MT90823AP [ZARLINK]
3V Large Digital Switch; 3V大型数字交换机型号: | MT90823AP |
厂家: | ZARLINK SEMICONDUCTOR INC |
描述: | 3V Large Digital Switch |
文件: | 总46页 (文件大小:664K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MT90823
3 V Large Digital Switch
Data Sheet
July 2005
Features
•
2,048 × 2,048 channel non-blocking switching at
Ordering Information
8.192 Mb/s
MT90823AP
MT90823AL
MT90823AB
MT90823AG
84 Pin PLCC
100 Pin MQFP
100 Pin LQFP
120 Pin BGA
Tubes
Trays
Trays
Trays
Trays
Tubes
Trays
•
Per-channel variable or constant throughput
delay
Automatic identification of ST-BUS/GCI interfaces
•
•
MT90823AB1 100 Pin LQFP*
MT90823AP1 84 Pin PLCC*
Accept ST-BUS streams of 2.048, 4.096 or
8.192 Mb/s
MT90823AL1
100 Pin MQFP*
*Pb Free Matte Tin
•
•
•
•
•
Automatic frame offset delay measurement
Per-stream frame delay offset programming
Per-channel high impedance output control
Per-channel message mode
-40°C to +85°C
Applications
•
•
•
•
•
•
Medium and large switching platforms
CTI application
Voice/data multiplexer
Control interface compatible to Motorola non-
multiplexed CPUs
•
•
Connection memory block programming
3.3 V local I/O with 5 V tolerant inputs and TTL-
compatible outputs
Digital cross connects
ST-BUS/GCI interface functions
Support IEEE 802.9a standard
•
IEEE-1149.1 (JTAG) Test Port
V
V
SS
ODE
TMS
TDI TDO TCK TRST
IC
RESET
DD
Test Port
Loopback
STo0
STo1
STo2
STo3
STo4
STo5
STo6
STo7
STo8
STo9
STo10
STo11
STo12
STo13
STo14
STo15
STi0
STi1
STi2
Serial
to
Parallel
to
STi3
STi4
Output
STi5
Parallel
Multiple Buffer
Data Memory
STi6
MUX
Serial
STi7
Converter
STi8
Converter
STi9
STi10
STi11
STi12
STi13
STi14
STi15
Connection
Memory
Internal
Registers
Timing
Unit
Microprocessor Interface
CLK F0i FE/ WFPS
HCLK
AS/ IM DS/
CS R/W
/WR
D15-D8/ CSTo
A7-A0 DTA
ALE
RD
AD7-AD0
Figure 1 - Functional Block Diagram
1
Zarlink Semiconductor Inc.
Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc.
Copyright 2003-2005, Zarlink Semiconductor Inc. All Rights Reserved.
MT90823
Data Sheet
Description
The MT90823 Large Digital Switch has a non-blocking switch capacity of: 2,048 x 2,048 channels at a serial bit rate
of 8.192 Mb/s; 1,024 x 1,024 channels at 4.096 Mb/s; and 512 x 512 channels at 2.048 Mb/s. The device has many
features that are programmable on a per stream or per channel basis, including message mode, input offset delay
and high impedance output control.
Per stream input delay control is particularly useful for managing large multi-chip switches that transport both voice
channel and concatenated data channels.
In addition, the input stream can be individually calibrated for input frame offset using a dedicated pin.
2
Zarlink Semiconductor Inc.
MT90823
Data Sheet
10
8
6
4
2
84
82
80
78
76
STi0
STi1
CSTo
DTA
D15
D14
D13
D12
D11
D10
D9
13
73
STi2
STi3
15
17
19
21
23
25
27
29
31
71
69
67
65
63
61
59
57
55
STi4
STi5
STi6
STi7
STi8
STi9
D8
84 PIN PLCC
STi10
STi11
STi12
STi13
STi14
STi15
F0i
VSS
VDD
AD7
AD6
AD5
AD4
AD3
AD2
AD1
AD0
VSS
FE/HCLK
VSS
CLK
VDD
34
36
38
40
42
44
46
48
50
52
80
82
78
76
74
72
70
68
66
64
62
60
58
56
54
52
50
48
46
44
42
40
38
36
34
32
DTA
D15
D14
D13
D12
D11
D10
D9
STi0
STi1
STi2
84
86
88
90
92
94
96
STi3
STi4
STi5
STi6
STi7
D8
STi8
100 PIN MQFP
(14mm x 20mm x 2.75mm)
VSS
VDD
AD7
AD6
AD5
AD4
AD3
AD2
AD1
AD0
VSS
STi9
STi10
STi11
STi12
STi13
STi14
STi15
F0i
98
99
FE/HCLK
VSS
CLK
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
Figure 2 - PLCC and MQFP Pin Connections
3
Zarlink Semiconductor Inc.
MT90823
Data Sheet
1
2
3
4
5
6
7
8
9
10
11
12
13
1
A
VSS VSS STo14 STo12STo10 STo9 STo7 STo5 STo4 STo2 STo0 VSS VSS
VSS VSS STo15 STo13STo11 STo8 VSS STo6 STo3 STo1 ODE VSS VSS
B
C
D
E
F
STi1 VSS VDD VSS VDD VSS VDD VSS VDD VSS DTA
STi0
STi2
STi4
STi6
STi8
STi10
CSTo
D15
D13
D11
D9
STi3 VDD
STi5 VSS
STi7 VDD
STi9 VSS
STi11 VDD
D14
VDD
VSS D12
VDD D10
VSS D8
TOP VIEW
PBGA
(23mm x 23mm x 2.13mm)
(Ball Pitch = 1.5mm)
G
H
J
VDD AD6
VSS AD4
VDD AD2
AD7
AD5
AD3
AD1
VSS
IM
STi12 STi13 VSS
STi15 VDD
K
L
STi14
FE/HCLKVSS VDD VSS VDD VSS VDD VSS VDD
AD0
F0i
VSS VSS TDI TCK IC
CLK TMS TDO TRST RESETA0
VSS
A6 R/W/RWAS/ALEVSS
A5 A7 DS/RD CS
M
N
WFPSA1
A2
A4
A3
1
- A1 corner is identified by metallized markings.
74
72
70
68
66
64
62
60
58
56
54
52
76
NC
50
NC
NC
NC
STi0
78
80
CSTo
DTA
D15
D14
D13
D12
D11
D10
D9
48
46
STi1
STi2
STi3
82
84
86
88
90
STi4
44
42
STi5
STi6
STi7
100 PIN LQFP
STi8
40
38
36
34
D8
STi9
(14mm x 14mm x 1.4mm)
(Pin Pitch = 0.50mm)
STi10
STi11
STi12
STi13
STi14
STi15
F0i
VSS
VDD
AD7
AD6
AD5
AD4
AD3
AD2
AD1
AD0
VSS
NC
92
94
32
30
28
26
FE/HCLK
VSS
96
CLK
98
VDD
NC
100
NC
NC
2
4
6
8
10
12
14
16
18
20
22
24
Figure 3 - PBGA and LQFP Pin Connections
4
Zarlink Semiconductor Inc.
MT90823
Data Sheet
Pin Description
Pin #
100
Name
Description
84
100
120
PLCC MQFP LQFP
BGA
1, 11, 31, 41,
30, 54 56, 66,
64, 75 76, 99
28,
38,
53,
63,
73,
96
A1,A2,A12,A13,
B1,B2,B7,B12,
B13,C3,C5,C7,
C9,C11,E3,E11
G3,G11,J3,J11,
L3,L5,L7,L9,L11,
M1,M2,M12,M13
VSS
Ground.
2, 32, 5, 40,
37,
C4,C6,C8,C10,
VDD
+3.3 Volt Power Supply.
63
67
64,98 D3,D11,F3,F11,
H3,H11,K3,K11,
L4,L6,L8,L10
3 - 10 68-75
65 -
72
B6,A6,A5,B5,A4, STo8 - 15 ST-BUS Output 8 to 15 (5 V Tolerant Three-state
B4,A3,B3
Outputs): Serial data Output stream. These streams
may have data rates of 2.048, 4.096 or 8.192 Mb/s,
depending upon the value programmed at bits DR0 - 1
in the IMS register.
12 -
27
81-96
97
78 - C1,C2,D1,D2,E1, STi0 - 15 ST-BUS Input 0 to 15 (5 V Tolerant Inputs): Serial
93
E2,F1,F2,G1,G2,
H1,H2,J1,J2,K1,
K2
data input stream. These streams may have data rates
of 2.048, 4.096 or 8.192 Mb/s, depending upon the
value programmed at bits DR0 - 1 in the IMS register.
28
94
L1
F0i
Frame Pulse (5 V Tolerant Input): When the WFPS
pin is low, this input accepts and automatically
identifies frame synchronization signals formatted
according to ST-BUS and GCI specifications. When the
WFPS pin is high, this pin accepts a negative frame
pulse which conforms to WFPS formats.
29
31
98
95
97
L2
FE/HCLK Frame Evaluation / HCLK Clock (5 V Tolerant
Input): When the WFPS pin is low, this pin is the frame
measurement input. When the WFPS pin is high, the
HCLK (4.096MHz clock) is required for frame
alignment in the wide frame pulse (WFP) mode.
100
N1
CLK
Clock (5 V Tolerant Input): Serial clock for shifting
data in/out on the serial streams (STi/o 0 - 15).
Depending upon the value programmed at bits DR0 - 1
in the IMS register, this input accepts a 4.096, 8.192 or
16.384 MHz clock.
33
34
6
7
3
4
N2
M3
TMS
TDI
Test Mode Select (3.3 V Input with internal pull-up):
JTAG signal that controls the TAP controller state
transitions.
Test Serial Data In (3.3 V Tolerant Input with internal
pull-up): JTAG serial test instructions and data are
shifted in on this pin.
5
Zarlink Semiconductor Inc.
MT90823
Data Sheet
Pin Description (continued)
Pin #
Name
Description
84
100
100
120
PLCC MQFP LQFP
BGA
35
8
5
N3
TDO
Test Serial Data Out (3.3 V Output): JTAG serial data
is output on this pin on the falling edge of TCK. This pin
is held in high impedance state when JTAG scan is not
enabled.
36
37
9
6
7
M4
N4
TCK
Test Clock (5 V Tolerant Input): Provides the clock to
the JTAG test logic.
10
TRST
Test Reset (3.3 V Input with internal pull-up):
Asynchronously initializes the JTAG TAP controller by
putting it in the Test-Logic-Reset state. This pin should
be pulsed low on power-up, or held low, to ensure that
the MT90823 is in the normal functional mode.
38
39
11
12
8
9
M5
N5
IC
Internal Connection (3.3 V Input with internal pull-
down): Connect to VSS for normal operation. This pin
must be low for the MT90823 to function normally and
to comply with IEEE 1149 (JTAG) boundary scan
requirements.
RESET Device Reset (5 V Tolerant Input): This input (active
LOW) puts the MT90823 in its reset state to clear the
device internal counters, registers and bring STo0 - 15
and microport data outputs to a high impedance state.
The time constant for a power up reset circuit must be a
minimum of five times the rise time of the power supply.
In normal operation, the RESET pin must be held low
for a minimum of 100 nsec to reset the device.
40
13
14-21
22
10
M6
WFPS
Wide Frame Pulse Select (5 V Tolerant Input): When
1, enables the wide frame pulse (WFP) Frame
Alignment interface. When 0, the device operates in
ST-BUS/GCI mode.
41 -
48
11 -
18
N6,M7,N7,N8,
M8,N9,M9,N10
A0 - A7 Address 0 - 7 (5 V Tolerant Input): When non-
multiplexed CPU bus operation is selected, these lines
provide the A0 - A7 address lines to the internal
memories.
49
19
N11
DS/RD Data Strobe / Read (5 V Tolerant Input): For Motorola
multiplexed bus operation, this input is DS. This active
high DS input works in conjunction with CS to enable
the read and write operations.
For Motorola non-multiplexed CPU bus operation, this
input is DS. This active low input works in conjunction
with CS to enable the read and write operations.
For multiplexed bus operation, this input is RD. This
active low input sets the data bus lines (AD0-AD7, D8-
D15) as outputs.
6
Zarlink Semiconductor Inc.
MT90823
Data Sheet
Pin Description (continued)
Pin #
Name
Description
84
100
100
120
PLCC MQFP LQFP
BGA
50
23
20
M10
R/W / WR Read/Write / Write (5 V Tolerant Input): In the cases
of Motorola non-multiplexed and multiplexed bus
operations, this input is R/W. This input controls the
direction of the data bus lines (AD0 - AD7, D8-D15)
during a microprocessor access.
For multiplexed bus operation, this input is WR. This
active low input is used with RD to control the data bus
(AD0 - 7) lines as inputs.
51
52
24
25
21
22
N12
M11
CS
Chip Select (5 V Tolerant Input): Active low input
used by a microprocessor to activate the
microprocessor port of MT90823.
AS/ALE Address Strobe or Latch Enable (5 V Tolerant
Input): This input is used if multiplexed bus operation
is selected via the IM input pin. For Motorola non-
multiplexed bus operation, connect this pin to ground.
53
26
23
N13
IM
CPU Interface Mode (5 V Tolerant Input): When IM is
high, the microprocessor port is in the multiplexed
mode. When IM is low, the microprocessor port is in
non-multiplexed mode.
55 -
62
32-39
29 -
36
L12,L13,K12,
K13,J12,J13,
H12,H13
AD0 - 7 Address/Data Bus 0 to 7 (5 V Tolerant I/O): These
pins are the eight least significant data bits of the
microprocessor port. In multiplexed mode, these pins
are also the input address bits of the microprocessor
port.
65 -
72
42-49
50
39 -
46
G12,G13,F12,
F13,E12,E13,
D12,D13
D8 - 15 Data Bus 8-15 (5 V Tolerant I/O): These pins are the
eight most significant data bits of the microprocessor
port.
73
47
C12
DTA
Data Transfer Acknowledgement (5 V tolerant
Three-state Output): Indicates that a data bus transfer
is complete. When the bus cycle ends, this pin drives
HIGH and then tri-states, allowing for faster bus cycles
with a weaker pull-up resistor. A pull-up resistor is
required to hold a HIGH level when the pin is tri-stated.
74
55
48
C13
CSTo
Control Output (5 V Tolerant Output). This is a
4.096, 8.192 or 16.384 Mb/s output containing 512,
1024 or 2048 bits per frame respectively. The level of
each bit is determined by the CSTo bit in the
connection memory. See External Drive Control
Section.
7
Zarlink Semiconductor Inc.
MT90823
Data Sheet
Pin Description (continued)
Pin #
Name
Description
84
100
100
120
PLCC MQFP LQFP
BGA
76
57
54
B11
ODE
Output Drive Enable (5 V Tolerant Input): This is the
output enable control for the STo0-15 serial outputs.
When ODE input is low and the OSB bit of the IMS
register is low, STo0-15 are in a high impedance state.
If this input is high, the STo0-15 output drivers are
enabled. However, each channel may still be put into a
high impedance state by using the per channel control
bit in the connection memory.
77 -
84
58-65
55 -
62
A11,B10,A10,B9, STo0 - 7 Data Stream Output 0 to 7 (5 V Tolerant Three-state
A9,A8,B8,A7
Outputs): Serial data Output stream. These streams
have selectable data rates of 2.048, 4.096 or
8.192 Mb/s.
-
1 - 4,
27 -
30,
1 - 2,
24 -
27,
NC
No connection.
51 -
54
49 -
52,
77 -
80
74 -
77,
99 -
100
Device Overview
The MT90823 Large Digital Switch is capable of switching up to 2,048 × 2,048 channels. The MT90823 is designed
to switch 64 kb/s PCM or N x 64 kb/s data. The device maintains frame integrity in data applications and minimum
throughput delay for voice applications on a per channel basis.
The serial input streams of the MT90823 can have a bit rate of 2.048, 4.096 or 8.192 Mbit/s and are arranged in
125 µs wide frames, which contain 32, 64 or 128 channels, respectively. The data rates on input and output
streams are identical.
By using Zarllink’s message mode capability, the microprocessor can access input and output time-slots on a per
channel basis. This feature is useful for transferring control and status information for external circuits or other ST-
BUS devices. The MT90823 automatically identifies the polarity of the frame synchronization input signal and
configures its serial streams to be compatible to either ST-BUS or GCI formats.
Two different microprocessor bus interfaces can be selected through the Input Mode pin (IM): Non-multiplexed or
Multiplexed. These interfaces provide compatibility with multiplexed and Motorola multiplexed/non-multiplexed
buses.
The frame offset calibration function allows users to measure the frame offset delay using a frame evaluation pin
(FE). The input offset delay can be programmed for individual streams using internal frame input offset registers,
see Table 11.
The internal loopback allows the ST-BUS output data to be looped around to the ST-BUS inputs for diagnostic
purposes.
8
Zarlink Semiconductor Inc.
MT90823
Data Sheet
Functional Description
A functional Block Diagram of the MT90823 is shown in Figure 1.
Data and Connection Memory
For all data rates, the received serial data is converted to parallel format by internal serial-to-parallel converters and
stored sequentially in the data memory. Depending upon the selected operation programmed in the interface mode
select (IMS) register, the useable data memory may be as large as 2,048 bytes. The sequential addressing of the
data memory is performed by an internal counter, which is reset by the input 8 kHz frame pulse (F0i) to mark the
frame boundaries of the incoming serial data streams.
Data to be output on the serial streams may come from either the data memory or connection memory. Locations in
the connection memory are associated with particular ST-BUS output channels. When a channel is due to be
transmitted on an ST-BUS output, the data for this channel can be switched either from an ST-BUS input in
connection mode, or from the lower half of the connection memory in message mode. Data destined for a particular
channel on a serial output stream is read from the data memory or connection memory during the previous channel
time-slot. This allows enough time for memory access and parallel-to-serial conversion.
Connection and Message Modes
In the connection mode, the addresses of the input source data for all output channels are stored in the connection
memory. The connection memory is mapped in such a way that each location corresponds to an output channel on
the output streams. For details on the use of the source address data (CAB and SAB bits), see Table 13 and Table
14. Once the source address bits are programmed by the microprocessor, the contents of the data memory at the
selected address are transferred to the parallel-to-serial converters and then onto an ST-BUS output stream.
By having several output channels connected to the same input source channel, data can be broadcasted from one
input channel to several output channels.
In message mode, the microprocessor writes data to the connection memory locations corresponding to the output
stream and channel number. The lower half (8 least significant bits) of the connection memory content is
transferred directly to the parallel-to-serial converter. This data will be output on the ST-BUS streams in every frame
until the data is changed by the microprocessor.
The five most significant bits of the connection memory controls the following for an output channel: message or
connection mode; constant or variable delay; enables/tristate the ST-BUS output drivers; and, enables/disable the
loopback function. In addition, one of these bits allows the user to control the CSTo output.
If an output channel is set to a high-impedance state through the connection memory, the ST-BUS output
will be in a high impedance state for the duration of that channel. In addition to the per-channel control, all channels
on the ST-BUS outputs can be placed in a high impedance state by either pulling the ODE input pin low or
programming the output standby (OSB) bit in the interface mode selection register to low. This action overrides the
individual per-channel programming by the connection memory bits.
The connection memory data can be accessed via the microprocessor interface through the D0 to D15 pins. The
addressing of the device internal registers, data and connection memories is performed through the address input
pins and the Memory Select (MS) bit of the control register. For details on device addressing, see Software Control
and Control Register bits description (Tables 4, 6 and 7).
Serial Data Interface Timing
The master clock frequency must always be twice the data rate. The master clock (CLK) must be either at 4.096,
8.192 or 16.384 MHz for serial data rate of 2.048, 4.096 or 8.192 Mb/s respectively. The input and output stream
data rates will always be identical.
9
Zarlink Semiconductor Inc.
MT90823
Data Sheet
The MT90823 provides two different interface timing modes controlled by the WFPS pin. If the WFPS pin is low, the
MT90823 is in ST-BUS/GCI mode. If the WFPS pin is high, the MT90823 is in the wide frame pulse (WFP) frame
alignment mode.
In ST-BUS/GCI mode, the input 8 kHz frame pulse can be in either ST-BUS or GCI format. The MT90823
automatically detects the presence of an input frame pulse and identifies it as either ST-BUS or GCI. In ST-BUS
format, every second falling edge of the master clock marks a bit boundary and the data is clocked in on the rising
edge of CLK, three quarters of the way into the bit cell, see Figure 11. In GCI format, every second rising edge of
the master clock marks the bit boundary and data is clocked in on the falling edge of CLK at three quarters of the
way into the bit cell, see Figure 12.
Wide Frame Pulse (WFP) Frame Alignment Timing
When the device is in WFP frame alignment mode, the CLK input must be at 16.384 MHz, the FE/HCLK input is
4.096 MHz and the 8 kHz frame pulse is in ST-BUS format. The timing relationship between CLK, HCLK and the
frame pulse is defined in Figure 13.
When the WFPS pin is high, the frame alignment evaluation feature is disabled, but the frame input offset registers
may still be programmed to compensate for the varying frame delays on the serial input streams.
Switching Configurations
The MT90823 maximum non-blocking switching configurations is determined by the data rates selected for the
serial inputs and outputs. The switching configuration is selected by two DR bits in the IMS register. See Table 8 nd
Table 9.
2.048 Mb/s Serial Links (DR0=0, DR1=0)
When the 2.048 Mb/s data rate is selected, the device is configured with 16-input/16-output data streams each
having 32 64 kb/s channels. This mode requires a CLK of 4.094 MHz and allows a maximum non-blocking
capacity of 512 x 512 channels.
4.096 Mb/s Serial Links (DR0=1, DR1=0)
When the 4.096 Mb/s data rate is selected, the device is configured with 16-input/16-output data streams each
having 64 64 kb/s channels. This mode requires a CLK of 8.192 MHz and allows a maximum non-blocking
capacity of 1,024 x 1,024 channels.
8.192 Mb/s Serial Links (DR0=0, DR1=1)
When the 8.192 Mb/s data rate is selected, the device is configured with 16-input/16-output data streams each
having 128 64 kb/s channels. This mode requires a CLK of 16.384 MHz and allows a maximum non-blocking
capacity of 2,048 x 2,048 channels. Table 1 summarizes the switching configurations and the relationship between
different serial data rates and the master clock frequencies.
10
Zarlink Semiconductor Inc.
MT90823
Data Sheet
Serial Interface
Data Rate
Master Clock
Required (MHz)
Matrix Channel
Capacity
2 Mb/s
4 Mb/s
8 Mb/s
4.096
8.192
512 x 512
1,024 x 1,024
2,048 x 2,048
16.384
Table 1 - Switching Configuration
Input Frame Offset Selection
Input frame offset selection allows the channel alignment of individual input streams to be offset with respect to the
output stream channel alignment (i.e., F0i). This feature is useful in compensating for variable path delays caused
by serial backplanes of variable lengths, which may be implemented in large centralized and distributed switching
systems.
Each input stream can have its own delay offset value by programming the frame input offset (FOR) registers.
Possible adjustment can range up to +4 master clock (CLK) periods forward with resolution of 1/2 clock period. The
output frame offset cannot be offset or adjusted. See Figure 4, Table 11 and Table 12 for delay offset programming.
Serial Input Frame Alignment Evaluation
The MT90823 provides the frame evaluation (FE) input to determine different data input delays with respect to the
frame pulse F0i.
A measurement cycle is started by setting the start frame evaluation (SFE) bit low for at least one frame. Then the
evaluation starts when the SFE bit in the IMS register is changed from low to high. Two frames later, the complete
frame evaluation (CFE) bit of the frame alignment register (FAR) changes from low to high. This signals that a valid
offset measurement is ready to be read from bits 0 to 11 of the FAR register. The SFE bit must be set to zero before
starting a new measurement cycle.
In ST-BUS mode, the falling edge of the frame measurement signal (FE) is evaluated against the falling edge of the
ST-BUS frame pulse. In GCI mode, the rising edge of FE is evaluated against the rising edge of the GCI frame
pulse. See Table 10 and Figure 3 for the description of the frame alignment register.
This feature is not available when the WFP Frame Alignment mode is enabled (i.e., when the WFPS pin is
connected to VDD).
Memory Block Programming
The MT90823 provides users with the capability of initializing the entire connection memory block in two frames.
Bits 11 to 15 of every connection memory location will be programmed with the pattern stored in bits 5 to 9 of the
IMS register.
The block programming mode is enabled by setting the memory block program (MBP) bit of the control register
high. When the block programming enable (BPE) bit of the IMS register is set to high, the block programming data
will be loaded into the bits 11 to 15 of every connection memory location. The other connection memory bits (bit 0 to
bit 10) are loaded with zeros. When the memory block programming is complete, the device resets the BPE bit to
zero.
Loopback Control
The loopback control (LPBK) bit of each connection memory location allows the ST-BUS output data to be looped
backed internally to the ST-BUS input for diagnostic purposes.
11
Zarlink Semiconductor Inc.
MT90823
Data Sheet
If the LPBK bit is high, the associated ST-BUS output channel data is internally looped back to the ST-BUS input
channel (i.e., data from STo n channel m will appear in STi n channel M). Note: when LPBK is activated in channel
m STo n+1 (for n even) or STo n-1 (for n odd), the data from channel m of STi n will be switched to channel m STo
n. The associated frame delay offset register must be set to zero for proper operation of the per-channel loopback
function. If the LPBK bit is low, the per-channel loopback feature is disabled and the device will function normally.
Delay Through the MT90823
The switching of information from the input serial streams to the output serial streams results in a throughput delay.
The device can be programmed to perform time-slot interchange functions with different throughput delay
capabilities on a per-channel basis. For voice application, select variable throughput delay to ensure minimum
delay between input and output data. In wideband data applications, select constant throughput delay to maintain
the frame integrity of the information through the switch.
The delay through the device varies according to the type of throughput delay selected in the V/C bit of the
connection memory.
Variable Delay Mode (V/C bit = 0)
The delay in this mode is dependent only on the combination of source and destination channels. It is independent
of input and output streams. The minimum delay achievable in the MT90823 is three time-slots. When the input
channel data is switched to the same output channel (channel n, frame p), it will be output in the following frame
(channel n, frame p+1). The same frame delay occurs if the input channel n is switched to output channel n+1 or
n+2. When input channel n is switched to output channel n+3, n+4,..., the new output data will appear in the same
frame. Table 2 shows the possible delays for the MT90823 in the variable delay mode.
Constant Delay Mode (V/C bit = 1)
In this mode, frame integrity is maintained in all switching configurations by using a multiple data memory buffer.
Input channel data written into the data memory buffers during frame n will be read out during frame n+2.
In the MT90823, the minimum throughput delay achievable in the constant delay mode is one frame. For example,
in 2 Mb/s mode, when input time-slot 31 is switched to output time-slot 0. The maximum delay of 94 time-slots
occurs when time-slot 0 in a frame is switched to time-slot 31 in the frame. See Table 3.
Microprocessor Interface
The MT90823 provides a parallel microprocessor interface for non-multiplexed or multiplexed bus structures. This
interface is compatible with Motorola non-multiplexed and multiplexed buses.
If the IM pin is low, the MT90823 microprocessor interface assumes Motorola non-multiplexed bus mode. If the IM
pin is high, the device micro- processor interface accepts two different timing modes (mode1 and mode2) which
allows direct connection to multiplexed microprocessors.
The microprocessor interface automatically identifies the type of microprocessor bus connected to the MT90823.
This circuit uses the level of the DS/RD input pin at the rising edge of AS/ALE to identify the appropriate bus timing
connected to the MT90823. If DS/RD is high at the falling edge of AS/ALE, then the mode 1 multiplexed timing is
selected. If DS/RD is low at the falling edge of AS/ALE, then the mode 2 multiplexed bus timing is selected.
12
Zarlink Semiconductor Inc.
MT90823
Data Sheet
Delay for Variable Throughput Delay Mode
(m - output channel number)
Input Rate
(n - input channel number))
m < n
m = n, n+1, n+2
m > n+2
2.048 Mb/s
4.096 Mb/s
8.192 Mb/s
32 - (n-m) time-slots
64 - (n-m) time-slots
128 - (n-m) time-slots
m-n + 32 time-slots
m-n + 64 time-slots
m-n + 128 time-slots
m-n time-slots
m-n time-slots
m-n time-slots
Table 2 - Variable Throughput Delay Value
Delay for Constant Throughput Delay Mode
(m - output channel number)
Input Rate
(n - input channel number))
2.048 Mb/s
4.096 Mb/s
8.192 Mb/s
32 + (32 - n) + (m - 1) time-slots
64 + (64 - n) + (m- 1) time-slots
128 + (128 - n) + (m- 1) time-slots
Table 3 - Constant Throughput Delay Value
For multiplexed operation, the 8-bit data and address (AD0-AD7), 8-bit Data (D8-D15), Address strobe/Address
latch enable (AS/ALE), Data strobe/Read (DS/RD), Read/Write /Write (R/W / WR), Chip select (CS) and Data
transfer acknowledge (DTA) signals are required. See Figure 13 and Figure 14 for multiplexed parallel microport
timing.
For the Motorola non-multiplexed bus, the 16-bit data bus (AD0-AD7, D8-D15), 8-bit address bus (A0-A7) and 4
control lines (CS, DS, R/W and DTA) signals are required. See Figure 15 for Motorola non- multiplexed microport
timing.
The MT90823 microport provides access to the internal registers, connection and data memories. All locations
provide read/write access except for the data memory and the frame alignment register which are read only.
Memory Mapping
The address bus on the microprocessor interface selects the MT90823 internal registers and memory. If the A7
address input is low, then the control (CR), interface mode selection (IMS), frame alignment (FAR) and frame input
offset (FOR) registers are addressed by A6 to A0 as shown in Table 4.
If the A7 address input is high, then the remaining address input lines are used to select up to 128 memory
subsection locations. The number selected corresponds to the maximum number of channels per input or output
stream. The address input lines and the stream address bits (STA) of the control register allow access to the entire
data and connection memories.
The control and IMS registers together control all the major functions of the device. The IMS register should be
programmed immediately after system power-up to establish the desired switching configuration (see “Serial Data
Interface Timing” and “Switching Configurations” ).
The control register controls switching operations in the MT90823. It selects the internal memory locations that
specify the input and output channels selected for switching.
13
Zarlink Semiconductor Inc.
MT90823
Data Sheet
The data in the control register consists of the memory block programming bit (MBP), the memory select bit (MS)
and the stream address bits (STA). The memory block programming bit allows users to program the entire
connection memory block, (see “Memory Block Programming” ). The memory select bit controls the selection of the
connection memory or the data Memory. The stream address bits define an internal memory subsections
corresponding to input or output ST-BUS streams.
The data in the IMS register consists of block programming bits (BPD0-BPD4), block programming enable bit
(BPE), output standby bit (OSB), start frame evaluation bit (SFE) and data rate selection bits (DR0, DR1). The block
programming and the block programming enable bits allows users to program the entire connection memory, (see
Memory Block Programming section). If the ODE pin is low, the OSB bit enables (if high) or disables (if low) all ST-
BUS output drivers. If the ODE pin is high, the contents of the OSB bit is ignored and all ST-BUS output drivers are
enabled.
Connection Memory Control
The contents of the CSTo bit of each connection memory location are output on the CSTo pin once every frame.
The CSTo pin is a 4.096, 8.192 or 16.384 Mb/s output carrying 512, 1,024 or 2,048 bits respectively. If the CSTo bit
is set high, the corresponding bit on the CSTo output is transmitted high. If the CSTo bit is low, the corresponding bit
on the CSTo output is transmitted low. The contents of the CSTo bits of the connection memory are transmitted
sequentially via the CSTo pin and are synchronous with the data rates on the other ST-BUS streams.
The CSTo bit is output one channel before the corresponding channel on the ST-BUS. For example, in 2 Mb/s
mode, the contents of the CSTo bit in position 0 (STo0, CH0) of the connection memory is output on the first clock
cycle of channel 31 via CSTo pin. The contents of the CSTo bit in position 32 (STo1, CH0) of the connection
memory is output on the second clock cycle of channel 31 via CSTo pin.
When either the ODE pin or the OSB bit is high, the OE bit of each connection memory location enables (if high) or
disables (if low) the output drivers for an individual ST-BUS output stream and channel. Table 5 details this function.
The connection memory message channel (MC) bit (if high) enables message mode in the associated ST-BUS
output channel. When message mode is enabled, only the lower half (8 least significant bits) of the connection
memory is transferred to the ST-BUS outputs.
If the MC bit is low, the contents of the connection memory stream address bit (SAB) and channel address bit
(CAB) defines the source information (stream and channel) of the time-slot that will be switched to the output.
Bit V/C (Variable/Constant Delay) of each connection memory location allows the per-channel selection between
variable and constant throughput delay modes.
The loopback bit should be used for diagnostic purpose only; this bit should be set to zero for normal operation. If
all LPBK bits are set high for all connection memory locations, the associated ST-BUS output channel data is
internally looped back to the ST-BUS input channel (i.e., SToN channel m data loops back to STi N channel m).
14
Zarlink Semiconductor Inc.
MT90823
Data Sheet
A7
A6
A5
A4
A3
A2
A1
A0
Location
Control Register, CR
(Note 1)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
Interface Mode Selection Register, IMS
Frame Alignment Register, FAR
Frame Input Offset Register 0, FOR0
Frame Input Offset Register 1, FOR1
Frame Input Offset Register 2, FOR2
Frame Input Offset Register 3, FOR3
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
.
0
0
.
0
0
.
0
0
.
0
1
.
Ch 0
Ch 1
.
1
1
1
1
1
1
1
1
0
1
Ch 30
Ch 31
(Note 2)
(Note 3)
(Note 4)
1
1
1
1
1
0
0
0
0
0
1
1
1
1
1
0
0
.
0
0
.
0
0
.
0
0
.
0
1
.
Ch 32
Ch 33
.
1
1
1
1
1
1
1
1
0
1
Ch 62
Ch 63
1
1
1
1
1
1
1
1
1
1
0
0
.
0
0
.
0
0
.
0
0
.
0
0
.
0
1
.
Ch 64
Ch 65
.
1
1
1
1
1
1
1
1
1
1
0
1
Ch 126
Ch 127
Notes:
1. Bit A7 must be high for access to data and connection memory positions. Bit A7 must be low for access to registers.
2. Channels 0 to 31 are used when serial interface is at 2Mb/s mode.
3. Channels 0 to 63 are used when serial interface is at 4Mb/s mode.
4. Channels 0 to 127 are used when serial interface is at 8Mb/s mode.
Table 4 - Internal Register and Address Memory Mapping
OE bit in Connection
ODE pin
OSB bit in IMS register
ST-BUS Output Driver Status
Memory
0
Don’t Care
Don’t Care
Per Channel
High Impedance
1
1
1
0
0
1
0
1
High Impedance
Enable
Don’t care
Enable
Table 5 - Output High Impedance Control
If the LPBK bit is low, the loopback feature is disabled. For proper per-channel loopback operation, the contents of
the frame delay offset registers must be set to zero.
15
Zarlink Semiconductor Inc.
MT90823
Data Sheet
Initialization of the MT90823
During power up, the TRST pin should be pulsed low, or held low continuously, to ensure that the MT90863 is in the
normal functional mode. A 5K pull-down resistor can be connected to this pin so that the device will not enter the
JTAG test mode during power up.
Upon power up, the contents of the connection memory can be in any state and the ODE pin should be held low to
keep all ST-BUS outputs in a high impedance state until the microprocessor has initialized the switching matrix.
To prevent two ST-BUS outputs from driving the same stream simultaneously, the microprocessor should program
the desired active paths through the switch and put all other channels into a high impedance state during the
initialization routine by using the block programming mode. In addition, the loopback bits in the connection memory
should be cleared for normal operation.
When this process is complete, the microprocessor controlling the matrices can bring the ODE pin or OSB bit high
to relinquish the high impedance state control to the OE bit in the connection memory.
Read/Write Address:
Reset Value:
00H,
0000H.
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
0
0
0
MBP
MS STA3 STA2 STA1 STA0
Bit
Name
Description
15 - 6
5
Unused
MBP
Must be zero for normal operation.
Memory Block Program. When 1, the connection memory block programming
feature is ready for the programming of Connection Memory high bits, bit 11 to bit 15.
When 0, this feature is disabled.
4
MS
Memory Select. When 0, connection memory is selected for read or write operations.
When 1, the data memory is selected for read operations and connection memory is
selected for write operations. (No microprocessor write operation is allowed for the
data memory.)
3 - 0
STA3-0
Stream Address Bits. The binary value expressed by these bits refers to the input or
output data stream, which corresponds to the subsection of memory made accessible
for subsequent operations. (STA3 = MSB, STA0 = LSB)
Table 6 - Control (CR) Register Bits
Input/Output
Data Rate
Valid Address Lines
2.048 Mb/s
4.096 Mb/s
8.192 Mb/s
A4, A3, A2, A1, A0
A5, A4, A3, A2, A1, A0
A6, A5, A4 A3, A2, A1, A0
Table 7 - Valid Address lines for Different Bit Rates
16
Zarlink Semiconductor Inc.
MT90823
Data Sheet
Read/Write Address:
Reset Value:
01H,
0000H.
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
BPD
3
BPD BPD
BPD
0
BPD
4
0
0
0
0
0
0
BPE OSB SFE
DR1
DR0
2
1
Bit
Name
Description
15-10
9-5
Unused
BPD4-0
Must be zero for normal operation.
Block Programming Data. These bits carry the value to be loaded into the
connection memory block whenever the memory block programming feature is
activated. After the MBP bit in the control register is set to 1 and the BPE bit is set to
1, the contents of the bits BPD4- 0 are loaded into bit 15 to bit 11 of the connection
memory. Bit 10 to bit 0 of the connection memory are set to 0.
4
BPE
Begin Block programming Enable. A zero to one transition of this bit enables the
memory block programming function. The BPE and BPD4-0 bits in the IMS register
have to be defined in the same write operation. Once the BPE bit is set high, the
device requires two frames to complete the block programming. After the
programming function has finished, the BPE bit returns to zero to indicate the
operation is completed. When the BPE = 1, the BPE or MBP can be set to 0 to abort
the programming operation.
When BPE = 1, the other bits in the IMS register must not be changed for two frames
to ensure proper operation.
3
2
OSB
SFE
Output standby. When ODE = 0 and OSB = 0, the output drivers of STo0 to STo15
are in high impedance mode. When ODE = 0 and OSB = 1, the output driver of STo0
to STo15 function normally. When ODE = 1, STo0 to STo15 output drivers function
normally.
Start Frame Evaluation. A zero to one transition in this bit starts the frame evaluation
procedure. When the CFE bit in the FAR register changes from zero to one, the
evaluation procedure stops. To start another frame evaluation cycle, set this bit to
zero for at least one frame.
1 - 0
DR1-0
Data Rate Select. Input/Output data rate selection. See Table 9 for detailed
programming.
Table 8 - Interface Mode Selection (IMS) Register Bits
DR1
DR0
Data Rate Selected
Master Clock Required
0
0
1
1
0
1
0
1
2.048 Mb/s
4.096 Mb/s
8.192 Mb/s
Reserved
4.096 MHz
8.192 MHz
16.384 MHz
Reserved
Table 9 - Serial Data Rate Selection (16 input x 16 output)
17
Zarlink Semiconductor Inc.
MT90823
Data Sheet
Read Address:
Reset Value:
02H,
0000H.
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
0
CFE
FD11 FD10 FD9
FD8
FD7
FD6
FD5
FD4
FD3
FD2
FD1
FD0
0
Bit
Name
Description
Must be zero for normal operation.
15 - 13
12
Unused
CFE
Complete Frame Evaluation. When CFE = 1, the frame evaluation is
completed and bits FD10 to FD0 bits contains a valid frame alignment offset.
This bit is reset to zero, when SFE bit in the IMS register is changed from 1 to
0.
11
FD11
Frame Delay Bit 11. The falling edge of FE (or rising edge for GCI mode) is
sampled during the CLK-high phase (FD11 = 1) or during the CLK-low phase
(FD11 = 0). This bit allows the measurement resolution to 1/2 CLK cycle.
10 - 0
FD10-0
Frame Delay Bits. The binary value expressed in these bits refers to the
measured input offset value. These bits are reset to zero when the SFE bit of
the IMS register changes from 1 to 0. (FD10 = MSB, FD0 = LSB)
Table 10 - Frame Alignment (FAR) Register Bits
18
Zarlink Semiconductor Inc.
MT90823
Data Sheet
ST-BUS Frame
CLK
Offset Value
FE Input
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16
(FD[10:0] = 06H)
(FD11 = 0, sample at CLK low phase)
GCI Frame
CLK
Offset Value
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
FE Input
(FD[10:0] = 09 )
H
(FD11 = 1, sample at CLK high phase)
Figure 4 - Example for Frame Alignment Measurement
19
Zarlink Semiconductor Inc.
MT90823
Data Sheet
Read/Write Address:
Reset value:
03H for FOR0 register,
04H for FOR1 register,
05H for FOR2 register,
06H for FOR3 register,
0000H for all FOR registers.
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
OF32
OF31
OF30 DLE3 OF22
OF21 OF20
DLE2 OF12
OF11 OF10
DLE1 OF02
OF01 OF00
DLE0
FOR0 register
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
OF72
OF71
OF70 DLE7 OF62
OF61 OF60
DLE6 OF52
OF51 OF50
DLE5 OF42
OF41
OF40
DLE4
FOR1 register
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
OF112 OF111 OF110 DLE11 OF102 OF101 OF100 DLE10 OF92
OF91 OF90
DLE9 OF82
OF81
OF80
DLE8
FOR2 register
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
OF152 OF151 OF150 DLE15 OF142 OF141 OF140 DLE14 OF132 OF131 OF130 DLE13 OF122 OF121 OF120 DLE12
FOR3 register
Name
Description
(Note 1)
OFn2, OFn1, OFn0
Offset Bits 2,1 & 0. These three bits define how long the serial interface receiver takes
to recognize and store bit 0 from the STi input pin: i.e., to start a new frame. The input
frame offset can be selected to +4 clock periods from the point where the external
frame pulse input signal is applied to the F0i input of the device. See Figure 4.
DLEn
Data Latch Edge.
ST-BUS mode:DLEn =0, if clock rising edge is at the 3/4 point of the bit cell.
DLEn =1, if when clock falling edge is at the 3/4 of the bit cell.
GCI mode:DLEn =0, if clock falling edge is at the 3/4 point of the bit cell.
DLEn =1, if when clock rising edge is at the 3/4 of the bit cell.
Note 1: n denotes an input stream number from 0 to 15.
Table 11 - Frame Input Offset (FOR) Register Bits
20
Zarlink Semiconductor Inc.
MT90823
Data Sheet
Measurement Result from
Frame Delay Bits
Corresponding
Offset Bits
Input Stream
Offset
FD11
FD2
0
FD1
0
FD0
0
OFn2
OFn1 OFn0
DLEn
No clock period shift (Default)
+ 0.5 clock period shift
+1.0 clock period shift
+1.5 clock period shift
+2.0 clock period shift
+2.5 clock period shift
+3.0 clock period shift
+3.5 clock period shift
+4.0 clock period shift
+4.5 clock period shift
1
0
1
0
1
0
1
0
1
0
0
0
0
0
0
0
0
0
1
1
0
0
0
1
0
1
0
1
0
1
0
1
0
0
0
0
0
0
1
1
1
1
0
0
0
1
1
0
0
1
1
0
0
0
0
1
0
0
1
0
1
0
0
1
0
0
1
1
0
1
1
1
0
0
1
0
0
Table 12 - Offset Bits (OFn2, OFn1, OFn0, DLEn) and Frame Delay Bits (FD11, FD2-0)
ST-BUS F0i
CLK
offset=0, DLE=0
offset=1, DLE=0
offset=0, DLE=1
offset=1, DLE=1
STi Stream
Bit 7
Bit 7
STi Stream
STi Stream
STi Stream
Bit 7
Bit 7
denotes the 3/4 point of the bit cell
GCI F0i
CLK
offset=0, DLE=0
offset=1, DLE=0
offset=0, DLE=1
offset=1, DLE=1
Bit 0
Input Stream
Bit 0
Input Stream
Input Stream
Input Stream
Bit 0
Bit 0
denotes the 3/4 point of the bit cell
Figure 5 - Examples for Input Offset Delay Timing
21
Zarlink Semiconductor Inc.
MT90823
Data Sheet
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
V/C
MC CSTo
OE
SAB3 SAB2 SAB1 SAB0 CAB6 CAB5 CAB4 CAB3 CAB2 CAB1 CAB0
LPBK
Bit
Name
Description
15
LPBK
Per Channel Loopback. This bit should be use for diagnostic purpose only.
Set this bit to zero for normal operation. When loopback bit is set for all
memory location, the STi n channel m data comes from STo n channel m. For
proper per channel loopback operations, set the delay offset register bits
OFn[2:0] to zero for the streams which are in the loopback mode.
14
13
V/C
MC
Variable /Constant Throughput Delay. This bit is used to select between
the variable (low) and the constant delay (high) modes on a per-channel
basis.
Message Channel. When 1, the contents of the connection memory are
output on the corresponding output channel and stream. Only the lower byte
(bit 7 - bit 0) will be output to the ST-BUS output pins. When 0, the contents of
the connection memory are the data memory address of the switched input
channel and stream.
12
11
CSTo
OE
Control ST-BUS output. This bit is output on the CSTo pin one channel
early. The CSTo bit for stream 0 is output first.
Output Enable. This bit enables the ST-BUS output drivers on a per-channel
basis.
When 1, the output driver functions normally. When 0, the output driver is in a
high-impedance state.
10 - 8,
7
(Note 1)
SAB3-0
CAB6-0
Source Stream Address Bits. The binary value is the number of the data
stream for the source of the connection.
6 - 0
(Note 1)
Source Channel Address Bits. The binary value is the number of the
channel for the source of the connection.
Note 1: If bit 13 (MC) of the corresponding connection memory location is 1 (device in message mode), then these entire 8 bits
(SAB0, CAB6 - CAB0) are output on the output channel and stream associated with this location.
Table 13 - Connection Memory Bits
Data Rate
CAB Bits Used to Determine the Source Channel of the Connection
2.048 Mb/s
4.096 Mb/s
8.192 Mb/s
CAB4 to CAB0 (32 channel/input stream)
CAB5 to CAB0 (64 channel/input stream)
CAB6 to CAB0 (128 channel/input stream)
Table 14 - CAB Bits Programming for Different Data Rates
22
Zarlink Semiconductor Inc.
MT90823
Data Sheet
JTAG Support
The MT90823 JTAG interface conforms to the IEEE 1149.1 Boundary-Scan standard and the Boundary-Scan Test
(BST) design-for-testability technique it specifies. The operation of the boundary-scan circuitry is controlled by an
external test access port (TAP) Controller.
Test Access Port (TAP)
The Test Access Port (TAP) provides access to the many test functions of the MT90823. It consists of three input
pins and one output pin. The following pins comprise the TAP.
•
•
•
Test Clock Input (TCK)
TCK provides the clock for the test logic. The TCK does not interfere with any on-chip clock and thus
remains independent. The TCK permits shifting of test data into or out of the Boundary-Scan register cells
concurrently with the operation of the device and without interfering with the on-chip logic.
Test Mode Select Input (TMS)
The logic signals received at the TMS input are interpreted by the TAP Controller to control the test
operations. The TMS signals are sampled at the rising edge of the TCK pulse. This pin is internally pulled to
Vdd when it is not driven from an external source.
Test Data Input (TDI)
Serial input data applied to this port is fed either into the instruction register or into a test data register,
depending on the sequence previously applied to the TMS input. Both registers are described in a
subsequent section. The received input data is sampled at the rising edge of TCK pulses. This pin is
internally pulled to Vdd when it is not driven from an external source.
•
•
Test Data Output (TDO)
Depending on the sequence previously applied to the TMS input, the contents of either the instruction
register or data register are serially shifted out towards the TDO. The data out of the TDO is clocked on the
falling edge of the TCK pulses. When no data is shifted through the boundary scan cells, the TDO driver is
set to a high impedance state.
Test Reset (TRST)
Resets the JTAG scan structure. This pin is internally pulled to VDD.
Instruction Register
In accordance with the IEEE 1149.1 standard, the MT90823 uses public instructions. The MT90823 JTAG Interface
contains a three-bit instruction register. Instructions are serially loaded into the instruction register from the TDI
when the TAP Controller is in its shifted-IR state. Subsequently, the instructions are decoded to achieve two basic
functions: to select the test data register that may operate while the instruction is current, and to define the serial
test data register path, which is used to shift data between TDI and TDO during data register scanning.
23
Zarlink Semiconductor Inc.
MT90823
Data Sheet
Test Data Register
As specified in IEEE 1149.1, the MT90823 JTAG Interface contains three test data registers:
•
The Boundary-Scan Register
The Boundary-Scan register consists of a series of Boundary-Scan cells arranged to form a scan path
around the boundary of the MT90823 core logic.
•
•
The Bypass Register
The Bypass register is a single stage shift register that provides a one-bit path from TDI to its TDO.
The Device Identification Register
The device identification register is a 32-bit register with the register contain of:
MSB
LSB
0000 0000 1000 0010 0011 0001 0100 1011
The LSB bit in the device identification register is the first bit clocked out.
The MT90823 boundary scan register contains 118 bits. Bit 0 in Table 15 Boundary Scan Register is the first bit
clocked out. All tristate enable bits are active high.
24
Zarlink Semiconductor Inc.
MT90823
Data Sheet
Boundary Scan Bit 0 to Bit 117
Output
Scan
Cell
Input
Scan
Cell
Device Pin
Tristate
Control
STo7
STo6
STo5
STo4
STo3
STo2
STo1
STo0
0
2
4
6
8
10
12
14
1
3
5
7
9
11
13
15
ODE
CSTo
DTA
16
17
18
19
D15
D14
D13
D12
D11
D10
D9
20
23
26
29
32
35
38
41
21
24
27
30
33
36
39
42
22
25
28
31
34
37
40
43
D8
AD7
AD6
AD5
AD4
AD3
AD2
AD1
AD0
44
47
50
53
56
59
62
65
45
48
51
54
57
60
63
66
46
49
52
55
58
61
64
67
IM
AS/ALE
CS
68
69
70
71
72
R/W / WR
DS/RD
Table 14 - Boundary Scan Register Bits
25
Zarlink Semiconductor Inc.
MT90823
Data Sheet
Boundary Scan Bit 0 to Bit 117
Output
Scan
Cell
Input
Scan
Cell
Device Pin
Tristate
Control
A7
A6
A5
A4
A3
A2
A1
A0
73
74
75
76
77
78
79
80
WFPS
RESET
CLK
81
82
83
84
85
FE/HCLK
F0i
STi15
STi14
STi13
STi12
STi11
STi10
STi9
STi8
STi7
STi6
STi5
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
STi4
STi3
STi2
STi1
STi0
STo15
STo14
STo13
STo12
STo11
STo10
STo9
102
104
106
108
110
112
114
116
103
105
107
109
111
113
115
117
STo8
Table 14 - Boundary Scan Register Bits (continued)
26
Zarlink Semiconductor Inc.
MT90823
Data Sheet
Applications
Switch Matrix Architectures
The MT90823 is an ideal device for medium to large size switch matrices where voice and grouped data channels
are transported within the same frame. In such applications, the voice samples have to be time interchanged with a
minimum delay while maintaining the integrity of grouped data. To ensure the integrity of grouped data during
switching and to provide a minimum delay for voice connections, the MT90823 provides per-channel selection
between variable and constant throughput delay. This can be selected by the V/C bit of the Connection Memory.
Figure 6 illustrates how four MT90823 devices can be used to form non-blocking switches for up to 4096 channels
with data rate of 8.192 Mb/s.
Serial Input Frame Alignment Evaluation
The MT90823 is capable of performing frame alignment evaluation. The frame pulse under evaluation is connected
to the FE (frame measurement) pin. An external multiplexer is required to select one of the frame pulses related to
the different input streams. Figure 7 - The block diagram at Figure 7 shows a switch matrix that performs frame
alignment evaluation for 16 frame pulses.
16 Streams
16 Streams
MT90823
#1
IN
16 Streams
OUT
16 Streams
MT90823
#2
MT90823
#3
Bit Rate
Size of
(IN/OUT)
Switch Matrix
2.048 Mb/s 1,024 - Channel Switch
4.096 Mb/s 2,048 - Channel Switch
8.192 Mb/s 4,096 - Channel Switch
MT90823
#4
Figure 6 - Switch Matrix with Serial Stream at Various Bit Rates
27
Zarlink Semiconductor Inc.
MT90823
Data Sheet
STi0
STi1
STi2
MT90823
Frame Alignment
Evaluation circuit
STo[0:15]
STi15
External
Mux
FE
CLK
FP
input
FP STi0
FP STi1
FP STi2
Central
Timing Source
FP STi15
Note:
1. Use the external mux to select one of the serial frame pulses.
2. To start a measurement cycle, set the Start Frame Evaluation (SFE) bit in the IMS register low for at least 1 frame.
3. Frame evaluation starts when the SFE bit is changed from low to high.
4. Two frames later, the Complete Frame Evaluation (CFE) bit of the Frame Alignment Register (FAR) changes from low
to high to signal the CPU that a valid offset measurement is ready to be read from bit [11:0] of the FAR register.
5. The SFE bit must be set to zero before a new measurement cycle started.
Figure 7 - Serial Input Frame Alignment Evaluation for Various Frame Pulses
Wide Frame Pulse (WFP) Frame Alignment Mode
When the device is in the wide frame pulse mode and if the input data streams are sampled at 3/4 bit time, the
device can operate in the HMVIP and MVIP-90 environment. When input data streams are sampled at half-bit time
as specified in the HMVIP and MVIP-90 standard, the device can only operate with data rate of 2 Mb/s. Refer to the
ST-BUS output delay parameter, tSOD, as specified in the AC Electrical Characteristic table.
The MT90823 is designed to accept a common frame pulse F0i, the 4.096 MHz and 16.384 MHz clocks required by
the HMVIP standards. To enable the Wide Frame Pulse Frame Alignment Mode, the WFPS pin has to be set to
HIGH and the DR1 and DR0 bits set for 8.192M b/s data rate operation.
Digital Access Cross-Connect System
Figure 8 illustrates the use of MT90823 devices to construct a 256 E1/T1 Digital Access Cross- connect System
(DACS). The system consists of 32 trunk cards each having eight E1 or T1 trunk interfaces for a total of 256 trunks.
Each trunk card uses two MT8986 Multi-rate Digital Switches. The central switching block uses 16 MT90823
devices.
The block diagram at Figure 9 shows how an 8,192 x 8,192 channel switch can be constructed from 4,096 x 4,096
channel switch modules. Figure 6 shows the implementation of the individual 4,096 x 4,096 channel switch
modules from four MT90823 devices.
Figure 10 shows an eight-stream trunk card using MT8986 Multi-rate Digital Switches to concentrate 32-channel
2.048 Mb/s ST-BUS (DSTi and DSTo) streams at each E1/T1 trunk onto four 128-channel 8.192 Mb/s streams.
The DACS switching matrix that formerly required 256 MT8986 devices in a square (16 x 16) configuration can now
be provided by 64 MT8986 and 16 MT90823 devices (see Figure 8).
28
Zarlink Semiconductor Inc.
MT90823
Data Sheet
Each line represents a stream
TC0
that consists of
E10
E17
128 channels at 8.192 Mb/s
8 x E1/T1
Trunk Card
8,192 x 8,192 channel
Switch Matrix
TC1
E18
8 x E1/T1
Trunk Card
E115
Sixteen MT90823
(8 Mb/s mode)
64 input streams
x
(See Figure 9)
TC31
64 output streams
E1247
E1255
8 x E1/T1
Trunk Card
(Figure 10)
Figure 8 - 256 E1/T1 Digital Access Cross-Connect System (DACS)
32 Streams
4,096 x 4,096
Switch Matrix
(Figure 6)
4,096 x 4,096
Switch Matrix
(Figure 6)
32 Streams
IN
OUT
32 Streams
4,096 x 4,096
Switch Matrix
(Figure 6)
4,096 x 4,096
Switch Matrix
(Figure 6)
32 Streams
Figure 9 - 8,192 x 8,192 Channel Switch Matrix
29
Zarlink Semiconductor Inc.
MT90823
Data Sheet
DSTo
DSTi
STi0
STi1
E10
E11
E1/T1 Trunk 0
E1/T1 Trunk 1
MT8986
2 Mb/s
to
STo0
STo1
256-channel out
DSTo
DSTi
8 Mb/s
STi7
(8.192 Mb/s per channel)
STo0
STo1
MT8986
8 Mb/s
to
STi0
STi1
256-channel in
DSTo
DSTi
E17
E1/T1 Trunk 7
2 Mb/s
STo7
(8.192 Mb/s per channel)
Figure 10 - Trunk Card Block Diagram
Absolute Maximum Ratings*
Parameter
Sym.
Min.
Max.
Units
1
2
3
4
5
6
Supply Voltage
VDD
VI
VI
Io
PD
TS
-0.3
VSS - 0.3
VSS - 0.3
5.0
VDD + 0.3
5.5
V
V
V
mA
W
°C
Voltage on any 3.3 V Tolerant pin I/O (other than supply pins)
Voltage on any 5 V Tolerant pin I/O (other than supply pins)
Continuous Current at digital outputs
Package power dissipation (PLCC & PQFP)
Storage temperature
20
1
+125
- 65
* Exceeding these values may cause permanent damage. Functional operation under these conditions is not implied
Recommended Operating Conditions - Voltages are with respect to ground (V ) unless otherwise stated.
ss
Characteristics
Sym.
Min.
Typ.
Max.
Units
Test Conditions
1
2
3
4
Operating Temperature
Positive Supply
Input High Voltage
Input High Voltage on 5 V Tolerant
Inputs
Input Low Voltage
TOP
VDD
VIH
-40
3.0
0.7VDD
+85
3.6
VDD
5.5
°C
V
V
400 mV noise margin
400 mV noise margin
VIH
V
5
VIL
VSS
0.3VDD
V
30
Zarlink Semiconductor Inc.
MT90823
Data Sheet
DC Electrical Characteristics - Voltages are with respect to ground (V ) unless otherwise stated.
ss
Characteristics
Sym.
Min.
Typ.
Max.
Units Test Conditions
1
@ 2 Mb/s
@ 4 Mb/s
@ 8 Mb/s
12
20
45
15
26
70
mA
mA
mA
V
V
Supply Current
IDD
Output unloaded
I
N
P
U
T
S
2
3
4
Input High Voltage
Input Low Voltage
Input Leakage (input pins)
Input Leakage (with pull-up or pull-
down)
VIH
VIL
0.7VDD
0.3VDD
15
50
IIL
µA
IBL
µA
0≤<V≤VDD See
Note 1
5
6
7
8
Input Pin Capacitance
Output High Voltage
Output Low Voltage
CI
10
pF
V
V
VOH
VOL
IOZ
0.8VDD
IOH = -10 mA
IOL = 10 mA
0 < V < VDD See
Note 1
O
U
T
0.4
5
P
U
T
High Impedance Leakage
µA
S
9
Note:
Output Pin Capacitance
CO
10
pF
1. Maximum leakage on pins (output or I/O pins in high impedance state) is over an applied voltage (V)
AC Electrical Characteristics - Timing Parameter Measurement Voltage Levels
Characteristics
Sym.
Level
Units
Conditions
1
2
3
CMOS Threshold
Rise/Fall Threshold Voltage High
Rise/Fall Threshold Voltage Low
VCT
VHM
VLM
0.5VDD
0.7VDD
0.3VDD
V
V
V
31
Zarlink Semiconductor Inc.
MT90823
Data Sheet
AC Electrical Characteristics - Frame Pulse and CLK
Characteristic
Sym.
tFPW
Min.
Typ.
Max.
Units
Notes
WFPS Pin = 0
1
Frame pulse width (ST-BUS, GCI)
Bit rate = 2.048 Mb/s
26
26
26
295
145
80
ns
ns
ns
Bit rate = 4.096 Mb/s
Bit rate = 8.192 Mb/s
tFPS
tFPH
tCP
2
3
4
Frame Pulse Setup time before
CLK falling (ST-BUS or GCI)
Frame Pulse Hold Time from CLK
falling (ST-BUS or GCI)
5
ns
WFPS Pin = 0
WFPS Pin = 0
10
ns
CLK Period
Bit rate = 2.048 Mb/s
Bit rate = 4.096 Mb/s
Bit rate = 8.192 Mb/s
190
110
55
300
150
70
ns
ns
ns
WFPS Pin = 0
WFPS Pin = 0
WFPS Pin = 0
tCH
5
6
CLK Pulse Width High
Bit rate = 2.048 Mb/s
Bit rate = 4.096 Mb/s
Bit rate = 8.192 Mb/s
CLK Pulse Width Low
Bit rate = 2.048 Mb/s
Bit rate = 4.096 Mb/s
Bit rate = 8.192 Mb/s
85
50
20
150
75
ns
ns
ns
40
tCL
85
50
20
150
75
ns
ns
ns
40
tr, tf
7
8
Clock Rise/Fall Time
Wide frame pulse width
Bit rate = 8.192 Mb/s
Frame Pulse Setup Time before
HCLK falling
10
295
ns
ns
tHFPW
195
5
WFPS Pin = 1
WFPS Pin = 1
WFPS Pin = 1
WFPS Pin = 1
WFPS Pin = 1
tHFPS
tHFPH
tHCP
9
150
150
300
150
ns
ns
ns
ns
10 Frame Pulse Hold Time from
HCLK falling
11 HCLK (4.096MHz) Period
Bit rate = 8.192 Mb/s
12 HCLK (4.096MHz) Pulse Width
High
10
190
85
tHCH
Bit rate = 8.192 Mb/s
tHCL
13 HCLK (4.096MHz) Pulse Width
Low
85
150
ns
WFPS Pin = 1
Bit rate = 8.192 Mb/s
tHr, tHf
tDIF
14 HCLK Rise/Fall Time
15 Delay between falling edge of
HCLK and falling edge of CLK
10
10
ns
ns
-10
WFPS Pin = 0 or 1
32
Zarlink Semiconductor Inc.
MT90823
Data Sheet
AC Electrical Characteristics - Serial Streams for ST-BUS and GCI Backplanes
Characteristic
Sym. Min.
Typ.
Max.
Units
Test Conditions
tSIS
tSIH
1
2
3
Sti Set-up Time
Sti Hold Time
Sto Delay - Active to Active
0
10
ns
ns
ns
ns
tSOD
30
40
CL=30pF
CL=200pF
4
5
6
STo delay - Active to High-Z
Sto delay - High-Z to Active
Output Driver Enable (ODE)
Delay
tDZ
tZD
tODE
32
32
32
RL=1K, CL=200pF, See Note 1
RL=1K, CL=200pF, See Note 1
RL=1K, CL=200pF, See Note 1
ns
7
CSTo Output Delay
tXCD
30
40
ns
ns
CL=30pF
CL=200pF
Note:
1. High Impedance is measured by pulling to the appropriate rail with R , with timing corrected to cancel time taken to discharge C .
L
L
tFPW
F0i
VCT
tCP
tCH
tFPS
tr
tFPH
tCL
VHM
VTT
VLM
CLK
tSOD
tf
Bit 0, Last Ch (Note1)
Bit 7, Channel 0
Bit 6, Channel 0
Bit 5, Channel 0
STo
VCT
tSIS
tSIH
STi
Bit 0, Last Ch (Note1)
Bit 7, Channel 0
Bit 6, Channel 0
Bit 5, Channel 0
VCT
Note 1:
2.048 Mb/s mode, last channel = ch 31,
4.196 Mb/s mode, last channel = ch 63,
8.192 Mb/s mode, last channel = ch 127.
Figure 11 - ST-BUS Timing for 2.048 Mb/s and High Speed Serial Interface at 4.096 Mb/s
or 8.192 Mb/s, when WFPS pin = 0.
33
Zarlink Semiconductor Inc.
MT90823
Data Sheet
tFPW
F0i
VCT
tCP
tCH
tFPS
tFPH
tCL
tr
VHM
VCT
VLM
CLK
tSOD
tf
Bit 7, Last Ch (Note1)
Bit 0, Channel 0
Bit 1, Channel 0
Bit 2, Channel 0
Bit 2, Channel 0
STo
VCT
tSIS
tSIH
STi
Bit 7, Last Ch (Note1)
Bit 0, Channel 0
Bit 1, Channel 0
VCT
Note 1:
2 Mb/s mode, last channel = ch 31,
4 Mb/s mode, last channel = ch 63,
8 Mb/s mode, last channel = ch 127
Figure 12 - GCI Timing at 2.048 Mb/s and High Speed Serial Interface
at 4.096 Mb/s or 8.192 Mb/s, when WFPS pin = 0
tHFPW
tHFPS
tHFPH
VCT
F0i
tHCP
tHCH
tHCL
HCLK
4.096MHz
VHM
VCT
VLM
tDIF
tHf
tHr
tCP
tCH
tCL
tr
CLK
VCT
VCT
VCT
16.384MHz
tSOD
tf
Bit 1, Ch 127
Bit 1, Ch 127
Bit 0, Ch 127
Bit 7, Ch 0
Bit 6, Ch 0
Bit 5, Ch 0
Bit 4, Ch 0
STo
STi
tSIS
tSIH
Bit 0, Ch 127
Bit 7, Ch 0
Bit 6, Ch 0
Bit 5, Ch 0
Bit 4, Ch 0
Figure 13 - WFP Bus Timing for High Speed Serial Interface (8.192 Mb/s), when WFPS pin = 1
Note:
1. High Impedance is measured by pulling to the appropriate rail with R , with timing corrected to cancel time taken to discharge C .
L
L
34
Zarlink Semiconductor Inc.
MT90823
Data Sheet
CLK
VCT
(ST-BUS or)
(WFPS mode)
CLK
(GCI mode)
VCT
tDZ
VCT
VCT
VCT
HiZ
Valid Data
STo
STo
tZD
Valid Data
HiZ
tXCD
CSTo
Figure 14 - Serial Output and External Control
VCT
ODE
tODE
tODE
VCT
Valid Data
STo
HiZ
HiZ
Figure 15 - Output Driver Enable (ODE)
35
Zarlink Semiconductor Inc.
MT90823
Data Sheet
AC Electrical Characteristics - Multiplexed Bus Timing (Mode 1)
Characteristics
Sym.
Min.
Typ.
Max.
Units
Test Conditions
1
2
3
4
5
6
7
8
9
ALE pulse width
tALW
tADS
tADH
tALRD
tDDR
tCSRW
tRW
20
3
3
3
5
5
45
0
ns
ns
ns
ns
ns
ns
ns
ns
ns
Address setup from ALE falling
Address hold from ALE falling
RD active after ALE falling
Data setup from DTA Low on Read
CS hold after RD/WR
RD pulse width (fast read)
CS setup from RD
Data hold after RD
CL=150pF
tCSR
tDHR
10
20
CL=150pF, RL=1K,
Note 1.
10 WR pulse width (fast write)
11 WR delay after ALE falling
12 CS setup from WR
13 Data setup from WR (fast write)
14 Valid Data Delay on write (slow write) tSWD
tWW
tALWR
tCSW
tDSW
45
3
0
ns
ns
ns
ns
ns
ns
20
122
15 Data hold after WR inactive
tDHW
tAKD
5
16 Acknowledgment Delay:
Reading/Writing Registers
Reading/Writing Memory @ 2Mb/s
@ 4Mb/s
43/43
ns
ns
ns
ns
CL=150pF
CL=150pF
CL=150pF
CL=150pF
760/750
400/390
220/210
@ 8Mb/s
17 Acknowledgment Hold Time
tAKH
22
ns
CL=150pF, RL=1K,
Note 1.
Note:
1. High Impedance is measured by pulling to the appropriate rail with RL, with timing corrected to cancel time taken to discharge CL.
36
Zarlink Semiconductor Inc.
MT90823
Data Sheet
tALW
VCT
ALE
tADS
tADH
AD0-AD7
D8-D15
VCT
HiZ
HiZ
HiZ
ADDRESS
tALRD
DATA
tCSRW
CS
RD
VCT
tCSR
tRW
VCT
tDHR
tWW
VCT
WR
tCSW
tDHW
tAKH
tSWD
tDSW
tALWR
tDDR
DTA
VCT
tAKD
Figure 16 - Multiplexed Bus Timing (Mode 1)
37
Zarlink Semiconductor Inc.
MT90823
Data Sheet
AC Electrical Characteristics - Multiplexed Bus Timing (Mode 2)
Characteristics
Sym.
Min.
Typ.
Max.
Units
Test Conditions
1
2
3
4
5
6
7
8
9
AS pulse width
tASW
tADS
tADH
tDDR
tCSH
tCSS
tDHW
20
3
3
5
0
0
5
20
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Address setup from AS falling
Address hold from AS falling
Data setup from DTA Low on Read
CS hold after DS falling
CS setup from DS rising
Data hold after write
CL=150pF
Data setup from DS -Write (fast write) tDWS
Valid Data Delay on write (slow write) tSWD
122
20
10 R/W setup from DS rising
11 R/W hold after DS falling
12 Data hold after read
tRWS
tRWH
tDHR
60
5
10
CL=150pF, RL=1K,
Note 1
13 DS delay after AS falling
tDSH
tAKD
10
ns
14 Acknowledgment Delay:
Reading/Writing Registers
Reading/Writing Memory @ 2Mb/s
@ 4Mb/s
43/43
ns
ns
ns
ns
CL=150pF
CL=150pF
CL=150pF
CL=150pF
760/750
400/390
220/210
@ 8Mb/s
15 Acknowledgment Hold Time
tAKH
22
ns
CL=150pF, RL=1K,
Note 1
Note 1. High Impedance is measured by pulling to the appropriate rail with RL, with timing corrected to cancel time taken to discharge CL.
38
Zarlink Semiconductor Inc.
MT90823
Data Sheet
DS
VCT
tRWS
tRWH
R/W
VCT
tDSH
tASW
VCT
AS
tADS
tADH
tDHW
tDWS
tSW
HiZ
AD0-AD7
D8-D15
WR
DATA
VCT
HiZ
HiZ
ADDRESS
tDHR
AD0-AD7
D8-D15
RD
DATA
VCT
HiZ
ADDRESS
tCSH
tCSS
VCT
CS
tAKH
tDDR
tAKD
DTA
VCT
Figure 17 - Multiplexed Bus Timing (Mode2)
39
Zarlink Semiconductor Inc.
MT90823
Data Sheet
AC Electrical Characteristics - Motorola Non-Multiplexed Bus Mode
Characteristics
Sym.
Min.
Typ.
Max.
Units
Test Conditions
1
2
3
4
5
6
7
8
CS setup from DS falling
R/W setup from DS falling
Address setup from DS falling
CS hold after DS rising
R/W hold after DS rising
Address hold after DS rising
Data setup from DTA Low on Read
Data hold on read
tCSS
tRWS
tADS
tCSH
tRWH
tADH
tDDR
tDHR
0
10
2
0
2
2
2
10
ns
ns
ns
ns
ns
ns
ns CL=150pF
ns CL=150pF, RL=1K
Note 1
20
9
Data setup on write (fast write)
tDSW
0
5
ns
ns
ns
10 Valid Data Delay on write (slow write) tSWD
11 Data hold on write
12 Acknowledgment Delay:
Reading/Writing Registers
Reading/Writing Memory @ 2Mb/s
@ 4Mb/s
122
tDHW
tAKD
43/43
ns CL=150pF
ns CL=150pF
ns CL=150pF
ns CL=150pF
760/750
400/390
220/210
@ 8Mb/s
13 Acknowledgment Hold Time
tAKH
22
ns CL=150pF, RL=1K,
Note 1
Note:
1. High Impedance is measured by pulling to the appropriate rail with RL, with timing corrected to cancel time taken to discharge CL.
40
Zarlink Semiconductor Inc.
MT90823
Data Sheet
VCT
DS
CS
tCSH
tCSS
VCT
tRWH
tRWS
VCT
R/W
tADS
tADH
VCT
VALID ADDRESS
A0-A7
tDHR
VALID READ DATA
tDHW
VALID WRITE DATA
AD0-AD7
D8-D15
READ
VCT
tDSW
tSWD
AD0-AD7
D8-D15
WRITE
VCT
tDDR
VCT
DTA
tAKD
tAKH
Figure 18 - Motorola Non-Multiplexed Bus Timing
41
Zarlink Semiconductor Inc.
Package Code : GA
c
Zarlink Semiconductor 2002 All rights reserved.
Previous package codes:
1
ISSUE
ACN
213934
20Jan03
DATE
APPRD.
For more information about all Zarlink products
visit our Web Site at
www.zarlink.com
Information relating to products and services furnished herein by Zarlink Semiconductor Inc. or its subsidiaries (collectively “Zarlink”) is believed to be reliable.
However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such
information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or
use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual
property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in
certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink.
This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part
of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other
information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the
capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute
any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and
suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does
not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in
significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink’s conditions of sale which are available on request.
Purchase of Zarlink’s I2C components conveys a licence under the Philips I2C Patent rights to use these components in and I2C System, provided that the system
conforms to the I2C Standard Specification as defined by Philips.
Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc.
Copyright Zarlink Semiconductor Inc. All Rights Reserved.
TECHNICAL DOCUMENTATION - NOT FOR RESALE
相关型号:
©2020 ICPDF网 联系我们和版权申明