MIC47053YMT-TR [MICROCHIP]
ADJUSTABLE POSITIVE LDO REGULATOR;型号: | MIC47053YMT-TR |
厂家: | MICROCHIP |
描述: | ADJUSTABLE POSITIVE LDO REGULATOR 光电二极管 输出元件 调节器 |
文件: | 总14页 (文件大小:596K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MIC47053
500mA Micropower ULDO™
Linear Regulator
General Description
Features
The MIC47053 is a high-speed, adjustable output ultra-low
dropout, dual NMOS ULDO™ designed to power point-of-
load applications that require a low-voltage, high-current
power supply. The MIC47053 can source 500mA of output
current while only requiring a 1µF ceramic output capacitor
for stability. The MIC47053 offers 2% output voltage
accuracy over temperature, low dropout voltage (49mV @
500mA), and low ground current which makes this device
ideally suited for mobile and point-of-load applications.
Wide input voltage range
– Input voltage: 1.0V to 3.6V
– Bias voltage: 2.3V to 5.5V
Adjustable output voltage range down to 0.4V
Low dropout voltage of 49mV at 500mA
Low shutdown current: 0.1µA typical
±2% initial output voltage accuracy over temperature
High bandwidth – very fast transient response
Stable with a 1µF ceramic output capacitor
Logic level enable input
The MIC47053 has an NMOS output stage offering very
low output impedance. The NMOS output stage makes for
a unique ability to respond very quickly to sudden load
changes such as that required by a microprocessor, DSP
or FPGA. The MIC47053 consumes little quiescent current
and therefore can be used for driving the core voltages of
mobile processors and post regulating a core DC/DC
converter in any processor.
UVLO on both supply voltages
Available in thermally-enhanced 2mm x 2mm Thin DFN
package
Junction temperature range of –40C to +125C
The MIC47053 is available in the tiny 2mm x 2mm Thin
DFN packages with an operating junction temperature
range of 40C to 125C.
Data sheets and support documentation can be found on
Micrel’s web site at: www.micrel.com.
Applications
Point-of-load applications
PDAs, Notebooks, and Desktops
DSP, PLD, and FPGA power supply
Low-voltage post regulation
_________________________________________________________________________________________________________________________
Typical Application
ULDO is a trademark of Micrel Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
M9999-080712-C
August 2012
Micrel, Inc.
MIC47053
Ordering Information
Part Number
MIC47053YMT
Notes:
Marking Code(1)
Output Voltage
Package(2,3)
Lead Finish
Pb-Free
ADJ
8 pin 2mm x 2mm Thin DFN
Z53
1. Over bar symbol ( ¯ ) may not be to scale.
2. Thin DFN is a GREEN RoHS-compliant package. Lead finish is NiPdAu. Mold compound is Halogen Free.
3. Thin DFN package Pin 1 identifier = ▲.
Pin Configuration
8-Pin 2mm x 2mm Thin DFN (MT)
Top View
Pin Description
Pin Number
Pin Name Pin Function
1
2
BIAS
GND
Bias Supply. The bias supply is the power supply for the internal circuitry of the regulator.
Ground. Ground pins and exposed pad must be connected externally.
Input Supply. Drain of NMOS pass transistor which is the power input voltage for regulator. The
NMOS pass transistor steps down this input voltage to create the output voltage.
3, 4
IN
5
6
OUT
ADJ
Output. Output Voltage of Regulator.
Adjust Input. Connect external resistor divider to program the output voltage.
Power Good Output. Open-drain output. Output is driven low when the output voltage is less than the
power good threshold of its programmed nominal output voltage. When the output goes above the
power good threshold, the open-drain output goes high-impedance, allowing it to be pulled up to a
fixed voltage.
7
PGOOD
8
EN
Enable: TTL/CMOS compatible input. Logic high = enable, logic low = shutdown.
Exposed thermal pad. Connect to the ground plane to maximize thermal performance.
EP
ePad
M9999-080712-B
August 2012
2
Micrel, Inc.
MIC47053
Absolute Maximum Ratings(1)
Operating Ratings(2)
IN Supply Voltage (VIN) ............+1.0V to +3.6V (VIN < VBIAS
)
Bias Supply Voltage (VBIAS)............................. –0.3V to +6V
IN Supply Voltage (VIN) ................................... –0.3V to +4V
OUT Pin Voltage (VOUT) ....................................–0.3V to VIN
ADJ Pin Voltage (VADJ)................................... .–0.3V to +6V
Power Good (PGOOD) Voltage (VPGOOD)....... .–0.3V to +6V
Enable Voltage (VEN)....................................... –0.3V to +6V
Lead Temperature (soldering, 10s)............................ 260C
Storage Temperature (TS).........................–65C to +150C
ESD Rating(3)................................................. ESD Sensitive
Power Dissipation (4)………………………..Internally Limited
Bias Voltage (VBIAS)...................................... +2.3V to +5.5V
Enable Voltage (VEN)........................................... 0V to VBIAS
Power Good Voltage (VPGOOD) ............................0V to VBIAS
Output Voltage Range …………….. ................ 0.4V to 3.4V
Junction Temperature (TJ) ........................–40°C to +125°C
Ambient Temperature (TA) ........................–40°C to +125°C
Junction Thermal Resistance
2mm x 2mm Thin DFN-8L (JA) .........................90°C/W
Electrical Characteristics (5)
VIN = VOUT + 0.5V; VBIAS = VOUT+2.1V; COUT =1µF; IOUT = 100µA; TJ = 25°C, bold values indicate –40°C ≤ TJ ≤ +125°C, unless noted.
Parameter
Condition
Min.
Typ.
Max.
Units
Input Supply
Input Voltage Range (VIN)
VIN UVLO Threshold(6)
VIN UVLO Hysteresis
Ground Current in Shutdown (IGND
1.0
0.7
3.6
1.0
V
VIN Rising
0.81
25
V
mV
A
A
)
VEN = 0V (Regulator Shutdown)
IOUT = 500mA; VIN = VOUT + 0.5V
0.1
6
1.0
Ground Current (IGND
)
15
Bias Supply
BIAS Input Voltage (VBIAS
VBIAS UVLO Threshold(6)
VBIAS UVLO Hysteresis
)
2.3
1.7
5.5
2.3
V
V
VBIAS Rising
2.0
70
mV
IOUT = 100mA
IOUT = 500mA
1.3
1.4
Dropout Voltage (VBIAS - VOUT
VBIAS Supply Current (IBIAS
)
V
2.1
500
1.0
)
IOUT = 500mA; VBIAS = VOUT + 2.1V
VEN = 0V (Regulator Shutdown)
330
0.1
A
A
VBIAS Supply Current in Shutdown (IBIAS
)
Output Voltage
IOUT = 100mA
IOUT = 500mA
12
49
50
Dropout Voltage (VIN - VOUT
)
mV
120
Output Voltage Accuracy
VBIAS Line Regulation
IOUT = 100µA
+2.0
%
2.0
0.1
VBIAS = VOUT + 2.1V to 5.5V
0.1
%/V
M9999-080712-B
August 2012
3
Micrel, Inc.
MIC47053
Electrical Characteristics (5) (Continued)
VIN =VOUT + 0.5V; VBIAS =VOUT + 2.1V; COUT =1µF; IOUT=100µA; TJ=25°C, bold values indicate -40°C ≤ TJ ≤ 125°C, unless noted.
Parameter
Condition
Min.
0.05
0.5
Typ.
Max.
0.05
0.5
Units
%/V
%
VIN Line Regulation
Load Regulation
Current Limit
VIN = VOUT + 0.5V to 3.6V
IOUT = 10mA to 500mA
0.2
Short-Circuit Current Limit
Enable Input
VIN = 2.7V; VOUT = 0V
0.6
1.6
2.5
A
EN Logic Level High
EN Logic Level Low
1.0
V
V
0.2
VEN = 0V (Regulator Shutdown)
VEN = 1.0V (Regulator Enabled)
0
6
2
Enable Bias Current
A
s
10
25
500
Turn-On Time
COUT = 1µF; 90% of typical VOUT
Thermal Protection
Over-Temperature Shutdown
Over-Temperature Shutdown Hysteresis
Power Good (PGOOD)
TJ Rising
160
20
C
C
95
VOUT Rising
VOUT Falling
90.5
89.5
PGOOD Threshold Voltage
%
85
PGOOD Hysteresis
1
%
V
PGOOD Output Low Voltage
PGOOD Leakage Current
Reference Voltage
0.02
0.01
0.1
+1
IPG = 250A
VPG = 5.0V
1
A
Feedback Reference Voltage
FB Bias Current
0.392
0.4
20
0.408
V
IOUT = 100A
VFB = 0.8V
nA
Output Voltage Noise and Ripple Rejection
Output Voltage Noise
f = 10Hz to 100kHz; IOUT = 500mA; COUT =1µF
111
VRMS
f = 10kHz; COUT = 1µF, IOUT = 100mA
f = 100kHz; COUT = 1µF, IOUT = 100mA
47
35
Ripple Rejection
dB
Notes:
1. Exceeding the absolute maximum rating may damage the device.
2. The device is not guaranteed to function outside its operating rating.
3. Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5kΩ in series with 100pF.
4. The maximum allowable power dissipation of any TA (ambient temperature) is PD(MAX) = (TJ(MAX) TA ) / θJA.
5. Specification for packaged product only.
6. Both VIN and VBIAS UVLO thresholds must be met for the output voltage to turn-on. If either of the two input voltages is below the UVLO thresholds,
the output is disabled.
M9999-080712-B
August 2012
4
Micrel, Inc.
MIC47053
Typical Characteristics
Output Voltage vs.
Input Voltage
Input Droput Voltage
vs.Temperature
Input Dropout Voltage vs.
Output Current
1.40
1.20
1.00
0.80
0.60
70
60
50
40
30
20
10
0
70
60
50
40
30
20
10
0
IOUT = 500mA
IOUT = 100mA
VBIAS = 3.6V
VOUT = 1.2V
0.40
VBIAS = 5.0V
VOUT = 1.2V
IOUT = 500mA
0.20
VBIAS = 5.0V
VOUT = 1.8V
0.00
0
1
2
3
4
0
100
200
300
400
500
500
500
-40 -20
0
20
40
60
80
100 120
INPUT VOLTAGE (V)
OUTPUT CURRENT (mA)
TEMPERATURE (°C)
Output Voltage vs.
Bias Voltage
Bias Dropout Voltage vs.
Output Current
Bias Dropout Voltage vs.
Temperature
2.20
2.00
1.80
1.60
1.40
1.20
1.00
0.80
0.60
0.40
0.20
1.90
2.00
1.80
1.60
1.40
1.20
1.00
0.80
0.60
0.40
0.20
0.00
1.80
1.70
1.60
1.50
1.40
1.30
1.20
1.10
1.00
0.90
VOUT = 2.0V
VOUT = 2.0V
IOUT = 100mA
VOUT = 1.2V
IOUT = 500mA
VOUT = 1.2V
VIN = 2.5V
VIN = 2.5V
OUT = 500mA
VOUT = 1.2V
VIN = 2.5V
I
2
2.5
3
3.5
4
4.5
5
5.5
0
100
200
300
400
-40
-20
0
20
40
60
80
100 120
BIAS VOLTAGE (V)
OUTPUT CURRENT (mA)
TEMPERATURE (°C)
Bias Current vs.
Temperature
Bias Current vs.
Bias Voltage
Bias Current vs.
Output Current
440
420
400
380
360
340
320
300
280
260
240
350
348
346
344
342
340
338
336
334
332
330
400
380
360
340
320
300
280
260
240
VBIAS = 3.6V
IN = 1.8V
OUT = 1.2V
V
V
VBIAS = 3.6V
VIN = 1.8V
OUT = 1.2V
VIN = 1.8V
IOUT = 1mA
V
0
100
200
300
400
-40 -20
0
20
40
60
80 100 120
3.0
3.5
4.0
4.5
5.0
5.5
BIAS VOLTAGE (V)
OUTPUT CURRENT (mA)
TEMPERATURE ( °C )
M9999-080712-B
August 2012
5
Micrel, Inc.
MIC47053
Typical Characteristics (Continued)
Output Voltage vs.
Output Current
Ground Current vs.
Input Voltage
Ground Current vs.
Temperature
1.208
1.206
1.204
1.202
1.200
1.198
1.196
1.194
1.192
1.190
20
15
10
5
5.00
4.50
4.00
3.50
3.00
2.50
2.00
VBIAS = 5.0V
OUT = 1.2V
OUT = 500mA
V
I
VBIAS = 3.6V
VIN = 1.8V
OUT = 1.2V
IOUT = 500mA
VBIAS = 3.6V
V
VIN = 1.8V
0
0
100
200
300
400
500
1.2
1.6
2.0
2.4
2.8
3.2
3.6
-40
-20
0
20
40
60
80
100 120
OUTPUT CURRENT (mA)
INPUT VOLTAGE (V)
TEMPERATURE (°C)
Current Limit vs.
Input Voltage
Current Limit vs.
Temperature
Output Voltage vs.
Temperature
1.80
1.80
1.75
1.70
1.65
1.60
1.55
1.50
1.45
1.40
1.26
1.24
1.22
1.20
1.18
1.16
1.14
1.75
1.70
1.65
1.60
1.55
1.50
1.45
1.40
VBIAS = 3.6V
IN = 1.8V
IOUT = 100µA
VBIAS = 5.0V
VBIAS = 5.0V
VOUT = 1.2V
V
V
V
IN = 1.8V
OUT = 1.2V
1.5
2
2.5
3
3.5
4
-40
-20
0
20
40
60
80
100 120
-40
-20
0
20
40
60
80
100 120
INPUT VOLTAGE (V)
TEMPERATURE (°C)
TEMPERATURE (°C)
Power Supply Ripple Rejection
(Input Voltage)
Power Supply Rejection Ratio
(Bias Voltage)
Output Noise
90
80
70
60
50
40
30
20
10
0
90
80
70
60
50
40
30
20
10
0
10
1
0.1
`
`
VBIAS = 3.6V
VBIAS = 4.2V
VIN = 1.8V ±300mV
VOUT = 1.2V
VBIAS = 4.2V ±300mV
VIN = 1.8V
VIN = 2.1V
0.01
0.001
VOUT = 1.2V
VOUT = 1.2V
IOUT = 500mA
CBIAS = 0.1µF
IOUT = 500mA
OUT = 1µF
NOISE (10Hz-100Khz) = 111µVrms
IOUT = 500mA
C
COUT = 1µF
0.01
0.1
1
10
100
1000
0.01
0.1
1
10
100
1000
0.01
0.1
1
10
100
1000
FREQUENCY (kHz)
FREQUENCY(kHz)
FREQUENCY(kHz)
M9999-080712-B
August 2012
6
Micrel, Inc.
MIC47053
Functional Characteristics
M9999-080712-B
August 2012
7
Micrel, Inc.
MIC47053
Functional Diagram
MIC47053 Adjustable Output Block Diagram
M9999-080712-B
August 2012
8
Micrel, Inc.
MIC47053
Functional Description
The MIC47053 is a high-speed, ultra-low dropout,
NMOS ULDO designed to take advantage of point-of-
load applications that use supply rails to generate a low-
voltage, high-current power supply. The MIC47053 can
source 0.5A of output current while only requiring a 1µF
ceramic output capacitor for stability. The MIC47053
regulator is fully protected from damage due to fault
conditions, offering linear current limiting and thermal
shutdown.
Tantalum capacitors have a very stable dielectric (10%
over their operating temperature range) and can also be
used with this device.
Output Capacitor
The MIC47053 requires an output capacitor of 1µF or
greater to maintain stability. The design is optimized for
use with low-ESR ceramic chip capacitors. High-ESR
capacitors may cause high-frequency oscillation. The
output capacitor can be increased, but performance has
been optimized for a 1µF ceramic output capacitor and
does not improve significantly with larger capacitance.
(See the Typical Characteristic section for examples of
load transient response).
Bias Supply Voltage
VBIAS, requiring relatively light current, provides power to
the control portion of the MIC47053. Bypassing on the
bias pin is recommended to improve performance of the
regulator during line and load transients. Small 0.1µF
ceramic capacitors from VBIAS-to-ground help reduce
high frequency noise from being injected into the control
circuitry from the bias rail and are good design practice.
The output capacitor type and placement criteria are the
same as the input capacitor. See the “Input Capacitor”
subsection for a detailed description.
Minimum Load Current
Input Supply Voltage
The MIC47053, unlike most other regulators, does not
require a minimum load to maintain output voltage
regulation.
VIN provides the supply to power the LDO. The minimum
input voltage is 1.0V. This allows conversion from low
voltage supplies to reduce the power dissipation in the
pass element.
Adjustable Regulator Design
The MIC47053 allows programming of the output voltage
with external resistors. The R2 resistor connected
between the ADJ pin and ground should not exceed
10kꢀ, as larger values can cause instability. R1
connects between the ADJ pin and the OUT pin. The
resistor values are calculated as follows:
Input Capacitor
The MIC47053 is a high-performance, high bandwidth
device. Therefore, it requires a well-bypassed input
supply for optimal performance. A 1µF capacitor is the
minimum required for stability. A 10µF ceramic capacitor
is recommended for most applications, especially if the
LDO’s headroom (VIN –VOUT) is small and/or large load
transients are present. Fast load transient and low
headroom requires a larger input filter capacitor to
ensure that the regulator does not drop out of regulation.
A 10µF will better attenuate any voltage glitches from
exceeding the maximum voltage rating of the part.
V
OUT
0.4V
R1 R2
1
Where VOUT is the desired output voltage and 0.4V is the
internal reference voltage.
Additional high-frequency capacitors, such as small-
valued NPO dielectric-type capacitors, help filter out
high-frequency noise and are good practice in any RF-
based circuit.
Enable/Shutdown
The MIC47053 comes with a single active-high enable
pin that allows the regulator to be disabled. Forcing the
enable pin low disables the regulator and sends it into a
“zero” off-mode-current state. In this state, current
consumed by the regulator goes nearly to zero. Forcing
the enable pin high enables the output voltage.
X7R and X5R dielectric ceramic capacitors are
recommended
because
of
their
temperature
performance. X7R-type capacitors change capacitance
by 15% over their operating temperature range and are
the most stable type of ceramic capacitors. Z5U and
Y5V dielectric capacitors are not recommended since
they change value by as much as 50% and 60%
respectively over their operating temperature ranges. To
use a ceramic-chip capacitor with Y5V dielectric, the
value must be much higher than an X7R ceramic or a
tantalum capacitor to ensure the same capacitance
value over the operating temperature range.
M9999-080712-B
August 2012
9
Micrel, Inc.
MIC47053
To determine the maximum ambient operating
temperature of the package, use the junction-to-ambient
thermal resistance of the device and the following basic
equation:
Power Good (PGOOD)
The Power Good (PGOOD) pin is an open drain output
that goes low when the output voltage (fixed version)
drops below the PGOOD threshold voltage.
The pull-up resistor value should be large enough to
guarantee a proper “low” voltage when the PGOOD pin
pulls low. The PGOOD low voltage is typically 0.1V at
T
T
A
J(MAX)
P
D(MAX)
Θ
JA
250uA current.
A
10k resistor or greater is
recommended when pulling up to 3.3V bias.
TJ(MAX) = 125°C, the maximum junction temperature of
the die.
If the PGOOD function is not required, the PGOOD pin
may be left unconnected.
θ
JA thermal resistance = 90°C/W.
Thermal Shutdown
The MIC47053 has an internal over-temperature
protection feature. This feature is for protection only.
The device should never be intentionally operated near
this temperature as this may reduce long term reliability.
The device will turn off when the over-temperature
threshold is exceeded. A 20°C hysteresis is built in to
allow the device to cool before turning back on.
Table 1 shows junction-to-ambient and junction to case
thermal resistance for the MIC47053 in the thin DFN.
θJA
Recommended
Package
θJC
Minimum
Footprint
Thermal Considerations
8-pin 2mm x 2mm Thin DFN
90°C/W
45°C/W
The MIC47053 is designed to provide 0.5A of continuous
current in a very small package. Maximum ambient
operating temperature can be calculated based upon the
output current and the voltage drop across the part.
Given that the input voltage is 1.8V, the output voltage is
1.2V and the output current is 0.5A. The actual power
dissipation of the regulator circuit can be determined
using the equation:
Table 1. Thermal Resistance
Substituting PD for PD(max) and solving for the ambient
operating temperature will give the maximum operating
conditions for the regulator circuit. The junction-to-
ambient thermal resistance for the minimum footprint is
90°C/W. The maximum power dissipation must not be
exceeded for proper operation. For example, when
operating the MIC47053-1.2YMT at an input voltage of
1.8V and a 0.5A load with a minimum footprint layout,
the maximum ambient operating temperature TA can be
determined as follows:
P
V
VOUT I
V I
OUT
IN GND
V
I
D
IN
BIAS BIAS
Because this device is CMOS, the ground current is
insignificant for power dissipation and can be ignored for
this calculation.
T
T
J(MAX)
Θ
P
JA D(MAX)
A
P
1.8V 1.2V 0.5A 0.3W
D
T
125C 90C/W 0.3W
98C
A
A
T
Therefore, a 1.2V application with 0.5A of output current
can accept an ambient operating temperature of 98°C in
a 2mm x 2mm thin DFN.
M9999-080712-B
August 2012
10
Micrel, Inc.
MIC47053
Thermal Measurements
Measuring the IC’s case temperature is recommended to
ensure it is within its operating limits. Although this might
seem like a very elementary task, it is easy to get
erroneous results. The most common mistake is to use
the standard thermal couple that comes with a thermal
meter. This thermal couple wire gauge is large, typically
22 gauge, and behaves like a heatsink, resulting in a
lower case measurement.
Two methods of temperature measurement are using a
smaller thermal couple wire or an infrared thermometer.
If a thermal couple wire is used, it must be constructed
of 36 gauge wire or higher (smaller wire size) to
minimize the wire heat-sinking effect.
In addition, the thermal couple tip must be covered in
either thermal grease or thermal glue to make sure that
the thermal couple junction is making good contact with
the case of the IC. Omega brand thermal couple (5SC-
TT-K-36-36) is adequate for most applications.
Wherever possible, an infrared thermometer is
recommended. The measurement spot size of most
infrared thermometers is too large for an accurate
reading on a small form factor ICs. However, a IR
thermometer from Optris has a 1mm spot size, which
makes it a good choice for the 2mm x 2mm Thin DFN
package. An optional stand makes it easy to hold the
beam on the IC for long periods of time.
For a full discussion of heat sinking and thermal effects
of voltage regulators, refer to the “Regulator Thermals”
section of Micrel’s Designing with Low-Dropout Voltage
Regulators handbook. This information can be found on
Micrel's website at:
http://www.micrel.com/_PDF/other/LDOBk_ds.pdf
M9999-080712-B
August 2012
11
Micrel, Inc.
MIC47053
Typical Application Schematic
MIC47053 Adjustable Output
MIC47053 Bill of Materials
Item
Part Number
Manufacturer Description
Qty.
GRM21BR60J106ME19
C1608X5R0J106MT
06035D104MAT2A
Murata(1)
TDK(2)
AVX(3)
Murata(1)
TDK(2)
Ceramic Capacitor, 10µF, 6.3V, X5R, Size 0603
Ceramic Capacitor, 10µF, 6.3V, X5R, Size 0603
Ceramic Capacitor, 0.1µF, 50V, X5R, Size 0603
Ceramic Capacitor, 1µF, 10V, X5R, Size 0603
Ceramic Capacitor, 1µF, 10V, X5R, Size 0603
Resistor, 10kꢀ,1/16W, 1%, Size 0603
C1
1
1
1
C2
GRM155R61A105KE15D
C1005X5R0J105KT
C3
R1
CRCW060310K0FKEYE3
CRCW06034K99FKEYE3
CRCW060320K0FKEYE3
Vishay Dale(4)
Vishay Dale(4)
Vishay Dale(4)
1
1
2
R2
Resistor, 4.99kꢀ, 1/16W, 1%, Size 0603
Resistor, 20kꢀ, 1/16W, 1%, Size 0603
R3, R4
Low Input and Output 500mA ULDO™
Adjustable Output
U1
MIC47053YMT
Micrel, Inc.(5)
1
Notes:
1. Murata: www.murata.com
2. TDK: www.tdk.com
3. AVX: www.avx.com
4. Vishay: www.vishay.com
5. Micrel, Inc.: www.micrel.com
M9999-080712-B
August 2012
12
Micrel, Inc.
MIC47053
PCB Layout Recommendations
Top Layer
Bottom Layer
M9999-080712-B
August 2012
13
Micrel, Inc.
MIC47053
Package Information
8-Pin 2mm x 2mm Thin DFN (MT)
MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA
TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com
Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this data sheet. This
information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right to change circuitry,
specifications and descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual
property rights is granted by this document. Except as provided in Micrel’s terms and conditions of sale for such products, Micrel assumes no liability
whatsoever, and Micrel disclaims any express or implied warranty relating to the sale and/or use of Micrel products including liability or warranties
relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right.
Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product
can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical
implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A
Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully
indemnify Micrel for any damages resulting from such use or sale.
© 2012 Micrel, Incorporated.
M9999-080712-B
August 2012
14
相关型号:
MIC47100-0.8YML
0.8 V FIXED POSITIVE LDO REGULATOR, 0.25 V DROPOUT, DSO8, 2 X 2 MM, GREEN, MLF-8
ROCHESTER
MIC47100-0.8YMMETR
0.8V FIXED POSITIVE LDO REGULATOR, 0.25V DROPOUT, PDSO8, LEAD FREE, MSOP-8
MICREL
MIC47100-08YMME
0.8 V FIXED POSITIVE LDO REGULATOR, 0.25 V DROPOUT, PDSO8, LEAD FREE, MSOP-8
ROCHESTER
MIC47100-1.0YML
1 V FIXED POSITIVE LDO REGULATOR, 0.25 V DROPOUT, DSO8, 2 X 2 MM, GREEN, MLF-8
ROCHESTER
©2020 ICPDF网 联系我们和版权申明