OPA4350UA/2K5 [BB]
High-Speed, Single-Supply, Rail-to-Rail OPERATIONAL AMPLIFIERS MicroAmplifierSeries; 高速，单电源，轨至轨运算放大器MicroAmplifier ？系列
| 型号： | OPA4350UA/2K5 |
| 厂家： | 
BURR-BROWN CORPORATION |
| 描述： | High-Speed, Single-Supply, Rail-to-Rail OPERATIONAL AMPLIFIERS MicroAmplifierSeries |
| 文件： | 总24页 (文件大小：705K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
OPA350
OPA2350
OPA4350
SBOS099C − SEPTEMBER 2000 − REVISED JANUARY 2005
High-Speed, Single-Supply, Rail-to-Rail
OPERATIONAL AMPLIFIERS
MicroAmplifiertSeries
FD EATURES
DESCRIPTION
RAIL-TO-RAIL INPUT
The OPA350 series rail-to-rail CMOS operational
D
D
D
D
D
D
D
D
RAIL-TO-RAIL OUTPUT (within 10mV)
WIDE BANDWIDTH: 38MHz
HIGH SLEW RATE: 22V/µs
LOW NOISE: 5nV/√Hz
amplifiers are optimized for low voltage, single-supply
operation. Rail-to-rail input/output, low noise (5nV/√Hz),
and high speed operation (38MHz, 22V/µs) make them
ideal for driving sampling Analog-to-Digital (A/D)
converters. They are also well suited for cell phone PA
control loops and video processing (75Ω drive capability)
as well as audio and general purpose applications. Single,
dual, and quad versions have identical specifications for
maximum design flexibility.
LOW THD+NOISE: 0.0006%
UNITY-GAIN STABLE
MicroSIZE PACKAGES
SINGLE, DUAL, AND QUAD
The OPA350 series operates on a single supply as low as
2.5V with an input common-mode voltage range that
extends 300mV below ground and 300mV above the
positive supply. Output voltage swing is to within 10mV of
the supply rails with a 10kΩ load. Dual and quad designs
feature completely independent circuitry for lowest
crosstalk and freedom from interaction.
AD PPLICATIONS
CELL PHONE PA CONTROL LOOPS
D
D
D
D
D
D
D
D
DRIVING A/D CONVERTERS
VIDEO PROCESSING
DATA ACQUISITION
PROCESS CONTROL
AUDIO PROCESSING
COMMUNICATIONS
ACTIVE FILTERS
The single (OPA350) and dual (OPA2350) come in the
miniature MSOP-8 surface mount, SO-8 surface mount,
and DIP-8 packages. The quad (OPA4350) packages are
the space-saving SSOP-16 surface mount and SO-14
surface mount. All are specified from −40°C to +85°C and
operate from −55°C to +150°C.
TEST EQUIPMENT
SPICE model available at www.ti.com
OPA4350
OPA350
NC
NC
−In
+In
1
2
3
4
8
7
6
5
OPA4350
V+
Out A
−In A
+In A
+V
1
2
3
4
5
6
7
8
16 Out D
15 −In D
14 +In D
Out A
−In A
+In A
V+
1
2
3
4
5
6
7
14 Out D
13 −In D
12 +In D
11 V−
Output
NC
A
B
D
C
−
V
A
B
D
C
−
13
V
DIP−8, SO−8, MSOP−8
OPA2350
+In B
−In B
Out B
NC
12 +In C
11 −In C
10 Out C
+In B
−In B
Out B
10 +In C
Out A
−In A
+In A
−
1
2
3
4
8
V+
9
8
−In C
A
7
Out B
−In B
+In B
Out C
B
6
9
NC
5
SO−14
SSOP−16
DIP−8, SO−8, MSOP−8
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments
semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
ꢀꢁ ꢂ ꢃꢄ ꢅ ꢆꢇ ꢂꢈ ꢃ ꢉꢆꢉ ꢊꢋ ꢌꢍ ꢎ ꢏꢐ ꢑꢊꢍꢋ ꢊꢒ ꢓꢔ ꢎ ꢎ ꢕꢋꢑ ꢐꢒ ꢍꢌ ꢖꢔꢗ ꢘꢊꢓ ꢐꢑꢊ ꢍꢋ ꢙꢐ ꢑꢕꢚ ꢀꢎ ꢍꢙꢔ ꢓꢑꢒ
ꢓ ꢍꢋ ꢌꢍꢎ ꢏ ꢑꢍ ꢒ ꢖꢕ ꢓ ꢊ ꢌꢊ ꢓ ꢐ ꢑꢊ ꢍꢋꢒ ꢖ ꢕꢎ ꢑꢛꢕ ꢑꢕ ꢎ ꢏꢒ ꢍꢌ ꢆꢕꢜ ꢐꢒ ꢇꢋꢒ ꢑꢎ ꢔꢏ ꢕꢋꢑ ꢒ ꢒꢑ ꢐꢋꢙ ꢐꢎ ꢙ ꢝ ꢐꢎ ꢎ ꢐ ꢋꢑꢞꢚ
ꢀꢎ ꢍ ꢙꢔꢓ ꢑ ꢊꢍ ꢋ ꢖꢎ ꢍ ꢓ ꢕ ꢒ ꢒ ꢊꢋ ꢟ ꢙꢍ ꢕ ꢒ ꢋꢍꢑ ꢋꢕ ꢓꢕ ꢒꢒ ꢐꢎ ꢊꢘ ꢞ ꢊꢋꢓ ꢘꢔꢙ ꢕ ꢑꢕ ꢒꢑꢊ ꢋꢟ ꢍꢌ ꢐꢘ ꢘ ꢖꢐ ꢎ ꢐꢏ ꢕꢑꢕ ꢎ ꢒꢚ
Copyright 2000−2005, Texas Instruments Incorporated
www.ti.com
ꢂ
ꢂ
ꢂ
ꢀ
ꢉ
ꢠ
ꢣ
ꢤ
ꢡꢢ
ꢠꢡ
ꢠꢡ
ꢀ
ꢉ
ꢢ
ꢢ
ꢀꢉ
www.ti.com
SBOS099C − SEPTEMBER 2000 − REVISED JANUARY 2005
(1)
ELECTROSTATIC DISCHARGE SENSITIVITY
ABSOLUTE MAXIMUM RATINGS
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.0V
This integrated circuit can be damaged by ESD. Texas
Instruments recommends that all integrated circuits be
handledwith appropriate precautions. Failure to observe
(2)
Signal Input Terminals , Voltage . . . . . (V−) − 0.3V to (V+) + 0.3V
Current . . . . . . . . . . . . . . . . . . . . . . 10mA
(3)
Open Short-Circuit Current
. . . . . . . . . . . . . . . . . . . . Continuous
proper handling and installation procedures can cause damage.
Operating Temperature Range . . . . . . . . . . . . . . . −55°C to +150°C
Storage Temperature Range . . . . . . . . . . . . . . . . . −55°C to +150°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150°C
Lead Temperature (soldering, 10s) . . . . . . . . . . . . . . . . . . . . . +300°C
ESD damage can range from subtle performance degradation to
complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could
cause the device not to meet its published specifications.
(1)
Stresses above these ratings may cause permanent damage.
Exposure to absolute maximum conditions for extended periods
may degrade device reliability. These are stress ratings only, and
functional operation of the device at these or any other conditions
beyond those specified is not implied.
(2)
(3)
Input terminals are diode-clamped to the power-supply rails.
Input signals that can swing more than 0.3V beyond the supply
rails should be current limited to 10mA or less.
Short-circuit to ground, one amplifier per package.
(1)
PACKAGE/ORDERING INFORMATION
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
DESIGNATOR
PACKAGE
MARKING
ORDERING
NUMBER
TRANSPORT
MEDIA, QUANTITY
PRODUCT
SINGLE
PACKAGE-LEAD
OPA350EA/250
OPA350EA/2K5
OPA350UA
Tape and Reel, 250
Tape and Reel, 2500
Rails
OPA350EA
MSOP-8
DGK
−40°C to +85°C
C50
OPA350UA
OPA350PA
SO-8
DIP-8
D
P
−40°C to +85°C
−40°C to +85°C
OPA350UA
OPA350PA
OPA350UA/2K5
OPA350PA
Tape and Reel, 2500
Rails
DUAL
OPA2350EA/250
Tape and Reel, 250
OPA2350EA
MSOP-8
DGK
−40°C to +85°C
D50
OPA2350EA/2K5 Tape and Reel, 2500
OPA2350UA Rails
OPA2350UA/2K5 Tape and Reel, 2500
OPA2350UA
OPA2350PA
SO-8
DIP-8
D
P
−40°C to +85°C
−40°C to +85°C
OPA2350UA
OPA2350PA
OPA2350PA
Rails
QUAD
OPA4350EA/250
Tape and Reel, 250
OPA4350EA
OPA4350UA
SSOP-16
SO-14
DBQ
D
−40°C to +85°C
−40°C to +85°C
OPA4350EA
OPA4350UA
OPA4350EA/2K5 Tape and Reel, 2500
OPA4350UA Rails
OPA4350UA/2K5 Tape and Reel, 2500
(1)
For the most current package and ordering information, see the Package Option Addendum located at the end of this data sheet.
2
ꢂ
ꢂ ꢀꢉ ꢣ
ꢂ ꢀꢉ ꢤ
ꢀ
ꢉ
ꢠꢡꢢ
ꢠꢡ ꢢ
ꢠꢡ ꢢ
www.ti.com
SBOS099C − SEPTEMBER 2000 − REVISED JANUARY 2005
ELECTRICAL CHARACTERISTICS: V = 2.7V to 5.5V
S
Boldface limits apply over the temperature range, T = −40°C to +85°C. V = 5V.
A
S
All specifications at T = +25°C, R = 1kΩ connected to V /2 and V
= V /2, unless otherwise noted.
A
L
S
OUT
S
OPA350, OPA2350, OPA4350
(1)
TYP
PARAMETER
TEST CONDITIONS
MIN
MAX
UNIT
OFFSET VOLTAGE
Input Offset Voltage
= −40°C to +85°C
V
OS
V
S
= 5V
150
500
µV
mV
T
A
1
vs Temperature
vs Power-Supply Rejection Ratio
= −40°C to +85°C
T
= −40°C to +85°C
4
µV/°C
µV/V
µV/V
µV/V
A
PSRR
V
= 2.7V to 5.5V, V
= 2.7V to 5.5V, V
dc
= 0V
40
150
S
CM
T
A
V
S
= 0V
175
CM
Channel Separation (dual, quad)
INPUT BIAS CURRENT
0.15
0.5
Input Bias Current
I
B
10
pA
pA
vs Temperature
See Typical Characteristics
Input Offset Current
I
0.5
10
OS
NOISE
Input Voltage Noise, f = 100Hz to 400kHz
Input Voltage Noise Density, f = 10kHz
Input Current Noise Density, f = 100kHz
Current Noise Density, f = 10kHz
INPUT VOLTAGE RANGE
Common-Mode Voltage Range
Common-ModeRejection Ratio
4
7
5
4
µVrms
nV/√Hz
nV/√Hz
fA/√Hz
e
i
n
n
V
T
= −40°C to +85°C
−0.1
66
(V+) + 0.1
V
CM
CMRR
A
V
= 2.7V, −0.1V < V
= 5.5V, −0.1V < V
= 5.5V, −0.1V < V
< 2.8V
< 5.6V
< 5.6V
84
90
dB
dB
dB
S
S
CM
CM
CM
V
74
T
= −40°C to +85°C
V
74
A
S
INPUT IMPEDANCE
Differential
13
10 || 2.5
Ω || pF
Ω || pF
13
10 || 6.5
Common-Mode
OPEN-LOOP GAIN
Open-Loop Voltage Gain
A
OL
R
= 10kΩ, 50mV < V < (V+) −50mV
100
100
100
100
122
120
dB
dB
dB
dB
L
O
T
A
= −40°C to +85°C
R
L
= 10kW, 50mV < V < (V+) −50mV
O
R
L
= 1kΩ, 200mV < V < (V+) −200mV
O
T
A
= −40°C to +85°C
R
L
= 1kW, 200mV < V < (V+) −200mV
O
FREQUENCY RESPONSE
Gain-Bandwidth Product
Slew Rate
C
= 100pF
L
GBW
SR
G = 1
38
22
MHz
V/µs
µs
G = 1
Settling Time: 0.1%
G = 1, 2V Step
G = 1, 2V Step
0.22
0.5
0.01%
µs
Overload Recovery Time
Total Harmonic Distortion + Noise
Differential Gain Error
Differential Phase Error
V
• G = V
0.1
µs
IN
S
(2)
THD+N R = 600Ω, V = 2.5V
, G = 1, f = 1kHz
0.0006
0.17
0.17
%
L
O
PP
(3)
(3)
G = 2, R = 600Ω, V = 1.4V
%
L
O
G = 2, R = 600Ω, V = 1.4V
deg
L
O
(1)
(2)
(3)
(4)
(5)
V
V
= +5V.
S
= 0.25V to 2.75V.
OUT
NTSC signal generator used. See Figure 6 for test circuit.
Output voltage swings are measured between the output and power supply rails.
See typical characteristic curve, Output Voltage Swing vs Output Current.
3
ꢂ
ꢂ
ꢂ
ꢀ
ꢉ
ꢠ
ꢣ
ꢤ
ꢡꢢ
ꢠꢡ
ꢠꢡ
ꢀ
ꢉ
ꢢ
ꢢ
ꢀꢉ
www.ti.com
SBOS099C − SEPTEMBER 2000 − REVISED JANUARY 2005
ELECTRICAL CHARACTERISTICS: V = 2.7V to 5.5V (continued)
S
Boldface limits apply over the temperature range, T = −40°C to +85°C. V = 5V.
A
S
All specifications at T = +25°C, R = 1kΩ connected to V /2 and V
= V /2, unless otherwise noted.
A
L
S
OUT
S
OPA350, OPA2350, OPA4350
(1)
TYP
PARAMETER
TEST CONDITIONS
MIN
MAX
UNIT
OUTPUT
Voltage Output Swing from Rail
(4)
V
R
= 10kΩ, A
= 10kW, A
≥ 100dB
ꢀ 100dB
10
25
50
50
mV
mV
mV
mV
mA
mA
OUT
OUT
L
OL
T
A
= −40°C to +85°C
R
L
OL
R
= 1kΩ, A
= 1kW, A
≥ 100dB
ꢀ 100dB
200
200
L
OL
T
A
= −40°C to +85°C
R
L
OL
(5)
40
Output Current
I
Short-Circuit Current
I
80
See Typical Characteristics
SC
C
LOAD
Capacitive Load Drive
POWER SUPPLY
Operating Voltage Range
Minimum Operating Voltage
Quiescent Current (per amplifier)
V
T
A
= −40°C to +85°C
2.7
5.5
V
S
2.5
5.2
V
I
Q
I
O
I
O
= 0
= 0
7.5
mA
mA
T
= −40°C to +85°C
8.5
A
TEMPERATURE RANGE
Specified Range
−40
−55
−55
+85
+150
+150
°C
°C
°C
Operating Range
Storage Range
Thermal Resistance
MSOP-8 Surface Mount
SO-8 Surface Mount
DIP-8
q
JA
150
150
100
100
100
°C/W
°C/W
°C/W
°C/W
°C/W
SO-14 Surface Mount
SSOP-16 Surface Mount
(1)
(2)
(3)
(4)
(5)
V
V
= +5V.
S
= 0.25V to 2.75V.
OUT
NTSC signal generator used. See Figure 6 for test circuit.
Output voltage swings are measured between the output and power supply rails.
See typical characteristic curve, Output Voltage Swing vs Output Current.
4
ꢂ
ꢂ ꢀꢉ ꢣ
ꢂ ꢀꢉ ꢤ
ꢀ
ꢉ
ꢠꢡꢢ
ꢠꢡ ꢢ
ꢠꢡ ꢢ
www.ti.com
SBOS099C − SEPTEMBER 2000 − REVISED JANUARY 2005
TYPICAL CHARACTERISTICS
All specifications at T = +25°C, V = +5V, and R = 1kΩ connected to V /2, unless otherwise noted.
A
S
L
S
POWER SUPPLY AND COMMON−MODE
REJECTION RATIO vs FREQUENCY
OPEN-LOOP GAIN/PHASE vs FREQUENCY
100
90
80
70
60
50
40
30
20
10
0
160
140
120
100
80
0
−
−
−
−
PSRR
45
CMRR
(VS = +5V
−
= 0.1V to 5.1V)
φ
90
VCM
60
G
40
135
20
0
180
0.1
1
10
100
1k
10k 100k 1M 10M 100M
Frequency (Hz)
10
100
1k
10k
100k
1M
10M
Frequency (Hz)
INPUT VOLTAGE AND CURRENT NOISE
SPECTRAL DENSITY vs FREQUENCY
CHANNEL SEPARATION vs FREQUENCY
140
130
120
110
100
90
10k
1k
100k
10k
1k
Current Noise
100
10
Voltage Noise
100
10
80
1
70
Dual and quad devices.
60
0.1
1
10
100
1k
10k
100k
1M
10M
10
100
1k
10k
100k
1M
10M
Frequency (Hz)
Frequency (Hz)
TOTAL HARMONIC DISTORTION + NOISE
vs FREQUENCY
HARMONIC DISTORTION + NOISE vs FREQUENCY
1
1
G = 1
VO = 2.5VPP
RL = 600Ω
(−40dBc)
RL = 600Ω
0.1
(−60dBc)
G = 100, 3VPP (VO = 1V to 4V)
G = 10, 3VPP (VO = 1V to 4V)
0.1
0.01
0.01
( 80dBc)
−
G = 1, 3VPP (VO = 1V to 4V)
Input goes through transition region
0.001
(−100dBc)
0.001
0.0001
3rd−Harmonic
2nd−Harmonic
G = 1, 2.5VPP (VO = 0.25V to 2.75V)
Input does NOT go through transition region
0.0001
(−120dBc)
1k
10k
100k
Frequency (Hz)
1M
10
100
1k
10k
100k
Frequency (Hz)
5
ꢂ
ꢂ
ꢂ
ꢀ
ꢉ
ꢠ
ꢣ
ꢤ
ꢡꢢ
ꢠꢡ
ꢠꢡ
ꢀ
ꢉ
ꢢ
ꢢ
ꢀ
ꢉ
www.ti.com
SBOS099C − SEPTEMBER 2000 − REVISED JANUARY 2005
TYPICAL CHARACTERISTICS (continued)
All specifications at T = +25°C, V = +5V, and R = 1kΩ connected to V /2, unless otherwise noted.
A
S
L
S
OPEN−LOOP GAIN vs TEMPERATURE
DIFFERENTIAL GAIN/PHASE vs RESISTIVE LOAD
G = 2
130
125
120
115
110
0.5
0.4
0.3
0.2
0.1
0
VO = 1.4V
Phase
NTSC Signal Generator
See Figure 6 for test circuit.
Ω
RL = 1k
Ω
RL = 10k
Gain
Ω
RL = 600
−
−
−
25
75
50
0
25
50
75
100 125
0
100 200 300 400 500 600 700 800 900 1000
_
Temperature ( C)
Ω
Resistive Load (
)
SLEW RATE vs TEMPERATURE
COMMON−MODE AND POWER−SUPPLY REJECTION RATIO
vs TEMPERATURE
100
40
35
30
25
20
15
10
5
110
100
90
CMRR, VS = 5.5V
(VCM 0.1V to +5.6V)
=
−
90
80
70
60
Negative Slew Rate
Positive Slew Rate
CMRR, VS = 2.7V
(VCM = −0.1V to +2.8V)
PSRR
80
0
70
−
−
−
25
−75
−50 −25
0
25
50
75
100
125
75
50
0
25
50
75
100
125
_
Temperature (_C)
Temperature ( C)
QUIESCENT CURRENT vs SUPPLY VOLTAGE
Per Amplifier
QUIESCENT CURRENT AND
SHORT−CIRCUIT CURRENT vs TEMPERATURE
6.0
5.5
5.0
4.5
4.0
3.5
3.0
7.0
6.5
6.0
5.5
5.0
4.5
4.0
3.5
100
90
80
70
60
50
40
30
+ISC
I
−
SC
IQ
75
−
50
−
25
−
0
25
50
75
100 125
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
Temperature ( C)
_
Supply Voltage (V)
6
ꢂ
ꢂ ꢀꢉ ꢣ
ꢂ ꢀꢉ ꢤ
ꢀ
ꢉ
ꢠꢡꢢ
ꢠꢡ ꢢ
ꢠꢡ ꢢ
www.ti.com
SBOS099C − SEPTEMBER 2000 − REVISED JANUARY 2005
TYPICAL CHARACTERISTICS (continued)
All specifications at T = +25°C, V = +5V, and R = 1kΩ connected to V /2, unless otherwise noted.
A
S
L
S
INPUT BIAS CURRENT
vs INPUT COMMON−MODE VOLTAGE
INPUT BIAS CURRENT vs TEMPERATURE
1k
100
10
1.5
1.0
0.5
0.0
1
0.1
−
0.5
−
−
−
25
75
50
0
25
50
75
100
125
−0.5 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
_
Temperature ( C)
Common−Mode Voltage (V)
MAXIMUM OUTPUT VOLTAGE vs FREQUENCY
CLOSED−LOOP OUTPUT IMPEDANCE vs FREQUENCY
6
5
4
3
2
1
0
100
10
VS = 5.5V
Maximum output
voltage without
slew rate−induced
distortion.
1
G = 100
VS = 2.7V
0.1
G = 10
G = 1
0.01
0.001
0.0001
100k
1M
10M
100M
1
10
100
1k
10k 100k
1M
10M 100M
Frequency (Hz)
Frequency (Hz)
OPEN−LOOP GAIN vs OUTPUT VOLTAGE SWING
IOUT = 2.5mA
OUTPUT VOLTAGE SWING vs OUTPUT CURRENT
140
130
120
110
100
90
V+
µ
IOUT = 250 A
−
(V+) 1
_
+25 C
−
_
55 C
_
+125 C
−
(V+) 2
IOUT = 4.2mA
Depending on circuit configuration
(including closed−loop gain) performance
may be degraded in shaded region.
−
(V )+2
80
_
+25 C
−
_
_
55 C
+125 C
−
(V )+1
70
60
−
(V )
0
20
40 60 80 100 120 140 160 180 200
Output Voltage Swing from Rails (mV)
0
10
20
Output Current (mA)
30
40
7
ꢂ
ꢂ
ꢂ
ꢀ
ꢉ
ꢠ
ꢣ
ꢤ
ꢡꢢ
ꢠꢡ
ꢠꢡ
ꢀ
ꢉ
ꢢ
ꢢ
ꢀꢉ
www.ti.com
SBOS099C − SEPTEMBER 2000 − REVISED JANUARY 2005
TYPICAL CHARACTERISTICS (continued)
All specifications at T = +25°C, V = +5V, and R = 1kΩ connected to V /2, unless otherwise noted.
A
S
L
S
OFFSET VOLTAGE
PRODUCTION DISTRIBUTION
OFFSET VOLTAGE DRIFT
PRODUCTION DISTRIBUTION
18
16
14
12
10
8
20
18
16
14
12
10
8
Typical distribution of
packaged units.
Typical production
distribution of
packaged units.
6
6
4
4
2
2
0
0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
Offset Voltage Drift (µV/_C)
Offset Voltage ( V)
µ
SETTLING TIME vs CLOSED−LOOP GAIN
SMALL−SIGNAL OVERSHOOT vs LOAD CAPACITANCE
10
80
70
60
50
40
30
20
10
0
G = 1
0.01%
−
G =
1
1
G = 10
0.1%
0.1
10
100
1k
10k
100k
1M
−
−
−
100
1
10
Load Capacitance (pF)
Closed−Loop Gain (V/V)
SMALL−SIGNAL STEP RESPONSE
CL = 100pF
LARGE−SIGNAL STEP RESPONSE
CL = 100pF
100ns/div
200ns/div
8
ꢂ
ꢂ ꢀꢉ ꢣ
ꢂ ꢀꢉ ꢤ
ꢀ
ꢉ
ꢠꢡꢢ
ꢠꢡ ꢢ
ꢠꢡ ꢢ
www.ti.com
SBOS099C − SEPTEMBER 2000 − REVISED JANUARY 2005
OPERATING VOLTAGE
APPLICATIONS INFORMATION
OPA350 series op amps are fully specified from +2.7V
to +5.5V. However, supply voltage may range from
+2.5V to +5.5V. Parameters are tested over the
specified supply range—a unique feature of the
OPA350 series. In addition, many specifications apply
from −40°C to +85°C. Most behavior remains virtually
unchanged throughout the full operating voltage range.
Parameters that vary significantly with operating
voltage or temperature are shown in the typical
characteristics.
OPA350 series op amps are fabricated on a
state-of-the-art 0.6 micron CMOS process. They are
unity-gain stable and suitable for a wide range of
general-purpose applications. Rail-to-rail input/output
make them ideal for driving sampling A/D converters.
They are also well-suited for controlling the output
power in cell phones. These applications often require
high speed and low noise. In addition, the OPA350
series offers a low-cost solution for general-purpose
and consumer video applications (75Ω drive capability).
Excellent ac performance makes the OPA350 series
well-suited for audio applications. Their bandwidth,
slew rate, low noise (5nV/√Hz), low THD (0.0006%),
and small package options are ideal for these
applications. The class AB output stage is capable of
driving 600Ω loads connected to any point between V+
and ground.
RAIL-TO-RAIL INPUT
The tested input common-mode voltage range of the
OPA350 series extends 100mV beyond the supply rails.
This is achieved with a complementary input stage—an
N-channel input differential pair in parallel with a
P-channel differential pair, as shown in Figure 2. The
N-channel pair is active for input voltages close to the
positive rail, typically (V+) – 1.8V to 100mV above the
positive supply, while the P-channel pair is on for inputs
from 100mV below the negative supply to
approximately (V+) – 1.8V. There is a small transition
region, typically (V+) – 2V to (V+) – 1.6V, in which both
pairs are on. This 400mV transition region can vary
400mV with process variation. Thus, the transition
region (both input stages on) can range from (V+) –
2.4V to (V+) – 2.0V on the low end, up to (V+) – 1.6V
to (V+) – 1.2V on the high end.
Rail-to-rail input and output swing significantly
increases dynamic range, especially in low voltage
supply applications. Figure 1 shows the input and
output waveforms for the OPA350 in unity-gain
configuration. Operation is from a single +5V supply
with a 1kΩ load connected to V /2. The input is a 5V
S
PP
sinusoid. Output voltage swing is approximately
4.95V
.
PP
Power supply pins should be bypassed with 0.01µF
ceramic capacitors.
OPA350 series op amps are laser-trimmed to reduce
offset voltage difference between the N-channel and
P-channel input stages, resulting in improved
common-mode rejection and a smooth transition
between the N-channel pair and the P-channel pair.
However, within the 400mV transition region PSRR,
CMRR, offset voltage, offset drift, and THD may be
degraded compared to operation outside this region.
Ω
VS = +5, G = +1, RL = 1k
5V
VIN
A double-folded cascode adds the signal from the two
input pairs and presents a differential signal to the class
AB output stage. Normally, input bias current is
approximately 500fA. However, large inputs (greater
than 300mV beyond the supply rails) can turn on the
OPA350’s input protection diodes, causing excessive
current to flow in or out of the input pins. Momentary
voltages greater than 300mV beyond the power supply
can be tolerated if the current on the input pins is limited
to 10mA. This is easily accomplished with an input
resistor, as shown in Figure 3. Many input signals are
inherently current-limited to less than 10mA; therefore,
a limiting resistor is not required.
0
5V
VOUT
0
Figure 1. Rail-to-Rail Input and Output
9
ꢂ
ꢂ
ꢂ
ꢀ
ꢉ
ꢠ
ꢣ
ꢤ
ꢡꢢ
ꢠꢡ
ꢠꢡ
ꢀ
ꢉ
ꢢ
ꢢ
ꢀꢉ
www.ti.com
SBOS099C − SEPTEMBER 2000 − REVISED JANUARY 2005
V+
Reference
Current
VIN+
−
VIN
VBIAS1
Class AB
Control
VO
Circuitry
VBIAS2
−
V
(Ground)
Figure 2. Simplified Schematic
within a few tens of millivolts from the supply rails and
maintain high open-loop gain. See the typical
characteristics Output Voltage Swing vs Output Current
and Open-Loop Gain vs Output Voltage.
V+
CAPACITIVE LOAD AND STABILITY
IOVERLOAD
10mA max
OPA350 series op amps can drive a wide range of
capacitive loads. However, all op amps under certain
conditions may become unstable. Op amp
configuration, gain, and load value are just a few of the
factors to consider when determining stability. An op
amp in unity-gain configuration is the most susceptible
to the effects of capacitive load. The capacitive load
reacts with the op amp’s output impedance, along with
any additional load resistance, to create a pole in the
small-signal response that degrades the phase margin.
VOUT
OPAx350
VIN
Ω
5k
Figure 3. Input Current Protection for Voltages
Exceeding the Supply Voltage
In unity gain, OPA350 series op amps perform well with
very large capacitive loads. Increasing gain enhances
the amplifier’s ability to drive more capacitance. The
typical characteristic Small-Signal Overshoot vs
Capacitive Load shows performance with a 1kΩ
resistive load. Increasing load resistance improves
capacitive load drive capability.
RAIL-TO-RAIL OUTPUT
A class AB output stage with common-source
transistors is used to achieve rail-to-rail output. For light
resistive loads (>10kΩ), the output voltage swing is
typically ten millivolts from the supply rails. With heavier
resistive loads (600Ω to 10kΩ), the output can swing to
10
ꢂ
ꢂ ꢀꢉ ꢣ
ꢂ ꢀꢉ ꢤ
ꢀ
ꢉ
ꢠꢡꢢ
ꢠꢡ ꢢ
ꢠꢡ ꢢ
www.ti.com
SBOS099C − SEPTEMBER 2000 − REVISED JANUARY 2005
series provides an effective means of buffering the
A/D’s input capacitance and resulting charge injection
while providing signal gain.
FEEDBACK CAPACITOR IMPROVES
RESPONSE
For optimum settling time and stability with
high-impedance feedback networks, it may be
necessary to add a feedback capacitor across the
feedback resistor, RF, as shown in Figure 4. This
capacitor compensates for the zero created by the
feedback network impedance and the OPA350’s input
capacitance (and any parasitic layout capacitance).
The effect becomes more significant with higher
impedance networks.
Figure 5 shows the OPA350 driving an ADS7861. The
ADS7861 is a dual, 500kHz, 12-bit sampling converter
in the tiny SSOP-24 package. When used with the
miniature package options of the OPA350 series, the
combination is ideal for space-limited applications. For
further information, consult the ADS7861 data sheet
(SBAS110A).
OUTPUT IMPEDANCE
CF
The low frequency open-loop output impedance of the
OPA350’s
common-source
output
stage
is
RIN
RF
V+
approximately 1kΩ. When the op amp is connected with
feedback, this value is reduced significantly by the loop
gain of the op amp. For example, with 122dB of
open-loop gain, the output impedance is reduced in
unity-gain to less than 0.001Ω. For each decade rise in
the closed-loop gain, the loop gain is reduced by the
same amount which results in a ten-fold increase in
effective output impedance (see the typical
characteristic, Output Impedance vs Frequency).
VIN
CIN
•
•
RIN CIN = RF CF
VOUT
OPA350
CL
CIN
At higher frequencies, the output impedance will rise as
the open-loop gain of the op amp drops. However, at
these frequencies the output also becomes capacitive
due to parasitic capacitance. This prevents the output
impedance from becoming too high, which can cause
stability problems when driving capacitive loads. As
mentioned previously, the OPA350 has excellent
capacitive load drive capability for an op amp with its
bandwidth.
Where CIN is equal to the OPA350’s input
capacitance (approximately 9pF) plus any
parasitic layout capacitance.
Figure 4. Feedback Capacitor Improves Dynamic
Performance
It is suggested that a variable capacitor be used for the
feedback capacitor since input capacitance may vary
between op amps and layout capacitance is difficult to
determine. For the circuit shown in Figure 4, the value
of the variable feedback capacitor should be chosen so
that the input resistance times the input capacitance of
the OPA350 (typically 9pF) plus the estimated parasitic
layout capacitance equals the feedback capacitor times
the feedback resistor:
VIDEO LINE DRIVER
Figure 6 shows a circuit for a single supply, G = 2
composite video line driver. The synchronized outputs
of a composite video line driver extend below ground.
As shown, the input to the op amp should be ac-coupled
and shifted positively to provide adequate signal swing
to account for these negative signals in a single-supply
configuration.
RIN @ CIN + RF @ CF
where CIN is equal to the OPA350’s input capacitance
(sum of differential and common-mode) plus the layout
capacitance. The capacitor can be varied until optimum
performance is obtained.
The input is terminated with a 75Ω resistor and
ac-coupled with a 47µF capacitor to a voltage divider
that provides the dc bias point to the input. In Figure 6,
this point is approximately (V−) + 1.7V. Setting the
optimal bias point requires some understanding of the
nature of composite video signals. For best
performance, one should be careful to avoid the
distortion caused by the transition region of the
OPA350’s complementary input stage. Refer to the
discussion of rail-to-rail input.
DRIVING A/D CONVERTERS
OPA350 series op amps are optimized for driving
medium speed (up to 500kHz) sampling A/D
converters. However, they also offer excellent
performance for higher speed converters. The OPA350
11
ꢂ
ꢂ
ꢂ
ꢀ
ꢉ
ꢠ
ꢣ
ꢤ
ꢡꢢ
ꢠꢡ
ꢠꢡ
ꢀ
ꢉ
ꢢ
ꢢ
ꢀꢉ
www.ti.com
SBOS099C − SEPTEMBER 2000 − REVISED JANUARY 2005
CB1
+5V
Ω
2k
Ω
Ω
Ω
2k
2
3
4
1/ 4
1
OPA4350
VIN B1
µ
µ
0.1 F
0.1 F
CB0
24
+VD
13
+VA
Ω
2k
2k
2
3
23
22
21
20
19
18
17
16
15
14
CH B1+
SERIAL DATA A
SERIAL DATA B
BUSY
−
6
CH B1
7
4
1/ 4
CH B0+
OPA4350
5
5
VIN B0
−
CH B0
CLOCK
6
CA1
CH A1+
CS
Serial
Interface
7
ADS7861
−
CH A1
RD
CONVST
A0
Ω
2k
2k
8
CH A0+
9
−
CH A0
9
10
11
8
1/ 4
REFIN
M0
OPA4350
10
VIN A1
REFOUT
M1
CA0
DGND
AGND
12
1
Ω
2k
Ω
2k
12
13
14
1/ 4
OPA4350
VIN A0
11
VIN = 0V to 2.45V for 0V to 4.9V output.
Choose CB1, CB0, CA1, CA0 to filter high frequency noise.
Figure 5. OPA4350 Driving Sampling A/D Converter
12
ꢂ
ꢂ ꢀꢉ ꢣ
ꢂ ꢀꢉ ꢤ
ꢀ
ꢉ
ꢠꢡꢢ
ꢠꢡ ꢢ
ꢠꢡ ꢢ
www.ti.com
SBOS099C − SEPTEMBER 2000 − REVISED JANUARY 2005
RG
RF
Ω
Ω
1k
1k
+5V
C1
C4
µ
220 F
µ
0.1 F
+
µ
µ
10 F
0.1 F
2
3
7
C5
µ
1000 F
ROUT
Cable
6
VOUT
OPA350
C2
µ
47 F
RL
Video
In
4
R1
R2
Ω
75
Ω
5k
+5V (pin 7)
R3
R4
Ω
Ω
5k
5k
C3
µ
10 F
Figure 6. Single-Supply Video Line Driver
+5V
Ω
50k
(2.5V)
8
4
RG
REF1004−2.5
R1
R2
Ω
Ω
100k
25k
+5V
R3
R4
Ω
25k
Ω
100k
1/2
OPA2350
1/2
VO
OPA2350
RL
Ω
10k
Ω
200k
RG
G = 5 +
Figure 7. Two Op-Amp Instrumentation Amplifier With
Improved High Frequency Common-Mode Rejection
13
ꢂ
ꢂ
ꢂ
ꢀ
ꢉ
ꢠ
ꢣ
ꢤ
ꢡꢢ
ꢠꢡ
ꢠꢡ
ꢀ
ꢉ
ꢢ
ꢢ
ꢀꢉ
www.ti.com
SBOS099C − SEPTEMBER 2000 − REVISED JANUARY 2005
R1
10.5k
C1
4.7nF
Ω
+2.5V
+2.5V
C1
1830pF
C2
270pF
R1
2.74kΩ
R2
19.6kΩ
VOUT
OPA350
VOUT
OPA350
RL
20kΩ
VIN
RL
VIN
20kΩ
R2
49.9k
C2
1nF
Ω
−2.5V
2.5V
−
Figure 8. 10kHz Low-Pass Filter
Figure 9. 10kHz High-Pass Filter
14
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2007
PACKAGING INFORMATION
Orderable Device
OPA2350EA/250
OPA2350EA/250G4
OPA2350EA/2K5
OPA2350EA/2K5G4
OPA2350PA
Status (1)
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
Drawing
MSOP
DGK
8
250 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
MSOP
MSOP
MSOP
PDIP
DGK
DGK
DGK
P
8
250 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
8
2500 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
8
2500 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
8
50 Green (RoHS & CU NIPDAU N / A for Pkg Type
no Sb/Br)
OPA2350PAG4
OPA2350UA
PDIP
P
8
50 Green (RoHS & CU NIPDAU N / A for Pkg Type
no Sb/Br)
SOIC
SOIC
SOIC
SOIC
MSOP
MSOP
MSOP
MSOP
PDIP
D
8
100 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
OPA2350UA/2K5
OPA2350UA/2K5G4
OPA2350UAG4
OPA350EA/250
OPA350EA/250G4
OPA350EA/2K5
OPA350EA/2K5G4
OPA350PA
D
8
2500 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
D
8
2500 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
D
8
100 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
DGK
DGK
DGK
DGK
P
8
250 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
8
250 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
8
2500 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
8
2500 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
8
50 Green (RoHS & CU NIPDAU N / A for Pkg Type
no Sb/Br)
OPA350PAG4
PDIP
P
8
50 Green (RoHS & CU NIPDAU N / A for Pkg Type
no Sb/Br)
OPA350UA
SOIC
SOIC
SOIC
SOIC
D
8
100 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
OPA350UA/2K5
OPA350UA/2K5G4
OPA350UAG4
D
8
2500 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
D
8
2500 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
D
8
100 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
OPA4350EA/250
OPA4350EA/250G4
OPA4350EA/2K5
OPA4350EA/2K5G4
OPA4350UA
SSOP/
QSOP
DBQ
DBQ
DBQ
DBQ
D
16
16
16
16
14
250 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
SSOP/
QSOP
250 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
SSOP/
QSOP
2500 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
SSOP/
QSOP
2500 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
SOIC
58 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2007
Orderable Device
OPA4350UA/2K5
OPA4350UA/2K5G4
OPA4350UAG4
Status (1)
ACTIVE
ACTIVE
ACTIVE
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
Drawing
SOIC
D
14
14
14
2500 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
SOIC
SOIC
D
D
2500 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
58 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0 (mm)
B0 (mm)
K0 (mm)
P1
W
Pin1
Diameter Width
(mm) W1 (mm)
(mm) (mm) Quadrant
OPA2350EA/250
OPA2350EA/2K5
OPA2350UA/2K5
OPA350EA/250
OPA350EA/2K5
OPA350UA/2K5
OPA4350EA/250
MSOP
MSOP
SOIC
DGK
DGK
D
8
8
250
2500
2500
250
180.0
330.0
330.0
180.0
330.0
330.0
180.0
12.4
12.4
12.4
12.4
12.4
12.4
12.4
5.3
5.3
6.4
5.3
5.3
6.4
6.4
3.4
3.4
5.2
3.4
3.4
5.2
5.2
1.4
1.4
2.1
1.4
1.4
2.1
2.1
8.0
8.0
8.0
8.0
8.0
8.0
8.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
Q1
Q1
Q1
Q1
Q1
Q1
Q1
8
MSOP
MSOP
SOIC
DGK
DGK
D
8
8
2500
2500
250
8
SSOP/
QSOP
DBQ
16
OPA4350EA/2K5
OPA4350UA/2K5
SSOP/
QSOP
DBQ
D
16
14
2500
2500
330.0
330.0
12.4
16.4
6.4
6.5
5.2
9.0
2.1
2.1
8.0
8.0
12.0
16.0
Q1
Q1
SOIC
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
OPA2350EA/250
OPA2350EA/2K5
OPA2350UA/2K5
OPA350EA/250
OPA350EA/2K5
OPA350UA/2K5
OPA4350EA/250
OPA4350EA/2K5
OPA4350UA/2K5
MSOP
MSOP
DGK
DGK
D
8
8
250
2500
2500
250
184.0
346.0
346.0
184.0
346.0
346.0
190.5
346.0
346.0
184.0
346.0
346.0
184.0
346.0
346.0
212.7
346.0
346.0
50.0
29.0
29.0
50.0
29.0
29.0
31.8
29.0
33.0
SOIC
8
MSOP
DGK
DGK
D
8
MSOP
8
2500
2500
250
SOIC
8
SSOP/QSOP
SSOP/QSOP
SOIC
DBQ
DBQ
D
16
16
14
2500
2500
Pack Materials-Page 2
MECHANICAL DATA
MPDI001A – JANUARY 1995 – REVISED JUNE 1999
P (R-PDIP-T8)
PLASTIC DUAL-IN-LINE
0.400 (10,60)
0.355 (9,02)
8
5
0.260 (6,60)
0.240 (6,10)
1
4
0.070 (1,78) MAX
0.325 (8,26)
0.300 (7,62)
0.020 (0,51) MIN
0.015 (0,38)
Gage Plane
0.200 (5,08) MAX
Seating Plane
0.010 (0,25) NOM
0.125 (3,18) MIN
0.100 (2,54)
0.021 (0,53)
0.430 (10,92)
MAX
0.010 (0,25)
M
0.015 (0,38)
4040082/D 05/98
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001
For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
Logic
Military
Power Mgmt
Microcontrollers
RFID
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
RF/IF and ZigBee® Solutions www.ti.com/lprf
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明