ADC12441 [NSC]
Dynamically-Tested Self-Calibrating 12-Bit Plus Sign A/D Converter with Sample-and-Hold; 动态测试的自校准12位加符号位A / D转换器采样和保持型号: | ADC12441 |
厂家: | National Semiconductor |
描述: | Dynamically-Tested Self-Calibrating 12-Bit Plus Sign A/D Converter with Sample-and-Hold |
文件: | 总14页 (文件大小:276K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
November 1994
ADC12441 Dynamically-Tested Self-Calibrating 12-Bit
Plus Sign A/D Converter with Sample-and-Hold
General Description
Applications
Y
Digital signal processing
The ADC12441 is a CMOS 12-bit plus sign successive ap-
proximation analog-to-digital converter whose dynamic
specifications (S/N, THD, etc.) are tested and guaranteed.
On request, the ADC12441 goes through a self-calibration
cycle that adjusts positive linearity and full-scale errors to
Y
Telecommunications
Y
Audio
Y
High resolution process control
Y
Instrumentation
g
1 LSB. The ADC12441 also has the ability to go through
less than
g
(/2 LSB each and zero error to less than
Key Specifications
Y
an Auto-Zero cycle that corrects the zero error during every
conversion.
Resolution
12 bits plus sign
13.8 ms (max)
76.5 dB (min)
Y
Conversion Time
The analog input to the ADC12441 is tracked and held by
the internal circuitry, and therefore does not require an ex-
ternal sample-and-hold. A unipolar analog input voltage
Y
Bipolar Signal/Noise
Y
b
Total Harmonic Distortion
75 dB (max)
100 ns
Y
a
range (0V to 5V) or a bipolar range ( 5V to 5V) can be
accommodated with 5V supplies.
b
a
Aperture Time
Y
g
Aperture Jitter
100 ps
rms
Y
g
g
Zero Error
1 LSB (max)
1 LSB (max)
The 13-bit word on the outputs of the ADC12441 gives a 2’s
complement representation of negative numbers. The digi-
tal inputs and outputs are compatible with TTL or CMOS
logic levels.
Y
Positive Full Scale Error
Y
Y
@
g
Power Consumption
Sampling rate
5V
70 mW (max)
55 kHz (max)
Features
Y
Self-calibration provides excellent temperature stability
Y
Internal sample-and-hold
a
Bipolar input range with single 5V reference
Y
TRI-STATE is a registered trademark of National Semiconductor Corporation.
É
Simplified Block Diagram
Connection Diagram
Dual-In-Line Package
TL/H/11017–2
Top View
Order Number
ADC12441CMJ, ADC12441CMJ/883
or ADC12441CIJ
See NS Package Number J28A
TL/H/11017–1
C
1995 National Semiconductor Corporation
TL/H/11017
RRD-B30M115/Printed in U. S. A.
Absolute Maximum Ratings (Notes 1 & 2)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales
Office/Distributors for availability and specifications.
Operating Ratings (Notes 1 & 2)
s
s
T
Temperature Range
ADC12441CIJ
ADC12441CMJ,
ADC12441CMJ/883
T
40 C
§
T
A
MIN
s
A
MAX
85 C
§
s
b
a
T
s
s
a
b
55 C
§
T
125 C
§
e
e
AV
A
Supply Voltage (V
CC
DV
)
CC
6.5V
6.5V
CC
Negative Supply Voltage (Vb
DV
and AV
Voltage
CC
b
CC
(Notes 6 & 7)
)
4.5V to 5.5V
b
a
Voltage at Logic Control Inputs
Voltage at Analog Inputs
0.3V to (V
0.3V)
CC
Negative Supply Voltage (Vb
)
b
b
4.5V to 5.5V
(V and V
IN REF
)
(Vb 0.3V) to (V
0.3V)
0.3V
5 mA
Reference Voltage
, Notes 6 & 7)
REF
b
a
CC
a
50 mV
(V
3.5V to AV
CC
AV –DV (Note 7)
CC CC
g
Input Current at Any Pin (Note 3)
Package Input Current (Note 3)
g
20 mA
Power Dissipation at 25 C (Note 4)
§
Storage Temperature Range
ESD Susceptability (Note 5)
875 mW
b
a
65 C to 150 C
§
§
2000V
Soldering Information
J Package (10 sec.)
300 C
§
Converter Electrical Characteristics
CC
b
e
e
e a
e b
2.0 MHz unless otherwise specified. Boldface limits apply for T
e a
5.0V, Analog Input Source
The following specifications apply for V
CC
DV
AV
CC
5.0V, V
5.0V, V
REF
e
all other limits T
e
25 C. (Notes 6, 7 and 8)
e
e
T T
J
Impedance
600X, and f
to T
;
MAX
CLK
§
A
MIN
e
e
T
A
J
Typical Limit
(Note 9) (Note 10)
Units
(Limit)
Symbol
Parameter
Conditions
STATIC CHARACTERISTICS
Positive Integral Linearity Error
g
g
After Auto-Cal (Notes 11 & 12)
After Auto-Cal (Notes 11 & 12)
After Auto-Cal (Notes 11 & 12)
(/2
*/4
LSB
LSB
Bits
Negative Integral Linearity Error
Positive or Negative Differential Linearity
Zero Error
12
After Auto-Zero or Auto-Cal
(Notes 12 & 13)
g
g
1
1
LSB (max)
g
Positive Full-Scale Error
Negative Full-Scale Error
Analog Input Voltage
After Auto-Cal (Note 12)
After Auto-Cal (Note 12)
(/2
LSB (max)
LSB (max)
V(min)
g
g
2
1 /
V
IN
Vb
0.05
b
a
V
0.05 V(max)
CC
e
e
e
5V 5%,
g
g
g
g
Power Supply
Sensitivity
Zero Error (Note 14) AV
V
DV
CC
4.75V, V
(/8
(/8
(/8
LSB
LSB
LSB
pF
CC
b
e b
g
5V 5%
REF
Full-Scale Error
Linearity Error
C
C
V
REF
Input Capacitance (Note 18)
80
REF
Analog Input Capacitance
65
pF
IN
DYNAMIC CHARACTERISTICS
e
e
g
Bipolar Effective Bits
(Note 17)
f
f
f
f
f
f
f
f
f
f
1 kHz, V
IN
4.85V
12.6
12.6
11.8
11.8
78
Bits
IN
e
e
e
e
e
e
e
e
e
e
g
20 kHz, V
IN
4.85V
4.85 V
12.4
Bits (min)
Bits
IN
IN
IN
IN
IN
IN
IN
IN
IN
e
Unipolar Effective Bits
(Note 17)
1 kHz, V
IN
p-p
e
20 kHz, V
IN
4.85 V
11.6
Bits (min)
dB
p-p
e
g
S/N
S/N
Bipolar Signal-to-Noise Ratio
(Note 17)
1 kHz, V
IN
4.85V
e
g
10 kHz, V
4.85V
4.85V
78
dB
IN
IN
e
g
20 kHz, V
78
76.5
71.5
dB (min)
dB
e
Unipolar Signal-to-Noise Ratio
(Note 17)
1 kHz, V
IN
4.85 V
p-p
73
e
10 kHz, V
4.85 V
73
dB
IN
IN
p-p
p-p
e
20 kHz, V
4.85 V
73
dB (min)
2
Converter Electrical Characteristics
The following specifications apply for V
CC
b
e
e
e a
e b
2.0 MHz unless otherwise specified. Boldface limits apply for T
e a
5.0V, Analog Input Source
DV
CC
AV
5.0V, V
5.0V, V
REF
CC
e
all other limits T
e
25 C. (Notes 6, 7 and 8) (Continued)
e
e
T T
J
Impedance
600X, and f
to T
;
MAX
CLK
§
A
MIN
e
e
T
J
A
Typical
Limit
Units
(Note 9) (Notes 10, 19) (Limit)
Symbol
Parameter
Conditions
DYNAMIC CHARACTERISTICS (Continued)
e
e
e
e
e
e
e
e
e
e
e
b
g
THD
THD
Bipolar Total Harmonic Distortion
(Note 17)
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
1 kHz, V
IN
4.85V
82
80
82
80
88
84
80
90
86
82
dB
dB (max)
dB
e
b
b
b
b
b
b
b
b
b
b
b
g
19.688 kHz, V
IN
4.85V
75
75
e
Unipolar Total Harmonic Distortion
(Note 17)
1 kHz, V
IN
4.85 V
p-p
e
19.688 kHz, V
4.85 V
p-p
dB (max)
dB
IN
e
g
Bipolar Peak Harmonic or
Spurious Noise (Note 17)
1 kHz, V
IN
4.85V
e
g
10 kHz, V
4.85V
4.85V
dB
IN
IN
e
g
20 kHz, V
dB
e
Unipolar Peak Harmonic or
Spurious Noise (Note 17)
1 kHz, V
IN
4.85 V
p-p
dB
e
10 kHz, V
20 kHz, V
4.85 V
4.85 V
dB
IN
IN
p-p
p-p
e
dB
e
e
e
g
20.625 kHz
Bipolar Two Tone Intermodulation
Distortion (Note 17)
V
4.85V, f
IN1
19.375 kHz,
IN
b
b
b
b
78
78
74
73
dB (max)
dB (max)
f
IN2
e
e
e
19.375 kHz,
Unipolar Two Tone Intermodulation
Distortion (Note 17)
V
IN
4.85 V , f
p-p IN1
20.625 kHz
f
IN2
b
e
e
g
3 dB Bipolar Full Power Bandwidth
V
4.85V (Note 17)
25
20
20
kHz (Min)
kHz (Min)
ns
IN
IN
b
3 dB Unipolar Full Power Bandwidth
V
4.85 V (Note 17)
p-p
30
Aperture Time
Aperture Jitter
100
100
ps
rms
Digital and DC Electrical Characteristics
5.0V, V
b
e
otherwise specified. Boldface limits apply for T
e a
e b
e a
; all other limits T
e
2.0 MHz unless
CLK
The following specifications apply for DV
CC
AV
CC
e
5.0V, V
REF
5.0V, and f
e
e
e
T 25 C.
J
T
J
T
to T
§
A
MIN
MAX
A
(Notes 6 and 7)
Typical
(Note 9)
Limit
Units
Symbol
Parameter
Conditions
(Notes 10, 19)
(Limits)
e
e
V
V
Logical ‘‘1’’ Input Voltage for
All Inputs except CLK IN
V
V
5.25V
4.75V
IN(1)
IN(0)
IN(1)
CC
2.0
V (min)
Logical ‘‘0’’ Input Voltage for
All Inputs except CLK IN
CC
0.8
1
V (max)
e
I
I
Logical ‘‘1’’ Input Current
Logical ‘‘0’’ Input Current
V
V
5V
0.005
mA (max)
mA (max)
IN
e
b
b
1
0V
0.005
2.8
IN(0)
IN
a
V
V
V
V
CLK IN Positive-Going
Threshold Voltage
T
2.7
2.3
0.4
V (min)
V (max)
V (min)
b
CLK IN Negative-Going
Threshold Voltage
T
2.1
0.7
CLK IN Hysteresis
a
H
b
b
[
]
V
(min)
V
T
(max)
T
e
4.75V:
Logical ‘‘1’’ Output Voltage
V
V
OUT(1)
CC
e b
e b
I
I
360 mA
10 mA
2.4
4.5
V (min)
V (min)
OUT
OUT
e
e
1.6 mA
V
Logical ‘‘0’’ Output Voltage
4.75V, I
OUT
0.4
V (max)
OUT(0)
CC
3
Digital and DC Electrical Characteristics
5.0V, V
b
e
otherwise specified. Boldface limits apply for T
e a
e b
e a
; all other limits T
e
5.0V, and f 2.0 MHz unless
CLK
The following specifications apply for DV
CC
AV
5.0V, V
REF
CC
e
e
e
e
T 25 C.
J
T
T
MIN
to T
§
A
J
MAX
A
(Notes 6 and 7) (Continued)
Typical
(Note 9)
Limit
(Notes 10, 19)
Units
Symbol
Parameter
Conditions
(Limits)
e
b
b
3
I
TRI-STATE Output Leakage
É
Current
V
V
V
V
0V
5V
0V
5V
0.01
mA (max)
mA (max)
mA (min)
mA (min)
mA (max)
mA (max)
mA (max)
OUT
OUT
OUT
OUT
OUT
e
0.01
3
e
e
b
b
6.0
8.0
I
I
Output Source Current
Output Sink Current
20
SOURCE
20
SINK
e
e
DI
DV Supply Current
CC
f
f
f
2 MHz, CS
2 MHz, CS
2 MHz, CS
‘‘1’’
‘‘1’’
‘‘1’’
1
2
6
6
CC
CC
CLK
CLK
CLK
e
e
e
e
AI
AV Supply Current
CC
2.8
2.8
Ib
Vb Supply Current
AC Electrical Characteristics
The following specifications apply for DV
CC
b
e
e a
e b
e
e
t 20 ns unless otherwise specified.
f
AV
CC
5.0V, V
; all other limits T
5.0V, t
e
T
J
r
e
e
e
Boldface limits apply for T
T
T
MIN
to T
25 C. (Notes 6 and 7)
§
A
J
MAX
A
Typical
(Note 9)
Limit
Units
Symbol
Parameter
Clock Frequency
Conditions
(Notes 10, 19)
(Limits)
f
CLK
0.5
4.0
MHz (min)
MHz (max)
2.0
Clock Duty Cycle
Conversion Time
50
%
40
60
% (min)
% (max)
a
)
CLK
t
t
t
t
27(1/f
)
27(1/f
300 ns
(max)
ms
C
CLK
e
f
2.0 MHz
13.5
7(1/f
CLK
e
2.0 MHz
a
300 ns
Acquisition Time
(Note 15)
R
50X
)
7(1/f
)
(max)
ms
A
SOURCE
e
CLK
3.5
26(1/f
CLK
f
CLK
Auto Zero Time
)
26(1/f
)
(max)
ms
Z
CLK
CLK
e
e
f
f
2.0 MHz
2.0 MHz
13
1396(1/f
698
CLK
Calibration Time
)
CLK
max
CAL
706
200
200
ms (max)
ns (min)
ns (min)
CLK
t
t
t
Calibration Pulse Width
(Note 16)
60
W(CAL)L
W(WR)L
ACC
Minimum WR Pulse Width
Maximum Access Time
60
e
C
100 pF
L
(Delay from Falling Edge of
RD to Output Data Valid)
50
85
ns (max)
e
e
t
t
, t
0H 1H
TRI-STATE Control
(Delay from Rising Edge of
RD to Hi-Z State)
R
1 kX,
L
C
L
100 pF
30
90
ns (max)
ns (max)
Maximum Delay from Falling Edge of
RD or WR to Reset of INT
PD(INT)
100
175
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed
specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test
conditions.
Note 2: All voltages are measured with respect to AGND and DGND, unless otherwise specified.
b
k
l
(AV or DV ), the current at that pin should be limited to
CC CC
Note 3: When the input voltage (V ) at any pin exceeds the power supply rails (V
IN
V
or V
IN
IN
5 mA. The 20 mA maximum package input current rating allows the voltage at any four pins, with an input current limit of 5 mA, to simultaneously exceed the power
supply voltages.
4
AC Electrical Characteristics (Continued)
a
Note 4: The power dissipation of this device under normal operation should never exceed 169 mW (Quiescent Power Dissipation
outputs). Caution should be taken not to exceed absolute maximum power rating when the device is operating in a severe fault condition (ex. when any inputs or
outputs exceed the power supply). The maximum power dissipation must be derated at elevated temperatures and is dictated by T (maximum junction
TTL Loads on the digital
Jmax
temperature), i (package junction to ambient thermal resistance), and T (ambient temperature). The maximum allowable power dissipation at any temperature
JA
A
e
b
e
125 C, and the typical thermal
Jmax
is P
Dmax
(T
T
A
)/i or the number given in the Absolute Maximum Ratings, whichever is lower. For this device, T
§
Jmax
JA
resistance (i ) of the ADC12441 with CMJ and CIJ suffixes when board mounted is 47 C/W.
§
JA
Note 5: Human body model, 100 pF discharged through a 1.5 kX resistor.
Note 6: Two on-chip diodes are tied to the analog input as shown below. Errors in the A/D conversion can occur if these diodes are forward biased more than
50 mV.
TL/H/11017–3
are minimum (4.75 V ) and Vb is maximum ( 4.75 V ), full-scale must be
s
b
This means that if AV
and DV
4.8 V
.
DC
CC
CC
DC
DC
Note 7: A diode exists between AV
and DV
as shown below.
CC
CC
TL/H/11017–4
To guarantee accuracy, it is required that the AV
and DV
be connected together to a power supply with separate bypass filters at each V pin.
CC
CC
CC
e
Note 8: Accuracy is guaranteed at f
2.0 MHz. At higher and lower clock frequencies accuracy may degrade. See curves in the Typical Performance
CLK
Characteristics section.
e
Note 9: Typicals are at T
25 C and represent most likely parametric norm.
§
Note 10: Limits are guaranteed to National’s AOQL (Average Outgoing Quality Level).
J
Note 11: Positive linearity error is defined as the deviation of the analog value, expressed in LSBs, from the straight line that passes through positive full scale and
zero. For negative linearity error the straight line passes through negative full scale and zero. (See Figures 1b and 1c.)
Note 12: The ADC12441’s self-calibration technique ensures linearity, full scale, and offset errors as specified, but noise inherent in the self-calibration process will
g
result in a repeatability uncertainty of 0.20 LSB.
Note 13: If T changes then an Auto-Zero or Auto-Cal cycle will have to be re-started (see the Typical Performance Characteristic curves).
A
Note 14: After an Auto-Zero or Auto-Cal cycle at the specified power supply extremes.
Note 15: If the clock is asynchronous to the falling edge of WR an uncertainty of one clock period will exist in the interval of t , therefore making the minimum
A
e
periods.
e
7 clock periods. If the falling edge of the clock is synchronous to the rising edge of WR then t will be exactly 6.5 clock
t
6 clock periods and the maximum t
A
A
A
Note 16: The CAL line must be high before a conversion is started.
Note 17: The specifications for these parameters are valid after an Auto-Cal cycle has been completed.
Note 18: The ADC12441 reference ladder is composed solely of capacitors.
Note 19: A Military RETS Electrical Test Specification is available on request. At time of printing the ADC12441CMJ/883 RETS complies fully with the boldface
limits in this column.
TL/H/11017–5
FIGURE 1a. Transfer Characteristic
5
Electrical Characteristics (Continued)
TL/H/11017–6
FIGURE 1b. Simplified Error Curve vs Output Code without Auto-Cal or Auto-Zero Cycles
TL/H/11017–7
FIGURE 1c. Simplified Error Curve vs Output Code after Auto-Cal Cycle
Typical Performance Characteristics
Zero Error Change vs
Ambient Temperature
Zero Error vs V
REF
TL/H/11017–8
6
Typical Performance Characteristics (Continued)
Linearity Error vs Clock
Frequency
Full Scale Error Change vs
Ambient Temperature
Linearity Error vs V
REF
s
e
ut
se
ut
TL/H/11017–9
7
Typical Performance Characteristics (Continued)
Bipolar Spectral Response
with 20 kHz Sine Wave Input
Unipolar Spectral Response
with 20 kHz Sine Wave Input
TL/H/11017–11
TL/H/11017–10
Test Circuits
TL/H/11017–13
TL/H/11017–12
TL/H/11017–15
TL/H/11017–14
FIGURE 2. TRI-STATE Test Circuits and Waveforms
Timing Diagrams
e
e
e
e
e
X, X Don’t Care)
Auto-Cal Cycle (CS
1, WR
X, RD
X, AZ
TL/H/11017–16
8
Timing Diagrams (Continued)
e
e
0)
Normal Conversion with Auto-Zero (CAL
1, AZ
TL/H/11017–17
e
e
1)
Normal Conversion without Auto-Zero (CAL
1, AZ
TL/H/11017–18
9
1.0 Pin Descriptions
DV
CC
AV
(28),
(4)
DB0–DB12
(15–27)
The digital and analog positive power supply
pins. The digital and analog power supply
The TRI-STATE output pins. The output is in
two’s complement format with DB12 the sign
bit, DB11 the MSB and DB0 the LSB.
CC
a
voltage range of the ADC12441 is 4.5V to
a
5.5V. To guarantee accuracy, it is required
that the AV and DV be connected to-
gether to the same power supply with sepa-
CC CC
2.0 Functional Description
The ADC12441 is a 12-bit plus sign A/D converter with the
capability of doing Auto-Zero or Auto-Cal routines to mini-
mize zero, full-scale and linearity errors. It is a successive-
approximation A/D converter consisting of a DAC, compar-
ator and a successive-approximation register (SAR). Auto-
Zero is an internal calibration sequence that corrects for the
A/D’s zero error caused by the comparator’s offset voltage.
Auto-Cal is a calibration cycle that not only corrects zero
error but also corrects for full-scale and linearity errors
caused by DAC inaccuracies. Auto-Cal minimizes the errors
of the ADC12441 without the need of trimming during its
fabrication. An Auto-Cal cycle can restore the accuracy of
the ADC12441 at any time, which ensures its long term sta-
bility.
rate bypass filters (10 mF tantalum in parallel
with a 0.1 mF ceramic) at each V
pin.
CC
The analog negative supply voltage pin. Vb
Vb (5)
b
b
has a range of 4.5V to 5.5V and needs a
bypass filter of 10 mF tantalum in parallel with
a 0.1 mF ceramic.
DGND (14), The digital and analog ground pins. AGND
and DGND must be connected together ex-
ternally to guarantee accuracy.
AGND (3)
V
V
(2)
The reference input voltage pin. To maintain
accuracy the voltage at this pin should not
REF
exceed the AV or DV by more than
CC CC
50 mV or go below 3.5 VDC.
(1)
The analog input voltage pin. To guarantee
accuracy the voltage at this pin should not
2.1 DIGITAL INTERFACE
IN
On power up, a calibration sequence should be initiated by
pulsing CAL low with CS, RD, and WR high. To acknowl-
edge the CAL signal, EOC goes low after the falling edge of
CAL, and remains low during the calibration cycle of 1396
clock periods. During the calibration sequence, first the
comparator’s offset is determined, then the capacitive
DAC’s mismatch error is found. Correction factors for these
errors are then stored in internal RAM.
exceed V by more than 50 mV or go below
CC
Vb by more than 50 mV.
CS (10)
RD (11)
WR (7)
The Chip Select control input. This input is
active low and enables the WR and RD func-
tions.
The Read control input. With both CS and RD
low the TRI-STATE output buffers are en-
abled and the INT output is reset high.
A conversion is initiated by taking CS and WR low. The AZ
(Auto Zero) signal line should be tied high or low during the
conversion process. If AZ is low an auto zero cycle, which
takes approximately 26 clock periods, occurs before the ac-
tual conversion is started. The auto zero cycle determines
the correction factors for the comparator’s offset voltage. If
AZ is high, the auto zero cycle is skipped. Next the analog
input is sampled for 7 clock periods, and held in the capaci-
tive DAC’s ladder structure. The EOC then goes low, signal-
ing that the analog input is no longer being sampled and
that the A/D successive approximation conversion has
started.
The Write control input. The converison is
started on the rising edge of the WR pulse
when CS is low.
CLK (8)
CAL (9)
The external clock input pin. The clock fre-
quency range is 500 kHz to 4 MHz.
The Auto-Calibration control input. When
CAL is low the ADC12441 is reset and a cali-
bration cycle is initiated. During the calibra-
tion cycle the values of the comparator offset
voltage and the mismatch errors in the ca-
pacitor reference ladder are determined and
stored in RAM. These values are used to cor-
rect the errors during a normal cycle of A/D
conversion.
During a conversion, the sampled input voltage is succes-
sively compared to the output of the DAC. First, the ac-
quired input voltage is compared to analog ground to deter-
mine its polarity. The sign bit is set low for positive input
voltages and high for negative. Next the MSB of the DAC is
set high with the rest of the bits low. If the input voltage is
greater than the output of the DAC, then the MSB is left
high; otherwise it is set low. The next bit is set high, making
the output of the DAC three quarters or one quarter of full
scale. A comparison is done and if the input is greater than
the new DAC value this bit remains high; if the input is less
than the new DAC value the bit is set low. This process
continues until each bit has been tested. The result is then
stored in the output latch of the ADC12441. Next EOC goes
high, and INT goes low to signal the end of the conversion.
The result can now be read by taking CS and RD low to
enable the DB0–DB12 output buffers.
AZ (6)
The Auto-Zero control input. With the AZ pin
held low during a conversion, the ADC12441
goes into an auto-zero cycle before the actu-
al A/D conversion is started. This Auto-Zero
cycle corrects for the comparator offset volt-
age. The total conversion time (t ) is in-
C
creased by 26 clock periods when Auto-Zero
is used.
EOC (12)
INT (13)
The End-of-Conversion control output. This
output is low during a conversion or a calibra-
tion cycle.
The Interrupt control output. This output goes
low when a conversion has been completed
and indicates that the conversion result is
available in the output latches. Reading the
result or starting a conversion or calibration
cycle will reset this output high.
10
2.0 Functional Description (Continued)
Digital Control Inputs
A/D Function
CS WR RD CAL AZ
ß
ß
ß
ß
1
ß
1
1
ß
1
1
1
1
1
0
0
X
X
Start Conversion without Auto-Zero
Read Conversion Result without Auto-Zero
Start Conversion with Auto-Zero
ß
1
1
ß
X
1
Read Conversion Result with Auto-Zero
Start Calibration Cycle
X
ß
0
0
X
1
Test Mode (DB2, DB3, DB5 and DB6 become active)
FIGURE 1. Function of the A/D Control Inputs
The table in Figure 1 summarizes the effect of the digital
control inputs on the function of the ADC12441. The Test
Mode, where RD is high and CS and CAL are low, is used
during manufacture to thoroughly check out the operation of
the ADC12441. Care should be taken not to inadvertently
be in this mode, since DB2, DB3, DB5, and DB6 become
active outputs, which may cause data bus contention.
3.0 Analog Considerations
3.1 REFERENCE VOLTAGE
The voltage applied to the reference input of the converter
defines the voltage span of the analog input (the difference
between V and AGND), over which 4095 positive output
IN
codes and 4096 negative output codes exist. The A-to-D
can be used in either ratiometric or absolute reference ap-
2.2 RESETTING THE A/D
plications. The voltage source driving V
must have a
REF
All internal logic can be reset, which will abort any conver-
sion in process. The A/D is reset whenever a new conver-
sion is started by taking CS and WR low. If this is done when
the analog input is being sampled or when EOC is low, the
Auto-Cal correction factors may be corrupted, therefore re-
quiring an Auto-Cal cycle before the next conversion. This is
true with or without Auto-Zero. The Calibration Cycle cannot
be reset once started. On power-up the ADC12441 auto-
matically goes through a Calibration Cycle that takes typi-
cally 1396 clock cycles. For reasons that will be discussed
in Section 3.7, a new calibration cycle needs to be started
after the completion of the automatic one.
very low output impedance and very low noise. The circuit in
Figure 2a is an example of a very stable reference that is
appropriate for use with the ADC12441. The simple refer-
ence circuit of Figure 2b may be used when the application
does not require low full scale errors.
In a ratiometric system, the analog input voltage is propor-
tional to the voltage used for the A/D reference. When this
voltage is the system power supply, the V
REF
pin can be
tied to V . This technique relaxes the stability requirement
CC
of the system reference as the analog input and A/D refer-
ence move together maintaining the same output code for
given input condition.
TL/H/11017–19
*Tantalum
**Ceramic
FIGURE 2a. Low Drift Extremely Stable Reference Circuit
Errors without any trims:
b
a
40 C to 85 C
§ §
25 C
§
0.075%
0.024%
g
g
g
0.2%
Full Scale
Zero
g
0.024%
g
g
(/2 LSB
Linearity
(/2 LSB
TL/H/11017–20
FIGURE 2b. Simple Reference Circuit
11
3.0 Analog Considerations (Continued)
For absolute accuracy, where the analog input varies be-
tween very specific voltage limits, the reference pin can be
biased with a time and temperature stable voltage source.
In general, the magnitude of the reference voltage will re-
quire an initial adjustment to null out full-scale errors.
with 0.1 mF ceramic capacitors are recommended for supply
bypassing. Separate bypass capacitors whould be placed
close to the DV , AV
CC
voltage source is available in the system,
and Vb pins. If an unregulated
CC
a
separate
(and
LM340LAZ-5.0 voltage regulator for the A-to-D’s V
CC
other analog circuitry) will greatly reduce digital noise on the
supply line.
3.2 INPUT CURRENT
Because the input network of the ADC12441 is made up of
a switch and a network of capacitors, a charging current will
flow into or out of (depending on the input voltage polarity)
3.7 THE CALIBRATION CYCLE
On power up the ADC12441 goes through an Auto-Cal cy-
cle which cannot be interrupted. Since the power supply,
reference, and clock will not be stable at power up, this first
calibration cycle will not result in an accurate calibration of
the A/D. A new calibration cycle needs to be started after
the power supplies, reference, and clock have been given
enough time to stabilize. During the calibration cycle, cor-
rection values are determined for the offset voltage of the
sampled data comparator and any linearity and gain errors.
These values are stored in internal RAM and used during an
analog-to-digital conversion to bring the overall full scale,
offset, and linearity errors down to the specified limits. Full
of the analog input pin (V ) on the start of the analog input
IN
sampling period (t ). The peak value of this current will de-
A
pend on the actual input voltage applied.
3.3 NOISE
The leads to the analog input pin should be kept as short as
possible to minimize input noise coupling. Both noise and
undesired digital clock coupling to this input can cause er-
rors. Input filtering can be used to reduce the effects of
these noise sources.
3.4 INPUT BYPASS CAPACITORS
g
scale error typically changes 0.1 LSB over temperature
An external capacitor can be used to filter out any noise due
to inductive pickup by a long input lead and will not degrade
the accuracy of the conversion result.
and linearity error changes even less; therefore it should be
necessary to go through the calibration cycle only once af-
ter power up, if auto-zero is used to correct the zero error
change.
3.5 INPUT SOURCE RESISTANCE
The analog input can be modeled as shown in Figure 3.
External R will lengthen the time period necessary for the
3.8 THE AUTO-ZERO CYCLE
S
To correct for any change in the zero (offset) error of the
A/D, the auto-zero cycle can be used. It may be necessary
to do an auto-zero cycle whenever the ambient temperature
changes significantly. (See the curved titled ‘‘Zero Error
Change vs Ambient Temperature’’ in the Typical Perform-
ance Characteristics.) A change in the ambient temperature
voltage on C
REF
input voltage. With f
CLK
to settle to within (/2 LSB of the analog
e
7 clock periods
e
e
2 MHz t
A
s
settle properly.
3.5 ms, R
1 kX will allow a 5V analog input voltage to
S
3.6 POWER SUPPLIES
and Vb supply lines can cause
will cause the V
of the sampled data comparator to
OS
change, which may cause the zero error of the A/D to be
Noise spikes on the V
CC
conversion errors as the comparator will respond to this
noise. The A/D is especially sensitive during the auto-zero
or auto-cal procedures to any power supply spikes. Low in
ductance tantalum capacitors of 10 mF or greater paralleled
g
greater than 1 LSB. An auto-zero cycle will maintain the
g
zero error to 1 LSB or less.
TL/H/11017–21
FIGURE 3. Analog Input Equivalent Circuit
12
4.0 Dynamic Performance
Many applications require the A/D converter to digitize ac
signals, but the standard dc integral and differential nonlin-
earity specifications will not accurately predict the A/D con-
verter’s performance with ac input signals. The important
specifications for ac applications reflect the converter’s abil-
ity to digitize ac signals without significant spectral errors
and without adding noise to the digitized signal. Dynamic
characteristics such as signal-to-noise ratio (S/N), signal-to-
to respond to the hold command. In the case of the
ADC12441, the hold command is internally generated.
When the Auto-Zero function is not being used, the hold
command occurs at the end of the acquisition window, or
seven clock periods after the rising edge of the WR. The
delay between the internally generated hold command and
the time that the ADC12441 actually holds the input signal is
the aperture time. For the ADC12441, this time is typically
100 ns. Aperture jitter is the change in the aperture time
from sample to sample. Aperture jitter is useful in determin-
ing the maximum slew rate of the input signal for a given
accuracy. For example, an ADC12441 with 100 ps of aper-
ture jitter operating with a 5V reference can have an effec-
tive gain variation of about 1 LSB with an input signal whose
slew rate is 12 V/ms.
a
a
noise distortion ratio (S/(N D)), effective bits, full power
bandwidth, aperture time and aperture jitter are quantitative
measures of the A/D converter’s capability.
An A/D converter’s ac performance can be measured using
Fast Fourier Transform (FFT) methods. A sinusoidal wave-
form is applied to the A/D converter’s input, and the trans-
a
form is then performed on the digitized waveform. S/(N D)
and S/N are calculated from the resulting FFT data, and a
spectral plot may also be obtained. Typical values for S/N
are shown in the table of Electrical Characteristics, and
Power Supply Bypassing
a
spectral plots of S/(N D) are included in the typical per-
formance curves.
The A/D converter’s noise and distortion levels will change
with the frequency of the input signal, with more distortion
and noise occurring at higher signal frequencies. This can
a
be seen in the S/(N D) versus frequency curves. These
curves will also give an indication of the full power band-
a
width (the frequency at which the S/(N D) or S/N drops
3 dB).
Effective number of bits can also be useful in describing the
A/D’s noise performance. An ideal A/D converter will have
some amount of quantization noise, determined by its reso-
lution, which will yield an optimum S/N ratio given by the
following equation:
TL/H/11017–22
*Tantalum
**Ceramic
e
c
a
n 1.8)dB
S/N
(6.02
Protecting the Analog Inputs
where n is the A/D’s resolution in bits.
The effective bits of a real A/D converter, therefore, can be
found by:
b
S/N(dB) 1.8
e
n(effective)
6.02
g
As an example, an ADC12441 with a 5V, 10 kHz sine
wave input signal will typically have a S/N of 78 dB, which is
equivalent to 12.6 effective bits.
Two sample/hold specifications, aperture time and aperture
jitter, are included in the Dynamic Characteristics table
since the ADC12441 has the ability to track and hold the
analog input voltage. Aperture time is the delay for the A/D
TL/H/11017–23
Note: External protection diodes should be able to withstand the op amp
current limit.
13
Physical Dimensions inches (millimeters)
Order Number ADC12441CMJ, ADC12441CMJ/883, or ADC12441CIJ
NS Package Number J28A
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL
SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and whose
failure to perform, when properly used in accordance
with instructions for use provided in the labeling, can
be reasonably expected to result in a significant injury
to the user.
2. A critical component is any component of a life
support device or system whose failure to perform can
be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or
effectiveness.
National Semiconductor
Corporation
National Semiconductor
Europe
National Semiconductor
Hong Kong Ltd.
National Semiconductor
Japan Ltd.
a
1111 West Bardin Road
Arlington, TX 76017
Tel: 1(800) 272-9959
Fax: 1(800) 737-7018
Fax:
(
49) 0-180-530 85 86
@
13th Floor, Straight Block,
Ocean Centre, 5 Canton Rd.
Tsimshatsui, Kowloon
Hong Kong
Tel: (852) 2737-1600
Fax: (852) 2736-9960
Tel: 81-043-299-2309
Fax: 81-043-299-2408
Email: cnjwge tevm2.nsc.com
a
a
a
a
Deutsch Tel:
English Tel:
Fran3ais Tel:
Italiano Tel:
(
(
(
(
49) 0-180-530 85 85
49) 0-180-532 78 32
49) 0-180-532 93 58
49) 0-180-534 16 80
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
相关型号:
ADC12441883
Dynamically-Tested Self-Calibrating 12-Bit Plus Sign A/D Converter with Sample-and-Hold
NSC
ADC12441CIJ
Dynamically-Tested Self-Calibrating 12-Bit Plus Sign A/D Converter with Sample-and-Hold
NSC
ADC12441CIJ/NOPB
1-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, CDIP28, CERAMIC, DIP-28
TI
ADC12441CMJ
Dynamically-Tested Self-Calibrating 12-Bit Plus Sign A/D Converter with Sample-and-Hold
NSC
ADC12451
Dynamically-Tested Self-Calibrating 12-Bit Plus Sign A/D Converter with Sample-and-Hold
NSC
ADC12451883
Dynamically-Tested Self-Calibrating 12-Bit Plus Sign A/D Converter with Sample-and-Hold
NSC
ADC12451CIJ
Dynamically-Tested Self-Calibrating 12-Bit Plus Sign A/D Converter with Sample-and-Hold
NSC
ADC12451CMJ
Dynamically-Tested Self-Calibrating 12-Bit Plus Sign A/D Converter with Sample-and-Hold
NSC
©2020 ICPDF网 联系我们和版权申明