HYS64T32900EDL-3.7-B2 [QIMONDA]
200-Pin SO-DIMM DDR2 SDRAM Modules; 200针SO -DIMM DDR2 SDRAM模组
| 型号： | HYS64T32900EDL-3.7-B2 |
| 厂家： | 
QIMONDA AG |
| 描述： | 200-Pin SO-DIMM DDR2 SDRAM Modules |
| 文件： | 总86页 (文件大小：4614K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
January 2007
HYS64T32x00EDL–[25F/…/3.7]–B2
HYS64T64x20EDL–[25F/…/3.7]–B2
HYS64T128x21EDL–[25F/…/3.7]B2
200-Pin SO-DIMM DDR2 SDRAM Modules
DDR2 SDRAM
RoHs Compliant Products
Internet Data Sheet
Rev. 1.1
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
HYS64T32x00EDL–[25F/…/3.7]–B2, HYS64T64x20EDL–[25F/…/3.7]–B2, HYS64T128x21EDL–[25F/…/3.7]B2
Revision History: 2007-01, Rev. 1.1
Page
Subjects (major changes since last revision)
All
All
4
Adapted internet edition
Updated HYS64T[32/64/128]9xxEDL–[25F/.../3.7](–)B2
Table 2 corrected product string to 21 digits
Previous Revision: 2006-10, Rev. 1.0
We Listen to Your Comments
Any information within this document that you feel is wrong, unclear or missing at all?
Your feedback will help us to continuously improve the quality of this document.
Please send your proposal (including a reference to this document) to:
techdoc@qimonda.com
qag_techdoc_rev400 / 3.2 QAG / 2006-08-07
08212006-PKYN-2H1B
2
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
1
Overview
This chapter gives an overview of the 200-Pin SO-DIMM DDR2 SDRAM Modules product family and describes its main
characteristics.
1.1
Features
•
200-Pin PC2–6400, PC2–5300 and PC2–4200 DDR2
SDRAM memory modules for use as main memory when
installed in systems such as mobile personal computers.
32M × 64, 64M × 64 and 128M × 64 module
organization,and 32M × 16, 64M × 8 chip organization
Standard Double-Data-Rate-Two Synchronous DRAMs
(DDR2 SDRAM) with a single + 1.8 V (± 0.1 V) power
supply
•
•
•
•
Programmable self refresh rate via EMRS2 setting
Programmable partial array refresh via EMRS2 settings
DCC enabling via EMRS2 setting
All speed grades faster than DDR2–400 comply with
DDR2–400 timing specifications.
•
•
•
•
All inputs and outputs SSTL_1.8 compatible
Off-Chip Driver Impedance Adjustment (OCD) and On-Die
Termination (ODT)
•
256MB, 512MB and 1GB modules built with 512-Mbit
DDR2 SDRAMs in PG-TFBGA-60 and PG-TFBGA-84
chipsize packages
•
•
Serial Presence Detect with E2PROM
SO-DIMM Dimensions (nominal): 30 mm high,
67.60 mm wide
•
•
Programmable CAS Latencies (3, 4 ,5 and 6), Burst
Length (8 & 4) and Burst Type
Auto Refresh (CBR) and Self Refresh
•
•
Based on standard reference layouts Raw Card “A”,
“C”,”E”
RoHS compliant products1)
TABLE 1
Performance Table
Product Type Speed Code
Speed Grade
–2.5F
–2.5
–3
–3S
–3.7
Unit
PC2–6400
5–5–5
PC2–6400
6–6–6
PC2–5300
4–4–4
PC2–5300
5–5–5
PC2–4200
4–4–4
—
Max. Clock Frequency
@CL6 fCK6 400
@CL5 fCK5 400
400
333
266
200
15
—
—
—
MHz
MHz
MHz
MHz
ns
333
333
200
12
333
266
200
15
266
266
200
15
@CL4 fCK4 266
@CL3 fCK3 200
tRCD 12.5
Min. RAS-CAS-Delay
Min. Row Precharge Time
Min. Row Active Time
Min. Row Cycle Time
tRP
12.5
15
12
15
15
ns
tRAS 45
45
45
45
45
ns
tRC 57.5
60
57
60
60
ns
1) RoHS Compliant Product: Restriction of the use of certain hazardous substances (RoHS) in electrical and electronic equipment as defined
in the directive 2002/95/EC issued by the European Parliament and of the Council of 27 January 2003. These substances include mercury,
lead, cadmium, hexavalent chromium, polybrominated biphenyls and polybrominated biphenyl ethers.
Rev. 1.1, 2007-01
3
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
1.2
Description
The Qimonda HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
module family are small outline DIMM modules “SO-DIMMs”
with 30 mm height based on DDR2 technology. DIMMs are
available as non-ECC modules in 32M × 64 (256 MB),
64M × 64 (512 MB) and 128M × 64 (1 GB) organization and
density, intended for mounting into 200-pin connector
sockets.
capacitors are mounted on the PCB board. The DIMMs
feature serial presence detect based on a serial E2PROM
device using the 2-pin I2C protocol. The first 128 bytes are
programmed with configuration data and are write protected;
the second 128 bytes are available to the customer.
The memory array is designed with 512-Mbit Double-Data-
Rate-Two (DDR2) Synchronous DRAMs. Decoupling
TABLE 2
Ordering Information for RoHS Compliant Products
Product Type1)
PC2–6400
Compliance Code2)
Description
SDRAM
Technology
HYS64T32000EDL–25F–B2
HYS64T32900EDL–25F–B2
256 MB 1R × 16 PC2–6400S–555–12–C0
512 MB 2R × 16 PC2–6400S–555–12–A0
1 GB 2R × 8 PC2-6400S–555–12–E0
1 Rank, Non-ECC
2 Rank, Non-ECC
2 Rank, Non-ECC
512 Mbit (×16)
512 Mbit (×16)
512 Mbit (×8)
HYS64T64020EDL–25F–B2
HYS64T64920EDL–25F–B2
HYS64T128021EDL–25FB2
HYS64T128921EDL–25FB2
PC2–6400
HYS64T32000EDL–2.5–B2
HYS64T32900EDL–2.5–B2
256 MB 1R × 16 PC2–6400S–666–12–C0
512 MB 2R × 16 PC2–6400S–666–12–A0
1 GB 2R × 8 PC2-6400S–666–12–E0
1 Rank, Non-ECC
2 Rank, Non-ECC
2 Rank, Non-ECC
512 Mbit (×16)
512 Mbit (×16)
512 Mbit (×8)
HYS64T64020EDL–2.5–B2
HYS64T64920EDL–2.5–B2
HYS64T128021EDL–2.5B2
HYS64T128921EDL–2.5B2
PC2–5300
HYS64T32000EDL–3–B2
HYS64T32900EDL–3–B2
256 MB 1R × 16 PC2–5300S–444–12–C0
512 MB 2R × 16 PC2–5300S–444–12–A0
1 GB 2R × 8 PC2-5300S–444–12–E0
1 Rank, Non-ECC
2 Rank, Non-ECC
2 Rank, Non-ECC
512 Mbit (×16)
512 Mbit (×16)
512 Mbit (×8)
HYS64T64020EDL–3–B2
HYS64T64920EDL–3–B2
HYS64T128021EDL–3–B2
HYS64T128921EDL–3–B2
PC2–5300
HYS64T32000EDL–3S–B2
HYS64T32900EDL–3S–B2
256 MB 1R × 16 PC2–5300S–555–12–C0
512 MB 2R × 16 PC2–5300S–555–12–A0
1 GB 2R × 8 PC2-5300S–555–12–E0
1 Rank, Non-ECC
2 Rank, Non-ECC
2 Rank, Non-ECC
512 Mbit (×16)
512 Mbit (×16)
512 Mbit (×8)
HYS64T64020EDL–3S–B2
HYS64T64920EDL–3S–B2
HYS64T128021EDL–3S–B2
HYS64T128921EDL–3S–B2
Rev. 1.1, 2007-01
4
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type1)
PC2–4200
Compliance Code2)
Description
SDRAM
Technology
HYS64T32000EDL–3.7–B2
HYS64T32900EDL–3.7–B2
256 MB 1R × 16 PC2–4200S–444–12–C0
512 MB 2R × 16 PC2–4200S–444–12–A0
1 GB 2R × 8 PC2-4200S–444–12–E0
1 Rank, Non-ECC
2 Rank, Non-ECC
2 Rank, Non-ECC
512 Mbit (×16)
512 Mbit (×16)
512 Mbit (×8)
HYS64T64020EDL–3.7–B2
HYS64T64920EDL–3.7–B2
HYS64T128021EDL–3.7B2
HYS64T128921EDL–3.7B2
1) All Product Type numbers end with a place code, designating the silicon die revision. Example: HYS64T64020EDL–3.7–B2, indicating
Rev. “B” dies are used for DDR2 SDRAM components. For all Qimonda DDR2 module and component nomenclature see Chapter 6 of
this data sheet.
2) The Compliance Code is printed on the module label and describes the speed grade, for example “PC2–4200S–444–12–A0”, where
4200S means Small Outlined Unbuffered DIMM modules with 4.26 GB/sec Module Bandwidth and “444-12” means Column Address
Strobe (CAS) latency = 4, Row Column Delay (RCD) latency = 4 and Row Precharge (RP) latency = 4 using the latest JEDEC SPD
Revision 1.2 and produced on the Raw Card “A”.
TABLE 3
Address Format
DIMM
Density
Module
Organization
Memory
Ranks
ECC/
Non-ECC
# of SDRAMs # of row/bank/column
bits
Raw
Card
256 MByte
512 MByte
1 GByte
32M × 64
64M × 64
128M × 64
1
2
2
Non-ECC
Non-ECC
Non-ECC
4
13/2/10
13/2/10
14/2/10
C
A
E
8
16
TABLE 4
Components on Modules
DRAM Organisation
32M × 16
Product Type1)2)
DRAM Components2)
DRAM Density
HYS64T32000EDL
HYS64T32900EDL
HYB18T512160B2F
512 Mbit
HYS64T64020EDL
HYS64T64920EDL
HYB18T512160B2F
HYB18T512800B2F
512 Mbit
512 Mbit
32M × 16
64M × 8
HYS64T128021EDL
HYS64T128921EDL
1) For a detailed description of all functionalities of the DRAM components on these modules see the component data sheet.
2) Green Product
Rev. 1.1, 2007-01
5
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
2
Pin Configurations
2.1
Chip Configuration
The chip configuration of the Small Outline DDR2 SDRAM DIMM is listed by function in Table 2 (200 balls). The abbreviations
used in columns Ball and Buffer Type are explained in Table 3 and Table 4 respectively. The Ball numbering is depicted in
Figure 1.
TABLE 5
Chip Configuration of SO-DIMM
Ball No.
Name
Pin
Buffer
Function
Type Type
Clock Signals
30
CK0
CK1
CK0
CK1
CKE0
CKE1
NC
I
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
—
Clock Signals 2:0, Complement Clock Signals 2:0
164
32
I
I
166
79
I
I
Clock Enable Rank 1:0
Note: 2 Ranks module
80
I
NC
Not Connected
Note: 1-rank module
Control Signals
110
115
S0
S1
NC
I
SSTL
SSTL
—
Chip Select Rank 1:0
I
NC
Not Connected
Note: 1-rank module
Row Address Strobe
Column Address Strobe
Write Enable
108
RAS
CAS
WE
I
I
I
SSTL
SSTL
SSTL
113
109
Address Signals
107
106
85
BA0
BA1
BA2
I
I
I
SSTL
SSTL
SSTL
Bank Address Bus 2:0
Bank Address Bus 2
Greater than 512Mb DDR2 SDRAMS
NC
NC
SSTL
Less than 1Gb DDR2 SDRAMS
Rev. 1.1, 2007-01
6
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Ball No.
Name
Pin
Buffer
Function
Type Type
102
101
100
99
A0
I
I
I
I
I
I
I
I
I
I
I
I
I
I
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
Address Bus 12:0
A1
A2
A3
98
A4
97
A5
94
A6
92
A7
93
A8
91
A9
105
A10
AP
A11
A12
90
89
Address Signal 12
Note: Module based on 256 Mbit or larger dies
Address Signal 13
116
A13
NC
I
SSTL
—
Note: 1 Gbit based module
Not Connected
NC
Note: Module based on 512 Mbit or smaller dies
Data Signals
5
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
Data Bus 63:0
Note: Data Input/Output Balls
7
17
19
4
6
14
16
23
25
35
37
Rev. 1.1, 2007-01
7
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Ball No.
Name
Pin
Buffer
Function
Type Type
20
DQ12
DQ13
DQ14
DQ15
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
DQ32
DQ33
DQ34
DQ35
DQ36
DQ37
DQ38
DQ39
DQ40
DQ41
DQ42
DQ43
DQ44
DQ45
DQ46
DQ47
DQ48
DQ49
DQ50
DQ51
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
Data Bus 63:0
Data Input/Output Balls
22
36
38
43
45
55
57
44
46
56
58
61
63
73
75
62
64
74
76
123
125
135
137
124
126
134
136
141
143
151
153
140
142
152
154
157
159
173
175
Rev. 1.1, 2007-01
8
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Ball No.
Name
Pin
Buffer
Function
Type Type
158
DQ52
DQ53
DQ54
DQ55
DQ56
DQ57
DQ58
DQ59
DQ60
DQ61
DQ62
DQ63
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
Data Bus 63:0
160
174
176
179
181
189
191
180
182
192
194
Data Strobe Signals
13
DQS0
DQS0
DQS1
DQS1
DQS2
DQS2
DQS3
DQS3
DQS4
DQS4
DQS5
DQS5
DQS6
DQS6
DQS7
DQS7
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
Data Strobe Bus 7:0
11
31
29
51
49
70
68
131
129
148
146
169
167
188
186
Data Mask Signals
10
DM0
DM1
DM2
DM3
DM4
DM5
DM6
DM7
I
I
I
I
I
I
I
I
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
SSTL
Data Mask Bus 7:0
26
52
67
130
147
170
185
EEPROM
197
SCL
I
CMOS Serial Bus Clock
Rev. 1.1, 2007-01
9
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Ball No.
Name
Pin
Buffer
Function
Type Type
195
SDA
SA0
SA1
I/O
OD
Serial Bus Data
198
I
I
CMOS Serial Address Select Bus 2:0
200
CMOS
Power Supplies
1
VREF
AI
—
—
—
I/O Reference Voltage
EEPROM Power Supply
Power Supply
199
VDDSPD PWR
81,82,87,88,95,96,103,104,
111,112,117,118
VDD
PWR
2,3,8,9,12,15,18,21,24,27,28,
33,34,39,40,41,42,47,48,53,
54,59,60,65,66,71,72,77,78,
121,122,127,128,132,133,138,13
9,144,145,149,150,155,156,
161,162,165,171,172,177,
VSS
GND
—
Ground Plane
178,183,184,187,190,193,196
Other Balls
114
ODT0
ODT1
I
I
SSTL
SSTL
On-Die Termination Control 1:0
On-Die Termination Control 1
Note: 2 Rank modules
Not Connected
119
NC
NC
NC
NC
—
—
Note: 1 Rank modules
Not connected
50,69,83,84,120,163,168
Rev. 1.1, 2007-01
10
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
TABLE 6
Abbreviations for Ball Type
Abbreviation
Description
I
Standard input-only Ball. Digital levels.
Output. Digital levels.
I/O is a bidirectional input/output signal.
Input. Analog levels.
Power
O
I/O
AI
PWR
GND
NC
Ground
Not Connected
TABLE 7
Abbreviations for Buffer Type
Abbreviation
Description
SSTL
Serial Stub Terminated Logic (SSTL_18)
Low Voltage CMOS
LV-CMOS
CMOS
OD
CMOS Levels
Open Drain. The corresponding ball has 2 operational states, active low and tristate, and
allows multiple devices to share as a wire-OR.
Rev. 1.1, 2007-01
11
08212006-PKYN-2H1B
9ꢀ5()ꢀꢈꢀ 3LQꢀꢁ
'4ꢁꢀꢈꢀ 3LQꢀꢁ
9ꢀ66ꢀꢈꢀ 3LQꢀꢁ
'46ꢁꢀꢈꢀ 3LQꢀꢁ
'4ꢄꢀꢈꢀ 3LQꢀꢁ
9ꢀ66ꢀꢈꢀ 3LQꢀꢁ
'4ꢋꢀꢈꢀ 3LQꢀꢁ
'46ꢂꢀꢈꢀ 3LQꢀꢁ
9ꢀ66ꢀꢈꢀ 3LQꢀꢁ
ꢁꢂꢀ
ꢁꢉꢀ
ꢁꢋꢀ
ꢂꢇꢀ
ꢂꢊꢀ
ꢄꢂꢀ
ꢄꢉꢀ
ꢄꢋꢀ
ꢇꢇꢀ
ꢇꢊꢀ
3LQꢀꢁꢁ
3LQꢀꢁꢁ
3LQꢀꢁꢂ
3LQꢀꢁꢂ
3LQꢀꢁꢂ
3LQꢀꢁꢄ
3LQꢀꢁꢄ
3LQꢀꢁꢇ
3LQꢀꢁꢇ
3LQꢀꢁꢇ
ꢄꢀꢈꢀ
ꢅꢀꢈꢀ
ꢁꢀꢈꢀ
ꢃꢀꢈꢀ
ꢆꢀꢈꢀ
ꢄꢀꢈꢀ
ꢅꢀꢈꢀ
ꢁꢀꢈꢀ
ꢃꢀꢈꢀ
ꢆꢀꢈꢀ
ꢁꢇ
ꢁꢊ
ꢂꢂ
ꢂꢉ
ꢂꢋ
ꢄꢇ
ꢄꢊ
ꢇꢂ
ꢇꢉ
ꢇꢋ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
3
3
3
3
3
3
3
3
3
3
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
ꢀꢁꢁꢃꢀ ꢈꢀ
'4ꢃꢀ
'4
'0
'4
9ꢀ
ꢉꢀ
ꢁꢀ
ꢅꢀ
'4ꢂꢀꢈꢀ 3LQꢀꢁ
'46ꢁꢀꢈꢀ 3LQꢀꢁ
9ꢀ66ꢀꢈꢀ 3LQꢀꢁ
'4ꢇꢀꢈꢀ 3LQꢀꢁ
'4ꢆꢀꢈꢀ 3LQꢀꢁ
9ꢀ66ꢀꢈꢀ 3LQꢀꢁ
ꢀꢁꢁꢆꢀ ꢈꢀ9ꢀ
ꢀꢁꢂꢄꢀ ꢈꢀ9ꢀ
66ꢀ
ꢀꢁꢂꢅꢀ ꢈꢀ'4ꢊꢀ
ꢀꢁꢄꢁꢀ ꢈꢀ'4ꢂꢄꢀ
'4
'0
&.ꢁꢀ
ꢂꢇ
ꢂꢀ
ꢀ
ꢀꢁꢄꢃꢀ ꢈꢀ9ꢀ
ꢀꢁꢄꢆꢀ ꢈꢀ9ꢀ
'46ꢂꢀꢈꢀ 3LQꢀꢁ
ꢀꢁꢇꢄꢀ ꢈꢀ&.ꢁꢀ
'4
ꢀꢁꢇꢅꢀ ꢈꢀ'4ꢂ
ꢂꢁꢀꢈꢀ 3LQꢀꢁ
ꢃꢀ
'4ꢂꢂꢀꢈꢀ 3LQꢀꢁ
'4
ꢂꢉ
ꢀ
ꢀ
9ꢀ66ꢀꢈꢀ 3LQꢀꢁ
ꢀꢁꢃꢁꢀ ꢈꢀ9ꢀ
9ꢀ66ꢀꢈꢀ 3LQꢀꢁ
'4 ꢊꢀꢈꢀ 3LQꢀꢁ
'46ꢄꢀꢈꢀ 3LQꢀꢁ
9ꢀ66ꢀꢈꢀ 3LQꢀꢁ
ꢃꢂꢀ
ꢃꢉꢀ
ꢃꢋꢀ
ꢉꢇꢀ
ꢉꢊꢀ
ꢅꢂꢀ
ꢅꢉꢀ
ꢅꢋꢀ
ꢊꢇꢀ
ꢊꢊꢀ
ꢆꢂꢀ
ꢆꢉꢀ
ꢆꢋꢀ
ꢋꢇꢀ
ꢋꢊꢀ
ꢁꢂꢀ
ꢁꢉꢀ
ꢁꢋꢀ
ꢂꢇꢀ
ꢂꢊꢀ
ꢄꢂꢀ
ꢄꢉꢀ
ꢄꢋꢀ
ꢇꢇꢀ
ꢇꢊꢀ
ꢃꢂꢀ
ꢃꢉꢀ
ꢃꢋꢀ
ꢉꢇꢀ
ꢉꢊꢀ
ꢅꢂꢀ
ꢅꢉꢀ
ꢅꢋꢀ
ꢊꢇꢀ
ꢊꢊꢀ
ꢆꢂꢀ
ꢆꢉꢀ
ꢆꢋꢀ
ꢋꢇꢀ
ꢋꢊꢀ
3LQꢀꢁꢃ
3LQꢀꢁꢃ
3LQꢀꢁꢉ
3LQꢀꢁꢉ
3LQꢀꢁꢉ
3LQꢀꢁꢅ
3LQꢀꢁꢅ
3LQꢀꢁꢊ
3LQꢀꢁꢊ
3LQꢀꢁꢊ
3LQꢀꢁꢆ
3LQꢀꢁꢆ
3LQꢀꢁꢋ
3LQꢀꢁꢋ
3LQꢀꢁꢋ
3LQꢀꢂꢁ
3LQꢀꢂꢁ
3LQꢀꢂꢂ
3LQꢀꢂꢂ
3LQꢀꢂꢂ
3LQꢀꢂꢄ
3LQꢀꢂꢄ
3LQꢀꢂꢇ
3LQꢀꢂꢇ
3LQꢀꢂꢇ
3LQꢀꢂꢃ
3LQꢀꢂꢃ
3LQꢀꢂꢉ
3LQꢀꢂꢉ
3LQꢀꢂꢉ
3LQꢀꢂꢅ
3LQꢀꢂꢅ
3LQꢀꢂꢊ
3LQꢀꢂꢊ
3LQꢀꢂꢊ
3LQꢀꢂꢆ
3LQꢀꢂꢆ
3LQꢀꢂꢋ
3LQꢀꢂꢋ
3LQꢀꢂꢋ
ꢄꢀꢈꢀ 9ꢀ
66ꢀ
'4ꢂ
9ꢀ66ꢀꢈꢀ3LQꢀꢁ
ꢅꢀꢈꢀ3LQꢀꢁ
ꢃꢇꢀ
ꢃꢊꢀ
ꢉꢂꢀ
ꢉꢉꢀ
ꢉꢋꢀ
ꢅꢇꢀ
ꢅꢊꢀ
ꢊꢂꢀ
ꢊꢉꢀ
ꢊꢋꢀ
ꢆꢇꢀ
ꢆꢊꢀ
ꢋꢂꢀ
ꢋꢉꢀ
ꢋꢋꢀ
ꢁꢇꢀ
ꢁꢊꢀ
ꢂꢂꢀ
ꢂꢉꢀ
ꢂꢋꢀ
ꢄꢇꢀ
ꢄꢊꢀ
ꢇꢂꢀ
ꢇꢉꢀ
ꢇꢋꢀ
ꢃꢇꢀ
ꢃꢊꢀ
ꢉꢂꢀ
ꢉꢉꢀ
ꢉꢋꢀ
ꢅꢇꢀ
ꢅꢊꢀ
ꢊꢂꢀ
ꢊꢉꢀ
ꢊꢋꢀ
ꢆꢇꢀ
ꢆꢊꢀ
ꢋꢂꢀ
ꢋꢉꢀ
ꢋꢋꢀ
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
LQ
ꢀꢁꢃꢃꢀꢈꢀ '4ꢄ
ꢁꢀ
%ꢀ
$ꢀ
&ꢀ
.ꢀ
6ꢀ
,ꢀ
ꢅꢀꢈꢀ '4
ꢄꢂ
ꢂ
ꢀꢁꢃꢆꢀꢈꢀ 9ꢀ
ꢁꢀꢈꢀ 1&ꢌ
(
9(17ꢀ
'46
ꢄꢀꢈꢀ3LQꢀꢁ
ꢆꢀꢈꢀ3LQꢀꢁ
ꢀꢁꢉꢄꢀꢈꢀ '0
ꢄꢀ
ꢃꢀꢈꢀ 9ꢀ
'4ꢂ
ꢀꢁꢉꢅꢀꢈꢀ '4ꢄ
ꢄꢀ
'4
'4
ꢋꢀꢈꢀ 3LQꢀꢁ
ꢃꢀꢈꢀ 3LQꢀꢁ
ꢆꢀꢈꢀ '4
ꢄꢀꢈꢀ '4
ꢅꢀꢈꢀ 9ꢀ
ꢄꢇ
ꢄꢆ
ꢂ
ꢄ
ꢀ
ꢀ
9ꢀ66ꢀꢈꢀ3LQꢀꢁ
'4ꢄꢉꢀꢈꢀ3LQꢀꢁ
'0ꢇ
ꢀꢁꢅꢁꢀꢈꢀ 9ꢀ
ꢀꢁꢅꢃꢀꢈꢀ '4ꢄ
ꢀꢁꢅꢆꢀꢈꢀ '46ꢇꢀ
ꢋꢀ
9ꢀ66ꢀꢈꢀ 3LQꢀꢁ
1&ꢀꢈꢀ 3LQꢀꢁ
ꢀꢈꢀ3LQꢀꢁ
ꢁꢀꢈꢀ '4
ꢃꢀꢈꢀ '4
ꢆꢀꢈꢀ 9ꢀ
6ꢇꢀ
ꢀ
9ꢀ66ꢀꢈꢀ3LQꢀꢁ
ꢀꢁꢊꢄꢀꢈꢀ 9ꢀ
'4
ꢅꢀꢈꢀ 3LQꢀꢁ
ꢇꢁ
ꢄ
'4ꢄ
ꢊꢀꢈꢀ3LQꢀꢁ
&.(ꢁꢀꢈꢀ3LQꢀꢁ
1&ꢀꢈꢀ3LQꢀꢁ
9ꢀ''ꢀꢈꢀ3LQꢀꢁ
$ꢋꢀꢈꢀ3LQꢀꢁ
ꢀꢁꢊꢅꢀꢈꢀ '4ꢇꢂꢀ
ꢀꢁꢆꢁꢀꢈꢀ 1&ꢌ&.(ꢂꢀ
ꢀꢁꢆꢃꢀꢈꢀ 1&ꢀ
9ꢀ66ꢀꢈꢀ 3LQꢀꢁ
9ꢀ''ꢀꢈꢀ 3LQꢀꢁ
ꢄꢀꢈꢀ 9ꢀ
''ꢀ
1&ꢌ
%
$ꢂ
$
ꢄꢀꢈꢀ 3LQꢀꢁ
ꢄꢀꢈꢀ 3LQꢀꢁ
ꢅꢀꢈꢀ 1&ꢌ
ꢁꢀꢈꢀ $ꢂꢂ
ꢃꢀꢈꢀ $ꢅꢀ
ꢆꢀꢈꢀ $ꢃꢀ
ꢄꢀꢈꢀ $ꢁꢀ
$
ꢀ
ꢂ
ꢃꢀ
ꢀꢁꢆꢆꢀꢈꢀ 9ꢀ
ꢀꢁꢋꢄꢀꢈꢀ $ꢊꢀ
$ꢆꢀꢈꢀ 3LQꢀꢁ
$ꢉꢀꢈꢀ 3LQꢀꢁ
$ꢂꢀꢈꢀ 3LQꢀꢂ
$3ꢀꢈꢀ 3LQꢀꢂ
9ꢀ''ꢀꢈꢀ3LQꢀꢁ
$ꢇꢀꢈꢀ3LQꢀꢁ
9ꢀ''ꢀꢈꢀ3LQꢀꢂ
%$ꢁꢀꢈꢀ3LQꢀꢂ
9ꢀ''ꢀꢈꢀ3LQꢀꢂ
ꢀꢁꢋꢅꢀꢈꢀ 9ꢀ
ꢀꢂꢁꢁꢀꢈꢀ $ꢄꢀ
ꢀꢂꢁꢃꢀꢈꢀ 9ꢀ
$ꢂꢁ
ꢌ
ꢅꢀꢈꢀ %$ꢂꢀ
ꢁꢀꢈꢀ 6ꢁꢀ
ꢀꢂꢁꢆꢀꢈꢀ 5$6ꢀ
:(ꢀꢈꢀ 3LQꢀꢂ
ꢀꢂꢂꢄꢀꢈꢀ 9ꢀ
&$6ꢀꢈꢀ 3LQꢀꢂ
9ꢀ''ꢀꢈꢀ 3LQꢀꢂ
9ꢀ66ꢀꢈꢀ 3LQꢀꢂ
ꢃꢀꢈꢀ 2'
ꢆꢀꢈꢀ 9ꢀ
7ꢁꢀ
1&ꢌ
1&ꢌ2
'4ꢇ
6ꢂꢀꢈꢀ3LQꢀꢂ
ꢀꢂꢂꢅꢀꢈꢀ 1&ꢌ$ꢂ
ꢀꢂꢄꢁꢀꢈꢀ 1&ꢀ
ꢀꢂꢄꢃꢀꢈꢀ '4ꢇ
ꢇꢀ
'
ꢂꢀꢈꢀ3LQꢀꢂ
ꢄꢀꢈꢀ3LQꢀꢂ
7
ꢄꢀꢈꢀ 9ꢀ
ꢅꢀ
'4
ꢇꢀꢈꢀ 3LQꢀꢂ
ꢅꢀꢈꢀ '4
ꢁꢀꢈꢀ '0
ꢃꢀꢈꢀ '4
ꢆꢀꢈꢀ 9ꢀ
ꢇꢊ
ꢃꢀ
ꢇꢆ
ꢇ
ꢀ
ꢀ
ꢀ
9ꢀ66ꢀꢈꢀ3LQꢀꢂ
ꢀꢂꢄꢆꢀꢈꢀ 9ꢀ
'46ꢃꢀꢈꢀ 3LQꢀꢂ
9ꢀ66ꢀꢈꢀ 3LQꢀꢂ
'46
ꢃꢀꢈꢀ3LQꢀꢂ
ꢃꢀꢈꢀ3LQꢀꢂ
ꢀꢂꢇꢄꢀꢈꢀ 9ꢀ
'4ꢇ
ꢀꢂꢇꢅꢀꢈꢀ '4ꢇ
ꢀꢂꢃꢁꢀꢈꢀ '4ꢃ
ꢋꢀ
ꢃꢀ
'4
'4
ꢉꢀꢈꢀ 3LQꢀꢂ
ꢁꢀꢈꢀ 3LQꢀꢂ
ꢇ
ꢃ
9ꢀ66ꢀꢈꢀ3LQꢀꢂ
'4ꢃꢂꢀꢈꢀ3LQꢀꢂ
'0ꢉ
'4ꢃ
9ꢀ66ꢀꢈꢀ3LQꢀꢂ
ꢄꢀꢈꢀ '4
ꢅꢀꢈꢀ '4
ꢁꢀꢈꢀ 9ꢀ
ꢃꢉ
ꢀꢂꢃꢃꢀꢈꢀ 9ꢀ
9ꢀ66ꢀꢈꢀ 3LQꢀꢂ
9ꢀ66ꢀꢈꢀ 3LQꢀꢂ
6ꢉꢀ
ꢀꢈꢀ3LQꢀꢂ
ꢄꢀꢈꢀ3LQꢀꢂ
ꢀꢂꢃꢆꢀꢈꢀ '46ꢉꢀ
ꢀꢂꢉꢄꢀꢈꢀ '4ꢃ
ꢅꢀ
'4
'4
ꢇꢀꢈꢀ 3LQꢀꢂ
ꢆꢀꢈꢀ 3LQꢀꢂ
ꢃꢀꢈꢀ '4
ꢆꢀꢈꢀ '4
ꢄꢀꢈꢀ 9ꢀ
ꢃꢊ
ꢉꢄ
ꢃ
ꢃ
ꢀ
ꢀ
ꢀꢂꢉꢅꢀꢈꢀ 9ꢀ
'4ꢃ
1&ꢀꢈꢀ3LQꢀꢂ
ꢋꢀꢈꢀ3LQꢀꢂ
ꢀꢂꢅꢁꢀꢈꢀ '4ꢉ
ꢀꢂꢅꢃꢀꢈꢀ &.ꢂꢀ
ꢇꢀ
9ꢀ66ꢀꢈꢀ 3LQꢀꢂ
9ꢀ66ꢀꢈꢀ 3LQꢀꢂ
ꢅꢀꢈꢀ &.ꢂꢀ
'4
ꢅꢀꢈꢀ3LQꢀꢂ
6
ꢀꢂꢅꢆꢀꢈꢀ 9ꢀ
3LQꢀꢂ
ꢁꢀ
ꢈꢀ '0
'46ꢅꢀꢈꢀ
'4 ꢁꢀꢈꢀ 3LQꢀꢂ
9ꢀ66ꢀꢈꢀ 3LQꢀꢂ
'4 ꢊꢀꢈꢀ 3LQꢀꢂ
'0ꢊꢀꢈꢀ 3LQꢀꢂ
3LQꢀꢂ
ꢅꢀ
9ꢀ66ꢀꢈꢀ3LQꢀꢂ
'4ꢉ
'4ꢉ
9ꢀ66ꢀꢈꢀ3LQꢀꢂ
9ꢀ66ꢀꢈꢀ3LQꢀꢂ
'4ꢉ
ꢀꢂꢊꢄꢀꢈꢀ 9ꢀ
ꢃꢀꢈꢀ '4
ꢆꢀꢈꢀ 9ꢀ
ꢉꢃ
ꢉ
ꢀ
ꢀ
ꢂꢀꢈꢀ3LQꢀꢂ
ꢅꢀꢈꢀ3LQꢀꢂ
ꢀꢂꢊꢅꢀꢈꢀ '4ꢉ
ꢀꢂꢆꢁꢀꢈꢀ '4ꢅ
ꢉꢀ
ꢁꢀ
ꢄꢀꢈꢀ '4
ꢅꢀꢈꢀ '4
ꢅꢂ
ꢉ
ꢀꢂꢆꢃꢀꢈꢀ 9ꢀ
6ꢊꢀ
ꢀꢂꢆꢆꢀꢈꢀ '46ꢊꢀ
ꢀꢂꢋꢄꢀꢈꢀ '4ꢅꢄꢀ
ꢁꢀ
ꢈꢀ 9ꢀ
'4 ꢆꢀꢈꢀ
ꢉ
ꢋꢀꢈꢀ3LQꢀꢂ
9ꢀ66ꢀꢈꢀ 3LQꢀꢂ
3LQꢀꢂ
ꢃꢀꢈꢀ '4
ꢅꢇ
ꢈꢀ 6$ꢁꢀ
ꢀ
6'$ꢀꢈꢀ3LQꢀꢂ
9ꢀ 63'ꢀꢈꢀ3LQꢀꢂ
''ꢀ
ꢀꢂꢋꢅꢀꢈꢀ 9ꢀ
ꢆꢀ
ꢀꢄꢁꢁꢀꢈꢀ 6$ꢂꢀ
0
33
7
ꢁꢂꢃꢁꢀ
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
FIGURE 1
Chip Configuration SO-DIMM (200 Ball)
9ꢀ
66ꢀ
9ꢀ
66ꢀ ꢈꢀ 3LQꢀꢁ
66ꢀ
66ꢀ
66ꢀ
66ꢀ
9ꢀ
66ꢀ
66ꢀ
)ꢀ
5ꢀ
2ꢀ
1ꢀ
7ꢀ
6ꢀ
,ꢀ
66ꢀ
66ꢀ
66ꢀ
66ꢀ
'ꢀ
(ꢀ
'ꢀ
(ꢀ
66ꢀ
66ꢀ
''ꢀ
''ꢀ
''ꢀ
''ꢀ
''ꢀ
66ꢀ
66ꢀ
66ꢀ
66ꢀ
66ꢀ
66ꢀ
66ꢀ
66ꢀ
66ꢀ
66ꢀ
66ꢀ
66ꢀ
66ꢀ
66ꢀ
6&/ꢀꢈꢀ
Rev. 1.1, 2007-01
12
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
3
Electrical Characteristics
3.1
Absolute Maximum Ratings
Caution is needed not to exceed absolute maximum ratings of the DRAM device listed in Table 2 at any time.
TABLE 8
Absolute Maximum Ratings
Symbol
Parameter
Rating
Min.
Unit
Note
Max.
1)
VDD
Voltage on VDD pin relative to VSS
Voltage on VDDQ pin relative to VSS
Voltage on VDDL pin relative to VSS
Voltage on any pin relative to VSS
Storage Temperature
–1.0
–0.5
–0.5
–0.5
–55
+2.3
+2.3
+2.3
+2.3
+100
V
1)2)
1)2)
1)
VDDQ
VDDL
V
V
VIN, VOUT
TSTG
V
1)2)
°C
1) When VDD and VDDQ and VDDL are less than 500 mV; VREF may be equal to or less than 300 mV.
2) Storage Temperature is the case surface temperature on the center/top side of the DRAM.
Attention: Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to
the device. This is a stress rating only and functional operation of the device at these or any other
conditions above those indicated in the operational sections of this specification is not implied. Exposure
to absolute maximum rating conditions for extended periods may affect reliability.
TABLE 9
DRAM Component Operating Temperature Range
Symbol
Parameter
Rating
Unit
Note
Min.
Max.
1)2)3)4)
TOPER
Operating Temperature
0
95
°C
1) Operating Temperature is the case surface temperature on the center / top side of the DRAM.
2) The operating temperature range are the temperatures where all DRAM specification will be supported. During operation, the DRAM case
temperature must be maintained between 0 - 95 °C under all other specification parameters.
3) Above 85 °C the Auto-Refresh command interval has to be reduced to tREFI= 3.9 µs
4) When operating this product in the 85 °C to 95 °C TCASE temperature range, the High Temperature Self Refresh has to be enabled by
setting EMR(2) bit A7 to “1”. When the High Temperature Self Refresh is enabled there is an increase of IDD6 by approximately 50 %
Rev. 1.1, 2007-01
13
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
3.2
DC Operating Conditions
TABLE 10
Supply Voltage Levels and DC Operating Conditions
Parameter
Symbol
Values
Min.
Unit
Note
Typ.
Max.
Device Supply Voltage
Output Supply Voltage
Input Reference Voltage
SPD Supply Voltage
VDD
1.7
1.8
1.9
V
—
1)
VDDQ
VREF
1.7
1.8
1.9
V
2)
0.49 × VDDQ
0.5 × VDDQ
0.51 × VDDQ
V
VDDSPD
VIH(DC)
VIL (DC
IL
1.7
—
—
—
—
3.6
V
—
—
DC Input Logic High
V
REF + 0.125
V
V
5
DDQ + 0.3
V
DC Input Logic Low
)
– 0.30
– 5
REF – 0.125
V
—
3)
In / Output Leakage Current
µA
1) Under all conditions, VDDQ must be less than or equal to VDD
2) Peak to peak AC noise on VREF may not exceed ± 2 % VREF (DC).VREF is also expected to track noise in VDDQ
3) Input voltage for any connector pin under test of 0 V ≤ VIN ≤ VDDQ + 0.3 V; all other pins at 0 V. Current is per pin
.
TABLE 11
Operating Conditions
Parameter
Symbol
Values
Min.
Unit
Note
Max.
Operating temperature (ambient)
DRAM Case Temperature
TOPR
TCASE
TSTG
0
+65
+95
+100
+105
90
°C
°C
°C
kPa
%
—
1)2)3)4)
0
Storage Temperature
– 50
+69
10
—
5)
Barometric Pressure (operating & storage)
Operating Humidity (relative)
PBar
HOPR
—
1) DRAM Component Case Temperature is the surface temperature in the center on the top side of any of the DRAMs.
2) Within the DRAM Component Case Temperature Range all DRAM specifications will be supported
3) Above 85 °C DRAM Case Temperature the Auto-Refresh command interval has to be reduced to tREFI = 3.9 µs
4) When operating this product in the 85 °C to 95 °C TCASE temperature range, the High Temperature Self Refresh has to be enabled by
setting EMR(2) bit A7 to “1”. When the High Temperature Self Refresh is enabled there is an increase of IDD6 by approximately 50 %.
5) Up to 3000 m.
Rev. 1.1, 2007-01
14
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
3.3
Timing Characteristics
All Speed grades faster than DDR2-DDR400B comply with DDR2-DDR400B timing specifications(tCK = 5ns with tRAS = 40ns).
3.3.1
Speed Grade Definitions
Speed Grade Definition: Table 12 for DDR2–800; Table 13 for DDR2–667 and Table 14 for DDR2–533C.
TABLE 12
Speed Grade Definition Speed Bins for DDR2–800
Speed Grade
DDR2–800D
DDR2–800E
Unit
Note
QAG Sort Name
CAS-RCD-RP latencies
–2.5F
–2.5
5–5–5
6–6–6
tCK
Parameter
Symbol
Min.
Max.
Min.
Max.
—
1)2)3)4)
1)2)3)4)
1)2)3)4)
1)2)3)4)
1)2)3)4)5)
1)2)3)4)
1)2)3)4)
1)2)3)4)
Clock Frequency
@ CL = 3
@ CL = 4
@ CL = 5
@ CL = 6
tCK
5
8
5
8
ns
ns
ns
ns
ns
ns
ns
ns
tCK
3.75
2.5
8
3.75
3
8
tCK
8
8
tCK
2.5
45
8
2.5
45
60
15
15
8
Row Active Time
Row Cycle Time
RAS-CAS-Delay
Row Precharge Time
tRAS
tRC
tRCD
tRP
70000
—
70000
—
57.5
12.5
12.5
—
—
—
—
1) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew
Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode.
2) The CK/CK input reference level (for timing reference to CK/CK) is the point at which CK and CK cross. The DQS / DQS, RDQS / RDQS,
input reference level is the crosspoint when in differential strobe mode.
3) Inputs are not recognized as valid until VREF stabilizes. During the period before VREF stabilizes, CKE = 0.2 x VDDQ is recognized as low.
4) The output timing reference voltage level is VTT
.
5) RAS.MAX is calculated from the maximum amount of time a DDR2 device can operate without a refresh command which is equal to 9 x tREFI
t
.
Rev. 1.1, 2007-01
15
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
TABLE 13
Speed Grade Definition Speed Bins for DDR2–667
Speed Grade
DDR2–667C
DDR2–667D
Unit
Note
QAG Sort Name
CAS-RCD-RP latencies
–3
–3S
4–4–4
5–5–5
tCK
Parameter
Symbol
Min.
Max.
Min.
Max.
—
1)2)3)4)
1)2)3)4)
1)2)3)4)
1)2)3)4)5)
1)2)3)4)
1)2)3)4)
1)2)3)4)
Clock Frequency
@ CL = 3
@ CL = 4
@ CL = 5
tCK
5
8
5
8
ns
ns
ns
ns
ns
ns
ns
tCK
3
8
3.75
3
8
tCK
3
8
8
Row Active Time
Row Cycle Time
RAS-CAS-Delay
Row Precharge Time
tRAS
tRC
tRCD
tRP
45
57
12
12
70000
—
45
60
15
15
70000
—
—
—
—
—
1) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew
Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode.
2) The CK/CK input reference level (for timing reference to CK/CK) is the point at which CK and CK cross. The DQS / DQS, RDQS / RDQS,
input reference level is the crosspoint when in differential strobe mode.
3) Inputs are not recognized as valid until VREF stabilizes. During the period before VREF stabilizes, CKE = 0.2 x VDDQ is recognized as low.
4) The output timing reference voltage level is VTT
.
5) RAS.MAX is calculated from the maximum amount of time a DDR2 device can operate without a refresh command which is equal to 9 x tREFI
t
.
TABLE 14
Speed Grade Definition Speed Bins for DDR2–533C
Speed Grade
DDR2–533C
Unit
Note
QAG Sort Name
CAS-RCD-RP latencies
–3.7
4–4–4
tCK
Parameter
Symbol
Min.
Max.
—
1)2)3)4)
1)2)3)4)
1)2)3)4)
1)2)3)4)5)
1)2)3)4)
1)2)3)4)
1)2)3)4)
Clock Frequency
@ CL = 3
@ CL = 4
@ CL = 5
tCK
5
8
ns
ns
ns
ns
ns
ns
ns
tCK
3.75
3.75
45
8
tCK
8
Row Active Time
Row Cycle Time
RAS-CAS-Delay
Row Precharge Time
tRAS
tRC
tRCD
tRP
70000
—
60
15
—
15
—
1) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew
Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode.
2) The CK/CK input reference level (for timing reference to CK/CK) is the point at which CK and CK cross. The DQS / DQS, RDQS / RDQS,
input reference level is the crosspoint when in differential strobe mode.
3) Inputs are not recognized as valid until VREF stabilizes. During the period before VREF stabilizes, CKE = 0.2 x VDDQ is recognized as low.
4) The output timing reference voltage level is VTT
.
5) RAS.MAX is calculated from the maximum amount of time a DDR2 device can operate without a refresh command which is equal to 9 x tREFI
t
.
Rev. 1.1, 2007-01
16
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
3.3.2
Timing Parameters
Timing Parameters: Table 15 for DDR2–800; Table 16 for DDR2–667 and Table 17 for DDR2–533C.
TABLE 15
DRAM Component Timing Parameter by Speed Grade - DDR2–800
Parameter
Symbol
DDR2–800
Unit
Note1)2)3)4)5)6)7)
8)
Min.
Max.
9)
DQ output access time from CK / CK
DQS output access time from CK / CK
Average clock high pulse width
Average clock low pulse width
Average clock period
tAC
–400
–350
0.48
+400
+350
0.52
0.52
8000
––
ps
9)
tDQSCK
tCH.AVG
tCL.AVG
tCK.AVG
tDS.BASE
tDH.BASE
ps
10)11)
10)11)
10)11)
12)13)14)
13)14)15)
tCK.AVG
tCK.AVG
ps
0.48
2500
50
DQ and DM input setup time
DQ and DM input hold time
ps
125
––
ps
Control & address input pulse width for each input tIPW
0.6
—
tCK.AVG ––
tCK.AVG ––
DQ and DM input pulse width for each input
Data-out high-impedance time from CK / CK
DQS/DQS low-impedance time from CK / CK
DQ low impedance time from CK/CK
tDIPW
tHZ
tLZ.DQS
tLZ.DQ
0.35
—
9)16)
—
tAC.MAX
tAC.MAX
tAC.MAX
200
ps
ps
ps
ps
ps
9)16)
9)16)
17)
tAC.MIN
2 x tAC.MIN
—
DQS-DQ skew for DQS & associated DQ signals tDQSQ
18)
CK half pulse width
tHP
Min (tCH.ABS
,
__
tCL.ABS
)
19)
20)
DQ hold skew factor
tQHS
tQH
—
300
—
ps
DQ/DQS output hold time from DQS
t
HP – tQHS
ps
Write command to DQS associated clock edges WL
RL – 1
– 0.25
nCK
tCK.AVG
––
21)
DQS latching rising transition to associated clock tDQSS
+ 0.25
edges
DQS input high pulse width
DQS input low pulse width
DQS falling edge to CK setup time
DQS falling edge hold time from CK
Write postamble
tDQSH
tDQSL
tDSS
0.35
0.35
0.2
—
—
—
—
0.6
—
—
—
1.1
0.6
—
—
—
—
tCK.AVG ––
tCK.AVG ––
21)
tCK.AVG
21)
tDSH
0.2
tCK.AVG
tWPST
tWPRE
tIS.BASE
tIH.BASE
tRPRE
tRPST
tCCD
0.4
tCK.AVG ––
Write preamble
0.35
175
250
0.9
tCK.AVG ––
22)23)
Address and control input setup time
Address and control input hold time
Read preamble
ps
23)24)
25)26)
25)27)
ps
tCK.AVG
tCK.AVG
nCK
ns
Read postamble
0.4
CAS to CAS command delay
Write recovery time
2
––
1)
tWR
15
28)29)
1)30)
Auto-Precharge write recovery + precharge time tDAL
WR + tnRP
7.5
nCK
ns
Internal write to read command delay
tWTR
Rev. 1.1, 2007-01
17
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Parameter
Symbol
DDR2–800
Unit
Note1)2)3)4)5)6)7)
8)
Min.
Max.
1)
1)
Internal Read to Precharge command delay
Exit self-refresh to a non-read command
Exit self-refresh to read command
tRTP
tXSNR
tXSRD
tXP
7.5
—
—
—
—
ns
t
RFC +10
ns
200
2
nCK
nCK
––
––
Exit precharge power-down to any valid
command (other than NOP or Deselect)
Exit power down to read command
tXARD
2
—
—
nCK
nCK
––
––
Exit active power-down mode to read command tXARDS
8 – AL
(slow exit, lower power)
31)
CKE minimum pulse width ( high and low pulse tCKE
3
—
nCK
width)
Mode register set command cycle time
MRS command to ODT update delay
OCD drive mode output delay
tMRD
tMOD
tOIT
2
0
0
—
12
12
––
nCK
ns
––
1)
1)
ns
Minimum time clocks remain ON after CKE
asynchronously drops LOW
tDELAY
tIS + tCK .AVG
tIH
+
ns
––
1) For details and notes see the relevant Qimonda component data sheet
2)
DDQ = 1.8 V ± 0.1V; VDD = 1.8 V ± 0.1 V. See notes 5)6)7)8)
V
3) Timing that is not specified is illegal and after such an event, in order to guarantee proper operation, the DRAM must be powered down
and then restarted through the specified initialization sequence before normal operation can continue.
4) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew
Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode.
5) The CK / CK input reference level (for timing reference to CK / CK) is the point at which CK and CK cross. The DQS / DQS, RDQS / RDQS,
input reference level is the crosspoint when in differential strobe mode.
6) Inputs are not recognized as valid until VREF stabilizes. During the period before VREF stabilizes, CKE = 0.2 x VDDQ is recognized as low.
7) The output timing reference voltage level is VTT
.
8) New units, ‘tCK.AVG‘ and ‘nCK‘, are introduced in DDR2–667 and DDR2–800. Unit ‘tCK.AVG‘ represents the actual tCK.AVG of the input clock
under operation. Unit ‘nCK‘ represents one clock cycle of the input clock, counting the actual clock edges. Note that in DDR2–400 and
DDR2–533, ‘tCK‘ is used for both concepts. Example: tXP = 2 [nCK] means; if Power Down exit is registered at Tm, an Active command
may be registered at Tm + 2, even if (Tm + 2 - Tm) is 2 x tCK.AVG + tERR.2PER(Min)
.
9) When the device is operated with input clock jitter, this parameter needs to be derated by the actual tERR(6-10per) of the input clock. (output
deratings are relative to the SDRAM input clock.) For example, if the measured jitter into a DDR2–667 SDRAM has tERR(6-10PER).MIN = – 272
ps and tERR(6- 10PER).MAX = + 293 ps, then tDQSCK.MIN(DERATED) = tDQSCK.MIN – tERR(6-10PER).MAX = – 400 ps – 293 ps = – 693 ps and
tDQSCK.MAX(DERATED) = tDQSCK.MAX – tERR(6-10PER).MIN = 400 ps + 272 ps = + 672 ps. Similarly, tLZ.DQ for DDR2–667 derates to tLZ.DQ.MIN(DERATED)
= - 900 ps – 293 ps = – 1193 ps and tLZ.DQ.MAX(DERATED) = 450 ps + 272 ps = + 722 ps. (Caution on the MIN/MAX usage!)
10) Input clock jitter spec parameter. These parameters are referred to as 'input clock jitter spec parameters' and these parameters apply to
DDR2–667 and DDR2–800 only. The jitter specified is a random jitter meeting a Gaussian distribution.
11) These parameters are specified per their average values, however it is understood that the relationship between the average timing and
the absolute instantaneous timing holds all the times (min. and max of SPEC values are to be used for calculations).
12) Input waveform timing tDS with differential data strobe enabled MR[bit10] = 0, is referenced from the input signal crossing at the VIH.AC level
to the differential data strobe crosspoint for a rising signal, and from the input signal crossing at the VIL.AC level to the differential data strobe
crosspoint for a falling signal applied to the device under test. DQS, DQS signals must be monotonic between Vil(DC)MAX and Vih(DC)MIN. See
Figure 3.
13) If tDS or tDH is violated, data corruption may occur and the data must be re-written with valid data before a valid READ can be executed.
14) These parameters are measured from a data signal ((L/U)DM, (L/U)DQ0, (L/U)DQ1, etc.) transition edge to its respective data strobe signal
((L/U/R)DQS / DQS) crossing.
15) Input waveform timing tDH with differential data strobe enabled MR[bit10] = 0, is referenced from the differential data strobe crosspoint to
the input signal crossing at the VIH.DC level for a falling signal and from the differential data strobe crosspoint to the input signal crossing
at the VIL.DC level for a rising signal applied to the device under test. DQS, DQS signals must be monotonic between VIL.DC.MAX and
VIH.DC.MIN. See Figure 3.
Rev. 1.1, 2007-01
18
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
16) tHZ and tLZ transitions occur in the same access time as valid data transitions. These parameters are referenced to a specific voltage level
which specifies when the device output is no longer driving (tHZ), or begins driving (tLZ) .
17) tDQSQ: Consists of data pin skew and output pattern effects, and p-channel to n-channel variation of the output drivers as well as output
slew rate mismatch between DQS / DQS and associated DQ in any given cycle.
18) tHP is the minimum of the absolute half period of the actual input clock. tHP is an input parameter but not an input specification parameter.
It is used in conjunction with tQHS to derive the DRAM output timing tQH. The value to be used for tQH calculation is determined by the
following equation; tHP = MIN (tCH.ABS, tCL.ABS), where, tCH.ABS is the minimum of the actual instantaneous clock high time; tCL.ABS is the
minimum of the actual instantaneous clock low time.
19) tQHS accounts for: 1) The pulse duration distortion of on-chip clock circuits, which represents how well the actual tHP at the input is
transferred to the output; and 2) The worst case push-out of DQS on one transition followed by the worst case pull-in of DQ on the next
transition, both of which are independent of each other, due to data pin skew, output pattern effects, and pchannel to n-channel variation
of the output drivers.
20) tQH = tHP – tQHS, where: tHP is the minimum of the absolute half period of the actual input clock; and tQHS is the specification value under
the max column. {The less half-pulse width distortion present, the larger the tQH value is; and the larger the valid data eye will be.}
Examples: 1) If the system provides tHP of 1315 ps into a DDR2–667 SDRAM, the DRAM provides tQH of 975 ps minimum. 2) If the system
provides tHP of 1420 ps into a DDR2–667 SDRAM, the DRAM provides tQH of 1080 ps minimum.
21) These parameters are measured from a data strobe signal ((L/U/R)DQS / DQS) crossing to its respective clock signal (CK / CK) crossing.
The spec values are not affected by the amount of clock jitter applied (i.e. tJIT.PER, tJIT.CC, etc.), as these are relative to the clock signal
crossing. That is, these parameters should be met whether clock jitter is present or not.
22) Input waveform timing is referenced from the input signal crossing at the VIH.AC level for a rising signal and VIL.AC for a falling signal applied
to the device under test. See Figure 4.
23) These parameters are measured from a command/address signal (CKE, CS, RAS, CAS, WE, ODT, BA0, A0, A1, etc.) transition edge to
its respective clock signal (CK / CK) crossing. The spec values are not affected by the amount of clock jitter applied (i.e. tJIT.PER, tJIT.CC
,
etc.), as the setup and hold are relative to the clock signal crossing that latches the command/address. That is, these parameters should
be met whether clock jitter is present or not.
24) Input waveform timing is referenced from the input signal crossing at the VIL.DC level for a rising signal and VIH.DC for a falling signal applied
to the device under test. See Figure 4.
25) tRPST end point and tRPRE begin point are not referenced to a specific voltage level but specify when the device output is no longer driving
(tRPST), or begins driving (tRPRE). Figure 2 shows a method to calculate these points when the device is no longer driving (tRPST), or begins
driving (tRPRE) by measuring the signal at two different voltages. The actual voltage measurement points are not critical as long as the
calculation is consistent.
26) When the device is operated with input clock jitter, this parameter needs to be derated by the actual tJIT.PER of the input clock. (output
deratings are relative to the SDRAM input clock.) For example, if the measured jitter into a DDR2–667 SDRAM has tJIT.PER.MIN = – 72 ps
and tJIT.PER.MAX = + 93 ps, then tRPRE.MIN(DERATED) = tRPRE.MIN + tJIT.PER.MIN = 0.9 x tCK.AVG – 72 ps = + 2178 ps and tRPRE.MAX(DERATED) = tRPRE.MAX
+ tJIT.PER.MAX = 1.1 x tCK.AVG + 93 ps = + 2843 ps. (Caution on the MIN/MAX usage!).
27) When the device is operated with input clock jitter, this parameter needs to be derated by the actual tJIT.DUTY of the input clock. (output
deratings are relative to the SDRAM input clock.) For example, if the measured jitter into a DDR2–667 SDRAM has tJIT.DUTY.MIN = – 72 ps
and tJIT.DUTY.MAX = + 93 ps, then tRPST.MIN(DERATED) = tRPST.MIN + tJIT.DUTY.MIN = 0.4 x tCK.AVG – 72 ps = + 928 ps and tRPST.MAX(DERATED) = tRPST.MAX
+ tJIT.DUTY.MAX = 0.6 x tCK.AVG + 93 ps = + 1592 ps. (Caution on the MIN/MAX usage!).
28) DAL = WR + RU{tRP(ns) / tCK(ns)}, where RU stands for round up. WR refers to the tWR parameter stored in the MRS. For tRP, if the result
of the division is not already an integer, round up to the next highest integer. tCK refers to the application clock period. Example: For
DDR2–533 at tCK = 3.75 ns with tWR programmed to 4 clocks. tDAL = 4 + (15 ns / 3.75 ns) clocks = 4 + (4) clocks = 8 clocks.
29) tDAL.nCK = WR [nCK] + tnRP.nCK = WR + RU{tRP [ps] / tCK.AVG[ps] }, where WR is the value programmed in the EMR.
30) tWTR is at lease two clocks (2 x tCK) independent of operation frequency.
31) tCKE.MIN of 3 clocks means CKE must be registered on three consecutive positive clock edges. CKE must remain at the valid input level the
entire time it takes to achieve the 3 clocks of registration. Thus, after any CKE transition, CKE may not transition from its valid level during
the time period of tIS + 2 x tCK + tIH.
Rev. 1.1, 2007-01
19
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
TABLE 16
DRAM Component Timing Parameter by Speed Grade - DDR2–667
Parameter
Symbol
DDR2–667
Unit
Note1)2)3)4)5)6)7)
8)
Min.
Max.
9)
DQ output access time from CK / CK
DQS output access time from CK / CK
Average clock high pulse width
Average clock low pulse width
Average clock period
tAC
–450
–400
0.48
+450
+400
0.52
0.52
8000
––
ps
9)
tDQSCK
tCH.AVG
tCL.AVG
tCK.AVG
tDS.BASE
tDH.BASE
ps
10)11)
10)11)
tCK.AVG
tCK.AVG
ps
0.48
3000
100
––
12)13)14)
DQ and DM input setup time
DQ and DM input hold time
ps
13)14)15)
175
––
ps
Control & address input pulse width for each input tIPW
0.6
—
tCK.AVG ––
tCK.AVG ––
DQ and DM input pulse width for each input
Data-out high-impedance time from CK / CK
DQS/DQS low-impedance time from CK / CK
DQ low impedance time from CK/CK
tDIPW
tHZ
tLZ.DQS
tLZ.DQ
0.35
—
9)16)
—
tAC.MAX
tAC.MAX
tAC.MAX
240
ps
ps
ps
ps
ps
9)16)
9)16)
17)
tAC.MIN
2 x tAC.MIN
—
DQS-DQ skew for DQS & associated DQ signals tDQSQ
18)
CK half pulse width
tHP
Min (tCH.ABS
,
__
tCL.ABS
)
19)
20)
DQ hold skew factor
tQHS
tQH
—
340
—
ps
DQ/DQS output hold time from DQS
t
HP – tQHS
ps
Write command to DQS associated clock edges WL
RL–1
nCK
tCK.AVG
––
21)
DQS latching rising transition to associated clock tDQSS
– 0.25
+ 0.25
edges
DQS input high pulse width
DQS input low pulse width
DQS falling edge to CK setup time
DQS falling edge hold time from CK
Write postamble
tDQSH
tDQSL
tDSS
0.35
0.35
0.2
—
—
—
—
0.6
—
—
—
1.1
0.6
—
—
—
—
—
—
—
tCK.AVG ––
tCK.AVG ––
21)
tCK.AVG
21)
tDSH
0.2
tCK.AVG
tWPST
tWPRE
tIS.BASE
tIH.BASE
tRPRE
tRPST
tCCD
0.4
tCK.AVG ––
Write preamble
0.35
200
275
0.9
tCK.AVG ––
22)23)
Address and control input setup time
Address and control input hold time
Read preamble
ps
23)24)
25)26)
25)27)
ps
tCK.AVG
tCK.AVG
nCK
ns
Read postamble
0.4
CAS to CAS command delay
Write recovery time
2
––
1)
tWR
15
28)29)
1)30)
1)
Auto-Precharge write recovery + precharge time tDAL
WR + tnRP
7.5
nCK
ns
Internal write to read command delay
Internal Read to Precharge command delay
Exit self-refresh to a non-read command
Exit self-refresh to read command
tWTR
tRTP
tXSNR
tXSRD
7.5
ns
1)
t
RFC +10
ns
200
nCK
––
Rev. 1.1, 2007-01
20
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Parameter
Symbol
DDR2–667
Unit
Note1)2)3)4)5)6)7)
8)
Min.
Max.
Exit precharge power-down to any valid
command (other than NOP or Deselect)
tXP
2
—
nCK
––
Exit power down to read command
tXARD
2
—
—
nCK
nCK
––
––
Exit active power-down mode to read command tXARDS
7 – AL
(slow exit, lower power)
31)
CKE minimum pulse width ( high and low pulse tCKE
3
—
nCK
width)
Mode register set command cycle time
MRS command to ODT update delay
OCD drive mode output delay
tMRD
tMOD
tOIT
2
0
0
—
12
12
––
nCK
ns
––
1)
1)
ns
Minimum time clocks remain ON after CKE
asynchronously drops LOW
tDELAY
tIS + tCK .AVG
tIH
+
ns
––
1) For details and notes see the relevant Qimonda component data sheet
2)
DDQ = 1.8 V ± 0.1V; VDD = 1.8 V ± 0.1 V. See notes 5)6)7)8)
V
3) Timing that is not specified is illegal and after such an event, in order to guarantee proper operation, the DRAM must be powered down
and then restarted through the specified initialization sequence before normal operation can continue.
4) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew
Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode.
5) The CK / CK input reference level (for timing reference to CK / CK) is the point at which CK and CK cross. The DQS / DQS, RDQS / RDQS,
input reference level is the crosspoint when in differential strobe mode.
6) Inputs are not recognized as valid until VREF stabilizes. During the period before VREF stabilizes, CKE = 0.2 x VDDQ is recognized as low.
7) The output timing reference voltage level is VTT
.
8) New units, ‘tCK.AVG‘ and ‘nCK‘, are introduced in DDR2–667 and DDR2–800. Unit ‘tCK.AVG‘ represents the actual tCK.AVG of the input clock
under operation. Unit ‘nCK‘ represents one clock cycle of the input clock, counting the actual clock edges. Note that in DDR2–400 and
DDR2–533, ‘tCK‘ is used for both concepts. Example: tXP = 2 [nCK] means; if Power Down exit is registered at Tm, an Active command
may be registered at Tm + 2, even if (Tm + 2 - Tm) is 2 x tCK.AVG + tERR.2PER(Min)
.
9) When the device is operated with input clock jitter, this parameter needs to be derated by the actual tERR(6-10per) of the input clock. (output
deratings are relative to the SDRAM input clock.) For example, if the measured jitter into a DDR2–667 SDRAM has tERR(6-10PER).MIN = – 272
ps and tERR(6- 10PER).MAX = + 293 ps, then tDQSCK.MIN(DERATED) = tDQSCK.MIN – tERR(6-10PER).MAX = – 400 ps – 293 ps = – 693 ps and
tDQSCK.MAX(DERATED) = tDQSCK.MAX – tERR(6-10PER).MIN = 400 ps + 272 ps = + 672 ps. Similarly, tLZ.DQ for DDR2–667 derates to tLZ.DQ.MIN(DERATED)
= - 900 ps – 293 ps = – 1193 ps and tLZ.DQ.MAX(DERATED) = 450 ps + 272 ps = + 722 ps. (Caution on the MIN/MAX usage!)
10) Input clock jitter spec parameter. These parameters are referred to as 'input clock jitter spec parameters' and these parameters apply to
DDR2–667 and DDR2–800 only. The jitter specified is a random jitter meeting a Gaussian distribution.
11) These parameters are specified per their average values, however it is understood that the relationship between the average timing and
the absolute instantaneous timing holds all the times (min. and max of SPEC values are to be used for calculations).
12) Input waveform timing tDS with differential data strobe enabled MR[bit10] = 0, is referenced from the input signal crossing at the VIH.AC level
to the differential data strobe crosspoint for a rising signal, and from the input signal crossing at the VIL.AC level to the differential data strobe
crosspoint for a falling signal applied to the device under test. DQS, DQS signals must be monotonic between Vil(DC)MAX and Vih(DC)MIN. See
Figure 3.
13) If tDS or tDH is violated, data corruption may occur and the data must be re-written with valid data before a valid READ can be executed.
14) These parameters are measured from a data signal ((L/U)DM, (L/U)DQ0, (L/U)DQ1, etc.) transition edge to its respective data strobe signal
((L/U/R)DQS / DQS) crossing.
15) Input waveform timing tDH with differential data strobe enabled MR[bit10] = 0, is referenced from the differential data strobe crosspoint to
the input signal crossing at the VIH.DC level for a falling signal and from the differential data strobe crosspoint to the input signal crossing
at the VIL.DC level for a rising signal applied to the device under test. DQS, DQS signals must be monotonic between VIL.DC.MAX and
VIH.DC.MIN. See Figure 3.
16) tHZ and tLZ transitions occur in the same access time as valid data transitions. These parameters are referenced to a specific voltage level
which specifies when the device output is no longer driving (tHZ), or begins driving (tLZ) .
17) tDQSQ: Consists of data pin skew and output pattern effects, and p-channel to n-channel variation of the output drivers as well as output
slew rate mismatch between DQS / DQS and associated DQ in any given cycle.
Rev. 1.1, 2007-01
21
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
18) tHP is the minimum of the absolute half period of the actual input clock. tHP is an input parameter but not an input specification parameter.
It is used in conjunction with tQHS to derive the DRAM output timing tQH. The value to be used for tQH calculation is determined by the
following equation; tHP = MIN (tCH.ABS, tCL.ABS), where, tCH.ABS is the minimum of the actual instantaneous clock high time; tCL.ABS is the
minimum of the actual instantaneous clock low time.
19) tQHS accounts for: 1) The pulse duration distortion of on-chip clock circuits, which represents how well the actual tHP at the input is
transferred to the output; and 2) The worst case push-out of DQS on one transition followed by the worst case pull-in of DQ on the next
transition, both of which are independent of each other, due to data pin skew, output pattern effects, and pchannel to n-channel variation
of the output drivers.
20) tQH = tHP – tQHS, where: tHP is the minimum of the absolute half period of the actual input clock; and tQHS is the specification value under
the max column. {The less half-pulse width distortion present, the larger the tQH value is; and the larger the valid data eye will be.}
Examples: 1) If the system provides tHP of 1315 ps into a DDR2–667 SDRAM, the DRAM provides tQH of 975 ps minimum. 2) If the system
provides tHP of 1420 ps into a DDR2–667 SDRAM, the DRAM provides tQH of 1080 ps minimum.
21) These parameters are measured from a data strobe signal ((L/U/R)DQS / DQS) crossing to its respective clock signal (CK / CK) crossing.
The spec values are not affected by the amount of clock jitter applied (i.e. tJIT.PER, tJIT.CC, etc.), as these are relative to the clock signal
crossing. That is, these parameters should be met whether clock jitter is present or not.
22) Input waveform timing is referenced from the input signal crossing at the VIH.AC level for a rising signal and VIL.AC for a falling signal applied
to the device under test. See Figure 4.
23) These parameters are measured from a command/address signal (CKE, CS, RAS, CAS, WE, ODT, BA0, A0, A1, etc.) transition edge to
its respective clock signal (CK / CK) crossing. The spec values are not affected by the amount of clock jitter applied (i.e. tJIT.PER, tJIT.CC
,
etc.), as the setup and hold are relative to the clock signal crossing that latches the command/address. That is, these parameters should
be met whether clock jitter is present or not.
24) Input waveform timing is referenced from the input signal crossing at the VIL.DC level for a rising signal and VIH.DC for a falling signal applied
to the device under test. See Figure 4.
25) tRPST end point and tRPRE begin point are not referenced to a specific voltage level but specify when the device output is no longer driving
(tRPST), or begins driving (tRPRE). Figure 2 shows a method to calculate these points when the device is no longer driving (tRPST), or begins
driving (tRPRE) by measuring the signal at two different voltages. The actual voltage measurement points are not critical as long as the
calculation is consistent.
26) When the device is operated with input clock jitter, this parameter needs to be derated by the actual tJIT.PER of the input clock. (output
deratings are relative to the SDRAM input clock.) For example, if the measured jitter into a DDR2–667 SDRAM has tJIT.PER.MIN = – 72 ps
and tJIT.PER.MAX = + 93 ps, then tRPRE.MIN(DERATED) = tRPRE.MIN + tJIT.PER.MIN = 0.9 x tCK.AVG – 72 ps = + 2178 ps and tRPRE.MAX(DERATED) = tRPRE.MAX
+ tJIT.PER.MAX = 1.1 x tCK.AVG + 93 ps = + 2843 ps. (Caution on the MIN/MAX usage!).
27) When the device is operated with input clock jitter, this parameter needs to be derated by the actual tJIT.DUTY of the input clock. (output
deratings are relative to the SDRAM input clock.) For example, if the measured jitter into a DDR2–667 SDRAM has tJIT.DUTY.MIN = – 72 ps
and tJIT.DUTY.MAX = + 93 ps, then tRPST.MIN(DERATED) = tRPST.MIN + tJIT.DUTY.MIN = 0.4 x tCK.AVG – 72 ps = + 928 ps and tRPST.MAX(DERATED) = tRPST.MAX
+ tJIT.DUTY.MAX = 0.6 x tCK.AVG + 93 ps = + 1592 ps. (Caution on the MIN/MAX usage!).
28) DAL = WR + RU{tRP(ns) / tCK(ns)}, where RU stands for round up. WR refers to the tWR parameter stored in the MRS. For tRP, if the result
of the division is not already an integer, round up to the next highest integer. tCK refers to the application clock period. Example: For
DDR2–533 at tCK = 3.75 ns with tWR programmed to 4 clocks. tDAL = 4 + (15 ns / 3.75 ns) clocks = 4 + (4) clocks = 8 clocks.
29) tDAL.nCK = WR [nCK] + tnRP.nCK = WR + RU{tRP [ps] / tCK.AVG[ps] }, where WR is the value programmed in the EMR.
30) tWTR is at lease two clocks (2 x tCK) independent of operation frequency.
31) tCKE.MIN of 3 clocks means CKE must be registered on three consecutive positive clock edges. CKE must remain at the valid input level the
entire time it takes to achieve the 3 clocks of registration. Thus, after any CKE transition, CKE may not transition from its valid level during
the time period of tIS + 2 x tCK + tIH.
Rev. 1.1, 2007-01
22
08212006-PKYN-2H1B
5(ꢀꢀEHJLꢀQꢀSRLQWꢀ
7
ꢀ
Hꢀ
ꢀSRLꢀQW
ꢀ
92/
ꢀꢍꢀꢄ[ꢀP9
ꢀꢍꢀ[ꢀP9
ꢀ
977ꢀꢈꢀ[ꢀP
9ꢀ
92/
ꢀ
977ꢀꢈꢀꢄ[ꢀP9ꢀ
7ꢂꢀ 7ꢄꢀ
W+=ꢎW536
7ꢀꢀHQG
ꢀSRLQ
Wꢀꢀ
ꢀꢄꢏ
7ꢂꢈ7ꢄꢀ
W/=ꢎW
535(ꢀEꢀ
Wꢀꢀ
ꢀꢄꢏ7
ꢂꢈ7ꢄꢀ
'46ꢀ
W'+ꢀ
W'6ꢀ
ꢀ
9,ꢀ+ꢐDFꢑꢀꢀPLQ
9,ꢀ+ꢐGFꢑꢀꢀPLQ
95ꢀ ()ꢐGFꢑꢀ
ꢀ
ꢀ
9,ꢀ/ꢐGFꢑꢀꢀPD[
9,ꢀ/ꢐDFꢑꢀꢀPD[
96ꢀ 6ꢀ
ꢀ
ꢀ
W,+ꢀ
W,+
ꢀ
W,6ꢀ
W,6ꢀ
ꢀ
ꢑꢀ
ꢑꢀ
9,ꢀ/ꢐGF ꢀPD[
ꢀ
ꢀ
ꢑꢀ
9,ꢀ/ꢐDF ꢀPD[
ꢑꢀ
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
FIGURE 2
Method for calculating transitions and endpoint
92+
ꢀꢈꢀ[ꢀP9
ꢀ
977ꢀꢍꢀꢄ[ꢀP9ꢀ
977ꢀꢍꢀ[ꢀP9ꢀ
92+
ꢀꢈꢀꢄ[ꢀP9ꢀ
W/=ꢀ
W53
W+=ꢀ
W536 QG
7ꢂꢀ 7ꢄꢀ
HJLQꢀSRLQ
FIGURE 3
Differential input waveform timing - tDS and tDS
'46ꢀ
W'+ꢀ
W'6ꢀ
9'ꢀ '4
FIGURE 4
Differential input waveform timing - tlS and tlH
&.ꢀ
&.ꢀ
9'ꢀ '4
9,ꢀ+ꢐDF ꢀPLQꢀ
9,ꢀ+ꢐGF ꢀPLQꢀ
95ꢀ ()ꢐGFꢑꢀ
96ꢀ 6ꢀ
Rev. 1.1, 2007-01
23
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
TABLE 17
DRAM Component Timing Parameter by Speed Grade - DDR2–533
Parameter
Symbol
DDR2–533
Unit
Note1)2)3)4)5)
6)7)
Min.
Max.
DQ output access time from CK / CK
CAS A to CAS B command period
CK, CK high-level width
tAC
–500
2
+500
—
ps
—
—
—
—
tCCD
tCH
tCKE
tCL
tCK
tCK
tCK
tCK
tCK
0.45
3
0.55
—
CKE minimum high and low pulse width
CK, CK low-level width
0.45
WR + tRP
0.55
—
—
8)18)
Auto-Precharge write recovery + precharge
time
tDAL
9)
Minimum time clocks remain ON after CKE
asynchronously drops LOW
tDELAY
tIS + tCK + tIH
225
––
––
—
ns
ps
ps
10)
11)
DQ and DM input hold time (differential data
strobe)
t
t
DH (base)
DQ and DM input hold time (single ended data
strobe)
DH1 (base)
–25
DQ and DM input pulse width (each input)
DQS output access time from CK / CK
tDIPW
0.35
–450
0.35
—
—
tCK
ps
tCK
ps
—
—
tDQSCK
+450
—
DQS input low (high) pulse width (write cycle) tDQSL,H
—
11)
DQS-DQ skew (for DQS & associated DQ
signals)
tDQSQ
300
Write command to 1st DQS latching transition tDQSS
– 0.25
100
+ 0.25
—
tCK
—
11)
DQ and DM input setup time (differential data
strobe)
t
DS (base)
ps
11)
DQ and DM input setup time (single ended data tDS1 (base)
strobe)
–25
0.2
—
—
—
ps
DQS falling edge hold time from CK (write
cycle)
tDSH
tCK
tCK
—
DQS falling edge to CK setup time (write cycle) tDSS
0.2
—
12)
Clock half period
tHP
MIN. (tCL, tCH)
13)
11)
Data-out high-impedance time from CK / CK
Address and control input hold time
tHZ
—
tAC.MAX
—
ps
ps
tCK
tIH(base)
tIPW
375
0.6
Address and control input pulse width
(each input)
—
—
11)
14)
14)
Address and control input setup time
DQ low-impedance time from CK / CK
DQS low-impedance from CK / CK
Mode register set command cycle time
OCD drive mode output delay
tIS(base)
tLZ(DQ)
tLZ(DQS)
tMRD
250
—
ps
ps
ps
tCK
ns
2 × tAC.MIN
tAC.MAX
tAC.MAX
—
tAC.MIN
2
0
—
—
—
—
tOIT
12
Data output hold time from DQS
Data hold skew factor
tQH
t
HP –tQHS
—
tQHS
—
400
ps
Rev. 1.1, 2007-01
24
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Parameter
Symbol
DDR2–533
Min.
Unit
Note1)2)3)4)5)
6)7)
Max.
14)15)
16)18)
17)
Average periodic refresh Interval
tREFI
tRFC
—
7.8
3.9
—
µs
µs
ns
—
Auto-Refresh to Active/Auto-Refresh
command period
105
Precharge-All (4 banks) command period
Precharge-All (8 banks) command period
Read preamble
tRP
t
RP + 1tCK
—
ns
ns
tCK
tCK
ns
ns
ns
tCK
tCK
ns
—
tRP
15 + 1tCK
0.9
—
—
14)
tRPRE
tRPST
tRRD
1.1
0.60
—
14)
Read postamble
0.40
7.5
14)18)
16)20)
Active bank A to Active bank B command
period
10
—
Internal Read to Precharge command delay
Write preamble
tRTP
7.5
—
—
tWPRE
tWPST
tWR
0.25 x tCK
0.40
15
—
—
19)
Write postamble
0.60
—
Write recovery time for write without Auto-
Precharge
—
20)
Write recovery time for write with Auto-
Precharge
WR
t
WR/tCK
tCK
21)
22)
Internal Write to Read command delay
tWTR
7.5
2
—
—
ns
Exit power down to any valid command
(other than NOP or Deselect)
tXARD
tCK
22)
Exit active power-down mode to Read
command (slow exit, lower power)
tXARDS
tXP
6 – AL
2
—
—
tCK
tCK
Exit precharge power-down to any valid
command (other than NOP or Deselect)
—
Exit Self-Refresh to non-Read command
Exit Self-Refresh to Read command
tXSNR
tXSRD
t
RFC +10
—
—
ns
—
—
200
tCK
1) For details and notes see the relevant Qimonda component data sheet
2)
DDQ = 1.8 V ± 0.1 V; VDD = 1.8 V ±0.1 V. See notes 5)6)7)8)
V
3) Timing that is not specified is illegal and after such an event, in order to guarantee proper operation, the DRAM must be powered down
and then restarted through the specified initialization sequence before normal operation can continue.
4) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew
Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode.
5) The CK / CK input reference level (for timing reference to CK / CK) is the point at which CK and CK cross. The DQS / DQS, RDQS/ RDQS,
input reference level is the crosspoint when in differential strobe mode.
6) Inputs are not recognized as valid until VREF stabilizes. During the period before VREF stabilizes, CKE = 0.2 x VDDQ is recognized as low.
7) The output timing reference voltage level is VTT
.
8) For each of the terms, if not already an integer, round to the next highest integer. tCK refers to the application clock period. WR refers to
the WR parameter stored in the MR.
9) The clock frequency is allowed to change during self-refresh mode or precharge power-down mode.
10) For timing definition, refer to the Component data sheet.
11) Consists of data pin skew and output pattern effects, and p-channel to n-channel variation of the output drivers as well as output Slew Rate
mis-match between DQS / DQS and associated DQ in any given cycle.
12) MIN (tCL, tCH) refers to the smaller of the actual clock low time and the actual clock high time as provided to the device (i.e. this value can
be greater than the minimum specification limits for tCL and tCH).
Rev. 1.1, 2007-01
25
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
13) The tHZ, tRPST and tLZ, tRPRE parameters are referenced to a specific voltage level, which specify when the device output is no longer driving
(tHZ, tRPST), or begins driving (tLZ, tRPRE). tHZ and tLZ transitions occur in the same access time windows as valid data transitions.These
parameters are verified by design and characterization, but not subject to production test.
14) The Auto-Refresh command interval has be reduced to 3.9 µs when operating the DDR2 DRAM in a temperature range between 85 °C
and 95 °C.
15) 0 °C≤ TCASE ≤ 85 °C
16) 85 °C < TCASE ≤ 95 °C
17) A maximum of eight Auto-Refresh commands can be posted to any given DDR2 SDRAM device.
18) The tRRD timing parameter depends on the page size of the DRAM organization. See Table 2 “Ordering Information for RoHS
Compliant Products” on Page 4.
19) The maximum limit for the tWPST parameter is not a device limit. The device operates with a greater value for this parameter, but system
performance (bus turnaround) degrades accordingly.
20) WR must be programmed to fulfill the minimum requirement for the tWR timing parameter, where WRMIN[cycles] = tWR(ns)/tCK(ns) rounded
up to the next integer value. tDAL = WR + (tRP/tCK). For each of the terms, if not already an integer, round to the next highest integer. tCK
refers to the application clock period. WR refers to the WR parameter stored in the MRS.
21) Minimum tWTR is two clocks when operating the DDR2-SDRAM at frequencies ≤ 200 ΜΗz.
22) User can choose two different active power-down modes for additional power saving via MRS address bit A12. In “standard active power-
down mode” (MR, A12 = “0”) a fast power-down exit timing tXARD can be used. In “low active power-down mode” (MR, A12 =”1”) a slow
power-down exit timing tXARDS has to be satisfied.
3.3.3
ODT AC Electrical Characteristics
ODT AC Character. and Opeating Conditions: Table 18– DDR2–667 &DDR2–800 and Table 19– DDR2–533C & DDR2–400B
TABLE 18
ODT AC Character. and Operating Conditions for DDR2-667 & DDR2-800
Symbol
Parameter / Condition
Values
Unit
Note
Min.
Max.
1)
tAOND
tAON
ODT turn-on delay
2
2
nCK
ns
1)2)
1)
ODT turn-on
tAC.MIN
tAC.MAX + 0.7 ns
tAONPD
tAOFD
tAOF
ODT turn-on (Power-Down Modes)
ODT turn-off delay
t
AC.MIN + 2 ns
2 tCK +
t
AC.MAX + 1 ns
ns
1)
2.5
2.5
nCK
ns
1)3)
1)
ODT turn-off
tAC.MIN
tAC.MAX + 0.6 ns
tAOFPD
tANPD
tAXPD
ODT turn-off (Power-Down Modes)
ODT to Power Down Mode Entry Latency
ODT Power Down Exit Latency
t
AC.MIN + 2 ns
2.5 tCK +
tAC.MAX + 1 ns
ns
1)
3
8
—
—
nCK
nCK
1)
1) New units, 'tCK.AVG' and 'nCK', are introduced in DDR2-667 and DDR2-800. Unit 'tCK.AVG' represents the actual tCK.AVG of the input clock
under operation. Unit 'nCK' represents one clock cycle of the input clock, counting the actual clock edges. Note that in DDR2-400 and
DDR2-533, 'tCK' is used for both concepts. Example: tXP = 2 [nCK] means; if Power Down exit is registered at Tm, an Active command may
be registered at Tm + 2, even if (Tm + 2 - Tm) is 2 × tCK.AVG+ tEPR.2PER(MIN)
.
2) ODT turn on time min is when the device leaves high impedance and ODT resistance begins to turn on. ODT turn on time max is when the
ODT resistance is fully on. Both are measured from tAOND, which is interpreted differently per speed bin. For DDR2-667/800, tAOND is 2 clock
cycles after the clock edge that registered a first ODT HIGH counting the actual input clock edges.
3) ODT turn off time min. is when the device starts to turn off ODT resistance. ODT turn off time max is when the bus is in high impedance.
Both are measured from tAOFD. Both are measured from tAOFD, which is interpreted differently per speed bin. For DDR2-667/800,if tCK.AVG
=
3 ns is assumed, tAOFD= 1.5 ns (0.5 × 3 ns) after the second trailing clock edge counting from the clock edge that registered a first ODT
LOW and by counting the actual input clock edge.
Rev. 1.1, 2007-01
26
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
TABLE 19
ODT AC Character. and Operating Conditions for DDR2-533 & DDR2-400
Symbol
Parameter / Condition
Values
Unit
Note
Min.
Max.
tAOND
tAON
ODT turn-on delay
2
2
tCK
ns
ns
tCK
ns
ns
tCK
tCK
—
1)
ODT turn-on
tAC.MIN
tAC.MAX + 1 ns
tAONPD
tAOFD
tAOF
ODT turn-on (Power-Down Modes)
ODT turn-off delay
t
AC.MIN + 2 ns
2 tCK +
t
AC.MAX + 1 ns
—
2.5
2.5
—
2)
ODT turn-off
tAC.MIN
tAC.MAX + 0.6 ns
tAOFPD
tANPD
tAXPD
ODT turn-off (Power-Down Modes)
ODT to Power Down Mode Entry Latency
ODT Power Down Exit Latency
t
AC.MIN + 2 ns
2.5 tCK +
tAC.MAX + 1 ns
—
—
—
3
8
—
—
1) ODT turn on time min is when the device leaves high impedance and ODT resistance begins to turn on. ODT turn on time max is when the
ODT resistance is fully on. Both are measured from tAOND, which is interpreted differently per speed bin. For DDR2-400/533, tAOND is 10 ns
(= 2 x 5 ns) after the clock edge that registered a first ODT HIGH if tCK = 5 ns.
2) ODT turn off time min. is when the device starts to turn off ODT resistance. ODT turn off time max is when the bus is in high impedance.
Both are measured from tAOFD. Both are measured from tAOFD, which is interpreted differently per speed bin. For DDR2-400/533, tAOFD is
12.5 ns (= 2.5 x 5 ns) after the clock edge that registered a first ODT HIGH if tCK = 5 ns.
Rev. 1.1, 2007-01
27
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
3.4
IDD Specifications and Conditions
List of tables defining IDD Specifications and Conditions.
•
•
•
•
•
•
•
Table 20 “IDD Measurement Conditions” on Page 28
Table 21 “Definitions for IDD” on Page 29
Table 22 “IDD Specification for HYS64T[32/64/128]xxxEDL–25F–B2” on Page 30
Table 23 “IDD Specification for HYS64T[32/64/128]xxxEDL–2.5–B2” on Page 31
Table 24 “IDD Specification for HYS64T[32/64/128]xxxEDL–3–B2” on Page 32
Table 25 “IDD Specification for HYS64T[32/64/128]xxxEDL–3S–B2” on Page 33
Table 26 “IDD Specification for HYS64T[32/64/128]xxxEDL–3.7–B2” on Page 34
TABLE 20
DD Measurement Conditions
I
Parameter
Symbol Note
1)2)3)4)5)
Operating Current 0
IDD0
—
One bank Active - Precharge; tCK = tCK.MIN, tRC = tRC.MIN, tRAS = tRAS.MIN, CKE is HIGH, CS is HIGH between
valid commands. Address and control inputs are SWITCHING, Databus inputs are SWITCHING.
6)
Operating Current 1
IDD1
One bank Active - Read - Precharge; IOUT = 0 mA, BL = 4, tCK = tCK.MIN, tRC = tRC.MIN, tRAS = tRAS.MIN
,
t
RCD = tRCD.MIN, AL = 0, CL = CLMIN; CKE is HIGH, CS is HIGH between valid commands. Address and
control inputs are SWITCHING, Databus inputs are SWITCHING.
Precharge Standby Current
IDD2N
—
All banks idle; CS is HIGH; CKE is HIGH; tCK = tCK.MIN; Other control and address inputs are SWITCHING,
Databus inputs are SWITCHING.
Precharge Power-Down Current
Other control and address inputs are STABLE, Data bus inputs are FLOATING.
IDD2P
IDD2Q
—
—
Precharge Quiet Standby Current
All banks idle; CS is HIGH; CKE is HIGH; tCK = tCK.MIN; Other control and address inputs are STABLE,
Data bus inputs are FLOATING.
Active Standby Current
Burst Read: All banks open; Continuous burst reads; BL = 4; AL = 0, CL = CLMIN; tCK = tCK.MIN
IDD3N
—
—
;
t
RAS = tRAS.MAX, tRP = tRP.MIN; CKE is HIGH, CS is HIGH between valid commands. Address inputs are
SWITCHING; Data Bus inputs are SWITCHING; IOUT = 0 mA.
Active Power-Down Current
All banks open; tCK = tCK.MIN, CKE is LOW; Other control and address inputs are STABLE, Data bus inputs
are FLOATING. MRS A12 bit is set to LOW (Fast Power-down Exit);
IDD3P(0)
IDD3P(1)
IDD4R
Active Power-Down Current
All banks open; tCK = tCK.MIN, CKE is LOW; Other control and address inputs are STABLE, Data bus inputs
are FLOATING. MRS A12 bit is set to HIGH (Slow Power-down Exit);
—
6)
Operating Current - Burst Read
All banks open; Continuous burst reads; BL = 4; AL = 0, CL = CLMIN; tCK = tCKMIN; tRAS = tRASMAX
;
t
RP = tRPMIN; CKE is HIGH, CS is HIGH between valid commands; Address inputs are SWITCHING; Data
bus inputs are SWITCHING; IOUT = 0mA.
Operating Current - Burst Write
IDD4W
—
All banks open; Continuous burst writes; BL = 4; AL = 0, CL = CLMIN; tCK = tCK.MIN
;
t
RAS = tRAS.MAX., tRP = tRP.MAX; CKE is HIGH, CS is HIGH between valid commands. Address inputs are
SWITCHING; Data Bus inputs are SWITCHING;
Rev. 1.1, 2007-01
28
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Parameter
Symbol Note
1)2)3)4)5)
Burst Refresh Current
IDD5B
IDD5D
IDD6
—
—
t
CK = tCK.MIN., Refresh command every tRFC = tRFC.MIN interval, CKE is HIGH, CS is HIGH between valid
commands, Other control and address inputs are SWITCHING, Data bus inputs are SWITCHING.
Distributed Refresh Current
t
CK = tCK.MIN., Refresh command every tRFC = tREFI interval, CKE is LOW and CS is HIGH between valid
commands, Other control and address inputs are SWITCHING, Data bus inputs are SWITCHING.
Self-Refresh Current
—
CKE ≤ 0.2 V; external clock off, CK and CK at 0 V; Other control and address inputs are FLOATING, Data
bus inputs are FLOATING. IDD6 current values are guaranteed up to TCASE of 85 °C max.
6)
All Bank Interleave Read Current
IDD7
All banks are being interleaved at minimum tRC without violating tRRD using a burst length of 4. Control
and address bus inputs are STABLE during DESELECTS. Iout = 0 mA.
1)
2)
V
DDQ = 1.8 V ± 0.1 V; VDD = 1.8 V ± 0.1 V
IDD specifications are tested after the device is properly initialized and IDD parameter are specified with ODT disabled.
3) Definitions for IDD see Table 3
4) For two rank modules: for all active current measurements the other rank is in Precharge Power-Down Mode IDD2P
5) For details and notes see the relevant Qimonda component data sheet
6)
IDD1, IDD4R and IDD7 current measurements are defined with the outputs disabled (IOUT = 0 mA). To achieve this on module level the output
buffers can be disabled using an EMRS(1) (Extended Mode Register Command) by setting A12 bit to HIGH.
TABLE 21
Definitions for IDD
Parameter
LOW
Description
VIN ≤ VIL(ac).MAX, HIGH is defined as VIN ≥ VIH(ac).MIN
Inputs are stable at a HIGH or LOW level
Inputs are VREF = VDDQ /2
STABLE
FLOATING
SWITCHING
Inputs are changing between HIGH and LOW every other clock (once per 2 cycles) for address and control
signals, and inputs changing between HIGH and LOW every other data transfer (once per cycle) for DQ
signals not including mask or strobes
Rev. 1.1, 2007-01
29
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
TABLE 22
DD Specification for HYS64T[32/64/128]xxxEDL–25F–B2
I
Product Type
Unit
Note1)
Organization
256 MB
1 Rank
× 64
512 MB
2 Ranks
× 64
1 GB
2 Ranks
× 64
–25F
–25F
–25F
Symbol
Max.
Max.
Max.
2)
IDD0
420
480
204
36
456
516
408
72
744
872
816
144
720
960
624
208
1312
1312
1232
176
80
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
2)
IDD1
3)
IDD2N
3)
IDD2P
3)
IDD2Q
IDD3N
180
240
156
52
360
480
312
104
756
836
616
88
3)
4)3)
5)3)
2)
IDD3P_0 (fast)
IDD3P_1 (slow)
IDD4R
720
800
580
44
2)
IDD4W
IDD5B
2)
3)6)
3)6)
2)
IDD5D
IDD6
24
40
IDD7
1060
1096
1432
1) Calculated values from component data. ODT disabled. IDD1,
I
DD4R, and IDD7, are defined with the outputs disabled.
2) The other rank is in IDD2P Precharge Power-Down Current mode
3) Both ranks are in the same IDD current mode
4) Fast: MRS(12)=0
5) Slow: MRS(12)=1
6)
IDD5D and IDD6 values are for 0°C ≤ TCase ≤ 85°C
Rev. 1.1, 2007-01
30
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
TABLE 23
DD Specification for HYS64T[32/64/128]xxxEDL–2.5–B2
I
Product Type
Unit
Note1)
Organization
256 MB
1 Rank
× 64
512 MB
1 GB
2 Ranks
× 64
2 Ranks
× 64
–2.5
–2.5
–2.5
Symbol
Max.
Max.
Max.
2)
IDD0
400
460
204
36
436
496
408
72
712
832
816
144
720
960
624
208
1312
1312
1232
176
80
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
2)
IDD1
3)
IDD2N
3)
IDD2P
3)
IDD2Q
IDD3N
180
240
156
52
360
480
312
104
756
836
616
88
3)
4)3)
5)3)
2)
IDD3P_0 (fast)
IDD3P_1 (slow)
IDD4R
720
800
580
44
2)
IDD4W
IDD5B
2)
3)6)
3)6)
2)
IDD5D
IDD6
24
40
IDD7
1020
1056
1352
1) Calculated values from component data. ODT disabled. IDD1,
I
DD4R, and IDD7, are defined with the outputs disabled.
2) The other rank is in IDD2P Precharge Power-Down Current mode
3) Both ranks are in the same IDD current mode
4) Fast: MRS(12)=0
5) Slow: MRS(12)=1
6)
IDD5D and IDD6 values are for 0°C ≤ TCase ≤ 85°C
Rev. 1.1, 2007-01
31
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
TABLE 24
DD Specification for HYS64T[32/64/128]xxxEDL–3–B2
I
Product Type
Unit
Note1)
Organization
256 MB
1 Rank
× 64
512 MB
2 Ranks
× 64
1 GB
2 Ranks
× 64
–3
–3
–3
Symbol
Max.
Max.
Max.
2)
IDD0
380
420
180
36
416
456
360
72
672
792
720
144
640
800
528
208
1112
1112
1192
176
80
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
2)
IDD1
3)
IDD2N
3)
IDD2P
3)
IDD2Q
IDD3N
160
200
132
52
320
400
264
104
656
716
596
88
3)
3)4)
3)5)
2)
IDD3P_0 (fast)
IDD3P_1 (slow)
IDD4R
620
680
560
44
2)
IDD4W
IDD5B
2)
3)6)
3)6)
2)
IDD5D
IDD6
24
40
IDD7
1008
1044
1352
1) Calculated values from component data. ODT disabled. IDD1,
I
DD4R, and IDD7, are defined with the outputs disabled.
2) The other rank is in IDD2P Precharge Power-Down Current mode
3) Both ranks are in the same IDD current mode
4) Fast: MRS(12)=0
5) Slow: MRS(12)=1
6)
IDD5D and IDD6 values are for 0°C ≤ TCase ≤ 85°C
Rev. 1.1, 2007-01
32
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
TABLE 25
DD Specification for HYS64T[32/64/128]xxxEDL–3S–B2
I
Product Type
Unit
Note1)
Organization
256 MB
1 Rank
× 64
512 MB
1 GB
2 Ranks
× 64
2 Ranks
× 64
–3S
–3S
–3S
Symbol
Max.
Max.
Max.
2)
IDD0
360
400
180
36
396
436
360
72
640
752
720
144
640
800
528
208
1112
1112
1192
176
80
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
2)
IDD1
3)
IDD2N
3)
IDD2P
3)
IDD2Q
IDD3N
160
200
132
52
320
400
264
104
656
716
596
88
3)
4)3)
5)3)
2)
IDD3P_0 (fast)
IDD3P_1 (slow)
IDD4R
620
680
560
44
2)
IDD4W
IDD5B
2)
3)6)
3)6)
2)
IDD5D
IDD6
24
40
IDD7
960
996
1288
1) Calculated values from component data. ODT disabled. IDD1,
I
DD4R, and IDD7, are defined with the outputs disabled.
2) The other rank is in IDD2P Precharge Power-Down Current mode
3) Both ranks are in the same IDD current mode
4) Fast: MRS(12)=0
5) Slow: MRS(12)=1
6)
IDD5D and IDD6 values are for 0°C ≤ TCase ≤ 85°C
Rev. 1.1, 2007-01
33
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
TABLE 26
DD Specification for HYS64T[32/64/128]xxxEDL–3.7–B2
I
Product Type
Unit
Note1)
Organization
256 MB
1 Rank
× 64
512 MB
2 Ranks
× 64
1 GB
2 Ranks
× 64
–3.7
–3.7
–3.7
Symbol
Max.
Max.
Max.
2)
IDD0
320
360
152
36
356
396
304
72
592
672
608
144
560
688
448
208
952
952
1112
176
80
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
2)
IDD1
3)
IDD2N
3)
IDD2P
3)
IDD2Q
IDD3N
140
172
112
52
280
344
224
104
556
616
556
88
3)
4)3)
5)3)
2)
IDD3P_0 (fast)
IDD3P_1 (slow)
IDD4R
520
580
520
44
2)
IDD4W
IDD5B
2)
3)6)
3)6)
2)
IDD5D
IDD6
24
40
IDD7
920
956
1232
1) Calculated values from component data. ODT disabled. IDD1,
I
DD4R, and IDD7, are defined with the outputs disabled.
2) The other rank is in IDD2P Precharge Power-Down Current mode
3) Both ranks are in the same IDD current mode
4) Fast: MRS(12)=0
5) Slow: MRS(12)=1
6)
IDD5D and IDD6 values are for 0°C ≤ TCase ≤ 85°C
Rev. 1.1, 2007-01
34
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
4
SPD Codes
This chapter lists all hexadecimal byte values stored in the EEPROM of the products described in this data sheet. SPD stands
for serial presence detect. All values with XX in the table are module specific bytes which are defined during production.
List of SPD Code Tables
•
•
•
•
•
•
•
•
•
•
Table 27 “HYS64T[32/64]xx0EDL-25F-B2” on Page 35
Table 28 “HYS64T128x21EDL-25FB2” on Page 40
Table 29 “HYS64T[32/64]xx0EDL-2.5-B2” on Page 44
Table 30 “HYS64T128x21EDL-2.5B2” on Page 49
Table 31 “HYS64T[32/64]xx0EDL-3-B2” on Page 53
Table 32 “HYS64T128x21EDL-3-B2” on Page 58
Table 33 “HYS64T[32/64]xx0EDL-3S-B2” on Page 62
Table 34 “HYS64T128x21EDL-3S-B2” on Page 67
Table 35 “HYS64T[32/64]xx0EDL-3.7-B2” on Page 71
Table 36 “HYS64T128x21EDL-3.7B2” on Page 76
TABLE 27
HYS64T[32/64]xx0EDL-25F-B2
Product Type
Organization
256MB
256MB
512MB
512MB
×64
×64
×64
×64
1 Rank (×16) 1 Rank (×16) 2 Ranks
(×16)
2 Ranks
(×16)
Label Code
PC2–
PC2–
PC2–
PC2–
6400S–555 6400S–555 6400S–555 6400S–555
JEDEC SPD Revision
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Byte#
Description
0
1
2
3
4
5
Programmed SPD Bytes in EEPROM
Total number of Bytes in EEPROM
Memory Type (DDR2)
80
08
08
0D
0A
60
80
08
08
0D
0A
60
80
08
08
0D
0A
61
80
08
08
0D
0A
61
Number of Row Addresses
Number of Column Addresses
DIMM Rank and Stacking Information
Rev. 1.1, 2007-01
35
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
256MB
256MB
512MB
512MB
×64
×64
×64
×64
1 Rank (×16) 1 Rank (×16) 2 Ranks
(×16)
2 Ranks
(×16)
Label Code
PC2–
PC2–
PC2–
PC2–
6400S–555 6400S–555 6400S–555 6400S–555
JEDEC SPD Revision
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Byte#
Description
6
Data Width
40
00
05
25
40
00
82
10
00
00
0C
04
70
01
04
00
07
25
40
3D
50
32
28
32
40
00
05
25
40
00
82
10
00
00
0C
04
70
01
04
00
07
25
40
3D
50
32
28
32
40
00
05
25
40
00
82
10
00
00
0C
04
70
01
04
00
07
25
40
3D
50
32
28
32
40
00
05
25
40
00
82
10
00
00
0C
04
70
01
04
00
07
25
40
3D
50
32
28
32
7
Not used
8
Interface Voltage Level
9
t
t
CK @ CLMAX (Byte 18) [ns]
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
AC SDRAM @ CLMAX (Byte 18) [ns]
Error Correction Support (non-ECC, ECC)
Refresh Rate and Type
Primary SDRAM Width
Error Checking SDRAM Width
Not used
Burst Length Supported
Number of Banks on SDRAM Device
Supported CAS Latencies
DIMM Mechanical Characteristics
DIMM Type Information
DIMM Attributes
Component Attributes
t
t
t
t
t
t
t
CK @ CLMAX -1 (Byte 18) [ns]
AC SDRAM @ CLMAX -1 [ns]
CK @ CLMAX -2 (Byte 18) [ns]
AC SDRAM @ CLMAX -2 [ns]
RP.MIN [ns]
RRD.MIN [ns]
RCD.MIN [ns]
Rev. 1.1, 2007-01
36
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
256MB
256MB
512MB
512MB
×64
×64
×64
×64
1 Rank (×16) 1 Rank (×16) 2 Ranks
(×16)
2 Ranks
(×16)
Label Code
PC2–
PC2–
PC2–
PC2–
6400S–555 6400S–555 6400S–555 6400S–555
JEDEC SPD Revision
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Byte#
Description
RAS.MIN [ns]
Module Density per Rank
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
t
2D
40
17
25
05
12
3C
1E
1E
00
30
39
69
80
14
1E
00
56
7A
7F
3B
36
2E
5A
2D
40
17
25
05
12
3C
1E
1E
00
30
39
69
80
14
1E
00
56
7A
7F
3B
36
2E
5A
2D
40
17
25
05
12
3C
1E
1E
00
30
39
69
80
14
1E
00
56
7A
7F
3B
36
2E
5A
2D
40
17
25
05
12
3C
1E
1E
00
30
39
69
80
14
1E
00
56
7A
7F
3B
36
2E
5A
t
t
t
t
t
t
t
AS.MIN and tCS.MIN [ns]
AH.MIN and tCH.MIN [ns]
DS.MIN [ns]
DH.MIN [ns]
WR.MIN [ns]
WTR.MIN [ns]
RTP.MIN [ns]
Analysis Characteristics
t
t
t
t
t
t
RC and tRFC Extension
RC.MIN [ns]
RFC.MIN [ns]
CK.MAX [ns]
DQSQ.MAX [ns]
QHS.MAX [ns]
PLL Relock Time
CASE.MAX Delta / ∆T4R4W Delta
T
Psi(T-A) DRAM
∆T0 (DT0)
∆T2N (DT2N, UDIMM) or ∆T2Q (DT2Q, RDIMM)
∆T2P (DT2P)
∆T3N (DT3N)
∆T3P.fast (DT3P fast)
Rev. 1.1, 2007-01
37
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
256MB
256MB
512MB
512MB
×64
×64
×64
×64
1 Rank (×16) 1 Rank (×16) 2 Ranks
(×16)
2 Ranks
(×16)
Label Code
PC2–
PC2–
PC2–
PC2–
6400S–555 6400S–555 6400S–555 6400S–555
JEDEC SPD Revision
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Byte#
Description
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
∆T3P.slow (DT3P slow)
2A
68
22
3D
00
00
00
00
12
54
7F
7F
7F
7F
7F
51
00
00
xx
2A
68
22
3D
00
00
00
00
12
54
7F
7F
7F
7F
7F
51
00
00
xx
2A
68
22
3D
00
00
00
00
12
55
7F
7F
7F
7F
7F
51
00
00
xx
2A
68
22
3D
00
00
00
00
12
55
7F
7F
7F
7F
7F
51
00
00
xx
∆T4R (DT4R) / ∆T4R4W Sign (DT4R4W)
∆T5B (DT5B)
∆T7 (DT7)
Psi(ca) PLL
Psi(ca) REG
∆TPLL (DTPLL)
∆TREG (DTREG) / Toggle Rate
SPD Revision
Checksum of Bytes 0-62
Manufacturer’s JEDEC ID Code (1)
Manufacturer’s JEDEC ID Code (2)
Manufacturer’s JEDEC ID Code (3)
Manufacturer’s JEDEC ID Code (4)
Manufacturer’s JEDEC ID Code (5)
Manufacturer’s JEDEC ID Code (6)
Manufacturer’s JEDEC ID Code (7)
Manufacturer’s JEDEC ID Code (8)
Module Manufacturer Location
Product Type, Char 1
36
34
54
33
32
36
34
54
33
32
36
34
54
36
34
36
34
54
36
34
Product Type, Char 2
Product Type, Char 3
Product Type, Char 4
Product Type, Char 5
Rev. 1.1, 2007-01
38
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
256MB
256MB
512MB
512MB
×64
×64
×64
×64
1 Rank (×16) 1 Rank (×16) 2 Ranks
(×16)
2 Ranks
(×16)
Label Code
PC2–
PC2–
PC2–
PC2–
6400S–555 6400S–555 6400S–555 6400S–555
JEDEC SPD Revision
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Byte#
Description
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
Product Type, Char 6
30
30
30
45
44
4C
32
35
46
42
32
20
20
3x
xx
xx
39
30
30
45
44
4C
32
35
46
42
32
20
20
0x
xx
xx
30
32
30
45
44
4C
32
35
46
42
32
20
20
3x
xx
39
32
30
45
44
4C
32
35
46
42
32
20
20
0x
xx
Product Type, Char 7
Product Type, Char 8
Product Type, Char 9
Product Type, Char 10
Product Type, Char 11
Product Type, Char 12
Product Type, Char 13
Product Type, Char 14
Product Type, Char 15
Product Type, Char 16
Product Type, Char 17
Product Type, Char 18
Module Revision Code
Test Program Revision Code
Module Manufacturing Date Year
Module Manufacturing Date Week
xx
xx
xx
xx
xx
xx
95 - 98 Module Serial Number
99 - 127 Not used
xx
xx
xx
xx
00
FF
00
FF
00
FF
00
FF
128 -
255
Blank for customer use
Rev. 1.1, 2007-01
39
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
TABLE 28
HYS64T128x21EDL-25FB2
Product Type
Organization
HYS64T128021EDL–
25FB2
HYS64T128921EDL–
25FB2
1 GByte
×64
1 GByte
×64
2 Ranks (×8)
PC2–6400S–555
Rev. 1.2
HEX
2 Ranks (×8)
PC2–6400S–555
Rev. 1.2
HEX
Label Code
JEDEC SPD Revision
Byte#
Description
0
Programmed SPD Bytes in EEPROM
Total number of Bytes in EEPROM
Memory Type (DDR2)
80
08
08
0E
0A
61
40
00
05
25
40
00
82
08
00
00
0C
04
70
01
04
00
07
25
40
3D
50
32
1E
80
08
08
0E
0A
61
40
00
05
25
40
00
82
08
00
00
0C
04
70
01
04
00
07
25
40
3D
50
32
1E
1
2
3
Number of Row Addresses
Number of Column Addresses
DIMM Rank and Stacking Information
Data Width
4
5
6
7
Not used
8
Interface Voltage Level
9
t
t
CK @ CLMAX (Byte 18) [ns]
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
AC SDRAM @ CLMAX (Byte 18) [ns]
Error Correction Support (non-ECC, ECC)
Refresh Rate and Type
Primary SDRAM Width
Error Checking SDRAM Width
Not used
Burst Length Supported
Number of Banks on SDRAM Device
Supported CAS Latencies
DIMM Mechanical Characteristics
DIMM Type Information
DIMM Attributes
Component Attributes
t
t
t
t
t
t
CK @ CLMAX -1 (Byte 18) [ns]
AC SDRAM @ CLMAX -1 [ns]
CK @ CLMAX -2 (Byte 18) [ns]
AC SDRAM @ CLMAX -2 [ns]
RP.MIN [ns]
RRD.MIN [ns]
Rev. 1.1, 2007-01
40
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
HYS64T128021EDL–
25FB2
HYS64T128921EDL–
25FB2
1 GByte
×64
1 GByte
×64
2 Ranks (×8)
PC2–6400S–555
Rev. 1.2
HEX
2 Ranks (×8)
PC2–6400S–555
Rev. 1.2
HEX
Label Code
JEDEC SPD Revision
Byte#
Description
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
t
t
RCD.MIN [ns]
RAS.MIN [ns]
32
2D
80
17
25
05
12
3C
1E
1E
00
30
39
69
80
14
1E
00
50
7A
5F
3B
36
2E
5A
2A
5A
22
27
00
00
00
32
2D
80
17
25
05
12
3C
1E
1E
00
30
39
69
80
14
1E
00
50
7A
5F
3B
36
2E
5A
2A
5A
22
27
00
00
00
Module Density per Rank
t
t
t
t
t
t
t
AS.MIN and tCS.MIN [ns]
AH.MIN and tCH.MIN [ns]
DS.MIN [ns]
DH.MIN [ns]
WR.MIN [ns]
WTR.MIN [ns]
RTP.MIN [ns]
Analysis Characteristics
t
t
t
t
t
t
RC and tRFC Extension
RC.MIN [ns]
RFC.MIN [ns]
CK.MAX [ns]
DQSQ.MAX [ns]
QHS.MAX [ns]
PLL Relock Time
CASE.MAX Delta / ∆T4R4W Delta
T
Psi(T-A) DRAM
∆T0 (DT0)
∆T2N (DT2N, UDIMM) or ∆T2Q (DT2Q, RDIMM)
∆T2P (DT2P)
∆T3N (DT3N)
∆T3P.fast (DT3P fast)
∆T3P.slow (DT3P slow)
∆T4R (DT4R) / ∆T4R4W Sign (DT4R4W)
∆T5B (DT5B)
∆T7 (DT7)
Psi(ca) PLL
Psi(ca) REG
∆TPLL (DTPLL)
Rev. 1.1, 2007-01
41
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
HYS64T128021EDL–
25FB2
HYS64T128921EDL–
25FB2
1 GByte
×64
1 GByte
×64
2 Ranks (×8)
PC2–6400S–555
Rev. 1.2
HEX
2 Ranks (×8)
PC2–6400S–555
Rev. 1.2
HEX
Label Code
JEDEC SPD Revision
Byte#
Description
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
∆TREG (DTREG) / Toggle Rate
SPD Revision
00
12
3A
7F
7F
7F
7F
7F
51
00
00
xx
00
12
3A
7F
7F
7F
7F
7F
51
00
00
xx
Checksum of Bytes 0-62
Manufacturer’s JEDEC ID Code (1)
Manufacturer’s JEDEC ID Code (2)
Manufacturer’s JEDEC ID Code (3)
Manufacturer’s JEDEC ID Code (4)
Manufacturer’s JEDEC ID Code (5)
Manufacturer’s JEDEC ID Code (6)
Manufacturer’s JEDEC ID Code (7)
Manufacturer’s JEDEC ID Code (8)
Module Manufacturer Location
Product Type, Char 1
36
34
54
31
32
38
30
32
31
45
44
4C
32
35
46
42
32
20
3x
xx
36
34
54
31
32
38
39
32
31
45
44
4C
32
35
46
42
32
20
0x
xx
Product Type, Char 2
Product Type, Char 3
Product Type, Char 4
Product Type, Char 5
Product Type, Char 6
Product Type, Char 7
Product Type, Char 8
Product Type, Char 9
Product Type, Char 10
Product Type, Char 11
Product Type, Char 12
Product Type, Char 13
Product Type, Char 14
Product Type, Char 15
Product Type, Char 16
Product Type, Char 17
Product Type, Char 18
Module Revision Code
Test Program Revision Code
Rev. 1.1, 2007-01
42
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
HYS64T128021EDL–
25FB2
HYS64T128921EDL–
25FB2
1 GByte
×64
1 GByte
×64
2 Ranks (×8)
PC2–6400S–555
Rev. 1.2
HEX
2 Ranks (×8)
PC2–6400S–555
Rev. 1.2
HEX
Label Code
JEDEC SPD Revision
Byte#
Description
93
94
Module Manufacturing Date Year
Module Manufacturing Date Week
xx
xx
xx
00
FF
xx
xx
xx
00
FF
95 - 98 Module Serial Number
99 - 127 Not used
128 -
255
Blank for customer use
Rev. 1.1, 2007-01
43
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
TABLE 29
HYS64T[32/64]xx0EDL-2.5-B2
Product Type
Organization
256MB
256MB
512MB
512MB
×64
×64
×64
×64
1 Rank (×16) 1 Rank (×16) 2 Ranks
(×16)
2 Ranks
(×16)
Label Code
PC2–
PC2–
PC2–
PC2–
6400S–666 6400S–666 6400S–666 6400S–666
JEDEC SPD Revision
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Byte#
Description
0
Programmed SPD Bytes in EEPROM
Total number of Bytes in EEPROM
Memory Type (DDR2)
80
08
08
0D
0A
60
40
00
05
25
40
00
82
10
00
00
0C
04
70
01
04
00
80
08
08
0D
0A
60
40
00
05
25
40
00
82
10
00
00
0C
04
70
01
04
00
80
08
08
0D
0A
61
40
00
05
25
40
00
82
10
00
00
0C
04
70
01
04
00
80
08
08
0D
0A
61
40
00
05
25
40
00
82
10
00
00
0C
04
70
01
04
00
1
2
3
Number of Row Addresses
Number of Column Addresses
DIMM Rank and Stacking Information
Data Width
4
5
6
7
Not used
8
Interface Voltage Level
9
t
t
CK @ CLMAX (Byte 18) [ns]
10
11
12
13
14
15
16
17
18
19
20
21
AC SDRAM @ CLMAX (Byte 18) [ns]
Error Correction Support (non-ECC, ECC)
Refresh Rate and Type
Primary SDRAM Width
Error Checking SDRAM Width
Not used
Burst Length Supported
Number of Banks on SDRAM Device
Supported CAS Latencies
DIMM Mechanical Characteristics
DIMM Type Information
DIMM Attributes
Rev. 1.1, 2007-01
44
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
256MB
256MB
512MB
512MB
×64
×64
×64
×64
1 Rank (×16) 1 Rank (×16) 2 Ranks
(×16)
2 Ranks
(×16)
Label Code
PC2–
PC2–
PC2–
PC2–
6400S–666 6400S–666 6400S–666 6400S–666
JEDEC SPD Revision
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Byte#
Description
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
Component Attributes
07
30
45
3D
50
3C
28
3C
2D
40
17
25
05
12
3C
1E
1E
00
00
3C
69
80
14
1E
07
30
45
3D
50
3C
28
3C
2D
40
17
25
05
12
3C
1E
1E
00
00
3C
69
80
14
1E
07
30
45
3D
50
3C
28
3C
2D
40
17
25
05
12
3C
1E
1E
00
00
3C
69
80
14
1E
07
30
45
3D
50
3C
28
3C
2D
40
17
25
05
12
3C
1E
1E
00
00
3C
69
80
14
1E
t
t
t
t
t
t
t
t
CK @ CLMAX -1 (Byte 18) [ns]
AC SDRAM @ CLMAX -1 [ns]
CK @ CLMAX -2 (Byte 18) [ns]
AC SDRAM @ CLMAX -2 [ns]
RP.MIN [ns]
RRD.MIN [ns]
RCD.MIN [ns]
RAS.MIN [ns]
Module Density per Rank
t
t
t
t
t
t
t
AS.MIN and tCS.MIN [ns]
AH.MIN and tCH.MIN [ns]
DS.MIN [ns]
DH.MIN [ns]
WR.MIN [ns]
WTR.MIN [ns]
RTP.MIN [ns]
Analysis Characteristics
t
t
t
t
t
t
RC and tRFC Extension
RC.MIN [ns]
RFC.MIN [ns]
CK.MAX [ns]
DQSQ.MAX [ns]
QHS.MAX [ns]
Rev. 1.1, 2007-01
45
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
256MB
256MB
512MB
512MB
×64
×64
×64
×64
1 Rank (×16) 1 Rank (×16) 2 Ranks
(×16)
2 Ranks
(×16)
Label Code
PC2–
PC2–
PC2–
PC2–
6400S–666 6400S–666 6400S–666 6400S–666
JEDEC SPD Revision
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Byte#
Description
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
PLL Relock Time
00
56
7A
77
3B
36
2E
5A
2A
68
22
3B
00
00
00
00
12
41
7F
7F
7F
7F
7F
51
00
56
7A
77
3B
36
2E
5A
2A
68
22
3B
00
00
00
00
12
41
7F
7F
7F
7F
7F
51
00
56
7A
77
3B
36
2E
5A
2A
68
22
3B
00
00
00
00
12
42
7F
7F
7F
7F
7F
51
00
56
7A
77
3B
36
2E
5A
2A
68
22
3B
00
00
00
00
12
42
7F
7F
7F
7F
7F
51
TCASE.MAX Delta / ∆T4R4W Delta
Psi(T-A) DRAM
∆T0 (DT0)
∆T2N (DT2N, UDIMM) or ∆T2Q (DT2Q, RDIMM)
∆T2P (DT2P)
∆T3N (DT3N)
∆T3P.fast (DT3P fast)
∆T3P.slow (DT3P slow)
∆T4R (DT4R) / ∆T4R4W Sign (DT4R4W)
∆T5B (DT5B)
∆T7 (DT7)
Psi(ca) PLL
Psi(ca) REG
∆TPLL (DTPLL)
∆TREG (DTREG) / Toggle Rate
SPD Revision
Checksum of Bytes 0-62
Manufacturer’s JEDEC ID Code (1)
Manufacturer’s JEDEC ID Code (2)
Manufacturer’s JEDEC ID Code (3)
Manufacturer’s JEDEC ID Code (4)
Manufacturer’s JEDEC ID Code (5)
Manufacturer’s JEDEC ID Code (6)
Rev. 1.1, 2007-01
46
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
256MB
256MB
512MB
512MB
×64
×64
×64
×64
1 Rank (×16) 1 Rank (×16) 2 Ranks
(×16)
2 Ranks
(×16)
Label Code
PC2–
PC2–
PC2–
PC2–
6400S–666 6400S–666 6400S–666 6400S–666
JEDEC SPD Revision
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Byte#
Description
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
Manufacturer’s JEDEC ID Code (7)
Manufacturer’s JEDEC ID Code (8)
Module Manufacturer Location
Product Type, Char 1
00
00
xx
00
00
xx
00
00
xx
00
00
xx
36
34
54
33
32
30
30
30
45
44
4C
32
2E
35
42
32
20
20
3x
xx
36
34
54
33
32
39
30
30
45
44
4C
32
2E
35
42
32
20
20
0x
xx
36
34
54
36
34
30
32
30
45
44
4C
32
2E
35
42
32
20
20
3x
xx
36
34
54
36
34
39
32
30
45
44
4C
32
2E
35
42
32
20
20
0x
xx
Product Type, Char 2
Product Type, Char 3
Product Type, Char 4
Product Type, Char 5
Product Type, Char 6
Product Type, Char 7
Product Type, Char 8
Product Type, Char 9
Product Type, Char 10
Product Type, Char 11
Product Type, Char 12
Product Type, Char 13
Product Type, Char 14
Product Type, Char 15
Product Type, Char 16
Product Type, Char 17
Product Type, Char 18
Module Revision Code
Test Program Revision Code
Module Manufacturing Date Year
xx
xx
xx
xx
Rev. 1.1, 2007-01
47
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
256MB
256MB
512MB
512MB
×64
×64
×64
×64
1 Rank (×16) 1 Rank (×16) 2 Ranks
(×16)
2 Ranks
(×16)
Label Code
PC2–
PC2–
PC2–
PC2–
6400S–666 6400S–666 6400S–666 6400S–666
JEDEC SPD Revision
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Byte#
Description
94
Module Manufacturing Date Week
xx
xx
00
FF
xx
xx
00
FF
xx
xx
00
FF
xx
xx
00
FF
95 - 98 Module Serial Number
99 - 127 Not used
128 -
255
Blank for customer use
Rev. 1.1, 2007-01
48
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
TABLE 30
HYS64T128x21EDL-2.5B2
Product Type
Organization
HYS64T128021EDL–2.5B2 HYS64T128921EDL–2.5B2
1 GByte
×64
1 GByte
×64
2 Ranks (×8)
PC2–6400S–666
Rev. 1.2
HEX
2 Ranks (×8)
PC2–6400S–666
Rev. 1.2
HEX
Label Code
JEDEC SPD Revision
Byte#
Description
0
Programmed SPD Bytes in EEPROM
Total number of Bytes in EEPROM
Memory Type (DDR2)
80
08
08
0E
0A
61
40
00
05
25
40
00
82
08
00
00
0C
04
70
01
04
00
07
30
45
3D
50
3C
1E
3C
80
08
08
0E
0A
61
40
00
05
25
40
00
82
08
00
00
0C
04
70
01
04
00
07
30
45
3D
50
3C
1E
3C
1
2
3
Number of Row Addresses
Number of Column Addresses
DIMM Rank and Stacking Information
Data Width
4
5
6
7
Not used
8
Interface Voltage Level
9
t
t
CK @ CLMAX (Byte 18) [ns]
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
AC SDRAM @ CLMAX (Byte 18) [ns]
Error Correction Support (non-ECC, ECC)
Refresh Rate and Type
Primary SDRAM Width
Error Checking SDRAM Width
Not used
Burst Length Supported
Number of Banks on SDRAM Device
Supported CAS Latencies
DIMM Mechanical Characteristics
DIMM Type Information
DIMM Attributes
Component Attributes
t
t
t
t
t
t
t
CK @ CLMAX -1 (Byte 18) [ns]
AC SDRAM @ CLMAX -1 [ns]
CK @ CLMAX -2 (Byte 18) [ns]
AC SDRAM @ CLMAX -2 [ns]
RP.MIN [ns]
RRD.MIN [ns]
RCD.MIN [ns]
Rev. 1.1, 2007-01
49
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
HYS64T128021EDL–2.5B2 HYS64T128921EDL–2.5B2
1 GByte
×64
1 GByte
×64
2 Ranks (×8)
PC2–6400S–666
Rev. 1.2
HEX
2 Ranks (×8)
PC2–6400S–666
Rev. 1.2
HEX
Label Code
JEDEC SPD Revision
Byte#
Description
RAS.MIN [ns]
Module Density per Rank
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
t
2D
80
17
25
05
12
3C
1E
1E
00
00
3C
69
80
14
1E
00
50
7A
5B
3B
36
2E
5A
2A
5A
22
25
00
00
00
00
12
2D
80
17
25
05
12
3C
1E
1E
00
00
3C
69
80
14
1E
00
50
7A
5B
3B
36
2E
5A
2A
5A
22
25
00
00
00
00
12
t
t
t
t
t
t
t
AS.MIN and tCS.MIN [ns]
AH.MIN and tCH.MIN [ns]
DS.MIN [ns]
DH.MIN [ns]
WR.MIN [ns]
WTR.MIN [ns]
RTP.MIN [ns]
Analysis Characteristics
t
t
t
t
t
t
RC and tRFC Extension
RC.MIN [ns]
RFC.MIN [ns]
CK.MAX [ns]
DQSQ.MAX [ns]
QHS.MAX [ns]
PLL Relock Time
CASE.MAX Delta / ∆T4R4W Delta
T
Psi(T-A) DRAM
∆T0 (DT0)
∆T2N (DT2N, UDIMM) or ∆T2Q (DT2Q, RDIMM)
∆T2P (DT2P)
∆T3N (DT3N)
∆T3P.fast (DT3P fast)
∆T3P.slow (DT3P slow)
∆T4R (DT4R) / ∆T4R4W Sign (DT4R4W)
∆T5B (DT5B)
∆T7 (DT7)
Psi(ca) PLL
Psi(ca) REG
∆TPLL (DTPLL)
∆TREG (DTREG) / Toggle Rate
SPD Revision
Rev. 1.1, 2007-01
50
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
HYS64T128021EDL–2.5B2 HYS64T128921EDL–2.5B2
1 GByte
×64
1 GByte
×64
2 Ranks (×8)
PC2–6400S–666
Rev. 1.2
HEX
2 Ranks (×8)
PC2–6400S–666
Rev. 1.2
HEX
Label Code
JEDEC SPD Revision
Byte#
Description
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
Checksum of Bytes 0-62
Manufacturer’s JEDEC ID Code (1)
Manufacturer’s JEDEC ID Code (2)
Manufacturer’s JEDEC ID Code (3)
Manufacturer’s JEDEC ID Code (4)
Manufacturer’s JEDEC ID Code (5)
Manufacturer’s JEDEC ID Code (6)
Manufacturer’s JEDEC ID Code (7)
Manufacturer’s JEDEC ID Code (8)
Module Manufacturer Location
Product Type, Char 1
2B
7F
7F
7F
7F
7F
51
00
00
xx
2B
7F
7F
7F
7F
7F
51
00
00
xx
36
34
54
31
32
38
30
32
31
45
44
4C
32
2E
35
42
32
20
3x
xx
36
34
54
31
32
38
39
32
31
45
44
4C
32
2E
35
42
32
20
0x
xx
Product Type, Char 2
Product Type, Char 3
Product Type, Char 4
Product Type, Char 5
Product Type, Char 6
Product Type, Char 7
Product Type, Char 8
Product Type, Char 9
Product Type, Char 10
Product Type, Char 11
Product Type, Char 12
Product Type, Char 13
Product Type, Char 14
Product Type, Char 15
Product Type, Char 16
Product Type, Char 17
Product Type, Char 18
Module Revision Code
Test Program Revision Code
Module Manufacturing Date Year
Module Manufacturing Date Week
xx
xx
xx
xx
95 - 98 Module Serial Number
xx
xx
Rev. 1.1, 2007-01
51
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
HYS64T128021EDL–2.5B2 HYS64T128921EDL–2.5B2
1 GByte
×64
1 GByte
×64
2 Ranks (×8)
PC2–6400S–666
Rev. 1.2
HEX
2 Ranks (×8)
PC2–6400S–666
Rev. 1.2
HEX
Label Code
JEDEC SPD Revision
Byte#
Description
99 - 127 Not used
00
00
FF
128 -
255
Blank for customer use
FF
Rev. 1.1, 2007-01
52
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
TABLE 31
HYS64T[32/64]xx0EDL-3-B2
Product Type
Organization
256MB
256MB
512MB
512MB
×64
×64
×64
×64
1 Rank (×16) 1 Rank (×16) 2 Ranks
(×16)
2 Ranks
(×16)
Label Code
PC2–
PC2–
PC2–
PC2–
5300S–444 5300S–444 5300S–444 5300S–444
JEDEC SPD Revision
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Byte#
Description
0
Programmed SPD Bytes in EEPROM
Total number of Bytes in EEPROM
Memory Type (DDR2)
80
08
08
0D
0A
60
40
00
05
30
45
00
82
10
00
00
0C
04
38
01
04
00
80
08
08
0D
0A
60
40
00
05
30
45
00
82
10
00
00
0C
04
38
01
04
00
80
08
08
0D
0A
61
40
00
05
30
45
00
82
10
00
00
0C
04
38
01
04
00
80
08
08
0D
0A
61
40
00
05
30
45
00
82
10
00
00
0C
04
38
01
04
00
1
2
3
Number of Row Addresses
Number of Column Addresses
DIMM Rank and Stacking Information
Data Width
4
5
6
7
Not used
8
Interface Voltage Level
9
t
t
CK @ CLMAX (Byte 18) [ns]
10
11
12
13
14
15
16
17
18
19
20
21
AC SDRAM @ CLMAX (Byte 18) [ns]
Error Correction Support (non-ECC, ECC)
Refresh Rate and Type
Primary SDRAM Width
Error Checking SDRAM Width
Not used
Burst Length Supported
Number of Banks on SDRAM Device
Supported CAS Latencies
DIMM Mechanical Characteristics
DIMM Type Information
DIMM Attributes
Rev. 1.1, 2007-01
53
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
256MB
256MB
512MB
512MB
×64
×64
×64
×64
1 Rank (×16) 1 Rank (×16) 2 Ranks
(×16)
2 Ranks
(×16)
Label Code
PC2–
PC2–
PC2–
PC2–
5300S–444 5300S–444 5300S–444 5300S–444
JEDEC SPD Revision
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Byte#
Description
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
Component Attributes
07
30
45
50
60
30
28
30
2D
40
20
27
10
17
3C
1E
1E
00
00
39
69
80
18
22
00
07
30
45
50
60
30
28
30
2D
40
20
27
10
17
3C
1E
1E
00
00
39
69
80
18
22
00
07
30
45
50
60
30
28
30
2D
40
20
27
10
17
3C
1E
1E
00
00
39
69
80
18
22
00
07
30
45
50
60
30
28
30
2D
40
20
27
10
17
3C
1E
1E
00
00
39
69
80
18
22
00
t
t
t
t
t
t
t
t
CK @ CLMAX -1 (Byte 18) [ns]
AC SDRAM @ CLMAX -1 [ns]
CK @ CLMAX -2 (Byte 18) [ns]
AC SDRAM @ CLMAX -2 [ns]
RP.MIN [ns]
RRD.MIN [ns]
RCD.MIN [ns]
RAS.MIN [ns]
Module Density per Rank
t
t
t
t
t
t
t
AS.MIN and tCS.MIN [ns]
AH.MIN and tCH.MIN [ns]
DS.MIN [ns]
DH.MIN [ns]
WR.MIN [ns]
WTR.MIN [ns]
RTP.MIN [ns]
Analysis Characteristics
t
t
t
t
t
t
RC and tRFC Extension
RC.MIN [ns]
RFC.MIN [ns]
CK.MAX [ns]
DQSQ.MAX [ns]
QHS.MAX [ns]
PLL Relock Time
Rev. 1.1, 2007-01
54
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
256MB
256MB
512MB
512MB
×64
×64
×64
×64
1 Rank (×16) 1 Rank (×16) 2 Ranks
(×16)
2 Ranks
(×16)
Label Code
PC2–
PC2–
PC2–
PC2–
5300S–444 5300S–444 5300S–444 5300S–444
JEDEC SPD Revision
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Byte#
Description
CASE.MAX Delta / ∆T4R4W Delta
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
T
54
7A
6F
34
36
27
4C
2A
5A
20
3A
00
00
00
00
12
0D
7F
7F
7F
7F
7F
51
00
00
54
7A
6F
34
36
27
4C
2A
5A
20
3A
00
00
00
00
12
0D
7F
7F
7F
7F
7F
51
00
00
54
7A
6F
34
36
27
4C
2A
5A
20
3A
00
00
00
00
12
0E
7F
7F
7F
7F
7F
51
00
00
54
7A
6F
34
36
27
4C
2A
5A
20
3A
00
00
00
00
12
0E
7F
7F
7F
7F
7F
51
00
00
Psi(T-A) DRAM
∆T0 (DT0)
∆T2N (DT2N, UDIMM) or ∆T2Q (DT2Q, RDIMM)
∆T2P (DT2P)
∆T3N (DT3N)
∆T3P.fast (DT3P fast)
∆T3P.slow (DT3P slow)
∆T4R (DT4R) / ∆T4R4W Sign (DT4R4W)
∆T5B (DT5B)
∆T7 (DT7)
Psi(ca) PLL
Psi(ca) REG
∆TPLL (DTPLL)
∆TREG (DTREG) / Toggle Rate
SPD Revision
Checksum of Bytes 0-62
Manufacturer’s JEDEC ID Code (1)
Manufacturer’s JEDEC ID Code (2)
Manufacturer’s JEDEC ID Code (3)
Manufacturer’s JEDEC ID Code (4)
Manufacturer’s JEDEC ID Code (5)
Manufacturer’s JEDEC ID Code (6)
Manufacturer’s JEDEC ID Code (7)
Manufacturer’s JEDEC ID Code (8)
Rev. 1.1, 2007-01
55
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
256MB
256MB
512MB
512MB
×64
×64
×64
×64
1 Rank (×16) 1 Rank (×16) 2 Ranks
(×16)
2 Ranks
(×16)
Label Code
PC2–
PC2–
PC2–
PC2–
5300S–444 5300S–444 5300S–444 5300S–444
JEDEC SPD Revision
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Byte#
Description
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
Module Manufacturer Location
Product Type, Char 1
xx
36
34
54
33
32
30
30
30
45
44
4C
33
42
32
20
20
20
20
2x
xx
xx
xx
xx
xx
36
34
54
33
32
39
30
30
45
44
4C
33
42
32
20
20
20
20
0x
xx
xx
xx
xx
xx
36
34
54
36
34
30
32
30
45
44
4C
33
42
32
20
20
20
20
2x
xx
xx
xx
xx
xx
36
34
54
36
34
39
32
30
45
44
4C
33
42
32
20
20
20
20
0x
xx
xx
xx
xx
Product Type, Char 2
Product Type, Char 3
Product Type, Char 4
Product Type, Char 5
Product Type, Char 6
Product Type, Char 7
Product Type, Char 8
Product Type, Char 9
Product Type, Char 10
Product Type, Char 11
Product Type, Char 12
Product Type, Char 13
Product Type, Char 14
Product Type, Char 15
Product Type, Char 16
Product Type, Char 17
Product Type, Char 18
Module Revision Code
Test Program Revision Code
Module Manufacturing Date Year
Module Manufacturing Date Week
95 - 98 Module Serial Number
Rev. 1.1, 2007-01
56
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
256MB
256MB
512MB
512MB
×64
×64
×64
×64
1 Rank (×16) 1 Rank (×16) 2 Ranks
(×16)
2 Ranks
(×16)
Label Code
PC2–
PC2–
PC2–
PC2–
5300S–444 5300S–444 5300S–444 5300S–444
JEDEC SPD Revision
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Byte#
Description
99 - 127 Not used
00
00
00
FF
00
FF
128 -
255
Blank for customer use
FF
FF
Rev. 1.1, 2007-01
57
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
TABLE 32
HYS64T128x21EDL-3-B2
Product Type
Organization
HYS64T128021EDL–3–B2 HYS64T128921EDL–3–B2
1 GByte
×64
1 GByte
×64
2 Ranks (×8)
PC2–5300S–444
Rev. 1.2
HEX
2 Ranks (×8)
PC2–5300S–444
Rev. 1.2
HEX
Label Code
JEDEC SPD Revision
Byte#
Description
0
Programmed SPD Bytes in EEPROM
Total number of Bytes in EEPROM
Memory Type (DDR2)
80
08
08
0E
0A
61
40
00
05
30
45
00
82
08
00
00
0C
04
38
01
04
00
07
30
45
50
60
30
1E
30
80
08
08
0E
0A
61
40
00
05
30
45
00
82
08
00
00
0C
04
38
01
04
00
07
30
45
50
60
30
1E
30
1
2
3
Number of Row Addresses
Number of Column Addresses
DIMM Rank and Stacking Information
Data Width
4
5
6
7
Not used
8
Interface Voltage Level
9
t
t
CK @ CLMAX (Byte 18) [ns]
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
AC SDRAM @ CLMAX (Byte 18) [ns]
Error Correction Support (non-ECC, ECC)
Refresh Rate and Type
Primary SDRAM Width
Error Checking SDRAM Width
Not used
Burst Length Supported
Number of Banks on SDRAM Device
Supported CAS Latencies
DIMM Mechanical Characteristics
DIMM Type Information
DIMM Attributes
Component Attributes
t
t
t
t
t
t
t
CK @ CLMAX -1 (Byte 18) [ns]
AC SDRAM @ CLMAX -1 [ns]
CK @ CLMAX -2 (Byte 18) [ns]
AC SDRAM @ CLMAX -2 [ns]
RP.MIN [ns]
RRD.MIN [ns]
RCD.MIN [ns]
Rev. 1.1, 2007-01
58
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
HYS64T128021EDL–3–B2 HYS64T128921EDL–3–B2
1 GByte
×64
1 GByte
×64
2 Ranks (×8)
PC2–5300S–444
Rev. 1.2
HEX
2 Ranks (×8)
PC2–5300S–444
Rev. 1.2
HEX
Label Code
JEDEC SPD Revision
Byte#
Description
RAS.MIN [ns]
Module Density per Rank
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
t
2D
80
20
27
10
17
3C
1E
1E
00
00
39
69
80
18
22
00
50
7A
53
34
36
27
4C
2A
4C
20
25
00
00
00
00
12
2D
80
20
27
10
17
3C
1E
1E
00
00
39
69
80
18
22
00
50
7A
53
34
36
27
4C
2A
4C
20
25
00
00
00
00
12
t
t
t
t
t
t
t
AS.MIN and tCS.MIN [ns]
AH.MIN and tCH.MIN [ns]
DS.MIN [ns]
DH.MIN [ns]
WR.MIN [ns]
WTR.MIN [ns]
RTP.MIN [ns]
Analysis Characteristics
t
t
t
t
t
t
RC and tRFC Extension
RC.MIN [ns]
RFC.MIN [ns]
CK.MAX [ns]
DQSQ.MAX [ns]
QHS.MAX [ns]
PLL Relock Time
CASE.MAX Delta / ∆T4R4W Delta
T
Psi(T-A) DRAM
∆T0 (DT0)
∆T2N (DT2N, UDIMM) or ∆T2Q (DT2Q, RDIMM)
∆T2P (DT2P)
∆T3N (DT3N)
∆T3P.fast (DT3P fast)
∆T3P.slow (DT3P slow)
∆T4R (DT4R) / ∆T4R4W Sign (DT4R4W)
∆T5B (DT5B)
∆T7 (DT7)
Psi(ca) PLL
Psi(ca) REG
∆TPLL (DTPLL)
∆TREG (DTREG) / Toggle Rate
SPD Revision
Rev. 1.1, 2007-01
59
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
HYS64T128021EDL–3–B2 HYS64T128921EDL–3–B2
1 GByte
×64
1 GByte
×64
2 Ranks (×8)
PC2–5300S–444
Rev. 1.2
HEX
2 Ranks (×8)
PC2–5300S–444
Rev. 1.2
HEX
Label Code
JEDEC SPD Revision
Byte#
Description
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
Checksum of Bytes 0-62
Manufacturer’s JEDEC ID Code (1)
Manufacturer’s JEDEC ID Code (2)
Manufacturer’s JEDEC ID Code (3)
Manufacturer’s JEDEC ID Code (4)
Manufacturer’s JEDEC ID Code (5)
Manufacturer’s JEDEC ID Code (6)
Manufacturer’s JEDEC ID Code (7)
Manufacturer’s JEDEC ID Code (8)
Module Manufacturer Location
Product Type, Char 1
FA
7F
7F
7F
7F
7F
51
00
00
xx
FA
7F
7F
7F
7F
7F
51
00
00
xx
36
34
54
31
32
38
30
32
31
45
44
4C
33
42
32
20
20
20
2x
xx
36
34
54
31
32
38
39
32
31
45
44
4C
33
42
32
20
20
20
0x
xx
Product Type, Char 2
Product Type, Char 3
Product Type, Char 4
Product Type, Char 5
Product Type, Char 6
Product Type, Char 7
Product Type, Char 8
Product Type, Char 9
Product Type, Char 10
Product Type, Char 11
Product Type, Char 12
Product Type, Char 13
Product Type, Char 14
Product Type, Char 15
Product Type, Char 16
Product Type, Char 17
Product Type, Char 18
Module Revision Code
Test Program Revision Code
Module Manufacturing Date Year
Module Manufacturing Date Week
xx
xx
xx
xx
95 - 98 Module Serial Number
xx
xx
Rev. 1.1, 2007-01
60
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
HYS64T128021EDL–3–B2 HYS64T128921EDL–3–B2
1 GByte
×64
1 GByte
×64
2 Ranks (×8)
PC2–5300S–444
Rev. 1.2
HEX
2 Ranks (×8)
PC2–5300S–444
Rev. 1.2
HEX
Label Code
JEDEC SPD Revision
Byte#
Description
99 - 127 Not used
00
00
FF
128 -
255
Blank for customer use
FF
Rev. 1.1, 2007-01
61
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
TABLE 33
HYS64T[32/64]xx0EDL-3S-B2
Product Type
Organization
256MB
256MB
512MB
512MB
×64
×64
×64
×64
1 Rank (×16) 1 Rank (×16) 2 Ranks
(×16)
2 Ranks
(×16)
Label Code
PC2–
PC2–
PC2–
PC2–
5300S–555 5300S–555 5300S–555 5300S–555
JEDEC SPD Revision
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Byte#
Description
0
Programmed SPD Bytes in EEPROM
Total number of Bytes in EEPROM
Memory Type (DDR2)
80
08
08
0D
0A
60
40
00
05
30
45
00
82
10
00
00
0C
04
38
01
04
00
80
08
08
0D
0A
60
40
00
05
30
45
00
82
10
00
00
0C
04
38
01
04
00
80
08
08
0D
0A
61
40
00
05
30
45
00
82
10
00
00
0C
04
38
01
04
00
80
08
08
0D
0A
61
40
00
05
30
45
00
82
10
00
00
0C
04
38
01
04
00
1
2
3
Number of Row Addresses
Number of Column Addresses
DIMM Rank and Stacking Information
Data Width
4
5
6
7
Not used
8
Interface Voltage Level
9
t
t
CK @ CLMAX (Byte 18) [ns]
10
11
12
13
14
15
16
17
18
19
20
21
AC SDRAM @ CLMAX (Byte 18) [ns]
Error Correction Support (non-ECC, ECC)
Refresh Rate and Type
Primary SDRAM Width
Error Checking SDRAM Width
Not used
Burst Length Supported
Number of Banks on SDRAM Device
Supported CAS Latencies
DIMM Mechanical Characteristics
DIMM Type Information
DIMM Attributes
Rev. 1.1, 2007-01
62
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
256MB
256MB
512MB
512MB
×64
×64
×64
×64
1 Rank (×16) 1 Rank (×16) 2 Ranks
(×16)
2 Ranks
(×16)
Label Code
PC2–
PC2–
PC2–
PC2–
5300S–555 5300S–555 5300S–555 5300S–555
JEDEC SPD Revision
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Byte#
Description
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
Component Attributes
07
3D
50
50
60
3C
28
3C
2D
40
20
27
10
17
3C
1E
1E
00
00
3C
69
80
18
22
07
3D
50
50
60
3C
28
3C
2D
40
20
27
10
17
3C
1E
1E
00
00
3C
69
80
18
22
07
3D
50
50
60
3C
28
3C
2D
40
20
27
10
17
3C
1E
1E
00
00
3C
69
80
18
22
07
3D
50
50
60
3C
28
3C
2D
40
20
27
10
17
3C
1E
1E
00
00
3C
69
80
18
22
t
t
t
t
t
t
t
t
CK @ CLMAX -1 (Byte 18) [ns]
AC SDRAM @ CLMAX -1 [ns]
CK @ CLMAX -2 (Byte 18) [ns]
AC SDRAM @ CLMAX -2 [ns]
RP.MIN [ns]
RRD.MIN [ns]
RCD.MIN [ns]
RAS.MIN [ns]
Module Density per Rank
t
t
t
t
t
t
t
AS.MIN and tCS.MIN [ns]
AH.MIN and tCH.MIN [ns]
DS.MIN [ns]
DH.MIN [ns]
WR.MIN [ns]
WTR.MIN [ns]
RTP.MIN [ns]
Analysis Characteristics
t
t
t
t
t
t
RC and tRFC Extension
RC.MIN [ns]
RFC.MIN [ns]
CK.MAX [ns]
DQSQ.MAX [ns]
QHS.MAX [ns]
Rev. 1.1, 2007-01
63
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
256MB
256MB
512MB
512MB
×64
×64
×64
×64
1 Rank (×16) 1 Rank (×16) 2 Ranks
(×16)
2 Ranks
(×16)
Label Code
PC2–
PC2–
PC2–
PC2–
5300S–555 5300S–555 5300S–555 5300S–555
JEDEC SPD Revision
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Byte#
Description
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
PLL Relock Time
00
54
7A
67
34
36
27
4C
2A
5A
20
38
00
00
00
00
12
36
7F
7F
7F
7F
7F
51
00
54
7A
67
34
36
27
4C
2A
5A
20
38
00
00
00
00
12
36
7F
7F
7F
7F
7F
51
00
54
7A
67
34
36
27
4C
2A
5A
20
38
00
00
00
00
12
37
7F
7F
7F
7F
7F
51
00
54
7A
67
34
36
27
4C
2A
5A
20
38
00
00
00
00
12
37
7F
7F
7F
7F
7F
51
TCASE.MAX Delta / ∆T4R4W Delta
Psi(T-A) DRAM
∆T0 (DT0)
∆T2N (DT2N, UDIMM) or ∆T2Q (DT2Q, RDIMM)
∆T2P (DT2P)
∆T3N (DT3N)
∆T3P.fast (DT3P fast)
∆T3P.slow (DT3P slow)
∆T4R (DT4R) / ∆T4R4W Sign (DT4R4W)
∆T5B (DT5B)
∆T7 (DT7)
Psi(ca) PLL
Psi(ca) REG
∆TPLL (DTPLL)
∆TREG (DTREG) / Toggle Rate
SPD Revision
Checksum of Bytes 0-62
Manufacturer’s JEDEC ID Code (1)
Manufacturer’s JEDEC ID Code (2)
Manufacturer’s JEDEC ID Code (3)
Manufacturer’s JEDEC ID Code (4)
Manufacturer’s JEDEC ID Code (5)
Manufacturer’s JEDEC ID Code (6)
Rev. 1.1, 2007-01
64
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
256MB
256MB
512MB
512MB
×64
×64
×64
×64
1 Rank (×16) 1 Rank (×16) 2 Ranks
(×16)
2 Ranks
(×16)
Label Code
PC2–
PC2–
PC2–
PC2–
5300S–555 5300S–555 5300S–555 5300S–555
JEDEC SPD Revision
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Byte#
Description
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
Manufacturer’s JEDEC ID Code (7)
Manufacturer’s JEDEC ID Code (8)
Module Manufacturer Location
Product Type, Char 1
00
00
xx
00
00
xx
00
00
xx
00
00
xx
36
34
54
33
32
30
30
30
45
44
4C
33
53
42
32
20
20
20
2x
xx
36
34
54
33
32
39
30
30
45
44
4C
33
53
42
32
20
20
20
0x
xx
36
34
54
36
34
30
32
30
45
44
4C
33
53
42
32
20
20
20
2x
xx
36
34
54
36
34
39
32
30
45
44
4C
33
53
42
32
20
20
20
0x
xx
Product Type, Char 2
Product Type, Char 3
Product Type, Char 4
Product Type, Char 5
Product Type, Char 6
Product Type, Char 7
Product Type, Char 8
Product Type, Char 9
Product Type, Char 10
Product Type, Char 11
Product Type, Char 12
Product Type, Char 13
Product Type, Char 14
Product Type, Char 15
Product Type, Char 16
Product Type, Char 17
Product Type, Char 18
Module Revision Code
Test Program Revision Code
Module Manufacturing Date Year
xx
xx
xx
xx
Rev. 1.1, 2007-01
65
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
256MB
256MB
512MB
512MB
×64
×64
×64
×64
1 Rank (×16) 1 Rank (×16) 2 Ranks
(×16)
2 Ranks
(×16)
Label Code
PC2–
PC2–
PC2–
PC2–
5300S–555 5300S–555 5300S–555 5300S–555
JEDEC SPD Revision
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Byte#
Description
94
Module Manufacturing Date Week
xx
xx
00
FF
xx
xx
00
FF
xx
xx
00
FF
xx
xx
00
FF
95 - 98 Module Serial Number
99 - 127 Not used
128 -
255
Blank for customer use
Rev. 1.1, 2007-01
66
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
TABLE 34
HYS64T128x21EDL-3S-B2
Product Type
Organization
HYS64T128021EDL–3S–
B2
HYS64T128921EDL–3S–
B2
1 GByte
×64
1 GByte
×64
2 Ranks (×8)
PC2–5300S–555
Rev. 1.2
HEX
2 Ranks (×8)
PC2–5300S–555
Rev. 1.2
HEX
Label Code
JEDEC SPD Revision
Byte#
Description
0
Programmed SPD Bytes in EEPROM
Total number of Bytes in EEPROM
Memory Type (DDR2)
80
08
08
0E
0A
61
40
00
05
30
45
00
82
08
00
00
0C
04
38
01
04
00
07
3D
50
50
60
3C
1E
80
08
08
0E
0A
61
40
00
05
30
45
00
82
08
00
00
0C
04
38
01
04
00
07
3D
50
50
60
3C
1E
1
2
3
Number of Row Addresses
Number of Column Addresses
DIMM Rank and Stacking Information
Data Width
4
5
6
7
Not used
8
Interface Voltage Level
9
t
t
CK @ CLMAX (Byte 18) [ns]
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
AC SDRAM @ CLMAX (Byte 18) [ns]
Error Correction Support (non-ECC, ECC)
Refresh Rate and Type
Primary SDRAM Width
Error Checking SDRAM Width
Not used
Burst Length Supported
Number of Banks on SDRAM Device
Supported CAS Latencies
DIMM Mechanical Characteristics
DIMM Type Information
DIMM Attributes
Component Attributes
t
t
t
t
t
t
CK @ CLMAX -1 (Byte 18) [ns]
AC SDRAM @ CLMAX -1 [ns]
CK @ CLMAX -2 (Byte 18) [ns]
AC SDRAM @ CLMAX -2 [ns]
RP.MIN [ns]
RRD.MIN [ns]
Rev. 1.1, 2007-01
67
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
HYS64T128021EDL–3S–
B2
HYS64T128921EDL–3S–
B2
1 GByte
×64
1 GByte
×64
2 Ranks (×8)
PC2–5300S–555
Rev. 1.2
HEX
2 Ranks (×8)
PC2–5300S–555
Rev. 1.2
HEX
Label Code
JEDEC SPD Revision
Byte#
Description
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
t
t
RCD.MIN [ns]
RAS.MIN [ns]
3C
2D
80
20
27
10
17
3C
1E
1E
00
00
3C
69
80
18
22
00
50
7A
4B
34
36
27
4C
2A
4C
20
23
00
00
00
3C
2D
80
20
27
10
17
3C
1E
1E
00
00
3C
69
80
18
22
00
50
7A
4B
34
36
27
4C
2A
4C
20
23
00
00
00
Module Density per Rank
t
t
t
t
t
t
t
AS.MIN and tCS.MIN [ns]
AH.MIN and tCH.MIN [ns]
DS.MIN [ns]
DH.MIN [ns]
WR.MIN [ns]
WTR.MIN [ns]
RTP.MIN [ns]
Analysis Characteristics
t
t
t
t
t
t
RC and tRFC Extension
RC.MIN [ns]
RFC.MIN [ns]
CK.MAX [ns]
DQSQ.MAX [ns]
QHS.MAX [ns]
PLL Relock Time
CASE.MAX Delta / ∆T4R4W Delta
T
Psi(T-A) DRAM
∆T0 (DT0)
∆T2N (DT2N, UDIMM) or ∆T2Q (DT2Q, RDIMM)
∆T2P (DT2P)
∆T3N (DT3N)
∆T3P.fast (DT3P fast)
∆T3P.slow (DT3P slow)
∆T4R (DT4R) / ∆T4R4W Sign (DT4R4W)
∆T5B (DT5B)
∆T7 (DT7)
Psi(ca) PLL
Psi(ca) REG
∆TPLL (DTPLL)
Rev. 1.1, 2007-01
68
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
HYS64T128021EDL–3S–
B2
HYS64T128921EDL–3S–
B2
1 GByte
×64
1 GByte
×64
2 Ranks (×8)
PC2–5300S–555
Rev. 1.2
HEX
2 Ranks (×8)
PC2–5300S–555
Rev. 1.2
HEX
Label Code
JEDEC SPD Revision
Byte#
Description
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
∆TREG (DTREG) / Toggle Rate
SPD Revision
00
12
23
7F
7F
7F
7F
7F
51
00
00
xx
00
12
23
7F
7F
7F
7F
7F
51
00
00
xx
Checksum of Bytes 0-62
Manufacturer’s JEDEC ID Code (1)
Manufacturer’s JEDEC ID Code (2)
Manufacturer’s JEDEC ID Code (3)
Manufacturer’s JEDEC ID Code (4)
Manufacturer’s JEDEC ID Code (5)
Manufacturer’s JEDEC ID Code (6)
Manufacturer’s JEDEC ID Code (7)
Manufacturer’s JEDEC ID Code (8)
Module Manufacturer Location
Product Type, Char 1
36
34
54
31
32
38
30
32
31
45
44
4C
33
53
42
32
20
20
2x
xx
36
34
54
31
32
38
39
32
31
45
44
4C
33
53
42
32
20
20
0x
xx
Product Type, Char 2
Product Type, Char 3
Product Type, Char 4
Product Type, Char 5
Product Type, Char 6
Product Type, Char 7
Product Type, Char 8
Product Type, Char 9
Product Type, Char 10
Product Type, Char 11
Product Type, Char 12
Product Type, Char 13
Product Type, Char 14
Product Type, Char 15
Product Type, Char 16
Product Type, Char 17
Product Type, Char 18
Module Revision Code
Test Program Revision Code
Rev. 1.1, 2007-01
69
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
HYS64T128021EDL–3S–
B2
HYS64T128921EDL–3S–
B2
1 GByte
×64
1 GByte
×64
2 Ranks (×8)
PC2–5300S–555
Rev. 1.2
HEX
2 Ranks (×8)
PC2–5300S–555
Rev. 1.2
HEX
Label Code
JEDEC SPD Revision
Byte#
Description
93
94
Module Manufacturing Date Year
Module Manufacturing Date Week
xx
xx
xx
00
FF
xx
xx
xx
00
FF
95 - 98 Module Serial Number
99 - 127 Not used
128 -
255
Blank for customer use
Rev. 1.1, 2007-01
70
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
TABLE 35
HYS64T[32/64]xx0EDL-3.7-B2
Product Type
Organization
256MB
256MB
512MB
512MB
×64
×64
×64
×64
1 Rank (×16) 1 Rank (×16) 2 Ranks
(×16)
2 Ranks
(×16)
Label Code
PC2–
PC2–
PC2–
PC2–
4200S–444 4200S–444 4200S–444 4200S–444
JEDEC SPD Revision
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Byte#
Description
0
Programmed SPD Bytes in EEPROM
Total number of Bytes in EEPROM
Memory Type (DDR2)
80
08
08
0D
0A
60
40
00
05
3D
50
00
82
10
00
00
0C
04
38
01
04
00
80
08
08
0D
0A
60
40
00
05
3D
50
00
82
10
00
00
0C
04
38
01
04
00
80
08
08
0D
0A
61
40
00
05
3D
50
00
82
10
00
00
0C
04
38
01
04
00
80
08
08
0D
0A
61
40
00
05
3D
50
00
82
10
00
00
0C
04
38
01
04
00
1
2
3
Number of Row Addresses
Number of Column Addresses
DIMM Rank and Stacking Information
Data Width
4
5
6
7
Not used
8
Interface Voltage Level
9
t
t
CK @ CLMAX (Byte 18) [ns]
10
11
12
13
14
15
16
17
18
19
20
21
AC SDRAM @ CLMAX (Byte 18) [ns]
Error Correction Support (non-ECC, ECC)
Refresh Rate and Type
Primary SDRAM Width
Error Checking SDRAM Width
Not used
Burst Length Supported
Number of Banks on SDRAM Device
Supported CAS Latencies
DIMM Mechanical Characteristics
DIMM Type Information
DIMM Attributes
Rev. 1.1, 2007-01
71
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
256MB
256MB
512MB
512MB
×64
×64
×64
×64
1 Rank (×16) 1 Rank (×16) 2 Ranks
(×16)
2 Ranks
(×16)
Label Code
PC2–
PC2–
PC2–
PC2–
4200S–444 4200S–444 4200S–444 4200S–444
JEDEC SPD Revision
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Byte#
Description
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
Component Attributes
07
3D
50
50
60
3C
28
3C
2D
40
25
37
10
22
3C
1E
1E
00
00
3C
69
80
1E
28
07
3D
50
50
60
3C
28
3C
2D
40
25
37
10
22
3C
1E
1E
00
00
3C
69
80
1E
28
07
3D
50
50
60
3C
28
3C
2D
40
25
37
10
22
3C
1E
1E
00
00
3C
69
80
1E
28
07
3D
50
50
60
3C
28
3C
2D
40
25
37
10
22
3C
1E
1E
00
00
3C
69
80
1E
28
t
t
t
t
t
t
t
t
CK @ CLMAX -1 (Byte 18) [ns]
AC SDRAM @ CLMAX -1 [ns]
CK @ CLMAX -2 (Byte 18) [ns]
AC SDRAM @ CLMAX -2 [ns]
RP.MIN [ns]
RRD.MIN [ns]
RCD.MIN [ns]
RAS.MIN [ns]
Module Density per Rank
t
t
t
t
t
t
t
AS.MIN and tCS.MIN [ns]
AH.MIN and tCH.MIN [ns]
DS.MIN [ns]
DH.MIN [ns]
WR.MIN [ns]
WTR.MIN [ns]
RTP.MIN [ns]
Analysis Characteristics
t
t
t
t
t
t
RC and tRFC Extension
RC.MIN [ns]
RFC.MIN [ns]
CK.MAX [ns]
DQSQ.MAX [ns]
QHS.MAX [ns]
Rev. 1.1, 2007-01
72
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
256MB
256MB
512MB
512MB
×64
×64
×64
×64
1 Rank (×16) 1 Rank (×16) 2 Ranks
(×16)
2 Ranks
(×16)
Label Code
PC2–
PC2–
PC2–
PC2–
4200S–444 4200S–444 4200S–444 4200S–444
JEDEC SPD Revision
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Byte#
Description
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
PLL Relock Time
00
54
7A
5B
2C
36
21
41
2A
4C
1E
35
00
00
00
00
12
42
7F
7F
7F
7F
7F
51
00
54
7A
5B
2C
36
21
41
2A
4C
1E
35
00
00
00
00
12
42
7F
7F
7F
7F
7F
51
00
54
7A
5B
2C
36
21
41
2A
4C
1E
35
00
00
00
00
12
43
7F
7F
7F
7F
7F
51
00
54
7A
5B
2C
36
21
41
2A
4C
1E
35
00
00
00
00
12
43
7F
7F
7F
7F
7F
51
TCASE.MAX Delta / ∆T4R4W Delta
Psi(T-A) DRAM
∆T0 (DT0)
∆T2N (DT2N, UDIMM) or ∆T2Q (DT2Q, RDIMM)
∆T2P (DT2P)
∆T3N (DT3N)
∆T3P.fast (DT3P fast)
∆T3P.slow (DT3P slow)
∆T4R (DT4R) / ∆T4R4W Sign (DT4R4W)
∆T5B (DT5B)
∆T7 (DT7)
Psi(ca) PLL
Psi(ca) REG
∆TPLL (DTPLL)
∆TREG (DTREG) / Toggle Rate
SPD Revision
Checksum of Bytes 0-62
Manufacturer’s JEDEC ID Code (1)
Manufacturer’s JEDEC ID Code (2)
Manufacturer’s JEDEC ID Code (3)
Manufacturer’s JEDEC ID Code (4)
Manufacturer’s JEDEC ID Code (5)
Manufacturer’s JEDEC ID Code (6)
Rev. 1.1, 2007-01
73
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
256MB
256MB
512MB
512MB
×64
×64
×64
×64
1 Rank (×16) 1 Rank (×16) 2 Ranks
(×16)
2 Ranks
(×16)
Label Code
PC2–
PC2–
PC2–
PC2–
4200S–444 4200S–444 4200S–444 4200S–444
JEDEC SPD Revision
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Byte#
Description
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
Manufacturer’s JEDEC ID Code (7)
Manufacturer’s JEDEC ID Code (8)
Module Manufacturer Location
Product Type, Char 1
00
00
xx
00
00
xx
00
00
xx
00
00
xx
36
34
54
33
32
30
30
30
45
44
4C
33
2E
37
42
32
20
20
2x
xx
36
34
54
33
32
39
30
30
45
44
4C
33
2E
37
42
32
20
20
0x
xx
36
34
54
36
34
30
32
30
45
44
4C
33
2E
37
42
32
20
20
2x
xx
36
34
54
36
34
39
32
30
45
44
4C
33
2E
37
42
32
20
20
0x
xx
Product Type, Char 2
Product Type, Char 3
Product Type, Char 4
Product Type, Char 5
Product Type, Char 6
Product Type, Char 7
Product Type, Char 8
Product Type, Char 9
Product Type, Char 10
Product Type, Char 11
Product Type, Char 12
Product Type, Char 13
Product Type, Char 14
Product Type, Char 15
Product Type, Char 16
Product Type, Char 17
Product Type, Char 18
Module Revision Code
Test Program Revision Code
Module Manufacturing Date Year
xx
xx
xx
xx
Rev. 1.1, 2007-01
74
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
256MB
256MB
512MB
512MB
×64
×64
×64
×64
1 Rank (×16) 1 Rank (×16) 2 Ranks
(×16)
2 Ranks
(×16)
Label Code
PC2–
PC2–
PC2–
PC2–
4200S–444 4200S–444 4200S–444 4200S–444
JEDEC SPD Revision
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Rev. 1.2
HEX
Byte#
Description
94
Module Manufacturing Date Week
xx
xx
00
FF
xx
xx
00
FF
xx
xx
00
FF
xx
xx
00
FF
95 - 98 Module Serial Number
99 - 127 Not used
128 -
255
Blank for customer use
Rev. 1.1, 2007-01
75
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
TABLE 36
HYS64T128x21EDL-3.7B2
Product Type
Organization
HYS64T128021EDL–3.7B2 HYS64T128921EDL–3.7B2
1 GByte
×64
1 GByte
×64
2 Ranks (×8)
PC2–4200S–444
Rev. 1.2
HEX
2 Ranks (×8)
PC2–4200S–444
Rev. 1.2
HEX
Label Code
JEDEC SPD Revision
Byte#
Description
0
Programmed SPD Bytes in EEPROM
Total number of Bytes in EEPROM
Memory Type (DDR2)
80
08
08
0E
0A
61
40
00
05
3D
50
00
82
08
00
00
0C
04
38
01
04
00
07
3D
50
50
60
3C
1E
3C
80
08
08
0E
0A
61
40
00
05
3D
50
00
82
08
00
00
0C
04
38
01
04
00
07
3D
50
50
60
3C
1E
3C
1
2
3
Number of Row Addresses
Number of Column Addresses
DIMM Rank and Stacking Information
Data Width
4
5
6
7
Not used
8
Interface Voltage Level
9
t
t
CK @ CLMAX (Byte 18) [ns]
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
AC SDRAM @ CLMAX (Byte 18) [ns]
Error Correction Support (non-ECC, ECC)
Refresh Rate and Type
Primary SDRAM Width
Error Checking SDRAM Width
Not used
Burst Length Supported
Number of Banks on SDRAM Device
Supported CAS Latencies
DIMM Mechanical Characteristics
DIMM Type Information
DIMM Attributes
Component Attributes
t
t
t
t
t
t
t
CK @ CLMAX -1 (Byte 18) [ns]
AC SDRAM @ CLMAX -1 [ns]
CK @ CLMAX -2 (Byte 18) [ns]
AC SDRAM @ CLMAX -2 [ns]
RP.MIN [ns]
RRD.MIN [ns]
RCD.MIN [ns]
Rev. 1.1, 2007-01
76
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
HYS64T128021EDL–3.7B2 HYS64T128921EDL–3.7B2
1 GByte
×64
1 GByte
×64
2 Ranks (×8)
PC2–4200S–444
Rev. 1.2
HEX
2 Ranks (×8)
PC2–4200S–444
Rev. 1.2
HEX
Label Code
JEDEC SPD Revision
Byte#
Description
RAS.MIN [ns]
Module Density per Rank
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
t
2D
80
25
37
10
22
3C
1E
1E
00
00
3C
69
80
1E
28
00
50
7A
43
2C
36
21
41
2A
40
1E
22
00
00
00
00
12
2D
80
25
37
10
22
3C
1E
1E
00
00
3C
69
80
1E
28
00
50
7A
43
2C
36
21
41
2A
40
1E
22
00
00
00
00
12
t
t
t
t
t
t
t
AS.MIN and tCS.MIN [ns]
AH.MIN and tCH.MIN [ns]
DS.MIN [ns]
DH.MIN [ns]
WR.MIN [ns]
WTR.MIN [ns]
RTP.MIN [ns]
Analysis Characteristics
t
t
t
t
t
t
RC and tRFC Extension
RC.MIN [ns]
RFC.MIN [ns]
CK.MAX [ns]
DQSQ.MAX [ns]
QHS.MAX [ns]
PLL Relock Time
CASE.MAX Delta / ∆T4R4W Delta
T
Psi(T-A) DRAM
∆T0 (DT0)
∆T2N (DT2N, UDIMM) or ∆T2Q (DT2Q, RDIMM)
∆T2P (DT2P)
∆T3N (DT3N)
∆T3P.fast (DT3P fast)
∆T3P.slow (DT3P slow)
∆T4R (DT4R) / ∆T4R4W Sign (DT4R4W)
∆T5B (DT5B)
∆T7 (DT7)
Psi(ca) PLL
Psi(ca) REG
∆TPLL (DTPLL)
∆TREG (DTREG) / Toggle Rate
SPD Revision
Rev. 1.1, 2007-01
77
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
HYS64T128021EDL–3.7B2 HYS64T128921EDL–3.7B2
1 GByte
×64
1 GByte
×64
2 Ranks (×8)
PC2–4200S–444
Rev. 1.2
HEX
2 Ranks (×8)
PC2–4200S–444
Rev. 1.2
HEX
Label Code
JEDEC SPD Revision
Byte#
Description
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
Checksum of Bytes 0-62
Manufacturer’s JEDEC ID Code (1)
Manufacturer’s JEDEC ID Code (2)
Manufacturer’s JEDEC ID Code (3)
Manufacturer’s JEDEC ID Code (4)
Manufacturer’s JEDEC ID Code (5)
Manufacturer’s JEDEC ID Code (6)
Manufacturer’s JEDEC ID Code (7)
Manufacturer’s JEDEC ID Code (8)
Module Manufacturer Location
Product Type, Char 1
37
7F
7F
7F
7F
7F
51
00
00
xx
37
7F
7F
7F
7F
7F
51
00
00
xx
36
34
54
31
32
38
30
32
31
45
44
4C
33
2E
37
42
32
20
2x
xx
36
34
54
31
32
38
39
32
31
45
44
4C
33
2E
37
42
32
20
0x
xx
Product Type, Char 2
Product Type, Char 3
Product Type, Char 4
Product Type, Char 5
Product Type, Char 6
Product Type, Char 7
Product Type, Char 8
Product Type, Char 9
Product Type, Char 10
Product Type, Char 11
Product Type, Char 12
Product Type, Char 13
Product Type, Char 14
Product Type, Char 15
Product Type, Char 16
Product Type, Char 17
Product Type, Char 18
Module Revision Code
Test Program Revision Code
Module Manufacturing Date Year
Module Manufacturing Date Week
xx
xx
xx
xx
95 - 98 Module Serial Number
xx
xx
Rev. 1.1, 2007-01
78
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Product Type
Organization
HYS64T128021EDL–3.7B2 HYS64T128921EDL–3.7B2
1 GByte
×64
1 GByte
×64
2 Ranks (×8)
PC2–4200S–444
Rev. 1.2
HEX
2 Ranks (×8)
PC2–4200S–444
Rev. 1.2
HEX
Label Code
JEDEC SPD Revision
Byte#
Description
99 - 127 Not used
00
00
FF
128 -
255
Blank for customer use
FF
Rev. 1.1, 2007-01
79
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
5
Package Outlines
FIGURE 5
Package Outline Raw Card A L-DIM-200-31
ꢂꢇꢄꢂ
ꢆꢄꢉ -!8ꢄ
ꢀꢄꢅ
ꢂꢆꢄꢂ
ꢅꢌ
ꢅ
ꢅꢀꢀ
ꢊꢋꢄꢅꢈꢌ
ꢀꢄꢅ
ꢊꢋꢄꢃꢈꢌ
ꢀꢄꢅ
ꢅ
ꢅꢇꢄꢈꢈ
ꢀꢄꢅ
ꢋꢄꢇ
ꢊꢅꢄꢈꢌ
ꢀꢄꢅ
ꢅꢅꢄꢃ
ꢀꢄꢅ
ꢃꢇꢄꢃ
ꢊꢅꢄꢉꢌ
ꢊꢋꢄꢃꢈꢌ
ꢀꢄꢅ
ꢊꢋꢄꢅꢈꢌ
ꢋꢀꢀ
ꢋꢄꢃ
ꢀꢄꢅ
ꢅ
$ETAIL OF CONTACTS
ꢅꢀꢅ
ꢋꢌ
ꢀꢄꢀꢆ
ꢀꢄꢃꢈ
ꢀꢄꢅ
ꢀꢄꢂ
ꢋ -).ꢄ
$RAWING ACCORDING TO )3/ ꢉꢀꢅꢈ
'ENERAL TOLERANCES ꢀꢄꢅꢈ
$IMENSIONS IN MM
',$ꢀꢁꢂꢃꢁ
Notes
1. Thermal Sensor (Optional)
2. SPD or Combidevice (if used then no Thermal Sensor needed)
Rev. 1.1, 2007-01
80
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
FIGURE 6
Package Outline Raw Card C L-DIM-200-30
ꢂꢇꢄꢂ
ꢆꢄꢉ -!8ꢄ
ꢀꢄꢅ
ꢂꢆꢄꢂ
ꢅꢌ
ꢅ
ꢅꢀꢀ
ꢊꢋꢄꢅꢈꢌ
ꢀꢄꢅ
ꢊꢋꢄꢃꢈꢌ
ꢀꢄꢅ
ꢅ
ꢅꢇꢄꢈꢈ
ꢀꢄꢅ
ꢋꢄꢇ
ꢊꢅꢄꢈꢌ
ꢀꢄꢅ
ꢀꢄꢅ
ꢅꢅꢄꢃ
ꢀꢄꢅ
ꢃꢇꢄꢃ
ꢊꢅꢄꢉꢌ
ꢊꢋꢄꢃꢈꢌ
ꢀꢄꢅ
ꢊꢋꢄꢅꢈꢌ
ꢋꢀꢀ
ꢋꢄꢃ
ꢅ
$ETAIL OF CONTACTS
ꢅꢀꢅ
ꢋꢌ
ꢀꢄꢀꢆ
ꢀꢄꢃꢈ
ꢀꢄꢅ
ꢀꢄꢂ
ꢋ -).ꢄ
$RAWING ACCORDING TO )3/ ꢉꢀꢅꢈ
'ENERAL TOLERANCES ꢀꢄꢅꢈ
$IMENSIONS IN MM
',$ꢀꢁꢂꢃꢉ
Notes
1. Drawing according to ISO 8015
2. Dimensions in mm
3. General tolerances +/- 0.15
Rev. 1.1, 2007-01
81
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
FIGURE 7
Package Outline L-DIM-200-36
ꢂꢇꢄꢂ
ꢆꢄꢉ -!8ꢄ
ꢀꢄꢅ
ꢂꢆꢄꢂ
ꢅꢌ
ꢅ
ꢅꢀꢀ
ꢊꢋꢄꢅꢈꢌ
ꢀꢄꢅ
ꢊꢋꢄꢃꢈꢌ
ꢀꢄꢅ
ꢅ
ꢅꢇꢄꢈꢈ
ꢀꢄꢅ
ꢋꢄꢇ
ꢊꢅꢄꢈꢌ
ꢀꢄꢅ
ꢀꢄꢅ
ꢅꢅꢄꢃ
ꢀꢄꢅ
ꢃꢇꢄꢃ
ꢊꢅꢄꢉꢌ
ꢊꢋꢄꢃꢈꢌ
ꢀꢄꢅ
ꢊꢋꢄꢅꢈꢌ
ꢋꢀꢀ
ꢋꢄꢃ
ꢅ
$ETAIL OF CONTACTS
ꢅꢀꢅ
ꢀꢄꢀꢆ
ꢀꢄꢃꢈ
ꢀꢄꢅ
ꢀꢄꢂ
ꢋꢌ
ꢋ -).ꢄ
$RAWING ACCORDING TO )3/ ꢉꢀꢅꢈ
'ENERAL TOLERANCES ꢀꢄꢅꢆ
$IMENSION IN MM
',$ꢀꢅꢀꢂꢉ
Notes
1. Drawing according to ISO 8015
2. Dimensions in mm
3. General tolerances +/- 0.15
Rev. 1.1, 2007-01
82
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
6
Product Type Nomenclature
Qimonda’s nomenclature uses simple coding combined with some propriatory coding. Table 37 provides examples for module
and component product type number as well as the field number. The detailed field description together with possible values
and coding explanation is listed for modules in Table 38 and for components in Table 39.
TABLE 37
Nomenclature Fields and Examples
Example for
Field Number
1
2
3
4
5
6
7
8
9
10
11
Micro-DIMM
DDR2 DRAM
HYS
HYB
64
18
T
T
64/128
0
2
0
0
K
A
M
C
–5
–5
–A
—
512/1G 16
TABLE 38
DDR2 DIMM Nomenclature
Field
Description
Values
Coding
1
2
Qimonda Module Prefix
Module Data Width [bit]
HYS
64
Constant
Non-ECC
ECC
72
3
4
DRAM Technology
T
DDR2
Memory Density per I/O [Mbit];
Module Density1)
32
256 MByte
512 MByte
1 GByte
2 GByte
4 GByte
64
128
256
512
0 .. 9
0, 2, 4
0 .. 9
A .. Z
D
5
6
7
8
9
Raw Card Generation
Number of Module Ranks
Product Variations
Look up table
1, 2, 4
Look up table
Look up table
SO-DIMM
Package, Lead-Free Status
Module Type
M
Micro-DIMM
Registered
Unbuffered
Fully Buffered
R
U
F
Rev. 1.1, 2007-01
83
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Field
Description
Values
Coding
10
Speed Grade
–2.5F
–2.5
–3
PC2–6400 5–5–5
PC2–6400 6–6–6
PC2–5300 4–4–4
PC2–5300 5–5–5
PC2–4200 4–4–4
PC2–3200 3–3–3
First
–3S
–3.7
–5
11
Die Revision
–A
–B
Second
1) Multiplying “Memory Density per I/O” with “Module Data Width” and dividing by 8 for Non-ECC and 9 for ECC modules gives the overall
module memory density in MBytes as listed in column “Coding”.
TABLE 39
DDR2 DRAM Nomenclature
Field
Description
Values
Coding
1
2
3
4
Qimonda Component Prefix
Interface Voltage [V]
HYB
18
Constant
SSTL_18
DRAM Technology
T
DDR2
Component Density [Mbit]
256
512
1G
2G
40
256 Mbit
512 Mbit
1 Gbit
2 Gbit
5+6
Number of I/Os
×4
80
×8
16
×16
7
8
Product Variations
Die Revision
0 .. 9
A
Look up table
First
B
Second
9
Package, Lead-Free Status
Speed Grade
C
FBGA, lead-containing
FBGA, lead-free
DDR2-800 5-5-5
DDR2-800 6-6-6
DDR2-667 4-4-4
DDR2-667 5-5-5
DDR2-533 4-4-4
DDR2-400 3-3-3
F
10
–25F
–2.5
–3
–3S
–3.7
–5
Rev. 1.1, 2007-01
84
08212006-PKYN-2H1B
Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Table of Contents
1
1.1
1.2
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2
Pin Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1
Chip Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3
3.1
3.2
3.3
3.3.1
3.3.2
3.3.3
3.4
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
DC Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Timing Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Speed Grade Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
ODT AC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
I
DD Specifications and Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4
5
6
SPD Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Product Type Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Rev. 1.1, 2007-01
85
08212006-PKYN-2H1B
Internet Data Sheet
Edition 2007-01
Published by Qimonda AG
Gustav-Heinemann-Ring 212
D-81739 München, Germany
© Qimonda AG 2007.
All Rights Reserved.
Legal Disclaimer
The information given in this Internet Data Sheet shall in no event be regarded as a guarantee of conditions or characteristics
(“Beschaffenheitsgarantie”). With respect to any examples or hints given herein, any typical values stated herein and/or any
information regarding the application of the device, Qimonda hereby disclaims any and all warranties and liabilities of any kind,
including without limitation warranties of non-infringement of intellectual property rights of any third party.
Information
For further information on technology, delivery terms and conditions and prices please contact your nearest Qimonda Office.
Warnings
Due to technical requirements components may contain dangerous substances. For information on the types in question please
contact your nearest Qimonda Office.
Qimonda Components may only be used in life-support devices or systems with the express written approval of Qimonda, if a
failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect
the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human
body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health
of the user or other persons may be endangered.
www.qimonda.com
相关型号：
©2020 ICPDF网 联系我们和版权申明