TPA4860 [TI]
1-W MONO AUDIO POWER AMPLIFIER; 1 -W单声道音频功率放大器
| 型号： | TPA4860 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 1-W MONO AUDIO POWER AMPLIFIER |
| 文件： | 总25页 (文件大小：430K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
TPA4860
1-W MONO AUDIO POWER AMPLIFIER
SLOS164A – SEPTEMBER 1996 – REVISED MARCH 2000
1-W BTL Output (5 V, 0.2 % THD+N)
3.3-V and 5-V Operation
D PACKAGE
(TOP VIEW)
No Output Coupling Capacitors Required
GND
SHUTDOWN
HP-SENSE
GND
GND
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
Shutdown Control (I
= 0.6 µA)
DD
V 2
O
IN+
IN–
Headphone Interface Logic
Uncompensated Gains of 2 to 20 (BTL
Mode)
BYPASS
HP-IN1
V
DD
GAIN
Surface-Mount Packaging
HP-IN2
V 1
O
Thermal and Short-Circuit Protection
GND
GND
High Power Supply Rejection
(56-dB at 1 kHz)
LM4860 Drop-In Compatible
description
The TPA4860 is a bridge-tied load (BTL) audio power amplifier capable of delivering 1 W of continuous average
power into an 8-Ω load at 0.4 % THD+N from a 5-V power supply in voiceband frequencies (f < 5 kHz). A BTL
configuration eliminates the need for external coupling capacitors on the output in most applications. Gain is
externally configured by means of two resistors and does not require compensation for settings of 2 to 20.
Features of this amplifier are a shutdown function for power-sensitive applications as well as headphone
interface logic that mutes the output when the speaker drive is not required. Internal thermal and short-circuit
protection increases device reliability. It also includes headphone interface logic circuitry to facilitate headphone
applications. The amplifier is available in a 16-pin SOIC surface-mount package that reduces board space and
facilitates automated assembly.
typical application circuit
V
12
10
DD
V
DD
V
DD
/2
C
S
R
F
Audio
Input
11 GAIN
IN–
R
I
13
V
1
O
O
C
I
14 IN+
1 W
C
B
V
2
V
DD
15
BYPASS
5
R
PU
NC
HP-IN1
6
7
3
2
1, 4, 8, 9, 16
HP-IN2
Bias
Control
HP-SENSE
SHUTDOWN
Headphone
Plug
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 2000, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPA4860
1-W MONO AUDIO POWER AMPLIFIER
SLOS164A – SEPTEMBER 1996 – REVISED MARCH 2000
AVAILABLE OPTIONS
PACKAGED DEVICE
T
A
SMALL OUTLINE
(D)
–40°C to 85°C
TPA4860D
†
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage, V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V
DD
Input voltage, V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to V +0.3 V
I
DD
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . internally limited (See Dissipation Rating Table)
Operating free-air temperature range, T
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to 85°C
A
Storage temperature range, T
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
stg
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
DISSIPATION RATING TABLE
PACKAGE
T
A
≤ 25°C
DERATING FACTOR
T
A
= 70°C
T = 85°C
A
D
1250 mW
10 mW/°C
800 mW
650 mW
recommended operating conditions
MIN
MAX
5.5
2.7
4.5
85
UNIT
V
Supply voltage, V
DD
2.7
1.25
1.25
–40
V
V
= 3.3 V
= 5 V
V
DD
Common-mode input voltage, V
IC
V
DD
Operating free-air temperature, T
°C
A
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPA4860
1-W MONO AUDIO POWER AMPLIFIER
SLOS164A – SEPTEMBER 1996 – REVISED MARCH 2000
electrical characteristics at specified free-air temperature range, V
noted)
= 3.3 V (unless otherwise
DD
TPA4860
UNIT
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
V
Output offset voltage (measured differentially)
Supply ripple rejection ratio
See Note 1
5
20
mV
dB
mA
µA
µA
V
OO
V
DD
= 3.2 V to 3.4 V
75
I
I
I
Quiescent current
2.5
750
0.6
1.7
1.7
2.8
0.2
DD
Quiescent current, mute mode
Quiescent current, shutdown mode
High-level input voltage (HP-IN)
Low-level input voltage (HP-IN)
High-level output voltage (HP-SENSE)
Low-level output voltage (HP-SENSE)
DD(M)
DD(SD)
V
V
V
V
IH
V
IL
I
I
= 100 µA
2.5
V
OH
OL
O
= –100 µA
0.8
V
O
NOTE 1: At 3 V < V
< 5 V the dc output voltage is approximately V /2.
DD
DD
operating characteristics, V
= 3.3 V, T = 25°C, R = 8 Ω
DD
A
L
TPA4860
TYP
PARAMETER
TEST CONDITIONS
UNIT
MIN
MAX
THD = 0.2%, f = 1 kHz,
= 2
350
500
mW
mW
A
V
P
O
Output power, see Note 2
THD = 2%,
= 2
f = 1 kHz,
A
V
B
B
Maximum output power bandwidth
Unity-gain bandwidth
Gain = 10,
Open Loop
f = 1 kHz
f = 1 kHz
Gain = 2
THD = 2%
20
1.5
56
30
20
kHz
MHz
dB
OM
1
BTL
SE
Supply ripple rejection ratio
dB
V
n
Noise output voltage, see Note 3
µV
NOTES: 2. Output power is measured at the output terminals of the device.
3. Noise voltage is measured in a bandwidth of 20 Hz to 20 kHz.
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPA4860
1-W MONO AUDIO POWER AMPLIFIER
SLOS164A – SEPTEMBER 1996 – REVISED MARCH 2000
electrical characteristics at specified free-air temperature range, V
noted)
= 5 V (unless otherwise
DD
TPA4860
UNIT
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
V
Output offset voltage
See Note 1
= 4.9 V to 5.1 V
5
20
mV
dB
mA
µA
µA
V
OO
Supply ripple rejection ratio
Supply current
V
DD
70
I
I
I
3.5
750
0.6
2.5
2.5
2.8
0.2
DD
Supply current, mute
DD(M)
Supply current, shutdown
DD(SD)
V
V
V
V
High-level input voltage (HP-IN)
Low-level input voltage (HP-IN)
High-level output voltage (HP-SENSE)
Low-level output voltage (HP-SENSE)
IH
V
IL
I
I
= 500 µA
2.5
V
OH
OL
O
= –500 µA
0.8
V
O
NOTE 1: At 3 V < V
< 5 V the dc output voltage is approximately V /2.
DD
DD
operating characteristic, V
= 5 V, T = 25°C, R = 8 Ω
A L
DD
TPA4860
TYP
PARAMETER
TEST CONDITIONS
UNIT
MIN
MAX
THD = 0.2%, f = 1 kHz,
1000
1100
mW
mW
A
V
= 2
P
O
Output power, see Note 2
THD = 2%,
= 2
f = 1 kHz,
THD = 2%
A
V
B
B
Maximum output power bandwidth
Unity-gain bandwidth
Gain = 10,
Open Loop
f = 1 kHz
f = 1 kHz
Gain = 2
20
1.5
56
30
20
kHz
MHz
dB
OM
1
BTL
SE
Supply ripple rejection ratio
dB
V
n
Noise output voltage, see Note 3
µV
NOTES: 2. Output power is measured at the output terminals of the device.
3. Noise voltage is measured in a bandwidth of 20 Hz to 20 kHz.
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPA4860
1-W MONO AUDIO POWER AMPLIFIER
SLOS164A – SEPTEMBER 1996 – REVISED MARCH 2000
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
1,2
V
OO
Output offset voltage
Distribution
I
Supply current distribution
vs Free-air temperature
3,4
DD
5,6,7,8,9,
10,11,15,
16,17,18
vs Frequency
THD+N
Total harmonic distortion plus noise
12,13,14,
19,20,21
vs Output power
I
Supply current
vs Supply voltage
vs Frequency
22
23,24
25
DD
V
Output noise voltage
Maximum package power dissipation
Power dissipation
n
vs Free-air temperature
vs Output power
vs Free-air temperature
vs Load Resistance
vs Supply Voltage
vs Frequency
26,27
28
Maximum output power
29
Output power
30
Open loop frequency response
Supply ripple rejection ratio
31
vs Frequency
32,33
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPA4860
1-W MONO AUDIO POWER AMPLIFIER
SLOS164A – SEPTEMBER 1996 – REVISED MARCH 2000
TYPICAL CHARACTERISTICS
DISTRIBUTION OF TPA4860
OUTPUT OFFSET VOLTAGE
DISTRIBUTION OF TPA4860
OUTPUT OFFSET VOLTAGE
25
20
15
10
5
25
20
15
10
5
V
CC
= 5 V
V
CC
= 3.3 V
0
0
–3 –2 –1
0
1
2
3
4
5
6
7
–3 –2 –1
0
1
2
3
4
5
6
7
V
OO
– Output Offset Voltage – mV
V
OO
– Output Offset Voltage – mV
Figure 1
Figure 2
SUPPLY CURRENT DISTRIBUTION
vs
SUPPLY CURRENT DISTRIBUTION
vs
FREE-AIR TEMPERATURE
FREE-AIR TEMPERATURE
3.5
4.5
4
V
CC
= 5 V
V
CC
= 3.3 V
3
2.5
2
3.5
3
2.5
2
Typical
Typical
1.5
1.5
1
0.5
0
1
0.5
0
–20
25
85
–20
25
85
T
A
– Free-Air Temperature – °C
T
A
– Free-Air Temperature – °C
Figure 3
Figure 4
6
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPA4860
1-W MONO AUDIO POWER AMPLIFIER
SLOS164A – SEPTEMBER 1996 – REVISED MARCH 2000
TYPICAL CHARACTERISTICS
TOTAL HARMONIC DISTORTION PLUS NOISE
TOTAL HARMONIC DISTORTION PLUS NOISE
vs
vs
FREQUENCY
FREQUENCY
10
10
V
P
= 5 V
= 1 W
= –10 V/V
= 8 Ω
DD
O
V
P
= 5 V
DD
O
= 1 W
= –2 V/V
= 8 Ω
A
V
A
V
R
L
R
L
1
1
C
= 0.1 µF
B
C
= 0.1 µF
B
C
= 1 µF
B
0.1
0.1
C
= 1 µF
B
0.01
0.01
20
100
1 k
10 k 20 k
20
100
1 k
10 k 20 k
f – Frequency – Hz
f – Frequency – Hz
Figure 5
Figure 6
TOTAL HARMONIC DISTORTION PLUS NOISE
TOTAL HARMONIC DISTORTION PLUS NOISE
vs
vs
FREQUENCY
FREQUENCY
10
10
V
P
= 5 V
= 1 W
= –20 V/V
= 8 Ω
V
P
= 5 V
DD
O
DD
O
= 0.5 W
= –2 V/V
= 8 Ω
A
A
V
V
C
= 0.1 µF
B
R
R
L
L
1
1
C
= 1 µF
B
C
= 0.1 µF
B
0.1
0.1
C
= 1 µF
B
0.01
0.01
20
100
1 k
10 k 20 k
20
100
1 k
10 k 20 k
f – Frequency – Hz
f – Frequency – Hz
Figure 7
Figure 8
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPA4860
1-W MONO AUDIO POWER AMPLIFIER
SLOS164A – SEPTEMBER 1996 – REVISED MARCH 2000
TYPICAL CHARACTERISTICS
TOTAL HARMONIC DISTORTION PLUS NOISE
TOTAL HARMONIC DISTORTION PLUS NOISE
vs
vs
FREQUENCY
FREQUENCY
10
10
V
P
= 5 V
V
P
= 5 V
DD
O
DD
O
= 0.5 W
= –10 V/V
= 8 Ω
= 0.5 W
= –20 V/V
= 8 Ω
A
A
V
V
R
R
C
= 0.1 µF
L
L
B
C
= 0.1 µF
B
1
1
C
= 1 µF
B
0.1
0.1
C
= 1 µF
B
0.01
0.01
20
100
1 k
10 k 20 k
20
100
1 k
10 k 20 k
f – Frequency – Hz
f – Frequency – Hz
Figure 9
Figure 10
TOTAL HARMONIC DISTORTION PLUS NOISE
TOTAL HARMONIC DISTORTION PLUS NOISE
vs
vs
FREQUENCY
OUTPUT POWER
10
10
V
= 5 V
= –10 V/V
V
= 5 V
= –2 V/V
= 8 Ω
DD
DD
A
A
V
V
Single Ended
R
L
f = 20 Hz
1
1
R
P
= 8 Ω
= 250 mW
L
O
C
= 0.1 µF
B
C
= 1 µF
B
R
P
= 32 Ω
= 60 mW
L
O
0.1
0.1
0.01
0.01
20
100
1 k
10 k 20 k
0.02
0.1
– Output Power – W
1
2
f – Frequency – Hz
P
O
Figure 11
Figure 12
8
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPA4860
1-W MONO AUDIO POWER AMPLIFIER
SLOS164A – SEPTEMBER 1996 – REVISED MARCH 2000
TYPICAL CHARACTERISTICS
TOTAL HARMONIC DISTORTION PLUS NOISE
TOTAL HARMONIC DISTORTION PLUS NOISE
vs
vs
OUTPUT POWER
OUTPUT POWER
10
10
V
= 5 V
= –2 V/V
= 8 Ω
V
= 5 V
= –2 V/V
= 8 Ω
DD
DD
A
A
V
V
R
R
L
L
f = 1 kHz
f = 20 kHz
C
= 0.1 µF
B
1
1
C
= 0.1 µF
B
0.1
0.1
0.01
0.01
0.02
0.1
1
2
0.02
0.1
1
2
P
O
– Output Power – W
P
O
– Output Power – W
Figure 13
Figure 14
TOTAL HARMONIC DISTORTION PLUS NOISE
TOTAL HARMONIC DISTORTION PLUS NOISE
vs
vs
FREQUENCY
FREQUENCY
10
10
V
P
R
= 3.3 V
= 350 mW
= 8 Ω
V
= 3.3 V
DD
DD
O
L
P
R
= 350 mW
= 8 Ω
L
O
A
V
= –2 V/V
A
V
= –10 V/V
1
1
C
= 0.1 µF
C = 0.1 µF
B
B
0.1
0.1
C
= 1 µF
C
= 1 µF
B
B
0.01
0.01
20
100
1 k
10 k 20 k
20
100
1 k
10 k 20 k
f – Frequency – Hz
f – Frequency – Hz
Figure 15
Figure 16
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPA4860
1-W MONO AUDIO POWER AMPLIFIER
SLOS164A – SEPTEMBER 1996 – REVISED MARCH 2000
TYPICAL CHARACTERISTICS
TOTAL HARMONIC DISTORTION PLUS NOISE
TOTAL HARMONIC DISTORTION PLUS NOISE
vs
vs
FREQUENCY
FREQUENCY
10
10
V
= 3.3 V
= –10 V/V
V
P
R
= 3.3 V
= 350 mW
= 8 Ω
DD
DD
O
L
A
V
Single Ended
A
V
= –20 V/V
C
= 0.1 µF
B
1
1
R
= 8 Ω
= 250 mW
L
P
O
R
= 32 Ω
= 60 mW
C
= 1 µF
B
L
0.1
0.1
P
O
0.01
0.01
20
100
1 k
10 k 20 k
20
100
1 k
10 k 20 k
f – Frequency – Hz
f – Frequency – Hz
Figure 17
Figure 18
TOTAL HARMONIC DISTORTION PLUS NOISE
TOTAL HARMONIC DISTORTION PLUS NOISE
vs
vs
OUTPUT POWER
OUTPUT POWER
10
10
V
= 3.3 V
= –2 V/V
= 8 Ω
V
= 3.3 V
= –2 V/V
= 8 Ω
DD
DD
A
A
V
V
R
R
L
L
f = 1 kHz
f = 20 Hz
1
1
C
= 0.1 µF
B
C
C
= 0.1 µF
B
0.1
0.1
= 1.0 µF
B
0.01
0.01
0.02
0.1
1
2
0.02
0.1
1
2
P
O
– Output Power – W
P
O
– Output Power – W
Figure 19
Figure 20
10
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPA4860
1-W MONO AUDIO POWER AMPLIFIER
SLOS164A – SEPTEMBER 1996 – REVISED MARCH 2000
TYPICAL CHARACTERISTICS
TOTAL HARMONIC DISTORTION PLUS NOISE
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
vs
OUTPUT POWER
10
5
4
3
2
1
0
T
A
= 0°C
T
A
= –20°C
C
= 0.1 µF
1
B
T = 25°C
A
T
A
= 85°C
0.1
V
= 3.3 V
= –2 V/V
= 8 Ω
DD
A
V
R
L
f = 20 kHz
0.01
20 m
0.1
1
2
2.5
3
3.5
4
4.5
5
5.5
P
O
– Output Power – W
V
DD
– Supply Voltage – V
Figure 21
Figure 22
OUTPUT NOISE VOLTAGE
OUTPUT NOISE VOLTAGE
vs
vs
FREQUENCY
FREQUENCY
3
10
2
10
1
10
1
3
2
1
1
10
10
10
V
CC
= 3.3 V
V
CC
= 5 V
V 1 +V 2
0
0
V 2
V 1 +V 2
V 2
0
0
0
0
V 1
0
V 1
0
20
100
1 k
10 k 20 k
20
100
1 k
10 k 20 k
f – Frequency – Hz
f – Frequency – Hz
Figure 23
Figure 24
11
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPA4860
1-W MONO AUDIO POWER AMPLIFIER
SLOS164A – SEPTEMBER 1996 – REVISED MARCH 2000
TYPICAL CHARACTERISTICS
MAXIMUM PACKAGE POWER DISSIPATION
POWER DISSIPATION
vs
vs
FREE-AIR TEMPERATURE
OUTPUT POWER
1.5
1.5
V
DD
= 5 V
1.25
R
= 4 Ω
L
1
1
0.75
R
= 8 Ω
L
0.5
0.25
0
0.5
R
= 16 Ω
L
0
–25
0
25
50
75 100 125 150 175
0
0.25
0.5
0.75
1
1.25
1.5
1.75
T
A
– Free-Air Temperature – °C
P
O
– Output Power – W
Figure 25
Figure 26
POWER DISSIPATION
vs
OUTPUT POWER
MAXIMUM OUTPUT POWER
vs
FREE-AIR TEMPERATURE
1
160
140
120
100
V
DD
= 3.3 V
R
= 16 Ω
L
0.75
0.5
R
= 4 Ω
= 8 Ω
L
80
60
40
R
= 8 Ω
L
R
L
0.25
0
R
= 4 Ω
L
20
0
R
= 16 Ω
L
0
0.25
0.5
0.75
0
0.25
0.5
0.75
1
1.25
1.50
P
O
– Output Power – W
P
O
– Maximum Output Power – W
Figure 27
Figure 28
12
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPA4860
1-W MONO AUDIO POWER AMPLIFIER
SLOS164A – SEPTEMBER 1996 – REVISED MARCH 2000
TYPICAL CHARACTERISTICS
OUTPUT POWER
vs
LOAD RESISTANCE
OUTPUT POWER
vs
SUPPLY VOLTAGE
1.4
1.2
1
2
A
= –2 V/V
V
A
= –2 V/V
V
f = 1 kHz
= 0.1 µF
f = 1 kHz
= 0.1 µF
1.75
C
B
C
B
THD+n ≤ 1%
THD+n ≤ 1%
1.5
1.25
1
R
= 4 Ω
L
0.8
0.6
R
= 8 Ω
L
V
CC
= 5 V
0.75
0.4
0.2
0
0.5
0.25
0
R
= 16 Ω
L
V
= 3.3 V
CC
4
8
12 16 20 24 28 32 36 40 44 48
2.5
3
3.5
4
4.5
5
5.5
Load Resistance – Ω
Supply Voltage – V
Figure 29
Figure 30
SUPPLY RIPPLE REJECTION RATIO
vs
FREQUENCY
OPEN LOOP FREQUENCY RESPONSE
0
100
45°
0°
V
R
= 5 V
= 8 Ω
V
R
C
= 5 V
= 8 Ω
= 0.1 µF
DD
L
DD
L
B
–10
–20
–30
–40
–50
Bridge Tied
Load
80
60
40
–45°
–90°
Phase
C
C
= 0.1 µF
= 1 µF
B
–60
–70
–80
Gain
B
20
0
–135°
–180°
–225°
–90
–100
–20
100
1 k
10 k 20 k
10
100
1 k
10 k
100 k
1 M
10 M
f – Frequency – Hz
f – Frequency – Hz
Figure 31
Figure 32
13
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPA4860
1-W MONO AUDIO POWER AMPLIFIER
SLOS164A – SEPTEMBER 1996 – REVISED MARCH 2000
TYPICAL CHARACTERISTICS
SUPPLY RIPPLE REJECTION RATIO
vs
FREQUENCY
0
V
R
= 5 V
DD
= 8 Ω
–10
–20
–30
–40
–50
L
Single Ended
C
= 0.1 µF
B
C
= 1 µF
B
–60
–70
–80
–90
–100
100
1 k
10 k 20 k
f – Frequency – Hz
Figure 33
APPLICATION INFORMATION
bridged-tied load versus single-ended mode
Figure 34 shows a linear audio power amplifier (APA) in a bridge tied load (BTL) configuration. A BTL amplifier
actually consists of two linear amplifiers driving both ends of the load. There are several potential benefits to
this differential drive configuration but initially let us consider power to the load. The differential drive to the
speaker means that as one side is slewing up the other side is slewing down and vice versa. This in effect
doubles the voltage swing on the load as compared to a ground referenced load. Plugging twice the voltage
into the power equation, where voltage is squared, yields 4 times the output power from the same supply rail
and load impedance (see equation 1).
V
O(PP)
V
(rms)
2
2
2
V
(rms)
(1)
Power
R
L
14
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPA4860
1-W MONO AUDIO POWER AMPLIFIER
SLOS164A – SEPTEMBER 1996 – REVISED MARCH 2000
APPLICATION INFORMATION
bridged-tied load versus single-ended mode (continued)
V
DD
V
O(PP)
2x V
R
O(PP)
L
V
DD
–V
O(PP)
Figure 34. Bridge-Tied Load Configuration
In a typical computer sound channel operating at 5 V, bridging raises the power into a 8-Ω speaker from a
singled-ended (SE) limit of 250 mW to 1 W. In sound power, that is a 6-dB improvement which is loudness that
canbeheard. Inadditiontoincreasedpowertherearefrequencyresponseconcerns, considerthesingle-supply
SEconfigurationshowninFigure35. Acouplingcapacitorisrequiredtoblockthedcoffsetvoltagefromreaching
the load. These capacitors can be quite large (approximately 40 µF to 1000 µF) so they tend to be expensive,
occupy valuable PCB area, and have the additional drawback of limiting low-frequency performance of the
system. This frequency limiting effect is due to the high pass filter network created with the speaker impedance
and the coupling capacitance and is calculated with equation 2.
1
(2)
f
c
2 R C
L
C
For example, a 68-µF capacitor with an 8-Ω speaker would attenuate low frequencies below 293 Hz. The BTL
configuration cancels the dc offsets, which eliminates the need for the blocking capacitors. Low-frequency
performance is then limited only by the input network and speaker response. Cost and PCB space are also
minimized by eliminating the bulky coupling capacitor.
V
DD
V
O(PP)
C
C
V
O(PP)
R
L
Figure 35. Single-Ended Configuration
15
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPA4860
1-W MONO AUDIO POWER AMPLIFIER
SLOS164A – SEPTEMBER 1996 – REVISED MARCH 2000
APPLICATION INFORMATION
bridged-tied load versus single-ended mode (continued)
Increasing power to the load does carry a penalty of increased internal power dissipation. The increased
dissipation is understandable considering that the BTL configuration produces 4 times the output power of the
SE configuration. Internal dissipation versus output power is discussed further in the thermal considerations
section.
BTL amplifier efficiency
Linear amplifiers are notoriously inefficient. The primary cause of these inefficiencies is voltage drop across the
output stage transistors. There are two components of the internal voltage drop. One is the headroom or dc
voltage drop that varies inversely to output power. The second component is due to the sinewave nature of the
output. The total voltage drop can be calculated by subtracting the RMS value of the output voltage from V
.
DD
The internal voltage drop multiplied by the RMS value of the supply current, I rms, determines the internal
DD
power dissipation of the amplifier.
An easy to use equation to calculate efficiency starts out as being equal to the ratio of power from the power
supply to the power delivered to the load. To accurately calculate the RMS values of power in the load and in
the amplifier, the current and voltage waveform shapes must first be understood (see Figure 36).
I
V
O
DD
I
DD(RMS)
V
(LRMS)
Figure 36. Voltage and Current Waveforms for BTL Amplifiers
Although the voltages and currents for SE and BTL are sinusoidal in the load, currents from the supply are very
different between SE and BTL configurations. In an SE application the current waveform is a half-wave rectified
shape, whereas in BTL it is a full-wave rectified waveform. This means RMS conversion factors are different.
Keep in mind that for most of the waveform both the push and pull transistor are not on at the same time, which
supports the fact that each amplifier in the BTL device only draws current from the supply for half the waveform.
The following equations are the basis for calculating amplifier efficiency.
16
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPA4860
1-W MONO AUDIO POWER AMPLIFIER
SLOS164A – SEPTEMBER 1996 – REVISED MARCH 2000
APPLICATION INFORMATION
P
L
Efficiency
(3)
P
SUP
Where:
V
P
V rms
L
2
2
2
V
V rms
L
p
P
L
R
2R
L
L
V
2V
DD
P
P
V
I
rms
SUP
DD DD
R
L
2V
P
I
rms
DD
R
L
1 2
P R
L
L
2
(4)
V
P
Efficiency of a BTL Configuration
2V
2V
DD
DD
NO TAG employs equation 4 to calculate efficiencies for four different output power levels. Note that the
efficiency of the amplifier is quite low for lower power levels and rises sharply as power to the load is increased,
resulting in a nearly flat internal power dissipation over the normal operating range. Note that the internal
dissipation at full output power is less than in the half power range. Calculating the efficiency for a specific
systemisthekeytoproperpowersupplydesign. Forastereo1-Waudiosystemwith8-Ω loadsanda5-Vsupply,
the maximum draw on the power supply is almost 3.25 W.
Table 1. Efficiency vs Output Power in 5-V 8-Ω BTL Systems
PEAK-TO-PEAK
VOLTAGE
(V)
INTERNAL
DISSIPATION
(W)
OUTPUT POWER
(W)
EFFICIENCY
(%)
0.25
0.50
1.00
1.25
31.4
44.4
62.8
70.2
2.00
2.83
4.00
0.55
0.62
0.59
0.53
†
4.47
†
High peak voltages cause the THD to increase.
A final point to remember about linear amplifiers whether they are SE or BTL configured is how to manipulate
the terms in the efficiency equation to utmost advantage when possible. Note that in equation 4, V is in the
DD
denominator. This indicates that as V
goes down, efficiency goes up.
DD
For example, if the 5-V supply is replaced with a 10-V supply (TPA4860 has a maximum recommended V
DD
of 5.5 V) in the calculations of NO TAG then efficiency at 1 W would fall to 31% and internal power dissipation
would rise to 2.18 W from 0.59 W at 5 V. Then for a stereo 1-W system from a 10-V supply, the maximum draw
would be almost 6.5 W. Choose the correct supply voltage and speaker impedance for the application.
17
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPA4860
1-W MONO AUDIO POWER AMPLIFIER
SLOS164A – SEPTEMBER 1996 – REVISED MARCH 2000
APPLICATION INFORMATION
selection of components
Figure 37 is a schematic diagram of a typical notebook computer application circuit.
50 kΩ
50 kΩ
V
12
10
C
DD
F
V
DD
= 5 V
C
S
V
/2
DD
R
F
Audio
Input
11 GAIN
IN–
R
I
13
V
1
O
O
C
I
46 kΩ
46 kΩ
1 W
14 IN+
Internal
Speaker
C
B
V
2
15
BYPASS
5
V
DD
R
PU
NC
HP-IN1
HP-IN2
6
7
3
2
1, 4, 8, 9, 16
Bias
Control
HP-SENSE
SHUTDOWN
Headphone
Plug
Figure 37. TPA4860 Typical Notebook Computer Application Circuit
gain setting resistors, R and R
F
I
The gain for the TPA4860 is set by resistors R and R according to equation 5.
F
I
R
F
Gain
2
(5)
R
I
BTL mode operation brings about the factor of 2 in the gain equation due to the inverting amplifier mirroring the
voltage swing across the load. Given that the TPA4860 is a MOS amplifier, the input impedance is very high,
consequently input leakage currents are not generally a concern although noise in the circuit increases as the
value of R increases. In addition, a certain range of R values is required for proper startup operation of the
F
F
amplifier. Taken together it is recommended that the effective impedance seen by the inverting node of the
amplifier be set between 5 kΩ and 20 kΩ. The effective impedance is calculated in equation 6.
R R
F I
Effective Impedance
(6)
R
R
F
I
As an example, consider an input resistance of 10 kΩ and a feedback resistor of 50 kΩ. The gain of the amplifier
would be –10 and the effective impedance at the inverting terminal would be 8.3 kΩ, which is well within the
recommended range.
18
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPA4860
1-W MONO AUDIO POWER AMPLIFIER
SLOS164A – SEPTEMBER 1996 – REVISED MARCH 2000
APPLICATION INFORMATION
gain setting resistors, R and R (continued)
F
I
Forhighperformanceapplicationsmetalfilmresistorsarerecommendedbecausetheytendtohavelowernoise
levels than carbon resistors. For values of R above 50 kΩ the amplifier tends to become unstable due to a pole
F
formed from R and the inherent input capacitance of the MOS input structure. For this reason, a small
F
compensation capacitor of approximately 5 pF should be placed in parallel with R . This, in effect, creates a low
F
pass filter network with the cutoff frequency defined in equation 7.
1
2 R C
f
(7)
c(lowpass)
F
F
For example, if R is 100 kΩ and Cf is 5 pF then f is 318 kHz, which is well outside of the audio range.
F
c
input capacitor, C
I
In the typical application an input capacitor, C , is required to allow the amplifier to bias the input signal to the
I
proper dc level for optimum operation. In this case, C and R form a high-pass filter with the corner frequency
I
I
determined in equation 8.
1
f
(8)
c(highpass)
2 R C
I
I
The value of C is important to consider as it directly affects the bass (low frequency) performance of the circuit.
I
Consider the example where R is 10 kΩ and the specification calls for a flat bass response down to 40 Hz.
I
Equation 8 is reconfigured as equation 9.
1
C
(9)
I
2 R f
c
I
In this example, C is 0.40 µF, so one would likely choose a value in the range of 0.47 µF to 1 µF. A further
I
consideration for this capacitor is the leakage path from the input source through the input network (R , C ) and
I
I
thefeedbackresistor(R )totheload. Thisleakagecurrentcreatesadcoffsetvoltageattheinputtotheamplifier
F
that reduces useful headroom, especially in high gain applications. For this reason a low-leakage tantalum or
ceramic capacitor is the best choice. When polarized capacitors are used, the positive side of the capacitor
should face the amplifier input in most applications as the dc level there is held at V /2, which is likely higher
DD
that the source dc level. Note that it is important to confirm the capacitor polarity in the application.
power supply decoupling, C
S
The TPA4860 is a high-performance CMOS audio amplifier that requires adequate power supply decoupling
to ensure the output total harmonic distortion (THD) is as low as possible. Power supply decoupling also
prevents oscillations for long lead lengths between the amplifier and the speaker. The optimum decoupling is
achieved by using two capacitors of different types that target different types of noise on the power supply leads.
For higher frequency transients, spikes, or digital hash on the line, a good low equivalent-series-resistance
(ESR) ceramic capacitor, typically 0.1 µF placed as close as possible to the device V
filtering lower-frequency noise signals, a larger aluminum electrolytic capacitor of 10 µF or greater placed near
lead, works best. For
DD
the power amplifier is recommended.
19
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPA4860
1-W MONO AUDIO POWER AMPLIFIER
SLOS164A – SEPTEMBER 1996 – REVISED MARCH 2000
APPLICATION INFORMATION
midrail bypass capacitor, C
B
The midrail bypass capacitor, C , serves several important functions. During start-up or recovery from
B
shutdown mode, C determines the rate at which the amplifier starts up. This helps to push the start-up pop
B
noise into the subaudible range (so low it can not be heard). The second function is to reduce noise produced
by the power supply caused by coupling into the output drive signal. This noise is from the midrail generation
circuit internal to the amplifier. The capacitor is fed from a 25-kΩ source inside the amplifier. To keep the start-up
pop as low as possible, the relationship shown in equation 10 should be maintained.
1
1
(10)
C
25 kΩ
C R
I
B
I
As an example, consider a circuit where C is 0.1 µF, C is 0.22 µF and R is 10 kΩ. Inserting these values into
B
I
I
the equation 9 we get: 400 ≤ 454 which satisfies the rule. Bypass capacitor, C , values of 0.1 µF to 1 µF ceramic
B
or tantalum low-ESR capacitors are recommended for the best THD and noise performance.
single-ended operation
Figure 38 is a schematic diagram of the recommended SE configuration. In SE mode configurations, the load
should be driven from the primary amplifier output (OUT1, terminal 10).
V
DD
12
V
DD
= 5 V
C
S
V
DD
/2
R
F
Audio
Input
11 GAIN
IN–
R
I
C
C
13
V
V
1
2
10
15
O
250-mW
External
Speaker
C
I
14 IN+
C
B
R
= 50 Ω
SE
O
BYPASS
5
C
= 0.1 µF
SE
Figure 38. Singled-Ended Mode
Gain is set by the R and R resistors and is shown in equation 11. Since the inverting amplifier is not used to
F
I
mirror the voltage swing on the load, the factor of 2 is not included.
R
F
Gain
(11)
R
I
The phase margin of the inverting amplifier into an open circuit is not adequate to ensure stability, so a
termination load should be connected to V 2. This consists of a 50-Ω resistor in series with a 0.1-µF capacitor
O
to ground. It is important to avoid oscillation of the inverting output to minimize noise and power dissipation.
20
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPA4860
1-W MONO AUDIO POWER AMPLIFIER
SLOS164A – SEPTEMBER 1996 – REVISED MARCH 2000
APPLICATION INFORMATION
single-ended operation (continued)
The output coupling capacitor required in single-supply SE mode also places additional constraints on the
selection of other components in the amplifier circuit. The rules described earlier still hold with the addition of
the following relationship:
1
1
1
(12)
R C
C
25 kΩ
C R
I
L C
B
I
output coupling capacitor, C
C
In the typical single-supply SE configuration, an output coupling capacitor (C ) is required to block the dc bias
C
at the output of the amplifier thus preventing dc currents in the load. As with the input coupling capacitor, the
output coupling capacitor and impedance of the load form a high-pass filter governed by equation 13.
1
2 R C
f
(13)
c high
L
C
The main disadvantage, from a performance standpoint, is that the load impedances are typically small, which
drives the low-frequency corner higher. Large values of C are required to pass low frequencies into the load.
C
Consider the example where a C of 68 µF is chosen and loads vary from 8 Ω, 32 Ω, to 47 kΩ. Table 2
C
summarizes the frequency response characteristics of each configuration.
Table 2. Common Load Impedances vs Low Frequency Output Characteristics in SE Mode
R
C
LOWEST FREQUENCY
L
C
8 Ω
68 µF
68 µF
68 µF
293 Hz
73 Hz
32 Ω
47,000 Ω
0.05 Hz
As Table 2 indicates, most of the bass response is attenuated into 8-Ω loads while headphone response is
adequate and drive into line level inputs (a home stereo for example) is very good.
headphone sense circuitry, R
pu
The TPA4860 is commonly used in systems where there is an internal speaker and a jack for driving external
loads (i.e., headphones). In these applications, it is usually desirable to mute the internal speaker(s) when the
externalloadisinuse. Theheadphoneinputs(HP-1, HP-2)andheadphoneoutput(HP-SENSE)oftheTPA4860
were specifically designed for this purpose. Many standard headphone jacks are available with an internal
single-pole single-throw (SPST) switch that makes or breaks a circuit when the headphone plug is inserted.
Asserting either or both HP-1 and/or HP-2 high mutes the output stage of the amplifier and causes HP-SENSE
to go high. In battery-powered applications where power conservation is critical HP-SENSE can be connected
to the shutdown input as shown in Figure 39. This places the amplifier in a very low current state for maximum
power savings. Pullup resistors in the range from 1 kΩ to 10 kΩ are recommended for 5-V and 3.3-V operation.
21
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPA4860
1-W MONO AUDIO POWER AMPLIFIER
SLOS164A – SEPTEMBER 1996 – REVISED MARCH 2000
APPLICATION INFORMATION
V
DD
R
PU
NC
HP-IN1
6
7
3
HP-IN2
Bias
Control
HP-SENSE
SHUTDOWN
Headphone
Plug
2
Figure 39. Schematic Diagram of Typical Headphone Sense Application
Table 3 details the logic for the mute function of the TPA4860.
Table 3. Truth Table for Headphone Sense and Shutdown Functions
†
OUTPUT
HP-SENSE
Low
INPUTS
HP-2
Low
AMPLIFIER
STATE
HP-1
Low
Low
High
High
X
SHUTDOWN
Low
Active
Mute
High
Low
Low
High
Low
High
Mute
High
X
Low
High
Mute
High
X
Shutdown
†
Inputs should never be left unconnected.
X = do not care
shutdown mode
The TPA4860 employs a shutdown mode of operation designed to reduce quiescent supply current, I
, to
DD(q)
the absolute minimum level during periods of nonuse for battery-power conservation. For example, during
device sleep modes or when other audio-drive currents are used (i.e., headphone mode), the speaker drive is
not required. The SHUTDOWN input terminal should be held low during normal operation when the amplifier
is in use. Pulling SHUTDOWN high causes the outputs to mute and the amplifier to enter a low-current state,
I
<1µA. SHUTDOWNshouldneverbeleftunconnectedbecauseamplifieroperationwouldbeunpredictable.
DD
using low-ESR capacitors
Low-ESR capacitors are recommended throughout this applications section. A real capacitor can be modeled
simply as a resistor in series with an ideal capacitor. The voltage drop across this resistor minimizes the
beneficial effects of the capacitor in the circuit. The lower the equivalent value of this resistance the more the
real capacitor behaves like an ideal capacitor.
thermal considerations
A prime consideration when designing an audio amplifier circuit is internal power dissipation in the device. The
curve in Figure 40 provides an easy way to determine what output power can be expected out of the TPA4860
for a given system ambient temperature in designs using 5-V supplies. This curve assumes no forced airflow
or additional heat sinking.
22
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPA4860
1-W MONO AUDIO POWER AMPLIFIER
SLOS164A – SEPTEMBER 1996 – REVISED MARCH 2000
APPLICATION INFORMATION
160
140
120
100
V
DD
= 5 V
R
= 16 Ω
L
80
60
40
R
= 8 Ω
L
R
= 4 Ω
L
20
0
0
0.25
0.5
0.75
1
1.25
1.50
Maximum Output Power – W
Figure 40. Free-Air Temperature Versus Maximum Continuous Output Power
5-V versus 3.3-V operation
The TPA4860 was designed for operation over a supply range of 2.7 V to 5.5 V. This data sheet provides full
specifications for 5-V and 3.3-V operation, as these are considered to be the two most common standard
voltages. There are no special considerations for 3.3-V versus 5-V operation as far as supply bypassing, gain
setting, or stability. Supply current is slightly reduced from 3.5 mA (typical) to 2.5 mA (typical). The most
important consideration is that of output power. Each amplifier in TPA4860 can produce a maximum voltage
swing of V
– 1 V. This means, for 3.3-V operation, clipping starts to occur when V
= 4 V while operating at 5 V. The reduced voltage swing subsequently reduces maximum output
= 2.3 V as opposed
DD
O(PP)
to when V
O(PP)
power into an 8-Ω load to less than 0.33 W before distortion begins to become significant.
Operation at 3.3-V supplies, as can be shown from the efficiency formula in equation 4, consumes
approximately two-thirds the supply power for a given output-power level than operation from 5-V supplies.
When the application demands less than 500 mW, 3.3-V operation should be strongly considered, especially
in battery-powered applications.
23
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPA4860
1-W MONO AUDIO POWER AMPLIFIER
SLOS164A – SEPTEMBER 1996 – REVISED MARCH 2000
MECHANICAL INFORMATION
D (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0.050 (1,27)
0.020 (0,51)
0.014 (0,35)
0.010 (0,25)
M
14
8
0.008 (0,20) NOM
0.244 (6,20)
0.228 (5,80)
0.157 (4,00)
0.150 (3,81)
Gage Plane
0.010 (0,25)
1
7
0°–8°
0.044 (1,12)
A
0.016 (0,40)
Seating Plane
0.004 (0,10)
0.010 (0,25)
0.004 (0,10)
0.069 (1,75) MAX
PINS **
8
14
16
DIM
0.197
(5,00)
0.344
(8,75)
0.394
(10,00)
A MAX
0.189
(4,80)
0.337
(8,55)
0.386
(9,80)
A MIN
4040047/D 10/96
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15).
D. Falls within JEDEC MS-012
24
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright 2000, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明