AWT6301RM9Q7 [ANADIGICS]
Cellular CDMA 3.4 V/28 dBm Linear Power Amplifier Module; 蜂窝CDMA 3.4 V / 28 dBm的线性功率放大器模块
| 型号： | AWT6301RM9Q7 |
| 厂家： | 
ANADIGICS, INC |
| 描述： | Cellular CDMA 3.4 V/28 dBm Linear Power Amplifier Module |
| 文件： | 总9页 (文件大小：364K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
AWT6301R
Cellular CDMA 3.4 V/28 dBm
Linear Power Amplifier Module
Data Sheet - Rev 2.0
FEATURES
•
InGaP HBT Technology
•
High Efficiency:
40%, VMODE = 0 V
41%, VMODE = +2.85 V (no mode switching)
Low Quiescent Current: 50 mA
Low Leakage Current in Shutdown Mode: <1 µA
•
•
•
•
•
•
•
V
REF = +2.85 V (+2.75 V Min Over Temp.)
Optimized for a 50 Ω System
Low Profile Surface Mount Package: 1.1mm
CDMA 1XRTT, 1xEV-DO Compliant
Pinout Enables Easy Phone Board Migration
From 4 mm x 4 mm Package
•
RoHS Compliant Package, 250 oC MSL-3
M9 Package
8 Pin 3 x 3 x 1 mm
Surface Mount Module
APPLICATIONS
•
CDMA/EVDO Cell-band Wireless Handsets and
Data Devices
PRODUCT DESCRIPTION
The AWT6301R meets the increasing demands for
higher efficiency and linearity in CDMA1X handsets.
The package pinout was chosen to enable handset
manufacturers to switch from a 4mm x 4mm PA
module with very few layout changes to the phone
board. The device is manufactured on an advanced
InGaP HBT MMIC technology offering state-of-the-
art reliability, temperature stability, and ruggedness.
Selectable bias modes that optimize efficiency
for different output power levels, and a shutdown
mode with low leakage current, serve to increase
handset talk and standby time. The self contained
3 mm x 3 mm x 1 mm surface mount package
incorporates matching networks optimized for output
power, efficiency and linearity in a 50 Ω system.
GND at slug (pad)
8
1
VREF
GND
Bias Control
RFOUT
VMODE
2
3
4
7
6
5
RFIN
GND
VCC1
VCC2
Figure 1: Block Diagram
10/2008
AWT6301R
GND
REF
V
1
2
3
4
8 GND
7 RFOUT
6 GND
5 VCC2
V
MODE
RFIN
V
CC1
GND
Figure 2: Pinout (X-ray Top View)
Table 1: Pin Description
PIN
NAME
DESCRIPTION
Reference Voltage
Mode Control
RF Input
1
2
3
4
5
6
7
8
V
REF
V
MODE
RFIN
V
CC1
Supply Voltage
Supply Voltage
Ground
V
CC2
GND
RFOUT
GND
RF Output
Ground
Data Sheet - Rev 2.0
10/2008
2
AWT6301R
ELECTRICAL CHARACTERISTICS
Table 2: Absolute Minimum and Maximum Ratings
PARAMETER
MIN
MAX
UNIT
Supply Voltage (VCC
With RF Drive
DC Only
)
0
0
+5
+8
V
Mode Control Voltage (VMODE
Reference Voltage (VREF
RF Input Power (PIN
Storage Temperature (TSTG
)
0
0
+3.5
+3.5
+10
V
V
)
)
-
dBm
°C
)
-40
+150
Stresses in excess of the absolute ratings may cause permanent damage.
Functional operation is not implied under these conditions. Exposure
to absolute ratings for extended periods of time may adversely affect
reliability.
Table 3: Operating Ranges
PARAMETER
MIN
824
+3.2
TYP
-
MAX
849
UNIT
MHz
V
COMMENTS
Operating Frequency (f)
Supply Voltage (VCC
)
+3.4
+4.2
+2.75 +2.85
+3.1
+0.5
PA "on"
PA "shut down"
Reference Voltage (VREF
)
V
V
0
-
+2.5
0
+2.85
-
+3.1
+0.5
Low Bias Mode
High Bias Mode
Mode Control Voltage (VMODE
RF Output Power (POUT
Case Temperature (T
)
)
27.5(1)
28.0
-
dBm
°C
CDMA
C
)
-30
-
+85
The device may be operated safely over these conditions; however, parametric performance is guaranteed only
over the conditions defined in the electrical specifications.
Notes:
(1) For operation at VCC = +3.2 V, POUT is derated by 0.5 dB.
Data Sheet - Rev 2.0
10/2008
3
AWT6301R
Table 4: Electrical Specifications - CDMA Operation with mode switching
(T = +25 °C, VCC = +3.4 V, VREF = +2.85 V, 50 Ω system)
C
PARAMETER
MIN
TYP MAX
UNIT
COMMENTS
25
24
27.5
26.5
30
28
P
P
OUT = +28 dBm, VMODE = 0 V
OUT = +16 dBm, VMODE = +2.85 V
Gain
dB
Adjacent Channel Power
at 885 kHz offset (1)
Primary Channel BW = 1.23 MHZ
Adjacent Channel BW = 30 kHz
-
-
-50
-51
-47
-47
P
P
OUT = +28 dBm, VMODE = 0 V
OUT = +16 dBm, VMODE = +2.85 V
dBc
Adjacent Channel Power
at 1.98 MHz offset (1)
Primary Channel BW = 1.23 MHZ
Adjacent Channel BW = 30 kHz
-
-
-63
-65
-57
-57
P
P
OUT = +28 dBm, VMODE = 0 V
OUT = +16 dBm, VMODE = +2.85 V
dBc
37
8
40
9
-
-
P
P
OUT = +28 dBm, VMODE = 0 V
OUT = +16 dBm, VMODE = +2.85 V
Power-Added Efficiency (1)
%
Quiescent Current (Icq)
Reference Current
-
-
-
50
1.5
0.3
70
3
mA
mA
mA
V
MODE = +2.85 V, Low Bias
through VREF pin
through VMODE pin
Mode Control Current
1.0
V
V
CC = +4.2 V, VREF = 0 V,
MODE = 0 V
A
Leakage Current
-
-
<1
5
Noise in Receive Band
-133
-131 dBm/Hz 869 MHz to 894 MHz
Harmonics
2fo
-
-
-35
-50
-30
dBc
-30
3fo, 4fo
Input Impedance
-
-
2:1
VSWR
P
OUT < +28 dBm
In-band Load VSWR < 5:1
Out-of-band Load VSWR < 10:1
Applies over all operating
conditions
Spurious Output Level
(all spurious outputs)
-
-
-65
dBc
Load mismatch stress with no
permanent degradation or failure
Applies over all operating
conditions
10:1
-
-
VSWR
Notes:
(1) PAE and ACP limit applies at 836.5 MHz.
Data Sheet - Rev 2.0
10/2008
4
AWT6301R
Table 5: Electrical Specifications - CDMA Operation in Low Power Mode
(T = +25 °C, VCC = +3.4 V, VREF = +2.85 V, VMODE = +2.85 V, 50 Ω system)
C
PARAMETER
MIN
TYP MAX
UNIT
COMMENTS
24
24
27.0
26.5
29
28
P
P
OUT = +28 dBm
OUT = +16 dBm
Gain
dB
Adjacent Channel Power
at 885 kHz offset (1)
Primary Channel BW = 1.23 MHZ
Adjacent Channel BW = 30 kHz
-
-
-50
-51
-47
-47
P
P
OUT = +28 dBm
OUT = +16 dBm
dBc
Adjacent Channel Power
at 1.98 MHz offset (1)
Primary Channel BW = 1.23 MHZ
Adjacent Channel BW = 30 kHz
-
-
-61
-65
-57
-57
P
P
OUT = +28 dBm
OUT = +16 dBm
dBc
37
8
41
9
-
-
P
P
OUT = +28 dBm
OUT = +16 dBm
Power-Added Efficiency (1)
%
Quiescent Current (Icq)
Reference Current
-
-
-
50
1.5
0.3
70
3
mA
mA
mA
V
MODE = +2.85 V, Low Bias
through VREF pin
through VMODE pin
Mode Control Current
1.0
V
V
CC = +4.2 V, VREF = 0 V,
MODE = 0 V
A
Leakage Current
-
-
<1
5
Noise in Receive Band
-133
-131 dBm/Hz 869 MHz to 894 MHz
Harmonics
2fo
-
-
-35
-50
-30
dBc
-30
3fo, 4fo
Input Impedance
-
-
2:1
VSWR
P
OUT < +28 dBm
In-band Load VSWR < 5:1
Out-of-band Load VSWR < 10:1
Applies over all operating
conditions
Spurious Output Level
(all spurious outputs)
-
-
-65
dBc
Load mismatch stress with no
permanent degradation or failure
Applies over all operating
conditions
10:1
-
-
VSWR
Notes:
(1) PAE and ACP limit applies at 836.5 MHz.
Data Sheet - Rev 2.0
10/2008
5
AWT6301R
APPLICATION INFORMATION
Bias Modes
To ensure proper performance, refer to all related
Application Notes on the ANADIGICS web site:
http://www.anadigics.com
The power amplifier may be placed in either a Low Bias
mode or a High Bias mode by applying the appropriate
logic level (see Operating Ranges table) to the VMODE
voltage. The Bias Control table lists the recommended
modes of operation for various applications.
Shutdown Mode
The power amplifier may be placed in a shutdown
mode by applying a logic low levels (see Operating
Ranges table) to both the VREF and VMODE voltages.
Table 8: Bias Control
P
OUT
BIAS
APPLICATION
AMPS
LEVELS
MODE
V
REF
V
MODE
(all)
High
Low
+2.85 V
0 V
CDMA - low power
CDMA - high power
Shutdown
<+28 dBm
>+16 dBm
-
+2.85 V +2.85 V
High
+2.85 V
0 V
0 V
0 V
Shutdown
VREF
C6
1 µF
1
2
8
VREF
GND
C5
68 pF
7
VMODE
VMODE
RFOUT
RFOUT
3
4
6
RFIN
RFIN
GND
5
VCC1
VCC1
VCC2
VCC2
C2
10 µF
C1
10 µF
C4
68 pF
GND
at slug
Figure 3: Application Circuit
Data Sheet - Rev 2.0
10/2008
6
AWT6301R
PACKAGE OUTLINE
Figure 4: M9 Package Outline - 8 Pin 3 mm x 3 mm x 1 mm Surface Mount Module
6301R
LLLLLNN
BBBBCC
Figure 5: Branding Specification
Data Sheet - Rev 2.0
10/2008
7
AWT6301R
COMPONENT PACKAGING
Figure 6: Tape & Reel Packaging
Table 9: Tape & Reel Dimensions
PACKAGE TYPE
TAPE WIDTH
12 mm
POCKET PITCH REEL CAPACITY MAX REEL DIA
3 mm x 3 mm x 1 mm
4 mm
2500
7"
Data Sheet - Rev 2.0
10/2008
8
AWT6301R
ORDERING INFORMATION
TEMPERATURE
PACKAGE
DESCRIPTION
ORDER NUMBER
COMPONENT PACKAGING
RANGE
8 Pin
3 mm x 3 mm x 1 mm
Surface Mount
Module
AWT6301RM9Q7
-30 °C to +85 °C
Tape and Reel, 2500 pieces per Reel
ANADIGICS, Inc.
141 Mount Bethel Road
Warren, New Jersey 07059, U.S.A.
Tel: +1 (908) 668-5000
Fax: +1 (908) 668-5132
URL: http://www.anadigics.com
E-mail: Mktg@anadigics.com
IMPORTANT NOTICE
ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice.
The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to
change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed
to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers
to verify that the information they are using is current before placing orders.
WARNING
ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of anANADIGICS product
in any such application without written consent is prohibited.
Data Sheet - Rev 2.0
10/2008
9
相关型号：
©2020 ICPDF网 联系我们和版权申明