2SD2212T100C [ROHM]
Small Signal Bipolar Transistor, 2A I(C), 70V V(BR)CEO, 1-Element, NPN, Silicon,;型号: | 2SD2212T100C |
厂家: | ROHM |
描述: | Small Signal Bipolar Transistor, 2A I(C), 70V V(BR)CEO, 1-Element, NPN, Silicon, 晶体 驱动器 继电器 晶体管 电机 |
文件: | 总3页 (文件大小:107K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Medium Power Transistor
(Motor, Relay drive) (6010V, 2A)
2SD2143
Features
Dimensions (Unit : mm)
1) Built-in zener diode between collector and base.
2) Strong protection against reverse surges due to "L"
loads.
1.5
5.5
3) Built-in resistor between base and emitter.
4) Built-in damper diode.
0.9
C0.5
Absolute maximum ratings (Ta=25C)
Parameter
Collector-base voltage
Collector-emitter voltage
Emitter-base voltage
Symbol
Limits
60 10
60 10
6
Unit
0.8Min.
1.5
VCBO
VCEO
VEBO
V
V
V
2.5
9.5
(1) Base(Gate)
(2) Collector(Drain)
(3) Emitter(Source)
2
A (DC)
A (Pulse)
W
Collector current
IC
ROHM : CPT3
EIAJ : SC-63
∗1
3
1
Collector power dissipation
PC
10
150
W (Tc=25°C)
Junction temperature
Storage temperature
Tj
°C
°C
Tstg
−55 to +150
∗
1 Single pulse Pw=100ms
Packaging specifications and hFE
2SD2143
CPT3
1k to 10k
−
Type
Package
hFE
Marking
Code
TL
Basic ordering unit (pieces)
2500
Inner circuit
C
B
R1
R2
E
E : Emitter
B : Base
C : Collector
R
R
1
2
3.5kΩ
300Ω
Electrical characteristics (Ta=25C)
Symbol
Min.
Typ.
Max.
Unit
Conditions
Parameter
Collector-base breakdown voltage
Collector-emitter breakdown voltage
Collector cutoff current
BVCBO
50
50
−
−
−
1000
−
−
−
−
−
−
−
70
70
1.0
3
V
V
I
I
C
=
=
50μA
5mA
BVCEO
C
I
CBO
EBO
CE(sat)
FE
μA
mA
V
V
V
CB
=40V
Emitter cutoff current
I
EB
=
5V
Collector-emitter saturation voltage
DC current transfer ratio
Transition frequency
V
1.5
I
C/I
B
=
1A/1mA
∗
h
−
80
10000
−
MHz
V
V
V
CE
CE
CB
=
=
=
2V, I
C
=
1A
= −0.1A, f=30MHz
0A, f 1MHz
f
T
−
−
5V, I
E
Output capacitance
Cob
25
pF
10V, I
E
=
=
∗
Measured using pulse current.
www.rohm.com
2012.01 - Rev.C
1/2
c
○ 2012 ROHM Co., Ltd. All rights reserved.
2SD2143
Data Sheet
Electrical characteristics curves
2.0
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
5
Ta=25°C
500μA
500μA
450μA
400μA
350μA
Ta=25°C
V
CE=2V
A
μ
300
450μA
400μA
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
2
1
0.5
0.2
0.1
0.05
0.01
0.2
0
0.2
0
0.001
1
2
3
4
5
2
4
6
8
10
0.5
1
1.5
2
COLLECTOR TO EMITTER VOLTAGE : VCE (V)
COLLECTOR TO EMITTER VOLTAGE : VCE (V)
BASE TO EMITTER VOLTAGE : VBE (V)
Fig.1 Groundede emitter output
Fig.2 Grounded emitter output
Fig.3 Grounded emitter propagation
characteristics
characteristics ( Ι )
characteristics ( ΙΙ )
10000
10000
100
Ta=25°C
CE=4V
V
CE=2V
Ta=25°C
5000
5000
50
V
2000
1000
2000
1000
20
10
500
500
V
CE=2V
5
2
200
100
200
100
IC/IB=1000
1
50
50
0.5
20
10
20
10
0.2
0.001
0.01
0.1 0.2 0.5
1
2
5 10
0.001
0.01
0.1 0.2 0.5
1
2
5 10
0.01
0.1 0.2 0.5
1
2
5 10
COLLECTOR CURRENT : I
C
(A)
COLLECTOR CURRENT : IC (A)
COLLECTOR CURRENT : I
C
(A)
Fig.4 DC current gain
vs. collector current ( Ι )
Fig.5 DC current gain
Fig.6 Collector-emitter saturation
voltage vs. collector current
vs. collector current ( ΙΙ )
10
5
200
100
100
50
I
C/I
B=1000
Ta=25°C
IE=0A
Ic max (pulse)
DC
f=1MHz
2
1
20
10
500m
50
200m
100m
50m
5
20
10
2
1
Ta=−25°
25°C
C
20m
10m
100°C
Ta=25°C
Single
Nonrepetitive
Pulse
5m
0.5
0.2
2m
1m
5
0.01
0.10.2 0.5
1
2
5
10
0.05 0.1 0.2 0.5
1
2
5
10 20 50
0.1 0.2 0.5
1
2
5 10 20 50 100 200 5001000
COLLECTOR CURRENT : I
C
(A)
COLLECTOR TO BASE VOLTAGE : VCB (V)
COLLECTOR TO EMITTER VOLTAGE : VCE (V)
Fig.7 Collector-emitter saturation
voltage vs. collector current
Fig.8 Collector output capacitance
vs. collector-base voltage
Fig.9 Safe operating area (A. S. O)
2SD2143 (CPT)
www.rohm.com
2012.01 - Rev.C
2/2
c
○ 2012 ROHM Co., Ltd. All rights reserved.
Notice
N o t e s
No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specifications,
which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.
The Products specified in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, office-automation equipment, commu-
nication devices, electronic appliances and amusement devices).
The Products specified in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, fire or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-
controller or other safety device). ROHM shall bear no responsibility in any way for use of any
of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
R1120A
相关型号:
2SD2212T101
Power Bipolar Transistor, 2A I(C), 50V V(BR)CEO, 1-Element, NPN, Silicon, Plastic/Epoxy, 3 Pin,
ROHM
2SD2215
Silicon NPN triple diffusion planar type(Silicon NPN triple diffusion planar type)
PANASONIC
2SD2215A
Silicon NPN triple diffusion planar type(Silicon NPN triple diffusion planar type)
PANASONIC
©2020 ICPDF网 联系我们和版权申明