MIC47050YMT-TR [MICROCHIP]
暂无描述;MIC47050
500mA ULDO™ with Low Input
and Low Output Voltage
General Description
Features
The MIC47050 is a high-speed, ultra-low dropout, dual-
supply NMOS ULDO™ designed to take advantage of
point-of-load applications that use multiple supply rails to
generate a low-voltage, high-current power supply. The
MIC47050 can source 500mA of output current while only
requiring a 1µF ceramic output capacitor for stability. A
1.5% output voltage accuracy, low dropout voltage (44mV
@ 500mA), and low ground current makes this device
ideally suited for mobile and point-of-load applications.
Voltage range
– Input Voltage: 1.0V to 3.6V
– Bias Voltage: 2.3V to 5.5V
0.4V to 2.0V output voltage range
Low dropout voltage of 44mV at 500mA
±1.5% initial output voltage accuracy
High bandwidth – very fast transient response
Stable with a 1µF ceramic output capacitor
Logic level enable input
The MIC47050 has an NMOS output stage offering very
low output impedance. The NMOS output stage makes for
a unique ability to respond very quickly to sudden load
changes such as that required by a microprocessor, DSP
or FPGA. The MIC47050 consumes little quiescent current
and therefore can be used for driving the core voltages of
UVLO on both supply voltages
Available in thermally-enhanced 2mm x 2mm MLF® and
Thin MLF® packages
Junction temperature range of –40C to +125C
mobile processors, post regulating
converter in any processor.
a
core DC/DC
Applications
The MIC47050 is available in fixed and adjustable output
voltages in the tiny 2mm x 2mm MLF® and Thin MLF®
packages with an operating junction temperature range of
40C to 125C.
Data sheets and support documentation can be found on
Micrel’s web site at: www.micrel.com.
Point-of-load applications
PDAs, notebooks, and desktops
Datacom and telecom systems
DSP, PLD and FPGA power supply
Low-voltage post regulation
_________________________________________________________________________________________________________________________
Typical Application
ULDO is a trademark of Micrel Inc.
MLF and MicroLeadFrame are registered trademarks of Amkor Technology, Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
M9999-040312-B
April 2012
Micrel, Inc.
MIC47050
Ordering Information
Marking
Code(2)
Temperature
Range
Lead
Part Number
Voltage (1)
Package
Finish(3)
MIC47050-1.2YML(4)
MIC47050-1.8YML(4)
MIC47050YML(4)
1.2
1.8
6-Pin 2mm x 2mm MLF®
6-Pin 2mm x 2mm MLF®
Pb-Free
40C to 125C
40C to 125C
40C to 125C
40C to 125C
40C to 125C
ZG4
Pb-Free
Pb-Free
Pb-Free
Pb-Free
ZGG
ADJ
1.2
6-Pin 2mm x 2mm MLF®
ZGA
ZG4
MIC47050-1.2YMT(5)(6)
MIC47050-1.8YMT(5)(6)
6-Pin 2mm x 2mm Thin MLF®
6-Pin 2mm x 2mm Thin MLF®
1.8
ZGG
ZGA
MIC47050YMT(5)
ADJ
6-Pin 2mm x 2mm Thin MLF®
Pb-Free
40C to 125C
Notes:
1. Other voltage available. Contact Micrel Marketing for details.
2. Overbar ( ¯ ) may not be to scale.
3. MLF® is a GREEN RoHS compliant package. Lead finish is NiPdAu. Mold compound is Halogen Free.
4. MLF® (ML) package (Pin 1 identified = ■).
5. Thin MLF® (MT) package (Pin 1 identified = ▲).
6. Contact factory for availability.
Pin Configuration
6-pin 2mm x 2mm MLF® - Fixed (ML)
6-pin 2mm x 2mm MLF® - Adjustable (ML)
6-pin 2mm x 2mm Thin MLF® - Fixed (MT)
6-pin 2mm x 2mm Thin MLF® - Adjustable (MT)
M9999-040312-B
April 2012
2
Micrel, Inc.
MIC47050
Pin Description
Fixed
ADJ
Pin Name
BIAS
Pin Function
Bias Supply. The bias supply is the power supply for the internal circuitry of the
regulator.
1
2
1
2
GND
Ground. Ground pins and exposed pad must be connected externally.
Input Supply. Drain of NMOS pass transistor which is the power input voltage for
regulator. The NMOS pass transistor steps down this input voltage to create the
output voltage.
3
4
3
4
IN
OUT
Output. Output Voltage of Regulator.
Power Good Output. Open-drain output. Output is driven low when the output voltage
is less than the power good threshold of its programmed nominal output voltage.
When the output goes above the power good threshold, the open-drain output goes
high-impedance, allowing it to be pulled up to a fixed voltage.
5
–
PGOOD
–
6
5
6
ADJ
EN
Adjust Input. Connect external resistor divider to program the output voltage.
Enable: TTL/CMOS compatible input. Logic high = enable, logic low = shutdown. Do
not leave floating.
EP
EP
GND
Exposed thermal pad. Connect to the ground plane to maximize thermal performance.
M9999-040312-B
April 2012
3
Micrel, Inc.
MIC47050
Absolute Maximum Ratings(1)
Operating Ratings(2)
IN Supply Voltage (VIN) ................................... –0.3V to +4V
Bias Supply Voltage (VBIAS)............................. –0.3V to +6V
Enable Voltage (VEN)....................................... –0.3V to +6V
Power Good Voltage (VPGOOD) ....................... .–0.3V to +6V
ADJ Pin Voltage (VADJ)................................... .–0.3V to +6V
OUT Pin Voltage (VOUT) ....................................–0.3V to VIN
Lead Temperature (soldering,10 sec.)....................... 260C
Storage Temperature (TS).........................–65C to +150C
ESD Rating(3).........................................................2kV HBM
IN Supply Voltage (VIN) ............+1.0V to +3.6V (VIN < VBIAS)
Bias Voltage (VBIAS)...................................... +2.3V to +5.5V
Enable Voltage (VEN)........................................... 0V to VBIAS
Power Good Voltage (VPGOOD) ............................0V to VBIAS
Output Voltage Range …………….. ................ 0.4V to 2.0V
Junction Temperature (TJ) ........................–40°C to +125°C
Ambient Temperature (TA) ..........................–40°C to +85°C
Junction Thermal Resistance
2mm x 2mm MLF®-6L (JA)................................90°C/W
2mm x 2mm MLF®-6L (JC)................................45°C/W
2mm x 2mm Thin MLF®-6L (JA)........................90°C/W
2mm x 2mm Thin MLF®-6L (JC) .......................45°C/W
Electrical Characteristics(4)
VIN = VOUT + 0.5V; VBIAS = VOUT+2.1V; COUT = 1µF; IOUT = 100µA; TJ = 25°C, bold values indicate –40°C≤ TJ ≤ +125°C, unless noted.
Parameter
Condition
Min.
Typ.
Max.
Units
Input Supply
Input Voltage Range (VIN)
VIN UVLO Threshold(5)
VIN UVLO Hysteresis
Ground Current in Shutdown (IGND
1.0
0.7
3.6
1.0
V
VIN Rising
0.85
40
V
mV
A
A
)
VEN ≤ 0.2V (Regulator Shutdown)
0.1
6
1.0
15
Ground Current (IGND
)
IOUT = 500mA; VIN = VOUT + 0.5V
Bias Supply
BIAS Input Voltage (VBIAS
VBIAS UVLO Threshold(5)
VBIAS UVLO Hysteresis
)
2.3
1.7
5.5
2.3
V
V
VBIAS Rising
2.1
75
mV
V
I
OUT = 100mA
1.15
1.25
330
0.1
Dropout voltage (VBIAS - VOUT
VBIAS Supply Current (IBIAS
)
IOUT = 500mA
2.1
500
1.0
V
)
IOUT = 1mA; VBIAS = VOUT + 2.1V
VEN ≤ 0.2V (Regulator Shutdown)
A
A
VBIAS Supply Current in Shutdown (IBIAS
Output Voltage
)
Dropout voltage
I
OUT = 100mA
9
50
mV
mV
(VIN - VOUT
)
IOUT = 500mA
44
120
I
OUT = 100A
-1.5
-2.0
-0.1
+1.5
+2.0
0.1
%
%
Output Voltage Accuracy
VBIAS Line Regulation
IOUT = 100A
VBIAS = VOUT + 2.1V to 5.5V
0.015
%/V
M9999-040312-B
April 2012
4
Micrel, Inc.
MIC47050
Electrical Characteristics(4)
VIN = VOUT + 0.5V; VBIAS = VOUT+2.1V; COUT = 1µF; IOUT = 100µA; TJ = 25°C, bold values indicate –40°C≤ TJ ≤ +125°C, unless noted.
Parameter
Condition
Min.
Typ.
0.005
0.2
Max.
0.05
0.5
Units
%/V
%
VIN Line Regulation
Load Regulation
Current Limit
VIN = VOUT + 0.5V to 3.6V
IOUT = 10mA to 500mA
-0.05
Short Circuit Current Limit
Enable Input
VIN = 2.7V; VOUT = 0V
0.6
1.6
2.5
A
EN Logic Level High
EN Logic Level Low
EN Hysteresis
1.0
0.77
0.67
100
1
V
V
0.2
mV
A
A
s
VEN ≤ 0.2V (Regulator Shutdown)
2
Enable Bias Current
VEN = 1.0V (Regulator Enabled)
6
10
15
500
Turn-on Time
COUT = 1F; 90% of typical VOUT
Thermal Protection
Over-Temperature Shutdown
Over-Temperature Shutdown Hysteresis
Power Good
TJ Rising
160
20
C
C
V
OUT Rising
91
89
95
%
%
%
V
Power Good Threshold Voltage
VOUT Falling
85
-1
Power Good Hysteresis
2
Power Good Output Low Voltage
Power Good Leakage Current
0.02
0.01
0.1
+1
I
PG = 250A
VPG = 5.0V
A
Reference Voltage (Adjustable Option Only)
IOUT = 100A
IOUT = 100A
VFB = 0.8V
0.394
0.406
V
V
Feedback Reference Voltage
0.4
20
0.392
0.408
FB Bias Current
nA
Output Voltage Noise and Ripple Rejection
Output Voltage Noise
63
f = 10Hz to 100kHz; IOUT = 100mA; COUT=1F
f = 10kHz; COUT = 1.0F, IOUT = 100mA
f = 100kHz; COUT = 1.0F, IOUT = 100mA
VRMS
dB
50
37
Ripple Rejection
dB
Notes:
1. Exceeding the absolute maximum rating may damage the device.
2. The device is not guaranteed to function outside its operating rating.
3. Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5kΩ in series with 100pF.
4. Specification for packaged product only.
5. Both VIN and VBIAS UVLO thresholds must be met for the output voltage to turn-on. If either of the two input voltages is below the UVLO thresholds,
the output is disabled.
M9999-040312-B
April 2012
5
Micrel, Inc.
MIC47050
Typical Characteristics
Output Voltage vs.
Input Dropout Voltage vs.
Output Current
Input Dropout Voltage vs.
Temperature
Input Voltage
50
45
40
35
30
25
20
15
10
5
2.0
70
60
50
40
30
20
10
0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
IOUT = 500mA
IOUT = 100mA
VBIAS = 3.6V
OUT = 1.2V
V
VBIAS = 5.0V
OUT = 1.8V
OUT = 500mA
0.4
0.2
0.0
VBIAS = 5.0V
VOUT = 1.2V
V
I
0
0
1
2
3
4
0
100
200
300
400
500
-40 -20
0
20
40
60
80 100 120
INPUT VOLTAGE (V)
OUTPUT CURRENT (mA)
TEMPERATURE (°C)
Output Voltage vs.
Bias Voltage
Bias Dropout Voltage vs.
Output Current
Bias Dropout Voltage vs.
Temperature
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
2.2
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
1.9
1.8
1.7
1.6
1.5
1.4
1.3
1.2
1.1
1.0
0.9
IOUT = 100mA
VOUT = 2.0V
VOUT = 2.0V
IOUT = 500mA
VOUT = 1.2V
VOUT = 1.2V
VIN = 2.5V
VIN = 2.5V
VIN = 2.5V
IOUT = 500mA
VOUT = 1.8V
2
3
4
5
0
100
200
300
400
500
-40 -20
0
20 40 60 80 100 120
BIAS VOLTAGE (V)
OUTPUT CURRENT (mA)
TEMPERATURE (°C)
Bias Current vs.
Bias Voltage
Bias Current vs.
Output Current
Bias Current vs.
Temperature
340
338
336
334
332
330
328
326
324
322
320
440
420
400
380
360
340
320
300
280
260
240
400
380
360
340
320
300
280
260
240
VBIAS = 3.6V
IN = 1.8V
VOUT = 1.2V
VBIAS = 3.6V
IN = 1.8V
VIN = 1.8V
V
V
IOUT = 1mA
VOUT = 1.2V
3
3.5
4
4.5
5
5.5
0
100
200
300
400
500
-40 -20
0
20 40 60 80 100 120
BIAS VOLT AGE (V)
OUTPUT CURRENT (mA)
TEMPERATURE (°C)
M9999-040312-B
April 2012
6
Micrel, Inc.
MIC47050
Typical Characteristics (Continued)
Ground Current vs.
Ground Current vs.
Temperature
Output Voltage vs.
Output Current
Input Voltage
30
1.208
1.206
1.204
1.202
1.200
1.198
1.196
1.194
1.192
1.190
7.00
VBIAS = 5.0V
6.75
VOUT = 1.2V
25
20
15
10
5
6.50
6.25
6.00
5.75
5.50
5.25
5.00
4.75
4.50
4.25
4.00
IOUT = 500mA
VBIAS = 3.6V
IN = 1.8V
OUT = 1.2V
V
VBIAS = 3.6V
IN = 1.8V
V
V
IOUT = 500mA
0
0
100
200
300
400
500
-40 -20
0
20 40 60 80 100 120
1.2
1.6
2
2.4
2.8
3.2
3.6
OUTPUT CURRENT (mA)
INPUT VOLTAGE (V)
TEMPERATURE (°C)
Current Limit vs.
Input Voltage
Current Limit vs.
Temperature
Output Voltage vs.
Temperature
1.80
1.75
1.70
1.65
1.60
1.55
1.50
1.45
1.40
1.220
1.215
1.210
1.205
1.200
1.195
1.190
1.185
1.180
1.90
1.85
1.80
1.75
1.70
1.65
1.60
1.55
1.50
1.45
1.40
1.35
1.30
VBIAS = 3.6V
IN = 1.8V
VBIAS = 3.6V
IN = 1.8V
V
VBIAS = 5.0V
VOUT = 1.2V
V
IOUT = 100µA
VOUT = 1.2V
1.5
2
2.5
3
3.5
4
-40 -20
0
20 40 60 80 100 120
-40 -20
0
20 40 60 80 100 120
INPUT VOLTAGE (V)
TEMPERATURE (°C)
TEMPERATURE (°C)
Power Supply Ripple Rejection
(Input Voltage)
Power Supply Ripple Rejection
(Bias Voltage)
Output Noise
90
90
10
1
80
70
60
50
40
30
20
10
0
80
70
60
50
40
30
20
10
0
0.1
VBIAS = 3.6V
IN = 1.8V
VBIAS = 3.6V
VBIAS = 3.6V ± 300mV
V
0.01
V
IN = 1.8V ± 300mV
VOUT = 1.2V
OUT = 500mA
V
IN = 1.8V
VOUT = 1.2V
VOUT = 1.2V
Noise (10Hz-100kHz) = 56.19µVRMS
I
IOUT = 500mA
0.001
0.01
0.1
1
10
100
1000
0.01
0.1
1
10
100
1000
0.01
0.1
1
10
100
1000
Frequency (kHz)
FREQUENCY (kHz)
Frequency (kHz)
M9999-040312-B
April 2012
7
Micrel, Inc.
MIC47050
Functional Characteristics
M9999-040312-B
April 2012
8
Micrel, Inc.
MIC47050
Functional Diagram
MIC47050 Fixed Output Block Diagram
MIC47050 Adjustable Output Block Diagram
M9999-040312-B
April 2012
9
Micrel, Inc.
MIC47050
Functional Description
The MIC47050 is a high-speed, ultra-low dropout, dual
supply NMOS ULDO™ designed to take advantage of
point-of-load applications that use multiple supply rails to
generate a low-voltage, high-current power supply. The
MIC47050 can source 0.5A of output current while only
requiring a 1µF ceramic output capacitor for stability.
The MIC47050 regulator is fully protected from damage
due to fault conditions, offering linear current limiting and
thermal shutdown.
Tantalum capacitors have a very stable dielectric (10%
over their operating temperature range) and can also be
used with this device. See the Typical Characteristic
section for examples of load transient response.
Output Capacitor
The MIC47050 requires an output capacitor of 1µF or
greater to maintain stability. The design is optimized for
use with low-ESR ceramic chip capacitors. High-ESR
capacitors may cause high-frequency oscillation. The
output capacitor can be increased, but performance has
been optimized for a 1µF ceramic output capacitor and
does not improve significantly with larger capacitance.
Bias Supply Voltage
VBIAS, requiring relatively light current, provides power to
the control portion of the MIC47050. Bypassing on the
bias pin is recommended to improve performance of the
regulator during line and load transients. Small 0.1µF
ceramic capacitors from VBIAS-to-ground help reduce
high frequency noise from being injected into the control
circuitry from the bias rail and are good design practice.
The output capacitor type and placement criteria are the
same as the input capacitor. See the “Input Capacitor”
subsection for a detailed description.
Minimum Load Current
The MIC47050, unlike most other regulators, does not
require a minimum load to maintain output voltage
regulation.
Input Supply Voltage
VIN provides the supply to power the LDO. The minimum
input voltage is 1.0V. This allows conversion from low
voltage supplies to reduce the power dissipation in the
pass element.
Adjustable Regulator Design
The MIC47050 adjustable version allows programming
the output voltage from 0.4V to 2.0V. Two external
resistors are required. The R1 resistor value between
Input Capacitor
The MIC47050 is a high-performance, high bandwidth
device. Therefore, it requires a well-bypassed input
supply for optimal performance. A 1µF capacitor is the
minimum required for stability. A 10µF ceramic capacitor
is recommended for most applications, especially if the
LDO’s headroom (VIN –VOUT) is small and/or large load
transients are present. Fast load transient and low
headroom requires a larger input filter capacitor to
ensure that the regulator does not drop out of regulation.
A 10µF will better attenuate any voltage glitches from
exceeding the maximum voltage rating of the part.
V
OUT and the ADJ pin should not exceed 10kꢀ, as larger
values can cause instability. R2 connects between the
ADJ pin and ground. The resistor values are calculated
as follows:
VOUT
R1 R2 V
1
REF
Where VOUT is the desired output voltage and VREF is the
internal reference voltage.
Additional high-frequency capacitors, such as small-
valued NPO dielectric-type capacitors, help filter out
high-frequency noise and are good practice in any RF-
based circuit.
Enable/Shutdown
The MIC47050 comes with a single active-high enable
pin that allows the regulator to be disabled. Forcing the
enable pin low disables the regulator and sends it into a
“zero” off-mode-current state. In this state, current
consumed by the regulator goes nearly to zero. Forcing
the enable pin high enables the output voltage. The
active-high enable pin uses CMOS technology and the
enable pin cannot be left floating; a floating enable pin
may cause an indeterminate state on the output.
X7R and X5R dielectric ceramic capacitors are
recommended
because
of
their
temperature
performance. X7R-type capacitors change capacitance
by 15% over their operating temperature range and are
the most stable type of ceramic capacitors. Z5U and
Y5V dielectric capacitors are not recommended since
they change value by as much as 50% and 60%
respectively over their operating temperature ranges. To
use a ceramic-chip capacitor with Y5V dielectric, the
value must be much higher than an X7R ceramic or a
tantalum capacitor to ensure the same capacitance
value over the operating temperature range.
M9999-040312-B
April 2012
10
Micrel, Inc.
MIC47050
TJ(MAX) = 125°C, the maximum junction temperature of
the die.
Power Good (PGOOD)
The Power Good (PGOOD) pin is an open drain output
that goes low when the output voltage (fixed version)
drops below the PGOOD threshold voltage.
θJA thermal resistance = 90°C/W.
Table 1 shows junction-to-ambient thermal resistance for
the MIC47050 in the MLF® or Thin MLF® package.
The pull-up resistor value should be large enough to
guarantee a proper “low” voltage when the PGOOD pin
pulls low. The PGOOD low voltage is typically 0.1V at
250µA current.
recommended when pulling up to 3.3V bias.
A
10kꢀ resistor or greater is
θJA Recommended
Min. Footprint
Package
θJC
6-pin 2mm x 2mm MLF®
90°C/W
45°C/W
45°C/W
If the PGOOD function is not required, the PGOOD pin
may be left unconnected.
6-pin 2mm x 2mm
Thin MLF®
90°C/W
Thermal Shutdown
Table 1. Thermal Resistance
The MIC47050 has an internal over-temperature
protection feature. This feature is for protection only.
The device should never be intentionally operated near
this temperature as this may reduce long term reliability.
The device will turn off when the over-temperature
threshold is exceeded. A 20°C hysteresis is built in to
allow the device to cool before turning back on.
Substituting PD for PD(max) and solving for the ambient
operating temperature will give the maximum operating
conditions for the regulator circuit. The junction-to-
ambient thermal resistance for the minimum footprint is
90°C/W. The maximum power dissipation must not be
exceeded for proper operation. For example, when
operating the MIC47050-1.2YML at an input voltage of
1.8V and a 0.5A load with a minimum footprint layout,
the maximum ambient operating temperature TA can be
determined as follows:
Thermal Considerations
The MIC47050 is designed to provide 0.5A of continuous
current in a very small package. Maximum ambient
operating temperature can be calculated based on the
output current and the voltage drop across the part.
Given that the input voltage is 1.8V, the output voltage is
1.2V and the output current is 0.5A. The actual power
dissipation of the regulator circuit can be determined
using the equation:
T
T
J(MAX)
Θ
P
JA D(MAX)
A
T
125C 90C/W 0.3W
98C
A
A
T
P
V
VOUT I
V I
OUT
IN GND
V
I
D
IN
BIAS BIAS
Therefore, a 1.2V application with 0.5A of output current
can accept an ambient operating temperature of 98°C in
a 2mm x 2mm MLF® or Thin MLF® package.
Because this device is CMOS, the ground current is
insignificant for power dissipation and can be ignored for
this calculation.
Thermal Measurements
Measuring the IC’s case temperature is recommended to
insure it is within its operating limits. Although this might
seem like a very elementary task, it is easy to get
erroneous results. The most common mistake is to use
the standard thermal couple that comes with a thermal
meter. This thermal couple wire gauge is large, typically
22 gauge, and behaves like a heatsink, resulting in a
lower case measurement.
P
1.8V 1.2V 0.5A 0.3W
D
To determine the maximum ambient operating
temperature of the package, use the junction-to-ambient
thermal resistance of the device and the following basic
equation:
Two methods of temperature measurement are using a
smaller thermal couple wire or an infrared thermometer.
If a thermal couple wire is used, it must be constructed
of 36 gauge wire or higher (smaller wire size) to
minimize the wire heat-sinking effect.
T
T
A
J(MAX)
P
D(MAX)
Θ
JA
M9999-040312-B
April 2012
11
Micrel, Inc.
MIC47050
In addition, the thermal couple tip must be covered in
either thermal grease or thermal glue to make sure that
the thermal couple junction is making good contact with
the case of the IC. Omega brand thermal couple (5SC-
TT-K-36-36) is adequate for most applications.
Wherever possible, an infrared thermometer is
recommended. The measurement spot size of most
infrared thermometers is too large for an accurate
reading on a small form factor ICs. However, a IR
thermometer from Optris has a 1mm spot size, which
makes it a good choice for the 2mm x 2mm MLF® or
Thin MLF® package. An optional stand makes it easy to
hold the beam on the IC for long periods of time.
For a full discussion of heat sinking and thermal effects
of voltage regulators, refer to the “Regulator Thermals”
section of Micrel’s Designing with Low-Dropout Voltage
Regulators handbook. This information can be found on
Micrel's website at:
http://www.micrel.com/_PDF/other/LDOBk_ds.pdf
M9999-040312-B
April 2012
12
Micrel, Inc.
MIC47050
MIC47050 Typical Application Schematic
MIC47050 Adjustable Output
MIC47050 Fixed Output
M9999-040312-B
April 2012
13
Micrel, Inc.
MIC47050
MIC47050 Bill of Materials
Item Part Number
Manufacturer
Murata(1)
Description
Qty.
GRM21BR60J106ME19
Ceramic Capacitor, 10µF, 6.3V, X5R, 0603 size
Ceramic Capacitor, 10µF, 6.3V, X5R, 0603 size
Capacitor, 1µF, 10V, X5R, 0402 size
C1
1
C1608X5R0J106MT
TDK(2)
Murata(1)
TDK(2)
GRM155R61A105KE15D
C2
1
C1005X5R0J105KT
Capacitor, 1µF, 10V, X5R, 0402 size
C3
R1
R2
R3
06035D104MAT2A
CRCW06031001FRT1
CRCW06036650FRT1
CRCW06031002FRT1
MIC47050YML
AVX(3)
Ceramic Capacitor, 0.1µF, 50V, X5R, 0603 size
Resistor, 1k (0603 size), 1%
1
1
1
1
Vishay Dale(4)
Vishay Dale(4)
Vishay Dale(4)
Resistor, 665 (0603 size), 1%
Resistor, 10k (0603 size), 1%
Low Input and Output 500mA ULDO™ - Adjustable Output
Low Input and Output 500mA ULDO™ - Adjustable Output
Low Input and Output 500mA ULDO™ - Fixed 1.2V Output
Low Input and Output 500mA ULDO™ - Fixed 1.2V Output
Low Input and Output 500mA ULDO™ - Fixed 1.8V Output
Low Input and Output 500mA ULDO™ - Fixed 1.8V Output
MIC47050YMT
MIC47050-1.2YML
MIC47050-1.2YMT
MIC47050-1.8YML
MIC47050-1.8YMT
U1
Micrel, Inc.(5)
1
Notes:
1. Murata: www.murata.com.
2. TDK: www.tdk.com.
3. AVX: www.avx.com.
4. Vishay: www.vishay.com .
5. Micrel, Inc.: www.micrel.com.
M9999-040312-B
April 2012
14
Micrel, Inc.
MIC47050
Package Information
6-Pin 2mm 2mm Thin MLF® (MT)
M9999-040312-B
April 2012
15
Micrel, Inc.
MIC47050
Package Information (Continued)
6-Pin 2mm x 2mm MLF® (ML)
MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA
TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com
Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this data sheet. This
information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right to change circuitry,
specifications and descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual
property rights is granted by this document. Except as provided in Micrel’s terms and conditions of sale for such products, Micrel assumes no liability
whatsoever, and Micrel disclaims any express or implied warranty relating to the sale and/or use of Micrel products including liability or warranties
relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right.
Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product
can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant
into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A
Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully
indemnify Micrel for any damages resulting from such use or sale.
© 2012 Micrel, Incorporated.
M9999-040312-B
April 2012
16
相关型号:
MIC47100-0.8YML
0.8 V FIXED POSITIVE LDO REGULATOR, 0.25 V DROPOUT, DSO8, 2 X 2 MM, GREEN, MLF-8
ROCHESTER
MIC47100-0.8YMMETR
0.8V FIXED POSITIVE LDO REGULATOR, 0.25V DROPOUT, PDSO8, LEAD FREE, MSOP-8
MICREL
MIC47100-08YMME
0.8 V FIXED POSITIVE LDO REGULATOR, 0.25 V DROPOUT, PDSO8, LEAD FREE, MSOP-8
ROCHESTER
©2020 ICPDF网 联系我们和版权申明