T81L0010A_06 [TMT]
8-bit MCU; 8位MCU型号: | T81L0010A_06 |
厂家: | TAIWAN MEMORY TECHNOLOGY |
描述: | 8-bit MCU |
文件: | 总17页 (文件大小:105K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TE
tmCH
T81L0010A
8-bit MCU
1. Features
2. General Description
ꢀ
ꢀ
ꢀ
ꢀ
Compatible with MCS-51
The T81L0010A is 8-bit microcontroller designed
and developed with low power and high speed
CMOS technology. It contains a 8K bytes OTP
ROM, a 256 × 8 RAM, 15 I/O lines, a watchdog
timer, two 16-bit counter/timers, a seven source,
Embedded 8K Bytes OTP ROM
256 x 8-bit Internal RAM
two-priority level nested interrupt structure,
a
15 Programmable I/O Lines for 20-pin
Package
full duplex UART, and an on-chip oscillator and
clock circuits.
In addition, the T81L0010A has two selectable
modes of power reduction-idle mode and
power-down mode. The idle mode freezes the
CPU while allowing the RAM, timers, serial port,
and interrupt system to continue functioning. The
power-down mode saves the RAM contents but
freezes the oscillator, causing all other chip
functions to be inoperative.
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
2 16-bit Timer/Counter & 1 16-bit Timer
2 External Interrupt Input
Programmable Serial UART Interface
Low Power Idle & Power-down Modes
Watch-dog Timer
3. Order Information
On-chip Crystal & RC Oscillator (Selected
by Bonding Option)
Part number
Oscillator type
RC
Package
T81L0010A-AK
T81L0010A-BK
T81L0010A-AD
T81L0010A-BD
20-pin DIP
20-pin DIP
20-pin SOP
20-pin SOP
Crystal
RC
Crystal
ꢀ
Internal Power-on Reset and External Reset
Supported
ꢀ
ꢀ
SOP20/DIP20 Package
3.3V Operating Voltage
TM Technology Inc. reserves the right
to change products or specifications without notice.
P. 1
Publication Date: JAN. 2006
Revision:B
TE
tmCH
T81L0010A
4. Block Diagram
RAM Addr.
Register
OTP
ROM
RAM
B
Stack
ACC
Pointer
Register
Program
Address
Register
TMP2
TMP1
Buffer
WDT
ALU
PC
Incrementer
Interrupt, Serial port,
and Timer Block
Program
Counter
PSW
RST
Timing &
Control
Instruction
Register
DPTR
Port 3
Latch
Port 1
Latch
OSC
Port 3
Port 1 Drivers
P1.0 -P1.7
Drivers
XTAL1 XTAL2
P3.0 -P3.5, P3.7
TM Technology Inc. reserves the right
to change products or specifications without notice.
P. 2
Publication Date: JAN. 2006
Revision:B
TE
tmCH
T81L0010A
5. Pin Configuration
RST/VPP
(RXD) P3.0
(TXD) P3.1
XOUT
1
2
20
19
18
17
16
15
14
13
12
11
VCC
P1.7
P1.6
P1.5
3
4
XIN
5
P1.4
P1.3
P1.2
6
(INT0) P3.2
(INT1) P3.3
(T0) P3.4
(T1) P3.5
GND
7
P1.1
8
9
P1.0
P3.7
10
DIP-20/SOP-20 For Crystal Oscillator
T81L0010A-BK/ T81L0010A-BD
RST/VPP
(RXD) P3.0
(TXD) P3.1
OSCR
1
2
20
19
18
17
16
15
14
13
12
11
VCC
P1.7
P1.6
P1.5
3
4
STOP
5
P1.4
P1.3
P1.2
6
(INT0) P3.2
(INT1) P3.3
(T0) P3.4
(T1) P3.5
GND
7
P1.1
8
9
P1.0
P3.7
10
DIP-20/SOP-20 For RC Oscillator
T81L0010A-AK/ T81L0010A-AD
TM Technology Inc. reserves the right
to change products or specifications without notice.
P. 3
Publication Date: JAN. 2006
Revision:B
TE
tmCH
T81L0010A
6. Pin Description
Number
Name
Type
Description
(20-Pin)
Reset signal input or programming supply voltage input.
General-purpose I/O pin (Default) or Serial input port.
General-purpose I/O pin (Default) or Serial output port.
Crystal oscillator output terminal.
RC oscillator external resister connect pin.
Crystal oscillator input terminal.
1
RST/VPP
P3.0/(RXD)
P3.1/(TXD)
XOUT
OSCR
XIN
I
2
I/O
I/O
O
3
4(BK,BD)
4(AK,AD)
I
5(BK,BD)
I
Stop RC oscillator network.
5(AK,AD)
STOP
O
General-purpose I/O pin (Default) or External interrupt source 0.
General-purpose I/O pin (Default) or External interrupt source 1.
General-purpose I/O pin (Default) or Timer 0 external input pin.
General-purpose I/O pin (Default) or Timer 1 external input pin.
Ground
6
P3.2/(INT0)
P3.3/(INT1)
P3.4/(T0)
P3.5/(T1)
GND
I/O
I/O
I/O
I/O
7
8
9
10
11
12
13
14
15
16
17
18
19
20
General-purpose I/O pin
P3.7
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
General-purpose I/O pin
P1.0
General-purpose I/O pin
P1.1
General-purpose I/O pin
P1.2
General-purpose I/O pin
P1.3
General-purpose I/O pin
P1.4
General-purpose I/O pin
P1.5
General-purpose I/O pin
P1.6
General-purpose I/O pin
P1.7
3.3V power supply.
VCC
TM Technology Inc. reserves the right
to change products or specifications without notice.
P. 4
Publication Date: JAN. 2006
Revision:B
TE
tmCH
T81L0010A
7. Temperature Limit Ratings
Parameter
Rating
Units
Operating temperature Range
Storage Temperature Range
-40 to +85
-55 to +125
°C
°C
8. Electrical Characteristics
D.C Characteristics
Symbol
Parameter
Conditions
25°C
Min
3.0
Typ
3.3
-
-
0.1
Max
3.6
1.6
6
Units
V
mA
mA
uA
VCC
Operating Voltage
No load, Vcc=2.5V, 4MHz
No load, Vcc=3.3V, 12MHz
Vcc=3.3V
-
-
-
ICC
IPD
VIH
Operating Current
Power Down Current
Hi-Level input voltage
1
Vout >=VVOH(MIN.)
out <=VVOL(MIN.)
Vout >=VVOH(MIN.)
out <=VVOL(MIN.)
2.1
-
-
-
-
V
V
V
VIL
Low-Level input voltage
Hi-Level Output voltage
0.6
V
IOH=-7uA
2.9
2.4
1.9
VCC=MIN.
VI=VIH or
VIL
VOH
-
-
-
V
V
IOH=-45uA
I
OH=-70uA
IOL=12mA
IOL=25mA
IOL=40mA
0.2
0.4
0.6
VCC=MIN.
VOL
Low-Level Output voltage VI=VIH or
VIL
-
A.C Characteristics
Symbol
Parameter
Conditions
Min
Typ
Max
Units
System Clock 1
(Crystal OSC)
System Clock 2
FSYS1
VCC=3.3V
VCC=3.3V
-
12
24
-
MHz
FSYS2
tRES
-
12
MHz
(RC OSC)
External Reset High Pulse Width
Power ON Start up Time
-
-
10
20
-
-
system cycle
ms
TM Technology Inc. reserves the right
to change products or specifications without notice.
P. 5
Publication Date: JAN. 2006
Revision:B
TE
tmCH
T81L0010A
9. Function Description
9.1. Special Function Register
F8H
F0H
E8H
E0H
D8H
D0H
B
ACC
PSW
C8H T2CON T2MOD
C0H
TL2
TH0
TH2
TH1
B8H
B0H
A8H
A0H
98H
90H
88H
80H
IP
P3
IE
P2
SCON SBUF
P1
TCON TMOD
TL0
DPL
TL1
DPH
P0*
SP
PCON
*Note: P0:Internal still keeping, but for pad dominate, no external pin assignment
Accumulator : ACC
ACC is the Accumulator register. The mnemonics for Accumulator-Specific instructions, however, refer to the
Accumulator simply as A.
B Register : B
The B register is used during multiply and divide operations. For other instructions it can be treated as another scratch
pad register.
Program Status Word : PSW
The PSW register contains program status information as detailed in
CY
AC
F0
RS1
RS0
OV
--
P
BIT SYMBOL FUNCTION
PSW.7 CY Carry flag.
PSW.6 AC Auxiliary Carry flag. (For BCD operations.)
PSW.5 F0 Flag 0. (Available to the user for general purposes.)
PSW.4 RS1 Register bank select control bit 1.
Set/cleared by software to determine working register bank. (See Note.)
PSW.3 RS0 Register bank select control bit 0.
Set/cleared by software to determine working register bank. (See Note.)
PSW.2 OV Overflow flag.
PSW.1
PSW.0
—
P
User-definable flag.
Parity flag.
Set/cleared by hardware each instruction cycle to indicate an odd/even number of “one” bits in the
Accumulator, i.e., even parity.
NOTE: The contents of (RS1, RS0) enable the working register banks as follows:
(0,0)— Bank 0 (00H–07H)
(0,1)— Bank 1 (08H–0fH)
(1,0)— Bank 2 (10H–17H)
(1,1)— Bank 3 (18H–17H)
TM Technology Inc. reserves the right
to change products or specifications without notice.
P. 6
Publication Date: JAN. 2006
Revision:B
TE
tmCH
T81L0010A
Stack Pointer : SP
The Stack Pointer register is 8 bits wide. It is incremented before data is stored during PUSH and CALL executions.
While the stack may reside anywhere in on-chip RAM, the Stack Pointer is initialized to 07H after a reset. This causes the
stack to begin at locations 08H.
Data Pointer (DPTR) : DPH & DPL
The Data Pointer (DPTR) consists of a high byte (DPH) and a low byte (DPL). Its intended function is to hold a 16-bit
address. It may be manipulated as a 16-bit register or as two independent 8-bit registers.
Ports 1.0~1.7 & 3.0~3.5 & 3.7
All Ports are the SFR latches, respectively. Writing a one to a bit of a port SFR (P1 or P3) causes the corresponding
port output pin to switch high. Writing a zero causes the port output pin to switch low. When used as an input, the external
state of a port pin will be held in the port SFR (i.e., if the external state of a pin is low, the corresponding port SFR bit will
contain a ‘0’; if it is high, the bit will contain a ‘1’).
Serial Data Buffer : SBUF
The Serial Buffer is actually two separate registers, a transmit buffer and a receive buffer. When data is moved to
SBUF, it goes to the transmit buffer and is held for serial transmission. (Moving a byte to SBUF is what initiates the
transmission.) When data is moved from SBUF, it comes from the receive buffer.
Timer Registers : TH0, TL0, TH1, TL1,TH2,TL2
Register pairs (TH0, TL0) and (TH1, TL1) and (TH2, TL2) are 16-bit Counting registers for Timer/Counters 0 and
Timer1and Timer2, respectively.
.
Control Register : IP, IE, TMOD, TCON, SCON, PCON
Special Function Registers IP, IE, TMOD, TCON, SCON, and PCON contain control and status bits for the interrupt
system, the Timer/Counters, and the serial port. They are described in later sections.
Standard Serial Interface
The serial port is full duplex, meaning it can transmit and receive simultaneously. It is also receive-buffered, meaning it
can commence reception of a second byte before a previously received byte has been read from the register. (However, if the
first byte still hasn’t been read by the time reception of the second byte is complete, one of the bytes will be lost.) The serial
port receive and transmit registers are both accessed at Special Function Register SBUF. Writing to SBUF loads the transmit
register, and reading SBUF accesses a physically separate receive register.
The serial port can operate in 4 modes:
Mode 0: Serial data enters and exits through RxD. TxD outputs the shift clock. 8 bits are transmitted/received (LSB first).
The baud rate is fixed at 1/12 the oscillator frequency.
Mode 1: 10 bits are transmitted (through TxD) or received (through RxD): a start bit (0), 8 data bits (LSB first), and a stop
bit (1). On receive, the stop bit goes into RB8 in Special Function Register SCON. The baud rate is variable.
Mode 2: 11 bits are transmitted (through TxD) or received (through RxD): start bit (0), 8 data bits (LSB first), a
programmable 9th data bit, and a stop bit (1). On Transmit, the 9th data bit (TB8 in SCON) can be assigned the value of 0 or
1. Or, for example, the parity bit (P, in the PSW) could be moved into TB8. On receive, the 9th data bit goes into RB8 in
Special Function Register SCON, while the stop bit is ignored. The baud rate is programmable to either 1/32 or 1/64 the
oscillator frequency.
Mode 3: 11 bits are transmitted (through TxD) or received (through RxD): a start bit (0), 8 data bits (LSB first), a
programmable 9th data bit, and a stop bit (1). In fact, Mode 3 is the same as Mode 2 in all respects except baud rate. The
baud rate in Mode 3 is variable. In all four modes, transmission is initiated by any instruction that uses SBUF as a destination
register. Reception is initiated in Mode 0 by the condition RI = ‘0’ and REN = ‘1’. Reception is initiated in the other modes
by the incoming start bit if REN = ‘1’.
TM Technology Inc. reserves the right
to change products or specifications without notice.
P. 7
Publication Date: JAN. 2006
Revision:B
TE
tmCH
T81L0010A
Multiprocessor Communications
Modes 2 and 3 have a special provision for multiprocessor communications. In these modes, 9 data bits are received.
The 9th one goes into RB8. Then comes a stop bit. The port can be programmed such that when the stop bit is received, the
serial port interrupt will be activated only if RB8 = ‘1’. This feature is enabled by setting bit SM2 in SCON. A way to use
this feature in multiprocessor systems is as follows: When the master processor wants to transmit a block of data to one of
several slaves, it first sends out an address byte which identifies the target slave. An address byte differs from a data byte in
that the 9th bit is ‘1’ in an address byte and ‘0’ in a data byte. With SM2 = ‘1’, no slave will be interrupted by a data byte. An
address byte, however, will interrupt all slaves, so that each slave can examine the received byte and see if it is being
addressed. The addressed slave will clear its SM2 bit and prepare to receive the data bytes that will be coming. The slaves
that weren’t being addressed leave their SM2s set and go on about their business, ignoring the coming data bytes.
SM2 has no effect in Mode 0, in Mode 1 can be used to check the validity of the stop bit. In Mode 1 reception, if
SM2 = ‘1’, the receive interrupt will not active unless a valid stop bit is received.
Serial Port Control Register
The serial port control and status register is the Special Function Register SCON, shown in Figure 11. This register
contains not only the mode selection bits, but also the 9th data bit for transmit and receive (TB8 and RB8), and the serial port
interrupt bits (TI and RI).
Baud Rates
The baud rate in Mode 0 is fixed: Mode 0 Baud Rate = Oscillator Frequency / 12. The baud rate in Mode 2 depends on
the value of bit SMOD in Special Function Register PCON. If SMOD = ‘0’ (which is the value on reset), the baud rate is 1/64
the oscillator frequency. If SMOD = ‘1’, the baud rate is 1/32 the oscillator frequency.
Mode 2 Baud Rate =2 SMOD/64* (Oscillator Frequency)
In the T81L0010A, the baud rates in Modes 1 and 3 are determined by the Timer 1 overflow rate.
Using Timer 1 to Generate Baud Rates
When Timer 1 is used as the baud rate generator, the baud rates in Modes 1 and 3 are determined by the Timer 1 overflow
rate and the value of SMOD as follows:
Mode 1, 3 Baud Rate =2 SMOD/32* (Timer 1 Overflow Rate)
The Timer 1 interrupt should be disabled in this application. The Timer 1 itself can be configured for either “timer” or
“counter” operation, and in any of its 3 running modes. In the most typical applications, it is configured for “timer” operation,
in the auto-reload mode (high nibble of TMOD = 0010B). In that case the baud rate is given by the formula:
Mode 1, 3 Baud Rate =2 SMOD*(Oscillator Frequency)/ 32/12 / [256 _ (TH1)]
One can achieve very low baud rates with Timer 1 by leaving the Timer 1 interrupt enabled, and configuring the Timer to run
as a 16-bit timer (high nibble of TMOD = 0001B), and using the Timer 1 interrupt to do a 16-bit software reload.
MSB
SM0
Where SM0, SM1 specify the serial port mode, as follows:
LSB
RI
SM1
SM2
REN
TB8
RB8
TI
SM0 SM1
Mode
Description
shift register
8-bit UART
9-bit UART
9-bit UART
Baud Rate
f OSC / 12
Variable
UART FOSC /64 or FOSC /32
Variable
0
0
1
1
0
1
0
1
0
1
2
3
Interrupt Enable Register : IE
MSB
LSB
EX0
EA
wdt
ET2
ES
ET1
EX1
ET0
EA IE.7 Disables all interrupts. If EA = 0, no interrupt will be acknowledged. If EA = 1, each interrupt source is
individually enabled or disabled by setting or clearing its enable bit.
wdt IE.6 Watchdog timer refresh flag.
ET2 IE.5 Enable or disable the Timer 2 overflow interrupt.
ES IE.4 Enable or disable the serial port interrupt.
ET1 IE.3 Enable or disable the Timer 1 overflow interrupt.
EX1
ET0 IE.1 Enable or disable the Timer 0 overflow interrupt.
EX0 IE.0 Enable or disable External Interrupt 0.
IE.2 Enable or disable External Interrupt 1.
TM Technology Inc. reserves the right
to change products or specifications without notice.
P. 8
Publication Date: JAN. 2006
Revision:B
TE
tmCH
T81L0010A
9.2. External Register Table ( for LVR, High/ Normal Driving)
Register Address
Name
Comments
A15…A5-A0
100… 0010 1011
100… 0011 0000
100… 0011 0010
Hex
802bH
8030H
8032H
PWMC2 LVR (Low Voltage Reset)*
Port3 HDS Port3 I/O high driving set**
Port1 HDS Port1 I/O high driving set**
Note :
* LVR (Low Voltage Reset) address : 802bH, read/write
MSB
LSB
Bit 7
Bit 6
Bit5
Bit 4
Bit 3
Bit 2
Bit1
Bit 0
LVR[7]
Reserved
LVR[7] : if LVR[7] write ‘1’, low voltage reset function enable(under 2.1V reset).
default is ‘0’, low voltage reset function disable.
** Port I/O high driving set
if write ‘0’ = set I/O to high driving current mode.
if write ‘1’ = set I/O to normal driving current mode.
default is set ‘1’.
Port 3 high driving address : 8030H
MSB
Bit 7
LSB
Bit 0
Bit 6
Bit5
Bit 4
Bit 3
Bit 2
Bit1
Port3.7
Port3.5
Port3.4
Port3.3
Port3.2
Port3.1
Port3.0
Port 1 high driving address : 8032H
MSB
Bit 7
LSB
Bit 0
Bit 6
Bit5
Bit 4
Bit 3
Bit 2
Bit1
Port1.7
Port1.6
Port1.5
Port1.4
Port1.3
Port1.2
Port1.1
Port1.0
9.3. I/O Ports
Port1
Port 1 is an 8-bit bi-directional I/O port with internal pull-ups. Port 1 output buffers can sink/source four external TTL
device inputs. When port 1 pins are written as 1’s, these pins are pulled high by the internal pull-ups and can be used as
inputs. As inputs, Port 1 pins that are externally being pulled low will source current because of the internal pull-ups.
Port 3
Port 3 is an 8-bit bi-directional I/O port with internal pull-ups. Port 3 output buffers can sink/source four external TTL
device inputs. When port 3 pins are written as 1’s, these pins are pulled high by the internal pull-ups and can be used as
inputs. As inputs, Port 3 pins that are externally being pulled low will source current because of the internal pull-ups.
Port 3 also serves the functions of various special features, as listed below:
P3.0 RXD (serial input port)
P3.1 TXD (serial output port)
P3.2 INT0 (external interrupt 0)
P3.3 INT1 (external interrupt 1)
P3.4 T0 (timer 0 external input)
P3.5 T1 (timer 1 external input)
P3.7 General purpose I/O only
TM Technology Inc. reserves the right
to change products or specifications without notice.
P. 9
Publication Date: JAN. 2006
Revision:B
TE
tmCH
T81L0010A
Watchdog Timer
The watchdog timer is a 16-bit counter that is incremented once every 24 or 384 clock cycles. After an external reset the
watchdog timer is disabled and all registers are set to zeros.
Watchdog Timer structure
The watchdog consists of 16-bit counter wdt, reload register wdtrel, prescalers by 2 and by 16 and control logic.
/2
fclk/12
/16
0
8
14
7
w dts
w dtl
w dth
sw d
w dt
sw dt
control
logic
0
7
6
w dtrel
Watchdog block diagram
Start procedure
There are two ways to start the watchdog. One method, called hardware automatic start, is based on examining the level of
signal swd during active internal rst signal. When this condition is met, the watchdog will start running automatically with
default settings (all registers set to zeros).When this criterion is not met during active internal rst signal, a programmer can
start the watchdog later. It will occur when signal swd becomes active. Once the watchdog is started it cannot be stopped
unless internal rst signal becomes active. When wdt registers enters the state 7CFFh , asynchronous wdts signal will become
active. The signal wdts sets the bit 6 in ip0 register and requests reset state. The wdts is cleared either by rst signal or change
of the state of the wdt timer.
Refreshing the watchdog timer
The watchdog timer must be refreshed regularly to prevent reset request signal from becoming active. This requirement
imposes obligation on the programmer to issue two followed instructions. The first instruction sets wdt and the second one
swdt. The maximum allowed delay between settings of the wdt and swdt is 12 clock cycles. While this period has expired
and swdt has not been set, wdt is automatically reset, otherwise the watchdog timer is reloaded with the content of the wdtrel
register and wdt is automatically reset.
TM Technology Inc. reserves the right
to change products or specifications without notice.
P. 10
Publication Date: JAN. 2006
Revision:B
TE
tmCH
T81L0010A
Special Function Registers
a) Interrupt Enable 0 register (ien0)
The ien0 register (address : A8)
MSB
eal
LSB
ex0
wdt
et2
es0
et1
ex1
et0
The ien0 bit functions
Bit
Symbol
Function
Watchdog timer refresh flag.
Set to initiate a refresh of the watchdog timer. Must be set directly before swdt is set to
prevent an unintentional refresh of the watchdog timer. The wdt is reset by hardware 12
instruction cycles after it has been set.
ien0.6
wdt
Note: other bits are not used to watchdog control
The ien0 bit functions
b) Interrupt Enable 1 register (ien1)
The ien1 register (Address : B8)
MSB
LSB
px0
-
swdt
pt2
ps
pt1
px1
pt0
The ien1 bit functions
Bit
Symbol Function
Watchdog timer start refresh flag.
Set to active/refresh the watchdog timer. When directly set after setting wdt, a watchdog
timer refresh is performed. Bit swdt is reset by hardware 12 instruction cycles after it has
been set.
Ien1.6
swdt
Pay attention that when write ien1.6, it write the swdt bit, when read ien1.6, we will read out the wdts bit. Ie. Watch
dog timer status flag. Set by hardware when the watchdog timer was started.
C) Watchdog Timer Reload register (wdtrel)
The wdtrel register ( Address : 86 )
MSB
7
LSB
0
6
5
4
3
2
1
The wdtrel bit functions
Bit
Symbol Function
Prescaler select bit. When set, the watchdog is clocked through an additional
divide-by-16 prescaler
wdtrel.7
7
Seven bit reload value for the high-byte of the watchdog timer. This value is
loaded to the wdt when a refresh is triggered by a consecutive setting of bits
wdt and swdt
wdtrel.6 t0
wdtrel.0
6-0
The wdtrel register can be loaded and read any time
TM Technology Inc. reserves the right
to change products or specifications without notice.
P. 11
Publication Date: JAN. 2006
Revision:B
TE
tmCH
T81L0010A
WDT Reset
A high on reset pin or watchdog reset request for two clock cycles while the oscillator is running resets the device.
Diagram
wdts
wdts_ff
reset_ff
rst_ff
rst
reset
clk
Reset timing
a) External hardware reset
Figure External reset timing
**Note:
clk: external clock input
Tclk: clock period
reset: external reset input
rst: internally generated reset signal
b) Watchdog timer reset
Figure Watchdog reset timing
**Note:
clk: external clock input
Tclk: clock period
wdt: watchdog timer registers
wdts: watchdog timer status flag
reset: external reset input
rst: internally generated reset signal
TM Technology Inc. reserves the right
to change products or specifications without notice.
P. 12
Publication Date: JAN. 2006
Revision:B
TE
tmCH
T81L0010A
10.Timing Diagram
tLHLL
tPLPH
ALE
PSEN
tAVLL
t
LLPL
LLIV
t
tPLIV
tLLAX
PORT0
PORT2
A0-A7
AVIV
IN STR IN
A 0-A 7
t
A8-A15
A8-A15
ExternalProgram M emoryReadCycle
t
W HLH
t
LHLL
ALE
PSEN
tAVLL
t
LLDV
t
RLDV
t
RLRH
RD
tLLWL
t
AVDV
PORT0
PORT2
A0-A7from RIorDPL
DataIN
A 0-A 7
A8-A15from DPH
A8-A15
ExternalDataM emoryReadCycle
TM Technology Inc. reserves the right
to change products or specifications without notice.
P. 13
Publication Date: JAN. 2006
Revision:B
TE
tmCH
T81L0010A
tW HLH
tLHLL
ALE
tAVLL
tLLW L
tW LW H
PSEN
tLLAX
W R
tAVW L
PORT0
PORT2
A0-A7
A0-A7from RIorDPL
DataOUT
A8-A15from DPH
A8-A15
ExternalDataM emoryW riteCycle
S1........S.1S.6.......S.1S.6.......S.1S.6.......S.1S.6.......S.1S.6.......S.1S.6.......S.1S.6.......S.1S.6.......S.1S.6........S6
ALE
Write to SBUF
Send
Shift
RXD
D0
D1
D2
D3
D4
D5
D6
D7
TXD
Write to SCON, Clear RI
RI
Receive
Shift
RXD
D0
D1
D2
D3
D4
D5
D6
D7
TXD
Serial Port Mode 0
TM Technology Inc. reserves the right
to change products or specifications without notice.
P. 14
Publication Date: JAN. 2006
Revision:B
TE
tmCH
T81L0010A
TX
Write to SBUF
Send
Data
Shift
TXD
Start BitD0
Start BitD0
D1
D1
D2
D2
D3
D3
D4
D4
D5
D5
D6
D6
D7
D7
Stop Bit
TI
RX
RXD
Shift
RI
Stop Bit
Serial Port Mode 1
TX
Write to SBUF
Send
Data
Shift
TXD
Stop Bit
TB8
Start Bit D0
D1
D1
D2
D2
D3
D3
D4
D4
D5
D5
D6
D6
D7
D7
TI
RX
Stop Bit
TB8
Start Bit D0
RXD
Shift
RI
Serial Port Mode 2
TM Technology Inc. reserves the right
to change products or specifications without notice.
P. 15
Publication Date: JAN. 2006
Revision:B
TE
tmCH
T81L0010A
Package Dimension
20-LEAD SOP
0.01 6typ
0.05 0typ
D
X
L
0 .0 0 4 m a x
SYMBOLS
MIN.
0.093
0.004
0.496
0.291
0.394
0.016
0
MAX.
0.104
0.012
0.508
0.229
0.419
0.050
8
A
A1
D
E
H
L
X
UNIT: INCH
TM Technology Inc. reserves the right
to change products or specifications without notice.
P. 16
Publication Date: JAN. 2006
Revision:B
TE
tmCH
T81L0010A
Package Dimension
20-LEAD DIP
D
C
S
e1
B
B1
SYMBOLS
MIN.
-
NOM
-
MAX.
0.175
-
A
A1
A2
B
B1
C
0.015
0.125
0.016
0.058
0.008
1.012
0.290
0.245
0.090
0.120
0.335
-
-
0.130
0.018
0.060
0.010
1.026
0.300
0.250
0.100
0.130
0.355
-
0.135
0.020
0.064
0.011
1.040
0.310
0.225
0.110
0.140
0.375
0.075
D
E
E1
e1
L
eA
S
UNIT: INCH
TM Technology Inc. reserves the right
to change products or specifications without notice.
P. 17
Publication Date: JAN. 2006
Revision:B
相关型号:
©2020 ICPDF网 联系我们和版权申明