EL1526ILZ-T7 [INTERSIL]
Dual Channel Differential DSL Line Driver for Centillium Maximus CO Chipsets; 对胜天鲆CO芯片组的双通道差动DSL线路驱动器
| 型号： | EL1526ILZ-T7 |
| 厂家： | 
Intersil |
| 描述： | Dual Channel Differential DSL Line Driver for Centillium Maximus CO Chipsets |
| 文件： | 总2页 (文件大小：42K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
EL1526
®
Data Sheet
February 11, 2005
FN7405.1
Dual Channel Differential DSL Line Driver
for Centillium Maximus CO Chipsets
Features
• 450mA output drive capability
• 44.1V differential output drive into 100Ω
The EL1526 is to be used with Centillium's Maximus CO
chipset for very high performance ADSL applications. The
line driver supports use of ADSL downstream spectrum up to
3.75MHz, beyond traditional 1.1MHz range. For the
extended spectrum, payload rates up to 50Mbps is
achievable in conjunction of High-Bit-Loading (HBL) feature
of Maximus CO chipset. This feature allows DMT tones to
carry higher than 15 bits per tone, resulting in higher
performance ADSL services.
P-P
• -85dBc THD @ 1MHz 2V
P-P
• High slew rate of 500V/µs
• Bandwidth - 46MHz
• Current control pins
• Channel separation
- 80dB @ 500kHz
- 75dB @ 1MHz
The EL1526 is an integral part of the signal chain for HBL.
The driver has been optimized for flat gain response and
reduced harmonic distortion and noise in the bands of
interest to improve the overall signal to noise in the system.
A unique internal compensation circuit eliminates the need
for external common mode snubber filters in active
termination applications.
• Pb-Free available (RoHS compliant)
Applications
• ADSL line drivers for Centillium Maximus CO chipsets
Pinout
EL1526
(24-PIN QFN)
TOP VIEW
These drivers achieve a total harmonic distortion (THD)
measurement of typically -64dB @ 2.2MHz, while
consuming typically 5mA per DSL channel of total supply
current. This supply current can be set using a resistor on
the I
pin. Two other pins (C & C ) can also be used to
ADJ
0 1
adjust supply current to one of four pre-set modes (full-I ,
S
VINA+
VINB+
GND
1
2
3
4
5
6
7
19 VINA-
18 VINB-
17 VOUTB
16 VOUTC
15 VINC-
14 VIND-
13 VOUTD
3/4-I , 1/2-I , and full power-down). The EL1526 operates
S
S
on ±5V to ±12V supplies and retains its bandwidth and
linearity over the complete supply range.
The device is supplied in the small footprint (4x5mm) 24-pin
QFN package and is specified for operation over the full
-40°C to +85°C temperature range.
THERMAL
PAD
IADJ
NC
VINC+
VIND+
Ordering Information
PART
NUMBER
TAPE &
REEL
PACKAGE
24-Pin QFN
24-Pin QFN
24-Pin QFN
PKG. DWG. #
MDP0046
MDP0046
MDP0046
MDP0046
EL1526IL
-
7”
13”
-
EL1526IL-T7
EL1526IL-T13
EL1526ILZ
(See Note)
24-Pin QFN
(Pb-Free)
EL1526ILZ-T7
(See Note)
24-Pin QFN
(Pb-Free)
7”
MDP0046
MDP0046
EL1526ILZ-T13
(See Note)
24-Pin QFN
(Pb-Free)
13”
Get Full Datasheet
NOTE: Intersil Pb-free products employ special Pb-free material sets;
molding compounds/die attach materials and 100% matte tin plate
termination finish, which are RoHS compliant and compatible with both
SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed the Pb-
free requirements of IPC/JEDEC J STD-020C.
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-352-6832 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2004, 2005. All Rights Reserved
1
All other trademarks mentioned are the property of their respective owners.
EL1526
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN7405.1
February 11, 2005
2
相关型号：
©2020 ICPDF网 联系我们和版权申明