LT1010_06 [Linear]
Fast 【150mA Power Buffer; 快速±150mA的电源缓冲型号: | LT1010_06 |
厂家: | Linear |
描述: | Fast 【150mA Power Buffer |
文件: | 总20页 (文件大小:271K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LT1010
Fast ±150mA Power Buffer
U
FEATURES
DESCRIPTIO
The LT®1010 is a fast, unity-gain buffer that can increase
the output capability of existing IC op amps by more than
an order of magnitude. This easy-to-use part makes fast
amplifiers less sensitive to capacitive loading and reduces
thermal feedback in precision DC amplifiers.
■
20MHz Bandwidth
■
75V/µs Slew Rate
■
Drives ±10V into 75Ω
5mA Quiescent Current
Drives Capacitive Loads > 1µF
Current and Thermal Limit
■
■
■
Designed to be incorporated within the feedback loop, the
buffer can isolate almost any reactive load. Speed can be
improved with a single external resistor. Internal operat-
ing currents are essentially unaffected by the supply
voltage range. Single supply operation is also practical.
■
Operates from Single Supply ≥ 4.5V
■
Very Low Distortion Operation
■
Available in 8-Pin miniDIP, Plastic TO-220
and Tiny 3mm × 3mm × 0.75mm 8-Pin DFN
Packages
This monolithic IC is supplied in 8-pin miniDIP, plastic
TO-220 and 8-pin DFN packages. The low thermal resis-
tance power package is an aid in reducing operating
junction temperatures.
U
APPLICATIO S
■
Boost Op Amp Output
■
Isolate Capacitive Loads
, LT, LTC and LTM are registered trademarks of Linear Technology Corporation.
All other trademarks are the property of their respective owners.
■
Drive Long Cables
■
Audio Amplifiers
■
Video Amplifiers
■
Power Small Motors
■
Operational Power Supply
■
FET Driver
U
TYPICAL APPLICATIO
Very Low Distortion Buffered Preamplifier
+
V
0.4
18V
C2
22pF
V
= 10V
OUT
L
P-P
R7
50Ω
R
= 400Ω
R1
1k
+
0.3
0.2
0.1
0
V
3
2
7
R6
R8
100Ω
+
BOOST
100Ω
IN
OUT
6
OUTPUT
LT1056CN8
LT1010CT
C1
22pF
R2
1M
–
–
4
R3
1k
R4
10k
V
+
V
LM334
= 2mA
NOTE 1: ALL RESISTORS 1% METAL FILM
NOTE 2: SUPPLIES WELL BYPASSED AND LOW Z
R
SET
33.2Ω
O
–
I
V
SET
1%
10
100
1k
10k
100k
+
FREQUENCY (Hz)
V
–18V
1010 TA01
1010 TA02
1010fc
1
LT1010
W W
U W
U
U U
ABSOLUTE AXI U RATI GS
PRECO DITIO I G
(Note 1)
100% Thermal Limit Burn In–LT1010CT
Total Supply Voltage.............................................. ±22V
Continuous Output Current.............................. ±150mA
Input Current (Note 3) ....................................... ±40mA
Operating Junction Temperature Range
LT1010C............................................... 0°C to 100°C
Storage Temperature Range ................. –65°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
U W
U
PACKAGE/ORDER I FOR ATIO
TOP VIEW
FRONT VIEW
5
TOP VIEW
+
V
BIAS
OUT
NC
1
2
3
4
8
7
6
5
INPUT
NC
OUTPUT
+
V
1
2
3
4
8
7
6
5
INPUT
NC
4
3
2
1
BIAS
–
BIAS
OUT
NC
9
–
–
V
V
V
(TAB)
V
–
V
+
NC
NC
INPUT
DD PACKAGE
8-LEAD (3mm × 3mm) PLASTIC DFN
T PACKAGE
5-LEAD PLASTIC TO-220
N8 PACKAGE
8-LEAD PDIP
TJMAX = 100°C, θJC = 3°C/W, θJA = 40°C/W
EXPOSED PAD (PIN 9) V– CAN BE SOLDERED TO PCB
TO REDUCE THERMAL RESISTANCE (NOTE 7)
TJMAX = 100°C, θJC = 45°C/W, θJA = 100°C/W
TJMAX = 125°C, θJC = 3°C/W, θJA = 50°C/W
ORDER PART
NUMBER
DD PART
MARKING
ORDER PART
NUMBER
ORDER PART
NUMBER
LT1010CDD
LBWZ
LT1010CN8
LT1010CT
Order Options Tape and Reel: Add #TR
Lead Free: Add #PBF Lead Free Tape and Reel: Add #TRPBF
Lead Free Part Marking: http://www.linear.com/leadfree/
Consult LTC Marketing for parts specified with wider operating temperature ranges.
ELECTRICAL CHARACTERISTICS
The
●
indicates specifications which apply over the full operating
temperature range, otherwise specifications are at T = 25°C. (See Note 4. Typical values in curves.)
A
SYMBOL PARAMETER
CONDITIONS (Note 4)
MIN
TYP
MAX
UNITS
V
OS
Output Offset Voltage
(Note 4)
0
–20
150
220
mV
mV
●
V = ± 15V, V = 0V
20
100
mV
S
IN
I
Input Bias Current
I
I
= 0mA
≤ 150mA
0
0
0
250
500
800
µA
µA
µA
B
OUT
OUT
●
●
A
Large-Signal Voltage Gain
Output Resistance
0.995
1.00
V/V
V
R
I
I
= ±1mA
= ±150mA
5
5
10
10
12
Ω
Ω
Ω
OUT
OUT
OUT
●
Slew Rate
V = ±15V, V = ±10V,
75
V/µs
S
V
IN
= ±8V, R = 100Ω
OUT
L
1010fc
2
LT1010
ELECTRICAL CHARACTERISTICS
The
●
indicates specifications which apply over the full operating
temperature range, otherwise specifications are at T = 25°C. (See Note 4. Typical values in curves.)
A
SYMBOL PARAMETER
CONDITIONS (Note 4)
MIN
TYP
MAX
UNITS
+
V
Positive Saturation Offset
Negative Saturation Offset
Saturation Resistance
Bias Terminal Voltage
Supply Current
I
I
I
= 0 (Note 5)
1.0
1.1
V
V
SOS
OUT
OUT
OUT
●
●
●
●
●
–
V
= 0 (Note 5)
0.2
0.3
V
V
SOS
R
= ±150mA (Note 5)
22
28
Ω
Ω
SAT
V
R
= 20Ω (Note 6)
700
560
840
880
mV
mV
BIAS
BIAS
I
I
= 0, I = 0
BIAS
9
10
mA
mA
S
OUT
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: For case temperatures above 25°C, dissipation must be derated
based on a thermal resistance of 25°C/W for the T package, 130°C/W for
the N8 package and 40°C/W for the DD package for ambient temperatures
above 25°C. See Applications Information.
Note 5: The output saturation characteristics are measured with 100mV
output clipping. See Applications Information for determining available
output swing and input drive requirements for a given load.
Note 6: The output stage quiescent current can be increased by
+
connecting a resistor between the BIAS pin and V . The increase is
equal to the bias terminal voltage divided by this resistance.
Note 7: Thermal resistance varies depending upon the amount of PC board
metal attached to the pin (Pin 9) of the device. θ is specified for a certain
JA
Note 3: In current limit or thermal limit, input current increases sharply
amount of 1oz copper metal trace connecting to Pin 9 as described in the
thermal resistance tables in the Applications Information section.
with input-output differentials greater than 8V; so input current must be
+
limited. Input current also rises rapidly for input voltages 8V above V or
–
0.5V below V .
Note 4: Specifications apply for 4.5V ≤ V ≤ 40V,
S
–
+
V
+ 0.5V ≤ V ≤ V – 1.5V and I
= 0, unless otherwise stated.
Temperature range is 0°C ≤ T ≤ 100°C, T ≤ 100°C.
IN
OUT
J
C
1010fc
3
LT1010
TYPICAL PERFOR A CE CHARACTERISTICS
U W
Bandwidth
Phase Lag
Phase Lag
50
40
30
20
10
0
50
50
R
= 200Ω
= 50Ω
L
R
20
10
5
20
10
5
L
R
L
= 50Ω
R
L
= 50Ω
R = 200Ω
L
R
L
= 200Ω
V
C
A
= 100mV
100pF
C
= 100pF
C = 100pF
L
IN
L
V
P-P
L
S
R
= 50Ω
R
= 50Ω
S
= –3dB
I
= 0
R
= 20Ω
BIAS
BIAS
T = 25°C
J
T = 25°C
T = 25°C
J
J
0
20
30
2
5
10
20
2
5
10
20
10
40
FREQUENCY (MHz)
FREQUENCY (MHz)
QUIESCENT CURRENT (mA)
1010 G02
1010 G03
1010 G01
Small-Step Response
Output Impedance
Capacitive Loading
100
10
1
150
100
50
10
0
I
= 0
R
J
= 100Ω
R
I
J
= 50Ω
BIAS
T = 25°C
BIAS
J
L
S
T
= 25°C
T = 25°C
= 0
INPUT
OUTPUT
3nF
100pF
0
–50
–100
–150
–10
–20
0.1µF
0.1
1
10
100
0
10
20
30
0.1
1
10
100
FREQUENCY (MHz)
TIME (ns)
FREQUENCY (MHz)
1010 G05
1010 G04
1010 G06
Slew Response
Negative Slew Rate
Supply Current
80
60
40
20
0
20
400
300
200
100
0
V
V
= ±15V
= ±10V
V
= ±15V
IN
S
IN
= 0
S
0 ≥ V ≥ –10V
15
10
5
I
L
POSITIVE
= ±15V
R
= 200Ω
= 100Ω
T
= 25°C
L
C
R
L
V
S
R
= 100Ω
L
T = 25°C
0
J
I
= 0
BIAS
R
= 50Ω
L
f ≤ 1MHz
–5
NEGATIVE
–10
–15
–20
R
= 20Ω
BIAS
0
50
150
20
–50
200
250
0
10
30
40
100
0
1
2
3
4
5
TIME (ns)
QUIESCENT CURRENT (mA)
FREQUENCY (MHz)
1010 G07
1010 G08
1010 G09
1010fc
4
LT1010
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Output Offset Voltage
Input Bias Current
Input Bias Current
200
150
100
50
200
150
100
50
200
150
100
50
V
= 0
V
= ±15V
= 75Ω
V
= 0
IN
S
L
IN
R
T = 125°C
J
+
–
V
V
= 38V
= –2V
+
–
V
V
= 38V
= –2V
T = 25°C
J
+
–
V
V
= 2V
= –38V
+
–
T = –55°C
J
V
V
= 2V
= –38V
0
0
0
50
–50
0
50
100
150
–100 –50
50
–50
0
100
150
–150
100
150
0
TEMPERATURE (°C)
TEMPERATURE (°C)
OUTPUT CURRENT (mA)
1010 G10
1010 G10
1010 G12
Voltage Gain
Output Resistance
Output Noise Voltage
12
200
150
100
50
1.000
0.999
0.998
I
≤ 150mA
I
= 0
T = 25°C
J
OUT
OUT
10
8
V
S
= 40V
6
V
S
= 4.5V
4
R
= 1k
S
R
= 50Ω
S
2
0.997
0
0
100
TEMPERATURE (°C)
100
TEMPERATURE (°C)
–50
0
50
150
–50
0
50
150
10
100
1k
10k
FREQUENCY (Hz)
1010 G15
1010 G14
1010 G13
Positive Saturation Voltage
Negative Saturation Voltage
Supply Current
4
3
2
1
0
7
6
5
4
3
4
3
2
1
0
V
= 0
= 0
= 0
IN
I
I
OUT
BIAS
T = –55°C
I
= –150mA
I
= 150mA
J
L
L
T = 25°C
J
I
L
= –50mA
= –5mA
I
= 50mA
= 5mA
L
T = 125°C
J
I
I
L
L
50
20
–50
0
100
150
0
10
30
40
50
–50
0
100
150
TEMPERATURE (°C)
TOTAL SUPPLY VOLTAGE (V)
TEMPERATURE (°C)
1010 G16
1010 G18
1010 G16
1010fc
5
LT1010
TYPICAL PERFOR A CE CHARACTERISTICS
U W
Bias Terminal Voltage
Total Harmonic Distortion
Total Harmonic Distortion
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
0.8
0.6
0.4
0.2
0
V
S
= ±20V
R
= 50Ω
I
= 0
L
BIAS
S
f = 10kHz
V
V
T
= ±15V
V
T
= ±15V
= 25°C
= ±10V
OUT
= 25°C
S
C
C
R
BIAS
= 100Ω
R
BIAS
= 20Ω
I
= 0
R
= 50Ω
BIAS
BIAS
R
L
= 50Ω
R
L
= 100Ω
–50
50
100
0
150
0.1
1
10
100
1
10
100
1000
TEMPERATURE (°C)
OUTPUT VOLTAGE (V
)
P-P
FREQUENCY (kHz)
1010 G20
1010 G21
1010 G19
Shorted Input Characteristics
Peak Power Capability
Peak Output Current
10
8
0.5
0.4
0.3
0.2
0.1
0
50
25
T = 85°C
C
V
V
= ±15V
OUT
V
V
J
= ±15V
OUT
T = 25°C
S
S
= 0
= 0
SINK
6
SOURCE
0
TO-220
4
–25
2
0
–50
1
10
PULSE WIDTH (ms)
100
–10
–5
5
–50
50
100
–15
10
15
0
150
0
TEMPERATURE (°C)
INPUT VOLTAGE (V)
1010 G23
1010 G24
1010 G22
1010fc
6
LT1010
W U U
APPLICATIO S I FOR ATIO
U
General
idealized buffer with the unloaded gain specified for the
LT1010. Otherwise, it has zero offset voltage, bias current
and output resistance. Its output also saturates to the
internal supply terminals2.
These notes briefly describe the LT1010 and how it is
used; a detailed explanation is given elsewhere1. Empha-
sis here will be on practical suggestions that have resulted
from working extensively with the part over a wide range
of conditions. A number of applications are also outlined
that demonstrate the usefulness of the buffer beyond that
of driving a heavy load.
+
V
+
V
SOS
I
B
R′
V
OS
+
R
OUT
Design Concept
INPUT
A1
OUTPUT
The schematic below describes the basic elements of the
buffer design. The op amp drives the output sink transis-
tor, Q3, such that the collector current of the output
follower, Q2, never drops below the quiescent value (de-
terminedbyI1 andthearearatioofD1andD2). Asaresult,
the high frequency response is essentially that of a simple
follower even when Q3 is supplying the load current. The
internal feedback loop is isolated from the effects of
capacitive loading by a small resistor in the output lead.
R′ R′= R
– R
OUT
SAT
–
V
SOS
–
V
1010 AI02
Loaded voltage gain can be determined from the unloaded
gain, AV, the output resistance, ROUT, and the load resis-
tance, RL, using:
AVRL
ROUT + RL
AVL
=
+
V
D1
D2
Maximum positive output swing is given by:
BIAS
I
–
+
2
(V+ – VSOS+ )RL
RSAT + RL
The input swing required for this output is:
+
VOUT
=
Q2
A1
INPUT
Q1
R1
I
OUTPUT
1
Q3
⎛
⎞
ROUT
RL
–
+
+
V
V
IN
= VOUT 1+
– VOS + ∆VOS
1010 AI01
⎜
⎟
⎝
⎠
The scheme is not perfect in that the rate of rise of sink
current is noticeably less than for source current. This can
be mitigated by connecting a resistor between the bias
terminalandV+, raisingquiescentcurrent. Afeatureofthe
finaldesignisthattheoutputresistanceislargelyindepen-
dent of the follower quiescent current or the output load
current. The output will also swing to the negative rail,
which is particularly useful with single supply operation.
where ∆VOS is the 100mV clipping specified for the
saturation measurements. Negative output swing and
input drive requirements are similarly determined.
Supply Bypass
The buffer is no more sensitive to supply bypassing than
slower op amps as far as stability is concerned. The 0.1µF
disc ceramic capacitors usually recommended for op
amps are certainly adequate for low frequency work. As
always, keeping the capacitor leads short and using a
1R. J. Widlar, “Unique IC Buffer Enhances Op Amp Designs; Tames Fast Amplifiers,”
Linear Technology Corp. TP-1, April, 1984.
2See electrical characteristics section for guaranteed limits.
Equivalent Circuit
Below 1MHz, the LT1010 is quite accurately represented
by the equivalent circuit shown here for both small- and
large-signal operation. The internal element, A1, is an
1010fc
7
LT1010
W U U
U
APPLICATIO S I FOR ATIO
groundplaneisprudent,especiallywhenoperatingathigh
frequencies.
without limiting. Because of this, it is capable of power
dissipation in excess of its continuous ratings.
Thebufferslewratecanbereducedbyinadequatesupply
bypass. With output current changes much above
100mA/µs, using 10µF solid tantalum capacitors on both
supplies is good practice, although bypassing from the
positive to the negative supply may suffice.
Normally, thermal overload protection will limit dissipa-
tion and prevent damage. However, with more than 30V
across the conducting output transistor, thermal limiting
is not quick enough to ensure protection in current limit.
The thermal protection is effective with 40V across the
conducting output transistor as long as the load current is
otherwise limited to 150mA.
When used in conjunction with an op amp and heavily
loaded (resistive or capacitive), the buffer can couple into
supply leads common to the op amp causing stability
problems with the overall loop and extended settling time.
Adequatebypassingcanusuallybeprovidedby10µFsolid
tantalum capacitors. Alternately, smaller capacitors could
beusedwithdecouplingresistors. Sometimestheopamp
has much better high frequency rejection on one supply,
so bypass requirements are less on this supply.
Drive Impedance
When driving capacitive loads, the LT1010 likes to be
driven from a low source impedance at high frequencies.
Certain low power op amps (e.g., the LM10) are marginal
in this respect. Some care may be required to avoid
oscillations, especially at low temperatures.
Bypassingthebufferinputwithmorethan200pFwillsolve
the problem. Raising the operating current also works.
Power Dissipation
In many applications the LT1010 will require heat sink-
ing. Thermal resistance, junction to still air is 100°C/W
for the TO-220 package and 130°C/W for the miniDIP
package. Circulating air, a heat sink or mounting the
package to a printed circuit board will reduce thermal
resistance.
Parallel Operation
Parallel operation provides reduced output impedance,
more drive capability and increased frequency response
under load. Any number of buffers can be directly paral-
leled as long as the increased dissipation in individual
units caused by mismatches of output resistance and
offset voltage is taken into account.
In DC circuits, buffer dissipation is easily computed. In AC
circuits, signal waveshape and the nature of the load
determine dissipation. Peak dissipation can be several
times average with reactive loads. It is particularly impor-
tant to determine dissipation when driving large load
capacitance.
When the inputs and outputs of two buffers are connected
together, a current, ∆IOUT, flows between the outputs:
VOS1 – VOS2
ROUT1 + ROUT2
∆IOUT
=
With AC loading, power is divided between the two output
transistors. This reduces the effective thermal resistance,
junctiontocaseto15°C/WfortheTO-220packageaslong
as the peak rating of neither output transistor is exceeded.
The typical curves indicate the peak dissipation capabili-
ties of one output transistor.
where VOS and ROUT are the offset voltage and output
resistance of the respective buffers.
Normally, the negative supply current of one unit will
increase and the other decrease, with the positive supply
current staying the same. The worst-case (VIN → V+)
increase in standby dissipation can be assumed to be
∆IOUTVT, where VT is the total supply voltage.
Overload Protection
The LT1010 has both instantaneous current limit and
thermaloverloadprotection.Foldbackcurrentlimitinghas
not been used, enabling the buffer to drive complex loads
Offset voltage is specified worst case over a range of
supply voltages, input voltage and temperature. It would
1010fc
8
LT1010
W U U
APPLICATIO S I FOR ATIO
U
be unrealistic to use these worst-case numbers above
because paralleled units are operating under identical
conditions. The offset voltage specified for VS = ±15V,
VIN = 0V and TA = 25°C will suffice for a worst-case
condition.
Atlowerfrequencies, thebufferiswithinthefeedbackloop
so that its offset voltage and gain errors are negligible. At
higher frequencies, feedback is through CF, so that phase
shift from the load capacitance acting against the buffer
output resistance does not cause loop instability.
+
V
Stability depends upon the RFCF time constant or the
closed-loop bandwidth. With an 80kHz bandwidth, ring-
ing is negligible for CL = 0.068µF and damps rapidly for
CL = 0.33µF. The pulse response is shown in the graph.
I
S
I
S
A1
LT1010
V
V
OUT
IN
Pulse Response
∆I
OUT
C
= 0.068µF
L
5
0
A2
LT1010
I
– ∆I
I + ∆I
S OUT
–5
S
OUT
1010 AI03
C
= 0.33µF
L
–
V
5
0
Output load current will be divided based on the output
resistance of the individual buffers. Therefore, the avail-
ableoutputcurrentwillnotquitebedoubledunlessoutput
resistances are matched. As for offset voltage, the 25°C
limits should be used for worst-case calculations.
–5
100
0
50
150
200
TIME (µs)
1010 AI05
Parallel operation is not thermally unstable. Should one
unit get hotter than its mates, its share of the output and
its standby dissipation will decrease.
Small-signal bandwidth is reduced by CF, but consider-
able isolation can be obtained without reducing it below
the power bandwidth. Often, a bandwidth reduction is
desirable to filter high frequency noise or unwanted
signals.
As a practical matter, parallel connection needs only some
increased attention to heat sinking. In some applications,
a few ohms equalization resistance in each output may be
wise. Only the most demanding applications should re-
quirematching, andthenjustofoutputresistanceat25°C.
R
F
2k
C
F
1nF
–
Isolating Capacitive Loads
A1
LT118A
A2
LT1010
R
S
V
OUT
2k
V
+
The inverting amplifier below shows the recommended
method of isolating capacitive loads. Noninverting ampli-
fiers are handled similarly.
IN
C
L
1010 AI06
R
F
R
20k
The follower configuration is unique in that capacitive
load isolation is obtained without a reduction in small-
signal bandwidth, although the output impedance of the
buffer comes into play at high frequencies. The precision
unity-gain buffer above has a 10MHz bandwidth without
capacitive loading, yet it is stable for all load capacitance
S
V
IN
C
F
100pF
–
A1
LT1007
A2
LT1010
V
OUT
+
C
L
1010 AI04
to over 0.3µF, again determined by RFCF.
1010fc
9
LT1010
W U U
U
APPLICATIO S I FOR ATIO
This is a good example of how fast op amps can be made
stage. Feedback is arranged in the conventional manner,
although the 68µF-0.01µF combination limits DC gain to
unity for all gain settings. For applications sensitive to
NTSC requirements, dropping the 25Ω output stage bias
value will aid performance.
quite easy to use by employing an output buffer.
Integrator
A lowpass amplifier can be formed just by using large CF
in the inverter described earlier, as long as the increasing
closed-loopoutputimpedanceabovethecutofffrequency
is not a problem and the op amp is capable of supplying
the required current at the summing junction.
R2
800Ω
C1
15pF
–
A1
A2
LT1010
V
C
I
OUT
HA2625
1010 AI09
V
+
IN
I
IN
R
F
20k
R1
100Ω
–
A1
LT1012
A2
LT1010
V
OUT
1010 AI07
This shows the buffer being used with a wideband ampli-
fier that is not unity-gain stable. In this case, C1 cannot be
used to isolate large capacitive loads. Instead, it has an
optimum value for a limited range of load capacitances.
+
C
F
500pF
If the integrating capacitor must be driven from the buffer
output, thecircuitabovecanbeusedtoprovidecapacitive
loadisolation. Asbefore, thestabilitywithlargecapacitive
loads is determined by RFCF.
The buffer can cause stability problems in circuits like
this. With the TO-220 packages, behavior can be im-
proved by raising the quiescent current with a 20Ω
resistor from the bias terminal to V+. Alternately, devices
in the miniDIP can be operated in parallel.
Wideband Amplifiers
It is possible to improve capacitive load stability by
operating the buffer class A at high frequencies. This is
done by using quiescent current boost and bypassing the
bias terminal to V– with more than 0.02µF.
This simple circuit provides an adjustable gain video
amplifier that will drive 1VP-P into 75Ω. The differential
pair provides gain with the LT1010 serving as an output
15V
TYPICAL SPECIFICATIONS
R2
1.6k
1V INTO 75Ω
P-P
AT A = 2
0.5dB TO 10MHz
3dB DOWN AT 16MHz
AT A = 10
0.5dB TO 4MHz
–3dB = 8MHz
8.2k
25Ω
BIAS
+
–
+
22µF
A1
HA2625
A2
LT1010
22µF
OUTPUT
1010 AI10
INPUT
+
OUTPUT
(75Ω)
LT1010
R1
400Ω
–15V
PEAKING
5pF to 25pF
900Ω
Putting the buffer outside the feedback loop as shown
here will give capacitive load isolation, with large output
capacitors only reducing bandwidth. Buffer offset, re-
ferred to the op amp input, is divided by the gain. If the
load resistance is known, gain error is determined by the
INPUT
Q1 Q2
1k
Q1, Q2: 2N3866
GAIN SET
5.1k
–15V
+
0.01µF
68µF
1010 AI08
output resistance tolerance. Distortion is low.
1010fc
10
LT1010
W U U
U
APPLICATIO S I FOR ATIO
R3
current boost. The appearance is always worse with fast
rise signal generators than in practical applications.
800Ω
C1
R4
20pF
–
Track and Hold
39Ω
A2
LT1010
A1
HA2625
OUTPUT 1
INPUT
The5MHztrackandholdshownherehasa400kHzpower
bandwidth driving ±10V. A buffered input follower drives
the hold capacitor, C4, through Q1, a low resistance FET
switch. The positive hold command is supplied by TTL
logic with Q3 level shifting to the switch driver, Q2. The
output is buffered by A3.
+
R1
R2
50Ω 200Ω
R5
39Ω
A3
LT1010
OUTPUT 2
1010 AI11
Whenthegateisdrivento V– forHOLD, itpullschargeout
of the hold capacitor. A compensating charge is put into
the hold capacitor through C3. The step into hold is made
independentoftheinputlevelwithR7andadjustedtozero
with R10.
OTHER
SLAVES
The 50Ω video line splitter here puts feedback on one
buffer with the others slaved. Offset and gain accuracy of
slaves depend on their matching with master.
When driving long cables, including a resistor in series
withtheoutputshouldbeconsidered.Althoughitreduces
gain,itdoesisolatethefeedbackamplifierfromtheeffects
of unterminated lines which present a resonant load.
Since internal dissipation can be quite high when driving
fastsignalsintoacapacitiveload, usingabufferinapower
package is recommended. Raising buffer quiescent cur-
rent to 40mA with R3 improves frequency response.
When working with wideband amplifiers, special atten-
tion should always be paid to supply bypassing, stray
capacitance and keeping leads short. Direct grounding of
test probes, rather than the usual ground lead, is abso-
lutely necessary for reasonable results.
This circuit is equally useful as a fast acquisition sample
and hold. An LT1056 might be used for A3 to reduce drift
inholdbecauseitslowerslewrateisnotusuallyaproblem
in this application.
Current Sources
The LT1010 has slew limitations that are not obvious from
standard specifications. Negative slew is subject to
glitching, but this can be minimized with quiescent
A standard op amp voltage to current converter with a
buffer to increase output current is shown here. As usual,
+
V
R3
20Ω
R1
2k
–
Q1
A3
LT118A
INPUT
+
OUTPUT
2N5432
A1
LT118A
A2
LT1010
S
D
+
–
C1
C3
+
50pF
R2
2k
100pF
D2*
6V
A4
LT118A
C2
–
D1
HP2810
R4
2k
C4
1nF
150pF
R8
5k
R5
1k
Q3
2N2907
R9
10k
C5
10pF
Q2
2N2222
HOLD
R6
1k
R10
50k
R7
200k
R11
6.2k
1010 AI12
–
V
*2N2369 EMITTER BASE JUNCTION
1010fc
11
LT1010
W U U
U
APPLICATIO S I FOR ATIO
excellentmatchingofthefeedbackresistorsisrequiredto
get high output resistance. Output is bidirectional.
R2
2k
C1
1nF
–
R3
2Ω
A1
A2
OUTPUT
R1
100k
0.01%
R2
100k
0.01%
R2(V2 – V1)
R1R4
LT118A
LT1010
I
=
+
OUT
R4
2k
0.1%
R5
V1
2k
–
+
D1
1N457
0.1%
R4
A3
LT118A
10Ω
0.1%
–
A1
LT1012
A2
LT1010
C2
10pF
I
D2
1N457
OUT
R1
2k
R6
99.8k
0.1%
+
R3
100k
0.01%
R7
99.8k
0.1%
V
V
I
V
1010 AI13
V2
1V/V
10mA/V
R4
1010 AI15
100k
0.01%
Thiscircuitusesaninstrumentationamplifiertoeliminate
the matched resistors. The input is not high impedance
and must be driven from a low impedance source like an
op amp. Reversal of output sense can be obtained by
grounding Pin 7 of the LM163 and driving Pin 5.
enables the current regulator to get control of the output
currentfromthebuffercurrentlimitwithinamicrosecond
for an instantaneous short.
In the voltage regulation mode, A1 and A2 act as a fast
voltage follower using the capacitive load isolation tech-
niquedescribedearlier. Loadtransientrecoveryaswellas
capacitive load stability are determined by C1. Recovery
from short circuit is clean.
A2
LT1010
V
10R1
IN
I
=
OUT
Bidirectional current limit can be obtained by adding
another op amp connected as a complement to A3.
R1
10Ω
0.1%
V
IN
–
+
2
3
7
I
OUT
A1
6
Supply Splitter
LM163
×10
Dual supply op amps and comparators can be operated
from a single supply by creating an artificial ground at half
the supply voltage. The supply splitter shown here can
source or sink 150mA.
5
1010AI14
Output resistances of several megohms can be obtained
with both circuits. This is impressive considering the
±150mAoutputcapability.Highfrequencyoutputcharac-
teristicswilldependonthebandwidthandslewrateofthe
amplifiers. Both these circuits have an equivalent output
capacitance of about 30nF.
The output capacitor, C2, can be made as large as neces-
sary to absorb current transients. An input capacitor is
also used on the buffer to avoid high frequency instability
that can be caused by high source impedance.
+
V
Voltage/Current Regulator
C3
R1
0.1µF
10k
This circuit regulates the output voltage at VV until the
load current reaches a value programmed by VI. For
heavier loads, it is a precision current regulator.
A1
LT1010
+
V /2
R2
10k
C1
1nF
C2
0.01µF
With output currents below the current limit, the current
regulator is disconnected from the loop by D1 with D2
keeping its output out of saturation. This output clamp
1010 AI16
1010fc
12
LT1010
W U U
U
APPLICATIO S I FOR ATIO
High Current Booster
5V
Q1
The circuit below uses a discrete stage to get 3A output
capacity.Theconfigurationshownprovidesaclean,quick
way to increase LT1010 output power. It is useful for high
current loads such as linear actuator coils in disk drives.
INPUT
2N5486
A
B
A2
OUTPUT
10M
LT1010
–5V
0.1µF
The 33Ω resistors sense the LT1010’s supply current
with the grounded 100Ω resistor supplying a load for the
LT1010. The voltage drop across the 33Ω resistors
biases Q1 and Q2. Another 100Ω value closes a local
feedback loop, stabilizing the output stage. Feedback to
the LT1056 control amplifier is via the 10k value. Q3 and
Q4, sensing across the 0.18Ω units, furnish current
limiting at about 3.3A.
4
3
2
+
10k
A1
6
Q2
LTC1050
2N2222
–
0.01µF
7
100Ω
10M
2000pF
0.1µF
1k
5V
–5V
1010 AI18
signal. The amplified difference between these signals is
used to set Q2’s bias, and hence, Q1’s channel current.
This forces Q1’s VGS to whatever voltage is required to
matchthecircuit’sinputandoutputpotentials.The2000pF
capacitor at A1 provides stable loop compensation. The
RC network in A1’s output prevents it from seeing high
speed edges coupled through Q2’s collector-base junc-
tion. A2’soutputisalsofedbacktotheshieldaroundQ1’s
gate lead, bootstrapping the circuit’s effective input ca-
pacitance down to less than 1pF.
15pF
10k
15V
0.18Ω
+
1k
Q3
22µF
33Ω
68pF
2N3906
10k
Q1
MJE2955
INPUT
–
+
OUTPUT
LT1056
LT1010
100Ω
100Ω
Gain-Trimmable Wideband FET Amplifier
Q2
MJE3055
A potential difficulty with the previous circuit is that the
gain is not quite unity. The figure labeled A on the next
page maintains high speed and low bias while achieving
a true unity-gain transfer function.
1k
Q4
33Ω
2N3904
1010 AI17
–15V
0.18Ω
22µF
+
HEAT SINK OUTPUT TRANSISTORS
This circuit is somewhat similar except that the Q2-Q3
stage takes gain. A2 DC stabilizes the input-output path
and A1 provides drive capability. Feedback is to Q2’s
emitter from A1’s output. The 1k adjustment allows the
gain to be precisely set to unity. With the LT1010, output
stage slew and full power bandwidth (1VP-P) are 100V/µs
and10MHzrespectively.–3dBbandwidthexceeds35MHz.
At A = 10 (e.g., 1k adjustment set at 50Ω), full power
bandwidth stays at 10MHz while the –3dB point falls to
22MHz.
Wideband FET Input Stabilized Buffer
The figure below shows a highly stable unity-gain buffer
with good speed and high input impedance. Q1 and Q2
constitute a simple, high speed FET input buffer. Q1
functions as a source follower with the Q2 current source
loadsettingthedrain-sourcechannelcurrent.TheLT1010
buffer provides output drive capability for cables or
whatever load is required. Normally, this open-loop con-
figuration would be quite drifty because there is no DC
feedback. The LTC®1050 contributes this function to
stabilize the circuit. It does this by comparing the filtered
circuit output to a similarly filtered version of the input
With the optional discrete stage, slew exceeds 1000V/µs
and full power bandwidth (1VP-P) is 18MHz. –3dB band-
width is 58MHz. At A = 10, full power is available to
10MHz, with the –3dB point at 36MHz.
1010fc
13
LT1010
W U U
U
APPLICATIO S I FOR ATIO
Figures A and B show response with both output stages.
The LT1010 is used in Figure A (Trace A = input, Trace B
= output). Figure B uses the discrete stage and is slightly
faster. Either stage provides more than adequate perfor-
mance for driving video cable or data converters and the
LT1012 maintains DC stability under all conditions.
Thermal Considerations for the MiniDIP Package
The miniDIP package requires special thermal consider-
ationssinceitisnotdesignedtodissipatemuchpower. Be
aware that for applications requiring large output cur-
rents, another package should be used.
Gain-Trimmable Wideband FET Amplifier
15V
10pF
1k
470Ω
Q3
2N3906
Q1
2N5486
INPUT
15V
Q2
2N3904
A
B
A2
LT1010
OUTPUT
0.01µF
3k
1k
2N3904
1k
GAIN
ADJ
3Ω
3Ω
A
B
10M
10k
2k
300Ω 50Ω 5.6k
3k
10M
2N3906
0.1µF
0.1µF
+
–15V
3k
A1
LT1012
1k
–
–15V
0.002µF
1010 AI19
(A)
(B)
A = 0.2V/DIV
B = 0.2V/DIV
A = 0.2V/DIV
B = 0.2V/DIV
1010 AI20
1010 AI21
10ns/DIV
10ns/DIV
Figure A. Waveforms Using LT1010
Figure B. Waveforms Using Discrete Stage
1010fc
14
LT1010
W U U
APPLICATIO S I FOR ATIO
U
Typical thermal calculations for the miniDIP package are
to be dissipated, resulting in another (0.130W)
(0.130°C/W) = 16.9°C rise in junction temperature to
89°C + 16.9°C = 105.9°C.
detailed in the following paragraphs.
For 4.8mA supply current (typical at 50°C, 30V supply
voltage—see supply current graphs) to the LT1010 at
±15V, PD = power dissipated in the part is equal to:
Caution: This exceeds the maximum operating tempera-
ture of the device.
(30V)(0.0048A) = 0.144W
The rise in junction is then:
Thermal Resistance of DFN Package
For surface mount devices, heat sinking is accomplished
by using the heat spreading capabilities of the PC board
and its copper traces. Copper board stiffeners and plated
through-holes can also be used to spread the heat gener-
ated by power devices.
(0.144W)(130°C/W—This is θJA for the N package)
= 18.7°C.
This means that the junction temperature in 50°C ambient
air without driving any current into a load is:
The following table lists thermal resistance for several
different board sizes and copper areas. All measurements
were taken in still air on 3/32" FR-4 board with one ounce
copper.
18.7°C + 50°C = 68.7°C
Using the LT1010 to drive 8V DC into a 200Ω load using
±15V power supplies dissipates PD in the LT1010 where:
Table 1. DFN Measured Thermal Resistance
V+ – VOUT VOUT
COPPER AREA
(
)
)
(
THERMAL RESISTANCE
PD =
TOPSIDE
2500 sq mm
1000 sq mm
225 sq mm
100 sq mm
BACKSIDE
2500 sq mm
2500 sq mm
2500 sq mm
2500 sq mm
BOARD AREA
2500 sq mm
2500 sq mm
2500 sq mm
2500 sq mm
(JUNCTION-TO-AMBIENT)
RL
40°C/W
15V – 8V 8V
(
)(
)
45°C/W
=
= 0.280W
50°C/W
200Ω
62°C/W
This causes the LT1010 junction temperature to rise
another (0.280W)(0.130°C/W) = 36.4°C.
For the DFN package, the thermal resistance junction-to-
case(θJC),measuredattheexposedpadonthebackofthe
die, is 16°C/W.
This heats the junction to 68.7°C + 36.4°C = 105.1°C.
Caution: This exceeds the maximum operating tempera-
ture of the device.
Continuous operation at the maximum supply voltage and
maximum load current is not practical due to thermal
limitations. Transient operation at the maximum supply is
possible. The approximate thermal time constant for a
2500sq mm 3/32" FR-4 board with maximum topside and
backsideareaforoneouncecopperis3seconds.Thistime
constant will increase as more thermal mass is added (i.e.
vias, larger board, and other components).
An example of 1MHz operation further shows the limita-
tions of the N (or miniDIP) package. For ±15V operation:
PD at IL = 0 at 1MHz* = (10mA)(30V) = 0.30W
This power dissipation causes the junction to heat from
50°C (ambient in this example) to 50°C + (0.3W)
(130°C/W) = 89°C. Driving 2VRMS of 1MHz signal into a
200Ω load causes an additional
For an application with transient high power peaks, aver-
age power dissipation can be used for junction tempera-
turecalculationsaslongasthepulseperiodissignificantly
less than the thermal time constant of the device and
board.
⎛
⎞
2V
200Ω
PD =
• 15 – 2 = 0.130W
(
)
⎜
⎟
⎝
⎠
*See Supply Current vs Frequency graph.
1010fc
15
LT1010
W
W
SCHE ATIC DIAGRA
(Excluding protection circuits)
R6
15Ω
+
V
R10
200Ω
R7
300Ω
Q11
Q18
R5
1.5k
BIAS
Q17
Q19
R2
1k
R3
1k
R4
1k
R11
Q5
Q2
200Ω
C1
Q20
R14
30pF
Q6
Q7
R12
3k
Q8
Q21
7Ω
OUTPUT
INPUT
Q3
Q12
R8
1k
Q15
R13
200Ω
Q4
Q13
Q22
R1
4k
R9
4k
Q1
Q9
Q10
Q14
Q16
–
V
1010 SD
U U
W
DEFI ITIO OF TER S
Output Offset Voltage: The output voltage measured with
Saturation Resistance: The ratio of the change in output
saturation voltage to the change in current producing it,
going from no load to full load.*
the input grounded (split supply operation).
Input Bias Current: The current out of the input terminal.
Slew Rate: The average time rate of change of output
voltage over the specified output range with an input step
between the specified limits.
Large-Signal Voltage Gain: The ratio of the output volt-
age change to the input voltage change over the specified
input voltage range.*
Bias Terminal Voltage: The voltage between the bias
Output Resistance: The ratio of the change in output
voltage to the change in load current producing it.*
terminal and V+.
Supply Current: The current at either supply terminal with
no output loading.
Output Saturation Voltage: The voltage between the out-
put and the supply rail at the limit of the output swing
toward that rail.
*Pulse measurements (~1ms) as required to minimize thermal effects.
Saturation Offset Voltage: The output saturation voltage
with no load.
1010fc
16
LT1010
U
PACKAGE DESCRIPTIO
DD Package
8-Lead Plastic DFN (3mm × 3mm)
(Reference LTC DWG # 05-08-1698)
0.675 ±0.05
3.5 ±0.05
2.15 ±0.05 (2 SIDES)
1.65 ±0.05
PACKAGE
OUTLINE
0.25 ± 0.05
0.50
BSC
2.38 ±0.05
(2 SIDES)
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
R = 0.115
0.38 ± 0.10
TYP
5
8
3.00 ±0.10
(4 SIDES)
1.65 ± 0.10
(2 SIDES)
PIN 1
TOP MARK
(NOTE 6)
(DD) DFN 1203
4
1
0.25 ± 0.05
0.75 ±0.05
0.200 REF
0.50 BSC
2.38 ±0.10
(2 SIDES)
0.00 – 0.05
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-1)
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON TOP AND BOTTOM OF PACKAGE
1010fc
17
LT1010
U
PACKAGE DESCRIPTIO
N8 Package
8-Lead PDIP (Narrow .300 Inch)
(Reference LTC DWG # 05-08-1510)
.400*
(10.160)
MAX
8
7
6
5
4
.255 ± .015*
(6.477 ± 0.381)
1
2
3
.130 ± .005
.300 – .325
.045 – .065
(3.302 ± 0.127)
(1.143 – 1.651)
(7.620 – 8.255)
.065
(1.651)
TYP
.008 – .015
(0.203 – 0.381)
.120
.020
(0.508)
MIN
(3.048)
MIN
+.035
.325
–.015
.018 ± .003
(0.457 ± 0.076)
.100
(2.54)
BSC
+0.889
8.255
(
)
N8 1002
–0.381
NOTE:
INCHES
1. DIMENSIONS ARE
MILLIMETERS
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .010 INCH (0.254mm)
1010fc
18
LT1010
U
PACKAGE DESCRIPTIO
T Package
5-Lead Plastic TO-220 (Standard)
(Reference LTC DWG # 05-08-1421)
.165 – .180
(4.191 – 4.572)
.147 – .155
(3.734 – 3.937)
DIA
.390 – .415
(9.906 – 10.541)
.045 – .055
(1.143 – 1.397)
.230 – .270
(5.842 – 6.858)
.570 – .620
(14.478 – 15.748)
.620
(15.75)
TYP
.460 – .500
(11.684 – 12.700)
.330 – .370
(8.382 – 9.398)
.700 – .728
(17.78 – 18.491)
.095 – .115
(2.413 – 2.921)
SEATING PLANE
.152 – .202
(3.861 – 5.131)
.155 – .195*
(3.937 – 4.953)
.260 – .320
(6.60 – 8.13)
.013 – .023
(0.330 – 0.584)
.067
BSC
.135 – .165
(3.429 – 4.191)
.028 – .038
(0.711 – 0.965)
(1.70)
* MEASURED AT THE SEATING PLANE
T5 (TO-220) 0801
1010fc
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen-
tationthattheinterconnectionofitscircuitsasdescribedhereinwillnotinfringeonexistingpatentrights.
19
LT1010
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT1206
250mA, 60MHz Current Feedback Amplifier
1.1A, 35MHz Current Feedback Amplifier
Dual 500mA, 50MHz CFA
900V/µs, Excellent Video Characteristics
900V/µs Slew Rate, Stable with Large Capacitive Loads
LT1210
LT1795
500mA I
ADSL Driver
OUT
LT1886
Dual 700MHz, 200mA Op Amp
DSL Driver
1010fc
LT/LWI 0806 REV C • PRINTED IN THE USA
LinearTechnology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
20
●
●
(408) 432-1900 FAX: (408) 434-0507 www.linear.com
© LINEAR TECHNOLOGY CORPORATION 1991
相关型号:
LT1011ACH#PBF
IC COMPARATOR, 1000 uV OFFSET-MAX, 150 ns RESPONSE TIME, MBCY8, METAL CAN, LEAD FREE, TO-5, 8 PIN, Comparator
Linear
LT1011ACH#TR
IC COMPARATOR, 1000 uV OFFSET-MAX, 150 ns RESPONSE TIME, MBCY8, METAL CAN, TO-5, 8 PIN, Comparator
Linear
LT1011ACN8#PBF
LT1011/LT1011A - Voltage Comparator; Package: PDIP; Pins: 8; Temperature Range: 0°C to 70°C
Linear
©2020 ICPDF网 联系我们和版权申明