LTC2358HLX-18#PBF [Linear]
暂无描述;型号: | LTC2358HLX-18#PBF |
厂家: | Linear |
描述: | 暂无描述 |
文件: | 总38页 (文件大小:2201K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LTC2358-18
Buffered Octal, 18-Bit, 200ksps/Ch Differential
10ꢀ2ꢁ4 ꢂDC ꢃith ꢄ04 Common Mode Range
P-P
FEATURES
DESCRIPTION
Simultaneous Sampling of 8 Buffered Channels
200ksps per Channel Throughput
500pA/12nA Max Input Leakage at 85°C/125°C
±±35LSB IꢀL ꢁMaximumꢂ ±1032.ꢃ Vangeꢄ
Guaranteed 18-Bitꢂ ꢀo Missing Codes
Differentialꢂ Wide Common Mode Vange Inputs
Per-Channel SoftSpan Input Vanges:
The LTC®2358-18 is an 18-bit, low noise 8-channel simul-
taneoussamplingsuccessiveapproximationregister(SAR)
ADC with buffered differential, wide common mode range
picoamp inputs. Operating from a 5V low voltage supply,
flexible high voltage supplies, and using the internal refer-
enceandbuffer,eachchannelofthisSoftSpanTM ADCcanbe
independently configured on a conversion-by-conversion
basis to accept 1ꢀ.2ꢁV, ꢀV to 1ꢀ.2ꢁV, 5.12V, or ꢀV to
5.12V signals. Individual channels may also be disabled
to increase throughput on the remaining channels.
n
n
n
n
n
n
n
n
±1032.ꢃꢂ 0ꢃ to 1032.ꢃꢂ ±5312ꢃꢂ 0ꢃ to 5312ꢃ
n
±1235ꢃꢂ 0ꢃ to 1235ꢃꢂ ±ꢅ325ꢃꢂ 0ꢃ to ꢅ325ꢃ
n
n
n
n
n
n
n
n
n
9ꢅ3.dB Single-Conversion SꢀV ꢁTypicalꢄ
−111dB THD ꢁTypicalꢄ at f = 2kHz
Iꢀ
Iꢀ
The integrated picoamp-input analog buffers, wide input
commonmoderangeand128dB CMRRoftheLTC2358-18
allow the ADC to directly digitize a variety of signals us-
ing minimal board space and power. This input signal
flexibility, combinedwith 3.5LSBINL, nomissingcodes
at 18 bits, and 96.ꢁdB SNR, makes the LTC2358-18 an
ideal choice for many high voltage applications requiring
wide dynamic range.
128dB CMVV ꢁTypicalꢄ at f = 200Hz
Vail-to-Vail Input Overdrive Tolerance
Integrated Reference and Buffer (ꢁ.ꢀ96V)
SPI CMOS (1.8V to 5V) and LVDS Serial I/O
Internal Conversion Clock, No Cycle Latency
219mW Power Dissipation (27mW/Ch Typical)
ꢁ8-Lead (7mm x 7mm) LQFP Package
TheLTC2358-18supportspin-selectableSPICMOS(1.8V
to 5V) and LVDS serial interfaces. Between one and eight
lanes of data output may be employed in CMOS mode,
allowing the user to optimize bus width and throughput.
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and
SoftSpan is a trademark of Analog Devices Inc. All other trademarks are the property of their
respective owners. Protected by U.S. Patents, including 77ꢀ5765, 7961132, 8319673, 9197235.
APPLICATIONS
n
Programmable Logic Controllers
Industrial Process Control
Power Line Monitoring
n
n
n
Test and Measurement
TYPICAL APPLICATION
15V
0.1µF
5V
0.1µF
1.8V TO 5V
0.1µF
2.2µF
V
Integral ꢀonlinearity vs
CMOS OR LVDS
I/O INTERFACE
Output Code and Channel
2.0
1.5
V
V
OV
DD
BUFFERS
FULLY
DIFFERENTIAL
+5V
LVDS/CMOS
CC
DD
DDLBYP
±±10.24V RANG
+
–
ARBITRARY
PD
–
IN0
IN0
TRUE BIPOLAR DRIVE (IN = 0V)
S/H
S/H
S/H
S/H
S/H
S/H
S/H
S/H
+10V
ALL CHANNELS
LTC2358-18
1.0
0V
0V
SDO0
–10V
–5V
0.5
18-BIT
MUX
0
SDO7
SCKO
SCKI
SDI
CS
BUSY
CNV
SAR ADC
UNIPOLAR
TRUE BIPOLAR
+10V
+10V
–0.5
–1.0
–1.5
–2.0
0V
0V
SAMPLE
CLOCK
–10V
–10V
+
–
IN7
IN7
+
–
V
REFBUF
REFIN
GND
EE
DIFFERENTIAL INPUTS IN /IN WITH
WIDE INPUT COMMON MODE RANGE
235818 TA01a
–131072 –65536
0
65536
131072
47µF
0.1µF
EIGHT BUFFERED
SIMULTANEOUS
SAMPLING CHANNELS
0.1µF
–15V
OUTPUT CODE
235818 TA01b
235818f
1
For more information www.linear.com/LTC2358-18
LTC2358-18
ABSOLUTE MAXIMUM RATINGS
PIN CONFIGURATION
ꢁꢀotes 1ꢂ 2ꢄ
TOP VIEW
Supply Voltage (V ) .....................–ꢀ.3V to (V + ꢁꢀV)
CC
EE
Supply Voltage (V )................................ –17.ꢁV to ꢀ.3V
EE
Supply Voltage Difference (V – V )......................ꢁꢀV
CC
EE
Supply Voltage (V )..................................................6V
DD
Supply Voltage (OV )................................................6V
DD
–
IN6
IN6
IN5
IN5
IN4
IN4
IN3
IN3
IN2
1
2
3
4
5
6
7
8
9
36 SDO7
Internal Regulated Supply Bypass (V
Analog Input Voltage
) ... (Note 3)
+
–
+
–
+
–
+
–
+
–
DDLBYP
35 SDO /SDO6
+
34 SDO /SDO5
–
33 SCKO /SDO4
32 SCKO /SCKO
+
–
+
–
+
INꢀ to IN7 ,
31 OV
DD
INꢀ to IN7 (Note ꢁ) .........(V – ꢀ.3V) to (V + ꢀ.3V)
EE
CC
30 GND
–
29 SCKI /SCKI
REFIN.................................................... –ꢀ.3V to 2.8V
+
28 SCKI /SDO3
–
IN2 10
27 SDI /SDO2
REFBUF, CNV (Note 5) ............. –ꢀ.3V to (V + ꢀ.3V)
DD
DD
DD
–
+
IN1 11
26 SDI /SDO1
+
Digital Input Voltage (Note 5)..... –ꢀ.3V to (OV + ꢀ.3V)
IN1 12
25 SDO0
Digital Output Voltage (Note 5).. –ꢀ.3V to (OV + ꢀ.3V)
Power Dissipation.............................................. 5ꢀꢀmW
Operating Temperature Range
LTC2358C................................................ ꢀ°C to 7ꢀ°C
LTC2358I .............................................–ꢁꢀ°C to 85°C
LTC2358H.......................................... –ꢁꢀ°C to 125°C
Storage Temperature Range .................. –65°C to 15ꢀ°C
LX PACKAGE
48-LEAD (7mm × 7mm) PLASTIC LQFP
T
JMAX
= 15ꢀ°C, θ = 53°C/W
JA
http://www3linear3com/product/LTC2±58-18#orderinfo
ORDER INFORMATION
TVAY
PAVT MAVKIꢀG*
PACKAGE DESCVIPTIOꢀ
TEMPEVATUVE VAꢀGE
LTC2358CLX-18#PBF
LTC2358ILX-18#PBF
LTC2358HLX-18#PBF
LTC2358LX-18
ꢁ8-Lead (7mm × 7mm) Plastic LQFP
ꢁ8-Lead (7mm × 7mm) Plastic LQFP
ꢁ8-Lead (7mm × 7mm) Plastic LQFP
ꢀ°C to 7ꢀ°C
LTC2358LX-18
LTC2358LX-18
–ꢁꢀ°C to 85°C
–ꢁꢀ°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
235818f
2
For more information www.linear.com/LTC2358-18
LTC2358-18
ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating
temperature rangeꢂ otherwise specifications are at TA = 25°C3 ꢁꢀote ꢅꢄ
SYMBOL
V +
PAVAMETEV
COꢀDITIOꢀS
MIꢀ
TYP
MAX
UꢀITS
l
l
Absolute Input Range
(Note 7)
V
V
+ ꢁ
V
– ꢁ
V
IN
EE
CC
+
+
(INꢀ to IN7 )
V –
IN
Absolute Input Range
(Note 7)
+ ꢁ
V
– ꢁ
V
EE
CC
–
–
(INꢀ to IN7 )
l
l
l
l
l
l
l
V + – V – Input Differential Voltage
SoftSpan 7: 2.5 • V
SoftSpan 6: 2.5 • V
Range (Note 7)
–2.5 •V
2.5 •V
REFBUF
2.5 •V
REFBUF
V
V
V
V
V
V
V
IN
IN
REFBUF
REFBUF
SoftSpan 5: ꢀV to 2.5 • V
SoftSpan ꢁ: ꢀV to 2.5 • V
REFBUF
REFBUF
Range
/1.ꢀ2ꢁ Range (Note 7)
–2.5 •V
/1.ꢀ2ꢁ
2.5 •V
/1.ꢀ2ꢁ
REFBUF
ꢀ
ꢀ
Range (Note 7)
REFBUF
REFBUF
REFBUF
REFBUF
/1.ꢀ2ꢁ Range (Note 7)
2.5 •V
/1.ꢀ2ꢁ
REFBUF
SoftSpan 3: 1.25 • V
SoftSpan 2: 1.25 • V
SoftSpan 1: ꢀV to 1.25 • V
Range (Note 7)
–1.25 •V
1.25 •V
REFBUF
REFBUF
/1.ꢀ2ꢁ
/1.ꢀ2ꢁ Range (Note 7)
–1.25 •V
1.25 •V
1.25 •V
REFBUF
/1.ꢀ2ꢁ
REFBUF
ꢀ
REFBUF
Range (Note 7)
REFBUF
l
V
CM
Input Common Mode Voltage (Note 7)
Range
V
EE
+ ꢁ
V – ꢁ
CC
V
l
V + – V – Input Differential Overdrive
(Note 8)
−(V − V
)
EE
(V − V
CC
)
V
IN
IN
CC
EE
Tolerance
l
l
I
I
Input Overdrive
V + > V , V – > V (Note 8)
1ꢀ
mA
mA
OVERDRIVE
IN
IN
CC IN
CC
Current Tolerance
V + < V , V – < V (Note 8)
ꢀ
IN
EE IN
EE
Analog Input Leakage Current
5
pA
pA
nA
l
l
C-Grade and I-Grade
H-Grade
5ꢀꢀ
12
R
Analog Input Resistance
Analog Input Capacitance
For Each Pin
>1ꢀꢀꢀ
3
GΩ
pF
IN
C
IN
l
CMRR
Input Common Mode
Rejection Ratio
V + = V − = 18V 2ꢀꢀHz Sine
1ꢀꢀ
1.3
128
dB
IN
IN
P-P
l
l
l
V
V
CNV High Level Input Voltage
CNV Low Level Input Voltage
CNV Input Current
V
V
IHCNV
ILCNV
INCNV
ꢀ.5
1ꢀ
I
V
= ꢀV to V
–1ꢀ
μA
IN
DD
CONVERTER CHARACTERISTICS The l denotes the specifications which apply over the full operating
temperature rangeꢂ otherwise specifications are at TA = 25°C3 ꢁꢀote 9ꢄ
SYMBOL PAVAMETEV
COꢀDITIOꢀS
MIꢀ
18
TYP
MAX
UꢀITS
Bits
l
l
Resolution
No Missing Codes
18
Bits
Transition Noise
SoftSpans 7 and 6: 1ꢀ.2ꢁV and 1ꢀV Ranges
SoftSpans 5 and ꢁ: ꢀV to 1ꢀ.2ꢁV and ꢀV to 1ꢀV Ranges
SoftSpans 3 and 2: 5.12V and 5V Ranges
SoftSpan 1: ꢀV to 5.12V Range
1.ꢁ
2.8
2.1
ꢁ.2
LSB
RMS
RMS
RMS
RMS
LSB
LSB
LSB
l
l
l
l
INL
Integral Linearity Error
SoftSpans 7 and 6: 1ꢀ.2ꢁV and 1ꢀV Ranges (Note 1ꢀ)
SoftSpans 5 and ꢁ: ꢀV to 1ꢀ.2ꢁV and ꢀV to 1ꢀV Ranges (Note 1ꢀ)
SoftSpans 3 and 2: 5.12V and 5V Ranges (Note 1ꢀ)
SoftSpan 1: ꢀV to 5.12V Range (Note 1ꢀ)
–3.5
–ꢁ
1
3.5
ꢁ
LSB
LSB
LSB
LSB
1.5
–ꢁ
ꢀ.75
ꢀ.75
ꢁ
–6
6
l
l
DNL
ZSE
Differential Linearity Error (Note 11)
−ꢀ.9
ꢀ.2
16ꢀ
ꢁ
ꢀ.9
LSB
μV
Zero-Scale Error
(Note 12)
−7ꢀꢀ
7ꢀꢀ
Zero-Scale Error Drift
Full-Scale Error
μV/°C
%FS
l
FSE
V
V
= ꢁ.ꢀ96V (REFBUF Overdriven) (Note 12)
= ꢁ.ꢀ96V (REFBUF Overdriven) (Note 12)
−ꢀ.1
ꢀ.ꢀ25
2.5
ꢀ.1
REFBUF
Full-Scale Error Drift
ppm/°C
235818f
REFBUF
3
For more information www.linear.com/LTC2358-18
LTC2358-18
DYNAMIC ACCURACY The l denotes the specifications which apply over the full operating temperature rangeꢂ
otherwise specifications are at TA = 25°C3 AIꢀ = –1dBFS3 ꢁꢀotes 9ꢂ 1±ꢄ
SYMBOL PAVAMETEV
COꢀDITIOꢀS
SoftSpans 7 and 6: 1ꢀ.2ꢁV and 1ꢀV Ranges, f = 2kHz
MIꢀ
TYP
MAX
UꢀITS
l
l
l
l
SINAD
SNR
Signal-to-(Noise +
92.7
87.3
89.3
83.6
96.2
9ꢀ.3
92.5
86.6
dB
dB
dB
dB
IN
Distortion) Ratio
SoftSpans 5 and ꢁ: ꢀV to 1ꢀ.2ꢁV and ꢀV to 1ꢀV Ranges, f = 2kHz
IN
SoftSpans 3 and 2: 5.12V and 5V Ranges, f = 2kHz
IN
SoftSpan 1: ꢀV to 5.12V Range, f = 2kHz
IN
l
l
l
l
Signal-to-Noise Ratio
SoftSpans 7 and 6: 1ꢀ.2ꢁV and 1ꢀV Ranges, f = 2kHz
93.ꢁ
87.ꢁ
89.5
83.7
96.ꢁ
9ꢀ.ꢁ
92.5
86.6
dB
dB
dB
dB
IN
SoftSpans 5 and ꢁ: ꢀV to 1ꢀ.2ꢁV and ꢀV to 1ꢀV Ranges, f = 2kHz
IN
SoftSpans 3 and 2: 5.12V and 5V Ranges, f = 2kHz
IN
SoftSpan 1: ꢀV to 5.12V Range, f = 2kHz
IN
l
l
l
l
THD
Total Harmonic Distortion
SoftSpans 7 and 6: 1ꢀ.2ꢁV and 1ꢀV Ranges, f = 2kHz
–111
–1ꢀ7
–113
–113
–1ꢀ1
–99
–1ꢀ2
–1ꢀꢀ
dB
dB
dB
dB
IN
SoftSpans 5 and ꢁ: ꢀV to 1ꢀ.2ꢁV and ꢀV to 1ꢀV Ranges, f = 2kHz
IN
SoftSpans 3 and 2: 5.12V and 5V Ranges, f = 2kHz
IN
SoftSpan 1: ꢀV to 5.12V Range, f = 2kHz
IN
l
l
l
l
SFDR
Spurious Free Dynamic
Range
SoftSpans 7 and 6: 1ꢀ.2ꢁV and 1ꢀV Ranges, f = 2kHz
1ꢀ1
99
1ꢀ3
1ꢀ3
113
1ꢀ7
113
113
dB
dB
dB
dB
IN
SoftSpans 5 and ꢁ: ꢀV to 1ꢀ.2ꢁV and ꢀV to 1ꢀV Ranges, f = 2kHz
IN
SoftSpans 3 and 2: 5.12V and 5V Ranges, f = 2kHz
IN
SoftSpan 1: ꢀV to 5.12V Range, f = 2kHz
IN
Channel-to-Channel
Crosstalk
One Channel Converting 18V 2ꢀꢀHz Sine in 1ꢀ.2ꢁV Range,
−1ꢀ9
dB
P-P
Crosstalk to All Other Channels
–3dB Input Bandwidth
Aperture Delay
6
1
MHz
ns
Aperture Delay Matching
Aperture Jitter
15ꢀ
3
ps
ps
RMS
Transient Response
Full-Scale Step, ꢀ.ꢀꢀ5% Settling
ꢁ2ꢀ
ns
INTERNAL REFERENCE CHARACTERISTICS The l denotes the specifications which apply over the full
operating temperature rangeꢂ otherwise specifications are at TA = 25°C3 ꢁꢀote 9ꢄ
SYMBOL
PAVAMETEV
COꢀDITIOꢀS
MIꢀ
TYP
2.ꢀꢁ8
5
MAX
2.ꢀ53
2ꢀ
UꢀITS
V
V
REFIN
Internal Reference Output Voltage
Internal Reference Temperature Coefficient
Internal Reference Line Regulation
Internal Reference Output Impedance
REFIN Voltage Range
2.ꢀꢁ3
l
(Note 1ꢁ)
ppm/°C
mV/V
kΩ
V
DD
= ꢁ.75V to 5.25V
ꢀ.1
2ꢀ
V
REFIN Overdriven (Note 7)
1.25
2.2
V
REFIN
REFERENCE BUFFER CHARACTERISTICS
The l denotes the specifications which apply over the full
operating temperature rangeꢂ otherwise specifications are at TA = 25°C3 ꢁꢀote 9ꢄ
SYMBOL
PAVAMETEV
COꢀDITIOꢀS
MIꢀ
ꢁ.ꢀ91
2.5
TYP
MAX
ꢁ.1ꢀ1
5
UꢀITS
l
l
V
Reference Buffer Output Voltage REFIN Overdriven, V
= 2.ꢀꢁ8V
REFIN
ꢁ.ꢀ96
V
V
REFBUF
REFBUF Voltage Range
REFBUF Input Impedance
REFBUF Load Current
REFBUF Overdriven (Notes 7, 15)
V
REFIN
= ꢀV, Buffer Disabled
13
kΩ
l
I
V
V
= 5V, 8 Channels Enabled (Notes 15, 16)
= 5V, Acquisition or Nap Mode (Note 15)
1.5
ꢀ.39
1.9
mA
mA
REFBUF
REFBUF
REFBUF
235818f
4
For more information www.linear.com/LTC2358-18
LTC2358-18
DIGITAL INPUTS AND DIGITAL OUTPUTS The l denotes the specifications which apply over the
full operating temperature rangeꢂ otherwise specifications are at TA = 25°C3 ꢁꢀote 9ꢄ
SYMBOL
PAVAMETEV
COꢀDITIOꢀS
CMOS Digital Inputs and Outputs
MIꢀ
ꢀ.8 • OV
–1ꢀ
TYP
MAX
UꢀITS
l
l
l
V
V
High Level Input Voltage
Low Level Input Voltage
Digital Input Current
V
V
IH
DD
ꢀ.2 • OV
1ꢀ
IL
DD
I
V
IN
= ꢀV to OV
DD
μA
pF
V
IN
C
V
V
Digital Input Capacitance
High Level Output Voltage
Low Level Output Voltage
Hi-Z Output Leakage Current
Output Source Current
Output Sink Current
5
IN
l
l
l
I
I
= –5ꢀꢀμA
= 5ꢀꢀμA
OV – ꢀ.2
DD
OH
OL
OUT
ꢀ.2
1ꢀ
V
OUT
I
I
I
V
OUT
V
OUT
V
OUT
= ꢀV to OV
= ꢀV
–1ꢀ
μA
mA
mA
OZ
DD
–5ꢀ
5ꢀ
SOURCE
SINK
= OV
DD
LꢃDS Digital Inputs and Outputs
l
l
V
Differential Input Voltage
2ꢀꢀ
9ꢀ
35ꢀ
6ꢀꢀ
125
mV
ID
R
On-Chip Input Termination
Resistance
CS = ꢀV, V
= 1.2V
1ꢀ6
1ꢀ
Ω
MΩ
ID
ICM
DD
CS = OV
l
l
l
l
l
V
Common-Mode Input Voltage
Common-Mode Input Current
Differential Output Voltage
ꢀ.3
–1ꢀ
275
1.1
1.2
2.2
1ꢀ
V
μA
mV
V
ICM
I
V + = V – = ꢀV to OV
IN IN DD
ICM
V
V
R = 1ꢀꢀΩ Differential Termination
L
35ꢀ
1.2
ꢁ25
1.3
1ꢀ
OD
Common-Mode Output Voltage
Hi-Z Output Leakage Current
R = 1ꢀꢀΩ Differential Termination
L
OCM
I
V
OUT
= ꢀV to OV
DD
–1ꢀ
μA
OZ
POWER REQUIREMENTS The l denotes the specifications which apply over the full operating temperature
rangeꢂ otherwise specifications are at TA = 25°C3 ꢁꢀote 9ꢄ
SYMBOL PAVAMETEV
COꢀDITIOꢀS
MIꢀ
7.5
TYP
MAX
38
UꢀITS
l
l
l
l
V
V
V
V
Supply Voltage
V
V
V
V
CC
EE
Supply Voltage
–16.5
1ꢀ
ꢀ
− V
Supply Voltage Difference
Supply Voltage
38
CC
EE
ꢁ.75
5.ꢀꢀ
5.25
DD
VCC
l
l
l
l
I
Supply Current
2ꢀꢀksps Sample Rate, 8 Channels Enabled (Note 17)
Acquisition Mode (Note 17)
Nap Mode
ꢁ.6
8.5
2.9
6
5.3
9.8
3.3
15
mA
mA
mA
μA
Power Down Mode
l
l
l
l
I
Supply Current
2ꢀꢀksps Sample Rate, 8 Channels Enabled (Note 17)
Acquisition Mode (Note 17)
Nap Mode
–5.5
–9.8
–3.5
–15
–ꢁ.5
–8
–2.8
–ꢁ
mA
mA
mA
μA
VEE
Power Down Mode
CMOS I/O Mode
l
OV
Supply Voltage
Supply Current
1.71
5.25
V
DD
l
l
l
l
l
l
I
2ꢀꢀksps Sample Rate, 8 Channels Enabled
15.6
13.8
2.1
18
16
2.7
2.ꢁ
275
5ꢀꢀ
mA
mA
mA
mA
μA
VDD
2ꢀꢀksps Sample Rate, 8 Channels Enabled, V
Acquisition Mode
= 5V (Notes 15)
REFBUF
Nap Mode
1.7
Power Down Mode (C-Grade and I-Grade)
Power Down Mode (H-Grade)
1ꢀ6
1ꢀ6
µA
235818f
5
For more information www.linear.com/LTC2358-18
LTC2358-18
POWER REQUIREMENTS The l denotes the specifications which apply over the full operating temperature
rangeꢂ otherwise specifications are at TA = 25°C3 ꢁꢀote 9ꢄ
SYMBOL PAVAMETEV
COꢀDITIOꢀS
MIꢀ
TYP
MAX
UꢀITS
l
l
l
I
Supply Current
2ꢀꢀksps Sample Rate, 8 Channels Enabled (C = 25pF)
1.6
1
1
2.6
2ꢀ
2ꢀ
mA
μA
μA
OVDD
L
Acquisition or Nap Mode
Power Down Mode
l
l
l
l
l
P
Power Dissipation
2ꢀꢀksps Sample Rate, 8 Channels Enabled
Acquisition Mode
219
258
9ꢁ
ꢀ.68
ꢀ.68
259
3ꢀ8
11ꢁ
1.9
3
mW
mW
mW
mW
mW
D
Nap Mode
Power Down Mode (C-Grade and I-Grade)
Power Down Mode (H-Grade)
LꢃDS I/O Mode
l
OV
Supply Voltage
Supply Current
2.375
5.25
V
DD
l
l
l
l
l
l
I
2ꢀꢀksps Sample Rate, 8 Channels Enabled
18.ꢁ
16.8
3.7
2ꢀ.7
19.2
ꢁ.5
ꢁ.1
275
5ꢀꢀ
mA
mA
mA
mA
μA
VDD
2ꢀꢀksps Sample Rate, 8 Channels Enabled, V
Acquisition Mode
= 5V (Note 15)
REFBUF
Nap Mode
3.ꢁ
Power Down Mode (C-Grade and I-Grade)
Power Down Mode (H-Grade)
1ꢀ6
1ꢀ6
µA
l
l
l
I
Supply Current
2ꢀꢀksps Sample Rate, 8 Channels Enabled (R = 1ꢀꢀΩ)
7
7
1
8.5
8.ꢀ
2ꢀ
mA
mA
μA
OVDD
L
Acquisition or Nap Mode (R = 1ꢀꢀΩ)
L
Power Down Mode
l
l
l
l
l
P
Power Dissipation
2ꢀꢀksps Sample Rate, 8 Channels Enabled
Acquisition Mode
2ꢁ5
28ꢁ
12ꢀ
ꢀ.68
ꢀ.68
287
337
1ꢁ3
1.9
3
mW
mW
mW
mW
mW
D
Nap Mode
Power Down Mode (C-Grade and I-Grade)
Power Down Mode (H-Grade)
ADC TIMING CHARACTERISTICS The l denotes the specifications which apply over the full operating
temperature rangeꢂ otherwise specifications are at TA = 25°C3 ꢁꢀote 9ꢄ
SYMBOL
PAVAMETEV
COꢀDITIOꢀS
MIꢀ
TYP
MAX
UꢀITS
l
l
l
l
l
l
l
l
f
Maximum Sampling Frequency
8 Channels Enabled
7 Channels Enabled
6 Channels Enabled
5 Channels Enabled
ꢁ Channels Enabled
3 Channels Enabled
2 Channels Enabled
1 Channel Enabled
2ꢀꢀ
225
25ꢀ
3ꢀꢀ
35ꢀ
ꢁ25
55ꢀ
8ꢀꢀ
ksps
ksps
ksps
ksps
ksps
ksps
ksps
ksps
SMPL
l
l
l
l
l
l
l
l
t
Time Between Conversions
8 Channels Enabled, f
7 Channels Enabled, f
6 Channels Enabled, f
5 Channels Enabled, f
ꢁ Channels Enabled, f
3 Channels Enabled, f
2 Channels Enabled, f
= 2ꢀꢀksps
= 225ksps
= 25ꢀksps
= 3ꢀꢀksps
= 35ꢀksps
= ꢁ25ksps
= 55ꢀksps
5ꢀꢀꢀ
ꢁꢁꢁꢁ
ꢁꢀꢀꢀ
3333
2855
235ꢀ
1815
125ꢀ
ns
ns
ns
ns
ns
ns
ns
ns
CYC
SMPL
SMPL
SMPL
SMPL
SMPL
SMPL
SMPL
1 Channel Enabled, f
= 8ꢀꢀksps
SMPL
l
t
t
Conversion Time
Acquisition Time
N Channels Enabled, 1 ≤ N ≤ 8
ꢁ5ꢀ•N
5ꢀꢀ•N
55ꢀ•N
ns
CONV
ACQ
l
l
l
l
l
l
l
l
8 Channels Enabled, f
7 Channels Enabled, f
6 Channels Enabled, f
5 Channels Enabled, f
ꢁ Channels Enabled, f
3 Channels Enabled, f
2 Channels Enabled, f
= 2ꢀꢀksps
= 225ksps
= 25ꢀksps
= 3ꢀꢀksps
= 35ꢀksps
= ꢁ25ksps
= 55ꢀksps
57ꢀ
56ꢁ
67ꢀ
553
625
67ꢀ
685
67ꢀ
98ꢀ
92ꢁ
98ꢀ
813
835
83ꢀ
795
73ꢀ
ns
ns
ns
ns
ns
ns
ns
SMPL
SMPL
SMPL
SMPL
SMPL
SMPL
SMPL
(t
= t
– t
– t
)
BUSYLH
ACQ
CYC
CONV
1 Channel Enabled, f
= 8ꢀꢀksps
ns
SMPL
235818f
6
For more information www.linear.com/LTC2358-18
LTC2358-18
ADC TIMING CHARACTERISTICS The l denotes the specifications which apply over the full operating
temperature rangeꢂ otherwise specifications are at TA = 25°C3 ꢁꢀote 9ꢄ
SYMBOL
PAVAMETEV
COꢀDITIOꢀS
MIꢀ
ꢁꢀ
TYP
MAX
UꢀITS
ns
l
l
l
l
l
l
t
t
t
t
t
t
t
CNV High Time
CNVH
CNVL
BUSYLH
QUIET
PDH
CNV Low Time
75ꢀ
ns
CNV↑ to BUSY Delay
Digital I/O Quiet Time from CNV↑
PD High Time
C = 25pF
L
3ꢀ
ns
2ꢀ
ꢁꢀ
ꢁꢀ
ns
ns
PD Low Time
ns
PDL
REFBUF Wake-Up Time
C
= ꢁ7μF, C = ꢀ.1μF
REFIN
2ꢀꢀ
ms
WAKE
REFBUF
CMOS I/O Mode
l
l
l
l
l
l
l
l
l
l
l
t
t
t
t
t
t
t
t
t
t
t
SCKI Period
(Notes 18, 19)
1ꢀ
ꢁ
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
SCKI
SCKI High Time
SCKIH
SCKI Low Time
ꢁ
SCKIL
SDI Setup Time from SCKI↑
SDI Hold Time from SCKI↑
SDO Data Valid Delay from SCKI↑
SDO Remains Valid Delay from SCKI↑
SDO to SCKO Skew
(Note 18)
(Note 18)
2
SSDISCKI
HSDISCKI
DSDOSCKI
HSDOSCKI
SKEW
1
C = 25pF (Note 18)
L
7.5
1
C = 25pF (Note 18)
L
1.5
–1
ꢀ
(Note 18)
ꢀ
SDO Data Valid Delay from BUSY↓
Bus Enable Time After CS↓
Bus Relinquish Time After CS↑
C = 25pF (Note 18)
L
DSDOBUSYL
EN
(Note 18)
(Note 18)
15
15
DIS
LꢃDS I/O Mode
l
l
l
l
l
l
l
l
l
l
l
t
t
t
t
t
t
t
t
t
t
t
SCKI Period
(Note 2ꢀ)
ꢁ
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
SCKI
SCKI High Time
(Note 2ꢀ)
1.5
1.5
1.2
–ꢀ.2
SCKIH
SCKI Low Time
(Note 2ꢀ)
SCKIL
SDI Setup Time from SCKI
SDI Hold Time from SCKI
SDO Data Valid Delay from SCKI
SDO Remains Valid Delay from SCKI
SDO to SCKO Skew
(Notes 11, 2ꢀ)
(Notes 11, 2ꢀ)
(Notes 11, 2ꢀ)
(Notes 11, 2ꢀ)
(Note 11)
SSDISCKI
HSDISCKI
DSDOSCKI
HSDOSCKI
SKEW
6
1
–ꢀ.ꢁ
ꢀ
ꢀ
ꢀ.ꢁ
SDO Data Valid Delay from BUSY↓
Bus Enable Time After CS↓
Bus Relinquish Time After CS↑
(Note 11)
DSDOBUSYL
EN
5ꢀ
15
DIS
235818f
7
For more information www.linear.com/LTC2358-18
LTC2358-18
ADC TIMING CHARACTERISTICS
ꢀote 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
ꢀote 10: Integral nonlinearity is defined as the deviation of a code from a
straight line passing through the actual endpoints of the transfer curve.
The deviation is measured from the center of the quantization band.
ꢀote 11: Guaranteed by design, not subject to test.
ꢀote 2: All voltage values are with respect to GND.
ꢀote 12: For bipolar SoftSpan ranges 7, 6, 3, and 2, zero-scale error
is the offset voltage measured from –ꢀ.5LSB when the output code
flickers between ꢀꢀ ꢀꢀꢀꢀ ꢀꢀꢀꢀ ꢀꢀꢀꢀ ꢀꢀꢀꢀ and 11 1111 1111 1111 1111.
Full-scale error for these SoftSpan ranges is the worst-case deviation of
the first and last code transitions from ideal and includes the effect of
offset error. For unipolar SoftSpan ranges 5, ꢁ, and 1, zero-scale error is
the offset voltage measured from ꢀ.5LSB when the output code flickers
between ꢀꢀ ꢀꢀꢀꢀ ꢀꢀꢀꢀ ꢀꢀꢀꢀ ꢀꢀꢀꢀ and ꢀꢀ ꢀꢀꢀꢀ ꢀꢀꢀꢀ ꢀꢀꢀꢀ ꢀꢀꢀ1. Full-
scale error for these SoftSpan ranges is the worst-case deviation of the
last code transition from ideal and includes the effect of offset error.
ꢀote 1±: All specifications in dB are referred to a full-scale input in the
relevant SoftSpan input range, except for crosstalk, which is referred to
the crosstalk injection signal amplitude.
ꢀote 1.: Temperature coefficient is calculated by dividing the maximum
change in output voltage by the specified temperature range.
ꢀote ±: V
is the output of an internal voltage regulator, and should
DDLBYP
only be connected to a 2.2μF ceramic capacitor to bypass the pin to GND,
as described in the Pin Functions section. Do not connect this pin to any
external circuitry.
ꢀote .: When these pin voltages are taken below V or above V , they
EE
CC
will be clamped by internal diodes. This product can handle input currents
of up to 1ꢀꢀmA below V or above V without latch-up.
EE
CC
ꢀote 5: When these pin voltages are taken below GND or above V or
DD
OV , they will be clamped by internal diodes. This product can handle
DD
currents of up to 1ꢀꢀmA below GND or above V or OV without latch-
DD
DD
up.
ꢀote ꢅ: –16.5V ≤ V ≤ ꢀV, 7.5V ≤ V ≤ 38V, 1ꢀV ≤ (V – V ) ≤ 38V,
EE
CC
CC
EE
V
DD
= 5V, unless otherwise specified.
ꢀote 7: Recommended operating conditions.
ꢀote 8: Exceeding these limits on any channel may corrupt conversion
results on other channels. Driving an analog input above V on any
ꢀote 15: When REFBUF is overdriven, the internal reference buffer must
be disabled by setting REFIN = ꢀV.
CC
ꢀote 1ꢅ: I
varies proportionally with sample rate and the number of
REFBUF
channel up to 1ꢀmA will not affect conversion results on other channels.
active channels.
Driving an analog input below V may corrupt conversion results on other
EE
channels. Refer to Applications Information section for further details.
Refer to Absolute Maximum Ratings section for pin voltage limits related
to device reliability.
ꢀote 17: Analog input buffer supply currents from I
reduced outside the acquisition period. Refer to nap mode in Applications
Information section.
and I are
VEE
VCC
ꢀote 9: V = 15V, V = –15V, V = 5V, OV = 2.5V, f
= 2ꢀꢀksps,
ꢀote 18: Parameter tested and guaranteed at OV = 1.71V, OV = 2.5V,
and OV = 5.25V.
DD
CC
EE
DD
DD
SMPL
DD DD
internal reference and buffer, true bipolar input signal drive in bipolar
SoftSpan ranges, unipolar signal drive in unipolar SoftSpan ranges, unless
otherwise specified.
ꢀote 19: A t
period of 1ꢀns minimum allows a shift clock frequency of
SCKI
up to 1ꢀꢀMHz for rising edge capture.
ꢀote 20: V = 1.2V, V = 35ꢀmV for LVDS differential input pairs.
ICM
ID
CMOS Timings
0.8 • OV
DD
t
t
WIDTH
0.2 • OV
DD
50%
50%
t
DELAY
DELAY
235818 F01
0.8 • OV
0.2 • OV
0.8 • OV
0.2 • OV
DD
DD
DD
DD
LꢃDS Timings ꢁDifferentialꢄ
+200mV
t
WIDTH
–200mV
0V
0V
t
t
DELAY
DELAY
235818 F01b
+200mV
–200mV
+200mV
–200mV
Figure 13 ꢃoltage Levels for Timing Specifications
235818f
8
For more information www.linear.com/LTC2358-18
LTC2358-18
TA = 25°C, VCC = +15V, VEE = –15V, VDD = 5V,
TYPICAL PERFORMANCE CHARACTERISTICS
OVDD = 2.5V, Internal Reference and Buffer (VREFBUF = 4.096V), fSMPL = 200ksps, unless otherwise noted.
Integral Nonlinearity
Integral Nonlinearity
Differential Nonlinearity
vs Output Code and Channel
vs Output Code and Channel
vs Output Code and Channel
0.5
0.4
2.0
1.5
2.0
1.5
ALL RANGES
ALL CHANNELS
±±10.24V RANG
±±10.24V RANG
–
–
+
TRUE BIPOLAR DRIVE (IN = 0V)
FULLY DIFFERENTIAL DRIVE (IN = –IN )
ALL CHANNELS
ALL CHANNELS
0.3
1.0
1.0
0.2
0.5
0.5
0.1
0.0
0
0
–0.1
–0.2
–0.3
–0.4
–0.5
–0.5
–1.0
–1.5
–2.0
–0.5
–1.0
–1.5
–2.0
0
65536
131072
196608
262144
–131072 –65536
0
65536
131072
–131072 –65536
0
65536
131072
OUTPUT CODE
OUTPUT CODE
OUTPUT CODE
235818 G03
235818 G01
235818 G02
Integral Nonlinearity
vs Output Code and Range
Integral Nonlinearity
vs Output Code and Range
Integral Nonlinearity
vs Output Code and Range
2.0
1.5
1.0
0.5
0
2.0
1.5
2.0
1.5
–
–
–
+
UNIPOLAR DRIVE (IN = 0V)
TRUE BIPOLAR DRIVE (IN = 0V)
FULLY DIFFERENTIAL DRIVE (IN = –IN )
ONE CHANNEL
ONE CHANNEL
ONE CHANNEL
1.0
1.0
±±5.12, AND ±±2
RANGES
0V TO 5.12V RANGE
0.5
0.5
0
0
–0.5
–1.0
–0.5
–1.0
–1.5
–2.0
–0.5
–1.0
–1.5
–2.0
±±10.24, ±±14
±±5.12V ANV±±2
RANGES
±±10.24V ANV±±14
RANGES
RANGES
–1.5 0V TO 10.24V AND
0V TO 10V RANGES
–2.0
0
65536
131072
196608
262144
–131072 –65536
0
65536
131072
–131072 –65536
0
65536
131072
OUTPUT CODE
OUTPUT CODE
OUTPUT CODE
235818 G06
235818 G04
235818 G05
Integral Nonlinearity
vs Output Code
DC Histogram (Zero-Scale)
DC Histogram (Near Full-Scale)
2.0
1.5
100000
90000
80000
70000
60000
50000
40000
30000
20000
10000
0
90000
80000
70000
60000
50000
40000
30000
20000
10000
0
±±10.24V RANG
±±10.24V RANG
±±10.24V RANG
σ = 1.4
σ = 1.35
–
TRUE BIPOLAR DRIVE (IN = 0V)
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
ARBITRARY DRIVE
+
–
IN /IN COMMON MODE
SWEPT –10.24V to 10.24V
–131072 –65536
0
65536
131072
–6
–4
–2
0
2
4
6
131024
131027
131030
131033
131036
OUTPUT CODE
CODE
CODE
235818 G07
235818 G08
235818 G09
235818f
9
For more information www.linear.com/LTC2358-18
LTC2358-18
TA = 25°C, VCC = +15V, VEE = –15V, VDD = 5V,
TYPICAL PERFORMANCE CHARACTERISTICS
OVDD = 2.5V, Internal Reference and Buffer (VREFBUF = 4.096V), fSMPL = 200ksps, unless otherwise noted.
3 2k Point Arbitrary Two-Tone FFT
fSMPL = 200kHz, IN+ = –7dBFS 2kHz
Sine, IN– = –7dBFS 3 .1kHz Sine
3 2k Point FFT fSMPL = 200kHz,
fIN = 2kHz
3 2k Point FFT fSMPL = 200kHz,
fIN = 2kHz
0
–20
0
–20
0
–20
±±10.24V RANG
±±10.24V RANG
±±10.24V RANG
ARBITRARY DRIVE
–
–
+
TRUE BIPOLAR DRIVE (IN = 0V)
FULLY DIFFERENTIAL DRIVE (IN = –IN )
SNR = 96.3dB
THD = –110dB
SINAD = 96.2dB
SFDR = 113dB
SNR = 96.4dB
THD = –114dB
SINAD = 96.3dB
SFDR = 118dB
SFDR = 119dB
SNR = 96.4dB
–40
–40
–40
–60
–60
–60
–80
–80
–80
–100
–120
–140
–160
–180
–100
–120
–140
–160
–180
–100
–120
–140
–160
–180
6.2kHz
0
20
40
60
80
100
0
20
40
60
80
100
0
20
40
60
80
100
FREQUENCY (kHz)
FREQUENCY (kHz)
FREQUENCY (kHz)
235818 G10
235818 G11
235818 G12
3 2k Point FFT fSMPL = 200kHz,
fIN = 2kHz
SNR, SINAD vs VREFBUF
,
THD, Harmonics vs VREFBUF
,
fIN = 2kHz
fIN = 2kHz
0
–20
100
98
96
94
92
90
–100
–105
–110
–115
–120
–125
–130
±±5.12V RANG
±2.5 • V
RANGE
REFBUF
±2.5 • V
RANGE
REFBUF
–
–
–
TRUE BIPOLAR DRIVE (IN = 0V)
TRUE BIPOLAR DRIVE (IN = 0V)
TRUE BIPOLAR DRIVE (IN = 0V)
SNR = 92.8dB
THD = –112dB
SINAD = 92.7dB
SFDR = 117dB
–40
SNR
–60
THD
2ND
3RD
SINAD
–80
–100
–120
–140
–160
–180
0
20
40
60
80
100
2.5
3
3.5
4
4.5
5
2.5
3
3.5
4
4.5
5
FREQUENCY (kHz)
REFBUF VOLTAGE (V)
REFBUF VOLTAGE (V)
235818 G13
235818 G14
235818 G15
SNR, SINAD
vs Input Frequency
THD, Harmonics vs Input
THD vs Input Frequency
Common Mode, fIN = 2kHz
100
95
90
85
80
75
70
65
60
0
–20
–60
–70
±±10.24V RANG
±±10.24V RANG
–
2V
P–P
FULLY DIFFERENTIAL DRIVE
TRUE BIPOLAR DRIVE (IN = 0V)
SNR
–40
–80
–60
SINAD
–90
–11V ≤ V ≤ 11V
1kΩ
CM
10kΩ
SOURCE
–80
SOURCE
–100
–110
–120
–130
–100
–120
–140
–160
THD
THD
50Ω SOURCE
±±10.24V RANG
–
TRUE BIPOLAR DRIVE (IN = 0V)
2ND
3RD
10
100
1k
10k
100k
–15
–10
–5
0
5
10
15
10
100
1k
FREQUENCY (Hz)
10k
100k
FREQUENCY (Hz)
INPUT COMMON MODE (V)
235818 G16
235818 G18
235818 G17
235818f
10
For more information www.linear.com/LTC2358-18
LTC2358-18
TA = 25°C, VCC = +15V, VEE = –15V, VDD = 5V,
TYPICAL PERFORMANCE CHARACTERISTICS
OVDD = 2.5V, Internal Reference and Buffer (VREFBUF = 4.096V), fSMPL = 200ksps, unless otherwise noted.
SNR, SINAD vs Input Level,
fIN = 2kHz
CMRR vs Input Frequency
and Channel
Crosstalk vs Input Frequency
and Channel
97.0
96.8
96.6
96.4
96.2
96.0
140
130
120
110
100
90
–80
–85
±±10.24V RANG
±±10.24V RANG
TRUE BIPOLAR DRIVE (IN = 0V)
+
–
–
±±10.24V RANG
IN = IN = 18V
SINE
P–P
+
CH1
IN0 = 0V
ALL CHANNELS
–
–90
IN0 = 18V
SINE
P–P
ALL CHANNELS CONVERTING
–95
–100
–105
–110
–115
–120
–125
–130
–135
SNR
CH2
SINAD
80
70
CH7
100k 1M
60
–40
–30
–20
–10
0
10
100
1k
10k
100k
1M
10
100
1k
10k
INPUT LEVEL (dBFS)
FREQUENCY (Hz)
FREQUENCY (Hz)
235818 G19
235818 G20
235818 G21
SNR, SINAD vs Temperature,
fIN = 2kHz
THD, Harmonics vs Temperature,
fIN = 2kHz
INL, DNL vs Temperature
98.0
97.5
97.0
96.5
96.0
95.5
95.0
94.5
94.0
–95
–100
–105
–110
–115
–120
–125
2.0
1.5
±±10.24V RANG
±±10.24V RANG
TRUE BIPOLAR DRIVE (IN = 0V)
±±10.24V RANG
–
–
–
TRUE BIPOLAR DRIVE (IN = 0V)
TRUE BIPOLAR DRIVE (IN = 0V)
ALL CHANNELS
MAX INL
1.0
0.5
SNR
MAX DNL
THD
0
SINAD
2ND
MIN DNL
–0.5
–1.0
–1.5
–2.0
3RD
MIN INL
–55 –35 –15
5
25 45 65 85 105 125
–55 –35 –15
5
25 45 65 85 105 125
–55 –35 –15
5
25 45 65 85 105 125
TEMPERATURE (°C)
TEMPERATURE (°C)
TEMPERATURE (°C)
235818 G22
235818 G23
235818 G24
Analog Input Leakage
Current vs Temperature
Positive Full-Scale Error vs
Temperature and Channel
Zero-Scale Error vs
Temperature and Channel
0.100
0.075
5
4
10k
1k
16 ANALOG INPUT PIN TRACES
FOR EACH INPUT VOLTAGE
±±10.24V RANG
REFBUF OVERDRIVEN
±±10.24V RANG
ALL CHANNELS
V
= 4.096V
REFBUF
ALL CHANNELS
3
0.050
2
0.025
1
100
10
0.000
0
–1
–2
–3
–4
–5
–0.025
–0.050
–0.075
–0.100
1
IN = 0V
IN = +10V
IN = –10V
0.1
–55 –35 –15
5
25 45 65 85 105 125
–55 –35 –15
5
25 45 65 85 105 125
–55 –35 –15
5
25 45 65 85 105 125
TEMPERATURE (°C)
TEMPERATURE (°C)
TEMPERATURE (°C)
235818 G26
235818 G27
235818 G25
235818f
11
For more information www.linear.com/LTC2358-18
LTC2358-18
TA = 25°C, VCC = +15V, VEE = –15V, VDD = 5V,
TYPICAL PERFORMANCE CHARACTERISTICS
OVDD = 2.5V, Internal Reference and Buffer (VREFBUF = 4.096V), fSMPL = 200ksps, unless otherwise noted.
Power-Down Current
vs Temperature
Supply Current vs Temperature
PSRR vs Frequency
18
16
14
12
10
8
1000
100
10
150
140
130
120
110
100
90
+
–
IN = IN = 0V
I
V
VDD
CC
I
VDD
OV
DD
I
VCC
V
EE
6
I
VCC
–I
VEE
4
1
I
2
OVDD
80
0
0.1
0.01
70
I
OVDD
–2
–4
–6
I
V
VEE
DD
60
50
–55 –35 –15
5
25 45 65 85 105 125
–55 –35 –15
5
25 45 65 85 105 125
10
100
1k
10k
100k
TEMPERATURE (°C)
TEMPERATURE (°C)
FREQUENCY (Hz)
235818 G28
235818 G29
235818 G30
Offset Error
vs Input Common Mode
Internal Reference Output
vs Temperature
Supply Current vs Sampling Rate
2.0
1.5
2.051
2.050
2.049
2.048
2.047
2.046
2.045
16
14
12
10
8
WITH NAP MODE
±±10.24V RANG
15 UNITS
t
= 1µs
CNVL
I
VDD
V
V
= 38V, V = 0V
= 4V to 34V
CC
CM
EE
1.0
0.5
6
I
VCC
0
4
V
V
= 21.5V, V = –16.5V
CC
CM
EE
–0.5
–1.0
–1.5
–2.0
2
= –12.5V to 17.5V
0
I
OVDD
–2
–4
–6
I
VEE
–17
0
17
34
–55 –35 –15
5
25 45 65 85 105 125
0
40
80
120
160
200
INPUT COMMON MODE (V)
TEMPERATURE (°C)
SAMPLING FREQUENCY (kHz)
235818 G31
235818 G32
235818 G33
Power Dissipation vs Sampling
Rate, N-Channels Enabled
Step Response
(Large-Signal Settling)
Step Response
(Fine Settling)
260
240
220
200
180
160
140
120
100
80
131072
98304
65536
32768
0
250
200
150
100
50
±±10.24V RANG
N = 1
+
IN = 199.99987kHz
N = 2
SQUARE WAVE
N = 4
–
IN = 0V
N = 8
±±10.24V RANG
+
0
IN = 199.99987kHz SQUARE WAVE
–
IN = 0V
–50
–100
–150
–200
–250
–32768
–65536
–98304
–131072
WITH NAP MODE
t
= 750ns
CNVL
0
100 200 300 400 500 600 700 800
–100
0
100 200 300 400 500 600 700 800 900
–100
0
100 200 300 400 500 600 700 800 900
SAMPLING FREQUENCY (kHz)
SETTLING TIME (ns)
SETTLING TIME (ns)
235818 G34
235818 G35
235818 G36
235818f
12
For more information www.linear.com/LTC2358-18
LTC2358-18
PIN FUNCTIONS
Pins that are the Same for All Digital I/O Modes
REFIN. With the buffer disabled, overdrive REFBUF with
an external reference voltage in the range of 2.5V to 5V.
When using the internal reference buffer, limit the loading
of any external circuitry connected to REFBUF to less than
200µA. Using a high input impedance amplifier to buffer
+
–
+
–
IN0 /IN0 toIN7 /IN7 (Pins14/13 ,12/11,10/9,8/7,6/5,
4/3 ,2/1,and48/47):PositiveandNegativeAnalogInputs,
Channels 0 to 7. The converter simultaneously samples
and digitizes (V + – V –) for all channels. Wide input
common mode range (V + 4V ≤ V ≤ V – 4V) and
IN
IN
EE
V
to any external circuits is recommended.
REFBUF
CM
CC
high common mode rejection allow the inputs to accept
a wide variety of signal swings. Full-scale input range is
determined by the channel’s SoftSpan configuration.
PD (Pin 22): Power Down Input. When this pin is brought
high, the LTC2358-18 is powered down and subsequent
conversion requests are ignored. If this occurs during a
conversion, the device powers down once the conversion
completes. If this pin is brought high twice without an
intervening conversion, an internal global reset is initi-
ated, equivalent to a power-on-reset event. Logic levels
GND (Pins 15, 18, 20, 3 0, 41, 44, 46): Ground. Solder
all GND pins to a solid ground plane.
V
(Pin 16): Positive High Voltage Power Supply. The
CC
range of V is 7.5V to 38V with respect to GND and 10V
are determined by OV .
CC
DD
to 38V with respect to V . Bypass V to GND close to
the pin with a 0.1μF ceramic capacitor.
EE
CC
LVDS/CMOS(Pin23 ):I/OModeSelect.TiethispintoOV
DD
to select LVDS I/O mode, or to ground to select CMOS I/O
V
(Pins 17, 45): Negative High Voltage Power Supply.
mode. Logic levels are determined by OV .
EE
DD
The range of V is 0V to –16.5V with respect to GND and
EE
CNV (Pin 24): Conversion Start Input. A rising edge on
this pin puts the internal sample-and-holds into the hold
mode and initiates a new conversion. CNV is not gated
by CS, allowing conversions to be initiated independent
of the state of the serial I/O bus.
–10V to –38V with respect to V . Connect Pins 17 and 45
CC
together and bypass the V network to GND close to Pin
EE
17 with a 0.1μF ceramic capacitor. In applications where
V
EE
is shorted to GND, this capacitor may be omitted.
REFIN(Pin19):BandgapReferenceOutput/ReferenceBuf-
ferInput.Aninternalbandgapreferencenominallyoutputs
2.048V on this pin. An internal reference buffer amplifies
BUSY (Pin 3 8): Busy Output. The BUSY signal indicates
that a conversion is in progress. This pin transitions low-
to-high at the start of each conversion and stays high until
the conversion is complete. Logic levels are determined
V
V
to create the converter master reference voltage
REFIN
= 2 • V
on the REFBUF pin. When using the
REFBUF
REFIN
by OV .
DD
internal reference, bypass REFIN to GND (Pin 20) close to
thepinwitha0.1μFceramiccapacitortofilterthebandgap
outputnoise. Ifmoreaccuracyisdesired, overdriveREFIN
with an external reference in the range of 1.25V to 2.2V.
Do not load this pin when internal reference is used.
V
(Pin40):Internal2.5VRegulatorBypassPin. The
DDLBYP
voltage on this pin is generated via an internal regulator
operating off of V . This pin must be bypassed to GND
DD
close to the pin with a 2.2μF ceramic capacitor. Do not
connect this pin to any external circuitry.
REFBUF (Pin 21): Internal Reference Buffer Output. An
internal reference buffer amplifies V
converter master reference voltage V
to create the
V
(Pins 42, 43 ): 5V Power Supply. The range of V
REFIN
DD DD
is 4.75V to 5.25V. Connect Pins 42 and 43 together and
= 2 • V
REFBUF
REFIN
on this pin, nominally 4.096V when using the internal
bandgapreference. BypassREFBUF to GND(Pin 20)close
to the pin with a 47μF ceramic capacitor. The internal ref-
erence buffer may be disabled by grounding its input at
bypass the V network to GND with a shared 0.1μF
ceramic capacitor close to the pins.
DD
235818f
13
For more information www.linear.com/LTC2358-18
LTC2358-18
PIN FUNCTIONS
CMOS I/O Mode
LVDS I/O Mode
SDO0 to SDO7 (Pins 25, 26, 27, 28, 3 3 , 3 4, 3 5, and 3 6):
CMOS Serial Data Outputs, Channels 0 to 7. The most
recent conversion result along with channel configuration
information is clocked out onto the SDO pins on each ris-
ing edge of SCKI. Output data formatting is described in
the Digital Interface section. Leave unused SDO outputs
SDO0, SDO7, SDI (Pins 25, 3 6, and 3 7): CMOS Serial
Data I/O. In LVDS I/O mode, these pins are Hi-Z.
+
–
SDI /SDI (Pins26/27):LVDSPositiveandNegativeSerial
+
–
Data Input. Differentially drive SDI /SDI with the desired
24-bitSoftSpanconfigurationword(seeTable1a),latched
+
–
on both the rising and falling edges of SCKI /SCKI . The
unconnected. Logic levels are determined by OV .
+
–
DD
SDI /SDI input pair is internally terminated with a 100Ω
SCKI (Pin 29): CMOS Serial Clock Input. Drive SCKI with
the serial I/O clock. SCKI rising edges latch serial data in
on SDI and clock serial data out on SDO0 to SDO7. For
standard SPI bus operation, capture output data at the
receiver on rising edges of SCKI. SCKI is allowed to idle
differential resistor when CS is low.
+
–
SCKI /SCKI (Pins 28/29): LVDS Positive and Negative
+
–
Serial Clock Input. Differentially drive SCKI /SCKI with
+
–
the serial I/O clock. SCKI /SCKI rising and falling edges
+
–
latch serial data in on SDI /SDI and clock serial data out
either high or low. Logic levels are determined by OV .
+
–
+
–
DD
on SDO /SDO . Idle SCKI /SCKI low, including when
+
–
OV (Pin 3 1): I/O Interface Power Supply. In CMOS I/O
transitioning CS. The SCKI /SCKI input pair is internally
terminatedwitha100ΩdifferentialresistorwhenCSislow.
DD
mode, the range of OV is 1.71V to 5.25V. Bypass OV
DD
DD
to GND (Pin 30) close to the pin with a 0.1μF ceramic
OV (Pin 3 1): I/O Interface Power Supply. In LVDS I/O
DD
capacitor.
mode, therangeofOV is2.375Vto5.25V. BypassOV
DD
DD
SCKO (Pin 3 2): CMOS Serial Clock Output. SCKI rising
edges trigger transitions on SCKO that are skew-matched
to the serial output data streams on SDO0 to SDO7. The
resulting SCKO frequency is half that of SCKI. Rising and
falling edges of SCKO may be used to capture SDO data
at the receiver (FPGA) in double data rate (DDR) fashion.
For standard SPI bus operation, SCKO is not used and
should be left unconnected. SCKO is forced low at the
to GND (Pin 30) close to the pin with a 0.1μF ceramic
capacitor.
+
–
SCKO /SCKO (Pins 3 2/3 3 ): LVDS Positive and Negative
+
–
Serial Clock Output. SCKO /SCKO outputs a copy of the
+
–
input serial I/O clock received on SCKI /SCKI , skew-
+
–
matchedwiththeserialoutputdatastreamonSDO /SDO .
+
–
Use the rising and falling edges of SCKO /SCKO to cap-
+
–
+
ture SDO /SDO data at the receiver (FPGA). The SCKO /
fallingedgeofBUSY. LogiclevelsaredeterminedbyOV .
–
DD
SCKO output pair must be differentially terminated with
SDI(Pin3 7):CMOSSerialDataInput.Drivethispinwiththe
desired24-bitSoftSpanconfigurationword(seeTable1a),
latched on the rising edges of SCKI. If all channels will be
a 100Ω resistor at the receiver (FPGA).
+
–
SDO /SDO (Pins 3 4/3 5): LVDS Positive and Negative
Serial Data Output. The most recent conversion result
along with channel configuration information is clocked
configured to operate only in SoftSpan 7, tie SDI to OV .
DD
Logic levels are determined by OV .
+
–
DD
out onto SDO /SDO on both rising and falling edges of
+
–
+
–
CS (Pin 3 9): Chip Select Input. The serial data I/O bus is
enabled when CS is low and is disabled and Hi-Z when
CS is high. CS also gates the external shift clock, SCKI.
SCKI /SCKI , beginning with channel 0. The SDO /SDO
output pair must be differentially terminated with a 100Ω
resistor at the receiver (FPGA).
Logic levels are determined by OV .
DD
CS (Pin 3 9): Chip Select Input. The serial data I/O bus is
enabled when CS is low, and is disabled and Hi-Z when
+
CS is high. CS also gates the external shift clock, SCKI /
–
SCKI .Theinternal100Ωdifferentialterminationresistors
+
–
+
–
ontheSCKI /SCKI andSDI /SDI inputpairsaredisabled
when CS is high. Logic levels are determined by OV .
DD
235818f
14
For more information www.linear.com/LTC2358-18
LTC2358-18
CONFIGURATION TABLES
Table 1a. SoftSpan Configuration Table. Use This Table with Table 1b to Choose Independent Binary SoftSpan Codes SS[2:0] for Each
Channel Based on Desired Analog Input Range. Combine SoftSpan Codes to Form 24-Bit SoftSpan Configuration Word S[23 :0]. Use
Serial Interface to Write SoftSpan Configuration Word to LTC23 58-18, as shown in Figure 18
BINARY SoftSpan CODE
SS[2:0]
BINARY FORMAT OF
CONVERSION RESULT
ANALOG INPUT RANGE
FULL SCALE RANGE
111
110
101
100
011
010
001
000
2.5 • V
5 • V
Two’s Complement
Two’s Complement
Straight Binary
Straight Binary
Two’s Complement
Two’s Complement
Straight Binary
All Zeros
REFBUF
REFBUF
2.5 • V
/1.024
5 • V
/1.024
REFBUF
REFBUF
0V to 2.5 • V
2.5 • V
REFBUF
REFBUF
0V to 2.5 • V
/1.024
2.5 • V
/1.024
REFBUF
REFBUF
1.25 • V
2.5 • V
REFBUF
REFBUF
1.25 • V
/1.024
2.5 • V
/1.024
REFBUF
REFBUF
0V to 1.25 • V
Channel Disabled
1.25 • V
REFBUF
Channel Disabled
REFBUF
Table 1b. Reference Configuration Table. The LTC23 58-18 Supports Three Reference Configurations. Analog Input Range Scales with
the Converter Master Reference Voltage, VREFBUF
BINARY SoftSpan CODE
REFERENCE CONFIGURATION
V
REFIN
V
ANALOG INPUT RANGE
REFBUF
SS[2:0]
111
110
101
100
011
010
001
111
110
101
100
011
010
001
111
110
101
100
011
010
001
10.24V
10V
0V to 10.24V
0V to 10V
5.12V
Internal Reference with
Internal Buffer
2.048V
4.096V
5V
0V to 5.12V
6.25V
6.104V
0V to 6.25V
0V to 6.104V
3.125V
1.25V
(Min Value)
2.5V
3.052V
External Reference with
Internal Buffer
0V to 3.125V
11V
(REFIN Pin Externally
Overdriven)
10.742V
0V to 11V
0V to 10.742V
5.5V
2.2V
(Max Value)
4.4V
5.371V
0V to 5.5V
235818f
15
For more information www.linear.com/LTC2358-18
LTC2358-18
CONFIGURATION TABLES
Table 1b. Reference Configuration Table (Continued). The LTC23 58-18 Supports Three Reference Configurations. Analog Input Range
Scales with the Converter Master Reference Voltage, VREFBUF
BINARY SoftSpan CODE
REFERENCE CONFIGURATION
V
REFIN
V
ANALOG INPUT RANGE
REFBUF
SS[2:0]
111
110
101
100
011
010
001
111
110
101
100
011
010
001
6.25V
6.104V
0V to 6.25V
0V to 6.104V
3.125V
2.5V
0V
(Min Value)
External Reference
Unbuffered
3.052V
0V to 3.125V
12.5V
(REFBUF Pin
Externally Overdriven,
REFIN Pin Grounded)
12.207V
0V to 12.5V
0V to 12.207V
6.25V
5V
0V
(Max Value)
6.104V
0V to 6.25V
235818f
16
For more information www.linear.com/LTC2358-18
LTC2358-18
FUNCTIONAL BLOCK DIAGRAM
CMOS I/O Mode
BUFFERS
V
CC
V
V
OV
DD
DD
DDLBYP
+
LTC2358-18
IN0
–
S/H
S/H
S/H
S/H
S/H
S/H
S/H
S/H
IN0
2.5V
REGULATOR
+
SDO0
IN1
–
IN1
+
IN2
–
SDO7
SCKO
SDI
CMOS
SERIAL
I/O
IN2
18-BIT
SAR ADC
18 BITS
+
IN3
INTERFACE
–
IN3
+
SCKI
CS
IN4
–
IN4
+
IN5
–
IN5
+
IN6
REFERENCE
BUFFER
–
IN6
20k
BUSY
CONTROL
LOGIC
2.048V
REFERENCE
+
IN7
2×
–
IN7
V
EE
GND
REFIN
REFBUF
CNV PD LVDS/CMOS
235818 BD01
LVDS I/O Mode
V
CC
V
V
OV
DD
BUFFERS
DD
DDLBYP
+
LTC2358-18
IN0
–
S/H
IN0
+
–
+
–
+
–
+
–
SDO
SDO
SCKO
SCKO
SDI
2.5V
+
REGULATOR
IN1
–
S/H
S/H
S/H
S/H
S/H
S/H
S/H
IN1
+
IN2
LVDS
SERIAL
I/O
–
IN2
18-BIT
18 BITS
+
SAR ADC
IN3
SDI
INTERFACE
–
IN3
SCKI
SCKI
+
IN4
–
IN4
CS
+
IN5
–
IN5
+
IN6
REFERENCE
BUFFER
–
IN6
20k
BUSY
CONTROL
LOGIC
2.048V
REFERENCE
+
IN7
2×
–
IN7
V
EE
GND
REFIN
REFBUF
CNV PD LVDS/CMOS
235818 BD02
235818f
17
For more information www.linear.com/LTC2358-18
LTC2358-18
TIMING DIAGRAM
CMOS I/O Mode
CS = PD = 0
SAMPLE N
CNV
SAMPLE N + 1
BUSY
SCKI
SDI
CONVERT
ACQUIRE
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
1
2
3
4
5
6
7
8
DON’T CARE
S23 S22 S21 S20 S19 S18 S17 S16 S15 S14 S13 S12 S11 S10 S9 S8 S7 S6 S5 S4 S3 S2 S1 S0
SoftSpan CONFIGURATION WORD FOR CONVERSION N + 1
SCKO
SDO0
DON’T CARE
DON’T CARE
D17 D16 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 C2 C1 C0 SS2 SS1 SS0 D17
CONVERSION RESULT
CHANNEL ID SoftSpan
CONVERSION RESULT
CHANNEL 0
CONVERSION N
CHANNEL 1
CONVERSION N
SDO7
D17 D16 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 C2 C1 C0 SS2 SS1 SS0 D17
CONVERSION RESULT
CHANNEL ID SoftSpan
CONVERSION RESULT
CHANNEL 7
CONVERSION N
CHANNEL 0
CONVERSION N
235818 TD01
LVDS I/O Mode
CS = PD = 0
SAMPLE
N + 1
SAMPLE N
CNV
(CMOS)
• • •
• • •
BUSY
ACQUIRE
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
(CMOS)
CONVERT
1
2
3
4
5
6
7
8
9
186 187 188 189 190 191 192
SCKI
(LVDS)
• • •
• • •
SDI
(LVDS)
DON’T CARE
S23 S22 S21 S20 S19 S18 S17 S16 S15 S14 S13 S12 S11 S10 S9 S8 S7 S6 S5 S4 S3 S2 S1 S0
SoftSpan CONFIGURATION WORD FOR CONVERSION N + 1
SCKO
(LVDS)
• • •
SDO
(LVDS)
DON’T CARE D17 D16 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 C2 C1 C0 SS2 SS1 SS0 D17 D16 D15 • • • D0 C2 C1 C0 SS2 SS1 SS0 D17
CONVERSION
RESULT
CONVERSION RESULT
CHANNEL ID SoftSpan
CHANNEL ID SoftSpan
CHANNEL 0
CONVERSION N
CHANNEL 1
CONVERSION N
CHANNEL 7
CONVERSION N
CHANNEL 0
CONVERSION N
235818 TD02
235818f
18
For more information www.linear.com/LTC2358-18
LTC2358-18
APPLICATIONS INFORMATION
OVERVIEW
CONVERTER OPERATION
The LTC2358-18 is an 18-bit, low noise 8-channel si-
multaneous sampling successive approximation register
(SAR) ADC with buffered differential, wide common
mode range picoamp inputs. The ADC operates from a
5V low voltage supply and flexible high voltage supplies,
nominally 15V. Using the integrated low-drift reference
The LTC2358-18 operates in two phases. During the ac-
quisitionphase, thesamplingcapacitorsineachchannel’s
sample-and-hold (S/H) circuit connect to their respective
analog input buffers, which track the differential analog
input voltage (V + – V –). A rising edge on the CNV pin
IN
IN
transitions all channels’ S/H circuits from track mode to
holdmode,simultaneouslysamplingtheinputsignalsonall
channelsandinitiatingaconversion.Duringtheconversion
phase,eachchannel’ssamplingcapacitorsareconnected,
one channel at a time, to an 18-bit charge redistribution
capacitor D/A converter (CDAC). The CDAC is sequenced
throughasuccessiveapproximationalgorithm,effectively
comparingthesampledinputvoltagewithbinary-weighted
fractions of the channel’s SoftSpan full-scale range (e.g.,
and buffer (V
= 4.096V nominal), each channel of
REFBUF
this SoftSpan ADC can be independently configured on a
conversion-by-conversion basis to accept 10.24V, 0V to
10.24V, 5.12V, or 0V to 5.12V signals. The input signal
range may be expanded up to 12.5V using an external
5V reference. Individual channels may also be disabled to
increase throughput on the remaining channels.
The integrated picoamp-input analog buffers, wide input
common mode range, and 128dB CMRR of the LTC2358-
18 allow the ADC to directly digitize a variety of signals
using minimal board space and power. This input signal
flexibility, combined with 3.5LSB INL, no missing codes
at 18 bits, and 96.4dB SNR, makes the LTC2358-18 an
ideal choice for many high voltage applications requiring
wide dynamic range.
V
/2, V /4 … V /262144) using a differential
FSR
FSR FSR
comparator. At the end of this process, the CDAC output
approximates the channel’s sampled analog input. Once
all channels have been converted in this manner, the ADC
control logic prepares the 18-bit digital output codes from
each channel for serial transfer.
TRANSFER FUNCTION
The absolute common mode input range (V + 4V to
EE
TheLTC2358-18digitizeseachchannel’sfull-scalevoltage
V
– 4V) is determined by the choice of high voltage
CC
18
range into 2 levels. In conjunction with the ADC master
supplies. These supplies may be biased asymmetrically
reference voltage, V
, a channel’s SoftSpan configu-
REFBUF
around ground and include the ability for V to be tied
EE
ration determines its input voltage range, full-scale range,
LSB size, and the binary format of its conversion result, as
shown in Tables 1a and 1b. For example, employing the
directly to ground.
TheLTC2358-18supportspin-selectableSPICMOS(1.8V
to 5V) and LVDS serial interfaces, enabling it to com-
municate equally well with legacy microcontrollers and
modern FPGAs. In CMOS mode, applications may employ
betweenoneandeightlanesofserialoutputdata, allowing
the user to optimize bus width and data throughput. The
LTC2358-18typicallydissipates219mWwhenconverting
eight channels simultaneously at 200ksps per channel.
Optional nap and power down modes may be employed to
furtherreducepowerconsumptionduringinactiveperiods.
internal reference and buffer (V
= 4.096V nominal),
REFBUF
SoftSpan 7 configures a channel to accept a 10.24V
bipolar analog input voltage range, which corresponds
to a 20.48V full-scale range with a 78.125μV LSB. Other
SoftSpan configurations and reference voltages may be
employed to convert both larger and smaller bipolar and
unipolar input ranges. Conversion results are output in
two’s complement binary format for all bipolar SoftSpan
ranges, and in straight binary format for all unipolar
235818f
19
For more information www.linear.com/LTC2358-18
LTC2358-18
APPLICATIONS INFORMATION
SoftSpan ranges. The ideal two’s complement transfer
function is shown in Figure 2, while the ideal straight
binary transfer function is shown in Figure 3.
LTC2358-18 enables it to accept a wide variety of signal
swings,includingtraditionalclassesofanaloginputsignals
such as pseudo-differential unipolar, pseudo-differential
true bipolar, and fully differential, simplifying signal chain
design. For conversion of signals extending to V , the
EE
011...111
unbuffered LTC2348-18 ADC is recommended.
BIPOLAR
ZERO
011...110
The wide operating range of the high voltage supplies
offers further input common mode flexibility. As long as
000...001
000...000
111...111
111...110
the voltage difference limits of 10V ≤ (V – V ) ≤ 38V
CC
EE
are observed, V and V may be independently biased
CC
EE
anywhere within their own individually allowed operating
ranges, including the ability for V to be tied directly to
EE
100...001
100...000
FSR = +FS – –FS
1LSB = FSR/262144
ground. This feature enables the common mode input
range of the LTC2358-18 to be tailored to specific ap-
plication requirements.
–1 0V
1
–FSR/2
FSR/2 – 1LSB
LSB
LSB
INPUT VOLTAGE (V)
235818 F02
In all SoftSpan ranges, each channel’s analog inputs can
be modeled by the equivalent circuit shown in Figure 4. At
Figure 2. LTC23 58-18 Two’s Complement Transfer Function
the start of acquisition, the sampling capacitors (C
)
SAMP
+
–
connecttotheintegratedbuffersBuffer /Buffer through
the sampling switches. The sampled voltage is reset dur-
ing the conversion process and is therefore re-acquired
for each new conversion.
111...111
111...110
100...001
100...000
The diodes between the inputs and the V and V sup-
CC
EE
UNIPOLAR
011...111
pliesprovideinputESDprotection.Whilewithinthesupply
voltages, the analog inputs of the LTC2358-18 draw only
5pA typical DC leakage current and the ESD protection
diodes don’t turn on. This offers a significant advantage
over external op amp buffers, which often have diode
protection that turns on during transients and corrupts
the voltage on any filter capacitors at their inputs.
ZERO
011...110
000...001
FSR = +FS
1LSB = FSR/262144
000...000
0V
FSR – 1LSB
INPUT VOLTAGE (V)
235818 F03
Figure 3 . LTC23 58-18 Straight Binary Transfer Function
V
CC
C
SAMP
+
BUFFER
R
SAMP
750Ω
30pF
+
BUFFERED ANALOG INPUTS
IN
Each channel of the LTC2358-18 simultaneously samples
V
EE
BIAS
the voltage difference (V + – V –) between its analog
IN
IN
VOLTAGE
V
CC
C
SAMP
30pF
input pins over a wide common mode input range while
attenuating unwanted signals common to both input pins
by the common-mode rejection ratio (CMRR) of the ADC.
WidecommonmodeinputrangecoupledwithhighCMRR
–
BUFFER
R
SAMP
750Ω
–
235818 F04
IN
V
EE
+
–
allows the IN /IN analog inputs to swing with an arbitrary
relationship to each other, provided each pin remains
Figure 4. Equivalent Circuit for Differential Analog
Inputs, Single Channel Shown
between (V + 4V) and (V – 4V). This feature of the
EE
CC
235818f
20
For more information www.linear.com/LTC2358-18
LTC2358-18
APPLICATIONS INFORMATION
Bipolar SoftSpan Input Ranges
less than 10kΩ of impedance can drive the passive 3pF
analog input capacitance directly. For higher impedances
and slow-settling circuits, add a 680pF capacitor at the
pins to maintain the full DC accuracy of the LTC2358-18.
For channels configured in SoftSpan ranges 7, 6, 3,
or 2, the LTC2358-18 digitizes the differential analog
input voltage (V + – V –) over a bipolar span of
IN
IN
REFBUF
2.5 • V
, 2.5 • V
/1.024, 1.25 • V ,
The very high input impedance of the unity gain buffers in
the LTC2358-18 greatly reduces the input drive require-
ments and makes it possible to include optional RC filters
with kΩ impedance and arbitrarily slow time constants
for anti-aliasing or other purposes. Micropower op amps
with limited drive capability are also well suited to drive
the high impedance analog inputs directly.
REFBUF
or 1.25 • V
REFBUF
/1.024, respectively, as shown in Table
REFBUF
1a. These SoftSpan ranges are useful for digitizing input
+
–
signals where IN and IN swing above and below each
other. Traditional examples include fully differential input
+
–
signals, where IN and IN are driven 180 degrees out-of-
phasewithrespecttoeachothercenteredaroundacommon
mode voltage (V + + V –)/2, and pseudo-differential
IN
IN
The LTC2358-18 features proprietary circuitry to achieve
exceptional internal crosstalk isolation between channels
(109dB typical). The PC board wiring to the analog inputs
shouldbeshortandshieldedtopreventexternalcapacitive
crosstalkbetweenchannels.Thecapacitancebetweenadja-
centpackagepinsis0.16pF.Lowsourceresistanceand/or
high source capacitance help reduce external capacitively
coupled crosstalk. Single ended input drive also enjoys
additionalexternalcrosstalkisolationbecauseeveryother
input pin is grounded, or at a low impedance DC source,
and serves as a shield between channels.
+
true bipolar input signals, where IN swings above and
–
below a ground reference level, driven on IN . Regardless
of the chosen SoftSpan range, the wide common mode
+
–
input range and high CMRR of the IN /IN analog inputs
allow them to swing with an arbitrary relationship to each
other, provided each pin remains between (V – 4V) and
CC
(V + 4V). The output data format for all bipolar SoftSpan
EE
ranges is two’s complement.
Unipolar SoftSpan Input Ranges
For channels configured in SoftSpan ranges 5, 4, or 1, the
LTC2358-18 digitizes the differential analog input voltage
INPUT OVERDRIVE TOLERANCE
(V + – V –) over a unipolar span of 0V to 2.5 • V ,
IN
IN
REFBUF
, respec-
Driving an analog input above V on any channel up to
0V to 2.5 • V
/1.024, or 0V to 1.25 • V
CC
REFBUF
REFBUF
10mAwillnotaffectconversionresultsonotherchannels.
Approximately 70% of this overdrive current will flow out
of the V pin and the remaining 30% will flow out of V .
tively, as shown in Table 1a. These SoftSpan ranges are
+
usefulfordigitizinginputsignalswhereIN remainsabove
–
IN . A traditional example includes pseudo-differential
CC
EE
+
This current flowing out of V will produce heat across
unipolar input signals, where IN swings above a ground
EE
–
the V –V voltage drop and must be taken into account
reference level, driven on IN . Regardless of the chosen
CC
EE
for the total Absolute Maximum power dissipation of
SoftSpan range, the wide common mode input range and
+
–
500mW. Driving an analog input below V may corrupt
high CMRR of the IN /IN analog inputs allow them to
swingwithanarbitraryrelationshiptoeachother,provided
each pin remains between (V – 4V) and (V + 4V).
EE
conversion results on other channels. This product can
handle input currents of up to 100mA below V or above
EE
CC
EE
V
without latch-up.
The output data format for all unipolar SoftSpan ranges
is straight binary.
CC
Keep in mind that driving the inputs above V or below
CC
V may reverse the normal current flow from the external
EE
INPUT DRIVE CIRCUITS
power supplies driving these pins.
The CMOS buffer input stage offers a very high degree of
transient isolation from the sampling process. Most sen-
sors,signalconditioningamplifiersandfilternetworkswith
235818f
21
For more information www.linear.com/LTC2358-18
LTC2358-18
APPLICATIONS INFORMATION
Input Filtering
each pin remains between (V – 4V) and (V + 4V). This
CC EE
feature of the LTC2358-18 enables it to accept a wide
variety of signal swings, simplifying signal chain design.
The true high impedance analog inputs can accommodate
a very wide range of passive or active signal conditioning
filters. The buffered ADC inputs have an analog bandwidth
of6MHz,andimposenoparticularbandwidthrequirement
onexternalfilters.Theexternalinputfilterscanthereforebe
optimized independent of the ADC to reduce signal chain
noise and interference. A common filter configuration is
thesimpleanti-aliasingandnoisereducingRCfilterwithits
pole at half the sampling frequency. For example, 100kHz
with R=2.43kΩ and C=680pF as shown in Figure 5.
The two-tone test shown in Figure 6b demonstrates the
arbitraryinputdrivecapabilityoftheLTC2358-18.Thistest
+
simultaneouslydrivesIN witha−7dBFS2kHzsingle-ended
−
sinewaveandIN witha−7dBFS3.1kHzsingle-endedsine
wave. Together, these signals sweep the analog inputs
across a wide range of common mode and differential
mode voltage combinations, similar to the more general
arbitrary input signal case. They also have a simple spec-
tral representation. An ideal differential converter with no
common-mode sensitivity will digitize this signal as two
−7dBFS spectral tones, one at each sine wave frequency.
The FFT plot in Figure 6b demonstrates the LTC2358-18
response approaches this ideal, with 119dB of SFDR
limited by the converter's second harmonic distortion
15V
OPTIONAL
TRUE BIPOLAR
+10V
LOWPASS FILTER
R = 2.43k
0.1µF
+
–
IN
0V
–10V
V
CC
+
–
IN0
IN0
680pF
UNIPOLAR
+10V
LTC2358-18
–
response to the 3.1kHz sine wave on IN .
IN
0V
V
REFBUF
47µF
REFIN
EE
–10V
The ability of the LTC2358-18 to accept arbitrary signal
swings over a wide input common mode range with high
CMRR can simplify application solutions. In practice,
many sensors produce a differential sensor voltage riding
on top of a large common mode signal. Figure 7a depicts
one way of using the LTC2358-18 to digitize signals of
this type. The amplifier stage provides a differential gain
of approximately 10V/V to the desired sensor signal while
the unwanted common mode signal is attenuated by the
ADCCMRR.Thecircuitemploysthe 5VSoftSpanrangeof
the ADC. Figure 7b shows measured CMRR performance
of this solution, which is competitive with the best com-
mercially available instrumentation amplifiers. Figure 7c
shows measured AC performance of this solution.
0.1µF
0.1µF
–15V
ONLY CHANNEL 0 SHOWN FOR CLARITY
235818 F05
Figure 5. Filtering Single-Ended Input Signals
High quality capacitors and resistors should be used in
the RC filters since these components can add distortion.
NPO/COG and silver mica type dielectric capacitors have
excellent linearity. Carbon surface mount resistors can
generate distortion from self-heating and from damage
thatmayoccurduringsoldering. Metalfilmsurfacemount
resistors are much less susceptible to both problems.
Arbitrary and Fully Differential Analog Input Signals
In Figure 8, another application circuit is shown which
uses two channels of the LTC2358-18 to simultaneously
sensethevoltageandbidirectionalcurrentthroughasense
resistor over a wide common mode range.
The wide common mode input range and high CMRR of
+
–
the LTC2358-18 allow each channel’s IN and IN pins to
swingwithanarbitraryrelationshiptoeachother,provided
235818f
22
For more information www.linear.com/LTC2358-18
LTC2358-18
APPLICATIONS INFORMATION
15V
FULLY
DIFFERENTIAL
+5V
ARBITRARY
+10V
0.1µF
+
–
0V
0V
IN
V
+
–
CC
IN0
IN0
–10V
–5V
LTC2358-18
UNIPOLAR
TRUE BIPOLAR
+10V
IN
+10V
V
REFBUF
47µF
REFIN
EE
0V
0V
0.1µF
0.1µF
–15V
–10V
–10V
ONLY CHANNEL 0 SHOWN FOR CLARITY
235818 F06a
Figure 6a. Input Arbitrary, Fully Differential, True Bipolar, and Unipolar Signals
Arbitrary Drive
Fully Differential Drive
0
–20
0
–20
±±10.24V RANG
SFDR = 119dB
SNR = 96.4dB
±±10.24V RANG
SNR = 96.4dB
THD = –114dB
SINAD = 96.3dB
SFDR = 118dB
–40
–40
–60
–60
–80
–80
–100
–120
–140
–160
–180
–100
–120
–140
–160
–180
6.2kHz
0
20
40
60
80
100
0
20
40
60
80
100
FREQUENCY (kHz)
FREQUENCY (kHz)
235818 F06b
235818 F06c
Figure 6b. Two-Tone Test. IN+ = –7dBFS 2kHz Sine,
IN– = –7dBFS 3 .1kHz Sine, 3 2k Point FFT, fSMPL = 200ksps.
Circuit Shown in Figure 6a
Figure 6c. IN+/IN– = –1dBFS 2kHz Fully Differential Sine,
VCM = 0V, 3 2k Point FFT, fSMPL = 200ksps. Circuit Shown in
Figure 6a
True Bipolar Drive
Unipolar Drive
0
0
±±10.24V RANG
0V to 10.24V RANGE
SNR = 96.3dB
THD = –110dB
SINAD = 96.2dB
SFDR = 113dB
SNR = 90.9dB
THD = –108dB
SINAD = 90.8dB
SFDR = 109dB
–20
–40
–20
–40
–60
–60
–80
–80
–100
–120
–140
–160
–180
–100
–120
–140
–160
–180
0
20
40
60
80
100
0
20
40
60
80
100
FREQUENCY (kHz)
FREQUENCY (kHz)
235818 F06d
235818 F06e
Figure 6d. IN+ = –1dBFS 2kHz True Bipolar Sine, IN– = 0V, 3 2k
Point FFT, fSMPL = 200ksps. Circuit Shown in Figure 6a
Figure 6e. IN+ = –1dBFS 2kHz Unipolar Sine, IN– = 0V,
3 2k Point FFT, fSMPL = 200ksps. Circuit Shown in Figure 6a
235818f
23
For more information www.linear.com/LTC2358-18
LTC2358-18
APPLICATIONS INFORMATION
INTERNAL HI-Z BUFFERS
ALLOW OPTIONAL
ARBITRARY
31V
+
31V
LTC2057HV kΩ PASSIVE FILTERS
+
–
IN
24V
3.65k
0.1µF
BUFFERED
ANALOG
INPUTS
2.49k
V
+
–
CC
COMMON MODE
INPUT RANGE
IN0
IN0
549Ω
2.49k
2.2nF
GAIN = 10
LTC2358-18
3.65k
DIFFERENTIAL MODE
INPUT RANGE: 500ꢀV
–
+
V
REFBUF
47µF
REFIN
EE
0V
BW = 10kHz
–
IN
LTC2057HV
0.1µF
0.1µF
–7V
–7V
ONLY CHANNEL 0 SHOWN FOR CLARITY
235818 F07a
Figure 7a. Amplify Differential Signals with Gain of 10
Over a Wide Common Mode Range with Buffered Analog Inputs
160
150
140
130
120
110
100
90
0
±±5V RANG
±±5V RANG
–
+
–20
–40
FULLY DIFFERENTIAL DRIVE (IN = –IN )
SNR = 91.4dB
THD = –108dB
SINAD = 91.3dB
SFDR = 109dB
–60
–80
–100
–120
–140
–160
–180
+
–
IN = IN = 1V
SINE
P–P
80
70
60
10
100
1k
10k
0
20
40
60
80
100
FREQUENCY (Hz)
FREQUENCY (kHz)
235818 F07b
235818 F07c
Figure 7c. IN+/IN– = 450mV 200Hz Fully
Differential Sine, 0V ≤ VCM ≤ 24V, 3 2k Point FFT,
fSMPL = 200ksps. Circuit Shown in Figure 7a
Figure 7b. CMRR vs Input Frequency.
Circuit Shown in Figure 7a
15V
0.1µF
V
CC
+
–
IN0
IN0
V
S1
LTC2358-18
+
IN1
IN1
R
SENSE
I
SENSE
–
V
REFBUF
47µF
REFIN
EE
V
S2
0.1µF
0.1µF
–15V
235818 F08
ONLY CHANNELS 0 AND 1 SHOWN FOR CLARITY
– V –10.24V ≤ V ≤ 10.24V
V
R
S1
S2
S1
I
=
SENSE
–10.24V ≤ V ≤ 10.24V
SENSE
S2
Figure 8. Simultaneously Sense Voltage (CH0) and Current (CH1) Over a Wide Common Mode Range
235818f
24
For more information www.linear.com/LTC2358-18
LTC2358-18
APPLICATIONS INFORMATION
ADC REFERENCE
LTC2358-18
REFIN
20k
BANDGAP
AsshownpreviouslyinTable1b, theLTC2358-18supports
three reference configurations. The first uses both the in-
ternalbandgapreferenceandreferencebuffer. Thesecond
externally overdrives the internal reference but retains the
internal buffer, which isolates the external reference from
ADC conversion transients. This configuration is ideal
for sharing a single precision external reference across
multiple ADCs. The third disables the internal buffer and
overdrives the REFBUF pin externally.
REFERENCE
0.1µF
REFBUF
REFERENCE
BUFFER
6.5k
47µF
6.5k
GND
235818 F09a
Figure 9a. Internal Reference with Internal
Buffer Configuration
Internal Reference with Internal Buffer
The LTC2358-18 has an on-chip, low noise, low drift
(20ppm/°C maximum), temperature compensated band-
gap reference that is factory trimmed to 2.048V. The
reference output connects through a 20kΩ resistor to
the REFIN pin, which serves as the input to the on-chip
reference buffer, as shown in Figure 9a. When employing
the internal bandgap reference, the REFIN pin should be
bypassed to GND (Pin 20) close to the pin with a 0.1μF
ceramic capacitor to filter wideband noise. The reference
LTC2358-18
REFIN
20k
BANDGAP
REFERENCE
2.7µF
REFBUF
REFERENCE
BUFFER
6.5k
47µF
LTC6655-2.048
6.5k
buffer amplifies V
to create the converter master
REFIN
reference voltage V
GND
= 2 • V
on the REFBUF pin,
REFBUF
REFIN
235818 F09b
nominally 4.096V when using the internal bandgap refer-
ence. BypassREFBUFtoGND(Pin20)closetothepinwith
at least a 47μF ceramic capacitor (X7R, 10V, 1210 size or
X5R, 10V, 0805 size) to compensate the reference buffer,
absorbtransientconversioncurrents,andminimizenoise.
Figure 9b. External Reference with Internal
Buffer Configuration
LTC2358-18
20k
External Reference with Internal Buffer
REFIN
BANDGAP
REFERENCE
If more accuracy and/or lower drift is desired, REFIN can
be easily overdriven by an external reference since 20kΩ
of resistance separates the internal bandgap reference
output from the REFIN pin, as shown in Figure 9b. The
valid range of external reference voltage overdrive on the
REFIN pin is 1.25V to 2.2V, resulting in converter mas-
REFBUF
REFERENCE
BUFFER
6.5k
47µF
LTC6655-5
6.5k
GND
ter reference voltages V
between 2.5V and 4.4V,
REFBUF
235818 F09c
respectively. Linear Technology offers a portfolio of high
performance references designed to meet the needs of
manyapplications.Withitssmallsize,lowpower,andhigh
accuracy,theLTC6655-2.048iswellsuitedforusewiththe
LTC2358-18 when overdriving the internal reference. The
Figure 9c. External Reference with Disabled
Internal Buffer Configuration
235818f
25
For more information www.linear.com/LTC2358-18
LTC2358-18
APPLICATIONS INFORMATION
LTC6655-2.048offers0.025%(maximum)initialaccuracy
and2ppm/°C(maximum)temperaturecoefficientforhigh
precision applications. The LTC6655-2.048 is fully speci-
fied over the H-grade temperature range, complementing
the extended temperature range of the LTC2358-18 up to
125°C.BypassingtheLTC6655-2.048witha2.7µFto100µF
ceramiccapacitorclosetotheREFINpinisrecommended.
current step triggers a transient response in the external
reference that must be considered, since any deviation in
REFBUF
is used to overdrive REFBUF, the fast settling LTC6655
family of references is recommended.
V
affectsconverteraccuracy.Ifanexternalreference
Internal Reference Buffer Transient Response
Foroptimumperformanceinapplicationsemployingburst
sampling, the external reference with internal reference
bufferconfigurationshouldbeused.Theinternalreference
buffer incorporates a proprietary design that minimizes
External Reference with Disabled Internal Buffer
The internal reference buffer supports V
= 4.4V
REFBUF
maximum. By grounding REFIN, the internal buffer may
be disabled allowing REFBUF to be overdriven with an
externalreferencevoltagebetween2.5Vand5V, asshown
in Figure 9c. Maximum input signal swing and SNR are
achieved by overdriving REFBUF using an external 5V
reference. The buffer feedback resistors load the REFBUF
pin with 13kΩ even when the reference buffer is disabled.
The LTC6655-5 offers the same small size, accuracy, drift,
and extended temperature range as the LTC6655-2.048,
and achieves a typical SNR of 97.9dB when paired with
the LTC2358-18. Bypass the LTC6655-5 to GND (Pin 20)
close to the REFBUF pin with at least a 47μF ceramic ca-
pacitor (X7R, 10V, 1210 size or X5R, 10V, 0805 size) to
absorb transient conversion currents and minimize noise.
movements in V
when responding to a burst of
REFBUF
conversions following an idle period. Figure 11 compares
the burst conversion response of the LTC2358-18 with an
input near full scale for two reference configurations. The
first configuration employs the internal reference buffer
with REFIN externally overdriven by an LTC6655-2.048,
while the second configuration disables the internal ref-
erence buffer and overdrives REFBUF with an external
LTC6655-4.096. In both cases REFBUF is bypassed to
GND with a 47µF ceramic capacitor.
20
±±10.24V RANG
+
IN = 10V
–
IN = 0V
15
The LTC2358-18 converter draws a charge (Q
) from
CONV
10
the REFBUF pin during each conversion cycle. On short
time scales most of this charge is supplied by the external
REFBUF bypass capacitor, but on longer time scales all of
the charge is supplied by either the reference buffer, or
when the internal reference buffer is disabled, the external
reference. This charge draw corresponds to a DC current
EXTERNAL REFERENCE ON REFBUF
5
0
INTERNAL REFERENCE BUFFER
–5
0
100
200
300
400
500
equivalentofI
=Q
•f
,whichisproportional
REFBUF
CONV SMPL
TIME (µs)
235818 F11
to sample rate. In applications where a burst of samples
is taken after idling for long periods of time, as shown in
Figure 11. Burst Conversion Response of the LTC23 58-18,
fSMPL = 200ksps
Figure 10, I
quickly transitions from approximately
REFBUF
0.4mA to 1.5mA (V
= 5V, f
= 200kHz). This
REFBUF
SMPL
CNV
235818 F10
IDLE
PERIOD
IDLE
PERIOD
Figure 10. CNV Waveform Showing Burst Sampling
235818f
26
For more information www.linear.com/LTC2358-18
LTC2358-18
APPLICATIONS INFORMATION
DYNAMIC PERFORMANCE
through Nth harmonics, respectively. Figure 12 shows
that the LTC2358-18 achieves a typical THD of –111dB
(N = 6) in the 1ꢀ.2ꢁ4 range at a 2ꢀꢀkHz sampling rate
with a true bipolar 2kHz input signal.
Fast Fourier transform (FFT) techniques are used to test
the ADC’s frequency response, distortion, and noise at the
rated throughput. By applying a low distortion sine wave
and analyzing the digital output using an FFT algorithm,
the ADC’s spectral content can be examined for frequen-
cies outside the fundamental. The LTC2358-18 provides
guaranteed tested limits for both AC distortion and noise
measurements.
0
±±10.24V RANG
–
TRUE BIPOLAR DRIVE (IN = 0V)
–20
–40
SNR = 96.4dB
THD = –111dB
SINAD = 96.2dB
SFDR = 113dB
–60
–80
–100
–120
–140
–160
–180
Signal-to-Noise and Distortion Ratio (SINAD)
The signal-to-noise and distortion ratio (SINAD) is the
ratiobetweentheRMSamplitudeofthefundamentalinput
frequency and the RMS amplitude of all other frequency
components at the A/D output. The output is band-limited
to frequencies below half the sampling frequency, exclud-
ing DC. Figure 12 shows that the LTC2358-18 achieves a
typical SINAD of 96.2dB in the 1ꢀ.2ꢁ4 range at a 2ꢀꢀkHz
sampling rate with a true bipolar 2kHz input signal.
0
20
40
60
80
100
FREQUENCY (kHz)
235818 F12
Figure 12. 3 2k Point FFT fSMPL = 200ksps, fIN = 2kHz
POWER CONSIDERATIONS
The LTC2358-18 requires four power supplies: the posi-
Signal-to-Noise Ratio (SNR)
tive and negative high voltage power supplies (4 and
CC
4 ), the 54 core power supply (4 ) and the digital input/
EE
DD
The signal-to-noise ratio (SNR) is the ratio between the
RMS amplitude of the fundamental input frequency and
the RMS amplitude of all other frequency components
except the first five harmonics and DC. Figure 12 shows
that the LTC2358-18 achieves a typical SNR of 96.ꢁdB in
the 1ꢀ.2ꢁ4 range at a 2ꢀꢀkHz sampling rate with a true
bipolar 2kHz input signal.
output (I/O) interface power supply (O4 ). As long as
DD
the voltage difference limits of 1ꢀ4 ≤ 4 – 4 ≤ 384
CC
EE
are observed, 4 and 4 may be independently biased
CC
EE
anywhere within their own individual allowed operating
ranges, including the ability for 4 to be tied directly to
EE
ground. This feature enables the common mode input
range of the LTC2358-18 to be tailored to the specific
application’s requirements. The flexible O4 supply al-
DD
Total Harmonic Distortion (THD)
lows the LTC2358-18 to communicate with CMOS logic
Totalharmonicdistortion(THD)istheratiooftheRMSsum
ofallharmonicsoftheinputsignaltothefundamentalitself.
The out-of-band harmonics alias into the frequency band
between DC and half the sampling frequency (f
THD is expressed as:
operating between 1.84 and 54, including 2.54 and 3.34
systems. When using L4DS I/O mode, the range of O4
is 2.3754 to 5.254.
DD
/2).
SMPL
Power Supply Sequencing
The LTC2358-18 does not have any specific power supply
sequencing requirements. Care should be taken to adhere
to the maximum voltage relationships described in the
Absolute Maximum Ratings section. The LTC2358-18 has
an internal power-on-reset (POR) circuit which resets the
422 + 432 + 4ꢁ2...4N2
THD = 2ꢀlog
41
where 4 is the RMS amplitude of the fundamental fre-
1
quencyand4 through4 aretheamplitudesofthesecond
2
N
235818f
27
For more information www.linear.com/LTC2358-18
LTC2358-18
APPLICATIONS INFORMATION
converter on initial power-up and whenever 4 drops
sion process. The CN4 timing required to take advantage
of the reduced power nap mode of operation is described
in the Nap Mode section.
DD
below 24. Once the supply voltage re-enters the nominal
supply voltage range, the POR reinitializes the ADC. No
conversions should be initiated until at least 1ꢀms after
a POR event to ensure the initialization period has ended.
Whenemployingtheinternalreferencebuffer,allow2ꢀꢀms
forthebuffertopowerupandrechargetheREFBUFbypass
capacitor. Any conversion initiated before these times will
produce invalid results.
Internal Conversion Clock
The LTC2358-18 has an internal clock that is trimmed to
achieve a maximum conversion time of 55ꢀ•N ns with N
channels enabled. With a minimum acquisition time of
57ꢀns when converting eight channels simultaneously,
throughputperformanceof2ꢀꢀkspsisguaranteedwithout
any external adjustments. Also note that the minimum
TIMING AND CONTROL
CNV Timing
acquisition time varies with sampling frequency (f
and the number of enabled channels.
)
SMPL
The LTC2358-18 sampling and conversion is controlled
by CN4. A rising edge on CN4 transitions all channels’ S/H
circuits from track mode to hold mode, simultaneously
sampling the input signals on all channels and initiating
a conversion. Once a conversion has been started, it
cannot be terminated early except by resetting the ADC,
as discussed in the Reset Timing section. For optimum
performance, drive CN4 with a clean, low jitter signal and
avoid transitions on data I/O lines leading up to the rising
edge of CN4. Additionally, to minimize channel-to-channel
crosstalk, avoid high slew rates on the analog inputs for
1ꢀꢀns before and after the rising edge of CN4. Converter
status is indicated by the BUSY output, which transitions
low-to-high at the start of each conversion and stays high
untiltheconversioniscomplete.OnceCN4 isbroughthigh
to begin a conversion, it should be returned low between
ꢁꢀns and 6ꢀns later or after the falling edge of BUSY to
minimizeexternaldisturbancesduringtheinternalconver-
Nap Mode
The LTC2358-18 can be placed into nap mode after a con-
versionhasbeencompletedtoreducepowerconsumption
between conversions. In this mode a portion of the device
circuitry is turned off, including circuits associated with
sampling the analog input signals. Nap mode is enabled
by keeping CN4 high between conversions, as shown in
Figure 13. To initiate a new conversion after entering nap
mode, bring CN4 low and hold for at least 75ꢀns before
bringingithighagain.Theconverteracquisitiontime(t
is set by the CN4 low time (t
)
ACQ
) when using nap mode.
CN4L
Power Down Mode
When PD is brought high, the LTC2358-18 is powered
down and subsequent conversion requests are ignored. If
this occurs during a conversion, the device powers down
once the conversion completes. In this mode, the device
t
CNVL
CNV
t
CONV
BUSY
NAP
t
ACQ
NAP MODE
235818 F13
Figure 13 . Nap Mode Timing for the LTC23 58-18
235818f
28
For more information www.linear.com/LTC2358-18
LTC2358-18
APPLICATIONS INFORMATION
draws only a small regulator standby current resulting in a
typical power dissipation of ꢀ.68mW. To exit power down
mode, bring the PD pin low and wait at least 1ꢀms before
initiatingaconversion. When employingtheinternal refer-
ence buffer, allow 2ꢀꢀms for the buffer to power up and
recharge the REFBUF bypass capacitor. Any conversion
initiated before these times will produce invalid results.
reduced, as shown in Figure 15. This decrease in aver-
age power dissipation occurs because a portion of the
LTC2358-18 circuitry is turned off during nap mode, and
the fraction of the conversion cycle (t ) spent napping
CYC
increasesasthesamplingfrequency(f
)isdecreased.
SMPL
16
WITH NAP MODE
CNVL
14
t
= 1µs
I
VDD
12
10
8
Reset Timing
A global reset of the LTC2358-18, equivalent to a power-
on-reset event, may be executed without needing to cycle
the supplies. This feature is useful when recovering from
system-level events that require the state of the entire sys-
tem to be reset to a known synchronized value. To initiate
a global reset, bring PD high twice without an intervening
conversion, as shown in Figure 1ꢁ. The reset event is trig-
geredonthesecondrisingedgeofPD,andasynchronously
ends based on an internal timer. Reset clears all serial data
outputregistersandrestorestheinternalSoftSpanconfigu-
ration register default state of all channels in SoftSpan 7.
If reset is triggered during a conversion, the conversion
is immediately halted. The normal power down behavior
associatedwithPDgoinghighisnotaffectedbyreset.Once
PD is brought low, wait at least 1ꢀms before initiating a
conversion. When employing the internal reference buffer,
allow 2ꢀꢀms for the buffer to power up and recharge the
REFBUF bypass capacitor. Any conversion initiated before
these times will produce invalid results.
6
I
VCC
4
2
0
I
OVDD
–2
–4
–6
I
VEE
0
40
80
120
160
200
SAMPLING FREQUENCY (kHz)
235818 F15
Figure 15. Power Dissipation of the LTC23 58-18
Decreases with Decreasing Sampling Frequency
DIGITAL INTERFACE
TheLTC2358-18featuresCMOSandL4DSserialinterfaces,
selectable using the L4DS/CMOS pin. The flexible O4
DD
supply allows the LTC2358-18 to communicate with any
CMOS logic operating between 1.84 and 54, including
2.54 and 3.34 systems, while the L4DS interface supports
low noise digital designs. In CMOS mode, applications
may employ between one and eight lanes of serial data
output, allowing the user to optimize bus width and data
throughput. Together, these I/O interface options enable
the LTC2358-18 to communicate equally well with legacy
microcontrollers and modern FPGAs.
Power Dissipation vs Sampling Frequency
When nap mode is employed, the power dissipation of
the LTC2358-18 decreases as the sampling frequency is
t
PDH
t
PD
WAKE
t
t
PDL
CNVH
CNV
SECOND RISING EDGE OF
PD TRIGGERS RESET
BUSY
t
CONV
RESET TIME
SET INTERNALLY
RESET
235818 F14
Figure 14. Reset Timing for the LTC23 58-18
235818f
29
For more information www.linear.com/LTC2358-18
LTC2358-18
APPLICATIONS INFORMATION
CS = PD = 0
SAMPLE N
SAMPLE N + 1
t
CYC
t
CNVH
t
CNV
CNVL
BUSY
t
t
CONV
ACQ
t
RECOMMENDED DATA TRANSACTION WINDOW
BUSYLH
t
QUIET
t
t
t
SCKI
SCKIH
SSDISCKI
SCKI
SDI
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
t
t
HSDISCKI
SCKIL
DON’T CARE
S23 S22 S21 S20 S19 S18 S17 S16 S15 S14 S13 S12 S11 S10 S9 S8 S7 S6 S5 S4 S3 S2 S1 S0
SOFTSPAN CONFIGURATION WORD FOR CONVERSION N + 1
t
t
t
SKEW
DSDOBUSYL
HSDOSCKI
SCKO
SDO0
t
DSDOSCKI
DON’T CARE
DON’T CARE
D17
D17
D16 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 C2 C1 C0 SS2 SS1 SS0 D17
CONVERSION RESULT
CHANNEL 0
CHANNEL ID SOFTSPAN
CONVERSION RESULT
CHANNEL 1
24-BIT PACKET
CONVERSION N
24-BIT PACKET
CONVERSION N
SDO7
D16 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 C2 C1 C0 SS2 SS1 SS0 D17
235818 TD01
CONVERSION RESULT
CHANNEL ID SOFTSPAN
CONVERSION RESULT
CHANNEL 7
24-BIT PACKET
CONVERSION N
CHANNEL 0235818 F16
24-BIT PACKET
CONVERSION N
Figure 16. Serial CMOS I/O Mode
Serial CMOS I/O Mode
configuration words are only accepted within this recom-
mended data transaction window, but SoftSpan changes
take effect immediately with no additional analog input
settling time required before starting the next conversion.
It is still possible to read conversion data after starting the
nextconversion,butthiswilldegradeconversionaccuracy
and therefore is not recommended.
As shown in Figure 16, in CMOS I/O mode the serial data
bus consists of a serial clock input, SCKI, serial data
input, SDI, serial clock output, SCKO, and eight lanes of
serial data output, SDOꢀ to SDO7. Communication with
the LTC2358-18 across this bus occurs during predefined
data transaction windows. Within a window, the device
accepts 2ꢁ-bit SoftSpan configuration words for the next
conversion on SDI and outputs 2ꢁ-bit packets containing
conversion results and channel configuration information
from the previous conversion on SDOꢀ to SDO7. New
data transaction windows open 1ꢀms after powering up
or resetting the LTC2358-18, and at the end of each con-
version on the falling edge of BUSY. In the recommended
use case, the data transaction should be completed with
Just prior to the falling edge of BUSY and the opening of
a new data transaction window, SCKO is forced low and
SDOꢀ to SDO7 are updated with the latest conversion
results from analog input channels ꢀ to 7, respectively.
Rising edges on SCKI serially clock conversion results
and analog input channel configuration information out
on SDOꢀ to SDO7 and trigger transitions on SCKO that are
skew-matchedtothedataonSDOꢀtoSDO7. Theresulting
SCKO frequency is half that of SCKI. SCKI rising edges
also latch SoftSpan configuration words provided on SDI,
a minimum t
time of 2ꢀns prior to the start of the
QUIET
next conversion, as shown in Figure 16. New SoftSpan
235818f
30
For more information www.linear.com/LTC2358-18
LTC2358-18
APPLICATIONS INFORMATION
which are used to program the internal 2ꢁ-bit SoftSpan
configuration register. See the section Programming the
SoftSpan Configuration Register in CMOS I/O Mode for
further details. SCKI is allowed to idle either high or low
in CMOS I/O mode. As shown in Figure 17, the CMOS
bus is enabled when CS is low and is disabled and Hi-Z
when CS is high, allowing the bus to be shared across
multiple devices.
When interfacing the LTC2358-18 with a standard SPI
bus, capture output data at the receiver on rising edges of
SCKI. SCKO is not used in this case. Multiple SDO lanes
are also usually not useful in this case. In other applica-
tions, such as interfacing the LTC2358-18 with an FPGA
or CPLD, rising and falling edges of SCKO may be used
to capture serial output data on SDOꢀ to SDO7 in double
data rate (DDR) fashion. Capturing data using SCKO adds
robustnesstodelayvariationsovertemperatureandsupply.
The data on SDOꢀ to SDO7 are grouped into 2ꢁ-bit
packets consisting of an 18-bit conversion result, 3-bit
analogchannelID,and3-bitSoftSpancode,allpresented
MSB first. As suggested in Figures 16 and 17, each SDO
lane outputs these packets for all analog input channels
in a sequential, circular manner. For example, the first
2ꢁ-bit packet output on SDOꢀ corresponds to analog
input channel ꢀ, followed by the packets for channels 1
through 7. The data output on SDOꢀ then wraps back
to channel ꢀ, and this pattern repeats indefinitely. Other
SDO lanes follow a similar circular pattern, except the
first packet presented on each lane corresponds to its
associated analog input channel.
Full Eight Lane Serial CMOS Output Data Capture
As shown in Table 2, full 2ꢀꢀksps per channel throughput
canbeachievedwithaꢁ5MHzSCKIfrequencybycapturing
the first packet (2ꢁ SCKI cycles total) from all eight serial
data output lanes SDOꢀ to SDO7. This configuration also
allowsconversionresultsfromallchannelstobecaptured
using as few as 18 SCKI cycles if the 3-bit analog channel
ID and 3-bit SoftSpan code are not needed and the device
SoftSpan configuration is not being changed. Multi-lane
data capture is usually best suited for use with FPGA
or CPLD capture hardware, but may be useful in other
application-specific cases.
PD = 0
BUSY
CS
SCKI DON’T CARE
DON’T CARE
NEW SoftSpan CONFIGURATION WORD
SDI DON’T CARE
TWO ALL-ZERO WORDS AND ONE PARTIAL WORD
DON’T CARE
(OVERWRITES INTERNAL CONFIG REGISTER)
(INTERNAL CONFIG REGISTER RETAINS CURRENT VALUE)
Hi-Z
Hi-Z
SCKO
Hi-Z
Hi-Z
DIS
CHANNEL 3 PACKET
(PARTIAL)
SDO0
CHANNEL 0 PACKET
CHANNEL 7 PACKET
CHANNEL 1 PACKET
CHANNEL 0 PACKET
CHANNEL 2 PACKET
CHANNEL 1 PACKET
t
EN
t
Hi-Z
Hi-Z
CHANNEL 2 PACKET
(PARTIAL)
SDO7
235818 F17
Figure 17. Internal SoftSpan Configuration Register Behavior. Serial CMOS Bus Response to CS
235818f
31
For more information www.linear.com/LTC2358-18
LTC2358-18
APPLICATIONS INFORMATION
Fewer Than Eight Lane Serial CMOS Output Data Capture
Programming the SoftSpan Configuration Register in
CMOS I/O Mode
Applications that cannot accommodate the full eight lanes
of serial data capture may employ fewer lanes without
reconfiguring the LTC2358-18. For example, capturing
the first two packets (ꢁ8 SCKI cycles total) from SDOꢀ,
SDO2, SDOꢁ, and SDO6 provides data for analog input
channels ꢀ and 1, 2 and 3, ꢁ and 5, and 6 and 7, respec-
tively,usingfouroutputlanes.Similarly,capturingthefirst
four packets (96 SCKI cycles total) from SDOꢀ and SDOꢁ
provides data for analog input channels ꢀ to 3 and ꢁ to
7, respectively, using two output lanes. If only one lane
can be accommodated, capturing the first eight packets
(192 SCKI cycles total) from SDOꢀ provides data for all
analog input channels. As shown in Table 2, full 2ꢀꢀksps
per channel throughput can be achieved with a 9ꢀMHz
SCKI frequency in the four lane case, but the maximum
CMOS SCKI frequency of 1ꢀꢀMHz limits the throughput
to less than 2ꢀꢀksps per channel in the two lane and one
lane cases. Finally, note that in choosing the number of
lanes and which lanes to use for data capture, the user is
notrestrictedtothespecificcasesmentionedabove.Other
choices may be more optimal in particular applications.
The internal 2ꢁ-bit SoftSpan configuration register con-
trols the SoftSpan range for all analog input channels of
the LTC2358-18. The default state of this register after
power-up or resetting the device is all ones, configuring
each channel to convert in SoftSpan 7, the 2.5 • 4
REFBUF
range (see Table 1a). The state of this register may be
modifiedbyprovidinganew2ꢁ-bitSoftSpanconfiguration
word on SDI during the data transaction window shown
in Figure 16. New SoftSpan configuration words are only
accepted within this recommended data transaction win-
dow, but SoftSpan changes take effect immediately with
no additional analog input settling time required before
starting the next conversion. Setting a channel’s SoftSpan
code to SS[2:ꢀ] = ꢀꢀꢀ immediately disables the channel,
resultinginacorrespondingreductionint
onthenext
CON4
conversion.Similarly,enablingapreviouslydisabledchan-
nelrequiresnoadditionalanaloginputsettlingtimebefore
starting the next conversion. The mapping between the
serial SoftSpan configuration word, the internal SoftSpan
configuration register, and each channel’s 3-bit SoftSpan
code is illustrated in Figure 18.
Table 2. Required SCKI Frequency to Achieve Various Throughputs in Common Output Bus Configurations with Eight Channels Enabled.
Shaded Entries Denote Throughputs That Are Not Achievable in a Given Configuration. Calculated Using fSCKI = (Number of SCKI
Cycles)/(tACQ(MIN) – tQUIET
)
REQUIRED f
200ksps/CHANNEL
(tACQ = 570ns)
(MHz) TO ACHIEVE THROUGHPUT OF
SCKI
NUMBER OF SDO
LANES
NUMBER OF SCKI
CYCLES
I/O MODE
100ksps/CHANNEL
(tACQ = 5570ns)
50ksps/CHANNEL
(tACQ = 15570ns)
8
8
ꢁ
2
1
1
18
2ꢁ
35
ꢁ5
ꢁ
2
5
2
CMOS
L4DS
ꢁ8
9ꢀ
9
ꢁ
96
Not Achievable
Not Achievable
18ꢀ (36ꢀMbps)
18
35
7
13
192
96
18 (36Mbps)
7 (1ꢁMbps)
235818f
32
For more information www.linear.com/LTC2358-18
LTC2358-18
APPLICATIONS INFORMATION
CMOS I/O MODE
t
t
t
SSDISCKI
SCKI
SCKIH
SCKI
SDI
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
t
t
HSDISCKI
SCKIL
DON’T CARE
S23 S22 S21 S20 S19 S18 S17 S16 S15 S14 S13 S12 S11 S10 S9 S8 S7 S6 S5 S4 S3 S2 S1 S0
SoftSpan CONFIGURATION WORD
LVDS I/O MODE
t
t
SCKI
2
SCKIH
SCKI
(LVDS)
1
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
t
t
t
t
t
HSDISCKI
SCKIL
SSDISCKI
SSDISCKI
HSDISCKI
SDI
(LVDS)
DON’T CARE
S23 S22 S21 S20 S19 S18 S17 S16 S15 S14 S13 S12 S11 S10 S9 S8 S7 S6 S5 S4 S3 S2 S1 S0
SoftSpan CONFIGURATION WORD
INTERNAL 24-BIT SoftSpan CONFIGURATION REGISTER
(SAME FOR CMOS AND LVDS)
23
CHANNEL 7 SoftSpan CHANNEL 6 SoftSpan CHANNEL 5 SoftSpan CHANNEL 4 SoftSpan CHANNEL 3 SoftSpan CHANNEL 2 SoftSpan CHANNEL 1 SoftSpan CHANNEL 0 SoftSpan
CODE SS[2:0] CODE SS[2:0] CODE SS[2:0] CODE SS[2:0] CODE SS[2:0] CODE SS[2:0] CODE SS[2:0] CODE SS[2:0]
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
235818 F18
Figure 18. Mapping Between Serial SoftSpan Configuration Word, Internal SoftSpan
Configuration Register, and SoftSpan Code for Each Analog Input Channel
Iffewerthan2ꢁSCKIrisingedgesareprovidedduringadata
transactionwindow,thepartialwordreceivedonSDIwillbe
ignoredandtheSoftSpanconfigurationregisterwillnotbe
updated. If exactly 2ꢁ SCKI rising edges are provided, the
SoftSpan configuration register will be updated to match
the received SoftSpan configuration word, S[23:ꢀ]. The
one exception to this behavior occurs when S[23:ꢀ] is all
zeros. In this case, the SoftSpan configuration register
will not be updated, allowing applications to retain the
current SoftSpan configuration state by idling SDI low. If
more than2ꢁSCKI risingedges areprovided during a data
transaction window, each complete 2ꢁ-bit word received
onSDIwillbeinterpretedasanewSoftSpanconfiguration
word and applied to the SoftSpan configuration register
as described above. Any partial words are ignored.
After the opening of a new data transaction window at the
falling edge of BUSY, the user supplies a 2ꢁ-bit SoftSpan
configuration word on SDI during the first 2ꢁ SCKI cycles.
Thisnewwordoverwritestheinternalconfigurationregister
contentsfollowingthe2ꢁthSCKIrisingedge.Theuserthen
holds SDI low for the remainder of the data transaction
windowcausingtheregistertoretainitscontentsregardless
of the number of additional SCKI cycles applied. SoftSpan
settings may be retained across multiple conversions by
holding SDI low for the entire data transaction window,
regardless of the number of SCKI cycles applied.
Serial LVDS I/O Mode
In L4DS I/O mode, information is transmitted using posi-
+
−
tive and negative signal pairs (L4DS /L4DS ) with bits
+
−
differentially encoded as (L4DS − L4DS ). These signals
are typically routed using differential transmission lines
Typically, applications will update the SoftSpan configura-
tion register in the manner shown in Figures 16 and 17.
235818f
33
For more information www.linear.com/LTC2358-18
LTC2358-18
APPLICATIONS INFORMATION
with 1ꢀꢀΩ characteristic impedance. Logical 1’s and ꢀ’s
are nominally represented by differential +35ꢀm4 and
−35ꢀm4,respectively.Forclarity,allL4DStimingdiagrams
and interface discussions adopt the logical rather than
physical convention.
next conversion, as shown in Figure 19. New SoftSpan
configuration words are only accepted within this recom-
mended data transaction window, but SoftSpan changes
take effect immediately with no additional analog input
settling time required before starting the next conversion.
It is still possible to read conversion data after starting the
nextconversion,butthiswilldegradeconversionaccuracy
and therefore is not recommended.
As shown in Figure 19, in L4DS I/O mode the serial data
busconsistsofaserialclockdifferentialinput, SCKI, serial
data differential input, SDI, serial clock differential output,
SCKO, and serial data differential output, SDO. Communi-
cation with the LTC2358-18 across this bus occurs during
predefined data transaction windows. Within a window,
the device accepts 2ꢁ-bit SoftSpan configuration words
for the next conversion on SDI and outputs 2ꢁ-bit packets
containing conversion results and channel configuration
information from the previous conversion on SDO. New
data transaction windows open 1ꢀms after powering up
or resetting the LTC2358-18, and at the end of each con-
version on the falling edge of BUSY. In the recommended
use case, the data transaction should be completed with
Just prior to the falling edge of BUSY and the opening of
a new data transaction window, SDO is updated with the
latestconversionresultsfromanaloginputchannelꢀ.Both
rising and falling edges on SCKI serially clock conversion
resultsandanaloginputchannelconfigurationinformation
out on SDO. SCKI is also echoed on SCKO, skew-matched
tothedataonSDO.Wheneverpossible,itisrecommended
that rising and falling edges of SCKO be used to capture
DDR serial output data on SDO, as this will yield the best
robustness to delay variations over supply and tempera-
ture. SCKI rising and falling edges also latch SoftSpan
configuration words provided on SDI, which are used to
a minimum t
time of 2ꢀns prior to the start of the
QUIET
CS = PD = 0
SAMPLE N
SAMPLE N + 1
t
CYC
t
CNVH
CNV
(CMOS)
t
CNVL
BUSY
(CMOS)
t
t
CONV
ACQ
t
BUSYLH
RECOMMENDED DATA TRANSACTION WINDOW
t
t
QUIET
SCKI
t
SCKIH
SCKI
(LVDS)
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 185 186 187 188 189 190 191 192
t
t
t
t
HSDISCKI
SCKIL
SSDISCKI
HSDISCKI
t
SSDISCKI
SDI
(LVDS)
DON’T CARE
S23 S22 S21 S20 S19 S18 S17 S16 S15 S14 S13 S12 S11 S10 S9 S8 S7 S6 S5 S4 S3 S2 S1 S0
t
SoftSpan CONFIGURATION WORD FOR CONVERSION N + 1
DSDOBUSYL
t
SKEW
t
HSDOSCKI
SCKO
(LVDS)
t
DSDOSCKI
SDO
(LVDS)
DON’T CARE
D17
D16 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 C2 C1 C0 SS2 SS1 SS0 D17 D16 D15 D0 C2 C1 C0 SS2 SS1 SS0 D17
CONVERSION
RESULT
CONVERSION RESULT
CHANNEL 0
CHANNEL ID SoftSpan
CHANNEL ID SoftSpan
CHANNEL 1
CHANNEL 7
24-BIT PACKET
CHANNEL 0
24-BIT PACKET
CONVERSION N
235818 F19
24-BIT PACKET
CONVERSION N
24-BIT PACKET
CONVERSION N CONVERSION N
Figure 19. Serial LVDS I/O Mode
235818f
34
For more information www.linear.com/LTC2358-18
LTC2358-18
APPLICATIONS INFORMATION
programtheinternal2ꢁ-bitSoftSpanconfigurationregister.
See the section Programming the SoftSpan Configuration
Register in L4DS I/O Mode for further details. As shown in
Figure 2ꢀ, the L4DS bus is enabled when CS is low and is
disabled and Hi-Z when CS is high, allowing the bus to be
shared across multiple devices. Due to the high speeds
involved in L4DS signaling, L4DS bus sharing must be
carefullyconsidered.Transmissionlinelimitationsimposed
by the shared bus may limit the maximum achievable bus
clock speed. L4DS inputs are internally terminated with a
1ꢀꢀΩ differential resistor when CS is low, while outputs
must be differentially terminated with a 1ꢀꢀΩ resistor at
the receiver (FPGA). SCKI must idle in the low state in
L4DS I/O mode, including when transitioning CS.
Serial LVDS Output Data Capture
As shown in Table 2, full 2ꢀꢀksps per channel throughput
can be achieved with a 18ꢀMHz SCKI frequency by captur-
ing eight packets (96 SCKI cycles total) of DDR data from
SDO. The LTC2358-18 supports L4DS SCKI frequencies
up to 25ꢀMHz.
Programming the SoftSpan Configuration Register in
LVDS I/O Mode
The internal 2ꢁ-bit SoftSpan configuration register con-
trols the SoftSpan range for all analog input channels of
the LTC2358-18. The default state of this register after
power-up or resetting the device is all ones, configuring
each channel to convert in SoftSpan 7, the 2.5 • 4
REFBUF
The data on SDO are grouped into 2ꢁ-bit packets consist-
ing of an 18-bit conversion result, 3-bit analog channel
ID, and 3-bit SoftSpan code, all presented MSB first.
As suggested in Figures 19 and 2ꢀ, SDO outputs these
packets for all analog input channels in a sequential, cir-
cular manner. For example, the first 2ꢁ-bit packet output
on SDO corresponds to analog input channel ꢀ, followed
by the packets for channels 1 through 7. The data output
on SDO then wraps back to channel ꢀ, and this pattern
repeats indefinitely.
range (see Table 1a). The state of this register may be
modifiedbyprovidinganew2ꢁ-bitSoftSpanconfiguration
word on SDI during the data transaction window shown
in Figure 19. New SoftSpan configuration words are only
accepted within this recommended data transaction win-
dow, but SoftSpan changes take effect immediately with
no additional analog input settling time required before
starting the next conversion. Setting a channel’s SoftSpan
code to SS[2:ꢀ] = ꢀꢀꢀ immediately disables the channel,
resultinginacorrespondingreductionint
onthenext
CON4
PD = 0
BUSY
(CMOS)
CS
(CMOS)
t
EN
t
DIS
SCKI
(LVDS)
DON’T CARE
DON’T CARE
SDI
(LVDS)
NEW SoftSpan CONFIGURATION WORD
(OVERWRITES INTERNAL CONFIG REGISTER)
TWO ALL-ZERO WORDS AND ONE PARTIAL WORD
(INTERNAL CONFIG REGISTER RETAINS CURRENT VALUE)
DON’T CARE
DON’T CARE
Hi-Z
Hi-Z
SCKO
(LVDS)
Hi-Z
Hi-Z
235818 F20
CHANNEL 3 PACKET
(PARTIAL)
SDO
(LVDS)
CHANNEL 0 PACKET
CHANNEL 1 PACKET
CHANNEL 2 PACKET
Figure 20. Internal SoftSpan Configuration Register Behavior. Serial LVDS Bus Response to CS
235818f
35
For more information www.linear.com/LTC2358-18
LTC2358-18
APPLICATIONS INFORMATION
conversion.Similarly,enablingapreviouslydisabledchan-
nelrequiresnoadditionalanaloginputsettlingtimebefore
starting the next conversion. The mapping between the
serial SoftSpan configuration word, the internal SoftSpan
configuration register, and each channel’s 3-bit SoftSpan
code is illustrated in Figure 18.
complete 2ꢁ-bit word received on SDI will be interpreted
as a new SoftSpan configuration word and applied to the
SoftSpan configuration register as described above. Any
partial words are ignored.
Typically, applications will update the SoftSpan configura-
tion register in the manner shown in Figures 19 and 2ꢀ.
After the opening of a new data transaction window at
the falling edge of BUSY, the user supplies a 2ꢁ-bit DDR
SoftSpan configuration word on SDI during the first 12
SCKI cycles. This new word overwrites the internal con-
If fewer than 2ꢁ SCKI edges (rising plus falling) are
provided during a data transaction window, the partial
word received on SDI will be ignored and the SoftSpan
configuration register will not be updated. If exactly 2ꢁ
SCKI edges are provided, the SoftSpan configuration
register will be updated to match the received SoftSpan
configuration word, S[23:ꢀ]. The one exception to this
behavior occurs when S[23:ꢀ] is all zeros. In this case,
the SoftSpan configuration register will not be updated,
allowing applications to retain the current SoftSpan con-
figuration state by idling SDI low. If more than 2ꢁ SCKI
edgesareprovidedduringadatatransactionwindow,each
th
figuration register contents following the 12 SCKI falling
edge. The user then holds SDI low for the remainder of
the data transaction window causing the register to retain
its contents regardless of the number of additional SCKI
cycles applied. SoftSpan settings may be retained across
multiple conversions by holding SDI low for the entire
data transaction window, regardless of the number of
SCKI cycles applied.
BOARD LAYOUT
To obtain the best performance from the LTC2358-18, a
four-layer printed circuit board (PCB) is recommended.
Layout for the PCB should ensure the digital and analog
signal lines are separated as much as possible. In particu-
lar, care should be taken not to run any digital clocks or
signals alongside analog signals or underneath the ADC.
Also minimize the length of the REFBUF to GND (Pin 2ꢀ)
bypass capacitor return loop, and avoid routing CN4 near
signals which could potentially disturb its rising edge.
Supply bypass capacitors should be placed as close as
possible to the supply pins. Low impedance common re-
turns for these bypass capacitors are essential to the low
noise operation of the ADC. A single solid ground plane
is recommended for this purpose. When possible, screen
the analog input traces using ground.
Reference Design
For a detailed look at the reference design for this con-
verter, including schematics and PCB layout, please refer
to DC2365, the evaluation kit for the LTC2358-18.
235818f
36
For more information www.linear.com/LTC2358-18
LTC2358-18
PACKAGE DESCRIPTION
Please refer to http://www.linear.com/product/LTC23 58-18#packaging for the most recent package drawings.
LX Package
48-Lead Plastic LQFP (7mm × 7mm)
(Reference LTC DWG # 05-08-1760 Rev A)
7.15 – 7.25
5.50 REF
9.00 BSC
7.00 BSC
48
48
SEE NOTE: 4
1
2
1
2
0.50 BSC
9.00 BSC
7.00 BSC
5.50 REF
7.15 – 7.25
0.20 – 0.30
A
A
PACKAGE OUTLINE
C0.30 – 0.50
1.30 MIN
RECOMMENDED SOLDER PAD LAYOUT
APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED
1.60
1.35 – 1.45 MAX
11° – 13°
R0.08 – 0.20
GAUGE PLANE
0.25
0° – 7°
11° – 13°
1.00 REF
0.50
BSC
0.09 – 0.20
0.17 – 0.27
0.05 – 0.15
0.45 – 0.75
SECTION A – A
e 3
NOTE:
1. PACKAGE DIMENSIONS CONFORM TO JEDEC #MS-026 PACKAGE OUTLINE
2. DIMENSIONS ARE IN MILLIMETERS
3. DIMENSIONS OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.25mm ON ANY SIDE, IF PRESENT
4. PIN-1 INDENTIFIER IS A MOLDED INDENTATION, 0.50mm DIAMETER
5. DRAWING IS NOT TO SCALE
COMPONENT
PIN “A1”
LX48 LQFP 0113 REV A
TRAY PIN 1
BEVEL
PACKAGE IN TRAY LOADING ORIENTATION
235818f
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa-
37
tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.
LTC2358-18
TYPICAL APPLICATION
Amplify Differential Signals with Gain of 10
Over a Wide Common Mode Range with Buffered Analog Inputs
INTERNAL HI-Z BUFFERS
ARBITRARY
31V
ALLOW OPTIONAL
+
31V
LTC2057HV kΩ PASSIVE FILTERS
+
–
IN
24V
3.65k
0.1µF
BUFFERED
ANALOG
INPUTS
2.49k
V
+
–
CC
COMMON MODE
INPUT RANGE
IN0
IN0
549Ω
2.49k
2.2nF
GAIN = 10
LTC2358-18
3.65k
DIFFERENTIAL MODE
INPUT RANGE: 500ꢀV
–
+
V
REFBUF
47µF
REFIN
EE
0V
BW = 10kHz
–
IN
LTC2057HV
0.1µF
0.1µF
–7V
–7V
235818 TA02
ONLY CHANNEL 0 SHOWN FOR CLARITY
RELATED PARTS
PART NUMBER
ADCs
DESCRIPTION
COMMENTS
LTC2358-16
16-Bit, 2ꢀꢀksps/Ch, Buffered 8-Channel
1ꢀ.2ꢁ4 Buffered SoftSpan Inputs with 3ꢀ4 Common Mode Range,
P-P
Simultaneous Sampling, 1LSB INL, Serial ADC 9ꢁ.2dB SNR, Serial CMOS and L4DS I/O, 7mm × 7mm LQFP-ꢁ8 Package
LTC23ꢁ8-18/LTC23ꢁ8-16 18-/16-Bit, 2ꢀꢀksps/Ch, 8-Channel Simultaneous 1ꢀ.2ꢁ4 SoftSpan Inputs with Wide Common Mode Range, 97dB/9ꢁdB
Sampling, 3LSB/ 1LSB INL, Serial ADC
SNR, Serial CMOS and L4DS I/O, 7mm × 7mm LQFP-ꢁ8 Package
LTC2335-18/LTC2335-16 18-/16-Bit, 1Msps/Ch, 8-Channel Multiplexed,
3LSB/ 1LSB INL, Serial ADC
1ꢀ.2ꢁ4 SoftSpan Inputs with Wide Common Mode Range, 97dB/9ꢁdB
SNR, Serial CMOS and L4DS I/O, 7mm × 7mm LQFP-ꢁ8 Package
LTC23ꢁ5-18/LTC23ꢁ5-16 18-/16-Bit, 2ꢀꢀksps, 8-Channel Simultaneous
Sampling, 5LSB/ 1.25LSB INL, Serial ADC
ꢁ.ꢀ964 SoftSpan Inputs with Wide Common Mode Range, 92dB/91dB
SNR, Serial CMOS and L4DS I/O, 7mm × 7mm QFN-ꢁ8 Package
LTC2378-2ꢀ/LTC2377-2ꢀ/ 2ꢀ-Bit, 1Msps/5ꢀꢀksps/25ꢀksps,
2.54 Supply, 54 Fully Differential Input, 1ꢀꢁdB SNR, MSOP-16 and
ꢁmm × 3mm DFN-16 Packages
LTC2376-2ꢀ
ꢀ.5ppm INL Serial, Low Power ADC
LTC2338-18/LTC2337-18/ 18-Bit, 1Msps/5ꢀꢀksps/25ꢀksps, Serial,
LTC2336-18 Low Power ADC
LTC2328-18/LTC2327-18/ 18-Bit, 1Msps/5ꢀꢀksps/25ꢀksps, Serial,
LTC2326-18 Low Power ADC
LTC2373-18/LTC2372-18 18-Bit, 1Msps/5ꢀꢀksps, 8-Channel, Serial ADC
54 Supply, 1ꢀ.2ꢁ4 Fully Differential Input, 1ꢀꢀdB SNR, MSOP-16 Package
54 Supply, 1ꢀ.2ꢁ4 Pseudo-Differential Input, 95dB SNR,
MSOP-16 Package
54 Supply, 8 Channel Multiplexed, Configurable Input Range, 1ꢀꢀdB SNR,
DGC, 5mm × 5mm QFN-32 Package
LTC2379-18/LTC2378-18/ 18-Bit,1.6Msps/1Msps/5ꢀꢀksps/25ꢀksps, Serial, 2.54 Supply, Differential Input, 1ꢀ1.2dB SNR, 54 Input Range, DGC, Pin
LTC2377-18/LTC2376-18 Low Power ADC Compatible Family in MSOP-16 and ꢁmm × 3mm DFN-16 Packages
LTC238ꢀ-16/LTC2378-16/ 16-Bit, 2Msps/1Msps/5ꢀꢀksps/25ꢀksps, Serial, 2.54 Supply, Differential Input, 96.2dB SNR, 54 Input Range, DGC, Pin
LTC2377-16/LTC2376-16 Low Power ADC
Compatible Family in MSOP-16 and ꢁmm × 3mm DFN-16 Packages
LTC2389-18/LTC2389-16 18-Bit/16-Bit, 2.5Msps, Parallel/Serial ADC
54 Supply, Pin-Configurable Input Range, 99.8dB/96dB SNR, Parallel or
Serial I/O 7mm × 7mm LQFP-ꢁ8 and QFN-ꢁ8 Packages
LTC2387-18/LTC2387-16 18-/16-Bit, 15Msps SAR ADC
54 Supply, Differential Input, 93.8dB SNR, 5mm × 5mm QFN Package
LTC1859/LTC1858/
LTC1857
16-/1ꢁ-/12-Bit, 8-Channel, 1ꢀꢀksps, Serial ADC
1ꢀ4, SoftSpan, Single-Ended or Differential Inputs, Single 54 Supply,
SSOP-28 Package
DACs
LTC2756/LTC2757
LTC2668
18-Bit, Serial/Parallel I
SoftSpan DAC
1LSB INL/DNL, Software-Selectable Ranges,
SSOP-28/7mm × 7mm LQFP-ꢁ8 Package
OUT
16-Channel 16-/12-Bit 1ꢀ4 4
SoftSpan DACs ꢁLSB INL, Precision Reference 1ꢀppm/°C Max, 6mm × 6mm QFN-ꢁꢀ Package
OUT
References
LTC6655
LT6657
Precision Low Drift Low Noise Buffered Reference 54/2.54/2.ꢀꢁ84/1.254, 2ppm/°C, ꢀ.25ppm Peak-to-Peak Noise, MSOP-8 Package
Precision Low Drift Low Noise Buffered Reference 54/34/2.54, 1.5ppm/°C, ꢀ.5ppm Peak-to-Peak Noise, MSOP-8 Package
Amplifiers
LTC2ꢀ57/LTC2ꢀ57H4
LT6ꢀ2ꢀ
High 4oltage, Low Noise Zero-Drift Op Amp
Dual , Micropower, 54/µs, Rail-to-Rail Op Amp
Maximum Input Offset: ꢁ.5µ4, Supply 4oltage Range: ꢁ.754 to 6ꢀ4
Maximum Input Offset: 3ꢀµ4, Maximum Supply Current: 1ꢀꢀµA/Amplifier
LT135ꢁ/LT1355/LT1356
Single/Dual/Quad 1mA, 12MHz, ꢁꢀꢀ4/µs Op Amp Good DC Precision, Stable with All Capacitive Loads
235818f
LT 0317 • PRINTED IN USA
www.linear.com/LTC2358-18
38
LINEAR TECHNOLOGY CORPORATION 2017
相关型号:
LTC2358ILX-16#PBF
LTC2358-16 - Buffered Octal, 16-Bit, 200ksps/Ch Differential ±10.24V ADC with 30VP-P Common Mode Range; Package: LQFP; Pins: 48; Temperature Range: -40°C to 85°C
Linear
LTC2360CTS8#PBF
LTC2360 - 100ksps, 12-Bit Serial ADCs in TSOT-23; Package: SOT; Pins: 8; Temperature Range: 0°C to 70°C
Linear
LTC2360CTS8#TRMPBF
LTC2360 - 100ksps, 12-Bit Serial ADCs in TSOT-23; Package: SOT; Pins: 8; Temperature Range: 0°C to 70°C
Linear
LTC2360CTS8#TRPBF
LTC2360 - 100ksps, 12-Bit Serial ADCs in TSOT-23; Package: SOT; Pins: 8; Temperature Range: 0°C to 70°C
Linear
LTC2360HTS8#PBF
LTC2360 - 100ksps, 12-Bit Serial ADCs in TSOT-23; Package: SOT; Pins: 8; Temperature Range: -40°C to 125°C
Linear
©2020 ICPDF网 联系我们和版权申明