MC-4532DA726EFB-A80 [NEC]
32 M-WORD BY 72-BIT SYNCHRONOUS DYNAMIC RAM MODULE REGISTERED TYPE; 32 m字72 - BIT同步动态RAM模块登记注册类型型号: | MC-4532DA726EFB-A80 |
厂家: | NEC |
描述: | 32 M-WORD BY 72-BIT SYNCHRONOUS DYNAMIC RAM MODULE REGISTERED TYPE |
文件: | 总16页 (文件大小:248K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
DATA SHEET
MOS INTEGRATED CIRCUIT
MC-4532DA726
32 M-WORD BY 72-BIT SYNCHRONOUS DYNAMIC RAM MODULE
REGISTERED TYPE
Description
The MC-4532DA726 is a 33,554,432 words by 72 bits synchronous dynamic RAM module on which 18 pieces of
128M SDRAM: µPD45128441 are assembled.
These modules provide high density and large quantities of memory in a small space without utilizing the surface-
mounting technology on the printed circuit board.
Decoupling capacitors are mounted on power supply line for noise reduction.
Features
• 33,554,432 words by 72 bits organization (ECC type)
• Clock frequency and access time from CLK
Part number
/CAS latency
Clock frequency
(MAX.)
Access time from CLK
(MAX.)
Module type
MC-4532DA726EFB-A80
MC-4532DA726EFB-A10
MC-4532DA726PFB-A80
MC-4532DA726PFB-A10
CL = 3
CL = 2
CL = 3
CL = 2
CL = 3
CL = 2
CL = 3
CL = 2
125 MHz
100 MHz
100 MHz
77 MHz
6 ns
6 ns
6 ns
7 ns
6 ns
6 ns
6 ns
7 ns
PC100 Registered DIMM
Rev. 1.2 Compliant
125 MHz
100 MHz
100 MHz
77 MHz
★
★
• Fully Synchronous Dynamic RAM, with all signals referenced to a positive clock edge
• Pulsed interface
• Possible to assert random column address in every cycle
• Quad internal banks controlled by BA0 and BA1 (Bank Select)
• Programmable burst-length (1, 2, 4, 8 and Full Page)
• Programmable wrap sequence (Sequential / Interleave)
• Programmable /CAS latency (2, 3)
• Automatic precharge and controlled precharge
• CBR (Auto) refresh and self refresh
• All DQs have 10 Ω ± 10 % of series resistor
• Single 3.3 V ± 0.3 V power supply
• LVTTL compatible
• 4,096 refresh cycles / 64 ms
• Burst termination by Burst Stop command and Precharge command
• 168-pin dual in-line memory module (Pin pitch = 1.27 mm)
• Registered type
• Serial PD
The information in this document is subject to change without notice. Before using this document, please
confirm that this is the latest version.
Not all devices/types available in every country. Please check with local NEC representative for
availability and additional information.
Document No. M13633EJ7V0DS00 (7th edition)
Date Published February 2000 NS CP(K)
Printed in Japan
The mark ★ shows major revised points.
1998
©
MC-4532DA726
Ordering Information
Part number
Clock frequency
(MAX.)
Package
Mounted devices
MC-4532DA726EFB-A80
MC-4532DA726EFB-A10
MC-4532DA726PFB-A80
MC-4532DA726PFB-A10
125 MHz
100 MHz
125 MHz
100 MHz
168-pin Dual In-line Memory Module 18 pieces of µPD45128441G5 (Rev. E)
(Socket Type)
(10.16 mm (400) TSOP (II))
Edge connector: Gold plated
43.18 mm height
18 pieces of µPD45128441G5 (Rev. P)
(10.16 mm (400) TSOP (II))
★
★
Data Sheet M13633EJ7V0DS00
2
MC-4532DA726
Pin Configuration
168-pin Dual In-line Memory Module Socket Type (Edge connector: Gold plated)
85
86
87
88
89
90
91
92
93
94
1
2
3
4
5
6
7
8
9
10
V
SS
VSS
/xxx indicates active low signal.
DQ32
DQ33
DQ34
DQ35
Vcc
DQ36
DQ37
DQ38
DQ39
DQ0
DQ1
DQ2
DQ3
Vcc
DQ4
DQ5
DQ6
DQ7
95
96
DQ40
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
DQ8
V
SS
V
SS
97
DQ41
DQ42
DQ43
DQ44
DQ45
Vcc
DQ9
DQ10
DQ11
DQ12
DQ13
Vcc
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
DQ46
DQ47
CB4
DQ14
DQ15
CB0
CB5
CB1
V
SS
V
SS
NC
NC
Vcc
NC
NC
Vcc
/WE
/CAS
DQMB4
DQMB5
NC
DQMB0
DQMB1
/CS0
NC
/RAS
V
SS
V
SS
A0
A2
A1
A3
A4
A5
A6
A7
A8
A9
A0 - A11
: Address Inputs
A10
BA0(A13)
A11
Vcc
BA1(A12)
Vcc
[Row: A0 - A11, Column: A0 - A9, A11]
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
CLK1
NC
Vcc
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
BA0(A13), BA1 (A12) : SDRAM Bank Select
DQ0 - DQ63, CB0 - CB7: Data Inputs/Outputs
CLK0
V
SS
VSS
CKE0
NC
NC
/CS2
DQMB2
DQMB3
NC
DQMB6
DQMB7
NC
CLK0 - CLK3
CKE0
: Clock Input
: Clock Enable Input
: Write Protect
Vcc
Vcc
NC
NC
NC
NC
WP
CB6
CB7
CB2
CB3
/CS0, /CS2
/RAS
: Chip Select Input
: Row Address Strobe
: Column Address Strobe
: Write Enable
V
SS
VSS
DQ48
DQ49
DQ50
DQ51
Vcc
DQ16
DQ17
DQ18
DQ19
Vcc
/CAS
DQ52
NC
DQ20
NC
/WE
NC
NC
REGE
NC
DQMB0 - DQMB7
SA0 - SA2
SDA
: DQ Mask Enable
: Address Input for EEPROM
: Serial Data I/O for PD
: Clock Input for PD
: Power Supply
V
SS
VSS
DQ53
DQ54
DQ55
DQ21
DQ22
DQ23
V
SS
VSS
DQ56
DQ57
DQ58
DQ59
Vcc
DQ24
DQ25
DQ26
DQ27
Vcc
SCL
CC
V
DQ60
DQ61
DQ62
DQ63
DQ28
DQ29
DQ30
DQ31
VSS
CLK2
NC
WP
SS
V
: Ground
V
SS
REGE
NC
: Register / Buffer Enable
: No Connection
CLK3
NC
SA0
SA1
SA2
Vcc
SDA
SCL
Vcc
Data Sheet M13633EJ7V0DS00
3
MC-4532DA726
Block Diagram
/RCS0
RDQMB4
RDQMB0
DQ 3
DQ 2
DQ 1
DQ 0
DQ 0
DQ 1
DQ 2
DQ 3
DQ 0
DQ 1
DQ 2
DQ 3
DQ 32
DQ 33
DQ 34
DQ 35
DQM
D0
DQM
DQM
/CS
/CS
/CS
/CS
D9
DQ 7
DQ 6
DQ 5
DQ 4
DQ 0
DQ 1
DQ 2
DQ 3
DQ 0
DQ 1
DQ 2
DQ 3
DQ 36
DQ 37
DQ 38
DQ 39
DQM
D1
D
10
RDQMB1
RDQMB5
DQ 11
DQ 10
DQ 9
DQ 0
DQ 1
DQ 2
DQ 3
DQ 40
DQ 41
DQ 42
DQ 43
DQ 0
DQ 1
DQ 2
DQ 3
DQM
/CS
/CS
/CS
DQM
/CS
/CS
/CS
D1 - D17
Register1, Register2, PLL
V
CC
D
2
D11
C
D1 - D17
Register1, Register2, PLL
DQ 8
V
SS
DQ 45
DQ 44
DQ 46
DQ 47
DQ 0
DQ 1
DQ 2
DQ 3
DQ 15
DQ 14
DQ 12
DQ 13
DQ 0
DQ 1
DQ 2
DQ 3
DQM
D3
DQM
D12
SERIAL PD
CB 5
CB 4
CB 7
CB 6
DQ 0
DQ 1
DQ 2
DQ 3
DQ 0
DQ 1
DQ 2
DQ 3
DQM
CB 2
CB 3
CB 0
CB 1
DQM
SDA
WP
SCL
D
4
D13
A0
A1
A2
47kΩ
SA0 SA1 SA2
/RCS2
RDQMB2
RDQMB6
DQ 18
DQ 19
DQ 17
DQ 16
DQ 0
DQ 1
DQ 2
DQ 3
DQ 0
DQ 48
DQ 49
DQ 50
DQ 51
DQM
DQM
D5
/CS
/CS
/CS
/CS
DQ 1
DQ 2
DQ 3
D14
10 Ω
CLK1 - CLK3
12pF
DQ 23
DQ 22
DQ 21
DQ 20
DQ 0
DQ 1
DQ 2
DQ 3
DQ 52
DQ 53
DQ 54
DQ 55
DQ 0
DQ 1
DQ 2
DQ 3
DQM
D6
DQM
D15
RDQMB3
RDQMB7
DQ 27
DQ 26
DQ 25
DQ 24
DQ 56
DQ 57
DQ 58
DQ 59
DQ 0
DQ 1
DQ 2
DQ 3
DQ 0
DQ 1
DQ 2
DQ 3
DQM
D16
/CS
/CS
DQM
D7
/CS
/CS
10 Ω
CLK : D0, D1, D9
CLK0
CLK : D2, D10, D11
CLK : D3, D4, D12
CLK : D5, D13, D14
CLK : D6, D7, D15
CLK : D8, D16, D17
CLK : Register1, Register2
PLL
★
DQ 31
DQ 30
DQ 29
DQ 28
DQ 60
DQ 61
DQ 62
DQ 63
DQ 0
DQ 1
DQ 2
DQ 3
DQ 0
DQ 1
DQ 2
DQ 3
DQM
D8
DQM
D17
RA7 - RA11,
RBA0, RBA1
A7 - A11,
BA0, BA1
A0 - A6 : D0 - D17
A0 - A6
RA0 - RA6
A7 - A11, BA0, BA1 : D0 - D17
CKE : D0 - D17
/RAS : D0 - D17
/CAS : D0 - D17
/WE : D0 - D17
RCKE0
/RRAS
/RCAS
/RWE
/RAS
/CAS
/WE
CKE0
RDQMB 2, RDQMB 3,
RDQMB 6, RDQMB 7
DQMB2, DQMB3,
DQMB6, DQMB7
Register1
Register2
/CS2
/RCS2
RDQMB0, RDQMB1,
RDQMB4, RDQMB5
DQMB0, DQMB1,
DQMB4, DQMB5
/RCS0
/CS0
LE
REGE
LE
V
CC
10kΩ
Remarks 1.
Ω
.
The value of all resistors of DQs is 10
2.
3.
µ
×
×
D0 - D17: PD45128441 (8M words 4 bits 4 banks)
≤
IL
REGE V : Buffer mode
≥
IH
REGE V : Register mode
Register: HD74ALVC16835
PLL: HD74CDC2509B
4.
Data Sheet M13633EJ7V0DS00
4
MC-4532DA726
Electrical Specifications
• All voltages are referenced to V (GND).
SS
• After power up, wait more than 1 ms and then, execute power on sequence and CBR (Auto) refresh before proper
device operation is achieved.
Absolute Maximum Ratings
Parameter
Voltage on power supply pin relative to GND
Voltage on input pin relative to GND
Short circuit output current
Symbol
VCC
VT
Condition
Rating
–0.5 to +4.6
–0.5 to +4.6
50
Unit
V
V
IO
mA
W
Power dissipation
PD
21
Operating ambient temperature
Storage temperature
TA
0 to 70
°C
°C
Tstg
–55 to +125
Caution
Exposing the device to stress above those listed in Absolute Maximum Ratings could cause
permanent damage. The device is not meant to be operated under conditions outside the limits
described in the operational section of this specification. Exposure to Absolute Maximum Rating
conditions for extended periods may affect device reliability.
Recommended Operating Conditions
Parameter
Symbol
VCC
VIH
Condition
MIN.
3.0
2.0
–0.3
0
TYP.
3.3
MAX.
3.6
Unit
V
Supply voltage
High level input voltage
Low level input voltage
Operating ambient temperature
VCC + 0.3
+0.8
V
VIL
V
TA
70
°C
Capacitance (TA = 25 °C, f = 1 MHz)
Parameter
Input capacitance
Symbol
Test condition
MIN.
4
TYP.
MAX.
10
Unit
pF
CI1
A0 – A11, BA0(A13), BA1 (A12),
/RAS, /CAS, /WE
CI2
CI3
CI4
CI5
CI/O
CLK0
15
7
25
20
10
10
13
CKE0
/CS0, /CS2
4
DQMB0-DQMB7
DQ0 - DQ63, CB0 - CB7
4
Data input/output capacitance
6
pF
Data Sheet M13633EJ7V0DS00
5
MC-4532DA726
DC Characteristics (Recommended Operating Conditions unless otherwise noted)
Parameter
Symbol
ICC1
Test condition
Grade MIN. MAX. Unit Notes
Operating current
Burst length = 1
/CAS latency = 2 -A80
2,100 mA
2,100
1
tRC ≥ tRC (MIN.), IO = 0 mA
-A10
/CAS latency = 3 -A80
-A10
2,100
2,100
Precharge standby current in
power down mode
ICC2P
CKE ≤ VIL (MAX.), tCK = 15 ns
268
98
mA
mA
★
ICC2PS CKE ≤ VIL (MAX.), tCK = ∞
ICC2N
Precharge standby current in
non power down mode
CKE ≥ VIH (MIN.), tCK = 15 ns, /CS ≥ VIH (MIN.),
610
Input signals are changed one time during 30 ns.
ICC2NS CKE ≥ VIH (MIN.), tCK = ∞ ,
224
Input signals are stable.
Active standby current in
power down mode
ICC3P
CKE ≤ VIL (MAX.), tCK = 15 ns
340
152
790
mA
mA
ICC3PS CKE ≤ VIL (MAX.), tCK = ∞
★
Active standby current in
non power down mode
ICC3N
CKE ≥ VIH (MIN.), tCK = 15 ns, /CS ≥ VIH (MIN.),
Input signals are changed one time during 30 ns.
ICC3NS CKE ≥ VIH (MIN.), tCK = ∞ ,
440
Input signals are stable.
Operating current
(Burst mode)
ICC4
tCK ≥ tCK (MIN.), IO = 0 mA
/CAS latency = 2 -A80
2,190 mA
1,830
2
3
-A10
/CAS latency = 3 -A80
-A10
2,640
2,280
CBR (Auto) Refresh current
ICC5
tRC ≥ tRC (MIN.)
/CAS latency = 2 -A80
-A10
4,440 mA
4,440
★
★
★
★
/CAS latency = 3 -A80
-A10
4,440
4,440
Self refresh current
ICC6
II (L)
CKE ≤ 0.2 V
286
+10
+20
+1.5
mA
Input leakage current
VI = 0 to 3.6 V, All other pins not under test = 0 V
–10
–20
–1.5
2.4
µA
Input leakage current (CKE0)
Output leakage current
High level output voltage
Low level output voltage
IO (L)
VOH
VOL
DOUT is disabled, VO = 0 to 3.6 V
IO = –4.0 mA
µA
V
IO = +4.0 mA
0.4
V
Notes 1. CC1
I
depends on output loading and cycle rates. Specified values are obtained with the output open.
CC1
CK (MIN.)
In addition to this, I
is measured on condition that addresses are changed only one time during t
.
.
2
CC4
. I
depends on output loading and cycle rates. Specified values are obtained with the output open.
CC4
CK (MIN.)
In addition to this, I
is measured on condition that addresses are changed only one time during t
3. CC5
CK (MIN.)
I
is measured on condition that addresses are changed only one time during t
.
Data Sheet M13633EJ7V0DS00
6
MC-4532DA726
AC Characteristics (Recommended Operating Conditions unless otherwise noted)
Test Conditions
★
Parameter
AC high level input voltage / low level input voltage
Input timing measurement reference level
Transition time (Input rise and fall time)
Value
2.4 / 0.4
1.4
Unit
V
V
1
ns
V
Output timing measurement reference level
1.4
t
CK
t
CH
t
CL
2.4 V
CLK
1.4 V
0.4 V
t
SETUP
t
HOLD
2.4 V
1.4 V
0.4 V
Input
t
AC
t
OH
Output
Data Sheet M13633EJ7V0DS00
7
MC-4532DA726
Synchronous Characteristics
Parameter
Symbol
-A80
-A10
Unit
Note
MIN.
8
MAX.
MIN.
10
MAX.
Clock cycle time
/CAS latency = 3
tCK3
tCK2
tAC3
tAC2
(125 MHz)
(100 MHz)
ns
ns
ns
ns
MHz
%
/CAS latency = 2
/CAS latency = 3
/CAS latency = 2
10
(100 MHz)
13
(77 MHz)
Access time from CLK
6
6
6
7
1
1
Input clock frequency
Input CLK duty cycle
Data-out hold time
50
40
3
125
60
50
40
3
100
60
/CAS latency = 3
/CAS latency = 2
tOH3
tOH2
tLZ
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
1
1
3
3
Data-out low-impedance time
Data-out high- impedance time
0
0
/CAS latency = 3
/CAS latency = 2
tHZ3
tHZ2
tDS
3
6
6
3
6
7
3
3
Data-in setup time
Data-in hold time
2
2
tDH
1
1
Address setup time
Address hold time
CKE setup time
tAS
2
2
tAH
1
1
tCKS
tCKH
tCKSP
tCMS
2
2
CKE hold time
1
1
CKE setup time (Power down exit)
2
2
Command (/CS0, /CS2, /RAS, /CAS, /WE, DQMB0 -
DQMB7) setup time
2
2
Command (/CS0, /CS2, /RAS, /CAS, /WE, DQMB0 -
DQMB7) hold time
tCMH
1
1
ns
Note 1. Output load
Z = 50 Ω
Output
50 pF
Remark These specifications are applied to the monolithic device.
Data Sheet M13633EJ7V0DS00
8
MC-4532DA726
Asynchronous Characteristics
Parameter
Symbol
-A80
-A10
Unit
Note
MIN.
MAX.
MIN.
MAX.
ACT to REF/ACT command period (Operation)
REF to REF/ACT command period (Refresh)
ACT to PRE command period
tRC
tRC1
tRAS
tRP
70
70
70
ns
ns
78
48
120,000
50
120,000
ns
PRE to ACT command period
20
20
ns
Delay time ACT to READ/WRITE command
ACT(one) to ACT(another) command period
Data-in to PRE command period
tRCD
tRRD
tDPL
tDAL3
tDAL2
tRSC
tT
20
20
ns
16
20
ns
−1CLK+8
20
−1CLK+10
ns
Data-in to ACT(REF) command
period (Auto precharge)
/CAS latency = 3
/CAS latency = 2
20
20
2
ns
20
ns
Mode register set cycle time
Transition time
2
CLK
ns
0.5
30
64
1
30
64
Refresh time (4,096 refresh cycles)
tREF
ms
Data Sheet M13633EJ7V0DS00
9
MC-4532DA726
Serial PD
(1/2)
Byte No.
0
Function Described
Hex
80H
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Notes
Defines the number of bytes written into
serial PD memory
1
0
0
0
0
0
0
0
128 bytes
1
2
3
4
5
6
7
8
9
Total number of bytes of serial PD memory
Fundamental memory type
Number of rows
08H
04H
0CH
0BH
01H
48H
00H
01H
80H
A0H
60H
60H
02H
80H
04H
04H
01H
8FH
04H
06H
01H
01H
1FH
0EH
A0H
D0H
60H
70H
00H
14H
14H
10H
14H
14H
14H
30H
32H
40H
0
0
0
0
0
0
0
0
1
1
0
0
0
1
0
0
0
1
0
0
0
0
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
1
0
0
0
0
0
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
1
0
1
0
1
1
1
1
1
1
1
1
0
1
0
1
1
0
1
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
1
1
0
1
1
1
0
0
1
1
0
0
0
0
0
1
1
0
1
1
1
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
1
0
0
0
0
1
0
1
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
1
1
0
0
1
0
0
0
0
0
0
0
0
1
1
0
0
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
256 bytes
SDRAM
12 rows
11 columns
1 bank
72 bits
0
Number of columns
Number of banks
Data width
Data width (continued)
Voltage interface
LVTTL
8 ns
CL = 3 Cycle time
-A80
-A10
-A80
-A10
10 ns
6 ns
10
CL = 3 Access time
6 ns
11
12
13
14
15
16
17
18
19
20
21
22
23
DIMM configuration type
Refresh rate/type
ECC
Normal
x4
SDRAM width
Error checking SDRAM width
Minimum clock delay
x4
1 clock
1, 2, 4, 8, F
4 banks
2, 3
Burst length supported
Number of banks on each SDRAM
/CAS latency supported
/CS latency supported
/WE latency supported
SDRAM module attributes
0
0
Registered
SDRAM device attributes : General
CL = 2 Cycle time
CL = 2 Access time
-A80
10 ns
13 ns
6 ns
-A10
-A80
-A10
24
7 ns
25-26
27
tRP(MIN.)
-A80
-A10
-A80
-A10
-A80
-A10
-A80
-A10
20 ns
20 ns
28
29
30
31
tRRD(MIN.)
16 ns
20 ns
tRCD(MIN.)
20 ns
20 ns
tRAS(MIN.)
48 ns
50 ns
Module bank density
256M bytes
Data Sheet M13633EJ7V0DS00
10
MC-4532DA726
(2/2)
Byte No.
32
Function Described
Hex
20H
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Notes
Command and address signal input
0
0
1
0
0
0
0
0
2 ns
1 ns
setup time
33
Command and address signal input hold
time
10H
0
0
0
1
0
0
0
0
34
35
Data signal input setup time
Data signal input hold time
20H
10H
00H
12H
3AH
A0H
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
1
1
0
1
0
1
1
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
1
1
0
0
0
0
0
0
0
2 ns
1 ns
36-61
62
SPD revision
1.2 A
63
Checksum for bytes 0 - 62
-A80
-A10
64-71 Manufacture’s JEDEC ID code
72 Manufacturing location
73-90 Manufacture’s P/N
91 Revision Code
93-94 Manufacturing date
95-98 Assembly serial number
99-125 Mfg specific
126
127
Intel specification frequency
Intel specification /CAS
latency support
64H
87H
85H
0
1
1
1
0
0
1
0
0
0
0
0
0
0
0
1
1
1
0
1
0
0
1
1
100 MHz
-A80
-A10
Timing Chart
Refer to the SYNCHRONOUS DRAM MODULE TIMING CHART Information (M13348E).
Data Sheet M13633EJ7V0DS00
11
MC-4532DA726
Package Drawing
168-PIN DUAL IN-LINE MODULE (SOCKET TYPE)
A (AREA B)
Y
Z
N
M1 (AREA B)
R
Q
L
M
A
B
S
M2 (AREA A)
J
T
H
(OPTIONAL HOLES)
U
K
C
E
B
I
G
D
A1 (AREA A)
ITEM MILLIMETERS
A
A1
B
133.35
133.35±0.13
11.43
C
36.83
D
6.35
D1
D2
E
2.0
detail of A part
W
detail of B part
D2
3.125
54.61
G
H
6.35
1.27 (T.P.)
8.89
I
J
24.495
42.18
K
L
17.78
M
M1
M2
N
43.18±0.13
23.40
V
P
19.78
X
D1
4.0 MAX.
1.0
P
Q
R
R2.0
4.0±0.10
φ
S
3.0
T
1.27±0.1
4.0 MIN.
U
V
0.2±0.15
1.0±0.05
2.54±0.10
3.0 MIN.
W
X
Y
Z
3.0 MIN.
M168S-50A107
Data Sheet M13633EJ7V0DS00
12
MC-4532DA726
[MEMO]
Data Sheet M13633EJ7V0DS00
13
MC-4532DA726
[MEMO]
Data Sheet M13633EJ7V0DS00
14
MC-4532DA726
NOTES FOR CMOS DEVICES
1
PRECAUTION AGAINST ESD FOR SEMICONDUCTORS
Note:
Strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and
ultimately degrade the device operation. Steps must be taken to stop generation of static electricity
as much as possible, and quickly dissipate it once, when it has occurred. Environmental control
must be adequate. When it is dry, humidifier should be used. It is recommended to avoid using
insulators that easily build static electricity. Semiconductor devices must be stored and transported
in an anti-static container, static shielding bag or conductive material. All test and measurement
tools including work bench and floor should be grounded. The operator should be grounded using
wrist strap. Semiconductor devices must not be touched with bare hands. Similar precautions need
to be taken for PW boards with semiconductor devices on it.
2
HANDLING OF UNUSED INPUT PINS FOR CMOS
Note:
No connection for CMOS device inputs can be cause of malfunction. If no connection is provided
to the input pins, it is possible that an internal input level may be generated due to noise, etc., hence
causing malfunction. CMOS devices behave differently than Bipolar or NMOS devices. Input levels
of CMOS devices must be fixed high or low by using a pull-up or pull-down circuitry. Each unused
pin should be connected to VDD or GND with a resistor, if it is considered to have a possibility of
being an output pin. All handling related to the unused pins must be judged device by device and
related specifications governing the devices.
3
STATUS BEFORE INITIALIZATION OF MOS DEVICES
Note:
Power-on does not necessarily define initial status of MOS device. Production process of MOS
does not define the initial operation status of the device. Immediately after the power source is
turned ON, the devices with reset function have not yet been initialized. Hence, power-on does
not guarantee out-pin levels, I/O settings or contents of registers. Device is not initialized until the
reset signal is received. Reset operation must be executed immediately after power-on for devices
having reset function.
Data Sheet M13633EJ7V0DS00
15
MC-4532DA726
CAUTION FOR HANDLING MEMORY MODULES
When handling or inserting memory modules, be sure not to touch any components on the modules, such as
the memory IC, chip capacitors and chip resistors. It is necessary to avoid undue mechanical stress on these
components to prevent damaging them.
When re-packing memory modules, be sure the modules are NOT touching each other. Modules in contact
with other modules may cause excessive mechanical stress, which may damage the modules.
• The information in this document is subject to change without notice. Before using this document, please
confirm that this is the latest version.
• No part of this document may be copied or reproduced in any form or by any means without the prior written
consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in
this document.
• NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property
rights of third parties by or arising from use of a device described herein or any other liability arising from use
of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other
intellectual property rights of NEC Corporation or others.
• Descriptions of circuits, software, and other related information in this document are provided for illustrative
purposes in semiconductor product operation and application examples. The incorporation of these circuits,
software, and information in the design of the customer's equipment shall be done under the full responsibility
of the customer. NEC Corporation assumes no responsibility for any losses incurred by the customer or third
parties arising from the use of these circuits, software, and information.
• While NEC Corporation has been making continuous effort to enhance the reliability of its semiconductor devices,
the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or
property arising from a defect in an NEC semiconductor device, customers must incorporate sufficient safety
measures in its design, such as redundancy, fire-containment, and anti-failure features.
• NEC devices are classified into the following three quality grades:
"Standard", "Special", and "Specific". The Specific quality grade applies only to devices developed based on a
customer designated "quality assurance program" for a specific application. The recommended applications of
a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device
before using it in a particular application.
Standard: Computers, office equipment, communications equipment, test and measurement equipment,
audio and visual equipment, home electronic appliances, machine tools, personal electronic
equipment and industrial robots
Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster
systems, anti-crime systems, safety equipment and medical equipment (not specifically designed
for life support)
Specific: Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life
support systems or medical equipment for life support, etc.
The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books.
If customers intend to use NEC devices for applications other than those specified for Standard quality grade,
they should contact an NEC sales representative in advance.
M7 98. 8
相关型号:
MC-4532DA727-A75
Synchronous DRAM Module, 32MX72, 5.4ns, MOS, 43.18 MM HEIGHT, 1.27 MM PITCH, DIMM-168
ELPIDA
©2020 ICPDF网 联系我们和版权申明