DAC8420EPZ [ADI]
Quad 12-Bit Serial Voltage Output DAC;型号: | DAC8420EPZ |
厂家: | ADI |
描述: | Quad 12-Bit Serial Voltage Output DAC 信息通信管理 光电二极管 转换器 |
文件: | 总23页 (文件大小:511K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Quad 12-Bit Serial Voltage Output DAC
Data Sheet
DAC8420
FEATURES
FUNCTIONAL BLOCK DIAGRAM
VREFHI
5
VDD
1
Guaranteed monotonic over temperature
Excellent matching between DACs
Unipolar or bipolar operation
Buffered voltage outputs
High speed serial digital interface
Reset-to-zero scale or midscale
Wide supply range, +5 V only to 15 V
Low power consumption (35 mW maximum)
Available in 16-Lead PDIP, SOIC, and CERDIP packages
DAC8420
10
SDI
REG
A
DAC A
7
6
3
2
VOUTA
VOUTB
VOUTC
VOUTD
12
12
11
CS
REG
B
CLK
DAC B
DAC C
DAC D
SHIFT
REGISTER
13
14
NC
LD
REG
C
APPLICATIONS
4
Software controlled calibration
Servo controls
Process control and automation
ATE
DECODE
REG
D
2
9
16
CLSEL CLR
8
15
4
GND
VREFLO
VSS
Figure 1.
GENERAL DESCRIPTION
The DAC8420 is a quad, 12-bit voltage-output DAC with serial
digital interface in a 16-lead package. Utilizing BiCMOS tech-
nology, this monolithic device features unusually high circuit
density and low power consumption. The simple, easy-to-use
serial digital input and fully buffered analog voltage outputs
require no external components to achieve a specified per-
formance.
CLR
forces all four DAC
The user-programmable reset control
outputs to either zero scale or midscale, asynchronously overriding
the current DAC register values. The output voltage range,
determined by the inputs VREFHI and VREFLO, is set by the
user for positive or negative unipolar or bipolar signal swings
within the supplies, allowing considerable design flexibility.
The DAC8420 is available in 16-lead PDIP, SOIC, and CERDIP
packages. Operation is specified with supplies ranging from +5 V
only to 15 V, with references of +2.5 V to 10 V, respectively.
Power dissipation when operating from 15 V supplies is less than
255 mW (maximum) and only 35 mW (maximum) with a +5 V
supply.
The 3-wire serial digital input is easily interfaced to micro-
processors running at 10 MHz with minimal additional
circuitry. Each DAC is addressed individually by a 16-bit serial
word consisting of a 12-bit data word and an address header.
Rev. C
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2003–2016 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
DAC8420
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
CS
and CLK........................................... 13
Correct Operation of
CLR
Applications....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description......................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Electrical Characteristics............................................................. 3
Absolute Maximum Ratings............................................................ 6
Thermal Resistance ...................................................................... 6
ESD Caution.................................................................................. 6
Pin Configurations and Function Descriptions ........................... 8
Typical Performance Characteristics ............................................. 9
Theory of Operation ...................................................................... 13
Introduction ................................................................................ 13
Digital Interface Operation....................................................... 13
Using
and CLSEL............................................................... 13
Programming the Analog Outputs .......................................... 13
VREFHI Input Requirements................................................... 15
Power-Up Sequence ................................................................... 15
Applications..................................................................................... 16
Power Supply Bypassing and Grounding................................ 16
Analog Outputs .......................................................................... 16
Reference Configuration ........................................................... 17
Isolated Digital Interface ........................................................... 18
Dual Window Comparator ....................................................... 19
MC68HC11 Microcontroller Interfacing................................ 19
DAC8420 to M68HC11 Interface Assembly Program.......... 20
Outline Dimensions....................................................................... 21
Ordering Guide .......................................................................... 22
REVISION HISTORY
9/2016—Rev. B to Rev. C
Updated Outline Dimensions....................................................... 22
Changes to Ordering Guide .......................................................... 22
5/2007—Rev. A to Rev. B
Updated Format..................................................................Universal
Changes to Endnote 3 ...................................................................... 4
Changes to Table 3............................................................................ 6
Changes to Table 4............................................................................ 2
Updated Outline Dimensions....................................................... 22
Changes to Ordering Guide .......................................................... 23
9/2003—Rev. 0 to Rev. A
Changes to General Description .................................................... 1
Deleted Wafer Test Limits table...................................................... 4
Deleted Dice Characteristics........................................................... 4
Updated Ordering Guide................................................................. 4
Added Power-Up Sequence section ............................................. 12
Updated Outline Dimensions....................................................... 17
Rev. C | Page 2 of 23
Data Sheet
DAC8420
SPECIFICATIONS
ELECTRICAL CHARACTERISTICS1
At VDD = +5.0 V 5%, VSS = 0 V, V VREFHI = +2.5 V, VVREFLD = 0 V, and V SS = −5.0 V 5%, VVREFLO = −2.5 V, −40°C ≤ TA ≤ +85°C unless
otherwise noted.2
Table 1.
Parameter
Symbol Test Conditions/Comments
Min
Typ
Max
Unit
STATIC ACCURACY
Integral Linearity E Grade
Integral Linearity E Grade
Integral Linearity F Grade
Integral Linearity F Grade
Differential Linearity
Zero-Scale Error
Full-Scale Error
Zero-Scale Error
Full-Scale Error
Zero-Scale Temperature Coefficient
Full-Scale Temperature Coefficient
MATCHING PERFORMANCE
Linearity Matching
INL
INL
INL
INL
DNL
ZSE
FSE
ZSE
FSE
TCZSE
TCFSE
±±
±ꢀ
±ꢁ
±1
±1
±3
±2
±4
±1
±4
±4
±8
±8
LSB
LSB
LSB
LSB
LSB
LSB
LSB
LSB
VSS = 0 V3
VSS = 0 V3
Monotonic over temperature
RL = 2 kΩ, VSS = −5 V
RL = 2 kΩ, VSS = −5 V
RL = 2 kΩ, VSS = 0 V3
RL = 2 kΩ, VSS = 0 V3
RL = 2 kΩ, VSS = −5 V4
RL = 2 kΩ, VSS = −5 V4
±±
LSB
ppm/°C
ppm/°C
±10
±10
±1
LSB
REFERENCE
Positive Reference Input Range5
Negative Reference Input Range5
Negative Reference Input Range
Reference High Input Current
Reference Low Input Current
AMPLIFIER CHARACTERISTICS
Output Current
VVREFHI
VVREFLO
VVREFLO
IVREFHI
VVREFLO + 2.5
VSS
0
−0.75
−1.0
VDD − 2.5
VVREFHI − 2.5
VVREFHI − 2.5
V
V
V
mA
mA
VSS = 0 V5
Code 0x000, Code 0x555
Code 0x000, Code 0x555, VSS = −5 V
±0.25 +0.75
−0.6
IVREFLO
IOUT
tS
SR
VSS = −5 V
To 0.01%6
10% to 90%6
−1.25
2.4
+1.25
mA
μs
V/μs
Settling Time
Slew Rate
8
1.5
LOGIC CHARACTERISTICS
Logic Input High Voltage
Logic Input Low Voltage
Logic Input Current
Input Capacitance4
VINH
VINL
IIN
V
V
μA
pF
0.8
10
CIN
13
LOGIC TIMING CHARACTERISTICS4, 7
Data Setup Time
Data Hold
Clock Pulse Width High
Clock Pulse Width Low
Select Time
Deselect Delay
Load Disable Time
Load Delay
Load Pulse Width
tDS
tDH
tCH
tCL
tCSS
tCSH
tLD1
tLD2
tLDW
tCLRW
25
55
90
120
90
5
130
35
80
150
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Clear Pulse Width
Rev. C | Page 3 of 23
DAC8420
Data Sheet
Parameter
Symbol Test Conditions/Comments
Min
Typ
Max
Unit
SUPPLY CHARACTERISTICS
Power Supply Sensitivity
Positive Supply Current
Negative Supply Current
Power Dissipation
PSRR
IDD
ISS
0.002
4
−3
20
0.01
7
%/%
mA
mA
−6
PDISS
VSS = 0 V
35
mW
1 Typical values indicate performance measured at 25°C.
2 All supplies can be varied ±5% and operation is guaranteed. Device is tested with VDD = 4.75 V.
3 For single-supply operation (VVREFLO = 0 V, VSS = 0 V), due to internal offset errors INL and DNL are measured beginning at Code 0x005.
4 Guaranteed, but not tested.
5 Operation is guaranteed over this reference range, but linearity is neither tested nor guaranteed.
6 VOUT swing between +2.5 V and −2.5 V with VDD = 5.0 V.
7 All input control signals are specified with tr = tf = 5 ns (10% to 90% of 5 V) and timed from a voltage level of 1.6 V.
Rev. C | Page 4 of 23
Data Sheet
DAC8420
At VDD = +15.0 V 5%, VSS = −15.0 V 5%, VVREFHI = +10.0 V, VVREFLO = −10.0 V, −40°C ≤ TA ≤ +85°C unless otherwise noted.1, 2
Table 2.
Parameter
Symbol Test Conditions/Comments
Min
Typ
Max
Unit
STATIC ACCURACY
Integral Linearity E Grade
Integral Linearity F Grade
Differential Linearity
Zero-Scale Error
Full-Scale Error
Zero-Scale Temperature Coefficient
Full-Scale Temperature Coefficient TCFSE
MATCHING PERFORMANCE
Linearity Matching
INL
INL
DNL
ZSE
FSE
TCZSE
±±
±ꢀ
±±
±ꢀ
±1
±1
±2
±2
LSB
LSB
LSB
LSB
LSB
ppm/°C
ppm/°C
Monotonic over temperature
RL = 2 kΩ
RL = 2 kΩ
RL = 2 kΩ3
±4
±4
RL = 2 kΩ3
±1
LSB
REFERENCE
Positive Reference Input Range4
Negative Reference Input Range4
Reference High Input Current
Reference Low Input Current
AMPLIFIER CHARACTERISTICS
Output Current
VVREFHI
VVREFLO
IVREFHI
VVREFLO + 2.5
−10
−2.0
VDD − 2.5
VVREFHI − 2.5
+2.0
V
V
mA
mA
Code 0x000, Code 0x555
Code 0x000, Code 0x555
±1.0
−2.0
IVREFLO
−3.5
IOUT
tS
SR
−5
+5
mA
μs
V/μs
Settling Time
Slew Rate
To 0.01%5
10% to 90%5
13
2
DYNAMIC PERFORMANCE
Analog Crosstalk3
Digital Feedthrough3
Large Signal Bandwidth
Glitch Impulse
>64
>72
90
dB
dB
kHz
μV-s
3 dB, VVREFHI = 5 V + 10 V p-p, VVREFLO = −10 V3
Code Transition = 0x7FF to 0x8003
6
LOGIC CHARACTERISTICS
Logic Input High Voltage
Logic Input Low Voltage
Logic Input Current
Input Capacitance3
VINH
VINL
IIN
2.4
V
V
μA
pF
0.8
10
CIN
13
LOGIC TIMING CHARACTERISTICS3, 6
Data Setup Time
Data Hold
Clock Pulse Width High
Clock Pulse Width Low
Select Time
Deselect Delay
Load Disable Time
Load Delay
Load Pulse Width
tDS
tDH
tCH
tCL
tCSS
tCSH
tLD1
tLD2
tLDW
tCLRW
25
20
30
50
55
15
40
15
45
70
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Clear Pulse Width
SUPPLY CHARACTERISTICS
Power Supply Sensitivity
Positive Supply Current
Negative Supply Current
Power Dissipation
PSRR
IDD
ISS
0.002 0.01
%/%
mA
mA
6
9
−8
−5
PDISS
255
mW
1 Typical values indicate performance measured at 25°C.
2 All supplies can be varied ±5% and operation is guaranteed.
3 Guaranteed, but not tested.
4 Operation is guaranteed over this reference range, but linearity is neither tested nor guaranteed.
5 VOUT swing between +10 V and −10 V.
6 All input control signals are specified with tr = tf = 5 ns (10% to 90% of 5 V) and timed from a voltage level of 1.6 V.
Rev. C | Page 5 of 23
DAC8420
Data Sheet
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
THERMAL RESISTANCE
Table 3.
Table 4.
Parameter
Rating
Package Type
16-Lead PDIP (N)
16-Lead CERDIP (Q)
16-Lead SOIC (RW)
θJA
701
821
862
θJC
Unit
°C/W
°C/W
°C/W
VDD to GND
VSS to GND
VSS to VDD
VSS to VVREFLO
VVREFHI to VVREFLO
VVREFHI to VDD
IVREFHI, IVREFLO
−0.3 V, +18.0 V
+0.3 V, −18.0 V
−0.3 V, +36.0 V
−0.3 V, VSS − 2.0 V
+2.0 V, VDD − VSS
+2.0 V, +33.0 V
10 mA
27
9
22
1 θJA is specified for worst case mounting conditions, that is, θJA is specified for
device in socket.
2 θJA is specified for device on board.
ESD CAUTION
Digital Input Voltage to GND
Output Short-Circuit Duration
Operating Temperature Range
EP, FP, ES, FS, EQ, FQ
Dice Junction Temperature
Storage Temperature Range
Power Dissipation
Lead Temperature
Soldering
−0.3 V, VDD + 0.3 V
Indefinite
–40°C to +85°C
150°C
–65°C to +150°C
1000 mW
JEDEC Industry Standard
J-STD-020
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
Rev. C | Page 6 of 23
Data Sheet
DAC8420
DATA LOAD SEQUENCE
tCSH
CS
tCSS
SDI
A1
A0
X
X
D11
D10
D9
D8
D4
D3
D2
D1
D0
CLK
LD
tLD1
tLD2
tDS
tDH
DATA LOAD TIMING
CLEAR TIMING
CLSEL
SDI
tCLRW
CLR
CLK
CS
tCH
tCL
tS
tCSH
V
OUT
tLD2
tLDW
±1LSB
LD
tS
VOUTx
±1LSB
Figure 2. Timing Diagram
5kΩ
10kΩ
+15V
1N4001
1
16
+
10µF
0.1µF
NC
NC
15
14
2
3
4
5
6
7
8
10kΩ
–10V
1N4001
13 NC
DUT
10µF
0.1µF
0.1µF
+
+
12
11
10
9
5kΩ
NC
NC
10kΩ
+10V
1N4001
10µF
10kΩ
10kΩ
–15V
1N4001
NC = NO CONNECT
10µF
0.1µF
+
Figure 3. Burn-In Diagram
Rev. C | Page 7 of 23
DAC8420
Data Sheet
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
VDD
VOUTD
VOUTC
VREFLO
VREFHI
VOUTB
VOUTA
VSS
1
2
3
4
5
6
7
8
16 CLSEL
15 CLR
14 LD
VDD
VOUTD
VOUTC
VREFLO
VREFHI
VOUTB
VOUTA
VSS
1
2
3
4
5
6
7
8
16 CLSEL
15 CLR
14 LD
DAC8420
TOP VIEW
DAC8420
13 NC
13 NC
TOP VIEW
(Not to Scale)
12 CS
(Not to Scale)
12 CS
11 CLK
10 SDI
11 CLK
10 SDI
9
GND
9
GND
NC = NO CONNECT
NC = NO CONNECT
Figure 4. PDIP and CERDIP
Figure 5. SOIC
Table 5. Pin Function Descriptions
Pin No.
Mnemonic
Description
1
4
VDD
VREFLO
Positive Power Supply, 5 V to 15 V.
Reference Input. Lower DAC ladder reference voltage input, equal to zero-scale output. Allowable
range is VSS to (VVREFHI − 2.5 V).
5
VREFHI
Reference Input. Upper DAC ladder reference voltage input. Allowable range is (VDD − 2.5 V) to
(VVREFLO + 2.5 V).
7, 6, 3, 2
8
9
10
VOUTA through VOUTD
Buffered DAC Analog Voltage Outputs.
Negative Power Supply, 0 V to −15 V.
Power Supply, Digital Ground.
Serial Data Input. Data presented to this pin is loaded into the internal serial-parallel shift register,
which shifts data in, beginning with DAC Address Bit A1. This input is ignored when CS is high. SDI
is CMOS/TTL compatible. The format of the 16-bit serial word is shown in Table 8.
VSS
GND
SDI
11
12
CLK
CS
System Serial Data Clock Input, TTL/CMOS Levels. Data presented to the input SDI is shifted into
the internal serial-parallel input register on the rising edge of clock. This input is logically OR’ed
with CS.
Control Input, Device Chip Select, Active Low. This input is logically OR’ed with the clock and
disables the serial data register input when high. When low, data input clocking is enabled (see
Table 6). CS is CMOS/TTL compatible.
13
14
NC
LD
No Connect = Don’t Care.
Control Input, Asynchronous DAC Register Load Control, Active Low. The data currently contained
in the serial input shift register is shifted out to the DAC data registers on the falling edge of LD,
independent of CS. Input data must remain stable while LD is low. LD is CMOS/TTL compatible.
15
16
CLR
Control Input, Asynchronous Clear, Active Low. Sets internal data Register A through Register D to
zero or midscale, depending on current state of CLSEL. The data in the serial input shift register is
unaffected by this control. CLR is CMOS/TTL compatible.
CLSEL
Control Input, Determines action of CLR. If high, a clear command sets the internal DAC Register A
through Register D to midscale (0x800). If low, the registers are set to zero (0x000). CLSEL is CMOS/
TTL compatible.
Table 6. Control Function Logic Table
CLK1
CS1
LD
CLR
CLSEL
Serial Input Shift Register
DAC Register A to DAC Register D
NC2
NC2
NC2
↑
Low
High
High
NC2
High
High
High
Low
↑
NC (↑)2
NC2
High
High
High
High
High
↓
Low
Low
↑
High
High
High
High
High
High
Low
High /Low
NC2
NC2
NC2
NC2
NC2
No change
No change
No change
Shifts register one bit
Shifts register one bit
No change
Loads midscale value (0x800)
Loads zero-scale value (0x000)
Latches value
No change
No change
Loads the serial data-word3
Transparent4
Low
High
No change
No change
High
No change
1
CS
CLK and are interchangeable.
2 NC = Don’t Care.
3
CS
CS
Returning high while CLK is high avoids an additional false clock of serial input data. CLK and are interchangeable.
4
LD
Do not clock in serial data while
is low.
Rev. C | Page 8 of 23
Data Sheet
DAC8420
TYPICAL PERFORMANCE CHARACTERISTICS
0.3
0.4
0.3
0.2
0.1
0
T
= +25°C
A
T
= +25°C
A
V
V
V
= +5V
= 0V
DD
SS
V
V
V
= +15V
= –15V
DD
SS
0.2
0.1
= 0V
VREFLO
= –10V
VREFLO
0
–0.1
–0.2
–0.3
–0.1
–0.2
–0.3
–0.4
–6
–4
–2
0
2
4
6
8
10
12
14
1.5
2.0
2.5
3.0
3.5
V
(V)
V
(V)
VREFHI
VREFHI
Figure 6. DNL vs. VVREFHI (±±5 V)
Figure 9. INL vs. VVREFHI (+5 V)
0.7
0.5
0.10
0.05
0
x + 3σ
T
= +25°C
= +5V
A
V
V
V
DD
V
V
V
V
= +15V
= –15V
DD
SS
= 0V
SS
VREFLO
= 0V
= +10V
VREFHI
0.3
= –10V
VREFLO
–0.05
–0.10
–0.15
x
0.1
–0.1
–0.20
–0.25
–0.3
–0.5
x – 3σ
0
200
400
600
800
1000
–0.30
1.5
2.0
2.5
3.0
3.5
t
= HOURS OF OPERATION AT 125°C
CURVES NOT NORMALIZED
V
(V)
VREFHI
Figure 7. DNL vs. VVREFHI (+5 V)
Figure ±0. Full-Scale Error vs. Time Accelerated by Burn-In
1.2
0.3
0.2
x + 3σ
1.0
0.8
0.6
0.4
V
V
V
V
= +15V
= –15V
DD
SS
= +10V
= –10V
0.1
VREFHI
VREFLO
x
0
–0.1
–0.2
–0.3
T
= +25°C
A
V
V
V
= +15V
= –15V
DD
SS
0.2
0
= –10V
VREFLO
x – 3σ
0
200
t
400
600
800
1000
–6
–4
–2
0
2
4
6
8
10
12
14
= HOURS OF OPERATION AT 125°C
CURVES NOT NORMALIZED
V
(V)
VREFHI
Figure 8. INL vs. VREFHI (±±5 V)
Figure ±±. Zero-Scale Error vs. Time Accelerated by Burn-In
Rev. C | Page 9 of 23
DAC8420
Data Sheet
1.5
1.0
0.5
0
0.2
T
= +25°C
A
V
V
V
V
= +15V
= –15V
DD
SS
V
V
V
V
= +5V
= 0V
DD
SS
0.1
= +10V
= –10V
VREFHI
= +2.5V
= 0V
VREFHI
VREFLO
0
–0.1
–0.2
VREFLO
DAC C
DAC D
DAC A
–0.5
–0.3
–0.4
–0.5
–0.6
–1.0
–1.5
DAC B
0
500 1000 1500 2000 2500 3000 3500 4000 4500
DIGITAL INPUT CODE
–75
–50
–25
0
25
50
75
100
125
TEMPERATURE (°C)
Figure ±2. Full-Scale Error vs. Temperature
Figure ±5. Channel-to-Channel Matching
1.2
13
12
T
= +25°C
= +15V
V
V
V
V
= +15V
= –15V
= +10V
A
DD
SS
V
V
V
DD
1.0
= –15V
SS
VREFLO
VREFHI
11
10
9
= –10V
= –10V
VREFLO
0.8
0.6
0.4
DAC B
DAC C
DAC D
DAC A
8
7
0.2
0
6
–0.2
–0.4
5
4
–7
–5
–3
–1
0
1
3
5
7
9
11
13
–75
–50
–25
0
25
50
C)
75
100
125
V
(V)
TEMPERATURE (
°
VREFHI
Figure ±3. Zero-Scale Error vs. Temperature
Figure ±6. IDD vs. VVREFHI, All DACs High
0.9
0.7
0.8
T
= +25°C
= +15V
T
= +25°C, –55°C, 125°C
= +15V
A
A
0.7
0.6
V
V
V
V
V
V
V
V
DD
DD
= –15V
= –15V
SS
SS
= +10V
= –10V
= +10V
= –10V
0.5
VREFHI
VREFHI
0.5
0.4
VREFLO
VREFLO
0.3
0.3
0.1
0.2
0.1
–0.1
–0.3
–0.5
–0.7
–0.9
0
–0.1
–0.2
–0.3
–0.4
0
500 1000 1500 2000 2500 3000 3500 4000 4500
DIGITAL INPUT CODE
0
500 1000 1500 2000 2500 3000 3500 4000 4500
DIGITAL INPUT CODE
Figure ±4. Channel-to-Channel Matching
Figure ±7. INL vs. Code
Rev. C | Page 10 of 23
Data Sheet
DAC8420
1.5
31.25mV
LD
T
= +25°C
A
1.0
0.5
V
V
V
V
= +15V
= –15V
DD
SS
= +10V
= –10V
VREFHI
VREFLO
0
T
= +25°C
4.88mV
A
V
V
V
V
= +15V
= –15V
1 LSB
0mV
DD
SS
–0.5
–1.0
= +10V
= –10V
VREFHI
VREFLO
–18.75mV
0
500 1000 1500 2000 2500 3000 3500 4000 4500
DIGITAL INPUT CODE
–9.8µs
10µs/DIV
90.2µs
tSETT
13µs
Figure ±8. IVREFHI vs. Code
Figure 2±. Positive Settling Time (±±5 V)
–2.50µV
LD
43.75mV
CLR
T
= +25°C
= +5V
T
= +25°C
A
A
V
V
V
V
V
V
V
V
= +15V
= –15V
DD
DD
SS
= –5V
SS
= +2.5V
= –2.5V
= +10V
= –10V
VREFHI
VREFHI
1.22mV
1 LSB
0mV
VREFLO
VREFLO
0mV
1 LSB
–4.88mV
–10.25mV
–6.25mV
–9.8µs
–4.9µs
5µs/DIV
45.1µs
10µs/DIV
90.2µs
tSETT
8µs
tSETT
13µs
Figure ±9. Positive Settling Time (±5 V)
Figure 22. Negative Settling Time (±±5 V)
6.5mV
CLR
5V
T
= +25°C
A
V
V
V
V
= +5V
= –5V
DD
SS
T
= +25°C
A
V
V
V
V
= +5V
= –5V
= +2.5V
= –2.5V
DD
SS
VREFHI
VREFLO
= +2.5V
= –2.5V
VREFHI
VREFLO
+1V/DIV
0
0mV
1 LSB
1.22mV
–5V
–47.6µs
3.5mV
–4.9µs
20µs/DIV
152.4µs
5µs/DIV
45.1µs
V
µs
V
µs
SR
= 1.65
SR
= 1.17
RISE
FALL
tSETT
8µs
Figure 20. Negative Settling Time (±5 V)
Figure 23. Slew Rate (±5 V)
Rev. C | Page 11 of 23
DAC8420
Data Sheet
25V
LD
6
I
DD
4
2
CLR
V
V
V
V
= +15V
= –15V
DD
SS
+5V/DIV
0
= +10V
= –10V
VREFHI
0
VREFLO
ALL DACS HIGH (FULL SCALE)
T
= +25°C
A
V
V
V
V
= +15V
= –15V
DD
SS
–2
–4
–6
= +10V
= –10V
VREFHI
VREFLO
I
SS
–25V
–33.6µs
–75
0
75
150
20µs/DIV
166.4µs
V
µs
V
µs
SR
RISE
= 1.9
SR = 2.02
FALL
TEMPERATURE (°C)
Figure 24. Slew Rate (±±5 V)
Figure 27. Power Supply Current vs. Temperature
VOUTA THROUGH VOUTD
T
= +25°C
A
V
V
V
V
= +15V
= –15V
DD
SS
10
0
= +10V
= –10V
VREFHI
VREFLO
–10
–20
–30
DATA = 0x800
T
= +25°C
A
V
V
V
V
= +15V
= –15V
DD
SS
= 0 ±100mV
VREFHI
= –10V
VREFLO
ALL BITS HIGH 200mV p-p
5V/DIV
10
100
1k
10k
100k
1M
10M
FREQUENCY (Hz)
Figure 25. Small-Signal Response
Figure 28. DAC Output Current vs. VOUTx
100
10
8
90
80
70
60
50
40
30
20
10
0
6
4
T
= +25°C
A
T = +25°C
A
DATA = 0x000
V
V
V
V
= +15V
= –15V
DD
SS
V
V
V
V
= +15V ±1V
= –15V
DD
2
SS
= +10V
= –10V
VREFHI
= +10V
= –10V
VREFHI
VREFLO
VREFLO
DATA = 0xFFF OR 0x000
0
10
10
100
1k
10k
100k
1M
100
1k 10k
FREQUENCY (Hz)
LOAD RESISTANCE (Ω)
Figure 26. PSRR vs. Frequency
Figure 29. Output Swing vs. Load Resistance
Rev. C | Page 12 of 23
Data Sheet
DAC8420
THEORY OF OPERATION
INTRODUCTION
USING CLR AND CLSEL
The DAC8420 is a quad, voltage-output 12-bit DAC with a serial
digital input capable of operating from a single 5 V supply. The
straightforward serial interface can be connected directly to
most popular microprocessors and microcontrollers, and can
accept data at a 10 MHz clock rate when operating from 15 V
supplies. A unique voltage reference structure ensures maximum
utilization of the DAC output resolution by allowing the user to
set the zero-scale and full-scale output levels within the supply
rails. The analog voltage outputs are fully buffered, and are
capable of driving a 2 kΩ load. Output glitch impulse during
major code transitions is a very low 64 nV-s (typ).
CLR
The clear ( ) control allows the user to perform an asyn-
CLR
chronous reset function. Asserting
loads all four DAC
data-word registers, forcing the DAC outputs to either zero
scale (0x000) or midscale (0x800), depending on the state of
CLSEL as shown in Table 6. The clear function is asynchronous
CS
CLR
and totally independent of . When
returns high, the
LD
DAC outputs remain latched at the reset value until
is
strobed, reloading the individual DAC data-word registers
with either the data held in the serial input register prior to the
reset or with new data loaded through the serial interface.
Table 7. DAC Address Word Decode Table
DIGITAL INTERFACE OPERATION
A1
A0
DAC Addressed
CS
The serial input of the DAC8420, consisting of , SDI, and
LD
,
0
0
DAC A
is easily interfaced to a wide variety of microprocessor serial ports.
CS
0
1
DAC B
While
is low, the data presented to the input SDI is shifted
1
0
DAC C
into the internal serial-to-parallel shift register on the rising
edge of the clock, with the address MSB first, data LSB last, as
shown in Table 6 and in the timing diagram (Figure 2). The
data format, shown in Table 8, is two bits of DAC address and
two don’t care fill bits, followed by the 12-bit DAC data-word.
Once all 16 bits of the serial data-word have been input, the
1
1
DAC D
PROGRAMMING THE ANALOG OUTPUTS
The unique differential reference structure of the DAC8420
allows the user to tailor the output voltage range precisely to
the needs of the application. Instead of spending DAC resolu-
tion on an unused region near the positive or negative rail, the
DAC8420 allows the user to determine both the upper and
lower limits of the analog output voltage range. Thus, as shown
in Table 9 and Figure 30, the outputs of DAC A through DAC D
range between VREFHI and VREFLO, within the limits specified
in the Specifications section. Note also that VREFHI must be
greater than VREFLO.
LD
load control
is strobed and the word is parallel-shifted out
onto the internal data bus. The two address bits are decoded
and used to route the 12-bit data-word to the appropriate DAC
data register (see the Applications section).
CORRECT OPERATION OF CS AND CLK
CS
In Table 6, the control pins CLK and
require some attention
during a data load cycle. Since these two inputs are fed to the
V
DD
same logical OR gate, the operation is in fact identical. The user
must take care to operate them accordingly to avoid clocking in
false data bits. In the timing diagram, CLK must be halted high
2.5V MIN
V
VREFHI
0xFFF
CS
or
must be brought high during the last high portion of the
CLK following the rising edge that latched in the last data bit.
CS
1 LSB
Otherwise, an additional rising edge is generated by
rising
2.5V MIN
CS
while CLK is low, causing
to act as the clock and allowing a
false data bit into the serial input register. The same issue must
also be considered in the beginning of the data load sequence.
0x000
–10V MIN
V
VREFLO
0V MIN
V
SS
Figure 30. Output Voltage Range Programming
Table 8.
(FIRST)
(LAST)
B15
B0
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
A1
A0
NC
NC
D11
(MSB)
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
—Address Word—
—DAC Data-Word—
(LSB)
Rev. C | Page 13 of 23
DAC8420
Data Sheet
Table 9. Analog Output Code
DAC Data-Word (Hex)
0xFFF
VOUT
Note
Full-scale output
Midscale + 1
Midscale
(VREFHI −VREFLO)
4096
(VREFHI −VREFLO)
4096
(VREFHI −VREFLO)
4096
(VREFHI −VREFLO)
4096
VREFLO +
× 4095
× 2049
× 2048
× 2047
×0
0x801
0x800
0x7FF
0x000
VREFLO +
VREFLO +
VREFLO +
VREFLO +
Midscale − 1
Zero scale
(VREFHI −VREFLO)
4096
Rev. C | Page 14 of 23
Data Sheet
DAC8420
POWER-UP SEQUENCE
VREFHI INPUT REQUIREMENTS
To prevent a CMOS latch-up condition, power up VDD, VSS,
and GND prior to any reference voltages. The ideal power-up
sequence is GND, VSS, VDD, VREFHI, VREFLO, and digital
inputs. Noncompliance with the power-up sequence over an
extended period can elevate the reference currents and eventually
damage the device. On the other hand, if the noncompliant
power-up sequence condition is as short as a few milliseconds,
the device can resume normal operation without being damaged
once VDD/VSS is powered.
The DAC8420 utilizes a unique, patented DAC switch driver
circuit that compensates for different supply, reference voltage,
and digital code inputs. This ensures that all DAC ladder switches
are always biased equally, ensuring excellent linearity under all
conditions. Thus, as shown in Table 1, the VREFHI input of the
DAC8420 requires both sourcing and sinking current capabili-
ties from the reference voltage source. Many positive voltage
references are intended as current sources only and offer little
sinking capability. The user must consider references such as
the AD584, AD586, AD587, AD588, AD780, and REF43 for
such an application.
Rev. C | Page 15 of 23
DAC8420
Data Sheet
APPLICATIONS
In the case of 5 V only systems, it is desirable to use the same 5 V
supply for both the analog circuitry and the digital portion of
the circuit. Unfortunately, the typical 5 V supply is extremely
noisy due to the fast edge rates of the popular CMOS logic families,
which induce large inductive voltage spikes, and busy micro-
controller or microprocessor buses, and therefore commonly have
large current spikes during bus activity. However, by properly
filtering the supply as shown in Figure 32, the digital 5 V supply
can be used. The inductors and capacitors generate a filter that
not only rejects noise due to the digital circuitry, but also filters
out the lower frequency noise of switch mode power supplies.
The analog supply must be connected as close as possible to the
origin of the digital supply to minimize noise pickup from the
digital section.
POWER SUPPLY BYPASSING AND GROUNDING
In any circuit where accuracy is important, careful consid-
eration of the power supply and ground return layout helps to
ensure the rated performance. The DAC8420 has a single ground
pin that is internally connected to the digital section as the logic
reference level. The first thought may be to connect this pin to
digital ground; however, in large systems digital ground is often
noisy because of the switching currents of other digital circuitry.
Any noise that is introduced at the ground pin can couple into
the analog output. Thus, to avoid error-causing digital noise in the
sensitive analog circuitry, the ground pin must be connected to
the system analog ground. The ground path (circuit board trace)
must be as wide as possible to reduce any effects of parasitic
inductance and ohmic drops. A ground plane is recommended
if possible. The noise immunity of the on-board digital circuitry,
typically in the hundreds of millivolts, is well able to reject the
common-mode noise typically seen between system analog and
digital grounds. Finally, the analog and digital ground must be
connected to each other at a single point in the system to provide a
common reference. This is preferably done at the power supply.
FERRITE BEADS:
2 TURNS, FAIR-RITE
#2677006301
TTL/CMOS
LOGIC
CIRCUITS
+5V
0.1µF
+
+
100µF
ELECT.
10µF TO 22µF
TANT.
CER.
+5V
RETURN
Good grounding practice is also essential to maintaining analog
performance in the surrounding analog support circuitry. With
two reference inputs and four analog outputs capable of moderate
bandwidth and output current, there is a significant potential
for ground loops. Again, a ground plane is recommended as the
most effective solution to minimizing errors due to noise and
ground offsets.
+5V
POWER SUPPLY
Figure 32. Single-Supply Analog Supply Filter
ANALOG OUTPUTS
The DAC8420 features buffered analog voltage outputs capable
of sourcing and sinking up to 5 mA when operating from 15 V
supplies, eliminating the need for external buffer amplifiers in most
applications while maintaining specified accuracy over the rated
operating conditions. The buffered outputs are simply an
operational amplifier connected as a voltage follower, and thus
have output characteristics very similar to the typical operational
amplifier. These amplifiers are short-circuit protected. The user
must verify that the output load meets the capabilities of the device,
in terms of both output current and load capacitance. The
DAC8420 is stable with capacitive loads up to 2 nF typically.
However, any capacitive load increases the settling time, and
must be minimized if speed is a concern.
1
+V
V
DD
S
10µF
0.1µF
8
9
–V
V
GND
S
SS
10µF
0.1µF
10µF = TANTALUM
0.1µF = CERAMIC
The output stage includes a P-channel MOSFET to pull the output
voltage down to the negative supply. This is very important in
single-supply systems where VREFLO usually has the same
potential as the negative supply. With no load, the zero-scale output
voltage in these applications is less than 500 μV typically, or less
than 1 LSB when VVREFHI = 2.5 V. However, when sinking current,
this voltage does increase because of the finite impedance of the
output stage. The effective value of the pull-down resistor in the
output stage is typically 320 Ω. With a 100 kΩ resistor connected to
5 V, the resulting zero-scale output voltage is 16 mV. Thus, the best
single-supply operation is obtained with the output load connected
to ground, so the output stage does not have to sink current.
Figure 3±. Recommended Supply Bypassing Scheme
The DAC8420 must have ample supply bypassing, located as
close to the package as possible. Figure 31 shows the recom-
mended capacitor values of 10 μF in parallel with 0.1 μF. The
0.1 μF capacitor must have low effective series resistance (ESR) and
effective series inductance (ESI) (such as any common ceramic
type capacitor), which provide a low impedance path to ground
at high frequencies to handle transient currents due to internal
logic switching. To preserve the specified analog performance of
the device, the supply must be as noise free as possible.
Rev. C | Page 16 of 23
Data Sheet
DAC8420
Like all amplifiers, the DAC8420 output buffers do generate
voltage noise, 52 nV/√Hz typically. This is easily reduced by
adding a simple RC low-pass filter on each output.
The AD588 provides both voltages and needs no external
components. Additionally, the device is trimmed in production
for 12-bit accuracy over the full temperature range without user
calibration. Performing a clear with the reset select CLSEL high
allows the user to easily reset the DAC outputs to midscale, or
0 V in these applications.
REFERENCE CONFIGURATION
The two reference inputs of the DAC8420 allow a great deal
of flexibility in circuit design. The user must take care, however,
to observe the minimum voltage input levels on VREFHI and
VREFLO to maintain the accuracy shown in the data sheet.
These input voltages can be set anywhere across a wide range
within the supplies, but must be a minimum of 2.5 V apart in
any case (see Figure 30). A wide output voltage range can be
obtained with 5 V references, which can be provided by the
AD588 as shown in Figure 33. Many applications utilize the
DACs to synthesize symmetric bipolar waveforms, which
require an accurate, low drift bipolar reference.
When driving the reference inputs VREFHI and VREFLO, it is
important to note that VREFHI both sinks and sources current,
and that the input currents of both are code dependent. Many
voltage reference products have a limited current sinking capability
and must be buffered with an amplifier to drive VREFHI in order
to maintain overall system accuracy. The input VREFLO, however,
has no such requirement.
+15V SUPPLY
VREFHI
1µF
7
6
4
3
0.1µF
+5V
5
1
AD588
A3
R
DAC8420
B
+5V
–5V
DAC A
DAC B
DAC C
7
6
3
VOUTA
VOUTB
VOUTC
1
A1
R1
14
15
R4
A4
R2
R5
+15V
SUPPLY
+V
S
2
DIGITAL
CONTROLS
R3
R6
0.1µF
0.1µF
A2
DAC D
4
2
VOUTD
0.1µF
SYSTEM
GROUND
–V 16
S
5
9
10
8
12
11 13
10 11 12 14 15 16
DIGITAL INPUTS
9
8
–15V
SUPPLY
VREFLO
–5V
GND
–15V SUPPLY
Figure 33. ±±0 V Bipolar Reference Configuration Using the AD588
Rev. C | Page 17 of 23
DAC8420
Data Sheet
For a single 5 V supply, VVREFHI is limited to at most 2.5 V, and
must always be at least 2.5 V less than the positive supply to ensure
linearity of the device. For these applications, the REF43 is an
excellent low drift 2.5 V reference that consumes only 450 μA
(max). It works well with the DAC8420 in a single 5 V system as
shown in Figure 34.
LD
One opto-isolated line ( ) can be eliminated from this circuit
by adding an inexpensive 4-bit TTL counter to generate the load
pulse for the DAC8420 after 16 clock cycles. The counter is used
to count the number of clock cycles loading serial data to the
DAC8420. After all 16 bits have been clocked into the converter,
the counter resets, and a load pulse is generated on Clock 17. In
either circuit, the serial interface of the DAC8420 provides a simple,
low cost method of isolating the digital control.
+5V SUPPLY
REF43
2
V
IN
+5V SUPPLY
HIGH VOLTAGE
ISOLATION
0.1µF
2.5V
4
6
GND
V
OUT
5V
5V
VREFHI
0.1µF
REG
5
1
POWER
DAC8420
DAC A
7
6
3
VOUTA
VOUTB
VOUTC
5V
10kΩ
+5V
REF43
2
4
V
IN
DAC B
DAC C
6
V
OUT
GND
LD
SCLK
SDI
5V
2.5V
5V
10kΩ
0.1µF
0.1µF
DIGITAL
5
1
5V
10kΩ
CONTROLS
VREFHI
CLR
VDD
DAC D
4
2
VOUTD
15
16
14
12
11
10
7
VOUTA
CLSEL
LD
10 11 12 14 15 16
DIGITAL INPUTS
9
8
6
3
VOUTB
VOUTC
GND
VREFLO
DAC8420
CS
5V
10kΩ
Figure 34. 5 V Single-Supply Operation Using REF43
CLK
SDI
2
VOUTD
ISOLATED DIGITAL INTERFACE
VREFLO VSS GND
Because the DAC8420 is ideal for generating accurate voltages
in process control and industrial applications, due to noise, from
the central controller; it can be necessary to isolate it from the
central controller. This can be easily achieved by using opto-
isolators, which are commonly used to provide electrical isolation
in excess of 3 kV. Figure 35 shows a simple 3-wire interface scheme
for controlling the clock, data, and load pulse. For normal
4
8
9
Figure 35. Opto-lsolated 3-Wire Interface
CS
operation,
always selected. The resistor and capacitor on the
a power-on reset with 10 ms time constant. The three opto-
LD
is tied permanently low so that the DAC8420 is
CLR
pin provide
isolators are used for the SDI, CLK, and
lines.
Rev. C | Page 18 of 23
Data Sheet
DAC8420
5V SUPPLY
REF43
VINA
5V
2
4
V
IN
5V SUPPLY
0.1µF
2.5V
0.1µF
6
GND
V
OUT
5V
604Ω
0.1µF
VREFHI
3
5
1
CMP04
VOUTA
VOUTB
VOUTC
DAC8420
5
4
DAC A
7
6
3
RED LED
5V
C1
C2
C3
2
1
OUT A
DAC B
DAC C
7
6
604Ω
9
8
RED LED
DIGITAL
CONTROLS
14
13
OUT B
VOUTD
DAC D
4
2
11
10
C4
12
10 11 12 14 15 16
DIGITAL INPUTS
9
8
GND
VREFLO VSS
VINB
Figure 36. Dual Programmable Window Comparator
DUAL WINDOW COMPARATOR
PC2
CLSEL
PC1
PC0
CLR
CS
Often a comparator is needed to signal an out-of-range warning.
Combining the DAC8420 with a quad comparator such as the
CMP04 provides a simple dual window comparator with adjustable
trip points as shown in Figure 36. This circuit can be operated with
either a dual supply or a single supply. For the A input channel,
DAC B sets the low trip point, and DAC A sets the upper trip
point. The CMP04 has open-collector outputs that are connected
together in a wire-OR’ed configuration to generate an out-of-
range signal. For example, when VINA goes below the trip point
set by DAC B, Comparator C2 pulls the output down, turning
on the red LED. The output can also be used as a logic signal for
further processing.
MC68HC11*
DAC8420*
(PD5) SS
SCK
LD
CLK
SDI
MOSI
*ADDITIONAL PINS OMITTED FOR CLARITY.
Figure 37. MC68HC11 Microcontroller Interface
For correct operation, the MC68HC11 must be configured
such that the CPOL bit and CPHA bit are both set to 1. In this
configuration, serial data on MOSI of the MC68HC11 is valid
on the rising edge of the clock, which is the required timing for
the DAC8420. Data is transmitted in 8-bit bytes (MSB first), with
only eight rising clock edges occurring in the transmit cycle. To
load data to the input register of the DAC8420, PC0 is taken low
and held low during the entire loading cycle. The first eight bits
are shifted in address first, immediately followed by another eight
bits in the second least-significant byte to load the complete 16-
bit word. At the end of the second byte load, PC0 is then taken
high. To prevent an additional advancing of the internal shift
register, SCK must already be asserted before PC0 is taken high.
To transfer the contents of the input shift register to the DAC
MC68HC11 MICROCONTROLLER INTERFACING
Figure 37 shows a serial interface between the DAC8420 and
the MC68HC11 8-bit microcontroller. The SCK output of the
port outputs the serial data to load into the SDI input of the
DAC. The port lines (PD5, PC0, PC1, and PC2) provide the
controls to the DAC as shown.
LD
register, PD5 is then taken low, asserting the
and completing the loading process. PD5 must return high before
CLR
input of the DAC
the next load cycle begins. The
input of the DAC8420
(controlled by the output PC1) provides an asynchronous clear
function.
Rev. C | Page 19 of 23
DAC8420
Data Sheet
DAC8420 TO M68HC11 INTERFACE ASSEMBLY PROGRAM
* M68HC11 Register Definitions
PORTC EQU $1003 Port C control register
* “0,0,0,0;0,CLSEL,CLR,CS”
DDRC EQU $1007 Port C data direction
PORTD EQU $1008 Port D data register
* “0,0,LD,SCLK;SDI,0,0,0”
DDRD EQU $1009 Port D data direction
SPCR EQU $1028 SPI control register
* “SPIE,SPE,DWOM,MSTR;CPOL,CPHA,SPR1,SPR0”
SPSR EQU $1029 SPI status register
* “SPIF,WCOL,0,MODF;0,0,0,0”
SPDR EQU $102A SPI data register; Read-Buffer; Write-Shifter
*
* SDI RAM variables: SDI1 is encoded from 0 (Hex) to CF (Hex)
* To select: DAC A – Set SDI1 to $0X
DAC B – Set SDI1 to $4X
DAC C – Set SDI1 to $8X
DAC D – Set SDI1 to $CX
SDI2 is encoded from 00 (Hex) to FF (Hex)
* DAC requires two 8-bit loads – Address + 12 bits
SDI1 EQU $00 SDI packed byte 1 “A1,A0,0,0;MSB,DB10,DB9,DB8”
SDI2 EQU $01 SDI packed byte 2
“DB7,DB6,DB5,DB4;DB3,DB2,DB1,DB0”
* Main Program
ORG $C000 Start of user’s RAM in EVB
INIT LDS #$CFFF Top of C page RAM
* Initialize Port C Outputs
* Initialize SPI Interface
LDAA #$5F
STAA SPCR SPI is Master,CPHA=1,CPOL=1,Clk rate=E/32
* Call update subroutine
BSR UPDATE Xfer 2 8-bit words to DAC-8420
JMP $E000 Restart BUFFALO
* Subroutine UPDATE
UPDATE PSHX Save registers X, Y, and A
PSHY
PSHA
* Enter Contents of SDI1 Data Register (DAC# and 4 MSBs)
LDAA #$80 1,0,0,0;0,0,0,0
STAA SDI1 SDI1 is set to 80 (Hex)
* Enter Contents of SDI2 Data Register
LDAA #$00 0,0,0,0;0,0,0,0
STAA SDI2 SDI2 is set to 00 (Hex)
LDX #SDI1 Stack pointer at 1st byte to send via SDI
LDY #$1000 Stack pointer at on-chip registers
* Clear DAC output to zero
BCLR PORTC,Y $02 Assert CLR
BSET PORTC,Y $02 Deassert CLR
* Get DAC ready for data input
BCLR PORTC,Y $01 Assert CS
TFRLP LDAA 0,X Get a byte to transfer via SPI
STAA SPDR Write SDI data reg to start xfer
WAIT LDAA SPSR Loop to wait for SPIF
BPL WAIT SPIF is the MSB of SPSR
*
(when SPIF is set, SPSR is negated)
Increment counter to next byte for xfer
LDAA #$07 0,0,0,0;0,1,1,1
* CLSEL-Hi, CLR-Hi, CS-Hi
INX
CPX #SDI2+ 1 Are we done yet ?
BNE TFRLP If not, xfer the second byte
* To reset DAC to ZERO-SCALE, set CLSEL-Lo ($03)
* To reset DAC to MID-SCALE, set CLSEL-Hi ($07)
STAA PORTC Initialize Port C Outputs
LDAA #$07 0,0,0,0;0,1,1,1
STAA DDRC CLSEL, CLR, and CS are now enabled as outputs
* Initialize Port D Outputs
LDAA #$30 0,0,1,1;0,0,0,0
* LD-Hi,SCLK-Hi,SDI-Lo
STAA PORTD Initialize Port D Outputs
LDAA #$38 0,0,1,1;1,0,0,0
* Update DAC output with contents of DAC register
BCLR PORTD,Y 520 Assert LD
BSET PORTD,Y $20 Latch DAC register
BSET PORTC,Y $01 De-assert CS
PULA When done, restore registers X, Y & A
PULY
PULX
RTS
** Return to Main Program **
STAA DDRD LD,SCLK, and SDI are now enabled as outputs
Rev. C | Page 20 of 23
Data Sheet
DAC8420
OUTLINE DIMENSIONS
0.775
0.755
0.735
9
8
16
1
0.280
0.250
0.240
PIN 1
INDICATOR
TOP VIEW
SIDE VIEW
0.325
0.310
0.300
0.100
BSC
0.195
0.130
0.115
0.210
MAX
0.015
0.150
0.130
0.115
0.015
GAUGE
PLANE
MIN
END VIEW
0.012
0.010
0.008
SEATING
PLANE
0.021
0.022
0.430
MAX
0.018
0.015
0.016
0.011
0.070
0.060
0.055
0.045
0.039
0.030
COMPLIANT TO JEDEC STANDARDS MS-001-BB
Figure 38. ±6-Lead Plastic Dual In-Line Package [PDIP]
Narrow Body
(N-±6)
Dimensions shown in inches
10.50 (0.4134)
10.10 (0.3976)
16
1
9
7.60 (0.2992)
7.40 (0.2913)
10.65 (0.4193)
8
10.00 (0.3937)
0.75 (0.0295)
0.0098)
1.27 (0.0500)
BSC
45°
2.65 (0.1043)
2.35 (0.0925)
0.25 (
0.30 (0.0118)
0.10 (0.0039)
8°
0°
COPLANARITY
0.10
SEATING
PLANE
0.51 (0.0201)
0.31 (0.0122)
1.27 (0.0500)
0.40 (0.0157)
0.33 (0.0130)
0.20 (0.0079)
COMPLIANT TO JEDEC STANDARDS MS-013-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 39. ±6-Lead Standard Small Outline Package [SOIC_W]
Wide Body
(RW-±6)
Dimensions shown in millimeters and (inches)
Rev. C | Page 21 of 23
DAC8420
Data Sheet
0.005 (0.13) MIN
0.098 (2.49) MAX
9
16
0.310 (7.87)
0.220 (5.59)
1
8
PIN 1
0.100 (2.54) BSC
0.320 (8.13)
0.290 (7.37)
0.840 (21.34) MAX
0.060 (1.52)
0.015 (0.38)
0.200 (5.08)
MAX
0.150
(3.81)
MIN
0.200 (5.08)
0.125 (3.18)
0.015 (0.38)
0.008 (0.20)
SEATING
PLANE
15°
0°
0.070 (1.78)
0.030 (0.76)
0.023 (0.58)
0.014 (0.36)
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 40. ±6-Lead Ceramic Dual In-Line Package [CERDIP]
(Q-±6)
Dimensions shown in inches and (millimeters)
ORDERING GUIDE
Model1
Temperature Range
Package Description
Package Option
INL2 ( LSB)
DAC8420EPZ
DAC8420ES
DAC8420ESZ
DAC8420ESZ-REEL
DAC8420FPZ
DAC8420FQ
DAC8420FS
DAC8420FSZ
DAC8420FSZ-REEL
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
16-Lead Plastic Dual In-Line Package [PDIP]
16-Lead Standard Small Outline Package [SOIC_W]
16-Lead Standard Small Outline Package [SOIC_W]
16-Lead Standard Small Outline Package [SOIC_W]
16-Lead Plastic Dual In-Line Package [PDIP]
16-Lead Ceramic Dual In-Line Package [CERDIP]
16-Lead Standard Small Outline Package [SOIC_W]
16-Lead Standard Small Outline Package [SOIC_W]
16-Lead Standard Small Outline Package [SOIC_W]
N-16
0.5
0.5
0.5
0.5
1.0
1.0
1.0
1.0
1.0
RW-16
RW-16
RW-16
N-16
Q-16
RW-16
RW-16
RW-16
1 Z = RoHS Compliant Part.
2 INL measured at VDD = +15 V and VSS = −15 V.
Rev. C | Page 22 of 23
Data Sheet
NOTES
DAC8420
©2003–2016 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D00275-0-9/16(C)
Rev. C | Page 23 of 23
相关型号:
DAC8420ES-REEL
QUAD, SERIAL INPUT LOADING, 8 us SETTLING TIME, 12-BIT DAC, PDSO16, MS-013AA, SOIC-16
ROCHESTER
DAC8420ESZ
QUAD, SERIAL INPUT LOADING, 8 us SETTLING TIME, 12-BIT DAC, PDSO16, ROHS COMPLIANT, MS-013AA, SOIC-16
ROCHESTER
©2020 ICPDF网 联系我们和版权申明