TFS153C [VECTRON]

Filter specification; 过滤器规格
TFS153C
型号: TFS153C
厂家: Vectron International, Inc    Vectron International, Inc
描述:

Filter specification
过滤器规格

过滤器 LTE
文件: 总5页 (文件大小:231K)
中文:  中文翻译
下载:  下载PDF数据表文档文件
Filename: tfs 153c.doc  
Version 1.2  
23.09.2005  
VI TELEFILTER  
Filter specification  
TFS 153C  
1/5  
Measurement condition  
Ambient temperature:  
Input power level:  
Terminating impedance: *  
Input:  
23  
0
°C  
dBm  
63 || -34 pF  
55 || -44 pF  
Output:  
Characteristics  
Remark:  
The nominal frequency f is fixed at 153,6. The insertion loss a is defined as loss value determined at f Reference level for the relative attenuation a  
N
e
N.  
rel  
of the TFS153C is the insertion loss a . The centre frequency f is the arithmetic mean value of the upper and lower frequencies at the 3 dB filter  
e
c
attenuation level relative to the insertion loss a . All specified data are met within the operating temperature range.  
e
D a t a  
typ. value  
tolerance / limit  
a
11.5  
dB  
max.  
12.5  
dB  
Insertion loss  
e
(reference level)  
fN  
153,6  
10  
MHz  
MHz  
dB  
Nominal frequency  
Passband PB  
-
fN  
±
p-p  
0,2  
dB  
max.  
1
Ripple within PB  
Relative attenuation  
a
rel  
fN  
fN  
fN  
fN  
-
152,6  
15  
138,6  
168,6  
MHz ... fN  
MHz ... fN  
MHz ... fN  
MHz ... fN  
-
15  
MHz  
MHz  
MHz  
MHz  
45  
dB  
dB  
dB  
dB  
min.  
min.  
min.  
min.  
35  
35  
20  
35  
dB  
dB  
dB  
dB  
+
+
+
+
+
+
138,6  
168,6  
346,4  
40  
70  
70  
p-p  
MHz  
Group delay ripple  
10  
-
MHz ... fN  
+
10  
10  
45  
ns  
max.  
60  
ns  
fN  
Phase linearity  
10  
p-p  
MHz  
-
MHz ... fN  
+
4
70  
-
deg  
dB  
max.  
min.  
max.  
min.  
.
5
35  
17  
35  
deg  
dB  
fN  
Triple transit response suppression  
Input power level  
dBm  
dBm  
IP3**  
-
Third order intercept  
Input /Output return loss  
fN  
fN  
-
-
4
10  
MHz ... fN  
MHz ... fN  
+
+
4
10  
MHz  
MHz  
12  
9
dB  
dB  
min.  
min.  
10  
8
dB  
dB  
OTR  
-
-
-25 °C..... +85 °C  
Operating temperature range  
Storage temperature range  
-40 °C..... +85 °C  
-
TC ***  
-95  
ppm/K  
Temperature coefficient of frequency  
f
*) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference  
values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team.  
**) Measured with tones spaced at 5 MHz and 10 MHz above and below fC  
***) f (Hz) = Tcf(ppm/K) x (T - To) x fCAT (MHz).  
c
Generated:  
Checked / Approved:  
Tele Filter GmbH  
Potsdamer Straße 18  
D 14 513 TELTOW / Germany  
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30  
E-Mail: tft@telefilter.com  
VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is  
assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.  
Filename: tfs 153c.doc  
Version 1.2  
23.09.2005  
VI TELEFILTER  
Filter specification  
TFS 153C  
2/5  
Filter characteristic  
1.315  
1.27  
1.225  
1.18  
1.135  
1.09  
1.045  
1
0
0
-0.3  
-0.6  
-0.9  
-1.2  
-1.5  
-1.8  
-2.1  
-2.4  
-2.7  
-3  
-6  
-12  
-18  
-24  
-30  
-36  
-42  
-48  
-54  
-60  
0.955  
0.91  
0.865  
128.6 133.6 138.6 143.6 148.6 153.6 158.6 163.6 168.6 173.6 178.6  
frequency in MHz  
141.6 144 146.4 148.8 151.2 153.6 156 158.4 160.8 163.2 165.6  
frequency in MHz  
Construction and pin connection  
(All dimensions in mm)  
13,6Max.  
1
Ground  
2
3
4
5
6
7
8
Ground  
Ground  
Ground  
Output  
Output RF Return  
Ground  
Ground  
TFS 153C  
S25  
1
Date code  
9
Ground  
10  
11  
12  
Ground  
Input  
Input RF Return  
2,54 ±0,15  
1,5  
2
1
3 4  
12  
11  
5
6
Date code: Year + week  
S
T
2004  
2005  
2006  
U
...  
9 8  
10  
0,8  
7
0,1  
50 Ohm Test circuit  
L1  
C1  
L2  
11  
5
Input  
Output  
50 Ohm  
SAW  
50 Ohm  
C2  
1,2,3,4,6,7,8,9,10,12  
Tele Filter GmbH  
Potsdamer Straße 18  
D 14 513 TELTOW / Germany  
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30  
E-Mail: tft@telefilter.com  
VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is  
assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.  
Filename: tfs 153c.doc  
Version 1.2  
23.09.2005  
VI TELEFILTER  
Filter specification  
TFS 153C  
3/5  
Stability characteristics  
After the following tests the filter shall meet the whole specification:  
1. Shock:  
500g, 18 ms, half sine wave, 3 shocks each plane;  
DIN IEC 68 T2 - 27  
2. Vibration:  
10 Hz to 500 Hz, 0,35 mm or g respectively, 1 octave per min, 10 cycles per plan, 3 plans;  
DIN IEC 68 T2 - 6  
3. Change of  
temperature:  
-55 °C to 125°C / 30 min. each / 10 cycles  
DIN IEC 68 part 2 – 14 Test N  
4. Resistance to  
solder heat (reflow):  
reflow possible: twice max.;  
for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4;  
Packing  
Tape & Reel:  
IEC 286 – 3, with exeption of value for N and minimum bending radius;  
tape type II, embossed carrier tape with top cover tape on the upper side;  
max. pieces of filters peer reel:  
reel of empty components at start:  
reel of empty components at start including leader:  
trailer:  
1700  
min. 300 mm  
min. 500 mm  
min. 300 mm  
EMBOSSED CARRIER TAPE  
Tape (all dimensions in mm)  
2
Po  
P
D
o
W
: 24,00 +0,30/-0,10  
Po  
Do  
E
F
G(min)  
P2  
:
:
:
4,00 ± 0,1  
1,50 +0,1/-0  
1,75 ± 0,10  
E
F
o
A
1
: 11,50 ± 0,10  
:
:
D
0,60  
2,00 ± 0,1  
Ct  
W
o
B
P1  
: 12,00 ± 0,1  
D1(min)  
Ao  
:
:
1,50  
7,10 ± 0,10  
G
Bo  
Ct  
: 13,90 ± 0,10  
: 21,5 ± 0,1  
P1  
COVER TAPE  
W
2
Reel (all dimensions in mm)  
A
:330  
W1  
: 24,4 +2/-0  
W2(max) : 30,4  
N(min)  
C
: 60  
: 13,0 +0,5/-0,2  
C
A
N
W
1
The minimum bending radius is 45 mm. The mounting surface of the filters faces the bottom side of the embossed carrier tape. Marking  
of the filters can be read if the upper side of the carrier tape is regarded with the sprocket holes on the right.  
Tele Filter GmbH  
Potsdamer Straße 18  
D 14 513 TELTOW / Germany  
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30  
E-Mail: tft@telefilter.com  
VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is  
assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.  
Filename: tfs 153c.doc  
Version 1.2  
23.09.2005  
VI TELEFILTER  
Filter specification  
TFS 153C  
4/5  
Air reflow temperature conditions  
1st and 2nd air reflow profile  
Name:  
Temperature:  
Time:  
pre-heating periods main-heating periods  
peak temperature  
255 °C ± 5 °C  
150 °C - 170 °C  
60 sec. - 90 sec.  
over 200 °C  
20 sec. - 25 sec.  
Chip-mount air reflow profile  
260  
240  
220  
200  
180  
160  
140  
120  
100  
80  
60  
40  
20  
0
0
20  
40  
60  
80  
100  
120  
140  
160  
180  
200  
220  
240  
time / sec.  
Table for temperature vs. time during the air reflow process  
Tolerance of temperatures: ± 5 °C  
time / sec.  
0
10  
20  
30  
40  
50  
60  
70  
80  
90  
100  
110  
120  
130  
temperature / °C  
time / sec.  
temperature / °C  
23  
34  
46  
60  
80  
103  
121  
134  
143  
150  
154  
156  
158  
159  
140  
150  
160  
170  
180  
190  
195  
200  
205  
210  
215  
220  
230  
240  
160  
161  
164  
170  
180  
205  
230  
255  
230  
205  
180  
165  
140  
120  
Tele Filter GmbH  
Potsdamer Straße 18  
D 14 513 TELTOW / Germany  
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30  
E-Mail: tft@telefilter.com  
VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is  
assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.  
Filename: tfs 153c.doc  
Version 1.2  
23.09.2005  
VI TELEFILTER  
Filter specification  
TFS 153C  
5/5  
History  
Version  
Reason of Changes  
Name  
Date  
1.0  
1.1  
- generation of specification according to customer requirements  
Roizengaft  
Chilla  
02.02.2004  
15.06.2004  
- generated filter specification  
- added termination impedances  
- added typical values  
- changed insertion loss  
- changed group delay ripple  
- changed phase linearity  
- changed input/output return loss  
- changed IP3 description  
- changed storage temperature range  
- deleted description for power level  
- added filter characteristic  
- changed construction and pin connection  
- added test circuit  
- changed packing  
1.2  
- added temperature coefficient of frequency  
Chilla  
23.09.2005  
Tele Filter GmbH  
Potsdamer Straße 18  
D 14 513 TELTOW / Germany  
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30  
E-Mail: tft@telefilter.com  
VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is  
assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.  

相关型号:

TFS153D

Filter specification
VECTRON

TFS153E

Filter specification
VECTRON

TFS155

Filter Specification
VECTRON

TFS1552

Filter specification
VECTRON

TFS1555

Filter specification
VECTRON

TFS155A

Filter specification
VECTRON

TFS156

Filter Specification
VECTRON

TFS1569

Filter specification
VECTRON

TFS156A

Filter Specification
VECTRON

TFS156B

Filter specification
VECTRON

TFS156C

Filter specification
VECTRON

TFS1575

Filter specification
VECTRON