L294 [STMICROELECTRONICS]
SWITCH-MODE SOLENOID DRIVER; 开关式电磁驱动器
| 型号： | L294 |
| 厂家： | 
ST |
| 描述： | SWITCH-MODE SOLENOID DRIVER |
| 文件： | 总8页 (文件大小：118K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
L294
SWITCH-MODE SOLENOID DRIVER
HIGH VOLTAGE OPERATION (UP TO 50V)
HIGHOUTPUTCURRENTCAPABILITY(UPTO4A)
LOW SATURATION VOLTAGE
Multiwatt 11
TTL-COMPATIBLE INPUT
OUTPUT SHORT CIRCUIT PROTECTION (TO
GROUND, TO SUPPLY AND ACROSS THE
LOAD)
THERMAL SHUTDOWN
OVERDRIVING PROTECTION
LATCHED DIAGNOSTIC OUTPUT
ORDER CODE : L294
DESCRIPTION
feature of the L294 is a latched diagnostic output
which indicates when the output is short circuited.
The L294 is supplied in a 11-lead Multiwatt® plas-
tic power package.
The L294 is a monolithic switched mode solenoid
driver designed for fast, high current applications
such as hummer and needle driving in printers and
electronic typewriters. Power dissipation is re-
duced by efficient switchmode operation. An extra
BLOCK DIAGRAM
October 1991
1/8
L294
ABSOLUTE MAXIMUM RATING
Symbol
Parameter
Value
Unit
V
Vs
Power Supply Voltage
Logic Supply Voltage
Enable Voltage
50
VSS
VEN
Ip
7
V
7
4.5
V
Peak Output Current (repetitive)
A
Ptot
stg, Tj
25
W
°C
Total Power Dissipation (at Tcase = 75 °C)
Storage and Junction Temperature
T
- 40 to 150
CONNECTION DIAGRAM (top view)
THERMAL DATA
Symbol
Parameter
Thermal resistance junction-case
Value
Unit
°C/W
Rth-j-case
Max
3
2/8
L294
ELECTRICAL CHARACTERISTICS (refer to the test circuit, Vs = 40 V, Vss = 5V, Tamb = 25 °C, unless
otherwise specified)
Symbol
Parameter
Test conditions
Operative Condition
Min.
Typ. Max.
Unit
Vs
Id
Power Supply Voltage (pin 1)
Quiescent Drain Current (pin 1)
12
46
V
VENABLE = H
20
70
30
mA
Vi ≥ 0.6V; VENABLE = L
Vss
Iss
Logic Suply Voltage (pin 4)
4.5
0.6
7
8
V
mA
µA
V
V
DIAG = L
5
Quiescent Logic Supply
Current
DIAG Output at High Impedance
Operating Output
Non-operative Output
Vi ≥ 0.6V
10
100
Vi
Input Voltage (pin 7)
0.45
0.8
Ii
Input Current (pin 7)
-1
-3
µA
Vi ≤ 0.45V
VENABLE
IENABLE
Iload/ Vi
Enable Input Voltage (pin 9)
Enable Input Current (pin 9)
Trasconductance
Low Level
-0.3
2.4
V
High Level
VENABLE = L
-100
100
1.05
1.3
µA
VENABLE = H
Vi = 1V
Vi = 4V
0.95
0.97
1
1
RS = 0.2 Ω
A/V
V
Vsat H
Vsat L
Source Output Saturation
Voltage
Ip = 4A
1.7
Sink Output Saturation Voltage
Ip = 4A
Ip = 4A
2
V
V
Vsat H + VsatL Total Saturation Voltage
4.5
Ileakage
K
Output Leakage Current
1
mA
Rs = 0.2Ω; Vi ≤ 0.45 V
VENABLE = L
On Time Limiter Constant (°)
120
VDIAG
Diagnostic Output Voltage
(pin 5)
IDIAG = 10 mA
0.4
10
V
IDIAG
Diagnostic Leakage Current
(pin 5)
VDIAG = 40V
µA
V
pin 8
10
OP AMP and OTA CD Voltage
Gain (°°)
Vpin 10 = 100 to 800 mV
5
V
pin
VSENS
Sensing Voltage (pin 10) (°°°)
0.9
V
(°) After a time interval tmax = KC2, the output stages are disabled.
(°°) See the block diagram.
(°°°) Allowed range of VSENS without intervention of the short circuit protection.
3/8
L294
CIRCUIT OPERATION
The L294 work as a trasconductance amplifier: it
can supply an output current directly proportional
to an input voltage level (Vi). Fyrthermore, it allows
complete switching control of the output current
waveform (see fig. 1).
The following explanation refers to the Block Dia-
gram, to fig. 1 and to the typical application circuit
of fig. 2.
to t1. The peak current Ip depends on Vi as shown
in the typical transfer function of fig.3.
It can be seen that for Vi lower than 450 mV the
device is not operating.
For Vi greater than 600 mV, the L294 has a tran-
sconductance of 1A/V with Rs = 0.2Ω. For Vi in-
cluded between 450 and 600 mV, the operation is
not guaranteed.
The ton time is fixed by the width of the Enable input
signal (TTLcompatible): it is active low and enables
the output stages "source" and "sink". At the end of
ton, the load current Iload recirculates through D1
and D2, allowing fast current turn-off.
The rise time tr, depends on the load charac-
teristics, on Vi and on the supply voltage value (Vs,
pin 1). During the ton time, Iload is converter into a
voltage signal by means of the external sensing
resistance Rs connected to pin 10. This signal,
amplified by the op amp and converted by the
transconductance amplifier OTA, charges the ex-
ternal RC network at pin 8 (R1, C1). The voltage at
this pin is sensed by the inverting input of a com-
parator. The voltage on the non-inverting input of
this one is fixed by the external voltage Vi (pin 7).
After tr, the comparator switches and the output
stage "source" is switched off. The comaprator
output is confirmed by the voltage on the non-in-
verting input, which decreases of a costant fraction
of Vi (1/10), allowing hysteresis operation. The
current in the load now flow through D1.
Two Cases are possible: the time constant of the
recirculation phase is higher than R1.C1; the time
constant is lower than R1.C1. In the first case, the
voltage sensed in the non-inverting input of the
comparator is just the value proportional to Iload. In
the second case, when the current decreases too
quickly, the comparator senses the voltage signal
stored in the R1 C1 network.
The order parts of the device have protection and
diagnostic functions. At pin 3 is connected an ex-
ternal capacitor C2, charged at costant current
when the Enable is low.
After a time interval equal to K C2 (K is defined in
the table of Electrical Characteristics and has the
dimensions of ohms) the output stages are
switched off independently by the Input signal.
This avoids the load being driven in conduction for
an excessive period of time (overdriving protec-
tion). The action of this protection is shown in fig.
1b. Note that the voltage ramp at pin 3 starts
whenever the Enable signal becomes active (low
state), regardless of the Input signal. To reset pin 3
and to restore the normal conditions, pin 9 must
return high.
This protection can be disabled by grounding pin 3.
The thermal protection included in the L294 has a
hysteresis.
It switches off the output stages whenever the
junction temperature increases too much. After a
fall of about 20°C, the circuit starts again.
Finally, the device is protected against any type of
short circuit at the outputs: to ground, to supply and
across the load.
When the source stage current is higher than 5A
and/or when the pin 10 voltage is higher then 1V
(i.e. fora sinkcurrentgreater than 1V/Rs) theoutput
stages are switched off and the device is inhibited.
This condition is indicated at the open-collector
output DIAG (pin 5); the internal flip-flop F/F
changes and forces the output transistor into satu-
ration. The F/F must be supplied independently
through Vss (pin 4). The DIAG signal is reset and
the output stages are stilloperative by switching the
device on again. After that, two cases are possible:
the reason for the "bad operation" is still present
and the protection acts again; the reason has been
removed and the device starts to work properly.
In the first case t1 depends on the load charac-
teristics, while in the second case it depends only
on the value of R1. C1.
In the other words, R1. C1 fixes the minimum value
of t1 )t1 ≥ 1/10 R1.C1. Note that C1 should be
chosen in the range 2.7 to 10 nF for stability rea-
sons of the OTA).
After t1, the comparator switches again: the output
is confirmed by the voltage on the non-inverting
input, which reaches Vi again (hysteresis).
Now the cycle starts again: t2, t4 and t6 have the
same characteristics as tr, while t3 and t5 are similar
4/8
L294
Figure 1. Output Current Waveforms.
Figure 2. Test and Typical Application Circuit.
D1 : 3A fast diode
trr ≤
}
200 ns
Figure 3. Peak Output Current vs. Input
Voltage.
Figure 4. Output Saturation Voltage vs.
Peak Output Current.
5/8
L294
Figure 5. Safe Operating Areas.
Figure 6. Turn-off Phase.
CALCULATION OF THE SWITCHING TIMES
Referring to the block diagram and to the waveforms of fig. 1, it is possible to calculate the switching times
by means of the following relationships.
RL
V1
where : V1 = Vs - Vsat L - Vsat H _ VR sens
L
RL
L
tr = −
tf = −
In (1 −
• Ip )
V2
where : V2 = Vs + VD1 + VD2
In
RL
V2 + RL • Io
IK ≤ Io ≤ Ip
Io is the value of the load current at the end of ton.
t1 = t3 = t5 = ...
where
0.9 Ip • RL + V3
L
a) −
In
V3 = Vsat L + VR sens + VD1
Ip RL + V3
RL
=
1
b) − R1 C1 In 0.9
R1 C1
10
t2 = t4 = t6 = ...
V1 − Ip RL
L
RL
= −
In (
)
V1 − IK RL
Note that the time interval t1 = t3 = t5 = ... takes the longer value between case a) and case b). The switching
frequency is always :
1
fswitching
=
t
+ t2
1
In the case a) the main regulation loop is always closed and it forces :
IK = (0.9 ± S) Ip
where : S = 3 % @ Vi = 1 V
S = 1.5 % @ Vi = 4 V
In the case b), the same loop is open in the recirculation phase and IK, which is always lower than 0.9 Ip,
is obtained by means of the following relationship.
t1 RL
L
t1 RL
L
V3
RL
IK = Ip e −
−
(1 − e −
)
With the typical application circuit, in the conditions Vs = 40V, Ip = 4A, the following switching times result:
tr = 255 µs
tf = 174 µs @ Io = Ip
t2 = 29 µs
a) 70 µs
t1 =
6/8
b) 16 µs
f = 10.2 KHz
L294
MULTIWATT11 PACKAGE MECHANICAL DATA
mm
inch
TYP.
DIM.
MIN.
TYP.
MAX.
5
MIN.
MAX.
A
B
0.197
0.104
0.063
2.65
1.6
C
D
1
0.039
E
0.49
0.88
1.57
16.87
19.6
0.55
0.95
0.019
0.035
0.062
0.664
0.772
0.022
0.037
0.072
0.674
F
G
1.7
17
1.83
0.067
0.669
G1
H1
H2
L
17.13
20.2
22.3
22.2
18.1
17.75
10.9
2.9
0.795
0.878
0.874
0.713
0.699
0.429
0.114
0.177
0.209
0.102
0.102
0.152
21.5
21.4
17.4
17.25
10.3
2.65
4.1
0.846
0.843
0.685
0.679
0.406
0.104
0.161
0.192
0.075
0.075
0.144
L1
L2
L3
L4
L7
M
17.5
10.7
0.689
0.421
4.3
4.5
0.169
0.200
M1
S
4.88
1.9
5.08
5.3
2.6
S1
Dia1
1.9
2.6
3.65
3.85
7/8
L294
Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsibility for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No
license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned
in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied.
SGS-THOMSON Microelectronics products are not authorized for use as critical components in life support devices or systems without express
written approval of SGS-THOMSON Microelectronics.
© 1994 SGS-THOMSON Microelectronics - All Rights Reserved
SGS-THOMSON Microelectronics GROUP OF COMPANIES
Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands - Singapore -
Spain - Sweden - Switzerland - Taiwan - Thaliand - United Kingdom - U.S.A.
8/8
相关型号：
©2020 ICPDF网 联系我们和版权申明