled

0

1

0

1

SD SAV/EAV Step

Edge Control

0

1

Disabled

Enabled

0x43

SD Mode Register 2

SD Pedestal YPrPb

Output

SD Output Levels Y

0

1

No pedestal on YUV

7.5 IRE pedestal on YUV

Y = 700 mV/300 mV

Y = 714 mV/286 mV

700 mV p-p[PAL];

1000 mV p-p[NTSC]

700 mV p-p

0x00

0

1

SD Output Levels PrPb

0

1

0

1

1000 mV p-p

648 mV p-p

SD VBI Open

0

1

Disabled

Enabled

SD CC Field Control

0

1

0

1

0

1

CC disabled

CC on odd field only

CC on even field only

CC on both fields

Reserved

0

Rev. PrA | Page 33 of 88

ADV7322

Preliminary Technical Data

Table 16. Registers 0x44 to 0x49

SR7–

Reset

SR0

0x44

Register

SD Mode

Register 3

Bit Description

SD VSYNC-3H

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

0

1

Register Setting

Disabled

Values

0x00

= 2.5 lines [PAL],

VSYNC

= 3 lines [NTSC]

VSYNC

SD RTC/TR/SCR

0

1

0

1

0

1

Genlock disabled

Subcarrier Reset

Timing Reset

RTC enabled

SD Active Video Length

SD Chroma

0

1

720 pixels

710 [NTSC]/702[PAL]

Chroma enabled

Chroma disabled

Enabled

0

1

SD Burst

0

1

Disabled

SD Color Bars

SD DAC Swap

0

1

Disabled

Enabled

DAC A = luma, DAC B = chroma

DAC A = chroma, DAC B = luma

0

1

0x45

0x46

Reserved

SD Mode

Register 4

0x00

0x01

NTSC Color Subcarrier

Adjust (Falling Edge of

HS to Start of Color

Burst)¹

0

1

0

1

0

5.17 µs

5.31 µs (default)

5.59 µs (must be set for

Macrovision compliance)

Reserved

Disabled

Enabled

Disabled

Enabled

Disabled

Enabled

Disabled

Enabled

Disabled

Enabled

0 must be written to this bit

1

0

1

0x47

0x48

0x49

SD Mode

Register 5

SD PrPb Scale

SD Y Scale

0x00

0

1

SD Hue Adjust

SD Brightness

SD Luma SSAF Gain

0

1

0

1

0

1

Reserved

SD Double Buffering

0

SD Mode

Register 6

0

0 must be written to this bit

Disabled

Enabled

8-bit input

16-bit input

0 must be written to this bit

Disabled

Enabled

Disabled

Enabled

Gamma Curve A

Gamma Curve B

Disabled

−11 IRE

−6 IRE

0

1

SD Input Format

0

1

Reserved

SD Digital Noise

Reduction

0

1

SD Gamma Control

0

1

SD Gamma Curve

0

1

SD Mode

Register 7

SD Undershoot Limiter

0

1

0

1

0

1

−1.5 IRE

Reserved

SD Black Burst Output on

DAC Luma

0

0 must be written to this bit

Disabled

Enabled

0

1

SD Chroma Delay

0

1

0

1

0

1

Disabled

4 clk cycles

8 clk cycles

Reserved

0

0 must be written to this bit

0

¹NTSC color bar adjust should be set to 10 b for macrovision compliance.

Rev. PrA | Page 34 of 88

Preliminary Technical Data

ADV7322

Table 17. Registers 0x4A to 0x58

SR7–

Reset

Value

0x08

SR0

0x4A

Register

SD Timing

Register 0

Bit Description

SD Slave/Master

Mode

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

0

1

Register Setting

Slave mode.

Master mode.

Mode 0.

Mode 1.

Mode 2.

SD Timing Mode

0

1

0

1

0

1

Mode 3.

SD BLANK Input

SD Luma Delay

0

1

Enabled.

Disabled.

0

1

0

1

0

1

No delay.

2 clk cycles.

4 clk cycles.

6 clk cycles.

−40 IRE.

SD Min. Luma

Value

SD Timing Reset

0

1

0

−7.5 IRE.

x

0

A low-high-low transition will

reset the internal SD timing

counters.

0x4B

SD Timing

Register 1

SD

Width

0

1

0

1

0

1

T_a= 1 clk cycle.

T_a= 4 clk cycles.

T_a= 16 clk cycles.

T_a= 128 clk cycles.

T_b= 0 clk cycle.

0x00

HSYNC

to

Delay

0

1

0

1

0

1

HSYNC

T_b= 4 clk cycles.

T_b= 8 clk cycles.

VSYNC

T_b= 18 clk cycles.

SD

to

HSYNC VSYNC

x

0

1

T_c= T_b.

T_c= T_b+ 32 µs.

Rising Edge Delay

[Mode 1 Only]

Width

0

1

0

1

0

1

1 clk cycle.

4 clk cycles.

16 clk cycles.

128 clk cycles.

0 clk cycles.

1 clk cycle.

2 clk cycles.

3 clk cycles.

Subcarrier Frequency Bits 7–0.

VSYNC

[Mode 2 Only]

to Pixel

Data Adjust

0

1

x

0

1

0

1

x

HSYNC

0x4C

x

0x1E¹

SD F_SCRegister 0¹

SD F_SCRegister 1

SD F_SCRegister 2

SD F_SCRegister 3

SD F_SCPhase

SD Closed

0x4D

0x4E

0x4F

0x50

0x51

x

Subcarrier Frequency Bits 15–8.

Subcarrier Frequency Bits 23–16.

Subcarrier Frequency Bits 31–24.

Subcarrier Phase Bits 9–2.

0x7C

0xF0

0x21

0x00

Extended Data on

Even Fields

Extended Data Bits 7–0.

Captioning

0x52

0x53

0x54

0x55

SD Closed

Captioning

SD Closed

Captioning

SD Closed

Captioning

SD Pedestal

Register 0

Extended Data on

Even Fields

Data on Odd Fields

x

Extended Data Bits 15–8.

Data Bits 7–0.

0x00

x

Data on Odd Fields

x

Data Bits 15–8.

Pedestal on Odd

Fields

17

16

15

14

13

12

11

10

Setting any of these bits to 1 will

disable pedestal on the line num-

ber indicated by the bit settings.

0x56

0x57

0x58

SD Pedestal

Register 1

SD Pedestal

Register 2

SD Pedestal

Register 3

Pedestal on Odd

Fields

Pedestal on Even

Fields

Pedestal on Even

Fields

25

17

25

24

16

24

23

15

23

22

14

22

21

13

21

20

12

20

19

11

19

18

10

18

0x00

¹For precise NTSC FSC, this value should be programmed to 0x1F.

LINE 1

LINE 313

LINE 314

HSYNC

t_A

t_C

t_B

VSYNC

Figure 47. Timing Register 1 in PAL Mode

Rev. PrA | Page 35 of 88

ADV7322

Preliminary Technical Data

Table 18. Registers 0x59 to 0x64

SR7–

Reset

SR0

0x59

Register

SD CGMS/WSS 0

Bit Description

SD CGMS Data

SD CGMS CRC

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

19

Bit 2

18

Bit 1

17

Bit 0

16

Register Setting

CGMS Data Bits C19–C16

Disabled

Values

0x00

0

1

Enabled

SD CGMS on Odd

Fields

0

1

Disabled

Enabled

SD CGMS on Even

Fields

0

1

Disabled

Enabled

SD WSS

0

1

Disabled

Enabled

0x5A

SD CGMS/WSS 1

SD CGMS/WSS Data

13

5

12

4

11

3

10

2

9

8

CGMS Data Bits C13–C8, or

WSS Data Bits C13–C8

CGMS Data Bits C15–C14

CGMS/WSS Data Bits C7–C0

SD Y Scale Bits 1–0

0x00

15

7

14

6

0x00

0x5B

0x5C

SD CGMS/WSS 2

SD LSB Register

SD CGMS/WSS Data

SD LSB for Y Scale

Value

1

x

0

x

SD LSB for Cb Scale

Value

SD LSB for Cr Scale

Value

x

SD Cb Scale Bits 1–0

SD Cr Scale Bits 1–0

x

SD LSB for F_SCPhase

SD Y Scale Value

x

Subcarrier Phase Bits 1–0

SD Y Scale Bits 7–2

0x5D

0x5E

0x5F

SD Y Scale

Register

SD Cb Scale

Register

SD Cr Scale

Register

SD Hue Register

SD Brightness/

WSS

x

0x00

SD Cb Scale Value

SD Cr Scale Value

x

SD Cb Scale Bits 7–2

SD Cr Scale Bits 7–2

0x60

0x61

SD Hue Adjust Value

SD Brightness Value

SD Blank WSS Data

x

SD Hue Adjust Bits 7–0

SD Brightness Bits 6–0

Disabled

Enabled

−4 dB

0 dB

0x00

Line 23

0

1

0

0x62

0x63

SD Luma SSAF

SD DNR 0

SD Luma SSAF

Gain/Attenuation

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

0x00

+4 dB

No gain

Coring Gain Border

Coring Gain Data

DNR Threshold

0x00

+1/16 [–1/8]

+2/16 [–2/8]

+3/16 [–3/8]

+4/16 [–4/8]

+5/16 [–5/8]

+6/16 [–6/8]

+7/16 [–7/8]

+8/16 [–1]

No gain

+1/16 [–1/8]

+2/16 [–2/8]

+3/16 [–3/8]

+4/16 [–4/8]

+5/16 [–5/8]

+6/16 [–6/8]

+7/16 [–7/8]

+8/16 [–1]

0

In DNR

mode,

the

values in

brackets

apply.

0

1

0

1

0

1

0

1

0

…

1

0

1

0

1

0

1

0

1

0

…

1

0x64

SD DNR 1

0

…

1

0

…

1

0

…

1

0

1

…

0

1

0x00

1

…

62

63

Border Area

0

1

2 pixels

4 pixels

Block Size Control

0

1

8 pixels

16 pixels

Rev. PrA | Page 36 of 88

Preliminary Technical Data

ADV7322

Table 19. Registers 0x65 to 0x7C

SR7–

Reset

SR0

Register

Bit Description

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Register Setting

Filter A

Values

0x65

SD DNR 2

DNR Input Select

0

1

0

1

0

1

0

1

0

0x00

Filter B

Filter C

Filter D

DNR Mode

0

1

0

1

…

0

1

x

DNR mode

DNR sharpness mode

DNR Block Offset

0

…

1

x

0

…

1

x

0

…

1

x

0 pixel offset

1 pixel offset

…

14 pixel offset

15 pixel offset

0x66

0x67

0x68

0x69

0x6A

0x6B

0x6C

0x6D

0x6E

0x6F

0x70

0x71

0x72

0x73

0x74

0x75

0x76

0x77

0x78

0x79

0x7A

SD Gamma A

SD Gamma B

SD Gamma Curve A Data Points

SD Gamma Curve B Data Points

SD Brightness Value

x

A0

A1

A2

A3

A4

A5

A6

A7

A8

A9

B0

0x00

B1

B2

B3

B4

B5

B6

B7

B8

B9

SD Brightness

Detect

Read only

0x7B

Field Count

Register

Field Count

Reserved

x

Read only

Reserved

Read only

Reserved

0x8x

0

Reserved

0

Reserved

0

Revision Code

Reserved

1

0

0x7C

0x00

Rev. PrA | Page 37 of 88

ADV7322

Preliminary Technical Data

Table 20. Registers 0x7D to 0x91

SR7-

SR0

Bit

Register

Reset

Values

Register

Description

Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Setting

0x7D Reserved

0x7E

0x7F

0x80

0x81

0x82

0x83

0x84

0x85

0x86

0x87

0x88

0x89

Reserved

Macrovision

MV Control Bits

MV Control Bit

x

0

x

0

x

0

x

0

x

0

x

0

x

0

x

0x00

0x8A Macrovision

0x8B

0x8C

Macrovision

0x8D Macrovision

0x8E

0x8F

0x90

0x91

Macrovision

0 must be written

to these bits

Rev. PrA | Page 38 of 88

Preliminary Technical Data

INPUT CONFIGURATION

ADV7322

input on Pins Y7 to Y0 and the CrCb data is input on Pins C7 to

C0. In 4:4:4 input mode, Y data is input on Pins Y7 to Y0,

Cb data is input on Pins C7 to C0, and Cr data is input on Pins

S7 to S0. If the YCrCb data does not conform to SMPTE 293M

(525p), ITU-R BT.1358M (625p), SMPTE 274M[1080i], SMPTE

296M[720p], SMPTE 240M(1035i) or BTA-T1004/1362, the

async timing mode must be used. RGB data can only be input in

4:4:4 format in PS input mode or in HDTV input mode when

HD RGB input is enabled. G data is input on Pins Y7 to Y0, R

data is input on Pins S7 to S0, and B data is input on Pins C7 to

C0. The clock signal must be input on Pin CLKIN_A.

Note that the ADV7322 defaults to simultaneous standard

definition and progressive scan upon power-up (Address[0x01]:

Input Mode = 011).

STANDARD DEFINITION ONLY

Address[0x01]: Input Mode = 000

The 8-bit multiplexed input data is input on Pins S7 to S0 (or

Pins Y7 to Y0, depending on Register Address 0x01, Bit 7), with

S0 being the LSB in 8-bit input mode (see Table 21). Input

standards supported are ITU-R BT.601/656. In 16-bit input

mode, the Y pixel data is input on Pins S7 to S0 and CrCb data

is input on Pins Y7 to Y0 (see Table 21).

MPEG2

ADV7322

DECODER

16-Bit Mode Operation

27MHz

When Register 0x01 Bit 7 = 0, CrCb data is input on the Y bus

and Y data is input on the S bus. When Register 0x01 Bit 7 = 1,

CrCb data is input on the C bus and Y data is input on Y bus.

YCrCb

CLKIN_A

8

Cb

Cr

Y

C[7:0]

S[7:0]

Y[7:0]

The 27 MHz clock input must be input on Pin CLKIN_A. Input

INTERLACED TO

PROGRESSIVE

S_VSYNC S_HSYNC

sync signals are input on the

S_BLANK

,

, and

P_VSYNC,

P_HSYNC,

P_BLANK

3

pins.

Table 21. SD 8-Bit and 16-Bit Configuration

Configuration

Figure 49. Progressive Scan Input Mode

Parameter

8-Bit Mode

16-Bit Mode

SIMULTANEOUS STANDARD DEFINITION AND

PROGRESSIVE SCAN OR HDTV

Register 0x01, Bit 7 = 0

Y Bus

S Bus

C Bus

CrCb

Y

656/601, YCrCb

Address[0x01]: Input Mode 011 (SD 8-Bit, PS 16-Bit) or 101

(SD and HD, SD Oversampled), 110 (SD and HD, HD

Oversampled), Respectively

Register 0x01, Bit 7 = 1

Y Bus

S Bus

C Bus

Y

YCrCb, PS, HDTV, or any other HD data must be input in 4:2:2

format. In 4:2:2 input mode, the HD Y data is input on Pins Y7

to Y0 and the HD CrCb data is input on Pins C7 to C0. If PS

4:2:2 data is interleaved onto a single 10-bit bus, Pins Y7 to Y0

are used for the input port. The input data is to be input at 27

MHz, with the data being clocked on the rising and falling edge

of the input clock. The input mode register at Address 0x01 is

set accordingly. If the YCrCb data does not conform to SMPTE

293M (525p), ITU-R BT.1358M (625p), SMPTE 274M[1080i],

SMPTE 296M[720p], SMPTE 240M(1035i) or BTA-T1004, the

async timing mode must be used.

CrCb

ADV7322

S_VSYNC,

S_HSYNC,

S_BLANK

3

MPEG2

DECODER

27MHz

8

CLKIN_A

The 8- bit standard definition data must be compliant with

ITU-R BT.601/656 in 4:2:2 format. Standard definition data is

input on Pins S7 to S0, with S0 being the LSB. The clock input

for SD must be input on CLKIN_A and the clock input for

HD/PS must be input on CLKIN_B. Synchronization signals

YCrCb

S[7:0] OR Y[7:0]*

*SELECTED BY ADDRESS 0x01 BIT 7

Figure 48. SD Only Input Mode

S_VSYNC S_HSYNC

are optional. SD syncs are input on Pins

S_BLANK P_VSYNC P_HSYNC

, and

,

PROGRESSIVE SCAN ONLY OR HDTV ONLY

and

P_BLANK

. HD syncs on Pins

,

Address[0x01]: Input Mode = 001 or 010, Respectively

.

YCrCb progressive scan, HDTV, or any other HD YCrCb data

can be input in 4:2:2 or 4:4:4. In 4:2:2 input mode, the Y data is

Rev. PrA | Page 39 of 88

ADV7322

Preliminary Technical Data

ADV7322

PROGRESSIVE SCAN AT 27 MHZ (DUAL EDGE)

OR 54 MHZ

S_VSYNC,

S_HSYNC,

S_BLANK

3

Address[0x01]: Input Mode 100 or 111, Respectively

MPEG2

DECODER

27MHz

YCrCb progressive scan data can be input at 27 MHz or

54 MHz. The input data is interleaved onto a single 8-bit bus

and is input on Pins Y7 to Y0. When a 27 MHz clock is supplied,

the data is clocked in on the rising and falling edge of the input

clock and CLOCK EDGE [Address 0x01, Bit 1] must be set

accordingly.

CLKIN_A

S[7:0]

YCrCb

8

CrCb

Y

8

C[7:0]

Y[7:0]

INTERLACED TO

PROGRESSIVE

Table 22 provides an overview of all possible input configurations.

Figure 53, Figure 54, and Figure 55 show the possible conditions:

(a) Cb data on the rising edge; and (b) Y data on the rising edge.

P_VSYNC,

P_HSYNC,

P_BLANK

3

27MHz

CLKIN_B

Figure 50. Simultaneous PS and SD Input

Y7–Y0

FF

00

XY

Cb0

Y0

Cr0

Y1

ADV7322

CLOCK EDGE ADDRESS 0x00 BIT 1 SHOULD BE SET TO 0 IN THIS CASE.

S_VSYNC,

S_HSYNC,

3

Figure 53. Input Sequence in PS Bit Interleaved Mode (EAV/SAV)

S_BLANK

SDTV

DECODER

27MHz

CLKIN_A

CLKIN_B

YCrCb 8

S[7:0]

Y7–Y0

FF

00

XY

Y0

Cb0

Y1

Cr0

HDTV

DECODER

CrCb 8

C[7:0]

Y[7:0]

1080i

OR

CLOCK EDGE ADDRESS 0x00 BIT 1 SHOULD BE SET TO 1 IN THIS CASE.

Y

8

720p

OR

P_VSYNC,

P_HSYNC,

P_BLANK

Figure 54. Input Sequence in PS Bit Interleaved Mode (EAV/SAV)

3

1035i

74.25MHz

CLKIN_B

Figure 51. Simultaneous HD and SD Input

PIXEL INPUT

FF

00

XY

Cb0

Y0

Cr0

Y1

DATA

If in simultaneous SD/HD input mode and the two clock phases

differ by less than 9.25 ns or more than 27.75 ns, the CLOCK

ALIGN bit [Address 0x01, Bit 3] must be set accordingly. If the

application uses the same clock source for both SD and PS, the

CLOCK ALIGN bit must be set since the phase difference

between both inputs is less than 9.25 ns.

WITH A 54MHz CLOCK, THE DATA IS LATCHED ON EVERY RISING EDGE.

Figure 55. Input Sequence in PS Bit Interleaved Mode (EAV/SAV)

MPEG2

DECODER

ADV7322

CLKIN_A

CLKIN_B

27MHz OR 54MHz

YCrCb

CLKIN_A

t

< 9.25ns OR

> 27.75ns

DELAY

INTERLACED

Figure 52. Clock Phase with Two Input Clocks

YCrCb

8

TO

Y[7:0]

PROGRESSIVE

P_VSYNC,

P_HSYNC,

P_BLANK

3

Figure 56. 10-Bit PS at 27 MHz or 54 MHz

Rev. PrA | Page 40 of 88

Preliminary Technical Data

ADV7322

Table 22. Input Configurations

Input Format

Total Bits

Input Video Input Pins

Subaddress Register Setting

ITU-R BT.656

8

4:2:2

YCrCb

S7–S0 [MSB = S7]

0x01

0x48

0x01

0x48

0x01

0x48

0x01

0x48

0x01

0x13

0x01

0x13

0x01

0x13

0x01

0x13

0x00

0x80

0x00

0x08

0x80

0x00

0x10

0x40

0x70

0x40

0x10

0x40

0x10

0x00

(4 options available)

See Table 21

YCrCb

Y7–Y0 [MSB = Y7]

16

4:2:2

4:4:4

Y

CrCb

Y

CrCb

YCrCb

S7–S0 [MSB = S7]

Y7–Y20[MSB = Y7]

Y7–Y0 [MSB = Y7]

C7–C0 [MSB = Y7]

Y7–Y0 [MSB = Y7]

PS Only

8 [27 MHz clock]

8 [54 MHz clock]

YCrCb

Y7–Y0 [MSB = Y7]

16

24

Y

CrCb

Y

Cb

Cr

Y

CrCb

Y

Cb

Cr

G

B

Y7–Y0 [MSB = Y7]

C7–C0 [MSB = C7]

Y7–Y0 [MSB = Y7]

C7–C0 [MSB = C7]

S7–S0 [MSB = S7]

Y7–Y0 [MSB = Y7]

C7–C0 [MSB = C7]

Y7–Y0 [MSB = Y7]

C7–C0 [MSB = C7]

S7–S0 [MSB = S7]

Y7–Y0 [MSB = Y7]

C7–C0 [MSB = C7]

S7–S0 [MSB = S7]

Y7–Y0 [MSB = Y7]

HDTV Only

16

24

4:2:2

4:4:4

0x01

0x13

0x01

0x13

0x20

0x40

0x20

0x00

HD RGB

24

4:4:4

0x01

0x13

0x15

0x01

0x13

0x48

0x01

0x13

0x48

0x10 or 0x20

0x00

0x02

0x40

0x00

0x30, 0x50, or 0x60

0x40

0x00

R

ITU-R BT.656 and PS

ITU-R BT.656 and PS or HDTV

8 (SD)

8 (PS)

4:2:2

YCrCb

8

16

4:2:2

YCrCb

Y

CrCb

S7–S0 [MSB = S7]

Y7–Y0 [MSB = Y7]

C7–C0 [MSB = C7]

Rev. PrA | Page 41 of 88

ADV7322

Preliminary Technical Data

FEATURES

OUTPUT CONFIGURATION

Table 23, Table 24, and Table 25 demonstrate what output signals are assigned to the DACs when the control bits are set accordingly.

Table 23. Output Configuration in SD Only Mode

RGB/YUV Output

SD DAC Output 1

SD DAC Output 2

0x02, Bit 5

0x42, Bit 2

0x42, Bit 1

DAC A

CVBS

G

DAC B

Luma

B

Luma

B

Luma

U

Luma

U

DAC C

DAC D

G

CVBS

G

DAC E

B

Luma

B

Luma

U

Luma

U

DAC F

0

1

0

1

0

1

0

1

0

1

0

1

0

1

Chroma

R

Chroma

R

Chroma

V

Chroma

V

R

Chroma

R

Chroma

V

Chroma

V

Chroma

G

CVBS

Y

CVBS

Y

CVBS

Luma

Luma/Chroma Swap 0x44, Bit 7

0

1

Table as above

Table above with all luma/chroma instances swapped

Table 24. Output Configuration in HD/PS Only Mode

HD/PS

HD/PS RGB Input RGB/YPrPb Output HD/PS Color

Input Format 0x15, Bit 1

0x02, Bit 5

Swap 0x15, Bit 3 DAC A DAC B DAC C DAC D DAC E DAC F

YCrCb 4:2:2

YCrCb 4:4:4

RGB 4:4:4

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

N/A

G

Y

B

R

Pb

Pr

B

R

B

Pr

Pb

R

Y

G

Y

R

B

Pb

Pr

B

R

B

Pr

Pb

R

B

R

Y

G

RGB 4:4:4

R

B

Table 25. Output Configuration in Simultaneous SD and HD/PS Only Mode

RGB/YPrPb Output

0x02, Bit 5

HD/PS Color Swap

0x15, Bit 3

Input Formats

DAC A

DAC B

DAC C

DAC D

DAC E DAC F

ITU-R.BT656 and HD

YCrCb in 4:2:2

ITU-R.BT656 and HD

YCrCb in 4:2:2

ITU-R.BT656 and HD

YCrCb in 4:2:2

ITU-R.BT656 and HD

YCrCb in 4:2:2

0

1

0

1

0

1

CVBS

Luma

Chroma

G

B

R

CVBS

G

Y

R

B

Pb

Pr

Pb

Rev. PrA | Page 42 of 88

Preliminary Technical Data

ADV7322

In async mode, the PLL must be turned off [Subaddress 0x00,

Bit 1 = 1]. Register 0x10 should be programmed to 0x01.

HD ASYNC TIMING MODE

[Subaddress 0x10, Bits 3 and 2]

Figure 57 and Figure 58 show examples of how to program the

ADV7322 to accept a high definition standard other than

SMPTE 293M, SMPTE 274M, SMPTE 296M, or ITU-R

BT.1358.

For any input data that does not conform to the standards

selectable in input mode, Subaddress 0x10, asynchronous

timing mode can be used to interface to the ADV7322. Timing

HSYNC VSYNC

BLANK

control signals for

,

, and

must be

programmed by the user. Macrovision and programmable

oversampling rates are not available in async timing mode.

Table 26 must be followed when programming the control signals

in async timing mode. For standards that do not require a trisync

P_BLANK

level,

must be tied low at all times.

Table 26. Async Timing Mode Truth Table

P_HSYNC P_VSYNC P_BLANK¹Reference

Reference in Figure 57 and Figure 58

1 —> 0

0

0 —> 1

1

0

0 or 1

0

0 —> 1

1 —> 0

50% point of falling edge of trilevel horizontal sync signal

25% point of rising edge of trilevel horizontal sync signal

50% point of falling edge of trilevel horizontal sync signal

50% start of active video

a

b

c

d

e

0 —> 1

0 or 1

50% end of active video

¹When async timing mode is enabled,

, Pin 25, becomes an active high input.

is set to active low at Address 0x10, Bit 6.

P_BLANK

CLK

P_HSYNC

PROGRAMMABLE

INPUT TIMING

P_VSYNC

P_BLANK

SET ADDRESS 0x14,

BIT 3 = 1

HORIZONTAL SYNC

ACTIVE VIDEO

ANALOG

OUTPUT

81

66

243

1920

a

b

c

d

e

Figure 57. Async Timing Mode—Programming Input Control Signals for SMPTE 295M Compatibility

CLK

P_HSYNC

0

1

P_VSYNC

P_BLANK

SET ADDRESS 0x14

BIT 3 = 1

HORIZONTAL SYNC

ACTIVE VIDEO

ANALOG OUTPUT

a

b

c

d

e

Figure 58. Async Timing Mode—Programming Input Control Signals for Bilevel Sync Signal

Rev. PrA | Page 43 of 88

ADV7322

Preliminary Technical Data

b. In subcarrier phase reset, a low-to-high transition on

the RTC_SCR_TR pin (Pin 31) will reset the

subcarrier phase to zero on the field following the

subcarrier phase reset when the SD RTC/TR/SCR

control bits at Address 0x44 are set to 01.

HD TIMING RESET

A timing reset is achieved by toggling the HD timing reset control

bit [Subaddress 0x14, Bit 0] from 0 to 1. In this state the horizontal

and vertical counters will remain reset.When this bit is set back to

0, the internal counters will commence counting again.

This reset signal must be held high for a minimum of

one clock cycle.

The minimum time the pin has to be held high is one clock

cycle; otherwise, this reset signal might not be recognized. This

timing reset applies to the HD timing counters only.

Since the field counter is not reset, it is recommended

that the reset signal is applied in Field 7 [PAL] or Field

3 [NTSC]. The reset of the phase will then occur on

the next field, i.e., Field 1, being lined up correctly with

the internal counters. The field count register at

Address 0x7B can be used to identify the number of

the active field.

SD REAL-TIME CONTROL, SUBCARRIER RESET,

AND TIMING RESET

[Subaddress 0x44, Bits 2 and 1]

Together with the RTC_SCR_TR pin and SD Mode Register 3

[Address 0x44, Bits 1 and 2], the ADV7322 can be used in (a)

timing reset mode, (b) subcarrier phase reset mode, or (c) RTC

mode.

c. In RTC mode, the ADV7322 can be used to lock to an

external video source. The real-time control mode

allows the ADV7322 to automatically alter the

subcarrier frequency to compensate for line length

variations. When the part is connected to a device that

outputs a digital data stream in the RTC format, such

as an ADV7183A video decoder (see Figure 61), the

part will automatically change to the compensated

subcarrier frequency on a line by line basis. This

digital data stream is 67 bits wide and the subcarrier is

contained in Bits 0 to 21. Each bit is two clock cycles

long. Write 0x00 into all four subcarrier frequency

registers when this mode is used.

a. A timing reset is achieved in a low-to-high transition

on the RTC_SCR_TR pin (Pin 31). In this state, the

horizontal and vertical counters will remain reset.

Upon releasing this pin (set to low), the internal

counters will commence counting again, the field

count will start on Field 1, and the subcarrier phase

will be reset.

The minimum time the pin must be held high is one

clock cycle; otherwise, this reset signal might not be

recognized. This timing reset applies to the SD timing

counters only.

DISPLAY

START OF FIELD 4 OR 8

F

PHASE = FIELD 4 OR 8

SC

307

310

313

320

NO TIMING RESET APPLIED

DISPLAY

START OF FIELD 1

F

PHASE = FIELD 1

SC

307

1

2

3

4

5

6

7

21

TIMING RESET PULSE

TIMING RESET APPLIED

Figure 59. Timing Reset Timing Diagram

Rev. PrA | Page 44 of 88

Preliminary Technical Data

ADV7322

DISPLAY

START OF FIELD 4 OR 8

F

PHASE = FIELD 4 OR 8

SC

307

NO F RESET APPLIED

310

313

320

SC

DISPLAY

START OF FIELD 4 OR 8

F

PHASE = FIELD 1

SC

307

310

313

320

F

RESET PULSE

SC

F

RESET APPLIED

SC

Figure 60. Subcarrier Reset Timing Diagram

ADV7322

CLKIN_A

DAC A

DAC B

DAC C

DAC D

DAC E

DAC F

LCC1

RTC_SCR_TR

GLL

COMPOSITE

ADV7183A

VIDEO

1

VIDEO

P17–P10

5

Y7–Y0/S7–S0

DECODER

4 BITS

RESERVED

14 BITS

H/L TRANSITION

COUNT START

LOW

SEQUENCE RESET

SUBCARRIER

PHASE

3

4

BIT

RESERVED

2

128

F

PLL INCREMENT

SC

13

0

21

19

0

RTC

6768

TIME SLOT 01

14

VALID INVALID

SAMPLE SAMPLE

8/LINE

LOCKED

CLOCK

5 BITS

RESERVED

NOTES

1

i.e., VCR OR CABLE

2

F

PLL INCREMENT IS 22 BITS LONG. VALUE LOADED INTO ADV7322 F DDS REGISTER IS F PLL INCREMENTS BITS 21:0

SC

SC SC

PLUS BITS 0:9 OF SUBCARRIER FREQUENCY REGISTERS. ALL ZEROS SHOULD BE WRITTEN TO THE SUBCARRIER FREQUENCY REGISTERS

OF THE ADV7322.

SEQUENCE BITꢀ

3

PAL: 0 = LINE NORMAL, 1 = LINE INVERTED ꢀ

NTSC: 0 = NO CHANGE

RESET ADV7322 DDS

4

5

SELECTED BY REGISTER ADDRESS 0x01 BIT 7

Figure 61. RTC Timing and Connections

Rev. PrA | Page 45 of 88

ADV7322

Preliminary Technical Data

signal usually occurs after the total number of lines/fields is

reached. Conventionally this means that the output video will

have corrupted field signals, one generated by the incoming

video and one generated when the internal lines/field counters

reach the end of a field.

RESET SEQUENCE

RESET

A reset is activated with a high-to-low transition on the

pin [Pin 33] according to the timing specifications. The

ADV7322 will revert to the default output configuration. Figure 62

RESET

illustrates the

timing sequence.

When the VCR FF/RW sync control is enabled [Subaddress

0x42, Bit 5], the lines/fields counters are updated according to

SD VCR FF/RW SYNC

VSYNC

the incoming

VSYNC

signal, and the analog output matches the

signal.

[Subaddress 0x42, Bit 5]

incoming

In DVD record applications where the encoder is used with a

decoder, the VCR FF/RW sync control bit can be used for

nonstandard input video, i.e., in fast forward or rewind modes.

This control is available in all slave timing modes except Slave

Mode 0.

In fast forward mode, the sync information at the start of a new

field in the incoming video usually occurs before the correct

number of lines/fields is reached; in rewind mode, this sync

RESET

DACs

XXXXXX

A, B, C

OFF

VALID VIDEO

DIGITAL TIMING SIGNALS SUPPRESSED

TIMING ACTIVE

DIGITAL TIMING

XXXXXX

PIXEL DATA

VALID

RESET

Figure 62.

Timing Sequence

Rev. PrA | Page 46 of 88

Preliminary Technical Data

ADV7322

VERTICAL BLANKING INTERVAL

SUBCARRIER FREQUENCY REGISTERS

The ADV7322 accepts input data that contains VBI data

[CGMS, WSS, VITS, and so on] in SD and HD modes.

[Subaddresses 0x4C to 0x4F]

Four 8-bit registers are used to set up the subcarrier frequency.

The value of these registers is calculated using the equation

For SMPTE 293M [525p] standards, VBI data can be inserted

on Lines 13 to 42 of each frame, or on Lines 6 to 43 for the

ITU-R BT.1358 [625p] standard.

Subcarrier Frequency Register =

Number of subcarrier periods in one video line

×2³²

For SD NTSC this data can be present on Lines 10 to 20, and in

PAL on Lines 7 to 22.

Number of 27 MHz clk cycles in one video line

where the sum is rounded to the nearest integer.

For example, in NTSC mode

If VBI is disabled [Address 0x11, Bit 4 for HD; Address 0x43,

Bit 4 for SD], VBI data is not present at the output and the

entire VBI is blanked. These control bits are valid in all master

and slave modes.

227.5

1716

⎛

⎜

⎝

⎞

⎟

⎠

Subcarrier Re gister Value =

×2³²= 569408543

In Slave Mode 0, if VBI is enabled, the blanking bit in the

EAV/SAV code is overwritten. It is possible to use VBI in this

timing mode as well.

where:

Subcarrier Register Value = 0x21F07C1F

SD F_SCRegister 0: 0x1F

SD F_SCRegister 1: 0x7C

SD F_SCRegister 2: 0xF0

SD F_SCRegister 3: 0x21

BLANK

In Slave Mode 1 or 2, the

control bit must be set to

enabled [Address 0x4A, Bit 3] to allow VBI data to pass through

the ADV7322. Otherwise, the ADV7322 automatically blanks

the VBI to standard.

See the MPU Port Description section for more details on how

to access the subcarrier frequency registers.

If CGMS is enabled and VBI is disabled, the CGMS data will

nevertheless be available at the output.

Programming the F_SC

See Appendix 1—Copy Generation Management System.

The Subcarrier Register Value is shared across 4 F_SCregisters as

shown above. To load the value into the encoder, users must

write to the F_SCregisters in sequence, starting with F_SC0. The

value is not loaded until the F_SC4 write is complete.

Note that the ADV7322 power-up value for F_SC0 = 0x1E. For

precise NTSC F_SC, write 0x1F to this register.

Rev. PrA | Page 47 of 88

ADV7322

Preliminary Technical Data

SQUARE PIXEL TIMING MODE

[Address 0x42, Bit 4]

In square pixel mode, the following timing diagrams apply.

ANALOG

VIDEO

EAV CODE

SAV CODE

C

b

C

r

8

0

F

A

B

A

B

A

B

8

0

C

b

C

r

F

0

X

Y

1

0

8

0

1

0

8

0

1

0

1

0

F

0

X

Y

C

b

C

r

Y

INPUT PIXELS

ANCILLARY DATA

(HANC)

4 CLOCK

NTSC/PAL M SYSTEM

(525 LINES/60Hz)

272 CLOCK

1280 CLOCK

1536 CLOCK

PAL SYSTEM

(625 LINES/50Hz)

344 CLOCK

START OF ACTIVE

VIDEO LINE

END OF ACTIVE

VIDEO LINE

Figure 63. EAV/SAV Embedded Timing

HSYNC

FIELD

PAL = 44 CLOCK CYCLES

NTSC = 44 CLOCK CYCLES

BLANK

PIXEL

DATA

Cr

Y

Cb

Y

PAL = 136 CLOCK CYCLES

NTSC = 208 CLOCK CYCLES

Figure 64. Active Pixel Timing

Rev. PrA | Page 48 of 88

Preliminary Technical Data

ADV7322

This filter has a cutoff frequency of about 2.7 MHz and –40 dB

at 3.8 MHz, as shown in Figure 65. This filter can be controlled

with Address 0x42, Bit 0.

FILTERS

Table 27 shows an overview of the programmable filters

available on the ADV7322.

EXTENDED UV FILTER MODE

Table 27. Selectable Filters

Filter

0

Subaddress

0x40

0x42

0x13

SD Luma LPF NTSC

SD Luma LPF PAL

SD Luma Notch NTSC

SD Luma Notch PAL

SD Luma SSAF

–10

–20

–30

–40

–50

–60

SD Luma CIF

SD Luma QCIF

SD Chroma 0.65 MHz

SD Chroma 1.0 MHz

SD Chroma 1.3 MHz

SD Chroma 2.0 MHz

SD Chroma 3.0 MHz

SD Chroma CIF

SD Chroma QCIF

SD UV SSAF

HD Chroma Input

HD Sinc Filter

0

1

2

3

4

5

6

FREQUENCY (MHz)

Figure 65. UV SSAF Filter

If this filter is disabled, the selectable chroma filters shown in

Table 28 can be used for the CVBS or luma/chroma signal.

Table 28. Internal Filter Specifications

Pass-Band

3 dB Bandwidth²

(MHz)

HD Chroma SSAF

Filter

Ripple¹(dB)

Luma LPF NTSC

Luma LPF PAL

Luma Notch NTSC

Luma Notch PAL

Luma SSAF

0.16

0.1

0.09

0.1

0.04

0.127

Monotonic

0.09

4.24

4.81

2.3/4.9/6.6

3.1/5.6/6.4

6.45

3.02

1.5

0.65

1

1.395

2.2

3.2

0.65

0.5

SD Internal Filter Response

[Subaddress 0x40 [7:2]; Subaddress 0x42, Bit 0]

The Y filter supports several different frequency responses

including two low-pass responses, two notch responses, an

extended (SSAF) response with or without gain boost

attenuation, a CIF response, and a QCIF response. The UV filter

supports several different frequency responses including six

low-pass responses, a CIF response, and a QCIF response, as

shown in Figure 35 and Figure 36.

Luma CIF

Luma QCIF

Chroma 0.65 MHz

Chroma 1.0 MHz

Chroma 1.3 MHz

Chroma 2.0 MHz

Chroma 3.0 MHz

Chroma CIF

0.048

Monotonic

If SD SSAF gain is enabled, there is the option of 12 responses

in the range −4 dB to +4 dB [Subaddress 0x47, Bit 4]. The

desired response can be chosen by the user by programming the

correct value via the I²C [Subaddress 0x62]. The variation of

frequency responses are shown in Figure 32 and Figure 33.

Chroma QCIF

¹Pass-band ripple is the maximum fluctuation from the 0 dB response in the

pass band, measured in dB. The pass band is defined to have 0 Hz to fc (Hz)

frequency limits for a low-pass filter, and 0 Hz to f1 (Hz) and f2 (Hz) to infinity

for a notch filter, where fc, f1, and f2 are the −3 dB points.

In addition to the chroma filters listed in Table 27, the

ADV7322 contains an SSAF filter specifically designed for and

applicable to the color difference component outputs, U and V.

²3 dB bandwidth refers to the −3 dB cutoff frequency.

Rev. PrA | Page 49 of 88

ADV7322

Preliminary Technical Data

PS/HD Sinc Filter

Table 29. Sample Color Values for EIA 770.2

Output Standard Selection

[Subaddress 0x13, Bit 3]

Sample Color

Y Value

235 (EB)

16 (10)

81 (51)

145 (91)

41 (29)

210 (D2)

170 (AA)

106 (6A)

Cr Value

128 (80)

240 (F0)

34 (22)

110 (6E)

146 (92)

16 (10)

Cb Value

128 (80)

90 (5A)

54 (36)

240 (F0)

16 (10)

0.5

White

Black

Red

Green

Blue

Yellow

Cyan

0.4

0.3

0.2

0.1

0

166 (A6)

202 (CA)

–0.1

–0.2

–0.3

–0.4

–0.5

Magenta

222 (DE)

RGB Matrix

[Subaddresses 0x03 to 0x09]

0

5

10

15

20

25

30

The internal RGB matrix automatically takes care of all YCrCb

to RGB scaling according to the input standard programmed in

the device as selected by input mode Register 0x01 [6:4]. Table 30

shows the options available in this Matrix.

FREQUENCY (MHz)

Figure 66. HD Sinc Filter Enabled

0.5

0.4

Note that it is not possible to do a color space conversion from

RGB-in to YPrPb-out. Also, it is not possible to input SD RGB.

0.3

Table 30. Matrix Conversion Options

HDTV/SD/PS

0.2

0.1

Reg 0x15, Bit 1

(RGB IN/YCrCb IN,

PS/HD Only)

0

Reg 0x02,Bit 5

Input Output (YUV/RGB OUT)

–0.1

–0.2

–0.3

–0.4

–0.5

YCrCb YPrPb

YCrCb RGB

1

0

1

RGB

0

5

10

15

20

25

30

Manual RGB Matrix Adjust Feature

FREQUENCY (MHz)

Normally, there is no need to enable this feature in Register

0x02, Bit 3, because the RGB Matrix automatically takes care of

color space conversion depending on the input mode chosen

(SD/PS,HD) and the polarity of RGB/YPrPb output in Register

0x02, Bit 5 (see Table 30). For this reason, manual RGB matrix

adjust feature is turned off by default.

Figure 67. HD Sinc Filter Disabled

COLOR CONTROLS AND RGB MATRIX

HD Y Level, HD Cr Level, HD Cb Level

[Subaddresses 0x16 to 0x18]

Three 8-bit registers at Addresses 0x16, 0x17, and 0x18 are used

to program the output color of the internal HD test pattern

generator, be it the lines of the cross hatch pattern or the

uniform field test pattern. They are not functional as color

controls on external pixel data input. For this purpose the RGB

matrix is used.

The Manual RGB matrix adjust feature is used in progressive

scan and high definition modes only and is used for custom

coefficient manipulation.

When the manual RGB matrix adjust feature is enabled, the

default values in Registers 0x05 to 0x09 are correct for HDTV

color space only. The color components are converted according

to the 1080i and 720p standards [SMPTE 274M, SMPTE

296M]:

The standard used for the values for Y and the color difference

signals to obtain white, black, and the saturated primary and

complementary colors conforms to the ITU-R BT.601-4 standard.

R = Y + 1.575Pr

Table 29 shows sample color values to be programmed into the

color registers when Output Standard Selection is set to EIA 770.2.

G = Y − 0.468Pr − 0.187Pb

B = Y + 1.855Pb

Rev. PrA | Page 50 of 88

Preliminary Technical Data

ADV7322

This is reflected in the preprogrammed values for GY = 0x138B,

GU = 0x93, GV = 0x3B, BU = 0x248, and RV = 0x1F0.

Upon power-up, the RGB matrix is programmed with the

default values in Table 31.

Table 31. RGB Matrix Default Values

Again if RGB matrix is enabled and another input standard is

used (SD or PS), the scale values for GY, GU, GV, BU, and RV

must be adjusted according to this input standard color space.

The user should consider the fact that the color component

conversion might use different scale values. For example,

SMPTE 293M uses the following conversion:

Address

Default

0x03

0x04

0x05

0x06

0x07

0x08

0x09

0x03

0xF0

0x4E

0x0E

0x24

0x92

0x7C

R = Y + 1.402Pr

G = Y – 0.714Pr – 0.344Pb

B = Y + 1.773Pb

When the manual RGB matrix adjust feature is not enabled, the

ADV7322 automatically scales YCrCb inputs to all standards

supported by this part as selected by input mode Register 0x01

[6:4].

The manual RGB matrix adjust feature can be used to control

the HD output levels in cases where the video output does not

conform to the standard due to altering the DAC output stages

such as termination resistors. The programmable RGB matrix is

used for external HD/PS data and is not functional when

internal test patterns are enabled.

SD Luma and Color Control

[Subaddresses 0x5C, 0x5D, 0x 5E, 0x 5F]

SD Y Scale, SD Cr Scale, and SD Cb Scale are three 10-bit-wide

control registers that scale the Y, Cb, and Cr output levels.

Adjusting Registers 0x05 to 0x09 requires the manual RGB

matrix adjust to be enabled [Register 0x02, Bit 3 =1].

Each of these registers represents the value required to scale the

Cb or Cr level from 0.0 to 2.0 and the Y level from 0.0 to 1.5 of

its initial level. The value of these 10 bits is calculated using the

following equation:

Programming the RGB Matrix

If custom manipulation of coefficients is required, The RGB

matrix is enabled in Address 0x02, Bit 3. The output should be

set to RGB [Address 0x02, Bit 5], sync on PrPb should be

disabled (default) [Address 0x15, Bit 2], and sync on RGB is

optional [Address 0x02, Bit 4].

Y, Cr, or Cb Scalar Value = Scale Factor × 512

For example,

Scale Factor = 1.18

GY at Addresses 0x03 and 0x05 control the green signal output

levels. BU at Addresses 0x04 and 0x08 control the blue signal

output levels, and RV at Addresses 0x04 and 0x09 control the

red signal output levels. To control YPrPb output levels, YUV

output should be enabled [Address 0x02, Bit 5]. In this case GY

[Address 0x05; Address 0x03, Bits 0 and 1] is used for the Y

output, RV [Address 0x09; Address 0x04, Bits 0 and 1] is used

for the Pr output, and BU [Address 0x08; Address 0x04, Bits 2

and 3] is used for the Pb output.

Y, Cb, or Cr Scale Value = 1.18 × 512 = 665.6

Y, Cb, or Cr Scale Value = 665 (rounded to the nearest

integer)

Y, Cb, or Cr Scale Value = 1010 0110 01b

Address 0x5C, SD LSB Register = 0x15

Address 0x5D, SD Y Scale Register = 0xA6

Address 0x5E, SD Cb Scale Register = 0xA6

Address 0x5F, SD Cr Scale Register = 0xA6

If RGB output is selected, the RGB matrix scaler uses the

following equations:

Note that this feature affects all interlaced output signals, i.e.,

CVBS, Y-C, YPrPb, and RGB.

G = GY × Y + GU × Pb + GV × Pr

B = GY × Y + BU × Pb

SD Hue Adjust Value

[Subaddress 0x60]

R = GY × Y + RV × Pr

The hue adjust value is used to adjust the hue on the composite

and chroma outputs.

If YPrPb output is selected, the following equations are used:

Y = GY × Y

These eight bits represent the value required to vary the hue of

the video data, i.e., the variance in phase of the subcarrier

during active video with respect to the phase of the subcarrier

during the color burst. The ADV7322 provides a range of 22.5°

U = BU × Pb

V = RV × Pr

Rev. PrA | Page 51 of 88

ADV7322

Preliminary Technical Data

increments of 0.17578125°. For normal operation (zero

adjustment), this register is set to 0x80. Values 0xFF and 0x00

represent the upper and lower limits (respectively) of

adjustment attainable.

For example,

1. To add +20 IRE brightness level to an NTSC signal with

pedestal , write 0x28 to Address 0x61, SD brightness.

0x[SD Brightness Value] =

Hue Adjust (°) = 0.17578125° (HCR_d− 128) for positive hue

adjust value.

0x[IRE Value × 2.015631] =

For example, to adjust the hue by +4°, write 0x97 to the Hue

Adjust Value register:

0x[20 × 2.015631] = 0x[40.31262] = 0x28

2. To add –7 IRE brightness level to a PAL signal, write 0x72 to

Address 0x61, SD brightness.

4

⎛

⎜

⎝

⎞

⎟

⎠

+ 128 = 105d = 0x97 .

0.17578125

[IRE Value| × 2.075631

where the sum is rounded to the nearest integer.

[7 × 2.015631] = [14.109417] = 0001110b

To adjust the hue by −4°, write 0x69 to the Hue Adjust Value

register:

[0001110] into twos complement = [1110010]b = 0x72

Table 32. Brightness Control Values¹

−4

⎛

⎜

⎝

⎞

⎟

⎠

+ 128 = 105d = 0x69

Setup Level In

NTSC with

Pedestal

Setup Level In

NTSC No

Pedestal

Setup

Level In

PAL

0.17578125

SD

Brightness

where the sum is rounded to the nearest integer.

SD Brightness Control

22.5 IRE

15 IRE

7.5 IRE

0 IRE

15 IRE

7.5 IRE

0 IRE

15 IRE

7.5 IRE

0 IRE

0x1E

0x0F

0x00

0x71

[Subaddress 0x61]

–7.5 IRE

The brightness is controlled by adding a programmable setup

level onto the scaled Y data. This brightness level may be added

onto the scaled Y data. For NTSC with pedestal, the setup can

vary from 0 IRE to 22.5 IRE. For NTSC without pedestal and

PAL, the setup can vary from −7.5 IRE to +15 IRE.

¹Values in the range from 0x3F to 0x44 might result in an invalid output

signal.

The brightness control register is an 8-bit register. Seven bits of

this 8-bit register are used to control the brightness level. This

brightness level can be a positive or negative value.

Rev. PrA | Page 52 of 88

Preliminary Technical Data

ADV7322

Double buffering can be activated on the following HD

SD Brightness Detect

registers: HD Gamma A and Gamma B curves and HD CGMS

registers.

[Subaddress 0x7A]

The ADV7322 allows monitoring of the brightness level of the

incoming video data. Brightness detect is a read-only register.

Double buffering can be activated on the following SD registers:

SD Gamma A and Gamma B curves, SD Y Scale, SD U Scale, SD

V Scale, SD Brightness, SD Closed Captioning, and SD

Macrovision Bits 5 to 0.

Double Buffering

[Subaddress 0x13, Bit 7; Subaddress 0x48, Bit 2]

Double buffered registers are updated once per field on the

falling edge of the VSYNC signal. Double buffering improves

the overall performance since modifications to register settings

will not be made during active video, but takes effect on the

start of the active video.

NTSC WITHOUT PEDESTAL

100 IRE

+7.5 IRE

–7.5 IRE

0 IRE

POSITIVE SETUP

VALUE ADDED

NEGATIVE SETUP

VALUE ADDED

NO SETUP

VALUE ADDED

Figure 68. Examples of Brightness Control Values

Rev. PrA | Page 53 of 88

ADV7322

Preliminary Technical Data

Table 33. DAC Gain Control

PROGRAMMABLE DAC GAIN CONTROL

DAC

Current

(mA)

DACs A, B, and C are controlled by REG 0A.

Reg 0x0A or

0x0B

% Gain

7.5000%

7.3820%

7.3640%

...

Note

DACs D, E, and F are controlled by REG 0B.

0100 0000 (0x40)

0011 1111 (0x3F)

0011 1110 (0x3E)

...

4.658

4.653

4.648

...

The I²C control registers will adjust the output signal gain up or

down from its absolute level.

CASE A

...

GAIN PROGRAMMED IN DAC OUTPUT LEVEL

REGISTERS, SUBADDRESS 0x0A, 0x0B

0000 0010 (0x02)

0000 0001 (0x01)

0000 0000 (0x00)

4.43

4.38

4.33

0.0360%

0.0180%

0.0000%

700mV

(I²C Reset Value,

Nominal)

1111 1111 (0xFF)

1111 1110 (0xFE)

...

4.25

4.23

...

−0.0180%

−0.0360%

...

1100 0010 (0xC2) 4.018

1100 0001 (0xC1) 4.013

1100 0000 (0xC0) 4.008

−7.3640%

−7.3820%

−7.5000%

300mV

NEGATIVE GAIN PROGRAMMED IN

CASE B

DAC OUTPUT LEVEL REGISTERS,

SUBADDRESS 0x0A, 0x0B

700mV

GAMMA CORRECTION

[Subaddresses 0x24 to 0x37 for HD,

Subaddresses 0x66 to 0x79 for SD]

Gamma correction is available for SD and HD video. For each

standard, there are twenty 8-bit-wide registers. They are used to

program the gamma correction curves A and B. HD gamma

curve A is programmed at Addresses 0x24 to 0x2D, and HD

gamma curve B is programmed at 0x2E to 0x7. SD gamma

curve A is programmed at Addresses 0x66 to 0x6F, and SD

gamma curve B is programmed at Addresses 0x70 to 0x79.

300mV

Figure 69. Programmable DAC Gain—Positive and Negative Gain

In case A, the video output signal is gained. The absolute level of

the sync tip and blanking level both increase with respect to the

reference video output signal. The overall gain of the signal is

increased from the reference signal.

Generally gamma correction is applied to compensate for the

nonlinear relationship between signal input and brightness level

output (as perceived on the CRT). It can also be applied

wherever nonlinear processing is used.

In case B, the video output signal is reduced. The absolute level

of the sync tip and blanking level both decrease with respect to

the reference video output signal. The overall gain of the signal

is reduced from the reference signal.

Gamma correction uses the function

γ

Signal_OUT

=

(

Signal_IN

)

where γ = gamma power factor.

The range of this feature is specified for 7.5% of the nominal

output from the DACs. For example, if the output current of the

DAC is 4.33 mA, the DAC tune feature can change this output

current from 4.008 mA (−7.5%) to 4.658 mA (+7.5%).

Gamma correction is performed on the luma data only. The

user may choose either of two curves, curve A or curve B. At

any one time, only one of these curves can be used.

The reset value of the vid_out_ctrl registers is 0x00; therefore,

nominal DAC current is output. The following table is an

example of how the output current of the DACs varies for a

nominal 4.33 mA output current.

The response of the curve is programmed at 10 predefined

locations. In changing the values at these locations, the gamma

curve can be modified. Between these points, linear

interpolation is used to generate intermediate values.

Considering the curve to have a total length of 256 points, the

10 locations are at 24, 32, 48, 64, 80, 96, 128, 160, 192, and 224.

Locations 0, 16, 240, and 255 are fixed and cannot be changed.

Rev. PrA | Page 54 of 88

Preliminary Technical Data

ADV7322

GAMMA CORRECTION BLOCK OUTPUT TO A RAMP INPUT

For the length of 16 to 240, the gamma correction curve has to

be calculated as follows:

300

250

y = xγ

SIGNAL OUTPUT

where:

200

150

100

50

0.5

y = gamma corrected output

x = linear input signal

γ = gamma power factor

To program the gamma correction registers, calculate the seven

values for y using the following formula:

SIGNAL INPUT

x_(n−16)

⎡

⎤

y_n=

γ ×(240 −16) + 16

⎢

⎥

0

(240 −16)

0

50

100

150

LOCATION

200

250

⎣

⎦

where:

Figure 70. Signal Input (Ramp) and Signal Output for Gamma 0.5

x(n − 16) = Value for x along x axis at points

n = 24, 32, 48, 64, 80, 96, 128, 160, 192, or 224

y_n= Value for y along the y axis, which must be written into the

gamma correction register

GAMMA CORRECTION BLOCK TO A RAMP INPUT FOR

VARIOUS GAMMA VALUES

300

For example,

250

y₂₄= [(8/224)0.5 × 224] + 16 = 58

y₃₂= [(16/224)0.5 × 224] + 16 = 76

y₄₈= [(32/224)0.5 × 224] + 16 = 101

y₆₄= [(48/224)0.5 × 224] + 16 =120

y₈₀= [(64 / 224)0.5 × 224] + 16 =136

y₉₆= [(80 / 224)0.5 × 224] + 16 = 150

0.3

200

0.5

150

1.5

100

1.8

50

0

50

100

150

LOCATION

200

250

y

₁₂₈= [(112 / 224)0.5 × 224] + 16 = 174

₁₆₀= [(144 / 224)0.5 × 224] + 16 = 195

₁₉₂= [(176 / 224)0.5 × 224] + 16 = 214

₂₂₄= [(208 / 224)0.5 × 224] + 16 = 232

Figure 71. Signal Input (Ramp) and Selectable Output Curves

where the sum of each equation is rounded to the nearest

integer.

The gamma curves in Figure 70 and Figure 71 are examples only;

any user-defined curve is acceptable in the range of 16 to 240.

Rev. PrA | Page 55 of 88

ADV7322

Preliminary Technical Data

The derivative of the incoming signal is compared to the three

programmable threshold values: HD adaptive filter threshold A,

B, and C. The recommended threshold range is from 16 to 235,

although any value in the range of 0 to 255 can be used.

HD SHARPNESS FILTER AND ADAPTIVE FILTER

CONTROLS

[Subaddresses 0x20, 0x38 to 0x3D]

There are three filter modes available on the ADV7322:

sharpness filter mode and two adaptive filter modes.

The edges can then be attenuated with the settings in HD

adaptive filter gain 1, 2, and 3 registers and HD sharpness filter

gain register.

HD Sharpness Filter Mode

To enhance or attenuate the Y signal in the frequency ranges

shown in Figure 72, the following register settings must be used:

HD sharpness filter must be enabled and HD adaptive filter

enable must be set to disabled.

According to the settings of the HD adaptive filter mode

control, there are two adaptive filter modes available:

1. Mode A is used when adaptive filter mode is set to 0.

In this case, Filter B (LPF) will be used in the adaptive

filter block. Also, only the programmed values for

Gain B in the HD sharpness filter gain and HD

adaptive filter gain 1, 2, and 3 are applied when

needed. The Gain A values are fixed and cannot be

changed.

To select one of the 256 individual responses, the corresponding

gain values, which range from –8 to +7, for each filter must be

programmed into the HD sharpness filter gain register at

Address 0x20.

HD Adaptive Filter Mode

The HD adaptive filter threshold A, B, and C registers, the HD

adaptive filter gain 1, 2, and 3 registers, and the HD sharpness

gain register are used in adaptive filter mode. To activate the

adaptive filter control, the HD sharpness filter and the HD

adaptive filter must be enabled.

2. Mode B is used when adaptive filter mode is set to 1.

In this mode, a cascade of Filter A and Filter B is used.

Both settings for Gain A and Gain B in the HD

sharpness filter gain and HD adaptive filter gain 1, 2,

and 3 become active when needed.

SHARPNESS AND ADAPTIVE FILTER CONTROL BLOCK

1.5

1.4

1.3

1.2

1.5

1.4

1.3

1.2

1.6

1.5

1.4

1.1

1.0

1.1

1.0

INPUT

SIGNAL:

STEP

ꢀ

1.3

1.2

1.1

1.0

0.9

0.8

0.7

0.6

0.5

0.9

0.8

0.7

0.6

0.5

0

2

4

6

8

10

12

FREQUENCY (MHz)

FILTER A RESPONSE (Gain Ka)

FREQUENCY (MHz)

FILTER B RESPONSE (Gain Kb)

FREQUENCY (MHz)

FREQUENCY RESPONSE IN SHARPNESS

FILTER MODE WITH Ka = 3 AND Kb = 7

Figure 72. Sharpness and Adaptive Filter Control Block

Rev. PrA | Page 56 of 88

Preliminary Technical Data

ADV7322

HD SHARPNESS FILTER AND ADAPTIVE FILTER

APPLICATION EXAMPLES

Table 34. Sharpness Control

HD Sharpness Filter Application

Address

0x00

0x01

0x02

0x10

0x11

0x20

Register Setting

Reference¹

The HD sharpness filter can be used to enhance or attenuate the

Y video output signal. The following register settings were used

to achieve the results shown in Figure 73. Input data was

generated by an external signal source.

0xFC

0x10

0x20

0x00

0x81

0x00

0x08

0x04

a

b

c

d

e

f

0x40

0x80

0x22

¹See Figure 73.

d

e

a

b

R2

R4

1

R1

c

f

1

R2

CH1 500mV

M 4.00µs

9.99978ms

CH1

ALL FIELDS

CH1 500mV

REF A

M 4.00µs

1 9.99978ms

CH1

ALL FIELDS

REF A

500mV 4.00µs

1

500mV 4.00µs

Figure 73. HD Sharpness Filter Control with Different Gain Settings for HS Sharpness Filter Gain Values

Rev. PrA | Page 57 of 88

ADV7322

Preliminary Technical Data

When changing the adaptive filter mode to Mode B

Adaptive Filter Control Application

[Address 0x15, Bit 6], the output shown in Figure 76 can be

obtained.

Figure 74 and Figure 75 show typical signals to be processed by

the adaptive filter control block.

∆: 674mV

@: 446mV

∆: 332ns

∆: 692mV

@: 446mV

∆: 332ns

@: 12.8ms

Figure 76. Output Signal from Adaptive Filter Control

Figure 74. Input Signal to Adaptive Filter Control

∆: 692mV

@: 446mV

∆: 332ns

SD DIGITAL NOISE REDUCTION

[Subaddresses 0x63, 0x64, 0x65]

@: 12.8ms

DNR is applied to the Y data only. A filter block selects the high

frequency, low amplitude components of the incoming signal

[DNR input select]. The absolute value of the filter output is

compared to a programmable threshold value ['DNR threshold

control]. There are two DNR modes available: DNR mode and

DNR sharpness mode.

In DNR mode, if the absolute value of the filter output is

smaller than the threshold, it is assumed to be noise. A

programmable amount [coring gain border, coring gain data] of

this noise signal will be subtracted from the original signal. In

DNR sharpness mode, if the absolute value of the filter output is

less than the programmed threshold, it is assumed to be noise,

as before. Otherwise, if the level exceeds the threshold, now

being identified as a valid signal, a fraction of the signal [coring

gain border, coring gain data] will be added to the original

signal to boost high frequency components and sharpen the

video image.

Figure 75. Output Signal after Adaptive Filter Control

The register settings in Table 35 were used to obtain the results

shown in Figure 75, i.e., to remove the ringing on the Y signal.

Input data was generated by an external signal source.

Table 35. Register Settings for Figure 76

Address

0x00

0x01

0x02

0x10

0x11

0x15

0x20

0x38

0x39

0x3A

0x3B

0x3C

0x3D

Register Setting

0xFC

0x38

0x20

0x00

0x81

0x80

0x00

0xAC

0x9A

0x88

0x28

0x3F

In MPEG systems, it is common to process the video

information in blocks of 8 pixels × 8 pixels for MPEG2 systems,

or 16 pixels × 16 pixels for MPEG1 systems [block size control].

DNR can be applied to the resulting block transition areas that

are known to contain noise. Generally, the block transition area

contains two pixels. It is possible to define this area to contain

four pixels [border area].

It is also possible to compensate for variable block positioning

or differences in YCrCb pixel timing with the use of the DNR

block offset

0x64

The digital noise reduction registers are three 8-bit registers.

They are used to control the DNR processing.

Rev. PrA | Page 58 of 88

Preliminary Technical Data

ADV7322

output, which lies above the threshold range. The result is added

to the original signal.

DNR MODE

DNR CONTROL

BLOCK SIZE CONTROL

BORDER AREA

BLOCK OFFSET

APPLY DATA

APPLY BORDER

CORING GAIN CORING GAIN

GAIN

CORING GAIN DATA

CORING GAIN BORDER

O X X X X X X O O X X X X X X O

NOISE

SIGNAL PATH

OFFSET CAUSED

BY VARIATIONS IN

INPUT TIMING

INPUT FILTER

BLOCK

O X X X X X X O O X X X X X X O

FILTER

SUBTRACT SIGNAL

IN THRESHOLD

RANGE FROM

DNR27 – DNR24 = 0x01 O X X X X X X O O X X X X X X O

OUTPUT

Y DATA

< THRESHOLD?

INPUT

ORIGINAL SIGNAL

–

Figure 78. DNR Offset Control

FILTER OUTPUT

> THRESHOLD

+

DNR OUT

DNR THRESHOLD

MAIN SIGNAL PATH

[Address 0x64, Bits 5 to 0]

DNR

DNR CONTROL

SHARPNESS

These six bits are used to define the threshold value in the range

of 0 to 63. The range is an absolute value.

MODE

BLOCK SIZE CONTROL

BORDER AREA

BLOCK OFFSET

GAIN

BORDER AREA

CORING GAIN DATA

CORING GAIN BORDER

[Address 0x64, Bit 6]

NOISE

SIGNAL PATH

INPUT FILTER

BLOCK

When this bit is set to Logic 1, the block transition area can be

defined to consist of four pixels. If this bit is set to Logic 0, the

border transition area consists of two pixels, where one pixel

refers to two clock cycles at 27 MHz.

FILTER

ADD SIGNAL

ABOVE

THRESHOLD

RANGE FROM

ORIGINAL SIGNAL

OUTPUT

Y DATA

INPUT

> THRESHOLD?

+

FILTER OUTPUT

< THRESHOLD

720 × 485 PIXELS

+

2-PIXEL

BORDER

(NTSC)

DNR OUT

DATA

MAIN SIGNAL PATH

Figure 77. DNR Block Diagram

CORING GAIN BORDER

[Address 0x63, Bits 3 to 0]

These four bits are assigned to the gain factor applied to border

areas. In DNR mode, the range of gain values is 0 to 1 in

increments of 1/8. This factor is applied to the DNR filter

output, which lies below the set threshold range. The result is

then subtracted from the original signal.

8 × 8 PIXEL BLOCK

Figure 79. DNR Border Area

BLOCK SIZE CONTROL

[Address 0x64, Bit 7]

In DNR sharpness mode, the range of gain values is 0 to 0.5 in

increments of 1/16. This factor is applied to the DNR filter

output, which lies above the threshold range. The result is added

to the original signal.

This bit is used to select the size of the data blocks to be

processed. Setting the block size control function to Logic 1

defines a 16 pixel × 16 pixel data block, and Logic 0 defines an

8 pixel × 8 pixel data block, where one pixel refers to two clock

cycles at 27 MHz.

CORING GAIN DATA

[Address 0x63, Bits 7 to 4]

DNR INPUT SELECT CONTROL

These four bits are assigned to the gain factor applied to the luma

data inside the MPEG pixel block. In DNR mode, the range of

gain values is 0 to 1 in increments of 1/8. This factor is applied

to the DNR filter output, which lies below the set threshold

range. The result is then subtracted from the original signal.

[Address 0x65, Bits 2 to 0]

Three bits are assigned to select the filter, which is applied to the

incoming Y data. The signal that lies in the pass band of the

selected filter is the signal that will be DNR processed. Figure 80

shows the filter responses selectable with this control.

In DNR sharpness mode, the range of gain values is 0 to 0.5 in

increments of 1/16. This factor is applied to the DNR filter

Rev. PrA | Page 59 of 88

ADV7322

Preliminary Technical Data

original signal, since this data is assumed to be valid data and

not noise. The overall effect is that the signal will be boosted

(similar to using Extended SSAF filter).

1.0

FILTER D

0.8

BLOCK OFFSET CONTROL

FILTER C

0.6

0.4

0.2

0

[Address 0x65, Bits 7 to 4]

Four bits are assigned to this control, which allows a shift of the

data block of 15 pixels maximum. Consider the coring gain

positions fixed. The block offset shifts the data in steps of one

pixel such that the border coring gain factors can be applied at the

same position regardless of variations in input timing of the data.

FILTER B

FILTER A

1

2

3

0

4

5

6

SD ACTIVE VIDEO EDGE

FREQUENCY (Hz)

[Subaddress 0x42, Bit 7]

Figure 80. DNR Input Select

DNR MODE CONTROL

When the active video edge feature is enabled, the first three

pixels and the last three pixels of the active video on the luma

channel are scaled so that maximum transitions on these pixels

are not possible. The scaling factors are ×1/8, ×1/2, and ×7/8.

All other active video passes through unprocessed.

[Address 0x65, Bit 4]

This bit controls the DNR mode selected. Logic 0 selects DNR

mode; Logic 1 selects DNR sharpness mode.

DNR works on the principle of defining low amplitude, high

frequency signals as probable noise and subtracting this noise

from the original signal.

SAV/EAV STEP EDGE CONTROL

The ADV7322 has the capability of controlling fast rising and

falling signals at the start and end of active video to minimize

ringing.

In DNR mode, it is possible to subtract a fraction of the signal

that lies below the set threshold, assumed to be noise, from the

original signal. The threshold is set in DNR Register 1.

An algorithm monitors SAV and EAV and determines when the

edges are rising or falling too fast. The result is reduced ringing

at the start and end of active video for fast transitions.

Subaddress 0x42, Bit 7 = 1, enables this feature.

When DNR sharpness mode is enabled, it is possible to add a

fraction of the signal that lies above the set threshold to the

LUMA CHANNEL WITH

ACTIVE VIDEO EDGE

DISABLED

LUMA CHANNEL WITH

ACTIVE VIDEO EDGE

ENABLED

100 IRE

0 IRE

100 IRE

87.5 IRE

50 IRE

12.5 IRE

0 IRE

Figure 81. Example of Active Video Edge Functionality

Rev. PrA | Page 60 of 88

Preliminary Technical Data

ADV7322

VOLTS

IRE:FLT

100

0.5

50

0

F2

L135

–50

2

0

4

6

8

10

12

Figure 82. Address 0x42, Bit 7 = 0

VOLTS

IRE:FLT

100

0.5

50

0

F2

L135

–50

0

–2

2

4

6

8

10

12

Figure 83. Address 0x42, Bit 7 = 1

Rev. PrA | Page 61 of 88

ADV7322

Preliminary Technical Data

BOARD DESIGN AND LAYOUT

CIRCUIT FREQUENCY RESPONSE

0

DAC TERMINATION AND LAYOUT

CONSIDERATIONS

0

–10

–20

–30

–40

–50

–60

–70

–80

24n

21n

18n

15n

12n

9n

–30

MAGNITUDE (dB)

The ADV7322 contains an on-board voltage reference. The

ADV7322 can be used with an external V_REF(AD1580).

–60

–90

The R_SETresistors are connected between the R_SETpins and

AGND and are used to control the full-scale output current and,

therefore, the DAC voltage output levels. For full-scale output,

R_SETmust have a value of 3040 Ω. The RSET values should not

be changed. R_LOADhas a value of 300 Ω for full-scale output.

–120

–150

–180

–210

–240

PHASE (Deg)

GROUP DELAY (sec)

6n

VIDEO OUTPUT BUFFER AND OPTIONAL

OUTPUT FILTER

3n

0

1M

10M

100M

1G

Output buffering on all six DACs is necessary to drive output

devices, such as SD or HD monitors. Analog Devices produces a

range of suitable op amps for this application, for example the

AD8061. More information on line driver buffering circuits is

given in the relevant op amps’ data sheets.

FREQUENCY (Hz)

Figure 85. Filter Plot for Output Filter for SD, 16× Oversampling

4.7µH

DAC

OUTPUT

3

4

75Ω

BNC

OUTPUT

6.8pF

600Ω

1

An optional analog reconstruction low-pass filter (LPF) may be

required as an anti-imaging filter if the ADV7322 is connected

to a device that requires this filtering.

600

Ω

560

Ω

560

Ω

The filter specifications vary with the application.

Figure 86. Example of Output Filter for PS, 8× Oversampling

Table 36. External Filter Requirements

Cutoff

Frequency

Application Oversampling (MHz)

Attenuation

–50 dB @

(MHz)

DAC

OUTPUT

3

470nH 220nH

SD

PS

HDTV

2×

16×

1×

8×

1×

2×

>6.5

>12.5

>30

20.5

209.5

14.5

203.5

44.25

118.5

75Ω

BNC

OUTPUT

1

3

4

300Ω

75Ω

1

33pF

82pF

4

500Ω

>30

Figure 87. Example of Output Filter for HDTV, 2× Oversampling

10µH

DAC

OUTPUT

3

4

75Ω

BNC

OUTPUT

Table 37. Possible Output Rates from the ADV7322

600Ω

22pF

600Ω

1

Input Mode Address

0x01, Bits 6 to 4

PLL Address

0x00, Bit 1

Output Rate

(MHz)

560Ω

SD Only

Off

On

Off

On

27 (2×)

216 (16×)

27 (1×)

560Ω

PS Only

Figure 84. Example of Output Filter for SD, 16× Oversampling

216 (8×)

HDTV Only

Off On

74.25 (1×)

148.5 (2×)

Rev. PrA | Page 62 of 88

Preliminary Technical Data

ADV7322

CIRCUIT FREQUENCY RESPONSE

0

There should be a separate analog ground plane and a separate

digital ground plane.

480

400

320

240

160

80

18n

16n

–10

MAGNITUDE (dB)

Power planes should encompass a digital power plane and an

analog power plane. The analog power plane should contain the

DACs and all associated circuitry, V_REFcircuitry. The digital

power plane should contain all logic circuitry.

–20

–30

–40

–50

–60

–70

–80

–90

14n

12n

10n

8n

GROUP DELAY (Sec)

PHASE (Deg)

The analog and digital power planes should be individually

connected to the common power plane at a single point

through a suitable filtering device, such as a ferrite bead.

0

6n

–80

–160

–240

4n

DAC output traces on a PCB should be treated as transmission

lines. It is recommended that the DACs be placed as close as

possible to the output connector, with the analog output traces

being as short as possible (less than 3 inches). The DAC

termination resistors should be placed as close as possible to the

DAC outputs and should overlay the PCB’s ground plane. As

well as minimizing reflections, short analog output traces will

reduce noise pickup due to neighboring digital circuitry.

2n

0

1M

10M

100M

1G

FREQUENCY (Hz)

Figure 88. Filter Plot for Output Filter for PS, 8× Oversampling

CIRCUIT FREQUENCY RESPONSE

480

0

–10

–20

–30

–40

–50

–60

18n

15n

12n

9n

360

MAGNITUDE (dB)

To avoid crosstalk between the DAC outputs, it is recommended

that as much space as possible be left between the tracks of the

individual DAC output pins. The addition of ground tracks

between outputs is also recommended.

240

GROUP DELAY (sec)

120

Supply Decoupling

0

Noise on the analog power plane can be further reduced by the

use of decoupling capacitors.

6n

PHASE (Deg)

–120

3n

Optimum performance is achieved by the use of 10 nF and

0.1 µF ceramic capacitors. Each group of V_AA, V_DD, or V_{DD_IO}

pins should be individually decoupled to ground. This should

be done by placing the capacitors as close as possible to the

device with the capacitor leads as short as possible, thus

minimizing lead inductance.

–240

0

1M

10M

100M

1G

FREQUENCY (Hz)

Figure 89. Filter Plot for Output Filter for HDTV, 2× Oversampling

PCB BOARD LAYOUT

A 1 µF tantalum capacitor is recommended across the V_AA

supply in addition to 10 nF ceramic. See the circuit layout in

Figure 90.

The ADV7322 is optimally designed for lowest noise

performance, both radiated and conducted noise. To

complement the excellent noise performance of the ADV7322,

it is imperative that great care be given to the PC board layout.

Digital Signal Interconnect

The digital signal lines should be isolated as much as possible

from the analog outputs and other analog circuitry. Digital

signal lines should not overlay the analog power plane.

The layout should be optimized for lowest noise on the

ADV7322 power and ground lines. This can be achieved by

shielding the digital inputs and providing good decoupling. The

lead length between groups of V_AAand AGND, V_DDand DGND,

and V_{DD_IO}and GND_IO pins should be kept as short as

possible to minimized inductive ringing.

Due to the high clock rates used, avoid long clock lines to the

ADV7322 to minimize noise pickup.

Any active pull-up termination resistors for the digital inputs

should be connected to the digital power plane and not the

analog power plane.

It is recommended that a 4-layer printed circuit board is used,

with power and ground planes separating the layer of the signal

carrying traces of the components and solder side layer.

Component placement should be carefully considered in order

to separate noisy circuits, such as crystal clocks, high speed logic

circuitry, and analog circuitry.

Analog Signal Interconnect

Locate the ADV7322 as close as possible to the output

connectors to minimize noise pickup and reflections due to

impedance mismatch.

Rev. PrA | Page 63 of 88

ADV7322

Preliminary Technical Data

For optimum performance, the analog outputs should each be

source and load terminated, as shown in Figure 90. The

termination resistors should be as close as possible to the

ADV7322 to minimize reflections.

For optimum performance, it is recommended that all

decoupling and external components relating to the ADV7322

be located on the same side of the PCB and as close as possible

to the ADV7322. Any unused inputs should be tied to ground.

POWER SUPPLY DECOUPLING

FOR EACH POWER SUPPLY GROUP

V

AA

DD

+

V

10nF

1µF

AA AA

0.1µF

V

DD_IO

10, 56

V

AA

DD_IO

5kΩ

45

36

41

1

10nF

1.1kΩ

COMP1, 2

V

DD

AA

DD_IO

2

19

I C

46

44

V

REF

ADV7322

RECOMMENDED EXTERNAL

AD1580 FOR OPTIMUM

PERFORMANCE

100nF

S0–S7

DAC A

DAC B

DAC C

DAC D

DAC E

DAC F

300Ω

50

49

S_HSYNC

S_VSYNC

43

42

39

38

37

48 S_BLANK

300Ω

C0–C7

UNUSED

INPUTS

SHOULD BE

GROUNDED

Y0–Y7

63

23

CLKIN_B

P_HSYNC

V

24 P_VSYNC

25 P_BLANK

AA

4.7kΩ

V

DD_IO

33

32

RESET

5kΩ

100Ω

+

2

22

21

I C BUS

SCLK

SDA

4.7µF

CLKIN_A

100Ω

V

AA

820pF

34

EXT_LF

V

DD_IO

20

35

ALSB

5kΩ

R

680Ω

SET2

3.9nF

SELECTION HERE

DETERMINES

DEVICE ADDRESS

3040Ω

47

R

SET1

GND_ IO

64

AGND DGND

40

11, 57

Figure 90. ADV7322 Circuit Layout

Rev. PrA | Page 64 of 88

Preliminary Technical Data

ADV7322

APPENDIX 1—COPY GENERATION MANAGEMENT SYSTEM

PS CGMS

FUNCTION OF CGMS BITS

Data Registers 2 to 0

For Word 0 to 6 bits, Word 1 to 4 bits, and Word 2 to 6 bits CRC

6 bits,

[Subaddresses 0x21, 0x22, 0x23]

CRC Polynomial = x6 + x + 1

525p

Using the vertical blanking interval 525p system, 525p CGMS

conforms to the CGMS-A EIA-J CPR1204-1 (March 1998)

transfer method of video identification information and to the

IEC61880 (1998) 525p/60 video system’s analog interface for the

video and accompanying data.

where default is preset to 111111.

720p System

CGMS data is applied to Line 24 of the luminance vertical

blanking interval.

1080i System

When PS CGMS is enabled [Subaddress 0x12, Bit 6 = 1], CGMS

data is inserted on Line 41. The 525p CGMS data registers are at

Addresses 0x21, 0x22, and 0x23.

CGMS data is applied to Line 19 and Line 582 of the luminance

vertical blanking interval.

CGMS FUNCTIONALITY

625p

If SD CGMS CRC [Address 0x59, Bit 4] or PS/HD CGMS CRC

[Subaddress 0x12, Bit 7] is set to Logic 1, the last six bits, C19 to

C14, which comprise the 6-bit CRC check sequence, are

calculated automatically on the ADV7322 based on the lower

14 bits (C0 to C13) of the data in the data registers and output

with the remaining 14 bits to form the complete 20 bits of the

CGMS data. The calculation of the CRC sequence is based on

the polynomial ×6 + x + 1 with a preset value of 111111. If SD

CGMS CRC [Address 0x59, Bit 4] and PS/HD CGMS CRC

[Address 0x12, Bit 7] are set to Logic 0, all 20 bits (C0 to C19)

are output directly from the CGMS registers (no CRC is

calculated, must be calculated by the user).

The 625p CGMS conforms to the IEC62375 (2004) 625p/50

video system’s analog interface for the video and accompanying

data using the vertical blanking interval.

When PS CGMS is enabled [Subaddress 0x12, Bit 6 = 1], CGMS

data is inserted on Line 43. The 625p CGMS data registers are at

Addresses 0x22, and 0x23.

HD CGMS

[Address 0x12, Bit 6]

The ADV7322 supports Copy Generation Management System

(CGMS) in HDTV mode (720p and 1080i) in accordance with

EIAJ CPR-1204-2.

The HD CGMS data registers are found at Addresses 0x021,

0x22, and 0x23.

SD CGMS

Data Registers 2 to 0

[Subaddresses 0x59, 0x5A, 0x5B]

The ADV7322 supports Copy Generation Management System

(CGMS), conforming to the standard. CGMS data is

transmitted on Line 20 of the odd fields and Line 283 of even

fields. Bits C/W05 and C/W06 control whether CGMS data is

output on odd and even fields. CGMS data can be transmitted

only when the ADV7322 is configured in NTSC mode. The

CGMS data is 20 bits long, and the function of each of these bits

is as shown in the following table. The CGMS data is preceded

by a reference pulse of the same amplitude and duration as a

CGMS bit; see Figure 93.

Rev. PrA | Page 65 of 88

ADV7322

Preliminary Technical Data

CRC SEQUENCE

+700mV

REF

BIT1 BIT2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .BIT20

70% ± 10%

C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19

0mV

–300mV

21.2µs ± 0.22µs

22T

5.8µs ± 0.15µs

6T

T = 1/(f_H× 33) = 963ns

f_H= HORIZONTAL SCAN FREQUENCY

T ± 30ns

Figure 91. Progressive Scan 525p CGMS Waveform (Line 41)

R = RUN-IN

S = START CODE

PEAK WHITE

C0

LSB

C13

MSB

R

S

C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12

500mV ± 25mV

SYNC LEVEL

13.7µs

5.5µs ± 0.125µs

Figure 92. Progressive Scan 625p CGMS-A Waveform (Line 43)

+100 IRE

CRC SEQUENCE

REF

+70 IRE

C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19

0 IRE

–40 IRE

49.1µs ± 0.5µs

11.2µs

2.235µs ± 20ns

Figure 93. Standard Definition CGMS Waveform

Rev. PrA | Page 66 of 88

Preliminary Technical Data

ADV7322

CRC SEQUENCE

+700mV

REF

BIT1 BIT2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BIT20

70% ± 10%

C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19

0mV

T ± 30ns

–300mV

17.2µs ± 160ns

4T

22T

3.128µs ± 90ns

T = 1/(f_H× 1650/58) = 781.93ns

f_H= HORIZONTAL SCAN FREQUENCY

1H

Figure 94. HDTV 720p CGMS Waveform

CRC SEQUENCE

+700mV

REF

BIT1 BIT2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BIT20

70% ± 10%

C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19

0mV

T ± 30ns

–300mV

22.84µs ± 210ns

4T

22T

4.15µs ± 60ns

T = 1/(f × 2200/77) = 1.038µs

H

f

= HORIZONTAL SCAN FREQUENCY

H

1H

Figure 95. HDTV 1080i CGMS Waveform

Rev. PrA | Page 67 of 88

ADV7322

Preliminary Technical Data

APPENDIX 2—SD WIDE SCREEN SIGNALING

data is preceded by a run-in sequence and a start code; see

Figure 95. If SD WSS [Address 0x59, Bit 7] is set to Logic 1, it

enables the WSS data to be transmitted on Line 23. The latter

[Subaddresses 0x59, 0x5A, 0x5B]

The ADV7322 supports wide screen signaling (WSS)

conforming to the standard. WSS data is transmitted on Line 23.

WSS data can be transmitted only when the device is

configured in PAL mode. The WSS data is 14 bits long, and the

function of each of these bits is shown in Table 38. The WSS

HSYNC

portion of Line 23 (42.5 s from the falling edge of

) is

available for the insertion of video. It is possible to blank the

WSS portion of Line 23 with Subaddress 0x61, Bit 7.

Table 38. Function of WSS Bits

Bit

Description

Bit 0 to Bit 2

Aspect Ratio/Format/Position

Bit 3

B0

0

1

0

1

0

1

0

Odd Parity Check of Bit 0 to Bit 2

B1

0

1

0

1

B2

0

1

B3

1

0

1

0

1

0

Aspect Ratio

4:3

14:9

16:9

>16:9

14:9

Format

Position

N/A

Center

Top

Center

Top

Center

N/A

Full Format

Letterbox

Full Format

N/A

1

16:9

1

0

16:9

B4

0

1

Camera Mode

Film Mode

B5

0

Standard Coding

1

Motion Adaptive Color Plus

B6

0

No Helper

1

Modulated Helper

Reserved

B7

B9

0

B10

0

No Open Subtitles

1

0

1

0

1

Subtitles in Active Image Area

Subtitles out of Active Image Area

Reserved

B11

0

1

No Surround Sound Information

Surround Sound Mode

Reserved

B12

B13

Reserved

500mV

RUN-IN

SEQUENCE

ACTIVE

VIDEO

START

CODE

W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 W10 W11 W12 W13

11.0µs

38.4µs

42.5µs

Figure 96. WSS Waveform Diagram

Rev. PrA | Page 68 of 88

Preliminary Technical Data

ADV7322

APPENDIX 3—SD CLOSED CAPTIONING

[Subaddresses 0x51 to 0x54]

FCC Code of Federal Regulations (CFR) 47 section 15.119 and

EIA608 describe the closed captioning information for Lines 21

and 284.

The ADV7322 supports closed captioning conforming to the

standard television synchronizing waveform for color

transmission. Closed captioning is transmitted during the

blanked active line time of Line 21 of the odd fields and Line

284 of the even fields.

The ADV7322 uses a single buffering method. This means that

the closed captioning buffer is only 1 byte deep; therefore, there

will be no frame delay in outputting the closed captioning data,

unlike other 2-byte-deep buffering systems. The data must be

loaded one line before it is output on Line 21 and Line 284. A

Closed captioning consists of a 7-cycle sinusoidal burst that is

frequency and phase locked to the caption data. After the clock

run-in signal, the blanking level is held for two data bits and is

followed by Logic 1 start bit. Sixteen bits of data follow the start

bit. These consist of two 8-bit bytes, seven data bits, and one

odd parity bit. The data for these bytes is stored in the SD closed

captioning registers [Addresses 0x53 to 0x54].

VSYNC

typical implementation of this method is to use

to

interrupt a microprocessor, which in turn will load the new data

(two bytes) in every field. If no new data is required for

transmission, 0s must be inserted in both data registers; this is

called nulling. It is also important to load control codes, all of

which are double bytes, on Line 21, or a TV will not recognize

them. If there is a message like “Hello World” that has an odd

number of characters, it is important to pad it out to even to get

“end of caption” 2-byte control code to land in the same field.

The ADV7322 also supports the extended closed captioning

operation, which is active during even fields and encoded on

Scan Line 284. The data for this operation is stored in the SD

closed captioning registers [Addresses 0x51 to 0x52].

All clock run-in signals and timing to support closed captioning

on Lines 21 and 284 are generated automatically by the

ADV7322. All pixels inputs are ignored during Lines 21 and 284

if closed captioning is enabled.

10.5

±

0.25µ

s

12.91µs

7 CYCLES OF

0.5035MHz

CLOCK RUN-IN

TWO 7-BIT + PARITY

ASCII CHARACTERS

(DATA)

P

A

R

I

T

Y

P

A

R

I

T

Y

S

T

A

R

T

D0–D6

50 IRE

40 IRE

BYTE 0

BYTE 1

REFERENCE COLOR BURST

(9 CYCLES)

FREQUENCY = F = 3.579545MHz

SC

AMPLITUDE = 40 IRE

10.003µs

27.382

µ

s

33.764µs

Figure 97. Closed Captioning Waveform, NTSC

Rev. PrA | Page 69 of 88

ADV7322

Preliminary Technical Data

APPENDIX 4—TEST PATTERNS

The ADV7322 can generate SD and HD test patterns.

T

2

CH2 200mV

M 10.0

µ

s

A CH2 1.20V

CH2 100mV

M 10.0µs

CH2

EVEN

T

30.6000µs

T

1.82600ms

Figure 98. NTSC Color Bars

Figure 101. PAL Black Bar [–21 mV, 0 mV, 3.5 mV, 7 mV, 10.5 mV, 14 mV,

18 mV, 23 mV]

T

2

CH2 200mV

M 10.0µs

A CH2 1.21V

CH2 200mV

M 4.0µs

CH2

EVEN

T

30.6000µs

T

1.82944ms

Figure 102. 525p Hatch Pattern

Figure 99. PAL Color Bars

T

2

CH2 200mV

M 4.0µs

CH2

EVEN

CH2 100mV

M 10.0µs

CH2

EVEN

T

1.84208ms

T

1.82380ms

Figure 103. 625p Hatch Pattern

Figure 100. NTSC Black Bar [–21 mV, 0 mV, 3.5 mV, 7 mV, 10.5 mV, 14 mV,

18 mV, 23 mV]

Rev. PrA | Page 70 of 88

Preliminary Technical Data

ADV7322

T

2

CH2 200mV

M 4.0µs

CH2

EVEN

CH2 100mV

M 4.0µs

CH2

EVEN

T

1.82872ms

T

1.82936ms

Figure 106. 525p Black Bar [−35 mV, 0 mV, 7 mV, 14 mV, 21 mV,

28 mV, 35 mV]

Figure 104. 525p Field Pattern

T

2

CH2 100mV

M 4.0µs

CH2

EVEN

CH2 200mV

M 4.0µs

CH2

EVEN

T

1.84176ms

T

1.84176ms

Figure 105. 625p Field Pattern

Figure 107. 625p Black Bar [−35 mV, 0 mV, 7 mV, 14 mV,

21 mV, 28 mV, 5 mV]

Rev. PrA | Page 71 of 88

ADV7322

Preliminary Technical Data

The register settings in Table 39 are used to generate an SD

NTSC CVBS output on DAC A, S-video on DACs B and C, and

YPrPb on DACs D, E, and F. Upon power-up, the subcarrier

registers are programmed with the appropriate values for NTSC.

All other registers are set as normal/default.

The register settings in Table 41 are used to generate a 525p

hatch pattern on DAC D, E, and F. All other registers are set as

normal/default.

Table 41. 525p Test Pattern Register Writes.

Subaddress

Register Setting

Table 39. NTSC Test Pattern Register Writes

Ox00

0xFC

Subaddress

Register Setting

0x01

0x10

0x00

0xFC

0x10

0x00

0x40

0x10

0x11

0x05

0x42

0x40

0x16

0xA0

0x44

0x4A

0x40 (internal test pattern on)

0x08

0x17

0x18

0x80

For PAL CVBS output on DAC A, the same settings are used,

except that Subaddress 0x40 is programmed to 0x11 and the Fsc

registers are programmed as shown in Table 40.

For 625p hatch pattern on DAC D, the same register settings are

used except that Subaddress 0x10 = 0x18.

Table 40. PAL Fsc Register Writes

Subaddress

Description

Register Setting

0x4C

0x4D

0x4E

0x4F

Fsc0

Fsc1

Fsc2

Fsc3

0xCB

0x8A

0x09

0x2A

Note that when programming the Fsc registers, the user must

write the values in the sequence Fsc0, Fsc1, Fsc2, Fsc3. The full

Fsc value to be written is only accepted after the Fsc3 write is

complete.

Rev. PrA | Page 72 of 88

Preliminary Technical Data

ADV7322

APPENDIX 5—SD TIMING MODES

[Subaddress 0x4A]

MODE 0 (CCIR-656)—SLAVE OPTION

(TIMING REGISTER 0 TR0 = X X X X X 0 0 0)

The ADV7322 is controlled by the SAV (start active video) and

EAV (end active video) time codes in the pixel data. All timing

information is transmitted using a 4-byte synchronization

pattern. A synchronization pattern is sent immediately before

S_VSYNC

(if not used) pins should be tied high

and after each line during active picture and retrace.

S_HSYNC S_BLANK

,

, and

during this mode. Blank output is available.

ANALOG

VIDEO

EAV CODE

SAV CODE

C

b

C

r

8

0

F

A

B

A

B

A

B

8

0

C

b

C

r

F

0

X

Y

1

0

8

0

1

0

8

0

1

0

1

0

F

0

X

Y

C

b

C

r

Y

INPUT PIXELS

ANCILLARY DATA

(HANC)

4 CLOCK

1440 CLOCK

268 CLOCK

NTSC/PAL M SYSTEM

(525 LINES/60Hz)

280 CLOCK

PAL SYSTEM

(625 LINES/50Hz)

START OF ACTIVE

VIDEO LINE

END OF ACTIVE

VIDEO LINE

Figure 108. SD Slave Mode 0

Rev. PrA | Page 73 of 88

ADV7322

Preliminary Technical Data

MODE 0 (CCIR-656)—MASTER OPTION

(TIMING REGISTER 0 TR0 = X X X X X 0 0 1)

The ADV7322 generates H, V, and F signals required for the

SAV (start active video) and EAV (end active video) time codes

S_HSYNC

, and the F bit is output on

in the CCIR656 standard. The H bit is output on

S_BLANK

, the

V bit is output on

S_VSYNC

.

DISPLAY

VERTICAL BLANK

4

522

523

524

525

1

2

3

5

6

7

8

10

11

20

21

22

9

H

V

ODD FIELD

EVEN FIELD

F

DISPLAY

VERTICAL BLANK

283

285

284

260

261

262

263

264

265

266

267

268

269

270

271

272

273

274

H

V

F

ODD FIELD

EVEN FIELD

Figure 109. SD Master Mode 0, NTSC

Rev. PrA | Page 74 of 88

Preliminary Technical Data

ADV7322

DISPLAY

VERTICAL BLANK

622

623

624

625

4

22

23

1

2

3

5

6

7

21

H

V

ODD FIELD

EVEN FIELD

F

DISPLAY

VERTICAL BLANK

318

334

335

336

309

310

311

312

313

314

315

316

317

319

320

H

V

F

ODD FIELD

EVEN FIELD

Figure 110. SD Master Mode 0, PAL

ANALOG

VIDEO

H

F

V

Figure 111. SD Master Mode 0, Data Transitions

Rev. PrA | Page 75 of 88

ADV7322

Preliminary Technical Data

MODE 1—SLAVE OPTION

(TIMING REGISTER 0 TR0 = X X X X X 0 1 0)

In this mode, the ADV7322 accepts horizontal sync and

HSYNC

odd/even field signals. When

field input indicates a new frame, i.e., vertical retrace. The

BLANK BLANK

is low, a transition of the

signal is optional. When the

input is disabled,

ADV7322 automatically blanks all normally blank lines as per

HSYNC

, and FIELD on

S_HSYNC BLANK

,

CCIR-624.

S_BLANK

is input on

on

S_VSYNC

.

DISPLAY

VERTICAL BLANK

522

523

524

525

20

21

22

3

4

5

7

9

10

11

1

2

6

8

HSYNC

BLANK

FIELD

ODD FIELD

EVEN FIELD

DISPLAY

VERTICAL BLANK

283

285

284

260

261

262

263

264

265

266

267

268

269

270

271

272

273

274

HSYNC

BLANK

FIELD

ODD FIELD EVEN FIELD

Figure 112. SD Slave Mode 1 (NTSC)

Rev. PrA | Page 76 of 88

Preliminary Technical Data

ADV7322

MODE 1—MASTER OPTION

(TIMING REGISTER 0 TR0 = X X X X X 0 1 1)

In this mode, the ADV7322 can generate horizontal sync and

HSYNC

odd/even field signals. When

field input indicates a new frame, i.e., vertical retrace. The blank

BLANK

is low, a transition of the

signal is optional. When the

input is disabled,

ADV7322 automatically blanks all normally blank lines as per

CCIR-624. Pixel data is latched on the rising clock edge

HSYNC

following the timing signal transitions.

is output on the

S_HSYNC BLANK

S_BLANK

S_VSYNC

, and FIELD on .

,

on

DISPLAY

VERTICAL BLANK

3

4

5

7

622

623

624

625

1

2

6

21

22

23

HSYNC

BLANK

FIELD

ODD FIELD

EVEN FIELD

DISPLAY

VERTICAL BLANK

309

310

311

312

313

314

315

316

318

319

320

317

334

335

336

HSYNC

BLANK

FIELD

ODD FIELD

EVEN FIELD

Figure 113. SD Slave Mode 1 (PAL)

HSYNC

FIELD

PAL = 12

×

CLOCK/2

NTSC = 16

× CLOCK/2

BLANK

PIXEL

DATA

Cr

Y

Cb

Y

PAL = 132

×

CLOCK/2

NTSC = 122

× CLOCK/2

Figure 114. SD Timing Mode 1—Odd/Even Field Transitions Master/Slave

Rev. PrA | Page 77 of 88

ADV7322

Preliminary Technical Data

MODE 2— SLAVE OPTION

(TIMING REGISTER 0 TR0 = X X X X X 1 0 0)

In this mode, the ADV7322 accepts horizontal and vertical sync

HSYNC

VSYNC

signals. A coincident low transition of both

and

low

VSYNC

inputs indicates the start of an odd field. A

HSYNC

transition when

is high indicates the start of an even

field. The BLANK signal is optional. When the BLANK input is

disabled, ADV7322 automatically blanks all normally blank

HSYNC

S_HSYNC

lines as per CCIR-624.

is input on

S_VSYNC

, BLANK

S_BLANK

VSYNC

on

, and

on

.

DISPLAY

VERTICAL BLANK

522

523

524

525

1

3

2

4

5

7

8

20

21

22

6

10

11

9

HSYNC

BLANK

VSYNC

ODD FIELD

EVEN FIELD

DISPLAY

VERTICAL BLANK

283

285

284

260

261

262

263

264

265

266

267

268

269

270

271

272

273

274

HSYNC

BLANK

VSYNC

EVEN FIELD

ODD FIELD

Figure 115. SD Slave Mode 2 (NTSC)

DISPLAY

VERTICAL BLANK

4

622

623

624

625

1

2

3

5

6

7

21

22

23

HSYNC

BLANK

VSYNC

EVEN FIELD

ODD FIELD

DISPLAY

VERTICAL BLANK

309

310

311

312

313

314

315

316

318

319

320

317

334

335

336

HSYNC

BLANK

VSYNC

EVEN FIELD

ODD FIELD

Figure 116. SD Slave Mode 2 (PAL)

Rev. PrA | Page 78 of 88

Preliminary Technical Data

ADV7322

MODE 2—MASTER OPTION

(TIMING REGISTER 0 TR0 = X X X X X 1 0 1)

In this mode, the ADV7322 can generate horizontal and vertical

HSYNC

sync signals. A coincident low transition of both

VSYNC

and

inputs indicates the start of an odd field.

VSYNC HSYNC

A

low transition when

is high indicates the

signal is optional. When the

input is disabled, the ADV7322 automatically blanks all

BLANK

start of an even field. The

BLANK

HSYNC

S_BLANK

, and

normally blank lines as per CCIR-624.

is output on

VSYNC S_VSYNC

.

S_HSYNC BLANK

,

on

HSYNC

VSYNC

PAL = 12

×

CLOCK/2

NTSC = 16

×

BLANK

PIXEL

DATA

Cb

Cr

Y

PAL = 132

×

CLOCK/2

NTSC = 122

×

Figure 117. SD Timing Mode 2 Even-to-Odd Field Transition Master/Slave

HSYNC

VSYNC

PAL = 864 × CLOCK/2

NTSC = 858 × CLOCK/2

PAL = 12 × CLOCK/2

NTSC = 16 × CLOCK/2

BLANK

PIXEL

DATA

Cb

Y

Cr

Y

Cb

PAL = 132 × CLOCK/2

NTSC = 122 × CLOCK/2

Figure 118. SD Timing Mode 2 Odd-to-Even Field Transition

Rev. PrA | Page 79 of 88

ADV7322

Preliminary Technical Data

MODE 3—MASTER/SLAVE OPTION

(TIMING REGISTER 0 TR0 = X X X X X 1 1 0 OR

X X X X X 1 1 1)

In this mode, the ADV7322 accepts or generates horizontal sync

HSYNC

and odd/even field signals. When

of the field input indicates a new frame, i.e., vertical retrace. The

BLANK BLANK

is high, a transition

signal is optional. When the

ADV7322 automatically blanks all normally blank lines as per

HSYNC

input is disabled,

CCIR-624.

is output in master mode and input in slave

S_VSYNC BLANK

S_BLANK

VSYNC

mode on

S_VSYNC

,

on

, and

on

.

DISPLAY

VERTICAL BLANK

522

523

524

525

1

4

20

21

22

10

11

2

3

5

6

7

8

9

HSYNC

BLANK

FIELD

EVEN FIELD ODD FIELD

DISPLAY

VERTICAL BLANK

283

285

284

260

261

262

263

264

265

266

267

268

269

270

271

272

273

274

HSYNC

BLANK

FIELD

ODD FIELD EVEN FIELD

Figure 119. SD Timing Mode 3 (NTSC)

DISPLAY

VERTICAL BLANK

622

623

624

625

1

2

3

4

5

6

7

21

22

23

HSYNC

BLANK

FIELD

EVEN FIELD ODD FIELD

DISPLAY

VERTICAL BLANK

309

310

311

312

313

314

315

316

318

319

320

317

334

335

336

HSYNC

BLANK

FIELD

EVEN FIELD ODD FIELD

Figure 120. SD Timing Mode 3 (PAL)

Rev. PrA | Page 80 of 88

Preliminary Technical Data

APPENDIX 6—HD TIMING

ADV7322

DISPLAY

FIELD 1

VERTICAL BLANKING INTERVAL

1124 1125

1

2

3

4

5

6

7

8

20

21

22

560

P_VSYNC

P_HSYNC

DISPLAY

VERTICAL BLANKING INTERVAL

FIELD 2

561

562

563

564

565

566

567

568

569

570

583

584

585

1123

P_VSYNC

P_HSYNC

HSYNC

VSYNC

Input Timing

Figure 121. 1080i

and

Rev. PrA | Page 81 of 88

ADV7322

Preliminary Technical Data

APPENDIX 7—VIDEO OUTPUT LEVELS

HD YPrPb OUTPUT LEVELS

EIA-770.2, STANDARD FOR Y

EIA-770.3, STANDARD FOR Y

OUTPUT VOLTAGE

INPUT CODE

940

OUTPUT VOLTAGE

940

700mV

64

300mV

EIA-770.3, STANDARD FOR Pr/Pb

OUTPUT VOLTAGE

EIA-770.2, STANDARD FOR Pr/Pb

OUTPUT VOLTAGE

960

512

64

960

600mV

700mV

512

64

700mV

Figure 122. EIA 770.2 Standard Output Signals (525p/625p)

Figure 124. EIA 770.3 Standard Output Signals (1080i/720p)

EIA-770.1, STANDARD FOR Y

Y–OUTPUT LEVELS FOR

FULL INPUT SELECTION

INPUT CODE

1023

OUTPUT VOLTAGE

INPUT CODE

OUTPUT VOLTAGE

782mV

940

700mV

714mV

64

300mV

286mV

Pr/Pb–OUTPUT LEVELS FOR

FULL INPUT SELECTION

OUTPUT VOLTAGE

INPUT CODE

1023

EIA-770.1, STANDARD FOR Pr/Pb

OUTPUT VOLTAGE

960

700mV

512

64

300mV

Figure 123. EIA 770.1 Standard Output Signals (525p/625p)

Figure 125. Output Levels for Full Input Selection

Rev. PrA | Page 82 of 88

Preliminary Technical Data

ADV7322

RGB OUTPUT LEVELS

Pattern: 100%/75% Color Bars

700mV

525mV

700mV

525mV

300mV

700mV

525mV

700mV

525mV

300mV

700mV

525mV

700mV

525mV

300mV

Figure 126. PS RGB Output Levels

Figure 128. SD RGB Output Levels—RGB Sync Disabled

700mV

525mV

700mV

525mV

300mV

0mV

300mV

0mV

525mV

300mV

0mV

300mV

0mV

525mV

300mV

0mV

300mV

0mV

Figure 127. PS RGB Output Levels—RGB Sync Enabled

Figure 129. SD RGB Output Levels—RGB Sync Enabled

Rev. PrA | Page 83 of 88

ADV7322

Preliminary Technical Data

YPrPb LEVELS—SMPTE/EBU N10

Pattern: 100% Color Bars

700mV

Figure 130. Pb Levels—NTSC

Figure 133. Pr Levels—PAL

700mV

300mV

Figure 131. Pb Levels—PAL

Figure 134. Y Levels—NTSC

700mV

300mV

Figure 135. Y Levels—PAL

Figure 132. Pr Levels—NTSC

Rev. PrA | Page 84 of 88

Preliminary Technical Data

ADV7322

VOLTS

0.6

VOLTS IRE:FLT

100

0.4

0.2

0

0.5

50

0

–0.2

0

F1

–50

10

L608

L76

0

20

30

MICROSECONDS

PRECISION MODE OFF

40

50

60

10

20

30

40

50

60

NOISE REDUCTION: 0.00dB

APL = 39.1%

625 LINE NTSC NO FILTERING

SLOW CLAMP TO 0.00 AT 6.72µs

MICROSECONDS

PRECISION MODE OFF

APL = 44.5%

525 LINE NTSC

SYNCHRONOUS SYNC = A

FRAMES SELECTED 1, 2

SYNCHRONOUS SOUND-IN-SYNC OFF

FRAMES SELECTED 1, 2, 3, 4

SLOW CLAMP TO 0.00V AT 6.72µs

Figure 136. NTSC Color Bars 75%

Figure 139. PAL Color Bars 75%

VOLTS IRE:FLT

VOLTS

0.5

0.4

50

0.2

0

–0.2

–0.4

–50

–0.5

F1

L76

L575

20

0

10

20

30

40

50

60

10

30

40

50

60

NOISE REDUCTION: 15.05dB MICROSECONDS

MICROSECONDS NO BUNCH SIGNAL

PRECISION MODE OFF

APL NEEDS SYNC-SOURCE.

525 LINE NTSC NO FILTERING

SLOW CLAMP TO 0.00 AT 6.72µs

PRECISION MODE OFF

APL NEEDS SYNC-SOURCE.

625 LINE PAL NO FILTERING

SLOW CLAMP TO 0.00 AT 6.72µs

SYNCHRONOUS SYNC = B

FRAMES SELECTED 1, 2

SYNCHRONOUS SOUND-IN-SYNC OFF

FRAMES SELECTED 1

Figure 140. PAL Chroma

Figure 137. NTSC Chroma

VOLTS

0.5

VOLTS IRE:FLT

0.6

0.4

50

0

0.2

0

–0.2

F2

L238

L575

20

0

10

30

40

50

60

70

10

20

30

40

50

60

MICROSECONDS NO BUNCH SIGNAL

PRECISION MODE OFF

NOISE REDUCTION: 15.05dB MICROSECONDS

APL NEEDS SYNC-SOURCE.

625 LINE PAL NO FILTERING

APL = 44.3%

PRECISION MODE OFF

SYNCHRONOUS SOUND-IN-SYNC OFF

FRAMES SELECTED 1

525 LINE NTSC NO FILTERING

SLOW CLAMP TO 0.00 AT 6.72µs

SYNCHRONOUS SYNC = SOURCE

FRAMES SELECTED 1, 2

SLOW CLAMP TO 0.00 AT 6.72µs

Figure 138. NTSC Luma

Figure 141. PAL Luma

Rev. PrA | Page 85 of 88

ADV7322

Preliminary Technical Data

APPENDIX 8—VIDEO STANDARDS

0

DATUM

H

SMPTE 274M

ANALOG WAVEFORM

DIGITAL HORIZONTAL BLANKING

272T

*1

4T

1920T

DIGITAL

ACTIVE LINE

ANCILLARY DATA

(OPTIONAL) OR BLANKING CODE

EAV CODE

SAV CODE

F

0

F

0

C

r

C

INPUT PIXELS

Y

V

Y

b

r

H*

4 CLOCK

192

0

2199

SAMPLE NUMBER

2112

2116 2156

44

188

2111

FVH* = FVH AND PARITY BITS

SAV/EAV: LINE 1–562: F = 0

SAV/EAV: LINE 563–1125: F = 1

SAV/EAV: LINE 1–20; 561–583; 1124–1125: V = 1

SAV/EAV: LINE 21–560; 584–1123: V = 0

FOR A FRAME RATE OF 30Hz: 40 SAMPLES

FOR A FRAME RATE OF 25Hz: 480 SAMPLES

Figure 142. EAV/SAV Input Data Timing Diagram—SMPTE 274M

SMPTE 293M

ANALOG WAVEFORM

ANCILLARY DATA

(OPTIONAL)

DIGITAL

SAV CODE

F

EAV CODE

F

ACTIVE LINE

F

0

F

0

C

b

C

r

C

r

INPUT PIXELS

V

Y

V

Y

H*

4 CLOCK

853 857

SAMPLE NUMBER

719

723 736

DATUM

799

0

719

0

H

DIGITAL HORIZONTAL BLANKING

FVH* = FVH AND PARITY BITS

SAV: LINE 43–525 = 200H

SAV: LINE 1–42 = 2AC

EAV: LINE 43–525 = 274H

EAV: LINE 1–42 = 2D8

Figure 143. EAV/SAV Input Data Timing Diagram—SMPTE 293M

Rev. PrA | Page 86 of 88

Preliminary Technical Data

ADV7322

ACTIVE

VIDEO

ACTIVE

VIDEO

VERTICAL BLANK

522 523 524 525

1

2

5

6

7

8

9

12

13

14

15

16

42

43

44

Figure 144. SMPTE 293M (525p)

ACTIVE

VIDEO

ACTIVE

VIDEO

VERTICAL BLANK

12

13

1

2

5

6

7

8

9

43

44

45

622 623

624 625

4

10

11

Figure 145. ITU-R BT.1358 (625p)

DISPLAY

VERTICAL BLANKING INTERVAL

1

2

3

4

5

6

7

747

748

749

750

26

27

744

745

8

25

Figure 146. SMPTE 296M (720p)

DISPLAY

VERTICAL BLANKING INTERVAL

FIELD 1

560

1124

1125

1

2

3

4

5

6

7

8

20

21

22

DISPLAY

VERTICAL BLANKING INTERVAL

FIELD 2

561

562

563

564

565

566

567

568

569

570

583

584

585

1123

Figure 147. SMPTE 274M (1080i)

Rev. PrA | Page 87 of 88

ADV7322

Preliminary Technical Data

OUTLINE DIMENSIONS

0.75

0.60

0.45

12.00

BSC SQ

1.60

MAX

64

49

48

1

SEATING

PLANE

PIN 1

10.00

BSC SQ

TOP VIEW

(PINS DOWN)

10°

6°

2°

1.45

1.40

1.35

0.20

0.09

VIEW A

7°

3.5°

16

33

32

0.15

0.05

0°

17

SEATING

PLANE

0.08 MAX

COPLANARITY

0.27

0.22

0.17

0.50

BSC

VIEW A

ROTATED 90° CCW

COMPLIANT TO JEDEC STANDARDS MS-026BCD

Figure 148. 64-Lead Low Profile Quad Flat Package [LQFP]

(ST-64-2)

Dimensions shown in millimeters

ORDERING GUIDE

Model

Package Description

Package Option

ADV7322KSTZ¹

64-Lead Low Profile Quad Flat Package [LQFP]

Evaluation Board

ST-64-2

EVAL-ADV7322EB

¹Z = Pb-free part.

©

registered trademarks are the property of their respective owners.

PR05135–0–9/04(PrA)

Rev. PrA | Page 88 of 88


型号：	EVAL-ADV7322EB
厂家：	ADI
描述：	Multiformat 11-Bit HDTV Video Encoder 多格式11位高清电视视频编码器电视编码器
文件：	总88页 (文件大小：970K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

EVAL-ADV7322EB [ADI]

相关型号：

EVAL-ADV7340EBZ

EVAL-ADV7341EBZ

EVAL-ADV7390EBZ

EVAL-ADV7391EBZ

EVAL-ADV7392EBZ

EVAL-ADV7393EBZ

EVAL-ADV739XFEZ

EVAL-ADV7400AEBM

EVAL-ADV7441AFEZ_1

EVAL-ADV7441AFEZ_2

EVAL-ADV7511W-AKZ

EVAL-ADV7513-AKZ