M52742SP [MITSUBISHI]
BUS CONTROLLED 3-CHANNEL VIDEO PREAMP FOR CRT DISPLAY MONITOR; 总线控制3路视频前置放大器CRT显示器型号: | M52742SP |
厂家: | Mitsubishi Group |
描述: | BUS CONTROLLED 3-CHANNEL VIDEO PREAMP FOR CRT DISPLAY MONITOR |
文件: | 总21页 (文件大小:146K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MITSUBISHI ICs (Monitor)
PRELIMINARY
M52742SP
Notice:This is not a final specification.
Some parametric limits are subject to change.
BUS CONTROLLED 3-CHANNEL VIDEO PREAMP FOR CRT DISPLAY MONITOR
DESCRIPTION
M52742SP is semiconductor integrated circuit for CRT display
PIN CONFIGURATION (TOP VIEW)
monitor.
It includes OSD blanking, OSD mixing, retrace blanking, wide band
amplifre, brightness control, uniformity function.
Main/sub contrast and OSD adjust function can be controlled by I2C
bus.
1
2
3
4
5
6
7
8
9
36
35
34
OSD BLK IN
INPUT(R)
VCC1(R)
VCC2
OUTPUT(R)
EXT FEED BACK(R)
OSD IN(R)
GND 1(R)
INPUT(G)
INPUT(SOG)
VCC1(G)
33 GND2
32
31
30
29
OUTPUT(G)
FEATURES
EXT FEED BACK(G)
MAIN BRIGHTNESS
OUTPUT(B)
• Frequency band width: RGB.............................200MHz (at -3dB)
OSD..............................................80MHz
Input :RGB.............................................................0.7VP-P (typ.)
OSD..........................................3VP-P minimum (positive)
BLK (for OSD)..........................3VP-P minimum (positive)
Retrace BLK.............................3VP-P minimum (positive)
Output :RGB..........................................................5.5VP-P (max.)
OSD..............................................................5VP-P (max.)
• Main contrast and sub contrast can be controlled by I2C bus.
• Include internal and external pedestal clamp circuit
OSD IN(G)
28 EXT FEED BACK(B)
27 RETRACE BLK IN
GND 1(G) 10
11
12
13
14
26
25
24
23
INPUT(B)
VCC1(B)
D/A OUT1
D/A OUT2
D/A OUT3
D/A OUT4
OSD IN(B)
GND 1(B)
STRUCTURE
Bipola silicon monolisic IC
ABL IN 15
22 GND(5V)
16
17
18
21
20
19
UNIFORMITY IN
VCC=5V
SDA
SCL
APPLICATION
CRT display monitor
SOG SEP OUT
CLAMP PULSE IN
Outline 36P4E
RECOMMENDED OPERATING CONDITION
Supply voltage range......................11.5 to 12.5V (V3, V8, V12, V36)
4.5 to 4.4V (V17)
Rated supply voltage..................................12.0V (V3, V8, V12, V36)
5.0V (V17)
MAJOR SPECIFICATION
Bus controlled 3ch video pre-amp with OSD mixing function and
retrace blanking function
1
MITSUBISHI ICs (Monitor)
PRELIMINARY
M52742SP
Notice:This is not a final specification.
Some parametric limits are subject to change.
BUS CONTROLLED 3-CHANNEL VIDEO PREAMP FOR CRT DISPLAY MONITOR
BLOCK DIAGRAM
2
MITSUBISHI ICs (Monitor)
PRELIMINARY
M52742SP
Notice:This is not a final specification.
Some parametric limits are subject to change.
BUS CONTROLLED 3-CHANNEL VIDEO PREAMP FOR CRT DISPLAY MONITOR
ABSOLUTE MAXIMUM RATINGS (Ta=25°C)
Symbol
VCC
Pd
Parameter
Ratings
13.0
Unit
V
Supply voltage
Power dissipation
Ambient temperature
Storage temperature
Recommended supply
Voltage range
2403
mW
°C
°C
V
Topr
-20 to +75
-40 to +150
12.0
Tstg
Vopr
Vopr’
10.5 to 12.5
V
ELECTRICAL CHARACTERISTICS (VCC=12V, 5V, Ta=25°C, unless otherwise noted)
CTL
voltage
Input
19
CP in ReT
BLK
BUS CTL (H)
Limits
Test
point
(s)
Symbol
Parameter
Unit
0BH
INT
EXT
4,9,13
OSD
in
00H 01H 02H 03H 04H 05H 06H 07H 08H 09H
Main Sub Sub Sub OSD BLK D/A D/A D/A D/A
cont cont cont cont Adj Adj OUT OUT OUT OUT
1
OSD
BLK
7
SOG
in
2,6,11
RGB
in
27
16
UNI
in
15
ABL
30
Bri-
ght
Min. Typ. Max.
1
2
3
1
2
3
4
b
a
Circuit
FFH FFH FFH FFH 00H 00H FFH FFH FFH FFH 00H
ICC1
IA
IB
a
a
a
a
a
a
a
a
a
a
a
a
a
a
4.0 5.0
4.0 5.0
−
−
110 130 mA
18 25 mA
255 255 255 255
0
0
255 255 255 255
0
current1
SG5
b
a
Circuit
current2
ICC2
SG5
b
SG2
b
a
Vari
5.0
Output
dynamic range
Vomax
OUT
6.0 8.0
1.6
−
−
VP-P
VP-P
able
SG5
b
IN
OUT
b
a
Maximum
input
64H
100
Vimax
a
a
a
a
2.0 5.0
2.0 5.0
−
SG2
Variable
SG5
b
SG1
b
a
Maximum
gain
FFH
255
Gv
OUT
a
a
a
a
16.5 17.7 19.4
0.8 1.0 1.2
dB
SG5
Relative max-
imum gain
∆Gv
−
−
−
−
−
−
−
−
−
−
−
−
Main contrast
control
characteristics1
b
SG1
b
SG5
C8H
200
VC1
OUT
−
a
−
a
−
a
−
a
−
a
−
a
−
a
−
a
−
a
−
a
−
a
−
a
−
a
a
−
a
−
a
−
a
−
a
−
a
−
a
−
a
−
a
−
a
−
a
−
a
−
2.0 5.0
15.5 17.0 18.5
0.8 1.0 1.2
9.0 10.5 12.0
0.8 1.0 1.2
dB
−
Main contrast
control relative
characteristics1
∆VC1
VC2
−
−
−
a
−
a
−
a
−
a
−
a
−
−
−
−
Main contrast
control
characteristics2
b
SG1
b
SG5
64H
100
OUT
−
2.0 5.0
dB
−
Main contrast
control relative
characteristics2
∆VC2
VC3
−
−
−
−
−
Main contrast
control
characteristics3
b
SG1
b
SG5
14H
20
OUT
−
2.0 5.0
0.2 0.4 0.6 VP-P
Main contrast
control relative
characteristics3
∆VC3
VSC1
∆VSC1
VSC2
∆VSC2
VSC3
∆VSC3
−
−
−
−
−
0.8 1.0 1.2
15.8 17.3 18.8
0.8 1.0 1.2
11.5 13.0 14.5
0.8 1.0 1.2
−
dB
−
Sub contrast
control
characteristics1
b
SG1
b
SG5
FFH C8H C8H C8H
2.0 5.0
255 200 200 200
OUT
−
Sub contrast
control relative
characteristics1
−
−
−
−
− − − −
Sub contrast
control
characteristics2
b
SG1
b
SG5
FFH 64H 64H 64H
255 100 100 100
OUT
−
2.0 5.0
dB
−
Sub contrast
control relative
characteristics2
−
−
−
−
− − − −
Sub contrast
control
characteristics3
b
SG1
b
SG5
FFH 14H 14H 14H
255 20
OUT
−
2.0 5.0
1.4 1.7 2.0 VP-P
20
20
Sub contrast
control relative
characteristics3
−
−
−
−
−
−
−
−
0.8 1.0 1.2
−
3
MITSUBISHI ICs (Monitor)
PRELIMINARY
M52742SP
Notice:This is not a final specification.
Some parametric limits are subject to change.
BUS CONTROLLED 3-CHANNEL VIDEO PREAMP FOR CRT DISPLAY MONITOR
ELECTRICAL CHARACTERISTICS (cont.)
CTL
voltage
Input
BUS CTL (H)
Limits
Test
point
(s)
Symbol
VMSC
Parameter
Unit
0BH
INT
EXT
4,9,13
OSD
in
00H 01H 02H 03H 04H 05H 06H 07H 08H 09H
Main Sub Sub Sub OSD BLK D/A D/A D/A D/A
cont cont cont cont Adj Adj OUT OUT OUT OUT
1
OSD
BLK
7
SOG
in
2,6,11
RGB
in
19
27
16
UNI
in
15
ABL
30
Bri-
ght
CP in ReT
BLK
Min. Typ. Max.
1
2
3
1
2
3
4
Main/sub
contrast control
characteristics2
b
SG1
b
a
C8H C8H C8H C8H
200 200 200 200
OUT
a
a
a
a
2.0 5.0
3.4 4.0 4.6 VP-P
SG5
Main/sub contrast
control relative
characteristics2
∆VMSC
ABL1
−
OUT
−
−
−
a
−
a
−
−
a
−
a
−
−
−
a
−
a
−
−
a
−
a
−
−
a
−
a
−
−
−
−
−
−
−
0.8 1.0 1.2
4.1 4.9 5.7 VP-P
0.8 1.0 1.2
2.3 2.8 3.3 VP-P
−
b
SG1
b
SG5
ABL control
characteristics1
FFH FFH FFH FFH
255 255 255 255
2.0 4.0
ABL control
relative
characteristics1
∆ABL1
ABL2
−
−
−
−
−
b
SG1
b
SG5
ABL control
characteristics2
OUT
−
2.0 2.0
ABL control
relative
characteristics2
∆ABL2
−
−
−
−
0.8 1.0 1.2
3.3 3.7 4.1
−
Brightness
control
characteristics1
b
SG5
VB1
OUT
−
a
a
−
a
−
a
−
a
−
a
−
a
−
a
−
a
−
a
−
a
−
a
−
a
−
a
−
a
−
a
−
4.0 5.0
V
Brightness
control relative
characteristics1
∆VB1
VB2
−
a
−
a
−
−
−
−
-0.3
0
0.3
V
V
V
V
V
Brightness
control
characteristics2
b
SG5
OUT
−
2.0 5.0
1.5 1.8 2.1
Brightness
control relative
characteristics2
∆VB2
VB3
−
−
−
-0.3
0
0.3
Brightness
control
characteristics3
b
SG5
OUT
−
1.0 5.0
0.7 0.9 1.1
Brightness
control relative
characteristics3
∆VB3
−
−
−
-0.3
0
0.3
Frequency
characteristics1
(f=50MHz)
Va
ria
ble
b
SG3
a
5V
Vari
able
FC1
OUT
−
a
−
a
−
a
−
a
−
a
−
a
−
a
−
a
−
a
−
a
−
a
−
a
−
a
−
a
−
a
−
5.0
−
-2.0
-1.0
-3.0
-1.0
0
0
0
0
2.5
1.0
3.0
1.0
dB
dB
dB
dB
dB
dB
Frequency relative
characteristics1
(f=50MHz)
∆FC1
FC1’
−
−
−
−
Frequency
characteristics1
(f=150MHz)
Va
b
SG3
a
5V
Vari
able
FFH FFH FFH 00H 00H FFH FFH FFH FFH 00H
ria
OUT
−
5.0
255 255 255
0
0
255 255 255 255
0
ble
Frequency relative
characteristics1
(f=150MHz)
∆FC1’
FC2
−
−
Frequency
characteristics2
(f=150MHz)
b
SG3
a
5V
Vari
able
OUT
−
5.0
-3.0 3.0 5.0
Frequency relative
characteristics2
(f=150MHz)
∆FC2
−
−
−
−
-1.0
0
1.0
2bSG3
6a
11a
a
5V
Crosstalk 1
(f=50MHz)
Vari
able
OUT(29)
OUT(32)
FFH
255
C.T.1
C.T.1’
C.T.2
C.T.2’
C.T.3
C.T.3’
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
5.0
5.0
5.0
5.0
5.0
5.0
−
−
−
−
−
−
-25 -20
-15 -10
-25 -20
dB
dB
dB
2bSG3
6a
11a
a
5V
Crosstalk 1
(f=150MHz)
Vari
able
OUT(29)
OUT(32)
2a
6bSG3
11a
a
5V
Crosstalk 2
(f=50MHz)
Vari
able
OUT(29)
OUT(35)
2a
6bSG3
11a
a
5V
Crosstalk 2
(f=150MHz)
Vari
able
OUT(29)
OUT(35)
-15 -10 dB
-25 -20 dB
2a
6a
11bSG3
a
5V
Crosstalk 3
(f=50MHz)
Vari
able
OUT(32)
OUT(35)
2a
6a
11bSG3
a
5V
Crosstalk 3
(f=150MHz)
Vari
able
OUT(32)
OUT(35)
-15 -10
dB
4
MITSUBISHI ICs (Monitor)
PRELIMINARY
M52742SP
Notice:This is not a final specification.
Some parametric limits are subject to change.
BUS CONTROLLED 3-CHANNEL VIDEO PREAMP FOR CRT DISPLAY MONITOR
ELECTRICAL CHARACTERISTICS (cont.)
CTL
voltage
Input
BUS CTL (H)
Limits
Test
point
(s)
Symbol
Parameter
Unit
0BH
INT
EXT
4,9,13
OSD
in
00H 01H 02H 03H 04H 05H 06H 07H 08H 09H
Main Sub Sub Sub OSD BLK D/A D/A D/A D/A
cont cont cont cont Adj Adj OUT OUT OUT OUT
1
OSD
BLK
7
SOG
in
2,6,11
RGB
in
19
27
16
UNI
in
15
ABL
30
Bri-
ght
CP in ReT
BLK
Min. Typ. Max.
1
2
3
1
2
3
4
Pulse
characteristics1
(4VP-P)
Va
ria
ble
b
SG1
b
a
Vari
able
Tr
Tf
OUT
OUT
a
a
a
a
a
a
a
a
5.0
5.0
−
−
1.7
2.8
−
−
ns
ns
SG5
Pulse
characteristics2
(4VP-P)
Va
ria
ble
b
SG1
b
a
Vari
able
SG5
Clamp pulse
VthCP threshold
voltage
b
b
SG1
FFH
255
OUT
OUT
a
a
a
a
a
a
a
a
a
2.0 5.0
2.0 5.0
1.0 1.5 2.0
V
SG5
Variable
Clamp pulse
minimum
width
Pedestal voltage
temperature
characteristics1
b
b
SG1
WCP
a
a
0.2 0.5
−
µs
SG5
Variable
b
SG1
b
SG5
PDCH
PDCL
OUT
OUT
a
a
a
a
a
a
a
a
2.0 5.0
2.0 5.0
-0.3
-0.3
0
0
0.3
0.3
V
V
Pedestal voltage
temperature
characteristics2
b
SG1
b
SG5
a
a
b
SG5
OSD pulse
characteristics1
b
SG6
OTr
OUT
OUT
OUT
a
a
a
a
a
a
a
a
a
a
a
a
2.0 5.0
2.0 5.0
2.0 5.0
−
−
3.0 6.0
3.0 6.0
ns
ns
b
SG5
OSD pulse
characteristics2
b
SG6
08H
8
OTf
Oaj1
a
b
b
SG5
b
OSD adjust control
characteristics1
0FH
15
4.6 5.4 6.2 VP-P
0.8 1.0 1.2
2.8 3.3 3.8 VP-P
0.8 1.0 1.2
SG6 SG6
OSD adjust control
relative
characteristics1
∆Oaj1
Oaj2
−
OUT
−
−
a
−
a
−
−
−
−
−
a
−
a
−
−
a
−
a
−
−
a
−
a
−
−
−
−
−
b
SG5
b
b
OSD adjust control
characteristics2
08H
8
2.0 5.0
SG6 SG6
OSD adjust control
relative
characteristics2
∆Oaj2
OBLK
∆OBLK
−
−
−
−
−
−
−
b
SG5
OSD adjust control
characteristics3
b
SG6
00H
0
OUT
−
a
2.0 5.0
0
0.1 0.3 VP-P
0 0.15 VP-P
OSD adjust control
relative
characteristics3
−
−
−
−
−
−
-0.15
OSD input
VthOSD threshold
voltage
b
b
SG5
b
SG6
08H
8
OUT
OUT
a
a
a
a
a
a
a
2.0 5.0
2.0 5.0
2.2 2.7 3.2
V
V
SG6
Variable
OSD BLK input
threshold
voltage
b
b
SG1
b
SG5
00H
0
VthBLK
a
2.2 2.7 3.2
SG6
Variable
Retrace BLK
characteristics1
b
b
0FH
15
HBLK1
HBLK2
HBLK3
OUT
OUT
OUT
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
2.0 5.0
2.0 5.0
2.0 5.0
1.7 2.0 2.3
0.7 1.0 1.3
0.1 0.4 0.7
V
V
V
SG7
SG5
Retrace BLK
characteristics2
b
SG5
b
SG7
06H
6
Retrace BLK
characteristics3
b
SG5
b
SG7
00H
0
Retrace BLK
input threshold
voltage
b
b
08H
8
VthRET
OUT
a
a
a
a
a
a
a
b
a
a
2.0 5.0
2.0 5.0
1.0 1.5 2.0
V
SG7
SG5
Variable
SOG input
SS-NV maximum
noize voltage
SonG IN
Sync OUT
a
a
a
a
−
−
0.02 VP-P
SG4
Variable
SOG
SS-SV minimum
b
SonG IN
Sync OUT
a
a
a
a
2.0 5.0
0.2 0.3
−
VP-P
SG4
Variable
input voltage
Sync output
hi level
b
Sync OUT
Sync OUT
Sync OUT
VSH
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
2.0 5.0
2.0 5.0
2.0 5.0
4.5 4.9 5.0
V
V
SG4
Sync output
lo level
b
SG4
VSL
0
0.3 0.6
60 90
Sync output
delay time1
b
SG4
TDS-F
0
ns
5
MITSUBISHI ICs (Monitor)
PRELIMINARY
M52742SP
Notice:This is not a final specification.
Some parametric limits are subject to change.
BUS CONTROLLED 3-CHANNEL VIDEO PREAMP FOR CRT DISPLAY MONITOR
ELECTRICAL CHARACTERISTICS (cont.)
CTL
voltage
Input
BUS CTL (H)
Limits
Test
point
(s)
Symbol
Parameter
Unit
ns
0BH
INT
EXT
4,9,13
OSD
in
00H 01H 02H 03H 04H 05H 06H 07H 08H 09H
Main Sub Sub Sub OSD BLK D/A D/A D/A D/A
cont cont cont cont Adj Adj OUT OUT OUT OUT
1
OSD
BLK
7
SOG
in
2,6,11
RGB
in
19
27
16
UNI
in
15
ABL
30
Bri-
ght
CP in ReT
BLK
Min. Typ. Max.
1
2
3
1
2
3
4
Sync output
delay time2
b
SG4
Sync OUT
TDS-R
VOH
VOL
IAO
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
2.0 5.0
2.0 5.0
2.0 5.0
2.0 5.0
2.0 5.0
0
60 90
D/A H output
voltage
D/A
OUT
FFH FFH FFH FFH 00H 00H FFH FFH FFH FFH 00H
a
a
a
a
a
a
a
a
4.5 5.0 5.5 VDC
255 255 255 255
0
0
255 255 255 255
0
D/A L output
voltage
D/A
OUT
00H 00H 00H 00H
0
-1.0
-1.0
-0.8
-0.8
7
0.5 1.0 VDC
0
0
0
0
Vari Vari Vari Vari
abl abl abl abl
D/A output
D/A
−
−
0.4 mA
1.0 LSB
current range OUT
e
e
e
e
Vari Vari Vari Vari
abl abl abl abl
D/A
nonlinearity
D/A
OUT
DNL
∆Tr
e
e
e
e
Vari
abl
e
Relative pulse
characteristics1
b
SG1
b
SG5
Vari
5.0
FFH FFH FFH FFH
255 255 255 255
OUT
OUT
OUT
OUT
0
0
0.8
0.8
ns
ns
%
%
able
Vari
abl
e
Relative pulse
characteristics2
b
SG1
b
SG5
Vari
5.0
∆Tf
able
b
SG6
2.5V
Uniformity
characteristics1
b
SG1
b
SG5
C8H C8H C8H C8H
200 200 200 200
UNI1
UNI2
2.0 5.0
2.0 5.0
10 13
6.5
b
Uniformity
characteristics2
b
SG1
b
SG5
SG6
1.25V
3.5
5
ELECTRICAL CHARACTERISTICS TEST METHOD
Gv Maximum gain
Input SG1, and read the amplitude output at OUT (29, 32, 35). The
amplitude is called VOUT (29, 32, 35). Maximum gain GV is
calculated by the equation below:
ICC1 Circuit current1
Measuring conditions are as listed in supplementary Table.
Mesured with a current meter at test point IA.
VOUT
0.7
(dB)
GV=20Log
ICC2 Circuit current2
∆Gv Relative maximum gain
Measureing conditions are as listed in supplemtary Table.
Relative maximum gain ∆GV is calculated by the equation bellow:
∆GV= VOUT (29)/VOUT (32),
Measured with a current meter at test point IB.
Vomax Output dynamic range
Decrease V30 gradually, and measure the voltage when the
VOUT (32)/VOUT (35),
VOUT (35)/VOUT (29)
waveform output is distorted. The voltage is called VOL.
Next, increase V30 gradually, and measure the voltage when the
top of waveform output is distorted. The voltage is called VOH.
Voltage Vomax is calculated by the equation below:
VC1 Main contrast control characteristics1
Measureing the amplitude output at OUT (29, 32, 35). The
measuredvalue is called VOUT (29, 32, 35). Main contrast control
characterics VC1 is calculated by the equation bellow:
VOUT
Vomax = VOH-VOL
(V)
(dB)
VC1=20Log
0.7
VOH
∆VC1 Main contrast control relative characteristics1
Relative characteristics ∆VC1 is calculated by the equation bellow:
∆VC1=VOUT (29)/VOUT (32),
5.0
Waveform output
VOUT (32)/VOUT (35),
VOL
0.0
VOUT (35)/VOUT (29)
VC2 Main contrast control characteristics2
Vimax Maximum input
Measuring condition and procedure are the same as described in
Increase the input signal (SG2) amplitude gradually, starting from
VC1.
700mVP-P. Measure the amplitude of the input signal when the
output signal starts becoming distorted.
∆VC2 Main contrast control relative characteristics2
Measuring condition and procedure are the same as described in
∆VC1.
6
MITSUBISHI ICs (Monitor)
PRELIMINARY
M52742SP
Notice:This is not a final specification.
Some parametric limits are subject to change.
BUS CONTROLLED 3-CHANNEL VIDEO PREAMP FOR CRT DISPLAY MONITOR
VC3 Main contrast control characteristics3
ABL1 ABL control characteristics1
Measuring condition and procedure are the same as described in
VC1.
Measure the amplitude output at OUT (29, 32, 35). The measured
value is called VOUT (29, 32, 35), and is ttreated as ABL1.
∆VC3 Main contrast control relative characteristics3
Measuring condition and procedure are the same as described in
∆VC1.
∆ABL1 ABL control relative characteristics1
Relative characteristics ∆ABL1 is calculated by the equation below:
∆ABL1= VOUT (29)/VOUT (32),
VOUT (32)/VOUT (35),
VOUT (35)/VOUT (29)
VSC1 Sub contrast control characteristics1
Measur the amplitude output at OUT (29, 32, 35). The measured
value is called VOUT (29, 32, 35). Sub contrast control
characteristics VSC1 is calculated by the equation below:
ABL2 ABL control characteristics2
Measuring condition and procedure are the same as described in
ABL1.
VOUT
0.7
(dB)
VSC1=20Log
∆ABL2 ABL control relative characteristics2
Measuring condition and procedure are the same as described in
∆ABL1.
∆VSC1 Sub contrast control relative characteristics1
Relative characteristics ∆VSC1 is calculated by the equation below:
∆VSC1= VOUT (29)/VOUT (32),
VOUT (32)/VOUT (35),
VB1 Brightness control characteristics1
VOUT (35)/VOUT (29).
Measure the DC voltage at OUT (29, 32, 35) with a voltmeter. The
measured value is called VOUT (29, 32, 35), and is ttreated as VB1.
VSC2 Sub contrast control characteristics2
Measuring condition and procedure are the same as described in
∆VB1 Brightness control relative characteristics1
Relative characteristics ∆VB1 is calculated by the difference in the
output between the channels.
VSC1.
∆VSC2 Sub contrast control relative characteristics2
∆VB1= VOUT (29)/VOUT (32),
Measuring condition and procedure are the same as described in
VOUT (32)/VOUT (35),
∆VSC1.
VOUT (35)/VOUT (29)
VSC3 Sub contrast control characteristics3
Measuring condition and procedure are the same as described in
VB2 Brightness control characteristics2
VSC1.
Measuring condition and procedure are the same as described in
VB1.
∆VSC3 Sub contrast control relative characteristics3
Measuring condition and procedure are the same as described in
∆VSC1.
∆VB2 Brightness control relative characteristics2
Measuring condition and procedure are the same as described in
∆VB1.
VMSC Main/sub contrast control characteristics2
Measure the amplitude output at OUT (29, 32, 35). The measured
value is called VOUT (29, 32, 35). Main/Sub contrast control
characteristics VMSC1 is calculated by the equation below:
VB3 Brightness control characteristics3
Measuring condition and procedure are the same as described in
VB1.
VOUT
0.7
(dB)
VMSC1=20Log
∆VB3 Brightness control relative characteristics3
Measuring condition and procedure are the same as described in
∆VB1.
∆VMSC Main/sub contrast control relative characteristics2
Relative characteristics ∆VMSC1 is calculated by the equation
below:
∆VMSC1= VOUT (29)/VOUT (32),
VOUT (32)/VOUT (35),
VOUT (35)/VOUT (29)
7
MITSUBISHI ICs (Monitor)
PRELIMINARY
M52742SP
Notice:This is not a final specification.
Some parametric limits are subject to change.
BUS CONTROLLED 3-CHANNEL VIDEO PREAMP FOR CRT DISPLAY MONITOR
FC1 Frequency characteristics1 (f=50MHz)
C.T.2 Crosstalk2 (f=50MHz)
First, SG3 to 1MHz is as input signal. Input a resister that is about
2kΩ to offer the voltage at input pins (2, 6, 11) in order that the bot-
tom of input signal is 2.5V. Control the main contrast in order that
the amplitude of sine wave output is 4.0VP-P. Control the brightness
in order that the bottom of sine wave output is 2.0VP-P. By the same
way, measure the output amplitude when SG3 to 50MHz is as input
signal. The measured value is called VOUT (29, 32, 35). Frequency
characteristics FC1 (29, 32, 35) is calculated by the equation below:
Input SG3 (50MHz) to pin6 only, and then measure the waveform
amplitude output at OUT (29, 32, 35). The measured value is called
VOUT (29, 32, 35). Crosstalk C.T.2 is calculated by the equation
below:
VOUT (29, 32)
VOUT (35)
C.T.2=20 log
(dB)
C.T.2' Crosstalk2 (f=150MHz)
VOUT VP-P
Measuring condition and procedure are the same as described in
C.T.2, expect SG3 to 150MHz.
FC1=20log
(dB)
Output amplitude when inputed SG3 (1MHz):4VP-P
∆FC1 Frequency relative characteristics1 (f=50MHz)
C.T.3 Crosstalk3 (f=50MHz)
Relative characteristics ∆FC1 is calculated by the difference in the
Input SG3 (50MHz) to pin11 only, and then measure the waveform
output between the channels.
amplitude output at OUT (29, 32, 35). The measured value is called
VOUT (29, 32, 35). Crosstalk C.T.3 is calculated by the equation
below:
FC1' Frequency characteristics1 (f=150MHz)
Measuring condition and procedure are the same as described in
VOUT (29, 32)
VOUT (35)
C.T.3=20 log
(dB)
table, expect SG3 to 150MHz.
∆FC1' Frequency relative characteristics1 (f=150MHz)
C.T.3' Crosstalk3 (f=150MHz)
Relative characteristics ∆FC1' is calculated by the difference in the
Measuring condition and procedure are the same as described in
C.T.3, expect SG3 to 150MHz.
output between the channels.
FC2 Frequency characteristics2 (f=150MHz)
Tr Pulse characteristics1 (4VP-P)
SG3 to 1MHz is as input signal. Control the main contrast in order
Control the main contrast (00H) in order that the amplitude of output
that the amplitude of sine wave output is 1.0VP-P. By the same way,
measure the output amplitude when SG3 to 150MHz is as input
signal.
signal is 4.0VP-P.
Control the brightness (V30) in order that the Black level of output
signal is 2.0V.
The measured value is called VOUT (29, 32, 35). Frequency
characteristics FC2 (29, 32, 35) is calculated by the equation below:
Measure the time needed for the input pulse to rise from 10% to 90
% (Tr1) and for the output pulse to rise from 10% to 90% (Tr2) with
an active prove.
VOUT VP-P
FC1=20log
(dB)
Output amplitude when inputed SG3 (1MHz):4VP-P
Pulse characteristics TR is calculated by the equations below :
TR= [(Tr2)2-(Tr1)2]
∆FC2 Frequency relative characteristics2 (f=150MHz)
Relative characteristics ∆FC2 is calculated by the difference in the
∆Tr Relative pulse characteristics1
output between the channels.
Relative characteristics ∆Tr is calculated by the difference in the
output between the channels.
C.T.1 Crosstalk1 (f=50MHz)
Input SG3 (50MHz) to pin2 only, and then measure the waveform
Tf Pulse characteristics2 (4VP-P)
amplitude output at OUT (29, 32, 35). The measured value is called
VOUT (29, 32, 35). Crosstalk C.T.1 is calculated by the equation
below:
Measure the time needed for the input pulseto fall from 90% to 10%
(Tf1) and for the output pulse to fall from 90% to 10% (Tf2) with an
active prove.
VOUT (29, 32)
C.T.1=20 log
(dB)
Pulse characteristics TF is calculated by the equations below :
VOUT (35)
TR= [(Tf2)2-(Tf1)2]
C.T.1' Crosstalk1 (f=150MHz)
Measuring condition and procedure are the same as described in
C.T.1, expect SG3 to 150MHz.
8
MITSUBISHI ICs (Monitor)
PRELIMINARY
M52742SP
Notice:This is not a final specification.
Some parametric limits are subject to change.
BUS CONTROLLED 3-CHANNEL VIDEO PREAMP FOR CRT DISPLAY MONITOR
∆Oaj1 OSD adjust control relative characteristics1
∆Tf Relative pulse characteristics2
Relative characteristics ∆Oaj1 is calculated by the equation below:
Relative characteristics ∆Tf is calculated by the difference in the
∆Oaj1=VOUT (29)/VOUT (32),
VOUT (32)/VOUT (35),
output between the channels.
100%
90%
VOUT (35)/VOUT (29)
Oaj2 OSD adjust control characteristics2
Measuring condition and procedure are the same as described in
10%
Oaj1.
0%
Tr1 or Tr2
Tf1 or Tf2
∆Oaj2 OSD adjust control relative characteristics2
Measuring condition and procedure are the same as described in
VthCP Clamp pulse threshold voltage
∆Oaj1.
Turn down the SG5 input level gradually from 5.0VP-P, monitoring
the waveform output.
OBLK OSD adjust control characteristics3
Measuring condition and procedure are the same as described in
Measure the top level of input pulse when the output pedestal
voltage turn decrease with unstable.
Oaj1.
∆OBLK OSD adjust control relative characteristics3
WCP Clamp pulse minimum width
Measuring condition and procedure are the same as described in
Decrease the SG5 pulse width gradually from 0.5µs, monitoring the
output. Measure the SG5 pulse width (a point of 1.5V) when the
output pedestal voltage turn decrease with unstable.
∆Oaj1.
VthOSD OSD input threshold voltage
Reduce the SG6 input level gradually, monitoring output. Measure
the SG6 level when the output reaches 0V. The measured value is
called VthOSD.
PDCH Pedestal voltage temperature characteristics1
Measure the pedestal voltage at 25°C. The measured value is
called PDC1.
Measure the pedestal voltage at temperature of -20°C. The
measured value is called PDC2.
VthBLK OSD BLK input threshold voltage
Confirm that output signal is being blanked by the SG6 at the time.
Monitoring to output signal, decreasing the level of SG6. Measure
the top level of SG6 when the blanking period is disappeared. The
measured value is called VthBLK.
Pedestal voltage temperature characteristics 1 is calculated by the
equation below:
PDCH=PDC1-PDC2
PDCL Pedestal voltage temperature characteristics2
HBLK1 Retrace BLK characteristics1
Measure the pedestal voltage at 25°C. The measured value is
Measure the amplitude output is blanked by the SG7 at OUT (29,
32, 35). The measured value is called VOUT (29, 32, 35), and is
treated as HBLK1.
called PDC1.
Measure the pedestal voltage at temperature of 75°C. The
measured value is called PDC3.
Pedestal voltage temperature characteristics 2 is calculated by the
equation below:
HBLK2 Retrace BLK characteristics2
Measure the amplitude output is blanked by the SG7 at OUT (29,
32, 35). The measured value is called VOUT (29, 32, 35), and is
treated as HBLK2.
PDCL=PDC1-PDC3
OTr OSD pulse characteristics1
Measure the time needed for the output pulse to rise from 10% to
HBLK3 Retrace BLK characteristics3
90% (OTR) with an active prove.
Measure the amplitude output is blanked by the SG7 at OUT (29,
32, 35). The measured value is called VOUT (29, 32, 35), and is
treated as HBLK3.
OTf OSD pulse characteristics2
Measure the time needed for the output pulse to fall from 90% to
10% (OTF) with an active prove.
VthRET Retrace BLK input threshold voltage
Confirm that output signal is being blanked by the SG7 at the time.
Monitoring to output signal, decreasing the level of SG7. Measure
the top level of SG7 when the blanking period is disappeared. The
measured value is called VthRET.
Oaj1 OSD adjust control characteristics1
Measure the amplitude output at OUT (29, 32, 35). The measured
value is called VOUT (29,32,35), and is treated as Oaj1.
9
MITSUBISHI ICs (Monitor)
PRELIMINARY
M52742SP
Notice:This is not a final specification.
Some parametric limits are subject to change.
BUS CONTROLLED 3-CHANNEL VIDEO PREAMP FOR CRT DISPLAY MONITOR
SS-NV SOG input maximum noize voltage
VOH D/A H output voltage
The sync's amplitude of SG4 be changed all white into all black,
increase from 0VP-P to 0.02VP-P. No pulse output permitted.
Measure the DC voltage at D/AOUT. The measured value is
ttreated as VOH.
SS-SV SOG minimum input voltage
VOL D/A L output voltage
The sync's amplitude of SG4 be changed all white or all black,
decrease from 0.3VP-P to 0.2VP-P. Confirm no malfunction produced
by noise.
Measure the DC voltage at D/AOUT. The measured value is
ttreated as VOL.
IAO D/A output current range
Electric current flow from the output of D/AOUT must be less than
VSH Sync output hi level
1.0mA.
Measure the high voltage at SyncOUT. The measured value is
treated as VSH.
Electric current flow in the output of D/AOUT must be less than
0.4mA.
VSL Sync output lo level
Measure the low voltage at SyncOUT. The measured value is
treated as VSL.
DNL D/A nonlinearity
The difference of differential non-linearity of D/AOUT must be less
than ±1.0LSB.
TDS-F Sync output delay time1
SyncOUT becomes High with sync part of SG4.
UNI1 Uniformity characteristics1
Measure the time needed for the front edge of SG4 sync to fall from
50% and for SyncOUT to rise from 50% with an active prove. The
measured value is treated as TDS-F, less than 90nsec.
UNI2 Uniformity characteristics2
VuniA is amplitude output at OUT (29, 32, 35), when SG6 is low
voltage. VuniB is amplitude output at OUT (29, 32, 35), when SG6
is high voltage.
moduration ratio UNI (UNI2) is calculated by the equation below;
UNI1 (UNI2)=100 (VuniB/VuniA-1) (%)
TDS-R Sync output delay time2
Measure the time needed for the rear edge of SG4 sync to rise
from 50% and for SyncOUT to fall from 50% with an active prove.
The measured value is treated as TDS-R, less than 90nsec.
VuniB
OUT
SG6
VuniA
Pedestal
voltage
SG4
Pedestal voltage
sync (50%)
TDS-F
(50%)
5VP-P (2.5VP-P)
SyncOUT
TDS-R
10
MITSUBISHI ICs (Monitor)
PRELIMINARY
M52742SP
Notice:This is not a final specification.
Some parametric limits are subject to change.
BUS CONTROLLED 3-CHANNEL VIDEO PREAMP FOR CRT DISPLAY MONITOR
I2C-BUS PROTOCOL
(1) Slave address
D7
1
D6
D5
0
D4
1
D3
1
D2
1
D1
0
R/W
0
1
=DCH
(2) Slave receiver format
S
SLAVE ADDRESS
SUB ADDRESS
DATA BYTE
A
A
A
P
START condition
acknowledg
STOP condition
(3) Sub address byte and data byte format
Function
Data byte (top:byte format under:start condition)
sub
add.
bit
8
8
8
8
4
4
8
8
8
8
1
D7
A07
0
D6
A06
1
D5
A05
0
D4
A04
0
D3
A03
0
D2
A02
0
D1
A01
0
D0
A00
0
Main contrast
00H
A17
1
A16
0
A15
0
A14
0
A13
0
A12
0
A11
0
A10
0
Sub contrast R
01H
02H
03H
04H
05H
06H
07H
08H
09H
0BH
A27
1
A26
0
A25
0
A24
0
A23
0
A22
0
A21
0
A20
0
Sub contrast G
A37
1
A36
0
A35
0
A34
0
A33
0
A32
0
A31
0
A30
0
Sub contrast B
−
−
−
−
A43
1
A42
0
A41
0
A40
0
OSD level
0
0
0
0
−
−
−
−
A53
1
A52
0
A51
0
A50
0
RE-BLK adjust
0
0
0
0
A67
1
A66
0
A65
0
A64
0
A63
0
A62
0
A61
0
A60
0
D/A OUT1
A77
1
A76
0
A75
0
A74
0
A73
0
A72
0
A71
0
A70
0
D/A OUT2
A87
1
A86
0
A85
0
A84
0
A83
0
A82
0
A81
0
A80
0
D/A OUT3
A97
1
A96
0
A95
0
A94
0
A93
0
A92
0
A91
0
A90
0
D/A OUT4
−
−
−
−
−
−
−
AB0
0
Pedestal clamp INT/EXT SW
0
0
0
0
0
0
0
Notes) pedestal level INT/EXT SW
0→INT
1→EXT
11
MITSUBISHI ICs (Monitor)
PRELIMINARY
M52742SP
Notice:This is not a final specification.
Some parametric limits are subject to change.
BUS CONTROLLED 3-CHANNEL VIDEO PREAMP FOR CRT DISPLAY MONITOR
TIMING REQUIREMENT OF I2C
Symbol
Parameter
Min.
-0.5
3.0
0
Max.
1.5
5.5
100
−
Unit
V
VIL
Input voltage LOW
Input voltage HIGH
SCL clock frequency
VIH
V
fSCL
kHz
µs
µs
µs
µs
µs
µs
ns
ns
ns
µs
tBUF
Time the bus must be free before a new transmission can start
Hold time start condition. After this period the first clock pulse is generated
The LOW period of the clock
4.7
4.0
4.7
4.0
4.7
0
tHD:STA
tLOW
tHIGH
tSU:STA
tHD:DAT
tSU:DAT
tr
−
−
The HIGH period of the clock
−
Set up time for start condition (Only rerevant for a repeated start condition)
Hold time for I2C devices
−
−
Set-up time DATA
250
−
−
Rise time of both SDA and SCL
1000
300
−
tf
Fall time of both SDA and SCL
−
tSU:STO
Set-up time for stop condition
4.0
TIMING DIAGRAM
tBUF
tr, tf
VIH
SDA
VIL
tSU:STA
tSU:STO
tHD:STA
tSU:DAT
tHD:DAT
VIH
SCL
VIL
tLOW
tHIGH
S
S
P
S
12
MITSUBISHI ICs (Monitor)
PRELIMINARY
M52742SP
Notice:This is not a final specification.
Some parametric limits are subject to change.
BUS CONTROLLED 3-CHANNEL VIDEO PREAMP FOR CRT DISPLAY MONITOR
INPUT SIGNAL
SG No.
Signals
Pulse with amplitude of 0.7VP-P (f=30kHz). Video width of 25µs. (75%)
33µs
SG1
Video signal
(all white)
8µs
0.7VP-P
SG2
Video signal
(step wave)
0.7VP-P
(Amplitude is partially variable.)
SG3
Sine wave
(for freq. char.)
Sine wave amplitude of 0.7VP-P.
f=1MHz, 50MHz, 150MHz (variable)
Video width of 25µs. (75%)
SG4
all white or all black
variable.
0.7VP-P
Video signal
(all white,
all black)
Sync’s amplitude
0.3VP-P
3µs
is variable.
Pulse width and amplitude are variable.
0.5µs
SG5
Clamp
pulse
5VTTL
SG6
OSD pulse
Amplitude is partially variable.
5VTTL
5µs
SG7
BLK pulse
5VTTL
Amplitude is partially variable.
5µs
) f=30kHz
13
MITSUBISHI ICs (Monitor)
PRELIMINARY
M52742SP
Notice:This is not a final specification.
Some parametric limits are subject to change.
BUS CONTROLLED 3-CHANNEL VIDEO PREAMP FOR CRT DISPLAY MONITOR
TEST CIRCUIT
D/A
D/A
D/A
D/A
SG7
a
SG5
SDA
SCL
OUT (35)
OUT (32)
OUT (29)
OUT1 OUT2 OUT3 OUT4
C/P IN
V30
0 to 5V
100
b
b
a
470
470
470
SW27
SW19
100µH
36
35
34
f/b
31
f/b
29
20
scl
19
23
22
21
33
32
30
brt
27
blk
26
25
24
28
f/b
12V
out
gnd
out
out
dac
dac
dac
dac
gnd
sda
c/p
M52742SP
blk
1
R
2
12V
3
osd
4
gnd
5
G
6
SonG 12V
osd
9
gnd
10
B
12V
12
osd
13
gnd
14
abl
15
UNI
16
5V
17
sync
18
7
8
11
47µ
100k
IN (2)
IN (6) SONG
IN
0.01µ
3.3µ
IN (11)
0.01µ
3.3µ
SYNC
OUT
0.01µ
3.3µ
1µ
V15
0 to 5V
1k
SW1 SW2
SW4
a
SW6
a
SW7
a
b
SW9
a
SW11
a
SW13
SW16
b
a
a
a
a
b
b
b
b
b
b
b
A
IB
IA
5V
SG6
A
47µ
12V
SG6
SG1
SG2
SG3
SG4
: MEASURE POINT
Condenser : 0.01µF (unless otherwise specified.)
Units Resistance : Ω
Capacitance : F
14
MITSUBISHI ICs (Monitor)
PRELIMINARY
M52742SP
Notice:This is not a final specification.
Some parametric limits are subject to change.
BUS CONTROLLED 3-CHANNEL VIDEO PREAMP FOR CRT DISPLAY MONITOR
TYPICAL CHARACTERISTICS
THERMAL DERATING
MAIN CONTRAST CONTROL CHARACTERISTICS
2800
6
2403
2400
5
4
3
2
2000
1600
1200
800
400
0
1442
1
Sub contrast: Max
0
00H
-20
0
25
50
75
100 125 150
FFH
AMBIENT TEMPERATURE Ta (°C)
MAIN CONTRAST CONTROL DATA
SUB CONTRAST CONTROL CHARACTERISTICS
BRIGHTNESS CONTROL CHARACTERISTICS
6
6
5
4
3
2
5
4
3
2
1
0
1
Main contrast: Max
0
00H
FFH
0
2
4
SUB CONTRAST CONTROL DATA
BRIGHTNESS CONTROL VOLTAGE (VDC)
OSD ADJUST CONTROL CHARACTERISTICS
ABL CHARACTERISTICS
6
6
5
4
3
2
1
0
5
4
3
2
1
0
Main contrast: Max
Sub contrast : Max
0H
FH
0
5
OSD ADJUST CONTROL DATA
ABL CONTROL VOLTAGE (VDC)
15
MITSUBISHI ICs (Monitor)
PRELIMINARY
M52742SP
Notice:This is not a final specification.
Some parametric limits are subject to change.
BUS CONTROLLED 3-CHANNEL VIDEO PREAMP FOR CRT DISPLAY MONITOR
SYNC ON GREEN INPUT MIN. PULSE WIDTH
UNIFORMITY CHARACTERISTICS
12
12
10
8
(Video duty=75%)
10
8
Sync separate
normal operating range
6
4
2
6
4
2
7
100k
0
0
1µ
0
0.5
0
0.5
1.0
1.5
2.0
2.5
INPUT SYNC AMPLITUDE (VP-P)
INPUT AMPLITUDE (VP-P)
IN
16
MITSUBISHI ICs (Monitor)
PRELIMINARY
M52742SP
Notice:This is not a final specification.
Some parametric limits are subject to change.
BUS CONTROLLED 3-CHANNEL VIDEO PREAMP FOR CRT DISPLAY MONITOR
APPLICATION EXAMPLE
CRT
110V
Cut Off Adj
DAC OUT×4
5VTTL
BLK IN
(for retrace)
470
470
470
SDA
0 to 5V
0.01µ
30 29
SCL
Clamp pulse
IN
100
36
0.01µ 0.01µ
0.01µ 0.01µ
100µH
35
34
33
32
31
28
27
26
25
24
23
22
21
20
19
M52742SP
1
2
3
4
5
6
7
8
9
10
0.01µ
11
12
13
14
15
16
17
18
0.01µ
0.01µ
100k
0.01µ
1µ
ABL IN
0 to 5V
47µ
3.3µ
47µ
3.3µ
47µ
1k
Sync
Sep
OUT
0.01µ
0.01µ
0.01µ
3.3µ
5VTTL
75
75
75
Uniformity
IN
5VTTL
5VTTL
OSD IN (B)
OSD IN (G)
OSD IN (R)
5VTTL
BLK IN
(for OSD)
47µ
0.01µ
12V
5V
INPUT
(R)
INPUT
(G)
SONG
INPUT
INPUT
(B)
•FEED BACK IS
INTERNAL FEED BACK
Units Resistance : Ω
Capacitance : F
Circuit example of pin6 and pin7 same signal input
17
MITSUBISHI ICs (Monitor)
PRELIMINARY
M52742SP
Notice:This is not a final specification.
Some parametric limits are subject to change.
BUS CONTROLLED 3-CHANNEL VIDEO PREAMP FOR CRT DISPLAY MONITOR
DESCRIPTION OF PIN
Pin No.
Name
DC voltage (V )
Peripheral circuit of pins
Description of function
R
G
Input pulses
3.7 to 5V
1
1
OSD BLK IN
−
B
1.7V
maximum
Connected to GND if not
used.
0.8mA
2.7V
2k
2k
Clamped to about 2.5V
due to clamp pulses
from pin 19.
2
6
11
INPUT (R)
INPUT (G)
INPUT (R)
2.5
2
Input at low impedance.
2.5V
CP
0.3mA
3
8
12
VCC1 (R)
VCC1 (G)
VCC1 (B)
Apply equivalent
voltage to 3 channels.
12
−
Input pulses
3.7 to 5V
1k
4
9
13
OSD IN (R)
OSD IN (G)
OSD IN (B)
−
1.7V
maximum
4
Connected to GND if not
used.
2.7V
0.5mA
5
GND 1 (R)
GND 1 (G)
GND 1 (B)
GND (5V)
GND 2
10
14
22
33
GND
−
SYNC ON GREEN
input pin for sync
separation.
Sync is negative.
input signal at Pin7,
compare with the
reference voltage of
internal circuit in order to
separate sync signal.
When not used, set to
OPEN.
INPUT
(S on G)
500
7
When open≈2.5V
1k
3.2V
7
18
MITSUBISHI ICs (Monitor)
PRELIMINARY
M52742SP
Notice:This is not a final specification.
Some parametric limits are subject to change.
BUS CONTROLLED 3-CHANNEL VIDEO PREAMP FOR CRT DISPLAY MONITOR
DESCRIPTION OF PIN (cont.)
Pin No.
Name
DC voltage (V )
When open 2.5V
Peripheral circuit of pins
Description of function
2.5V
20k
30k
ABL (Automatic Beam
Limitter) input pin.
Recommended voltage
range is 0 to 5V.
When ABL function is not
used, set to 5V.
15
ABL IN
1.2k
1.2k
0.5mA
15
Uniformity input pin.
Recommended
amplitude range is 0 to
5VP-P.
200
16
Uniformity IN
5.75
20k
5k
7.25V
16
17
18
VCC (5V)
5
−
18
Sync signal output pin,
Being of open collector
output type.
S on G Sep
OUT
−
41k
Input pulses
2.5 to 5V
Clamp Pulse
IN
19
−
0.5V
maximum
19
Input at low impedance.
2.2V
0.15mA
50k
SCL of I2C BUS
(Serial clock line)
VTH=2.3V
20
SCL
−
20
2k
3V
19
MITSUBISHI ICs (Monitor)
PRELIMINARY
M52742SP
Notice:This is not a final specification.
Some parametric limits are subject to change.
BUS CONTROLLED 3-CHANNEL VIDEO PREAMP FOR CRT DISPLAY MONITOR
DESCRIPTION OF PIN (cont.)
Pin No.
Name
DC voltage (V )
Peripheral circuit of pins
50k
Description of function
SDA of I2C BUS
(Serial data line)
VTH=2.3V
21
SDA
−
21
2k
3V
23
24
25
26
D/A output pin.
Output voltage range is
0 to 5V, Max output
current is 0.4mA.
D/A OUT
−
23
Input pulses
2.5 to 5V
50k
R
G
B
Retrace BLK
IN
27
−
0.5V
27
maximum
2.25V
Connected to GND if not
used.
35k
28
31
34
EXT Feed
Back (B)
EXT Feed
Back (G)
EXT Feed
Back (R)
Variable
28
A resistor is needed on
the GND side.
Set discretionally to
maximum 15mA,
36
29
32
35
OUTPUT (B)
OUTPUT (G)
OUTPUT (R)
Variable
50
depending on the
required driving capacity.
50
29
Used to supply power to
output emitter follower
only.
12
36
VCC2
Impressed
20
MITSUBISHI ICs (Monitor)
PRELIMINARY
M52742SP
Notice:This is not a final specification.
Some parametric limits are subject to change.
BUS CONTROLLED 3-CHANNEL VIDEO PREAMP FOR CRT DISPLAY MONITOR
DESCRIPTION OF PIN (cont.)
Pin No.
Name
DC voltage (V )
Peripheral circuit of pins
35k
Description of function
It is recommended that
the IC be used between
pedestal voltage 2V and
3V.
Main
Brightness
30
−
30
APPLICATION METHOD FOR M52742SP
NOTICE OF APPLICATION
Make the nearest distance between output pin and pull down
resister.
CLAMP PULSE INPUT
Clamp pulse width is recommended
Recommended pedestal voltage of IC output signal is 2V.
above 15kHz, 1.0µsec
above 30kHz, 0.5µsec
above 64kHz, 0.3µsec.
The clamp pulse circuit in ordinary set is a long round about way,
and beside high voltage, sometimes connected to external terminal,
it is very easy affected by large surge.
Therefore, the Fig. shown right is recommended.
19
EXT-FEED BACK
In case of application circuit example of lower figure, Set up R1, R2
which seems that the black level of the signal feedbacked from
Power AMP is 1V, when the bottom of output signal is 1V.
Power Amp
MAIN BRIGHTNESS
DC:1 to 5V
Power Amp OUT
Pre Amp
INPUT R
R OUT PUT
Black level 1 to 5V
R1
R Feed back
Black level 1 to 5V
R2
EXT-FEED BACK APPLICATION CIRCUIT
21
相关型号:
©2020 ICPDF网 联系我们和版权申明