AWT6302 [ANADIGICS]
PCS/CDMA 3.4V/28dBm Linear Power Amplifier Module; PCS / CDMA 3.4V / 28dBm的线性功率放大器模块
| 型号： | AWT6302 |
| 厂家： | 
ANADIGICS, INC |
| 描述： | PCS/CDMA 3.4V/28dBm Linear Power Amplifier Module |
| 文件： | 总8页 (文件大小：178K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
AWT6302
PCS/CDMA 3.4V/28dBm
Linear Power Amplifier Module
ADVANCED PRODUCT INFORMATION - Rev 0.1
FEATURES
•
•
•
•
•
•
•
InGaP HBT Technology
High Efficiency: 40%
Low Quiescent Current: 50 mA
Low Leakage Current in Shutdown Mode: <1 µA
VREF = +2.8 V (+2.7 V min over temp)
Optimized for a 50 Ω System
Low Profile Miniature Surface Mount Package:
1.1mm
•
•
CDMA 1XRTT, 1xEV-DO Compliant
Pinout Enables Easy Phone Board Migration
From 4mm x 4mm Package
M9 Package
8 Pin 3mm x 3mm
Surface Mount Module
APPLICATIONS
•
PCS CDMA Wireless Handsets
•
Dual Band CDMA Wireless Handsets
PRODUCT DESCRIPTION
The AWT6302 meets the increasing demands for
higher efficiency and linearity in CDMA 1X handsets,
while reducing pcb area by 44%. The package
pinout was chosen to enable handset
manufacturers to switch from a 4mm x 4mm PA
module with very few layout changes to the phone
board. The PA module is optimized for VREF = +2.8 V, a
requirement for compatibility with the Qualcomm®
6000 chipset. The device is manufactured on an
advanced InGaP HBT MMIC technology offering
state-of-the-art reliability, temperature stability, and
ruggedness. Selectable bias modes that optimize
efficiency for different output power levels, and a
shutdown mode with low leakage current, increase
handset talk and standby time. The self-contained
3mm x 3mm surface mount package incorporates
matching networks optimized for output power,
efficiency, and linearity in a 50 Ω system.
GND at slug (pad)
1
8
7
V
CC
V
CC
2
3
4
RFIN
RFOUT
GND
GND
V
MODE
6
5
Bias Control
V
REF
Figure 1: Block Diagram
04/2003
AWT6302
GND
V
CC
V
CC
8
7
6
5
1
2
3
4
RFIN
RFOUT
GND
GND
V
MODE
VREF
GND
Figure 2: Pinout (X-ray Top View)
Table 1: Pin Description
PIN
1
NAME
DESCRIPTION
Supply Voltage
RF Input
V
CC
2
RFIN
3
V
MODE
Mode Control Voltage
Reference Voltage
Ground
4
V
REF
GND
GND
RFOUT
5
6
Ground
7
RF Output
8
V
CC
Supply Voltage
ADVANCED PRODUCT INFORMATION - Rev 0.1
2
04/2003
AWT6302
ELECTRICAL CHARACTERISTICS
Table 2: Absolute Minimum and Maximum Ratings
PARAMETER
MIN
0
MAX
+5
UNIT
V
Supply Voltage (VCC
)
Mode Control Voltage (VMODE
Reference Voltage (VREF
RF Input Power (PIN
Storage Temperature (TSTG
)
0
+3.5
+3.5
+10
+150
V
)
0
V
)
-
dBm
°C
)
-40
Stresses in excess of the absolute ratings may cause permanent
damage. Functional operation is not implied under these conditions.
Exposure to absolute ratings for extended periods of time may
adversely affect reliability.
Table 3: Operating Ranges
PARAMETER
MIN
1850
+3.2
TYP
-
MAX
1910
+4.2
UNIT
MHz
V
COMMENTS
Operating Frequency (f)
Supply Voltage (VCC
Reference Voltage (VREF
Mode Control Voltage (VMODE
)
+3.4
+2.7
0
+2.8
-
+3.1
+0.5
PA "on"
)
V
V
PA "shut down"
+2.3
0
+2.8
-
+3.1
+0.5
Low Bias Mode
High Bias Mode
)
RF Output Power (POUT
)
-
+28.0
-
-
dBm
°C
Case Temperature (T
C
)
-30
+85
The device may be operated safely over these conditions; however, parametric performance is guaranteed
only over the conditions defined in the electrical specifications.
ADVANCED PRODUCT INFORMATION - Rev 0.1
3
04/2003
AWT6302
Table 4: Electrical Specifications
(T
C
= +25 °C, VCC = +3.4 V, VREF = +2.8 V, 50 Ω system)
MIN
TYP
MAX
UNIT
PARAMETER
COMMENTS
Gain
-
-
27
25
-
-
P
P
OUT = +28 dBm, VMODE = 0 V
OUT = +16 dBm, VMODE = +2.8 V
dB
Adjacent Channel Power
at ±1.25 kHz offset
-
-
-49
-52
-
-
P
P
OUT = +28 dBm, VMODE = 0 V
OUT = +16 dBm, VMODE = +2.8 V
dB
Primary Channel BW = 1.23 MHz
Adjacent Channel BW = 30 kHz
Adjacent Channel Power
at ±2.25 MHz offset
-
-
-60
-70
-
-
P
P
OUT = +28 dBm, VMODE = 0 V
OUT = +16 dBm, VMODE = +2.8 V
dB
%
Primary Channel BW = 1.23 MHz
Adjacent Channel BW = 30 kHz
-
-
40
9
-
-
P
P
OUT = +28 dBm, VMODE = 0 V
OUT = +16 dBm, VMODE = +2.8 V
Power-Added Efficiency
Quiescent Current (Icq)
Reference Current
-
-
-
48
3.5
0.3
-
5
-
mA
mA
mA
V
MODE = +2.8 V
through VREF pin, PA "on"
Mode Control Current
through VMODE pin, VMODE = +2.8 V
V
V
CC = +4.2 V, VREF = 0 V
MODE = 0 V
Leakage Current
-
-
<1
5
-
µA
Noise in Receive Band
-137
dBm/Hz 1930 MHz to 1990 MHz
Harmonics
2fo
-
-
-40
-55
-
-
dBc
3fo, 4fo
Input Impedance
-
-
2:1
VSWR
P
OUT < +28 dBm
In-band load VSWR < 8:1
Spurious Output Level
(all spurious outputs)
-
-
-65
dBc
Out-of-band load VSWR < 8:1
Applies over all voltage and
temperature operating ranges
V
CC = +5.0 V, PIN = +5 dBm
Load mismatch stress with no
permanent degradation or failure
8:1
-
-
VSWR Applies over full operating
temperature range
ADVANCED PRODUCT INFORMATION - Rev 0.1
4
04/2003
AWT6302
APPLICATION INFORMATION
Bias Modes
To ensure proper performance, refer to all related
Application Notes on the ANADIGICS web site:
http://www.anadigics.com
The power amplifier may be placed in either a Low
Bias mode or a High Bias mode by applying the
appropriate logic level (see Operating Ranges table)
to the VMODE voltage. The Bias Control table lists the
recommended modes of operation for various
applications.
Shutdown Mode
The power amplifier may be placed in a shutdown
mode by applying logic low levels (see Operating
Ranges table) to both the VREF and VMODE voltages.
Table 5: Bias Control
P
OUT
BIAS
APPLICATION
CDMA - low power
CDMA - high power
Shutdown
LEVELS
<+16dBm
>+16 dBm
-
MODE
V
REF
V
MODE
Low
High
+2.8 V +2.8 V
+2.8 V
0 V
0 V
0 V
Shutdown
ADVANCED PRODUCT INFORMATION - Rev 0.1
5
04/2003
AWT6302
PACKAGE OUTLINE
Figure 3: M9 Package Outline - 8 Pin 3mm x 3mm Surface Mount Module
ADVANCED PRODUCT INFORMATION - Rev 0.1
6
04/2003
AWT6302
NOTES
ADVANCED PRODUCT INFORMATION - Rev 0.1
7
04/2003
AWT6302
ANADIGICS, Inc.
141 Mount Bethel Road
Warren, New Jersey 07059, U.S.A.
Tel: +1 (908) 668-5000
Fax: +1 (908) 668-5132
URL: http://www.anadigics.com
E-mail: Mktg@anadigics.com
IMPORTANT NOTICE
ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without
notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are
subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are
assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges
customers to verify that the information they are using is current before placing orders.
WARNING
ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS
product in any such application without written consent is prohibited.
ADVANCED PRODUCT INFORMATION - Rev 0.1
8
04/2003
相关型号：
©2020 ICPDF网 联系我们和版权申明