SC653ULTRT [SEMTECH]
Light Management Unit with 2 LDOs and SemPulse®Interface; 有2个LDO和SemPulse®Interface照明管理单元型号: | SC653ULTRT |
厂家: | SEMTECH CORPORATION |
描述: | Light Management Unit with 2 LDOs and SemPulse®Interface |
文件: | 总22页 (文件大小:305K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
SC653
Light Management Unit with
2 LDOs and SemPulse® Interface
POWER MANAGEMENT
Features
Description
Input supply voltage range — 2.9V to 5.5V
Four programmable current sinks with 29 steps from
0mA to 25mA
Very high efficiency charge pump driver system with
three modes — 1x, 1.5x and 2x
The SC653 is a highly integrated light management unit
that provides two low-noise LDOs, a multi-mode high
efficiency charge pump, and four programmable LED
drivers. Performance is optimized for use in single-cell Li-
ion battery applications.
Two programmable 200mA low-noise LDO regulators
Charge pump frequency — 250kHz
SemPulse single wire interface
Backlight current accuracy — 1.5ꢀ typical
Backlight current matching — 0.5ꢀ typical
Fade-in/fade-out feature for main backlight
Automatic sleep mode (LEDs off) — IQ = 100μA
Shutdown current — 0.1μA (typical)
Ultra-thin package — 2.3 x 2.3 x 0.6 (mm)
Lead-free and halogen-free
The load and supply conditions determine whether the
charge pump operates in 1x, 1.5x, or 2x mode. A program-
mable fading feature can be enabled to gradually adjust
the backlight current, simplifying control software. The
low-dropout, low-noise linear regulators can be used for
powering a camera module or other peripheral circuits.
The SC653 uses the proprietary SemPulse single wire
®
interface. This interface controls all functions of the device,
including backlight currents and LDO voltage outputs.
The single wire interface minimizes microcontroller and
interface pin counts.
WEEE and RoHS compliant
Applications
Cellular phones, smart phones, and PDAs
LCD modules
Portable media players
Digital cameras and GPS units
Display backlighting and LED indicators
The SC653 enters sleep mode when all the LED drivers are
disabled. In this mode, the quiescent current is reduced
while the device continues to monitor the SemPulse inter-
face. The two LDOs can be enabled when the device is in
sleep mode.
Typical Application Circuit
MAIN BACKLIGHT
SC653
V
BAT = 2.9V to 5.5V
IN
OUT
SemPulse
Interface
COUT
2.2μF
SPIF
CIN
2.2μF
GND2
GND2
ENL1
ENL2
BL1
GND2
BL2
BL3
BL4
BYP
CBYP
22nF
VLDO1 = 1.5V to 3.3V
LDO1
GND1
GND2
VLDO2 = 1.2V to 1.8V
LDO2
C1+ C1- C2+ C2-
CLDO1
CLDO2
1μF
1μF
GND1
GND2
GND1
GND1
C1
2.2μF
C2
2.2μF
US Patents: 6,504,422; 6,794,926
1
October 21, 2009
© 2009 Semtech Corporation
SC653
Pin Configuration
Ordering Information
Device
Package
SC653ULTRT(1)(2)
SC653EVB
MLPQ-UT-18 2.3×2.3
Evaluation Board
18
17
16
15
14
Notes:
BYP
1
13
C2+
(1) Available in tape and reel only. A reel contains 3,000 devices.
(2) Lead-free packaging only. Device is WEEE and RoHS compliant,
and halogen-free.
TOP VIEW
12
11
C1+
C1-
BL1
BL2
2
3
T
7
BL3
10
C2-
4
5
6
8
9
MLPQ-UT-18; 2.3x2.3, 18 LEAD
θJA = 45°C/W
Marking Information
653
yyww
xxxx
yyww = date code
xxxx = Semtech Lot Number
2
SC653
Absolute Maximum Ratings
Recommended Operating Conditions
IN, OUT (V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to +6.0
C1+, C2+ (V) . . . . . . . . . . . . . . . . . . . . . . . -0.3 to (VOUT + 0.3)
Pin Voltage — All Other Pins (V) . . . . . . . . . -0.3 to (VIN + 0.3)
OUT — Short Circuit Duration . . . . . . . . . . . . . . Continuous
LDO1, LDO2 — Short Circuit Duration . . . . . . Continuous
ESD Protection Level(1) (kV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Ambient Temperature Range (°C) . . . . . . . . -40 ≤ TA ≤ +85
Input Voltage (V) . . . . . . . . . . . . . . . . . . . . . . . 2.9 ≤ VIN ≤ 5.5
Output Voltage (V) . . . . . . . . . . . . . . . . . . . . . 2.5 ≤ VOUT ≤ 5.25
Voltage Difference between any two LEDs (V). . ΔVF < 1.0(2)
Thermal Information
Thermal Resistance, Junction to Ambient(3) (°C/W) . . . . . . . 45
Maximum Junction Temperature (°C) . . . . . . . . . . . . . . .+150
Storage Temperature Range (°C). . . . . . . . . . . . -65 to +150
Peak IR Reflow Temperature (10s to 30s) (°C) . . . . . . . +260
Exceeding the above specifications may result in permanent damage to the device or device malfunction. Operation outside of the parameters
specified in the Electrical Characteristics section is not recommended.
NOTES:
(1) Tested according to JEDEC standard JESD22-A114.
(2) ΔVF(max) = 1.0V when VIN = 2.9V, higher VIN supports higher ΔVF(max)
(3) Calculated from package in still air, mounted to 3”x 4.5”, 4 layer FR4 PCB with thermal vias under the exposed pad per JESD51 standards.
Electrical Characteristics
Unless otherwise noted, TA = +25°C for Typ, -40ºC to +85°C for Min and Max, TJ(MAX) = 125ºC, VIN = 3.7V, CIN= C1= C2= 2.2μF,
C
OUT = 2.2μF (ESR = 0.03Ω), ΔVF ≤ 1.0V(1)
Parameter
Symbol
Conditions
Min
Typ
Max
Units
Supply Specifications
Shutdown Current
IQ(OFF)
Shutdown
0.1
100
220
3.8
2
μA
μA
(2)
Sleep (LDOs off), SPIF = VIN
Sleep (LDOs on), SPIF = VIN(2), ILDOn = 0mA
Charge pump in 1x mode, IOUT = 20mA, IBLn = 5mA
Charge pump in 1.5x mode, IOUT = 20mA, IBLn = 5mA
Charge pump in 2x mode, IOUT = 20mA, IBLn = 5mA
Total Quiescent Current
IQ
4.6
mA
4.6
Charge Pump Electrical Specifications
VIN > 3.2V, sum of all active LED currents,
Maximum Total Output Current
IOUT(MAX)
100
mA
V
OUT(MAX) = 4.2V
Backlight Current Setting
Backlight Current Accuracy
Backlight Current Matching
IBL
Nominal setting for BL1 thru BL4
IBLn = 12mA(3), TA = 25°C
IBLn = 12mA(4)
0.5
-8
25
+8
mA
ꢀ
IBL_ACC
IBL-BL
1.5
0.5
-3.5
+3.5
ꢀ
3
SC653
Electrical Characteristics (continued)
Parameter
Symbol
Conditions
Min
Typ
Max
Units
Charge Pump Electrical Specifications (continued)
1x Mode to 1.5x Mode
VTRANS1x
IOUT = 40mA, IBLn = 10mA, VOUT = 3.2V
IOUT = 40mA, IBLn = 10mA, VOUT = 3.2V
IOUT = 40mA, IBLn = 10mA, VOUT = 4.0V(5)
IOUT = 40mA, IBLn = 10mA, VOUT = 4.0V(5)
VIN = VBLn = 4.2V
3.27
250
2.92
300
0.1
V
Falling Transition Voltage
1.5x Mode to 1x Mode Hysteresis
VHYST1x
VTRANS1.5x
VHYST1.5x
IBLn
mV
V
1.5x Mode to 2x Mode
Falling Transition Voltage
2x Mode to 1.5x Mode Hysteresis
mV
μA
kHz
Current Sink Off-State
Leakage Current
1
Pump Frequency
fPUMP
VIN = 3.2V
250
LDO Electrical Specifications
LDO1 Voltage Setting
LDO2 Voltage Setting
VLDO1
VLDO2
Range of nominal settings in 100mV increments
Range of nominal settings in 100mV increments
ILDOn = 1mA, TA = 25°C, 2.9V ≤ VIN ≤ 4.2V
ILDOn = 1mA to 100mA, 2.9V ≤ VIN ≤ 4.2V
ILDO1 = 1mA, VOUT = 2.8V
1.5
1.2
-3
3.3
1.8
+3
V
V
ꢀ
ꢀ
LDO1, LDO2 Output
Voltage Accuracy
ΔVLDO
ΔVLINE
ΔVLOAD
-3.5
3
2.1
1.3
+3.5
7.2
4.8
25
Line Regulation
mV
ILDO2 = 1mA, VOUT = 1.8V
VLDO1 = 3.3V, ILDO1 = 1mA to 100 mA
VLDO2 = 1.8V, ILDO2 = 1mA to 100 mA
Load Regulation
mV
mV
20
Dropout Voltage(6)
VD
ILDO1 = 150mA
150
55
200
1.5V < VLDO1 < 3.0V, f < 1kHz, CBYP = 22nF,
PSRRLDO1
I
LDO1 = 50mA with 0.5VP-P supply ripple
Power Supply Rejection Ratio
dB
1.2V < VLDO2, f < 1kHz, CBYP = 22nF, ILDO2 = 50mA,
with 0.5VP-P supply ripple
PSRRLDO2
60
LDO1, 10Hz < f < 100kHz, CBYP = 22nF, CLDOn = 1μF,
en-LDO1
100
ILDO1 = 50 mA, 1.5V < VLDO1 < 3.0V
Output Voltage Noise
μVRMS
μF
LDO2, 10Hz < f < 100kHz, CBYP = 22nF, CLDO = 1μF,
en-LDO2
50
1
I
LDO2 = 50 mA
Minimum Output Capacitor
CLDO(MIN)
4
SC653
Electrical Characteristics (continued)
Parameter
Symbol
Conditions
Min
Typ
Max
Units
Digital I/O Electrical Specifications (SPIF, ENL1, ENL2)
Input High Threshold(7)
Input Low Threshold(7)
Input High Current
Input Low Current
VIH
VIL
IIH
VIN = 5.5V
VIN = 3.0V
VIN = 5.5V
VIN = 5.5V
1.6
V
V
0.4
+1
+1
-1
-1
μA
μA
IIL
SemPulse Electrical Specifications (SPIF)
SemPulse Start-up Time(8)
Bit Pulse Duration(7)
Duration Between Bits(7)
Hold Time - Address(7)
Hold Time - Data(7)
tSU
1
ms
μs
tHI
tLO
0.75
0.75
500
500
10
250
250
μs
tHOLDA
tHOLDD
tBR
SPIF is held high
SPIF is held high
SPIF is held high
SPIF is pulled low
5000
μs
μs
Bus Reset Time(7)
ms
ms
Shutdown Time(9)
tSD
10
Fault Protection
Output Short Circuit Current Limit
LDO Current Limit
IOUT(SC)
ILIM
OUT pin shorted to GND
VLDOn enabled
250
mA
mA
°C
200
5.3
TOTP
THYS
Rising threshold
Hysteresis
165
30
Over-Temperature
°C
Charge Pump
Over-Voltage Protection
OUT pin open circuit, VOUT = VOVP
rising threshold
VOVP
5.7
6.0
V
VUVLO-OFF
VUVLO-HYS
Increasing VIN
Hysteresis
2.7
V
Under Voltage Lockout
Notes:
800
mV
(1) ΔVF is the voltage difference between any two LEDs.
(2) SPIF is high for more than 10ms
(3) Subscript n = 1 and 2 for the LDOs, and n = 1, 2, 3, and 4 for the backlights.
(4) Current matching equals ꢁIBL(MAX) - IBL(MIN] / ꢁIBL(MAX) + IBL(MIN)].
(5) Test voltage is VOUT = 4.0V — a relatively extreme LED voltage — to force a transition during test. Typically VOUT = 3.2V for white LEDs.
(6) Dropout is defined as (VIN -VLDO1) whenVLDO1 drops 100mV from nominal. Dropout does not apply to LDO2 since it has a maximum output voltage
of 1.8V.
(7) The source driver used to provide the SemPulse output must meet these limits.
(8) The SemPulse start-up time is the minimum time that the SPIF pin must be held high to enable the part before starting communication.
(9) The SemPulse shutdown time is the minimum time that the SPIF pin must be pulled low to shut the part down.
5
SC653
Typical Characteristics
Battery Current (4 LEDs) — 25mA Each
Backlight Efficiency (4 LEDs) — 25mA Each
VOUT = 3.56V, IOUT = 100mA, 25°C
VOUT = 3.56V, IOUT = 100mA, 25°C
180
160
140
120
100
80
100
90
80
70
60
50
4.2
3.9
3.6
3.3
3
2.7
4.2
3.9
3.6
3.3
3
2.7
V
IN(V)
VIN(V)
Backlight Efficiency (4 LEDs) — 12mA Each
Battery Current (4 LEDs) — 12mA Each
VOUT = 3.41V, IOUT = 48mA, 25°C
VOUT = 3.41V, IOUT = 48mA, 25°C
90
80
70
60
50
40
100
90
80
70
60
50
3
4.2
3.9
3.6
3.3
2.7
4.2
3.9
3.6
3.3
3
2.7
VIN(V)
VIN(V)
Battery Current ( 4 LEDs) — 5.0mA Each
Backlight Efficiency ( 4 LEDs) — 5.0mA Each
VOUT = 3.27V, IOUT = 20mA, 25°C
VOUT = 3.27V, IOUT = 20mA, 25°C
50
40
30
20
10
0
100
90
80
70
60
50
3
3.9
2.7
4.2
3.9
3.6
3.3
2.7
4.2
3.6
3.3
3
VIN(V)
VIN(V)
6
SC653
Typical Characteristics (continued)
PSRR vs. Frequency — 1.8V
VIN = 3.7V, IOUT = 50mA, TA = 25°C
PSRR vs. Frequency — 2.8V
VIN = 3.7V, IOUT = 50mA, TA = 25°C
0
0
-10
-20
-30
-40
-50
-60
-70
-10
-20
-30
-40
-50
-60
-70
10
1000
10000
100
10
100
10000
1000
Frequency (Hz)
Frequency (Hz)
Line Regulation (LDO2)
ILDO1 = 1mA, VLDO1 = 1.2V and 1.8V, 25°C
Line Regulation (LDO1)
ILDO1 = 1mA, VLDO1 = 2.8V, 25°C
1.5
1
3
2
1
0.5
0
1.2V
1.8V
0
2.8V
-1
-2
-3
-0.5
-1
-1.5
4.2
3
3.3
2.7
3.9
3.6
3.3
2.7
4.2
3.9
3.6
3
VIN(V)
VIN(V)
LDO Noise vs. Load Current — 1.8V
LDO Noise vs. Load Current — 2.8V
VLDO=1.8V, VIN=3.7V, 25°C, 10Hz < f < 100kHz
VLDO=2.8V, VIN=3.7V, 25°C, 10Hz < f < 100kHz
100
80
60
40
20
0
100
80
60
40
20
0
0
20
40
60
80
100
0
30
60
90
120
150
IOUT (mA)
IOUT (mA)
7
SC653
Typical Characteristics (continued)
Load Regulation (LDO2)
Load Regulation (LDO1)
VIN = 3.7V, 25°C
0
VIN=3.7V, 25°C
0
-5
-5
1.5V
1.2V
-10
-15
-20
-10
1.8V
1.5V
2.5V
-15
1.8V
2.8V
-20
-25
-30
-35
3.3V
-25
-30
200
0
40
80
120
160
0
40
80
120
160
200
ILDO (mA)
ILDO (mA)
LDO Load Transient Response (1.2V)
VIN=3.7V, VLDO=1.2V, ILDO=1 to 100mA, 25°C
LDO Load Transient Response (3.3V)
VIN=3.7V, VLDO=3.3V, ILDO=1 to 100mA, 25°C
VLDO (50mV/div)
VLDO (50mV/div)
ILDO (100mA/div)
ILDO (100mA/div)
Time (20μs/div)
Time (20μs/div)
LDO Load Transient Response (1.8V)
VIN=3.7V, VLDO=1.8V, ILDO=1 to 100mA, 25°C
Output Short Circuit Current Limit
VOUT=0V, VIN=4.2V, 25°C
VOUT (1V/div)
VLDO (50mV/div)
ILDO (100mA/div)
IOUT (200mA/div)
Time (20μs/div)
Time (1ms/div)
8
SC653
Typical Characteristics (continued)
Ripple — 1.5X Mode
VIN=2.9V, 4 Backlights — 25 mA each, 25°C
Ripple — 1X Mode
VIN=3.7V, 4 Backlights — 25 mA each, 25°C
VIN (100mV/div)
VIN (100mV/div)
V
OUT (100mV/div)
IBL (20mA/div)
V
OUT (100mV/div)
IBL (20mA/div)
Time (20μs/div)
Time (20μs/div)
Output Open Circuit Protection
Ripple — 2X Mode
VIN=2.9V, 4 Backlights — 25 mA each, 25°C
VIN=3.7V, 25°C
VBL (500mV/div)
VIN (100mV/div)
5.42V
VOUT (1V/div)
VOUT (100mV/div)
IBL (20mA/div)
IBL (20mA/div)
Time (20μs/div)
Time (200μs/div)
9
SC653
Pin Descriptions
Pin #
Pin Name
Pin Function
1
2
3
4
5
BYP
BL1
BL2
BL3
BL4
Bypass pin for voltage reference — ground CBYP to GND1 on ground island.
Current sink output for main backlight LED 1 — leave this pin open if unused
Current sink output for main backlight LED 2 — leave this pin open if unused
Current sink output for main backlight LED 3 — leave this pin open if unused
Current sink output for main backlight LED 4 — leave this pin open if unused
SemPulse single wire interface pin — used to enable/disable the device and to configure all regis-
ters (refer to Register Map and SemPulse Interface sections)
6
SPIF
7
GND1
ENL1(1)
ENL2 (2)
C2-
Ground pin — Ground CBYP, CLDO1, CLDO2 to GND1 on ground island.
LDO1 enable input — active high
8
9
LDO2 enable input — active high
10
11
12
13
14
15
Negative connection to bucket capacitor 2
Negative connection to bucket capacitor 1
Positive connection to bucket capacitor 1
Positive connection to bucket capacitor 2
Charge pump output — all LED anode pins should be connected to this pin
Battery voltage input
C1-
C1+
C2+
OUT
IN
16
GND2
Ground Pin — connect to ground plane
17
18
LDO1
LDO2
Output of LDO1 — ground CLDO1 to GND1 on ground island.
Output of LDO2 — ground CLDO2 to GND1 on ground island.
Thermal pad for heatsinking purposes — connect to ground plane using multiple vias. This pad is
internally connected to ground and to pins 7 and 16.
T
THERMAL PAD
NOTES:
(1) ENL1 must be high for the SPIF interface to control LDO1. When low, ENL1 disables LDO1.
(2) ENL2 must be high for the SPIF interface to control LDO2. When low, ENL2 disables LDO2.
10
SC653
Block Diagram
C1+
12
C1-
11
C2+
13
C2-
10
VIN
14 OUT
Fractional Charge Pump
(1x, 1.5x, 2x)
IN 15
6
SPIF
Oscillator
SemPulseTM
Digital
2
3
4
5
BL1
BL2
BL3
BL4
Interface
and Logic
Control
Current
Setting
DAC
Bandgap
Reference
BYP
1
7
Voltage
Setting
DAC
VIN
GND1
LDO1
17 LDO1
8
9
ENL1
ENL2
VIN
LDO2
18 LDO2
GND2
16
11
SC653
Applications Information
Note that small package capacitors can decrease in value
by up to 50ꢀ under DC loading, so it is strongly recom-
mended that 2.2uF capacitors be selected when using
0402 size ceramic capacitors. The device also requires a
2.2μF capacitor on the IN pin and a 2.2μF capacitor on
the OUT pin to minimize noise and support the output
drive requirements. Capacitors with X7R or X5R ceramic
dielectric are strongly recommended for their low ESR
and superior temperature and voltage characteristics.
Y5V capacitors should not be used as their temperature
coefficients make them unsuitable for this application.
General Description
This design is optimized for handheld applications sup-
plied from a single Li-Ion cell and includes the following
key features:
• A high efficiency fractional charge pump that
supplies power to all LEDs
• Four matched current sinks that control LED
backlighting current, with 0mA to 25mA per
LED
• Two adjustable LDOs with outputs ranging from
1.5V to 3.3V for LDO1 and 1.2V to 1.8V for LDO2,
adjustable in 100mV increments
LED Backlight Current Sinks
The backlight current is set via the SemPulse interface.
The current is regulated to one of 29 values between
0mA and 25mA. The step size varies depending upon the
current setting. The step sizes are 0.5mA for current set-
tings between 0mA and 5mA. The step size increases to
1mA for settings between 5mA and 21mA. Steps are 2mA
between 21mA and 25mA. The variation in step size
allows finer adjustment for dimming functions in the low
current setting range and coarse adjustment at higher
current settings where small current changes are not
visibly noticeable in LED brightness. A zero setting is also
included to allow the current sink to be disabled by
writing to either the enable bit or the current setting reg-
ister for maximum flexibility.
High Current Fractional Charge Pump
The backlight outputs are supported by a high efficiency,
high current fractional charge pump output at the OUT
pin. The charge pump multiplies the input voltage by 1,
1.5, or 2 times. The charge pump switches at a fixed fre-
quency of 250kHz in 1.5x and 2x modes and is disabled in
1x mode to save power and improve efficiency.
The mode selection circuit automatically selects the mode
as 1x, 1.5x, or 2x based on circuit conditions such as LED
voltage, input voltage, and load current. The 1x mode is
the most efficient of the three modes, followed by 1.5x
and 2x modes. Circuit conditions such as low input voltage,
high output current, or high LED voltage place a higher
demand on the charge pump output. A higher numerical
mode (1.5x or 2x) may be needed momentarily to main-
tain regulation at the OUT pin during intervals of high
demand. The charge pump responds to momentary high
demands, setting the charge pump to the optimum mode
to deliver the output voltage and load current while opti-
mizing efficiency. Hysteresis is provided to prevent mode
toggling.
All backlight current sinks have matched currents, even
when there is variation in the forward voltages (ΔVF ) of
the LEDs. A ΔVF of 1.2V is supported when the input
voltage is at 3.0V. Higher ΔVF LED mis-match is supported
when VIN is higher than 3.0V. All current sink outputs are
compared and the lowest output is used for setting the
voltage regulation at the OUT pin. This is done to ensure
that sufficient bias exists for all LEDs.
The charge pump requires two bucket capacitors for
proper operation. One capacitor must be connected
between the C1+ and C1- pins and the other must be con-
nected between the C2+ and C2- pins as shown in the
typical application circuit diagram. These capacitors
should be equal in value, with a nominal capacitance of
1.0μF to support the charge pump current requirements.
The backlight LEDs default to the off state upon power-
up. For backlight applications using less than four LEDs,
any unused output must be left open and the unused
LED driver must remain disabled. When writing to the
Backlight Enable register, a zero (0) must be written to
the corresponding bit of any unused output.
12
SC653
Applications Information (continued)
Backlight Quiescent Current
Immediate
change to new
bright level
The quiescent current required to operate all four back-
lights is reduced by 1.5mA when backlight current is set
to 4.0mA or less. This feature results in higher efficiency
under light-load conditions. Further reduction
in quiescent current will result from using fewer than four
LEDs.
No change
FADE=0
Write new
bright level
Write FADE=0
FADE=0
Write
FADE=1
Immediate
change to
new bright
level
Write
FADE=0
FADE=1
Fade-In and Fade-Out
No
The SC653 contains bits that control the fade state of the
main bank. When enabled, the fade function causes the
backlight settings to step from their current state to the
next programmed state as soon as the new state is stored
in its register. For example, if the backlight is set at 25mA
and the next setting is the off state, the backlight will step
from 25mA down to 0mA using all 29 settings at the fade
rate specified by the bits in register 04h. The same is true
when turning on or increasing the backlight current —
the backlight current will step from the present level to
the new level at the step rate defined in register 04h. This
process applies for both the main and the sub displays.
change
FADE=1
Write
FADE=1
Write new
bright
Fade=0
level
Fade
begins
Fade
ends
Fade is redirected
toward the new
value from current
state
Fade
processing(1)
No
change
Write new
bright level
Write
Fade=1
Write
Continue
fade using
new rate
new fade
rate
Note:
The fade rate may be changed dynamically when a fade
operation is active by writing new values to the fade reg-
ister. When a new backlight level is written during an
ongoing fade operation, the fade will be redirected to the
new value from the present state. An ongoing fade opera-
tion may be cancelled by disabling fade which will result
in the backlight current changing immediately to the final
value. If fade is disabled, the current level will change
immediately without the fade delay. The state diagram in
Figure 1 describes all possible conditions for a fade opera-
tion. More details can be found in the Register Map
Section.
(1) When the data in backlight
enable register 01h is not 00h
Figure 1 — Fade State Diagram
Programmable LDO Outputs
Two low dropout (LDO) regulators are provided for
camera module I/O and core power. Each LDO output
voltage setting has 3.5ꢀ accuracy over the operating
temperature range. Output current greater than the
specification is possible at somewhat reduced accuracy.
Input pins ENL1 and ENL2 may be used to directly enable
and disable the LDOs without communication via the
SPIF interface. When power is first applied to the SC653,
the register defaults reset the LDOs to the off state, so
SPIF must be used one time to set the voltages before
ENL1 and ENL2 can be used to enable the LDOs.
13
SC653
Applications Information (continued)
To control LDOs exclusively by software, ENL1 and ENL2
may be permanently terminated to the battery voltage.
ENL1 must be high for the SPIF interface to control LDO1.
When low, ENL1 disables LDO1. ENL2 is used exactly the
same way to enable and disable LDO2.
Output Open Circuit Protection
Over-Voltage Protection (OVP) is provided at the OUT pin
to prevent the charge pump from producing an exces-
sively high output voltage. In the event of an open circuit
at OUT, the charge pump runs in open loop and the
voltage rises up to the OVP limit. OVP operation is hyster-
etic, meaning the charge pump will momentarily turn off
until VOUT is sufficiently reduced. The maximum OVP
threshold is 6.0V, allowing the use of a ceramic output
capacitor rated at 6.3V.
A 1μF, low ESR capacitor should be used as a bypass
capacitor on each LDO output to reduce noise and ensure
stability. In addition, it is recommended that a nominal
minimum 22nF capacitor be connected between the BYP
pin and the GND1 pin to minimize noise and achieve
optimum power supply rejection. A larger capacitor can
be used for this function, but at the expense of increasing
turn-on time. Capacitors with X7R or X5R ceramic dielec-
tric are strongly recommended for their low ESR and
superior temperature and voltage characteristics. Y5V
capacitors should not be used as their temperature coef-
ficients make them unsuitable for this application.
Over-Temperature Protection
The Over-Temperature (OT) protection circuit prevents the
device from overheating and experiencing a catastrophic
failure. When the junction temperature exceeds 165°C, the
device goes into thermal shutdown with all outputs dis-
abled until the junction temperature is reduced. All regis-
ter information is retained during thermal shutdown.
Hysteresis of 30°C is provided to ensure that the device
cools sufficiently before re-enabling.
Shutdown Mode
The device is disabled when the SPIF pin is held low for
the shutdown time specified in the electrical characteris-
tics section. All registers are reset to default condition at
shutdown. Typical current consumption in this mode is
0.1μA.
Charge Pump Output Current Limit
The device limits the charge pump current at the OUT pin.
When OUT is shorted to ground, the output current will
typically equal 250mA. The output current is also limited
to 250mA when over-loaded resistively.
Sleep Mode
LDO Current Limit
When all LEDs are disabled, sleep mode is activated. This
is a reduced current mode that helps minimize overall
current consumption by disabling the clock and the
charge pump while continuing to monitor the serial
interface for commands. The two LDOs can be enabled
when the device is in sleep mode.
The device limits the output currents of LDO1 and LDO2
to help prevent the device from overheating and to
protect the loads. The minimum limit is 200mA, so load
current greater than the rated current and up to 200mA
can be used with degraded accuracy and larger dropout
without tripping the current limit.
Protection Features
LED Float Detection
The SC653 provides several protection features to safe-
guard the device from catastrophic failures. These fea-
tures include:
Float detect is a fault detection feature of the LED current
sink outputs. If an output is programmed to be enabled
and an open circuit fault occurs at any current sink output,
that output will be disabled to prevent a sustained output
OVP condition from occurring due to the resulting open
loop. Float detect ensures device protection but does not
ensure optimum performance. Unused LED outputs must
be disabled to prevent an open circuit fault from
occurring.
• Output Open Circuit Protection
• Over-Temperature Protection
• Charge Pump Output Current Limit
• LDO Current Limit
• LED Float Detection
14
SC653
Applications Information (continued)
• The following capacitors — CLDO1, CLDO2, and
PCB Layout Considerations
CBYP should be grounded together through an
isolated copper island. Using no vias, connect
the island only, to pin 7 as shown in Figure 2.
• Figure 3 shows only the vias that should be con-
nected to the ground plane with multiple vias.
• Make all ground connections to a solid ground
plane as shown in Figure 4.
The layout diagram in Figure 2 illustrates a proper
two-layer PCB layout for the SC653 and supporting com-
ponents. Following fundamental layout rules is critical for
achieving the performance specified in the Electrical
Characteristics table. The following guidelines
are recommended when developing a PCB layout:
• Place all bucket, bypass, and decoupling capaci-
tors — C1, C2, CIN, COUT, CLDO1, CLDO2, and
CBYP as close to the device as possible.
• All charge pump current passes through IN,
OUT, and the bucket capacitor connection pins.
Ensure that all connections to these pins make
use of wide traces so that the resistive drop on
each connection is minimized.
• All LDO output traces should be made as wide
as possible to minimize resistive losses.
• The thermal pad should be connected to the
ground plane using multiple vias to ensure
proper thermal connection for optimal heat
transfer.
CLDO2
CLDO1
17
CIN
COUT
Figure 3 — Layer 1
Vias to
ground
plane
IN OUT
CBYP
18
16 15
14
1
13
GND2
12
11
2
3
SC653
C1
C2
10
4
5
6
7
8
9
Keep gap
open
Island for
pin 7 GND1
(no vias)
Ground Layer
Figure 4 — Layer 2
Figure 2 — Recommended PCB Layout
15
SC653
SemPulse Interface
Introduction
®
held high for tHOLDD when the pulse train is completed. If
the proper hold time is not received, the interface will
keep counting pulses until the hold time is detected. If
the total exceeds 63 pulses, the write will be ignored and
the bus will reset after the next valid hold time is detected.
After the bus has been held high for tHOLDD, the bus will
expect the next pulse set to be an address write. Note
that this is the same effect as the bus reset that occurs
when tHOLDA exceeds its maximum specification. For this
reason, there is no maximum limit on tHOLDD — the bus
simply waits for the next valid address to be transmitted.
SemPulse is a write-only single wire interface. It provides
access to up to 32 registers that control device functional-
ity. Two sets of pulse trains are transmitted via the SPIF
pin. The first pulse set is used to set the desired address.
After the bus is held high for the address hold period, the
next pulse set is used to write the data value. After the
data pulses are transmitted, the bus is held high again for
the data hold period to signify the data write is complete.
At this point the device latches the data into the address
that was selected by the first set of pulses. See the
SemPulse Timing Diagrams for descriptions of all timing
parameters.
Multiple Writes
It is important to note that this single-wire interface
requires the address to be paired with its corresponding
data. If it is desired to write multiple times to the same
address, the address must always be re-transmitted prior
to the corresponding data. If it is only transmitted one
time and followed by multiple data transmissions, every
other block of data will be treated like a new address. The
result will be invalid data writes to incorrect addresses.
Note that multiple writes only need to be separated by
the minimum tHOLDD for the slave to interpret them cor-
rectly. As long as tHOLDA between the address pulse set and
the data pulse set is less than its maximum specification
but greater than its minimum, multiple pairs of address
and data pulse counts can be made with no detrimental
effects.
Chip Enable/Disable
The device is enabled when the SemPulse interface pin
(SPIF) is pulled high for greater than tSU. If the SPIF pin is
pulled low again for more than tSD, the device will be
disabled.
Address Writes
The first set of pulses can range between 0 and 31 (or 1 to
32 rising edges) to set the desired address. After the
pulses are transmitted, the SPIF pin must be held high for
t
HOLDA to notify the slave device that the address write is
finished. If the pulse count is between 0 and 31 and the
line is held high for tHOLDA, the address is latched as the
destination for the data word. If the SPIF pin is not held
high for tHOLDA, the slave device will continue to count
pulses. If the total exceeds 31 pulses, the write will be
ignored and the bus will reset after the next valid hold
time is detected. Note that if tHOLDA exceeds its maximum
specification, the bus will reset. This means that the com-
munication is ignored and the bus resumes monitoring
the pin, expecting the next pulse set to be an address.
Standby Mode
Once data transfer is completed, the SPIF line must be
returned to the high state for at least 10ms to return to the
standby mode. In this mode, the SPIF line remains idle
while monitoring for the next command. This mode
allows the device to minimize current consumption
between commands. Once the device has returned to
standby mode, the bus is automatically reset to expect the
address pulses as the next data block. This safeguard is
intended to reset the bus to a known state (waiting for the
beginning of a write sequence) if the delay exceeds the
reset threshold.
Data Writes
After the bus has been held high for the minimum
address hold period, the next set of pulses are used to
write the data value. The total number of pulses can
range from 0 to 63 (or 1 to 64 rising edges) since there are
a total of 6 register bits per register. Just like with the
address write, the data write is only accepted if the bus is
16
SC653
SemPulse Interface (continued)
®
The SemPulse single wire interface is used to enable or disable the device and configure all registers (see Figure 2). The
timing parameters refer to the digital I/O electrical specifications.
Address is set
Up to 32 rising edges
(0 to 31 pulses)
Up to 64 rising edges
(0 to 63 pulses)
Data is written
SPIF
t = tSU
t = tHOLDA
t = tHOLDD
tHI
tLO
Figure 2 — Uniform Timing Diagram for SemPulse Communication
Timing Example 1
In this example (see Figure 3), the slave chip receives a sequence of pulses to set the address and data, and the pulses
experience interrupts that cause the pulse width to be non-uniform. Note that as long as the maximum high and low
times are satisfied and the hold times are within specification, the data transfer is completed regardless of the number
of interrupts that delay the transmission.
Address is set to
register 02h
Data written is
000011
SPIF
tLO
t = tSU
tHI
t = tHOLDA
t = tHOLDD
t < tHImax
t < tLOmax
Figure 3 — SemPulse Data Write with Non-Uniform Pulse Widths
Timing Example 2
In this example (see Figure 4), the slave chip receives two sets of pulses to set the address and data, but an interrupt
occurs during a pulse that causes it to exceed the minimum address hold time. The write is meant to be the value 03h
in register 05h, but instead it is interpreted as the value 02h written to register 02h. The extended pulse that is delayed
by the interrupt triggers a false address detection, causing the next pulse set to be interpreted as the data set. To avoid
any problems with timing, make sure that all pulse widths comply with their timing requirements as outlined in this
datasheet.
Address is set to register
03h (address and data are
now out of order)
Address is set to
register 02h
Data written is
000010
SPIF
Interrupt
duration
t > tHImax
t = tHOLDA
t = tHOLDD
Figure 4 — Faulty SemPulse Data Write Due to Extended Interrupt Duration
17
SC653
Register Map(1)
Reset
Value
Address
00h
D5
0(2)
0(2)
D4
BL_4
0(2)
D3
BL_3
D2
BL_2
D1
BL_1
D0
BL_0
Description
Backlight
Current
00h
00h
Backlight
Enable
01h
BLEN_4
BLEN_3
BLEN_2
BLEN_1
02h
03h
04h
0(2)
0(2)
0(2)
0(2)
0(2)
0(2)
LDO1_3
0(2)
LDO1_2
LDO2_2
FADE_1
LDO1_1
LDO2_1
FADE_0
LDO1_0
LDO2_0
FADE_EN
00h
00h
00h
LDO1
LDO2
Fade
0(2)
Notes:
(1) All registers are write-only.
(2) 0 = always write a 0 to these bits
Definition of Registers and Bits
Backlight
Current (mA)
BL_4 BL_3 BL_2 BL_1 BL_0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
4
4.5
5
BL Current Control Register (00h)
This register is used to set the currents for the backlight
current sinks. These current sinks need to be enabled in
the Backlight Enable Control register to be active.
6
7
BL[D4:D0]
8
These bits are used to set the current for the backlight
current sinks. All enabled backlight current sinks will sink
the same current, as shown in Table 1.
9
10
11
12
13
14
15
16
17
18
19
20
21
23
25
Table 1 — Backlight Current Settings
Backlight
BL_4 BL_3 BL_2 BL_1 BL_0
Current (mA)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
0
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
1
0
1
0
0
See note 1
See note 1
See note 1
0.5
1
1.5
2
2.5
3
(1) Reserved for future use
3.5
18
SC653
Register and Bit Definitions (continued)
Backlight Enable Control Register (01h)
This register is used to enable the backlight current
sinks.
LDO2 Control Register (03h)
This register is used to enable the LDO2 and to set the
output voltage VLDO2
.
BLEN[D4:D1]
LDO2[D2:D0]
These bits are used to enable current sinks (active high,
These bits are used to set the output voltage, VLDO2, as
default low).
shown in Table 3.
Table 3 — LDO2 Control Bits
BLEN_4 — Enable bit for backlight BL4
BLEN_3 — Enable bit for backlight BL3
BLEN_2 — Enable bit for backlight BL2
BLEN_1 — Enable bit for backlight BL1
LDO2_2
LDO2_1
LDO2_0
VLDO2
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
OFF
1.8V
1.7V
1.6V
1.5V
1.4V
1.3V
1.2V
When enabled, the current sinks will carry the current set
by the backlight current control bits BLꢁ4:0], as shown in
Table 1.
LDO1 Control Register (02h)
This register is used to enable LDO1 and set the output
voltage VLDO1
.
LDO1[D3:D0]
Fade Control Register (04h)
This register is used to enable the backlight fade and to
set the rise and fall rate at which fading proceeds.
These bits set the output voltage, VLDO1, as shown in
Table 2.
Table 2 — LDO1 Control Bits
FADE[D2:D1]
These bits are used to set the rise/fall rate between two
backlight currents as shown in Table 4.
LDO1_3 LDO1_2 LDO1_1 LDO1_0
VLDO1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
OFF
3.3V
3.2V
3.1V
3.0V
2.9V
2.8V
2.7V
2.6V
2.5V
2.4V
2.2V
1.8V
1.7V
1.6V
1.5V
Table 4 — Fade Control Bits
Fade Feature Rise/Fall Rate
FADE_1
FADE_0
(ms/step)
0
0
1
1
0
1
0
1
32
24
16
8
The number of steps in changing the backlight current
will be equal to the change in binary count of bits
BLꢁ4:0].
19
SC653
Register and Bit Definitions (continued)
FADE_EN [D0]
This bit is used to enable or disable the fade feature. When
the fade function is enabled and a new backlight current
is set, the backlight current will change from its current
value to a new value set by bits BLꢁ4:0] at a rate of 8ms to
32ms per step. A new backlight level cannot be written
during an ongoing fade operation, but an ongoing fade
operation may be cancelled by resetting the fade bit.
Clearing the fade bit during an ongoing fade operation
changes the backlight current immediately to the value of
BLꢁ4:0]. The number of counts to complete a fade opera-
tion equals the difference between the old and new
backlight values to increment or decrement the BLꢁ4:0]
bits. If the fade bit is cleared, the current level will change
immediately without the fade delay. The rate of fade may
be changed dynamically, even while a fade operation is
active, by writing new values to the FADE_1 and FADE_0
bits. The total fade time is determined by the number of
steps between old and new backlight values, multiplied
by the rate of fade in ms/step. The longest elapsed time
for a full scale fade-out of the backlight is nominally 938ms
when the default interval of 32ms is used.
20
SC653
Outline Drawing — MLPQ-UT-18 2.3x2.3
A
D
B
E
DIMENSIONS
MILLIMETERS
DIM
MIN
0.50
0.00
NOM MAX
-
-
A
A1
A2
b
0.60
0.05
PIN 1
INDICATOR
(LASER MARK)
(0.152)
0.20
2.30
1.20
2.30
1.20
0.40 BSC
0.30
18
0.15
2.20
1.15
2.20
1.15
0.25
2.40
1.25
2.40
1.25
D
D1
E
E1
e
A2
C
L
N
0.25
0.35
A
SEATING
PLANE
aaa C
aaa
0.08
0.10
bbb
A1
D1
LxN
E/2
E1
2
1
e/2
N
bxN
bbb
C A B
e
D/2
NOTES:
1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES).
2.
COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS.
21
SC653
Land Pattern — MLPQ-UT-18 2.3x2.3
K
DIMENSIONS
MILLIMETERS
R
DIM
(2.33)
1.76
1.20
1.20
0.40
0.10
0.20
0.57
2.90
C
G
H
K
P
R
X
Y
Z
(C)
H
Z
G
Y
X
P
NOTES:
1.
2.
CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES).
THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY.
CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR
COMPANY'S MANUFACTURING GUIDELINES ARE MET.
3.
THERMAL VIAS IN THE LAND PATTERN OF THE EXPOSED PAD
SHALL BE CONNECTED TO A SYSTEM GROUND PLANE.
FAILURE TO DO SO MAY COMPROMISE THE THERMAL AND/OR
FUNCTIONAL PERFORMANCE OF THE DEVICE.
4. SQUARE PACKAGE-DIMENSIONS APPLY IN BOTH X AND Y DIRECTIONS.
Contact Information
Semtech Corporation
Power Management Products Division
200 Flynn Road, Camarillo, CA 93012
Phone: (805) 498-2111 Fax: (805) 498-3804
www.semtech.com
22
相关型号:
©2020 ICPDF网 联系我们和版权申明