BAT54ALT1 [MOTOROLA]
30 VOLTS SCHOTTKY BARRIER DETECTOR AND SWITCHING DIODES; 30伏肖特基探测器和开关二极管型号: | BAT54ALT1 |
厂家: | MOTOROLA |
描述: | 30 VOLTS SCHOTTKY BARRIER DETECTOR AND SWITCHING DIODES |
文件: | 总4页 (文件大小:82K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Order this document
by BAT54ALT1/D
SEMICONDUCTOR TECHNICAL DATA
These Schottky barrier diodes are designed for high speed switching applications,
circuit protection, and voltage clamping. Extremely low forward voltage reduces
conduction loss. Miniature surface mount package is excellent for hand held and
portable applications where space is limited.
Motorola Preferred Device
•
•
Extremely Fast Switching Speed
Low Forward Voltage — 0.35 Volts (Typ) @ I = 10 mAdc
30 VOLTS
SCHOTTKY BARRIER
DETECTOR AND SWITCHING
DIODES
F
CATHODE
1
ANODE
3
2
CATHODE
3
1
2
CASE 318–08, STYLE 12
SOT–23 (TO–236AB)
MAXIMUM RATINGS (T = 125°C unless otherwise noted)
J
Rating
Reverse Voltage
Symbol
Value
Unit
V
R
30
Volts
Forward Power Dissipation
P
F
@ T = 25°C
225
1.8
mW
mW/°C
A
Derate above 25°C
Forward Current (DC)
Junction Temperature
Storage Temperature Range
DEVICE MARKING
BAT54ALT1 = B6
I
200 Max
125 Max
mA
°C
F
T
J
T
stg
–55 to +150
°C
ELECTRICAL CHARACTERISTICS (T = 25°C unless otherwise noted) (EACH DIODE)
A
Characteristic
Reverse Breakdown Voltage (I = 10 µA)
Symbol
Min
30
—
Typ
—
Max
—
Unit
V
Volts
pF
R
(BR)R
Total Capacitance (V = 1.0 V, f = 1.0 MHz)
C
7.6
0.5
10
R
T
Reverse Leakage (V = 25 V)
I
R
—
2.0
0.24
0.5
1.0
5.0
µAdc
Vdc
Vdc
Vdc
ns
R
Forward Voltage (I = 0.1 mAdc)
V
F
V
F
V
F
—
—
—
—
0.22
0.41
0.52
—
F
Forward Voltage (I = 30 mAdc)
F
Forward Voltage (I = 100 mAdc)
F
Reverse Recovery Time
t
rr
(I = I = 10 mAdc, I
= 1.0 mAdc) Figure 1
F
R
R(REC)
Forward Voltage (I = 1.0 mAdc)
V
V
—
—
—
—
—
0.29
0.35
—
0.32
0.40
200
300
600
Vdc
Vdc
F
F
Forward Voltage (I = 10 mAdc)
F
F
Forward Current (DC)
I
F
mAdc
mAdc
mAdc
Repetitive Peak Forward Current
I
—
FRM
Non–Repetitive Peak Forward Current (t < 1.0 s)
I
—
FSM
Preferred devices are Motorola recommended choices for future use and best overall value.
Thermal Clad is a registered trademark of the Bergquist Company.
REV 3
Motorola, Inc. 1997
820
Ω
+10 V
2 k
0.1 µF
I
F
t
t
t
r
p
I
F
100 µH
t
rr
t
10%
90%
0.1
µF
DUT
50
Ω
OUTPUT
PULSE
GENERATOR
50 Ω INPUT
i
= 1 mA
SAMPLING
OSCILLOSCOPE
R(REC)
I
R
V
R
OUTPUT PULSE
(I = I = 10 mA; measured
INPUT SIGNAL
F
R
at i
= 1 mA)
R(REC)
Notes: 1. A 2.0 kΩ variable resistor adjusted for a Forward Current (I ) of 10 mA.
F
Notes: 2. Input pulse is adjusted so I
is equal to 10 mA.
R(peak)
Notes: 3. t » t
p
rr
Figure 1. Recovery Time Equivalent Test Circuit
100
10
1000
T
= 150°C
A
100
T
= 125
°
C
C
A
150°C
10
1.0
125°C
T = 85
A
°
1.0
0.1
0.01
85°C
25°C
–40
°C
–55
°C
T
= 25°C
A
0.001
0.1
0.0
25
30
0.1
0.2
0.3
0.4
0.5
0.6
0
5
10
15
20
V
, REVERSE VOLTAGE (VOLTS)
R
V , FORWARD VOLTAGE (VOLTS)
F
Figure 2. Forward Voltage
Figure 3. Leakage Current
14
12
10
8
6
4
2
0
0
5
10
15
20
25
30
V
, REVERSE VOLTAGE (VOLTS)
R
Figure 4. Total Capacitance
5–2
Motorola Small–Signal Transistors, FETs and Diodes Device Data
INFORMATION FOR USING THE SOT–23 SURFACE MOUNT PACKAGE
MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS
Surface mount board layout is a critical portion of the total
design. The footprint for the semiconductor packages must
be the correct size to insure proper solder connection
interface between the board and the package. With the
correct pad geometry, the packages will self align when
subjected to a solder reflow process.
0.037
0.95
0.037
0.95
0.079
2.0
0.035
0.9
0.031
0.8
inches
mm
SOT–23
SOT–23 POWER DISSIPATION
The power dissipation of the SOT–23 is a function of the
SOLDERING PRECAUTIONS
drain pad size. This can vary from the minimum pad size for
soldering to a pad size given for maximum power dissipation.
Power dissipation for a surface mount device is determined
The melting temperature of solder is higher than the rated
temperature of the device. When the entire device is heated
to a high temperature, failure to complete soldering within a
short time could result in device failure. Therefore, the
following items should always be observed in order to
minimize the thermal stress to which the devices are
subjected.
by T
, the maximum rated junction temperature of the
, the thermal resistance from the device junction to
J(max)
die, R
θJA
ambient, and the operating temperature, T . Using the
A
values provided on the data sheet for the SOT–23 package,
P
can be calculated as follows:
D
•
•
Always preheat the device.
The delta temperature between the preheat and
soldering should be 100°C or less.*
T
– T
A
J(max)
P
=
D
R
θJA
•
When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering method,
the difference shall be a maximum of 10°C.
The values for the equation are found in the maximum
ratings table on the data sheet. Substituting these values into
the equation for an ambient temperature T of 25°C, one can
A
calculate the power dissipation of the device which in this
case is 225 milliwatts.
•
•
•
The soldering temperature and time shall not exceed
260°C for more than 10 seconds.
When shifting from preheating to soldering, the
maximum temperature gradient shall be 5°C or less.
After soldering has been completed, the device should
be allowed to cool naturally for at least three minutes.
Gradual cooling should be used as the use of forced
cooling will increase the temperature gradient and result
in latent failure due to mechanical stress.
150°C – 25°C
556°C/W
P
=
= 225 milliwatts
D
The 556°C/W for the SOT–23 package assumes the use
of the recommended footprint on a glass epoxy printed circuit
board to achieve a power dissipation of 225 milliwatts. There
are other alternatives to achieving higher power dissipation
from the SOT–23 package. Another alternative would be to
use a ceramic substrate or an aluminum core board such as
Thermal Clad . Using a board material such as Thermal
Clad, an aluminum core board, the power dissipation can be
doubled using the same footprint.
•
Mechanical stress or shock should not be applied during
cooling.
* Soldering a device without preheating can cause excessive
thermal shock and stress which can result in damage to the
device.
Motorola Small–Signal Transistors, FETs and Diodes Device Data
5–3
PACKAGE DIMENSIONS
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
A
L
2. CONTROLLING DIMENSION: INCH.
3. MAXIMUM LEAD THICKNESS INCLUDES LEAD
FINISH THICKNESS. MINIMUM LEAD THICKNESS
IS THE MINIMUM THICKNESS OF BASE
MATERIAL.
3
S
B
1
2
INCHES
MIN MAX
MILLIMETERS
DIM
A
B
C
D
G
H
J
MIN
2.80
1.20
0.89
0.37
1.78
0.013
0.085
0.45
0.89
2.10
0.45
MAX
3.04
1.40
1.11
0.50
2.04
0.100
0.177
0.60
1.02
2.50
0.60
V
G
0.1102 0.1197
0.0472 0.0551
0.0350 0.0440
0.0150 0.0200
0.0701 0.0807
0.0005 0.0040
0.0034 0.0070
0.0180 0.0236
0.0350 0.0401
0.0830 0.0984
0.0177 0.0236
K
L
S
C
V
H
J
D
K
STYLE 12:
PIN 1. CATHODE
2. CATHODE
3. ANODE
CASE 318–08
ISSUE AE
SOT–23 (TO–236AB)
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specificallydisclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
datasheetsand/orspecificationscananddovaryindifferentapplicationsandactualperformancemayvaryovertime. Alloperatingparameters,including“Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applicationsintended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
ordeathmayoccur. ShouldBuyerpurchaseoruseMotorolaproductsforanysuchunintendedorunauthorizedapplication,BuyershallindemnifyandholdMotorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
Opportunity/Affirmative Action Employer.
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Mfax is a trademark of Motorola, Inc.
How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution;
P.O. Box 5405, Denver, Colorado 80217. 303–675–2140 or 1–800–441–2447
JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 4–32–1,
Nishi–Gotanda, Shinagawa–ku, Tokyo 141, Japan. 81–3–5487–8488
Mfax : RMFAX0@email.sps.mot.com – TOUCHTONE 602–244–6609
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
– US & Canada ONLY 1–800–774–1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
INTERNET: http://motorola.com/sps
BAT54ALT1/D
◊
相关型号:
©2020 ICPDF网 联系我们和版权申明