CAT706SZI-GT3 [CATALYST]
Power Supply Management Circuit, Fixed, 1 Channel, PDSO8, 3 X 3 MM, ROHS COMPLIANT, MO-187, MSOP-8;
| 型号： | CAT706SZI-GT3 |
| 厂家： | 
CATALYST SEMICONDUCTOR |
| 描述： | Power Supply Management Circuit, Fixed, 1 Channel, PDSO8, 3 X 3 MM, ROHS COMPLIANT, MO-187, MSOP-8 光电二极管 |
| 文件： | 总14页 (文件大小：230K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
CAT705, CAT706, CAT813
µP Supervisory Circuits
FEATURES
DESCRIPTION
Accurate under voltage system monitoring
The CAT705, CAT706, and CAT813 provide reset and
monitoring functions for the electronic systems. Each
device monitors the system voltage and maintains a
reset output until that voltage reaches the device’s
specified trip value and then maintains the reset
output active condition until the device’s internal timer
allows the system power supply to stabilize.
¯¯¯¯¯¯
RESET guaranteed valid for VCC = 1.0V
6µA supply current
200ms RESET pulse width
Watchdog timer function 1.6 sec timeout
Brownout detection system reset for use with
The CAT705, CAT706, and CAT813 have a watchdog
input which can be used to monitor a system signal
and cause a reset to be issued if the signal fails to
change state prior to a timeout condition.
3.0, 3.6, and 5.0 volt systems
Pin and function compatible with the
MAX705/706/813L products
Operating Range from -40°C to +85°C
¯¯¯¯¯¯
The CAT705 and CAT706 provide a manual RESET
input which initiate reset if pulled low. The CAT705,
CAT706 and CAT813 provide a RESET output which
is low for the CAT705 and CAT706, but high for the
CAT813.
Available in SOIC 8-lead and MSOP 8-lead
packages
APPLICATIONS
Microprocessor and microcontroller based
There is a secondary supply monitor included for
power-fail warning (pin PFI).
systems
Intelligent instruments
Control systems
The CAT706 has a threshold voltage 4.40V. The
CAT705/ CAT813 have a threshold voltage of 4.65V.
Critical µP monitors
Portable equipment
For Ordering Information details, see page 13.
PIN CONFIGURATION
PIN FUNCTIONS
SOIC 8-Lead
Pin Name Function
1
8
MR
WDO
¯¯¯
MR
Manual Reset input
Power Supply
VCC
GND
PFI
7
2
RESET
(RESET for CAT813)
V
CC
Ground
GND
3
4
6
5
WDI
PFO
Power Fail voltage monitor Input.
Power Fail Output
Watchdog Timer Input
PFI
¯¯¯¯
PFO
WDI
MSOP 8-Lead
CMOS Push-Pull Active Low Reset
Output (CAT705 & CAT706)
1
8
RESET
WDI
PFO
¯¯¯¯¯¯
RESET
(RESET for CAT813)
7
2
WDO
MR
CMOS Push-Pull Active High Reset
Output (CAT813)
RESET
3
4
6
5
PFI
¯¯¯¯¯
WDO
Watchdog Timer Output
GND
V
CC
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
1
Doc. No. MD-3030, Rev. A
CAT705, CAT706, CAT813
BLOCK DIAGRAM
V
CC
250µA
MR
RESET
CONTROLLER
RESET
(RESET for CAT813)
V
CC
4.65/4.40V
TIMER
WATCHDOG
TRANSITION
DETECTION
WATCHDOG
TIMER
WDI
PFI
WDO
PFO
1.25V
¯¯¯¯¯¯
RESET
¯¯¯
MR
¯¯¯¯¯
WDO
Device
RESET
WDI
PFI
CAT705
CAT706
CAT813
@ 4.65 V
@ 4.40 V
x
x
x
x
x
x
x
x
x
@ 1.25 V
@ 1.25 V
@ 1.25 V
@ 4.65 V
Doc. No. MD-3030, Rev. A
2
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT705, CAT706, CAT813
ABSOLUTE MAXIMUM RATINGS(1)
Parameters
Supply Voltage
All other pins
Ratings
Units
V
6.5
-0.3 to (VCC + 0.3)
20
V
¯¯¯¯ ¯¯¯¯
mA
Output Current RST, RST,WDO
Continuous Power Dissipations (TA = +70ºC)
SOIC 8-lead (derate 5.9mW/ºC above +70ºC)
MSOP 8-lead (derate 4.1mW/ºC above +70ºC)
Storage Temperature
mW
471
330
-65 to 150
+300
ºC
ºC
V
Lead Soldering (10 seconds max)
ESD Rating: Human Body Model
2000
ESD Rating: Machine Model
200
V
RECOMMENDED OPERATING CONDITIONS
Parameter
Range
1.2 to 5.5
Units
V
VCC (TA = -40ºC to +85ºC)
All Other Pins
-0.1 to (VCC + 0.1)
-40 to +85
V
Ambient Temperature
ºC
Notes:
(1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this
specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability.
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
3
Doc. No. MD-3030, Rev. A
CAT705, CAT706, CAT813
ELECTRICAL OPERATING CHARACTERISTICS
VCC = 4.5V to 5.5V for CAT705, CAT706, CAT813 versions;
VCC = 3.0V to 3.6V for the CAT706 R/S/T versions,
-40ºC ≤ TA ≤ +85ºC unless otherwise noted.
Typical values at TA = 25ºC and VCC = 5V for CAT705, CAT706 versions;
VCC = 3.3V for the CAT706 T/S versions; VCC = 3.0V for the CAT706 R version.(1)
Symbol Parameter
Conditions
Min
Typ
6
Max
17
Units
CAT705
CAT706
CAT813
µA
ICC
Supply Current
CAT706 (R/S/T Versions)
4
12
µA
V
CAT705 & CAT813 at
-40ºC ≤ TA ≤ +85ºC
4.50
4.65 4.75
CAT706 at -40ºC ≤ TA ≤ +85ºC
CAT706T at -40ºC ≤ TA ≤ +85ºC
CAT706S at -40ºC ≤ TA ≤ +85ºC
CAT706R at -40ºC ≤ TA ≤ +85ºC
4.25
3.00
2.85
2.55
4.40 4.50
3.08 3.15
2.93 3.00
2.63 2.70
V
V
V
V
VRST
Reset Threshold
Reset Threshold
Tempco
40
ppm/ºC
CAT705 & CAT813
CAT706
VCC to Reset Delay(2) VCC = VTH to (VTH - 100mV)
10
5
mV
mV
µs
Reset Threshold
Hysteresis
tRD
tRP
20
Reset Active
Timeout Period
140
200
400
ms
CAT705 & CAT706, VCC = VRST max
ISOURCE = -120µA
,
VCC - 1.5V
¯¯¯¯¯¯
Voltage
RESET Output High
VOH
VOL
VOH
VOL
CAT705 & CAT706, VCC = VRST max
ISOURCE = -30µA
,
0.8 x VCC
V
CAT705 & CAT706, VCC = VRST min
ISINK = 3.2mA
,
0.4
0.3
¯¯¯¯¯¯
RESET Output Low
Voltage
CAT705 &CAT706, VCC = 1.2V
ISINK = 100µA
CAT813, VCC = VRST max
ISOURCE = -120µA
,
VCC - 1.5V
RESET Output High
Voltage
V
V
CAT813, VCC = VRST max
ISOURCE = -30µA
,
0.8 x VCC
CAT813, VCC = VRST min
,
0.4
0.3
ISINK = 3.2mA
RESET Output Low
Voltage
CAT813, VCC = 1.2V
ISINK = 100µA
Notes:
(1) Over-temperature limits are guaranteed by design and not production tested.
(2) The RESET short-circuit current is the maximum pull-up current when reset is driven low by a bidirectional output.
Doc. No. MD-3030 Rev. A
4
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT705, CAT706, CAT813
ELECTRICAL OPERATING CHARACTERISTICS (continued)
CC = 4.50V to 5.5V for CAT705, CAT706 & CAT813 versions;
V
VCC = 3.0V to 3.6V for the CAT706 R/S/T version,
-40°C ≤ TA ≤ +85°C unless otherwise noted.
Typical values at TA = 25°C and VCC = 5V for CAT705, CAT706, & CAT813 versions;
VCC = 3.3V for the CAT706 T/S versions; VCC = 3.0V for the CAT706 R version.
Symbol Parameter
Conditions
Min
Typ
Max
2.25
Units
WATCHDOG INPUT (CAT705, CAT706 & CAT813)
tWD
tWDI
VIL
Watchdog Timeout Period
WDI Pulse Width
1.00
50
1.60
s
VIL = 0.4V, VIH = 0.8 x VCC
ns
0.3 x VCC
150
WDI Input Voltage(3)
WDI Input Current(4)
WDO Output Voltage
V
µA
V
VIH
0.7 x VCC
WDI = VCC, Time Average
WDI = 0V, Time Average
ISOURCE = -800µA
50
-150
-50
VCC – 1.5 VCC – 0.25
0.1
ISINK = 1.2mA
0.4
0.3 x VCC
140
MANUAL RESET INPUT(CAT705, CAT706 & CAT813)
VIL
¯¯¯
V
MR Input Voltage
VIH
0.7 x VCC
¯¯¯
¯¯¯
MR = 0V
40
1
70
µA
µs
µs
V
MR Pull-up Current
¯¯¯
tPB
MR Pulse Width
(5)
¯¯¯
tPDLY
5
MR low to Reset Delay
PFI Input Threshold
PFI Input Current
VCC = 5V
1.2
-25
1.25
0.01
1.3
25
nA
V
ISOURCE = -800µA
ISINK = 3.2mA
VCC - 1.5V
¯¯¯¯
PFO Output Voltage
0.4
V
Notes:
(3) WDI is internally serviced within the watchdog period if WDI is left open.
(4) The WDI input current is specified as an average input current when the WDI input is driven high or low. The WDI input if connected to a
three-stated output device can be disabled in the tristate mode as long as the leakage current is less than 10µA and a maximum
capacitance of less than 200pF. To clock the WDI input in the active mode the drive device must be able to source or sink at least 200µA
when active.
¯¯¯¯¯¯
(5) RESET for CAT705 & CAT706 & RESET for CAT813.
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
5
Doc. No. MD-3030, Rev. A
CAT705, CAT706, CAT813
TYPICAL ELECTRICAL OPERATING CHARACTERISTICS TABLES
Normalized Reset Threshold
Voltage vs. Temperature
VCC Supply Current vs. Temperature
9
8
7
6
5
4
3
2
1
1.06
1.04
1.02
1.00
0.98
0.96
0.94
-40 -20
0
20
40
60
80 100
-40 -20
0
20 40 60 80 100 120
TEMPERATURE (°C)
TEM PERATURE (ºC)
Doc. No. MD-3030 Rev. A
6
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT705, CAT706, CAT813
FUNCTIONAL DESCRIPTION
PROCESSOR RESET
MANUAL RESET
The CAT705, CAT706 & CAT813 each have a Manual
The CAT705, CAT706 & CAT813 detect supply
voltage (VCC) conditions that are below the specified
voltage trip value (VRST) and provide a reset output to
maintain correct system operation. On power-up,
¯¯¯
Reset (MR) input to allow for alternative control of the
¯¯¯
reset outputs. The MR input is designed for direct
¯¯¯
connection to a pushbutton (see Figure 1). The MR
¯¯¯¯¯¯
RESET (or RESET for the CAT813) are kept active for
input is internally pulled up by 52kΩ resistor and must
be pulled low to cause the reset outputs to go active.
Internally, this input is debounced and timed such that
a minimum delay tRP of 140ms after the supply voltage
(VCC) rises above VRST to allow the power supply and
processor to stabilize. When VCC drops below the
voltage trip value (VRST), the reset output signals
¯¯¯¯¯¯
RESET (or RESET) signals of at least 140ms
minimum will be generated. The min 140ms tRP delay
commences as the Manual Reset input is released
from the low level. (see Figure 2)
¯¯¯¯¯¯
¯¯¯¯¯¯
RESET (or RESET) are pulled active. RESET (or
RESET) is specifically designed to provide the reset
input signals for processors. This provides reliable
and consistent operation as power is turned on, off or
during brownout conditions by maintaining the
processor operation in known conditions.
MR
WDO
RESET/RESET
V
CC
CAT705
CAT706
CAT813
GND
PFI
WDI
PFO
Figure 1. Pushbutton RESET
t
PB
MR
t
PDLY
V
IH
V
IL
t
RP
RESET
RESET
V
V
OH
OL
Figure 2. Timing Diagram – Pushbutton RESET
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
7
Doc. No. MD-3030, Rev. A
CAT705, CAT706, CAT813
WATCHDOG TIMER
The CAT705, CAT706,
Watchdog input (WDI). The watchdog timer function
&
CAT813 provide
a
can be used to strobe the watchdog input. The most
reliable is a dedicated I/O output transitioned by a
specific software instruction.
¯¯¯¯¯¯
forces RESET (and RESET in the CAT813) signals
active when the WDI input does not have a transition
from low-to-high or high-to-low within 1.12 seconds.
The watchdog can be disabled by floating (or tri-
stating) the WDI input (see Figure 4). If the watchdog
is disabled the WDI pin will be pulled low for the first
7/8th’s of the watchdog period (tWD) and pulled high for
the last 1/8th of the watchdog period. This pulling low
of the WDI input and then high is used to detect an
open or tri-state condition and will continue to repeat
until the WDI input is driven high or low.
¯¯¯¯¯¯
Timeout of the watchdog starts when RESET (RESET
on the CAT813) becomes inactive. If a transition
occurs on the WDI input pin prior to the watchdog
time-out, the watchdog timer is reset and begins to
time-out again. If the watchdog timer is allowed to
time-out, then the reset output(s) will go active for tRP
and once released will repeat the watchdog timeout
process.
For most efficient operation of devices with the
watchdog function the WDI input should be held low
the majority of the time and only strobed high as
required to reset the watchdog timer.
Figure 3 below shows a typical implementation of a
watchdog function. Any processor signal that repeats
dependant on the normal operation of the processor
or directed by the software operating on the processor
PIC
µC
WDO
MR
DECODER
ADDRESS
MCLR
V
RESET/RESET
WDI
CC
GND
PFI
CAT705
CAT706
CAT813
PFO
Figure 3. Watchdog Timer
V
Tristate
CC
MR
WDO
V
RESET/RESET
CC
150kΩ
CAT705
CAT706
CAT813
µC
GND
PFI
WDI
PFO
OUTPUT
110kΩ
Figure 4. Watchdog Disable Circuit
Doc. No. MD-3030 Rev. A
8
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT705, CAT706, CAT813
INVALID
STROBE
VALID
STROBE
INDETERMINATE
STROBE
WDI
MIN.
t
WD
MAX.
RESET
Figure 5. Timing Diagram – Strobe Input
V
CC
V
(MAX)
RST
V
RST
V
(MIN)
RST
t
RD
RESET (CAT705 & CAT706)
V
OH
RESET Slews with V
CC
V
OL
RESET (CAT813)
Figure 6. Timing Diagram – Power Down
V
(MAX)
RST
V
RST
V
(MIN)
RST
V
CC
t
RP
RESET (CAT705 & CAT706)
V
OH
V
OL
RESET (CAT813)
Figure 7. Timing Diagram – Power Up
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
9
Doc. No. MD-3030, Rev. A
CAT705, CAT706, CAT813
APPLICATION NOTES
OUTPUT VALID CONDITIONS
¯¯¯¯¯¯
µP’s with Bidirectional Reset Pins
The RESET output uses a push-pull output which can
maintain a valid output down to a VCC of 1.0 volts. To
sink current below 0.8V a resistor can be connected
¯¯¯¯¯¯
The RESET output can be pulled low by processors
like the 68HC11 allowing for a system reset issued by
the processor. The maximum pullup current that can
be sourced by the CAT705 & CAT706 1.5mA (and by
the CAT706 T/R/S is 800µA) allowing the processor to
pull the output low even when the CAT70x is pulling it
high.
¯¯¯¯¯¯
from RESET to Ground (see Figure 8.)
This
¯¯¯¯¯¯
arrangement will maintain a valid value on the RESET
output during both power up and down but will draw
¯¯¯¯¯¯
current when the RESET output is in the high state. A
resistor value of about 100kΩ should be adequate in
most situations to maintain a low condition valid
output down to VCC equal to 1.0V.
Power Transients
Generally short duration negative-going transients of
less than 2µs on the power supply at VRST minimum
will not cause a reset condition. However the lower
the voltage of the transient the shorter the required
time to cause a reset output. These issues can
usually be remedied by the proper location of bypass
capacitance on the circuit board.
µC
MR
WDO
V
RESET/RESET
CC
GND
PFI
CAT705
CAT706
CAT813
RESET/RESET
WDI
PFO
100kΩ
¯¯¯¯¯¯
Figure 8. RESET Valid for VCC < 1.0V
5V
µC
VCC
NMI
Push Switch
MR
WDO
UNREGULATED DC
V
RESET/RESET
CC
GND
PFI
RESET/RESET
CAT705
CAT706
CAT813
WDI
PFO
I/O LINE
INTERRUPT
Figure 9. Typical Operating Circuit
Doc. No. MD-3030 Rev. A
10
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT705, CAT706, CAT813
PACKAGE OUTLINE DRAWING
(1) (2)
MSOP 8-Lead 3.0 x 3.0mm (Z)
SYMBOL
MIN
NOM
MAX
1.10
0.15
0.95
0.38
0.23
3.10
5.00
3.10
A
A1
A2
b
0.05
0.75
0.22
0.13
2.90
4.80
2.90
0.10
0.85
c
D
3.00
4.90
E
E
E1
E1
e
3.00
0.65 BSC
0.60
L
0.40
0º
0.80
6º
L1
L2
θ
0.95 REF
0.25 BSC
TOP VIEW
D
A2
A
DETAIL A
A1
e
b
c
SIDE VIEW
END VIEW
θ
L2
L
L1
DETAIL A
For current Tape and Reel information, download the PDF file from:
http://www.catsemi.com/documents/tapeandreel.pdf.
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with JEDEC MO-187
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
11
Doc. No. MD-3030, Rev. A
CAT705, CAT706, CAT813
(1) (2)
SOIC 8-Lead 150 mils (V)
SYMBOL
MIN
NOM
MAX
1.75
0.25
0.51
0.25
5.00
6.20
4.00
A
A1
b
1.35
0.10
0.33
0.19
4.80
5.80
3.80
c
E1
E
D
E
E1
e
1.27 BSC
h
0.25
0.40
0º
0.50
1.27
8º
L
PIN # 1
IDENTIFICATION
θ
TOP VIEW
D
h
A1
θ
A
c
e
b
L
SIDE VIEW
END VIEW
For current Tape and Reel information, download the PDF file from:
http://www.catsemi.com/documents/tapeandreel.pdf.
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with JEDEC MS-012.
Doc. No. MD-3030 Rev. A
12
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT705, CAT706, CAT813
EXAMPLE OF ORDERING INFORMATION(1)
Prefix
Device #
Suffix
CAT
706
R
V
I
- G
T3
Package
V: SOIC 8-Lead
Z: MSOP 8-Lead
Lead Finish
G:NiPdAu
Tape & Reel
T: Tape & Reel
3: 3000/Reel
Product
Number
705
Optional
Company ID
706
813
Reset Threshold Voltage
Blank: See Ordering Part
Number table
Temperature Range
I = Industrial (-40ºC to 85ºC)
T: 3.08V
S: 2.93V
R: 2.63V
TOP MARKING INFORMATION (FOR ALL THRESHOLDS)
NiPdAu Finish (-G)
Device #
CAT705
CAT706
CAT813
Package
MSOP
MSOP
MSOP
Top Marking
ABRT
ABRT
ABRS
ORDERING PART NUMBER
Order Part Number
CAT705VI-G
CAT705ZI-G
Threshold Voltage
4.65V
4.40V
2.63
CAT706VI-G
CAT706ZI-G
CAT706RVI-G
CAT706RZI-G
CAT706SVI-G
CAT706SZI-G
CAT706TVI-G
CAT706TZI-G
CAT813VI-G
CAT813ZI-G
2.93
3.08
4.65V
Notes:
(1) All packages are RoHS-compliant (Lead-free, Halogen-free).
(2) The standard lead finish is NiPdAu.
(3) This device used in the above example is a CAT706RVI -GT3 (2.63V, SOIC 8-Lead, Industrial Temperature, NiPdAu, Tape & Reel,
3,000/reel)
(4) Contact factory for package availability.
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
13
Doc. No. MD-3030, Rev. A
REVISION HISTORY
Date
Rev. Reason
Initial Issue
01/21/08
A
Copyrights, Trademarks and Patents
© Catalyst Semiconductor, Inc.
Trademarks and registered trademarks of Catalyst Semiconductor include each of the following:
Adaptive Analog™, Beyond Memory™, DPP™, EZDim™, LDD™, MiniPot™, Quad-Mode™ and Quantum Charge Programmable™
Catalyst Semiconductor has been issued U.S. and foreign patents and has patent applications pending that protect its products.
CATALYST SEMICONDUCTOR MAKES NO WARRANTY, REPRESENTATION OR GUARANTEE, EXPRESS OR IMPLIED, REGARDING THE SUITABILITY OF ITS
PRODUCTS FOR ANY PARTICULAR PURPOSE, NOR THAT THE USE OF ITS PRODUCTS WILL NOT INFRINGE ITS INTELLECTUAL PROPERTY RIGHTS OR THE
RIGHTS OF THIRD PARTIES WITH RESPECT TO ANY PARTICULAR USE OR APPLICATION AND SPECIFICALLY DISCLAIMS ANY AND ALL LIABILITY ARISING
OUT OF ANY SUCH USE OR APPLICATION, INCLUDING BUT NOT LIMITED TO, CONSEQUENTIAL OR INCIDENTAL DAMAGES.
Catalyst Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Catalyst Semiconductor product could create a situation where
personal injury or death may occur.
Catalyst Semiconductor reserves the right to make changes to or discontinue any product or service described herein without notice. Products with data sheets labeled
"Advance Information" or "Preliminary" and other products described herein may not be in production or offered for sale.
Catalyst Semiconductor advises customers to obtain the current version of the relevant product information before placing orders. Circuit diagrams illustrate typical
semiconductor applications and may not be complete.
Catalyst Semiconductor, Inc.
Corporate Headquarters
2975 Stender Way
Santa Clara, CA 95054
Phone: 408.542.1000
Fax: 408.542.1200
www.catsemi.com
Document No: MD-3030
Revision:
A
Issue date:
01/21/08
相关型号：
©2020 ICPDF网 联系我们和版权申明