EL1526IL-T7 [INTERSIL]
Dual Channel Differential DSL Line Driver for Centillium Maximus CO Chipsets; 对胜天鲆CO芯片组的双通道差动DSL线路驱动器
| 型号： | EL1526IL-T7 |
| 厂家： | 
Intersil |
| 描述： | Dual Channel Differential DSL Line Driver for Centillium Maximus CO Chipsets |
| 文件： | 总2页 (文件大小：105K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
EL1526
®
Data Sheet
May 13, 2004
FN7405
Dual Channel Differential DSL Line Driver
for Centillium Maximus CO Chipsets
Features
• 450mA output drive capability
The EL1526 is to be used with
Centillium's Maximus CO chipset for
• 44.1V differential output drive into 100Ω
P-P
• -85dBc THD @ 1MHz 2V
very high performance ADSL
P-P
applications. The line driver supports use of ADSL
downstream spectrum up to 3.75MHz, beyond traditional
1.1MHz range. For the extended spectrum, payload rates up
to 50Mbps is achievable in conjunction of High-Bit-Loading
(HBL) feature of Maximus CO chipset. This feature allows
DMT tones to carry higher than 15 bits per tone, resulting in
higher performance ADSL services.
• High slew rate of 500V/µs
• Bandwidth - 46MHz
• Current control pins
• Channel separation
- 80dB @ 500kHz
- 75dB @ 1MHz
The EL1526 is an integral part of the signal chain for HBL.
The driver has been optimized for flat gain response and
reduced harmonic distortion and noise in the bands of
interest to improve the overall signal to noise in the system.
A unique internal compensation circuit eliminates the need
for external common mode snubber filters in active
termination applications.
Applications
• ADSL line drivers for Centillium Maximus CO chipsets
Ordering Information
PART
TAPE &
REEL
NUMBER
PACKAGE
24-Pin QFN
24-Pin QFN
24-Pin QFN
PKG. DWG. #
MDP0046
MDP0046
MDP0046
These drivers achieve a total harmonic distortion (THD)
measurement of typically -64dB @ 2.2MHz, while
consuming typically 5mA per DSL channel of total supply
current. This supply current can be set using a resistor on
EL1526IL
-
EL1526IL-T7
EL1526IL-T13
7”
13”
the I
pin. Two other pins (C & C ) can also be used to
ADJ
0 1
adjust supply current to one of four pre-set modes (full-I ,
S
3/4-I , 1/2-I , and full power-down). The EL1526 operates
on ±5V to ±12V supplies and retains its bandwidth and
linearity over the complete supply range.
S
S
Get FULL DATASHEET
The device is supplied in the small footprint (4x5mm) 24-pin
QFN package and is specified for operation over the full
-40°C to +85°C temperature range.
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1
1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2004. All Rights Reserved. Elantec is a registered trademark of Elantec Semiconductor, Inc.
All other trademarks mentioned are the property of their respective owners.
EL1526
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
2
相关型号：
©2020 ICPDF网 联系我们和版权申明