MAX1473EUI-TG05 [MAXIM]
Consumer Circuit, CMOS, PDSO28, TSSOP-28;型号: | MAX1473EUI-TG05 |
厂家: | MAXIM INTEGRATED PRODUCTS |
描述: | Consumer Circuit, CMOS, PDSO28, TSSOP-28 光电二极管 商用集成电路 |
文件: | 总17页 (文件大小:410K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
19-2748; Rev 3; 11/03
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
General Description
Features
o Optimized for 315MHz or 433MHz ISM Band
The MAX1473 fully integrated low-power CMOS super-
heterodyne receiver is ideal for receiving amplitude-
shift-keyed (ASK) data in the 300MHz to 450MHz
frequency range. Its signal range is from -114dBm to
0dBm. With few external components and a low-current
power-down mode, it is ideal for cost- and power-sensi-
tive applications typical in the automotive and consumer
markets. The chip consists of a low-noise amplifier
(LNA), a fully differential image-rejection mixer, an on-
chip phase-locked-loop (PLL) with integrated voltage-
controlled oscillator (VCO), a 10.7MHz IF limiting
amplifier stage with received-signal-strength indicator
(RSSI), and analog baseband data-recovery circuitry.
The MAX1473 also has a discrete one-step automatic
gain control (AGC) that drops the LNA gain by 35dB
when the RF input signal is greater than -57dBm.
o Operates from Single 3.3V or 5.0V Supplies
o High Dynamic Range with On-Chip AGC
o Selectable Image-Rejection Center Frequency
o Selectable x64 or x32 f /f
Ratio
LO XTAL
o Low 5.2mA Operating Supply Current
o <2.5µA Low-Current Power-Down Mode for
Efficient Power Cycling
o 250µs Startup Time
o Built-In 50dB RF Image Rejection
o Receive Sensitivity of -114dBm
The MAX1473 is available in 28-pin TSSOP and 32-pin
thin QFN packages. Both versions are specified for the
extended (-40°C to +85°C) temperature range.
Ordering Information
PART
MAX1473EUI
MAX1473ETJ
TEMP RANGE
-40°C to +85°C
-40°C to +85°C
PIN-PACKAGE
28 TSSOP
Applications
Automotive Remote Keyless Entry Security Systems
32 Thin QFN
Garage Door Openers
Remote Controls
Home Automation
Local Telemetry
Systems
Functional Diagram and Typical Application Circuit appear
at end of data sheet.
Wireless Sensors
Pin Configurations
TOP VIEW
XTAL1
1
2
3
4
5
6
7
8
9
28 XTAL2
AV
DD
27 PWRDN
26 PDOUT
25 DATAOUT
LNAIN
LNASRC
AGND
N.C.
AGND
1
2
3
4
5
6
7
8
24 DATAOUT
23
24
V
DD5
V
DD5
MAX1473
LNAOUT
23 DSP
LNAOUT
22 DSP
21 N.C.
20 DFFB
19 OPP
18 DSN
17 DFO
AV
DD
22 DFFB
21 OPP
AV
DD
MAX1473
MIXIN1
MIXIN2
MIXIN1
MIXIN2
AGND
20 DSN
AGND 10
IRSEL 11
19 DFO
18 IFIN2
17 IFIN1
16 XTALSEL
15 AGCDIS
IRSEL
MIXOUT 12
DGND 13
DV
14
DD
TSSOP
THIN QFN
________________________________________________________________ Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
ABSOLUTE MAXIMUM RATINGS
AV
AV
DV
to AGND ....................................................-0.3V to +6.0V
Continuous Power Dissipation (T = +70°C)
DD5
A
to AGND ......................................................-0.3V to +4.0V
28-Pin TSSOP (derate 12.8mW/°C above +70°C) .1025.6mW
DD
DD
to DGND......................................................-0.3V to +4.0V
32-Pin Thin QFN (derate 21.3mW/°C
AGND to DGND.....................................................-0.1V to +0.1V
IRSEL, DATAOUT, XTALSEL, AGCDIS,
above +70°C).........................................................1702.1mW
Operating Temperature Ranges
PWRDN to AGND .....................................-0.3V to (V
All Other Pins to AGND ..............................-0.3V to (V
+ 0.3V)
+ 0.3V)
MAX1473E__ ..................................................-40°C to +85°C
Storage Temperature Range.............................-60°C to +150°C
Lead Temperature (soldering 10s) ..................................+300°C
DD5
DD
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS (3.3V OPERATION)
(Typical Application Circuit, V
= 3.0V to 3.6V, no RF signal applied, T = -40°C to +85°C, unless otherwise noted. Typical values
DD
A
are at V
= 3.3V and T = +25°C.) (Note 1)
DD
A
PARAMETER
SYMBOL
CONDITIONS
3.3V nominal supply
MIN
TYP
3.3
5.2
5.8
1.6
2.5
MAX
3.6
UNITS
Supply Voltage
V
3.0
V
DD
f
RF
f
RF
f
RF
f
RF
= 315MHz
= 433MHz
= 315MHz
= 433MHz
6.23
6.88
Supply Current
I
V
= V
mA
µA
DD
P WRDN
DD
V
V
= 0V,
= 0V
P WRDN
Shutdown Supply Current
I
PWRDN
XTALSEL
5.3
0.4
Input Voltage Low
V
V
V
IL
IH
IH
Input Voltage High
Input Logic Current High
V
V
V
- 0.4
DD
I
10
µA
f
RF
f
RF
f
RF
= 433MHz, V
= 375MHz, V
= 315MHz, V
= V
V
V
- 0.4
IRSEL
IRSEL
IRSEL
DD
DD
DD
Image Reject Select (Note 2)
= V /2
DD
1.1
0.4
- 1.5
V
= 0V
DATAOUT Voltage Output Low
DATAOUT Voltage Output High
V
0.4
V
V
OL
R = 5kΩ
L
V
- 0.4
DD
OH
2
_______________________________________________________________________________________
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
DC ELECTRICAL CHARACTERISTICS (5.0V OPERATION)
(Typical Application Circuit, V
= 4.5V to 5.5V, no RF signal applied, T = -40°C to +85°C, unless otherwise noted. Typical values
DD
A
are at V
= 5.0V and T = +25°C.) (Note 1)
DD
A
PARAMETER
SYMBOL
CONDITIONS
5.0V nominal supply
MIN
TYP
5.0
5.2
5.7
2.3
2.8
MAX
5.5
UNITS
Supply Voltage
V
4.5
V
DD
f
RF
f
RF
f
RF
f
RF
= 315MHz
= 433MHz
= 315MHz
= 433MHz
6.04
6.76
Supply Current
I
V
= V
mA
µA
DD
P WRDN
DD
V
V
= 0V,
= 0V
P WRDN
Shutdown Supply Current
I
PWRDN
XTALSEL
6.2
0.4
Input Voltage Low
V
V
V
IL
IH
IH
Input Voltage High
Input Logic Current High
V
V
V
- 0.4
DD
I
10
µA
f
RF
f
RF
f
RF
= 433MHz, V
= 375MHz, V
= 315MHz, V
= V
V
V
- 0.4
IRSEL
IRSEL
IRSEL
DD
DD
DD
Image Reject Select (Note 2)
= V /2
DD
1.1
0.4
- 1.5
V
= 0V
DATAOUT Voltage Output Low
DATAOUT Voltage Output High
V
0.4
V
V
OL
R = 5kΩ
L
V
- 0.4
DD
OH
AC ELECTRICAL CHARACTERISTICS
(Typical Application Circuit, V
erwise noted. Typical values are at V
= 3.0V to 3.6V, all RF inputs are referenced to 50Ω, f = 315MHz, T = -40°C to +85°C, unless oth-
DD
RF A
= 3.3V and T = +25°C.) (Note 1).
A
DD
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
GENERAL CHARACTERISTICS
Time for valid signal detection after
Startup Time
t
250
µs
ON
V
= V
OH
P WRDN
Receiver Input Frequency
f
300
450
MHz
dBm
RF
Maximum Receiver Input Level
P
Modulation depth > 18dB
Average carrier power level
Peak power level
0
RFIN_MAX
-120
-114
8
Sensitivity (Note 3)
AGC Hysteresis
P
dBm
RFIN_MIN
dB
ms
LNA gain from low to high
150
LNA IN HIGH-GAIN MODE
Power Gain
16
dB
f
RF
f
RF
f
RF
= 433MHz
= 375MHz
= 315MHz
1 - j4.7
1 - j3.9
1 - j3.4
-22
Normalized to
50Ω (Note 4)
Input Impedance
S11
LNA
1dB Compression Point
P1dB
dBm
dBm
LNA
Input-Referred 3rd-Order
Intercept
IIP3
-12
LNA
_______________________________________________________________________________________
3
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
AC ELECTRICAL CHARACTERISTICS (continued)
(Typical Application Circuit, V
erwise noted. Typical values are at V
= 3.0V to 3.6V, all RF inputs are referenced to 50Ω, f = 315MHz, T = -40°C to +85°C, unless oth-
DD
RF A
= 3.3V and T = +25°C.) (Note 1)
A
DD
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
LO Signal Feedthrough to
Antenna
-80
dBm
Output Impedance
Noise Figure
S22
Normalized to 50Ω
0.12 - j4.4
2
LNA
NF
dB
LNA
LNA IN LOW-GAIN MODE
f
RF
f
RF
f
RF
= 433MHz
= 375MHz
= 315MHz
1 - j4.7
1 - j3.9
1 - j3.4
-10
Normalized to
50Ω
Input Impedance (Note 4)
1dB Compression Point
S11
LNA
P1dB
dBm
dBm
LNA
Input-Referred 3rd-Order
Intercept
IIP3
-7
LNA
LO Signal Feedthrough to
Antenna
-80
dBm
Output Impedance
Noise Figure
S22
Normalized to 50Ω
0.4
2
LNA
LNA
NF
dB
dB
dB
Power Gain
0
Voltage Gain Reduction
MIXER
AGC enabled (depends on tank Q)
35
Input Impedance
S11
IIP3
Normalized to 50Ω
0.25 - j2.4
-18
MIX
MIX
Input-Referred 3rd-Order
Intercept
dBm
Output Impedance
Noise Figure
Z
330
16
42
44
44
13
Ω
OUT_MIX
NF
dB
MIX
f
f
f
= 433MHz, V
= 375MHz, V
= 315MHz, V
= V
DD
RF
RF
RF
IRSEL
IRSEL
IRSEL
Image Rejection
(not Including LNA Tank)
= V /2
DD
dB
dB
= 0V
Conversion Gain
330Ω IF filter load
INTERMEDIATE FREQUENCY (IF)
Input Impedance
Z
330
10.7
20
Ω
IN_IF
Operating Frequency
3dB Bandwidth
f
Bandpass response
MHz
MHz
dB
IF
RSSI Linearity
0.5
RSSI Dynamic Range
80
dB
P
P
< -120dBm
1.15
2.35
14.2
1.45
2.05
RFIN
RFIN
RSSI Level
V
mV/dB
V
> 0dBm, AGC enabled
RSSI Gain
LNA gain from low to high
LNA gain from high to low
AGC Threshold
4
_______________________________________________________________________________________
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
AC ELECTRICAL CHARACTERISTICS (continued)
(Typical Application Circuit, V
erwise noted. Typical values are at V
= 3.0V to 3.6V, all RF inputs are referenced to 50Ω, f = 315MHz, T = -40°C to +85°C, unless oth-
DD
RF A
= 3.3V and T = +25°C.) (Note 1)
A
DD
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
DATA FILTER
Maximum Bandwidth
DATA SLICER
BW
100
kHz
DF
Comparator Bandwidth
Maximum Load Capacitance
Output High Voltage
Output Low Voltage
BW
100
10
kHz
pF
V
CMP
C
LOAD
V
DD5
0
V
CRYSTAL OSCILLATOR
V
V
V
V
= 0V
6.6128
13.2256
4.7547
9.5094
50
XTALSEL
XTALSEL
XTALSEL
XTALSEL
f
f
= 433MHz
= 315MHz
MHz
MHz
RF
= V
DD
Crystal Frequency (Note 5)
f
XTAL
= 0V
= V
RF
DD
Crystal Tolerance
Input Impedance
ppm
pF
From each pin to ground
6.2
Note 1: 100% tested at T = +25°C. Guaranteed by design and characterization over temperature.
A
Note 2: IRSEL is internally set to 375MHz IR mode. It can be left open when the 375MHz image rejection setting is desired. A 1nF
capacitor is recommended in noisy environments.
-3
Note 3: BER = 2 x 10 , Manchester encoded, data rate = 4kbps, IF bandwidth = 280kHz.
Note 4: Input impedance is measured at the LNAIN pin. Note that the impedance includes the 15nH inductive degeneration con-
nected from the LNA source to ground. The equivalent input circuit is 50Ω in series with 2.2pF.
Note 5: Crystal oscillator frequency for other RF carrier frequency within the 300MHz to 450MHz range is (f - 10.7MHz)/64 for
RF
XTALSEL = 0V, and (f - 10.7MHz)/32 for XTALSEL = V
.
RF
DD
_______________________________________________________________________________________
5
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
Typical Operating Characteristics
(Typical Application Circuit, V
= 3.3V, f = 315MHz, T = +25°C, unless otherwise noted.)
RF A
DD
SUPPLY CURRENT
vs. RF FREQUENCY
SUPPLY CURRENT
vs. SUPPLY VOLTAGE
BIT-ERROR RATE
vs. AVERAGE RF INPUT POWER
7.0
6.5
6.0
5.5
5.0
4.5
100
10
5.6
5.5
5.4
5.3
5.2
5.1
5.0
4.9
+105°C
f
= 433MHz
RF
+105°C
+85°C
1
+25°C
f
= 315MHz
RF
+85°C
+25°C
-40°C
0.1
0.01
-40°C
-117 -116
250
300
350
400
450
500
-121 -120 -119
-115 -114
-118
3.0
3.1
3.2
3.3
3.4
3.5
3.6
RF FREQUENCY (MHz)
AVERAGE INPUT POWER (dBm)
SUPPLY VOLTAGE (V)
RSSI AND DELTA
vs. IF INPUT POWER
RSSI vs. RF INPUT POWER
SENSITIVITY vs. TEMPERATURE
MAX1473 toc06
2.4
2.2
2.0
1.8
1.6
1.4
1.2
1.0
3.5
-105
-106
-107
-108
-109
-110
-111
-112
-113
-114
2.4
2.2
2.0
1.8
1.6
1.4
1.2
1.0
PEAK RF INPUT POWER
1% BER
IF BANDWIDTH = 280MHz
IF BANDWIDTH = 280kHz
2.5
V
= V
DD
AGCDIS
1.5
f
RF
= 433MHz
0.5
V
= 0V
AGCDIS
-0.5
-1.5
-2.5
-3.5
DELTA
RSSI
f
RF
= 315MHz
60
-140 -120 -100 -80 -60 -40 -20
RF INPUT POWER (dBm)
0
-40
-15
10
35
85
-90
-70
-50
-30
-10
10
110
TEMPERATURE (°C)
IF INPUT POWER (dBm)
IMAGE REJECTION
vs. RF FREQUENCY
IMAGE REJECTION
vs. TEMPERATURE
SYSTEM GAIN vs. FREQUENCY
55
50
45
40
35
30
45
45
44
44
43
43
42
42
41
41
30
20
f
RF
= 315MHz
UPPER
SIDEBAND
10
50dB IMAGE
REJECTION
LOWER
SIDEBAND
f
RF
= 375MHz
0
-10
-20
-30
f
RF
= 433MHz
f
RF
= 375MHz
FROM RFIN TO
MIXOUT
f
RF
= 315MHz
430
f
RF
= 433MHz
f
RF
= 315MHz
280
330
380
480
-40
-15
10
35
60
85
0
5
10
15
20
25
30
RF FREQUENCY (MHz)
TEMPERATURE (°C)
IF FREQUENCY (MHz)
6
_______________________________________________________________________________________
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
Typical Operating Characteristics (continued)
(Typical Application Circuit, V
= 3.3V, f = 315MHz, T = +25°C, unless otherwise noted.)
DD
RF
A
NORMALIZED IF GAIN
vs. IF FREQUENCY
S11 SMITH PLOT OF RFIN
S11 MAGNITUDE-LOG PLOT OF RFIN
MAX1473 toc12
5
30
20
600MHz
0
-5
10
0
-10
-20
-30
-40
-50
-60
-70
-10
-15
100MHz
315MHz
-34dB
-20
1
10
100
10 109 208 307 406 505 604 703 802 901 1000
RF FREQUENCY (MHz)
IF FREQUENCY (MHz)
PHASE NOISE
vs. OFFSET FREQUENCY
PHASE NOISE
vs. OFFSET FREQUENCY
REGULATOR VOLTAGE
vs. REGULATOR CURRENT
0
0
3.1
f
RF
= 315MHz
f
RF
= 433MHz
-20
-20
3.0
2.9
2.8
2.7
2.6
2.5
-40°C
-40
-60
-40
-60
+25°C
+85°C
+105°C
-80
-80
-100
-100
-120
-140
-120
-140
V
= 5.0V
DD
1.E-05 1.E-04 1.E-03 1.E-02 1.E-01 1.E+00 1.E+01
1.E-05 1.E-04 1.E-03 1.E-02 1.E-01 1.E+00 1.E+01
5
15
25
35
45
OFFSET FREQUENCY (MHz)
OFFSET FREQUENCY (MHz)
REGULATOR CURRENT (mA)
_______________________________________________________________________________________
7
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
Pin Description
PIN
NAME
FUNCTION
TSSOP
QFN
29
1
2, 7
3
XTAL1
1st Crystal Input. (See Phase-Locked Loop section.)
4, 30
31
AV
Positive Analog Supply Voltage for RF Sections. (See Typical Application Circuit.)
Low-Noise Amplifier Input. (See Low-Noise Amplifier section.)
DD
LNAIN
LNASRC
AGND
Low-Noise Amplifier Source for External Inductive Degeneration. Connect inductor to ground to
set LNA input impedance. (See Low-Noise Amplifier section.)
4
5
6
32
2
Analog Ground
Low-Noise Amplifier Output. Connect to mixer through an LC tank filter. (See Low-Noise
Amplifier section.)
3
LNAOUT
8
9
5
6
7
MIXIN1
MIXIN2
AGND
1st Differential Mixer Input. Connect through a 100pF capacitor to V
side of the LC tank.
DD
2nd Differential Mixer Input. Connect through a 100pF capacitor to LC tank filter from LNAOUT.
Analog Ground
10
Image Rejection Select Pin. Set V
= 0V to center image rejection at 315MHz. Leave IRSEL
IRSEL
11
8
IRSEL
floating to center image rejection at 375MHz. Set V
433MHz.
= V
to center image rejection at
IRSEL
DD
12
13
14
15
9
MIXOUT 330Ω Mixer Output. Connect to the input of the 10.7MHz bandpass filter.
10
11
12
DGND
DV
Digital Ground
Positive Digital Supply Voltage. Decouple to DGND with a 0.01µF capacitor.
DD
AGCDIS AGC Control Pin. Pull high to disable AGC.
Crystal Divider Ratio Select Pin. Drive XTALSEL low to select divider ratio of 64, or drive
XTALSEL high to select divider ratio of 32.
16
17
18
14
15
16
XTALSEL
1st Differential Intermediate Frequency Limiter Amplifier Input. Decouple to AGND with a 1500pF
capacitor.
IFIN1
2nd Differential Intermediate Frequency Limiter Amplifier Input. Connect to the output of a
10.7MHz bandpass filter.
IFIN2
19
20
21
22
23
24
25
26
27
28
17
18
19
20
22
23
24
26
27
28
DFO
DSN
OPP
DFFB
DSP
Data Filter Output
Negative Data Slicer Input
Noninverting Op-Amp Input for the Sallen-Key Data Filter
Data Filter Feedback Node. Input for the feedback of the Sallen-Key data filter.
Positive Data Slicer Input
V
5V Supply Voltage. V
is shorted to AV for 3.3V operation.
DD5 DD
DD5
DATAOUT Digital Baseband Data Output
PDOUT Peak Detector Output
PWRDN Power-Down Select Input. Drive this pin with a logic high to power on the IC.
XTAL2
2nd Crystal Input
1, 13,
21, 25
—
N.C.
No Connection
8
_______________________________________________________________________________________
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
C
C
TOTAL = C2 + PARASITICS
Detailed Description
L
and C
include inductance and
PARASITICS
PARASITICS
The MAX1473 CMOS superheterodyne receiver and a
few external components provide the complete receive
chain from the antenna to the digital output data.
Depending on signal power and component selection,
data rates as high as 100kbps can be achieved.
capacitance of the PC board traces, package pins,
mixer input impedance, LNA output impedance, etc.
These parasitics at high frequencies cannot be
ignored, and can have a dramatic effect on the tank fil-
ter center frequency. Lab experimentation should be
done to optimize the center frequency of the tank.
The MAX1473 is designed to receive binary ASK data
modulated in the 300MHz to 450MHz frequency range.
ASK modulation uses a difference in amplitude of the
carrier to represent logic 0 and logic 1 data.
Mixer
A unique feature of the MAX1473 is the integrated
image rejection of the mixer. This device eliminates the
need for a costly front-end SAW filter for most applica-
tions. Advantages of not using a SAW filter are
increased sensitivity, simplified antenna matching, less
board space, and lower cost.
Low-Noise Amplifier
The LNA is an NMOS cascode amplifier with off-chip
inductive degeneration that achieves approximately
16dB of power gain with a 2.0dB noise figure and an
IIP3 of -12dBm. The gain and noise figure are depen-
dent on both the antenna matching network at the LNA
input and the LC tank network between the LNA output
and the mixer inputs.
The mixer cell is a pair of double balanced mixers that
perform an IQ downconversion of the RF input to the
10.7MHz IF from a low-side injected LO (i.e., f = f
-
LO
RF
f ). The image-rejection circuit then combines these
IF
The off-chip inductive degeneration is achieved by
connecting an inductor from LNASRC to AGND. This
inductor sets the real part of the input impedance at
LNAIN, allowing for a more flexible input impedance
match, such as a typical PC board trace antenna. A
nominal value for this inductor with a 50Ω input imped-
ance is 15nH, but is affected by PC board trace. See
Typical Operating Characteristics for the relationship
between the inductance and the LNA input impedance.
signals to achieve a minimum 45dB of image rejection
over the full temperature range. Low-side injection is
required due to the on-chip image rejection architec-
ture. The IF output is driven by a source-follower biased
to create a driving impedance of 330Ω; this provides a
good match to the off-chip 330Ω ceramic IF filter. The
voltage conversion gain is approximately 13dB when
the mixer is driving a 330Ω load.
The IRSEL pin is a logic input that selects one of the
three possible image-rejection frequencies. When
The AGC circuit monitors the RSSI output. When the
RSSI output reaches 2.05V, which corresponds to an
RF input level of approximately -57dBm, the AGC
switches on the LNA gain reduction resistor. The resis-
tor reduces the LNA gain by 35dB, thereby reducing
the RSSI output by about 500mV. The LNA resumes
high-gain mode when the RSSI level drops back below
1.45V (approximately -65dBm at RF input) for 150ms.
The AGC has a hysteresis of ~8dB. With the AGC func-
tion, the MAX1473 can reliably produce an ASK output
for RF input levels up to 0dBm with a modulation depth
of 18dB.
V
V
= 0V, the image rejection is tuned to 315MHz.
= V /2 tunes the image rejection to 375MHz,
IRSEL
IRSEL
DD
and when V
= V , the image rejection is tuned to
DD
IRSEL
433MHz. The IRSEL pin is internally set to V /2 (image
DD
rejection at 375MHz) when it is left floating, thereby
eliminating the need for an external V /2 voltage.
DD
Phase-Locked Loop
The PLL block contains a phase detector, charge
pump/integrated loop filter, VCO, asynchronous 64x
clock divider, and crystal oscillator driver. Besides the
crystal, this PLL does not require any external compo-
nents. The VCO generates a low-side local oscillator
(LO). The relationship between the RF, IF, and refer-
ence frequencies is given by:
The LC tank filter connected to LNAOUT comprises L3
and C2 (see Typical Application Circuit). Select L3 and
C2 to resonate at the desired RF input frequency. The
resonant frequency is given by:
f
= (f - f ) / (32 ✕ M)
RF IF
REF
1
f =
where:
2π L
C
TOTAL × TOTAL
M = 1 (V
= V ) or 2 (V
= 0V)
XTALSEL
XTALSEL
DD
To allow the smallest possible IF bandwidth (for best
sensitivity), the tolerance of the reference must be mini-
mized.
where:
L
= L3 + L
PARASITICS
TOTAL
_______________________________________________________________________________________
9
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
Intermediate Frequency/RSSI
Applications Information
The IF section presents a differential 330Ω load to pro-
vide matching for the off-chip ceramic filter. The six
internal AC-coupled limiting amplifiers produce an
overall gain of approximately 65dB, with a bandpass fil-
ter-type response centered near the 10.7MHz IF fre-
quency with a 3dB bandwidth of approximately
11.5MHz. The RSSI circuit demodulates the IF by pro-
ducing a DC output proportional to the log of the IF sig-
nal level, with a slope of approximately 14.2mV/dB (see
Typical Operating Characteristics).
Crystal Oscillator
The XTAL oscillator in the MAX1473 is designed to pre-
sent a capacitance of approximately 3pF between the
XTAL1 and XTAL2. If a crystal designed to oscillate
with a different load capacitance is used, the crystal is
pulled away from its stated operating frequency, intro-
ducing an error in the reference frequency. Crystals
designed to operate with higher differential load capac-
itance always pull the reference frequency higher. For
example, a 4.7547MHz crystal designed to operate
with a 10pF load capacitance oscillates at 4.7563MHz
with the MAX1473, causing the receiver to be tuned to
315.1MHz rather than 315.0MHz, an error of about
100kHz, or 320ppm.
The AGC circuit monitors the RSSI output. When the
RSSI output reaches 2.05V, which corresponds to an
RF input level of approximately -57dBm, the AGC
switches on the LNA gain reduction resistor. The resis-
tor reduces the LNA gain by 35dB, thereby reducing
the RSSI output by about 500mV. The LNA resumes
high-gain mode when the RSSI level drops back below
1.45V (approximately -65dBm at RF input) for 150ms.
The AGC has a hysteresis of ~8dB. With the AGC func-
tion, the MAX1473 can reliably produce an ASK output
for RF input levels up to 0dBm with modulation depth of
18dB.
In actuality, the oscillator pulls every crystal. The crys-
tal’s natural frequency is really below its specified fre-
quency, but when loaded with the specified load
capacitance, the crystal is pulled and oscillates at its
specified frequency. This pulling is already accounted
for in the specification of the load capacitance.
Table 1. Component Values for Typical Application Circuit
COMPONENT
VALUE FOR 433MHz RF
VALUE FOR 315MHz RF
DESCRIPTION
L1
L2
56nH
110nH
Toko LL1608-FH
15nH
15nH
Murata LQP11A
L3
15nH
27nH
Murata LQP11A
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
C13
R1
100pF
100pF
5%
2.7pF
4.7pF
0.1pF
100pF
100pF
5%
100pF
100pF
5%
1500pF
1500pF
10%
220pF
220pF
5%
470pF
470pF
5%
0.47µF
0.47µF
20%
220pF
220pF
10%
0.01µF
0.01µF
20%
0.01µF
0.01µF
20%
Depends on XTAL
Depends on XTAL
5%
15pF
15pF
15pF
15pF
5kΩ
5kΩ
X1
6.6128MHz or 13.2256MHz
10.7MHz ceramic filter
4.7547MHz or 9.5094MHz
10.7MHz ceramic filter
—
X2
Murata SFECV10.7 series
10 ______________________________________________________________________________________
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
Additional pulling can be calculated if the electrical
parameters of the crystal are known. The frequency
pulling is given by:
MAX1473
C
1
1
6
m
f
=
-
×10
p
2
C
C
C
C
case + spec
RSSI
R
case + load
where:
f is the amount the crystal frequency pulled in ppm.
R
DF1
100kΩ
DF2
100kΩ
p
C
C
C
C
is the motional capacitance of the crystal.
m
22
DFFB
19
DFO
21
OPP
is the case capacitance.
case
spec
load
C6
C5
is the specified load capacitance.
is the actual load capacitance.
When the crystal is loaded as specified, i.e., C
spec
=
load
C
, the frequency pulling equals zero.
Data Filter
Figure 1. Sallen-Key Lowpass Data Filter
The data filter is implemented as a 2nd-order lowpass
Sallen-Key filter. The pole locations are set by the com-
bination of two on-chip resistors and two external
capacitors. Adjusting the value of the external capaci-
tors changes the corner frequency to optimize for dif-
ferent data rates. The corner frequency should be set
to approximately 1.5 times the fastest expected data
rate from the transmitter. Keeping the corner frequency
near the data rate rejects any noise at higher frequen-
cies, resulting in an increase in receiver sensitivity.
Choosing standard capacitor values changes C5 to
470pF and C6 to 220pF, as shown in the Typical
Application Circuit.
Table 2. Coefficents to Calculate C5 and C6
FILTER TYPE
Butterworth (Q = 0.707)
Bessel (Q = 0.577)
a
b
1.414
1.3617
1.000
0.618
The configuration shown in Figure 1 can create a
Butterworth or Bessel response. The Butterworth filter
offers a very flat amplitude response in the passband
and a rolloff rate of 40dB/decade for the two-pole filter.
The Bessel filter has a linear phase response, which
works well for filtering digital data. To calculate the
value of C5 and C6, use the following equations along
with the coefficients in Table 2:
Data Slicer
The purpose of the data slicer is to take the analog out-
put of the data filter and convert it to a digital signal.
This is achieved by using a comparator and comparing
the analog input to a threshold voltage. One input is
supplied by the data filter output. Both comparator
inputs are accessible off chip to allow for different
methods of generating the slicing threshold, which is
applied to the second comparator input.
b
C5 =
The suggested data slicer configuration uses a resistor
(R1) connected between DSN and DSP with a capaci-
tor (C4) from DSN to DGND (Figure 2). This configura-
tion averages the analog output of the filter and sets the
threshold to approximately 50% of that amplitude. With
this configuration, the threshold automatically adjusts
as the analog signal varies, minimizing the possibility
for errors in the digital data. The sizes of R1 and C4
affect how fast the threshold tracks to the analog ampli-
tude. Be sure to keep the corner frequency of the RC
circuit much lower than the lowest expected data rate.
a 100k π f
(
)( )(
c
)
)
a
C6 =
4 100k π f
(
)( )(
c
where f is the desired 3dB corner frequency.
C
For example, choose a Butterworth filter response with
a corner frequency of 5kHz:
1.000
C5 =
≈ 450pF
Note that a long string of zeros or 1’s can cause the
threshold to drift. This configuration works best if a cod-
1.414 100kΩ 3.14 5kHz
(
)(
)(
)(
)
______________________________________________________________________________________ 11
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
MAX1473
MAX1473
DATA
SLICER
DATA
SLICER
25
20
19
DFO
23
DSP
25
DATAOUT
20
DSN
23
DSP
19
DFO
DATAOUT
DSN
R4
R1
R2
R3
R1
C4
C4
*OPTIONAL
Figure 2. Generating Data Slicer Threshold
Figure 3. Generating Data Slicer Hysteresis
ing scheme, such as Manchester coding, which has an
equal number of zeros and 1’s, is used.
To prevent continuous toggling of DATAOUT in the
absence of an RF signal due to noise, hysteresis can
be added to the data slicer as shown in Figure 3.
MAX1473
Peak Detector
The peak detector output (PDOUT), in conjunction with
an external RC filter, creates a DC output voltage equal
to the peak value of the data signal. The resistor pro-
vides a path for the capacitor to discharge, allowing the
peak detector to dynamically follow peak changes of
the data filter output voltage. For faster receiver startup,
the circuit shown in Figure 4 can be used.
DATA
SLICER
25
DATAOUT
23
19
DFO
26
PDOUT
20
DSN
DSP
25kΩ
Layout Considerations
A properly designed PC board is an essential part of
any RF/microwave circuit. On high-frequency inputs
and outputs, use controlled-impedance lines and keep
them as short as possible to minimize losses and radia-
tion. At high frequencies, trace lengths that are on the
order of λ/10 or longer act as antennas.
47nF
Figure 4. Using PDOUT for Faster Startup
Keeping the traces short also reduces parasitic induc-
tance. Generally, 1in of a PC board trace adds about
20nH of parasitic inductance. The parasitic inductance
can have a dramatic effect on the effective inductance
of a passive component. For example, a 0.5in trace
connecting a 100nH inductor adds an extra 10nH of
inductance or 10%.
Chip Information
TRANSISTOR COUNT: 3035
PROCESS: CMOS
To reduce the parasitic inductance, use wider traces
and a solid ground or power plane below the signal
traces. Also, use low-inductance connections to ground
on all GND pins, and place decoupling capacitors
close to all V
connections.
DD
12 ______________________________________________________________________________________
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
Typical Application Circuit
VDD5
VDD3
X1
C12
C13
C11
1
2
3
4
5
6
7
8
9
28
27
26
25
24
23
22
21
20
19
18
17
16
15
XTAL1
AV
XTAL2
PWRDN
RF INPUT
TO/FROM µP
POWER DOWN
DATA OUT
DD
C1
L1
LNAIN
PDOUT
MAX1473
LNASRC
AGND
DATAOUT
L2
R2
V
DD5
R3
LNAOUT
DSP
DFFB
VDD3
L3
AV
DD
C3
C4
C2
MIXIN1
MIXIN2
AGND
OPP
C7
DSN
10
DFO
C9
11
12
13
14
IRSEL
IFIN2
R1
MIXOUT
DGND
IFIN1
XTALSEL
AGCDIS
DV
DD
X2
C5
C6
C8
IF FILTER
C10
IN
OUT
GND
COMPONENT VALUES
IN TABLE 1
______________________________________________________________________________________ 13
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
Functional Diagram
LNASRC
4
AGCDIS LNAOUT MIXIN1 MIXIN2
IRSEL
11
MIXOUT
12
IFIN1 IFIN2
17 18
15
6
8
9
0˚
IF LIMITING
AMPS
AUTOMATIC
GAIN
CONTROL
3
Q
I
LNA
LNAIN
IMAGE
REJECTION
∑
2,7
24
90˚
AVDD
VDD5
3.3V REG
MAX1473
RSSI
DATA
FILTER
DIVIDE
BY 64
14
13
VCO
DVDD
R
R
DF1
100kΩ
DF2
100kΩ
PHASE
DETECTOR
LOOP
FILTER
DGND
AGND
DATA
SLICER
5,10
÷1
÷2
CRYSTAL
DRIVER
POWER
DOWN
16
1
28
27
25
20 23 19
26
21
22
DFFB
XTALSEL
XTAL1 XTAL2
PWRDN DATAOUT
DSN DSP DFO
PDOUT OPP
14 ______________________________________________________________________________________
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
______________________________________________________________________________________ 15
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
D2
0.15
C A
D
b
0.10 M
C A B
C
L
D2/2
D/2
k
PIN # 1
I.D.
0.15
C
B
PIN # 1 I.D.
0.35x45
E/2
E2/2
C
(NE-1) X
e
L
E2
E
k
L
DETAIL A
e
(ND-1) X
e
C
C
L
L
L
L
e
e
0.10
C
A
0.08
C
C
A3
A1
PROPRIETARY INFORMATION
TITLE:
PACKAGE OUTLINE
16, 20, 28, 32L, QFN THIN, 5x5x0.8 mm
APPROVAL
DOCUMENT CONTROL NO.
REV.
1
21-0140
C
2
16 ______________________________________________________________________________________
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
COMMON DIMENSIONS
EXPOSED PAD VARIATIONS
NOTES:
1. DIMENSIONING & TOLERANCING CONFORM TO ASME Y14.5M-1994.
2. ALL DIMENSIONS ARE IN MILLIMETERS. ANGLES ARE IN DEGREES.
3. N IS THE TOTAL NUMBER OF TERMINALS.
4. THE TERMINAL #1 IDENTIFIER AND TERMINAL NUMBERING CONVENTION SHALL CONFORM TO JESD 95-1
SPP-012. DETAILS OF TERMINAL #1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED WITHIN THE
ZONE INDICATED. THE TERMINAL #1 IDENTIFIER MAY BE EITHER A MOLD OR MARKED FEATURE.
5. DIMENSION b APPLIES TO METALLIZED TERMINAL AND IS MEASURED BETWEEN 0.25 mm AND 0.30 mm
FROM TERMINAL TIP.
6. ND AND NE REFER TO THE NUMBER OF TERMINALS ON EACH D AND E SIDE RESPECTIVELY.
7. DEPOPULATION IS POSSIBLE IN A SYMMETRICAL FASHION.
8. COPLANARITY APPLIES TO THE EXPOSED HEAT SINK SLUG AS WELL AS THE TERMINALS.
9. DRAWING CONFORMS TO JEDEC MO220.
PROPRIETARY INFORMATION
TITLE:
PACKAGE OUTLINE
10. WARPAGE SHALL NOT EXCEED 0.10 mm.
16, 20, 28, 32L, QFN THIN, 5x5x0.8 mm
APPROVAL
DOCUMENT CONTROL NO.
REV.
2
21-0140
C
2
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 17
© 2003 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
相关型号:
©2020 ICPDF网 联系我们和版权申明