AWT6301 [ANADIGICS]
CELLULAR DUAL MODE AMPLS/CDMA 3.4V/28 dBm LINEAR POWER AMPLIFIER MODULE; 蜂窝双模AMPLS / CDMA 3.4V / 28 dBm的线性功率放大器模块
| 型号： | AWT6301 |
| 厂家： | 
ANADIGICS, INC |
| 描述： | CELLULAR DUAL MODE AMPLS/CDMA 3.4V/28 dBm LINEAR POWER AMPLIFIER MODULE |
| 文件： | 总10页 (文件大小：243K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
AWT6301
Cellular Dual ModeAMPS/CDMA
3.4 V/28 dBm Linear PowerAmplifier Module
ADVANCED PRODUCT INFORMATION - Rev 0.1
FEATURES
InGaP HBT Technology
High Efficiency: 53 % AMPS, 39 % CDMA
Low Quiescent Current: 50 mA
Low Leakage Current in Shutdown Mode: <1 mA
VREF = +2.85 V (+2.7 V Min Over Temp.)
Optimized for a 50 W System
Low Profile Surface Mount Package: 1.1mm
CDMA 1XRTT, 1xEV-DO Compliant
Pinout Enables Easy Phone Board Migration
From 4mm x 4mm Package
APPLICATIONS
Single Mode CDMA Wireless Handsets
M9 Package
Dual Mode AMPS/CDMA Wireless Handsets
8 Pin 3mm x 3mm
Surface Mount Module
PRODUCT DESCRIPTION
The AWT6301 meets the increasing demands for
higher efficiency and linearity in AMPS/CDMA 1X
handsets, while reducing pcb area by 44%. The
package pinout was chosen to enable handset
manufacturers to switch from a 4mm x 4mm PA
module with very few layout changes to the phone
board. The device is manufactured on an advanced
InGaP HBT MMIC technology offering state-of-the-
art reliability, temperature stability, and ruggedness.
Selectable bias modes that optimize efficiency for
different output power levels, and a shutdown mode
with low leakage current, serve to increase handset
talk and standby time. The self contained 3mm x
3mm surface mount package incorporates matching
networks optimized for output power, efficiency and
linearity in a 50 W system.
GND at slug (pad)
8
1
2
3
4
V
REF
GND
Bias Control
RFOUT
VMODE
7
6
5
RFIN
GND
V
CC1
VCC2
Figure 1: Block Diagram
10/2003
AWT6301
GND
REF
8 GND
7 RFOUT
6 GND
V
1
2
3
4
V
MODE
RFIN
5
V
CC1
V
CC2
GND
Figure 2: Pinout (X-ray Top View)
Table 1: Pin Description
PIN
NAME
DESCRIPTION
Reference Voltage
Mode Control
RF Input
1
2
3
4
5
6
7
8
V
REF
V
MODE
RFIN
V
CC1
Supply Voltage
Supply Voltage
Ground
V
CC2
GND
RFOUT
GND
RF Output
Ground
ADVANCED PRODUCT INFORMATION - Rev 0.1
2
10/2003
AWT6301
ELECTRICAL CHARACTERISTICS
Table 2: Absolute Minimum and Maximum Ratings
PARAMETER
MIN
MAX
UNIT
Supply Voltage (VCC
With RF Drive
DC Only
)
0
0
+5
+8
V
Mode Control Voltage (VMODE
Reference Voltage (VREF
RF Input Power (PIN
Storage Temperature (TSTG
)
0
0
+3.5
+3.5
+10
V
V
)
)
-
dBm
°C
)
-40
+150
Stresses in excess of the absolute ratings may cause permanent
damage. Functional operation is not implied under these conditions.
Exposure to absolute ratings for extended periods of time may
adversely affect reliability.
Table 3: Operating Ranges
PARAMETER
MIN
824
+3.2
TYP
-
MAX
849
UNIT
MHz
V
COMMENTS
Operating Frequency (f)
Supply Voltage (VCC
)
+3.4
+4.2
+2.7
0
+2.85
-
+3.1
+0.5
PA "on"
PA "shut down"
Reference Voltage (VREF
)
V
V
+2.5
0
+2.8
-
+3.1
+0.5
Low Bias Mode
High Bias Mode
Mode Control Voltage (VMODE
)
30.5(1)
27.5(1)
31.0
28.0
-
-
AMPS
CDMA
RF Output Power (POUT
)
dBm
°C
Case Temperature (T
C
)
-20
-
+85
The device may be operated safely over these conditions; however, parametric performance is guaranteed
only over the conditions defined in the electrical specifications.
Notes:
(1) For operation at TC = +85 °C and VCC = +3.2 V, POUT is derated by 0.5 dB.
ADVANCED PRODUCT INFORMATION - Rev 0.1
3
10/2003
AWT6301
Table 4: Electrical Specifications - AMPS Operation
(T
C
= +25 °C, VCC = +3.4 V, VREF = +2.85 V, VMODE = 0 V, POUT = +31 dBm, 50 W system)
PARAMETER
MIN
TYP
MAX
UNIT
COMMENTS
25
23.5
27
27
30
31
Gain
dB
Over Temperature
Over Temperature
Gain Variation
-
50
-
0.3
53
1.0
-
dB
%
Power-Added Efficiency
Quiescent Current (Icq)
Reference Current
100
5.0
120
8
mA
mA
mA
VMODE = 0 V, High Bias
-
through VREF pin
through VMODE pin
Mode Control Current
-
0.35
1.0
V
V
CC = +4.2 V, VREF = 0 V,
MODE = 0 V
mA
Leakage Current
-
-
<1
5
Noise in Receive Band
-134
-132
dBm/Hz 869 MHz to 894 MHz
Harmonics
2fo
-
-
-35
-50
-30
-30
dBc
3fo, 4fo
Input Impedance
-
-
-
-
2:1
-65
VSWR
P
OUT < +31 dBm
Spurious Output Level
(all spurious outputs)
Load VSWR < 8:1
Applies over all voltage and
temperature operating ranges
dBc
V
P
CC = +5.0 V
IN = +5 dBm
Load mismatch stress with no
permanent degradation or failure
8:1
-
-
VSWR
Applies over full operating
temperature ranges
ADVANCED PRODUCT INFORMATION - Rev 0.1
4
10/2003
AWT6301
Table 5: Electrical Specifications - CDMA Operation
(T = +25 °C, VCC = +3.4 V, VREF = +2.85 V, 50 W system)
C
PARAMETER
MIN
TYP MAX
UNIT
COMMENTS
26
24.5
24
28
28
26
26
30
31
28
29
P
OUT = +28 dBm, VMODE = 0 V
Over Temperature
OUT = +16 dBm, VMODE = +2.85 V
Over Temperature
Gain
dB
P
23
Adjacent Channel Power
at 6885 kHz offset (1)
Primary Channel BW = 1.23 MHZ
-
-
-
-
-50
-
-50
-
-47
-44
-46
-44
P
OUT = +28 dBm, VMODE = 0 V
Over Temperature
OUT = +16 dBm, VMODE = +2.85 V
Over Temperature
dBc
Adjacent Channel BW = 30 kHz
P
Adjacent Channel Power
at 61.98 MHz offset (1)
Primary Channel BW = 1.23 MHZ
Adjacent Channel BW = 30 kHz
-
-
-60
-68
-57
-57
P
P
OUT = +28 dBm, VMODE = 0 V
OUT = +16 dBm, VMODE = +2.85 V
dBc
%
Over Temperature
37
8
39
8.5
-
-
P
P
OUT = +28 dBm, VMODE = 0 V
OUT = +16 dBm, VMODE = +2.85 V
Power-Added Efficiency (1)
Quiescent Current (Icq)
Reference Current
-
-
-
50
5
60
8
mA
mA
mA
V
MODE = 0 V, Low Bias
through VREF pin
through VMODE pin
Mode Control Current
0.35
1.0
V
V
CC = +4.2 V, VREF = 0 V,
MODE = 0 V
mA
Leakage Current
-
-
<1
5
Noise in Receive Band
-135
-133 dBm/Hz 869 MHz to 894 MHz
Harmonics
2fo
-
-
-35
-50
-30
dBc
-30
3fo, 4fo
Input Impedance
-
-
-
-
2:1
-65
VSWR
dBc
P
OUT < +28 dBm
Spurious Output Level
(all spurious outputs)
Load VSWR < 8:1
Applies over all voltage and
temperature operating ranges
V
P
CC = +5.0 V
IN = +5 dBm
Load mismatch stress with no
permanent degradation or failure
8:1
-
-
VSWR
Applies over full operating
temperature ranges
Notes:
(1) PAE and ACP limit applies at 836.5 MHz.
ADVANCED PRODUCT INFORMATION - Rev 0.1
5
10/2003
AWT6301
APPLICATION INFORMATION
Bias Modes
To ensure proper performance, refer to all related
Application Notes on the ANADIGICS web site:
http://www.anadigics.com
The power amplifier may be placed in either a Low
Bias mode or a High Bias mode by applying the
appropriate logic level (see Operating Ranges table)
to the VMODE voltage. The Bias Control table lists the
recommended modes of operation for various
applications.
Shutdown Mode
The power amplifier may be placed in a shutdown
mode by applying a logic low levels (see Operating
Ranges table) to both the VREF and VMODE voltages.
Table 6: Bias Control
P
OUT
BIAS
APPLICATION
AMPS
LEVELS
MODE
V
REF
V
MODE
(all)
High
Low
+2.85 V
0 V
CDMA - low power
CDMA - high power
Shutdown
<+16 dBm
>+16 dBm
-
+2.85 V +2.85 V
High
+2.85 V
0 V
0 V
0 V
Shutdown
ADVANCED PRODUCT INFORMATION - Rev 0.1
6
10/2003
AWT6301
PACKAGE OUTLINE
Figure 3: M9 Package Outline - 8 Pin 3mm x 3mm Surface Mount Module
Figure 4: Branding Specification
ADVANCED PRODUCT INFORMATION - Rev 0.1
7
10/2003
AWT6301
COMPONENT PACKAGING
Figure 5: Tape & Reel Packaging
Table 7: Tape & Reel Dimensions
PACKAGE TYPE TAPE WIDTH
3mm X 3mm 12mm
POCKET PITCH REEL CAPACITY MAX REEL DIA
4mm 2500 13"
ADVANCED PRODUCT INFORMATION - Rev 0.1
8
10/2003
AWT6301
NOTES
ADVANCED PRODUCT INFORMATION - Rev 0.1
9
10/2003
AWT6301
ORDERING INFORMATION
TEMPERATURE
PACKAGE
DESCRIPTION
ORDER NUMBER
COMPONENT PACKAGING
RANGE
8 Pin 3mm x 3mm
Surface Mount
Module
AWT6301M9P8
-30 °C to +110 °C
Tape and Reel, 2500 pieces per Reel
ANADIGICS, Inc.
141 Mount Bethel Road
Warren, New Jersey 07059, U.S.A.
Tel: +1 (908) 668-5000
Fax: +1 (908) 668-5132
URL: http://www.anadigics.com
E-mail: Mktg@anadigics.com
IMPORTANT NOTICE
ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without
notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are
subject to change prior to a products formal introduction. Information in Data Sheets have been carefully checked and are
assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges
customers to verify that the information they are using is current before placing orders.
WARNING
ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS
product in any such application without written consent is prohibited.
ADVANCED PRODUCT INFORMATION - Rev 0.1
10
10/2003
相关型号：
©2020 ICPDF网 联系我们和版权申明