OPA4353EA250 [TI]
High-Speed, Single-Supply, Rail-to-Rail PERATIONAL AMPLIFIERS; 高速，单电源，轨到轨放大器PERATIONAL
| 型号： | OPA4353EA250 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | High-Speed, Single-Supply, Rail-to-Rail PERATIONAL AMPLIFIERS |
| 文件： | 总26页 (文件大小：1176K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
®
OPA2353
OPA353
OPA2353
OPA4353
OPA4353
O
P
A4353
For most current data sheet and other product
information, visit www.burr-brown.com
High-Speed, Single-Supply, Rail-to-Rail
OPERATIONAL AMPLIFIERS
™
MicroAmplifier Series
APPLICATIONS
FEATURES
● CELL PHONE PA CONTROL LOOPS
● DRIVING A/D CONVERTERS
● VIDEO PROCESSING
● DATA ACQUISITION
● PROCESS CONTROL
● AUDIO PROCESSING
● COMMUNICATIONS
● RAIL-TO-RAIL INPUT
● RAIL-TO-RAIL OUTPUT (within 10mV)
● WIDE BANDWIDTH: 44MHz
● HIGH SLEW RATE: 22V/µs
● LOW NOISE: 5nV/√Hz
● LOW THD+NOISE: 0.0006%
● UNITY-GAIN STABLE
● ACTIVE FILTERS
● MicroSIZE PACKAGES
● TEST EQUIPMENT
● SINGLE, DUAL, AND QUAD
DESCRIPTION
extends 300mV beyond the supply rails. Output voltage
swing is to within 10mV of the supply rails with a 10kΩ
load. Dual and quad designs feature completely indepen-
dent circuitry for lowest crosstalk and freedom from
interaction.
OPA353 series rail-to-rail CMOS operational amplifi-
ers are designed for low cost, miniature applications.
They are optimized for low voltage, single-supply op-
eration. Rail-to-rail input/output, low noise (5nV/√Hz),
and high speed operation (44MHz, 22V/µs) make them
ideal for driving sampling analog-to-digital converters.
They are also well suited for cell phone PA control
loops and video processing (75Ω drive capability) as
well as audio and general purpose applications. Single,
dual, and quad versions have identical specifications
for design flexibility.
The single (OPA353) packages are the tiny 5-lead SOT-
23-5 surface mount and SO-8 surface mount. The dual
(OPA2353) comes in the miniature MSOP-8 surface
mount and SO-8 surface mount. The quad (OPA4353)
packages are the space-saving SSOP-16 surface mount
and SO-14 surface mount. All are specified from –40°C
to +85°C and operate from –55°C to +125°C.
The OPA353 series operates on a single supply as low as
2.5V with an input common-mode voltage range that
OPA4353
SPICE Model available at www.burr-brown.com
OPA353
Out A
–In A
+In A
+V
1
2
3
4
5
6
7
8
16 Out D
15 –In D
14 +In D
13 –V
NC
NC
–In
+In
V–
1
2
3
4
8
7
6
5
A
B
D
C
V+
Output
NC
OPA2353
+In B
–In B
Out B
NC
12 +In C
11 –In C
10 Out C
OPA353
Out A
1
2
3
4
8
7
6
5
V+
A
SO-8
–In A
+In A
V–
Out B
–In B
+In B
Out
V–
1
2
3
5
4
V+
B
9
NC
+In
–In
SSOP-16
(SO-14 package not shown)
SO-8, MSOP-8
SOT-23-5
International Airport Industrial Park
•
Mailing Address: PO Box 11400, Tucson, AZ 85734
•
Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706
• Tel: (520) 746-1111
Twx: 910-952-1111 Internet: http://www.burr-brown.com/
•
•
Cable: BBRCORP Telex: 066-6491
•
•
FAX: (520) 889-1510 Immediate Product Info: (800) 548-6132
•
© 1998 Burr-Brown Corporation
PDS-1479B
Printed in U.S.A. March, 1999
SBOS103
SPECIFICATIONS: VS = 2.7V to 5.5V
At TA = +25°C, RL = 1kΩ connected to VS/2 and VOUT = VS /2, unless otherwise noted.
Boldface limits apply over the specified temperature range, TA = –40°C to +85°C. VS = 5V.
OPA353NA, UA
OPA2353EA, UA
OPA4353EA, UA
PARAMETER
CONDITION
MIN
TYP(1)
MAX
UNITS
OFFSET VOLTAGE
Input Offset Voltage
TA = –40°C to +85°C
VOS
VS = 5V
±3
±8
±10
mV
mV
vs Temperature
vs Power Supply Rejection Ratio
TA = –40°C to +85°C
TA = –40°C to +85°C
VS = 2.7V to 5.5V, VCM = 0V
VS = 2.7V to 5.5V, VCM = 0V
dc
±5
40
µV/°C
µV/V
µV/V
µV/V
PSRR
150
175
Channel Separation (dual, quad)
0.15
INPUT BIAS CURRENT
Input Bias Current
IB
±0.5
See Typical Curve
±0.5
±10
±10
pA
pA
T
A = –40°C to +85°C
Input Offset Current
IOS
NOISE
Input Voltage Noise, f = 100Hz to 400kHz
Input Voltage Noise Density, f = 10kHz
f = 100kHz
4
7
5
4
µVrms
nV/√Hz
nV/√Hz
fA/√Hz
en
in
Current Noise Density, f = 10kHz
INPUT VOLTAGE RANGE
Common-Mode Voltage Range
Common-Mode Rejection Ratio
VCM
CMRR
–0.1
76
60
(V+) + 0.1
V
–0.1V < VCM < (V+) – 2.4V
VS = 5V, –0.1V < VCM < 5.1V
VS = 5V, –0.1V < VCM < 5.1V
86
74
dB
dB
dB
TA = –40°C to +85°C
58
INPUT IMPEDANCE
Differential
Common-Mode
1013 || 2.5
1013 || 6.5
Ω || pF
Ω || pF
OPEN-LOOP GAIN
Open-Loop Voltage Gain
TA = –40°C to +85°C
AOL
RL = 10kΩ, 50mV < VO < (V+) – 50mV
RL = 10kΩ, 50mV < VO < (V+) – 50mV
RL = 1kΩ, 200mV < VO < (V+) – 200mV
RL = 1kΩ, 200mV < VO < (V+) – 200mV
100
100
100
100
122
120
dB
dB
dB
dB
TA = –40°C to +85°C
FREQUENCY RESPONSE
Gain-Bandwidth Product
Slew Rate
Settling Time, 0.1%
0.01%
CL = 100pF
G = 1
G = 1
G = ±1, 2V Step
G = ±1, 2V Step
GBW
SR
44
22
0.22
0.5
MHz
V/µs
µs
µs
Overload Recovery Time
Total Harmonic Distortion + Noise
Differential Gain Error
Differential Phase Error
VIN • G = VS
0.1
µs
%
%
deg
THD+N
VOUT
RL = 600Ω, VO = 2.5Vp-p(2), G = 1, f = 1kHz
G = 2, RL = 600Ω, VO = 1.4V(3)
G = 2, RL = 600Ω, VO = 1.4V(3)
0.0006
0.17
0.17
OUTPUT
Voltage Output Swing from Rail(4)
TA = –40°C to +85°C
RL = 10kΩ, AOL ≥ 100dB
RL = 10kΩ, AOL ≥ 100dB
RL = 1kΩ, AOL ≥ 100dB
RL = 1kΩ, AOL ≥ 100dB
10
25
50
50
200
200
mV
mV
mV
mV
mA
mA
TA = –40°C to +85°C
Output Current
Short-Circuit Current
Capacitive Load Drive
IOUT
ISC
CLOAD
±40(5)
±80
See Typical Curve
POWER SUPPLY
Operating Voltage Range
Minimum Operating Voltage
Quiescent Current (per amplifier)
TA = –40°C to +85°C
VS
IQ
TA = –40°C to +85°C
2.7
5.5
V
V
mA
mA
2.5
5.2
IO = 0
IO = 0
8
9
TEMPERATURE RANGE
Specified Range
Operating Range
–40
–55
–55
+85
+125
+125
°C
°C
°C
Storage Range
Thermal Resistance
SOT-23-5
MSOP-8 Surface Mount
SO-8 Surface Mount
SSOP-16 Surface Mount
SO-14 Surface Mount
θJA
200
150
150
100
100
°C/W
°C/W
°C/W
°C/W
°C/W
NOTES: (1) VS = +5V. (2) VOUT = 0.25V to 2.75V. (3) NTSC signal generator used. See Figure 6 for test circuit. (4) Output voltage swings are measured between
the output and power supply rails. (5) See typical performance curve, “Output Voltage Swing vs Output Swing.”
®
2
OPA353, 2353, 4353
PIN CONFIGURATION
ELECTROSTATIC
DISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. Burr-Brown
recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
Top View
SO-14
OPA4353
Out A
–In A
+In A
V+
1
2
3
4
5
6
7
14 Out D
13 –In D
12 +In D
11 V–
A
B
D
C
ESD damage can range from subtle performance degrada-
tion to complete device failure. Precision integrated circuits
may be more susceptible to damage because very small
parametric changes could cause the device not to meet its
published specifications.
+In B
–In B
Out B
10 +In C
9
8
–In C
Out C
ABSOLUTE MAXIMUM RATINGS(1)
Supply Voltage ................................................................................... 5.5V
Signal Input Terminals, Voltage(2) .................. (V–) – 0.3V to (V+) + 0.3V
Current(2) .................................................... 10mA
Output Short-Circuit(3) .............................................................. Continuous
Operating Temperature ..................................................–55°C to +125°C
Storage Temperature .....................................................–55°C to +125°C
Junction Temperature ...................................................................... 150°C
Lead Temperature (soldering, 10s)................................................. 300°C
NOTES: (1) Stresses above these ratings may cause permanent damage.
Exposure to absolute maximum conditions for extended periods may de-
grade device reliability. (2) Input terminals are diode-clamped to the power
supply rails. Input signals that can swing more than 0.3V beyond the supply
rails should be current-limited to 10mA or less. (3) Short circuit to ground,
one amplifier per package.
PACKAGE/ORDERING INFORMATION
PACKAGE
DRAWING
NUMBER(1)
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
MARKING
ORDERING
NUMBER(2)
TRANSPORT
MEDIA
PRODUCT
PACKAGE
Single
OPA353NA
5-Lead SOT-23-5
331
"
182
"
–40°C to +85°C
D53
OPA353NA/250
OPA353NA/3K
OPA353UA
Tape and Reel
Tape and Reel
Rails
"
"
"
"
OPA353UA
SO-8 Surface Mount
–40°C to +85°C
OPA353UA
"
"
"
"
OPA353UA/2K5
Tape and Reel
Dual
OPA2353EA
MSOP-8 Surface Mount
337
"
182
"
–40°C to +85°C
E53
"
OPA2353UA
OPA2353EA/250
OPA2353EA/2K5
OPA2353UA
Tape and Reel
Tape and Reel
Rails
"
"
"
OPA2353UA
SO-8 Surface Mount
–40°C to +85°C
"
"
"
"
OPA2353UA/2K5
Tape and Reel
Quad
OPA4353EA
SSOP-16 Surface Mount
322
"
235
"
–40°C to +85°C
OPA4353EA
OPA4353EA/250
OPA4353EA/2K5
OPA4353UA
Tape and Reel
Tape and Reel
Rails
"
"
"
"
OPA4353UA
SO-14 Surface Mount
–40°C to +85°C
OPA4353UA
"
"
"
"
OPA4353UA/2K5
Tape and Reel
NOTES: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of Burr-Brown IC Data Book. (2) Models with a slash (/) are
available only in Tape and Reel in the quantities indicated (e.g., /2K5 indicates 2500 devices per reel). Ordering 2500 pieces of “OPA2353EA/2K5” will get a single
2500-piece Tape and Reel. For detailed Tape and Reel mechanical information, refer to Appendix B of Burr-Brown IC Data Book.
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility
for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or
licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support
devices and/or systems.
®
3
OPA353, 2353, 4353
TYPICAL PERFORMANCE CURVES
At TA = +25°C, VS = +5V, and RL = 1kΩ connected to VS/2, unless otherwise noted.
POWER SUPPLY AND COMMON-MODE
REJECTION RATIO vs FREQUENCY
OPEN-LOOP GAIN/PHASE vs FREQUENCY
160
140
120
100
80
0
100
90
80
70
60
50
40
30
20
10
0
PSRR
–45
–90
–135
–180
CMRR
(VS = +5V
φ
VCM = –0.1V to 5.1V)
60
G
40
20
0
0.1
1
10
100
1k
10k 100k
1M
10M 100M
10
100
1k
10k
100k
1M
10M
Frequency (Hz)
Frequency (Hz)
INPUT VOLTAGE AND CURRENT NOISE
SPECTRAL DENSITY vs FREQUENCY
CHANNEL SEPARATION vs FREQUENCY
10k
1k
100k
10k
1k
140
130
120
110
100
90
Current Noise
100
10
Voltage Noise
100
10
80
1
Dual and Quad
Versions
70
0.1
1
60
10
100
1k
10k
100k
1M
10M
10
100
1k
10k
100k
1M
10M
Frequency (Hz)
Frequency (Hz)
TOTAL HARMONIC DISTORTION + NOISE
vs FREQUENCY
HARMONIC DISTORTION + NOISE vs FREQUENCY
1
1
0.1
G = 1
VO = 2.5Vp-p
RL = 600Ω
(–40dBc)
RL = 600Ω
0.1
(–60dBc)
G = 100, 3Vp-p (VO = 1V to 4V)
G = 10, 3Vp-p (VO = 1V to 4V)
0.01
(–80dBc)
0.01
G = 1, 3Vp-p (VO = 1V to 4V)
Input goes through transition region
0.001
(–100dBc)
0.001
0.0001
3rd Harmonic
2nd Harmonic
G = 1, 2.5Vp-p (VO = 0.25V to 2.75V)
Input does NOT go through transition region
0.0001
(–120dBc)
1k
10k
100k
Frequency (Hz)
1M
10
100
1k
10k
100k
Frequency (Hz)
®
4
OPA353, 2353, 4353
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C, VS = +5V, and RL = 1kΩ connected to VS/2, unless otherwise noted.
OPEN-LOOP GAIN vs TEMPERATURE
DIFFERENTIAL GAIN/PHASE vs RESISTIVE LOAD
130
125
120
115
110
0.5
0.4
0.3
0.2
0.1
0
G = 2
V
O = 1.4V
Phase
NTSC Signal Generator
See Figure 6 for test circuit.
RL = 1kΩ
RL = 10kΩ
Gain
RL = 600Ω
–75
–50 –25
0
25
50
75
100 125
0
100 200 300 400 500 600 700 800 900 1000
Temperature (°C)
Resistive Load (Ω)
COMMON-MODE AND POWER SUPPLY
REJECTION RATIO vs TEMPERATURE
SLEW RATE vs TEMPERATURE
90
80
70
60
50
110
40
35
30
25
20
15
10
5
CMRR, VS = 5V
(VCM = –0.1V to +5.1V)
100
90
Negative Slew Rate
Positive Slew Rate
PSRR
80
70
0
–75
–50
–25
0
25
50
75
100
125
–75
–50
–25
0
25
50
75
100
125
Temperature (°C)
Temperature (°C)
QUIESCENT CURRENT AND
SHORT-CIRCUIT CURRENT vs TEMPERATURE
QUIESCENT CURRENT vs SUPPLY VOLTAGE
Per Amplifier
7.0
6.5
6.0
5.5
5.0
4.5
4.0
3.5
100
90
80
70
60
50
40
30
6.0
5.5
5.0
4.5
4.0
3.5
3.0
+ISC
–ISC
IQ
–75
–50
–25
0
25
50
75
100
125
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
Temperature (°C)
Supply Voltage (V)
®
5
OPA353, 2353, 4353
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C, VS = +5V, and RL = 1kΩ connected to VS/2, unless otherwise noted.
INPUT BIAS CURRENT
INPUT BIAS CURRENT vs TEMPERATURE
vs INPUT COMMON-MODE VOLTAGE
1k
100
10
1.5
1.0
0.5
1
0.0
0.1
–0.5
–75
–50
–25
0
25
50
75
100
125
–0.5 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
Temperature (°C)
Common-Mode Voltage (V)
MAXIMUM OUTPUT VOLTAGE vs FREQUENCY
CLOSED-LOOP OUTPUT IMPEDANCE vs FREQUENCY
6
100
10
VS = 5.5V
Maximum output
voltage without
slew rate-induced
distortion.
5
4
3
2
1
0
1
G = 100
VS = 2.7V
0.1
G = 10
G = 1
0.01
0.001
0.0001
1
10
100
1k
10k 100k
1M
10M 100M
100k
1M
10M
100M
Frequency (Hz)
Frequency (Hz)
OUTPUT VOLTAGE SWING vs OUTPUT CURRENT
OPEN-LOOP GAIN vs OUTPUT VOLTAGE SWING
IOUT = 250µA
IOUT = 2.5mA
V+
(V+)–1
(V+)–2
(V–)+2
(V–)+1
(V–)
140
130
120
110
100
90
+25°C
–55°C
+125°C
Depending on circuit configuration
(including closed-loop gain) performance
may be degraded in shaded region.
IOUT = 4.2mA
+25°C
–55°C
80
+125°C
70
60
0
±10
±20
Output Current (mA)
±30
±40
0
20
40
60
80 100 120 140 160 180 200
Output Voltage Swing from Supply Rails (mV)
®
6
OPA353, 2353, 4353
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C, VS = +5V, and RL = 1kΩ connected to VS/2, unless otherwise noted.
OFFSET VOLTAGE DRIFT
PRODUCTION DISTRIBUTION
OFFSET VOLTAGE PRODUCTION DISTRIBUTION
35
30
25
20
15
10
5
25
20
15
10
5
Typical production
distribution of
packaged units.
Typical production
distribution of
packaged units.
0
0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
–8 –7 –6 –5
4
–3 –2 –1
0
1
2
3
4
5
6
7 8
Offset Voltage Drift (µV/°C)
Offset Voltage (mV)
SETTLING TIME vs CLOSED-LOOP GAIN
SMALL-SIGNAL OVERSHOOT vs LOAD CAPACITANCE
10
80
70
60
50
40
30
20
10
0
G = 1
0.01%
G = –1
1
G = ±10
0.1%
0.1
10
100
1k
10k
100k
1M
±1
±10
±100
Load Capacitance (pF)
Closed-Loop Gain (V/V)
LARGE-SIGNAL STEP RESPONSE
CL = 100pF
SMALL-SIGNAL STEP RESPONSE
CL = 100pF
200ns/div
100ns/div
®
7
OPA353, 2353, 4353
the OPA353 in unity-gain configuration. Operation is
from a single +5V supply with a 1kΩ load connected to
VS /2. The input is a 5Vp-p sinusoid. Output voltage is
approximately 4.95Vp-p.
APPLICATIONS INFORMATION
OPA353 series op amps are fabricated on a state-of-the-art
0.6 micron CMOS process. They are unity-gain stable and
suitable for a wide range of general purpose applications.
Rail-to-rail input/output make them ideal for driving sam-
pling A/D converters. They are well suited for controlling
the output power in cell phones. These applications often
require high speed and low noise. In addition, the OPA353
series offers a low cost solution for general purpose and
consumer video applications (75Ω drive capability).
Power supply pins should be bypassed with 0.01µF ceramic
capacitors.
OPERATING VOLTAGE
OPA353 series op amps are fully specified from +2.7V to
+5.5V. However, supply voltage may range from +2.5V to
+5.5V. Parameters are guaranteed over the specified supply
range—a unique feature of the OPA353 series. In addition,
many specifications apply from –40°C to +85°C. Most
behavior remains virtually unchanged throughout the full
operating voltage range. Parameters which vary signifi-
cantly with operating voltages or temperature are shown in
the typical performance curves.
Excellent ac performance makes the OPA353 series well
suited for audio applications. Their bandwidth, slew rate,
low noise (5nV/√Hz), low THD (0.0006%), and small pack-
age options are ideal for these applications. The class AB
output stage is capable of driving 600Ω loads connected to
any point between V+ and ground.
Rail-to-rail input and output swing significantly increases
dynamic range, especially in low voltage supply applica-
tions. Figure 1 shows the input and output waveforms for
RAIL-TO-RAIL INPUT
The guaranteed input common-mode voltage range of the
OPA353 series extends 100mV beyond the supply rails. This
is achieved with a complementary input stage—an
N-channel input differential pair in parallel with a P-channel
differential pair (see Figure 2). The N-channel pair is active
for input voltages close to the positive rail, typically
(V+) – 1.8V to 100mV above the positive supply, while the
P-channel pair is on for inputs from 100mV below the
negative supply to approximately (V+) – 1.8V. There is a
small transition region, typically (V+) – 2V to (V+) – 1.6V, in
which both pairs are on. This 400mV transition region can
vary ±400mV with process variation. Thus, the transition
region (both input stages on) can range from (V+) – 2.4V to
(V+) – 2.0V on the low end, up to (V+) – 1.6V to (V+) – 1.2V
on the high end.
VS = +5, G = +1, RL = 1kΩ
5V
VIN
0
5V
VOUT
0
FIGURE 1. Rail-to-Rail Input and Output.
V+
Reference
Current
VIN+
VIN–
VBIAS1
Class AB
Control
VO
Circuitry
VBIAS2
V–
(Ground)
FIGURE 2. Simplified Schematic.
®
8
OPA353, 2353, 4353
A double-folded cascode adds the signal from the two input
pairs and presents a differential signal to the class AB output
stage. Normally, input bias current is approximately 500fA.
However, large inputs (greater than 300mV beyond the
supply rails) can turn on the OPA353’s input protection
diodes, causing excessive current to flow in or out of the
input pins. Momentary voltages greater than 300mV beyond
the power supply can be tolerated if the current on the input
pins is limited to 10mA. This is easily accomplished with an
input resistor as shown in Figure 3. Many input signals are
inherently current-limited to less than 10mA, therefore, a
limiting resistor is not required.
FEEDBACK CAPACITOR IMPROVES RESPONSE
For optimum settling time and stability with high-imped-
ance feedback networks, it may be necessary to add a
feedback capacitor across the feedback resistor, RF, as
shown in Figure 4. This capacitor compensates for the zero
created by the feedback network impedance and the
OPA353’s input capacitance (and any parasitic layout
capacitance). The effect becomes more significant with
higher impedance networks.
CF
RIN
RF
V+
VIN
V+
IOVERLOAD
10mA max
CIN
OPA353
CIN
VOUT
OPAx353
RIN • CIN = RF • CF
VIN
VOUT
5kΩ
CL
Where CIN is equal to the OPA353’s input
capacitance (approximately 9pF) plus any
parastic layout capacitance.
FIGURE 3. Input Current Protection for Voltages Exceeding
the Supply Voltage.
RAIL-TO-RAIL OUTPUT
FIGURE 4. Feedback Capacitor Improves Dynamic Perfor-
mance.
A class AB output stage with common-source transistors is
used to achieve rail-to-rail output. For light resistive loads
(>10kΩ), the output voltage swing is typically ten millivolts
from the supply rails. With heavier resistive loads (600Ω to
10kΩ), the output can swing to within a few tens of milli-
volts from the supply rails and maintain high open-loop
gain. See the typical performance curves “Output Voltage
Swing vs Output Current” and “Open-Loop Gain vs Output
Voltage.”
It is suggested that a variable capacitor be used for the
feedback capacitor since input capacitance may vary be-
tween op amps and layout capacitance is difficult to
determine. For the circuit shown in Figure 4, the value of
the variable feedback capacitor should be chosen so that
the input resistance times the input capacitance of the
OPA353 (typically 9pF) plus the estimated parasitic layout
capacitance equals the feedback capacitor times the feed-
back resistor:
CAPACITIVE LOAD AND STABILITY
RIN • CIN = RF • CF
OPA353 series op amps can drive a wide range of capacitive
loads. However, all op amps under certain conditions may
become unstable. Op amp configuration, gain, and load
value are just a few of the factors to consider when determin-
ing stability. An op amp in unity gain configuration is the
most susceptible to the effects of capacitive load. The
capacitive load reacts with the op amp’s output impedance,
along with any additional load resistance, to create a pole in
the small-signal response which degrades the phase margin.
where CIN is equal to the OPA353’s input capacitance
(sum of differential and common-mode) plus the layout
capacitance. The capacitor can be varied until optimum
performance is obtained.
DRIVING A/D CONVERTERS
OPA353 series op amps are optimized for driving medium
speed (up to 500kHz) sampling A/D converters. However,
they also offer excellent performance for higher speed
converters. The OPA353 series provides an effective means
of buffering the A/D’s input capacitance and resulting
charge injection while providing signal gain. For applica-
tions requiring high accuracy, the OPA350 series is recom-
mended.
In unity gain, OPA353 series op amps perform well with
large capacitive loads. Increasing gain enhances the
amplifier’s ability to drive more capacitance. The typical
performance curve “Small-Signal Overshoot vs Capacitive
Load” shows performance with a 1kΩ resistive load. In-
creasing load resistance improves capacitive load drive ca-
pability.
®
9
OPA353, 2353, 4353
Figure 5 shows the OPA353 driving an ADS7861. The
ADS7861 is a dual, 12-bit, 500kHz sampling converter in
the small SSOP-24 package. When used with the miniature
package options of the OPA353 series, the combination is
ideal for space-limited and low power applications. For
further information consult the ADS7861 data sheet.
from becoming too high, which can cause stability prob-
lems when driving capacitive loads. As mentioned previ-
ously, the OPA353 has excellent capacitive load drive
capability for an op amp with its bandwidth.
VIDEO LINE DRIVER
Figure 6 shows a circuit for a single supply, G = 2 com-
posite video line driver. The synchronized outputs of a
composite video line driver extend below ground. As
shown, the input to the op amp should be ac-coupled and
shifted positively to provide adequate signal swing to
account for these negative signals in a single-supply con-
figuration.
OUTPUT IMPEDANCE
The low frequency open-loop output impedance of the
OPA353’s common-source output stage is approximately
1kΩ. When the op amp is connected with feedback, this
value is reduced significantly by the loop gain of the op
amp. For example, with 122dB of open-loop gain, the
output impedance is reduced in unity-gain to less than
0.001Ω. For each decade rise in the closed-loop gain, the
loop gain is reduced by the same amount which results in
a ten-fold increase in output impedance (see the typical
performance curve, “Output Impedance vs Frequency”).
The input is terminated with a 75Ω resistor and ac-coupled
with a 47µF capacitor to a voltage divider that provides the
dc bias point to the input. In Figure 6, this point is
approximately (V–) + 1.7V. Setting the optimal bias point
requires some understanding of the nature of composite
video signals. For best performance, one should be careful
to avoid the distortion caused by the transition region of
the OPA353’s complementary input stage. Refer to the
discussion of rail-to-rail input.
At higher frequencies, the output impedance will rise as
the open-loop gain of the op amp drops. However, at these
frequencies the output also becomes capacitive due to
parasitic capacitance. This prevents the output impedance
CB1
+5V
2kΩ
2kΩ
2
3
4
1/4
OPA4353
VIN B1
0.1µF
0.1µF
CB0
24
+VD
13
+VA
2kΩ
2kΩ
2
3
23
22
21
20
19
18
17
16
15
14
CH B1+
CH B1–
CH B0+
CH B0–
CH A1+
CH A1–
CH A0+
CH A0–
REFIN
Serial Data A
Serial Data B
BUSY
6
7
1/4
OPA4353
4
5
5
VIN B0
CLOCK
6
CA1
CS
Serial
Interface
ADS7861
7
RD
CONVST
A0
2kΩ
2kΩ
8
9
9
10
11
8
1/4
OPA4353
M0
10
VIN A1
REFOUT
M1
CA0
DGND
1
AGND
12
2kΩ
2kΩ
14
1/4
OPA4353
VIN A0
11
VIN = 0V to 2.45V for 0V to 4.9V output.
Choose CB1, CB0, CA1, CA0 to filter high frequency noise.
FIGURE 5. OPA4353 Driving Sampling A/D Converter.
®
10
OPA353, 2353, 4353
RG
RF
1kΩ
1kΩ
C4
0.1µF
+5V
C1
220µF
+
0.1µF
10µF
7
C5
1000µF
ROUT
Cable
6
C2
47µF
VOUT
OPA353
Video
In
RL
R1
75Ω
R2
5kΩ
4
+5V (pin 7)
R3
5kΩ
R4
5kΩ
C3
10µF
FIGURE 6. Single-Supply Video Line Driver.
+5V
50kΩ
(2.5V)
8
RG
REF1004-2.5
R1
100kΩ
R2
25kΩ
4
+5V
R3
R4
25kΩ
100kΩ
1/2
OPA2353
1/2
OPA2353
VOUT
RL
10kΩ
200kΩ
G = 5 +
RG
FIGURE 7. Two Op-Amp Instrumentation Amplifier With Improved High Frequency Common-Mode Rejection.
<1pF (prevents gain peaking)
R1
10.5kΩ
10MΩ
+V
+2.5V
λ
VO
OPA353
C1
C2
1830pF
270pF
VOUT
OPA353
VIN
RL
20kΩ
FIGURE 8. Transimpedance Amplifier.
R2
49.9kΩ
–2.5V
C1
4.7µF
+2.5V
FIGURE 10. 10kHz High-Pass Filter.
R1
2.74kΩ
R2
19.6kΩ
VOUT
OPA353
RL
VIN
20kΩ
C2
1nF
–2.5V
FIGURE 9. 10kHz Low-Pass Filter.
®
11
OPA353, 2353, 4353
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
PACKAGING INFORMATION
Orderable Device
OPA2353EA/250
OPA2353EA/250G4
OPA2353EA/2K5
OPA2353EA/2K5G4
OPA2353UA
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
Top-Side Markings
Samples
Drawing
Qty
(1)
(2)
(3)
(4)
ACTIVE
VSSOP
VSSOP
VSSOP
VSSOP
SOIC
DGK
8
8
8
8
8
8
8
8
5
5
5
5
8
8
8
8
16
250
Green (RoHS CU NIPDAUAG Level-2-260C-1 YEAR
& no Sb/Br)
E53
E53
E53
E53
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
DGK
DGK
DGK
D
250
2500
2500
75
Green (RoHS CU NIPDAUAG Level-2-260C-1 YEAR
& no Sb/Br)
Green (RoHS CU NIPDAUAG Level-2-260C-1 YEAR
& no Sb/Br)
Green (RoHS CU NIPDAUAG Level-2-260C-1 YEAR
& no Sb/Br)
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
OPA
2353UA
OPA2353UA/2K5
OPA2353UA/2K5G4
OPA2353UAG4
OPA353NA/250
OPA353NA/250G4
OPA353NA/3K
SOIC
D
2500
2500
75
Green (RoHS
& no Sb/Br)
OPA
2353UA
SOIC
D
Green (RoHS
& no Sb/Br)
OPA
2353UA
SOIC
D
Green (RoHS
& no Sb/Br)
OPA
2353UA
SOT-23
SOT-23
SOT-23
SOT-23
SOIC
DBV
DBV
DBV
DBV
D
250
250
3000
3000
75
Green (RoHS
& no Sb/Br)
D53
D53
D53
D53
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
OPA353NA/3KG4
OPA353UA
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
OPA
353UA
OPA353UA/2K5
OPA353UA/2K5G4
OPA353UAG4
SOIC
D
2500
2500
75
Green (RoHS
& no Sb/Br)
OPA
353UA
SOIC
D
Green (RoHS
& no Sb/Br)
OPA
353UA
SOIC
D
Green (RoHS
& no Sb/Br)
OPA
353UA
OPA4353EA/250
SSOP
DBQ
250
Green (RoHS
& no Sb/Br)
OPA
4353EA
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
Orderable Device
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
Samples
Drawing
Qty
(1)
(2)
(3)
(4)
OPA4353EA/250G4
OPA4353EA/2K5
OPA4353EA/2K5G4
OPA4353UA
ACTIVE
SSOP
SSOP
SSOP
SOIC
SOIC
SOIC
SOIC
DBQ
16
16
16
14
14
14
14
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
-40 to 85
OPA
4353EA
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
DBQ
DBQ
D
2500
2500
50
Green (RoHS
& no Sb/Br)
OPA
4353EA
Green (RoHS
& no Sb/Br)
OPA
4353EA
Green (RoHS
& no Sb/Br)
OPA4353UA
OPA4353UA
OPA4353UA
OPA4353UA
OPA4353UA/2K5
OPA4353UA/2K5G4
OPA4353UAG4
D
2500
2500
50
Green (RoHS
& no Sb/Br)
-40 to 85
-40 to 85
D
Green (RoHS
& no Sb/Br)
D
Green (RoHS
& no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
24-Jul-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
OPA2353EA/250
OPA2353EA/2K5
OPA2353UA/2K5
OPA353UA/2K5
OPA4353EA/250
OPA4353EA/2K5
OPA4353UA/2K5
VSSOP
VSSOP
SOIC
DGK
DGK
D
8
8
250
2500
2500
2500
250
180.0
330.0
330.0
330.0
180.0
330.0
330.0
12.4
12.4
12.4
12.4
12.4
12.4
16.4
5.3
5.3
6.4
6.4
6.4
6.4
6.5
3.4
3.4
5.2
5.2
5.2
5.2
9.0
1.4
1.4
2.1
2.1
2.1
2.1
2.1
8.0
8.0
8.0
8.0
8.0
8.0
8.0
12.0
12.0
12.0
12.0
12.0
12.0
16.0
Q1
Q1
Q1
Q1
Q1
Q1
Q1
8
SOIC
D
8
SSOP
SSOP
SOIC
DBQ
DBQ
D
16
16
14
2500
2500
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
24-Jul-2013
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
OPA2353EA/250
OPA2353EA/2K5
OPA2353UA/2K5
OPA353UA/2K5
OPA4353EA/250
OPA4353EA/2K5
OPA4353UA/2K5
VSSOP
VSSOP
SOIC
DGK
DGK
D
8
8
250
2500
2500
2500
250
210.0
367.0
367.0
367.0
210.0
367.0
367.0
185.0
367.0
367.0
367.0
185.0
367.0
367.0
35.0
35.0
35.0
35.0
35.0
35.0
38.0
8
SOIC
D
8
SSOP
SSOP
SOIC
DBQ
DBQ
D
16
16
14
2500
2500
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明