AD9774AS [ADI]
14-Bit, 32 MSPS TxDAC⑩ with 4x Interpolation Filters; 14位， 32 MSPS TxDAC⑩ 4倍内插滤波器
| 型号： | AD9774AS |
| 厂家： | 
ADI |
| 描述： | 14-Bit, 32 MSPS TxDAC⑩ with 4x Interpolation Filters |
| 文件： | 总24页 (文件大小：316K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
14-Bit, 32 MSPS TxDAC+™
with 4
؋
Interpolation Filters a
AD9774
FEATURES
FUNCTIONAL BLOCK DIAGRAM
Single 3 V or 5 V Supply
14-Bit DAC Resolution and Input Data Width
32 MSPS Input Data Rate at 5 V
13.5 MHz Reconstruction Bandwidth
12 ENOBS @ 1 MHz
77 dBc SFDR @ 5 MHz
4
؋
Interpolation Filter PLL
DIVIDE
VCO
IN/EXT
PLL
CLK4
؋
IN PLLLOCK ENABLE PLLCOM
LPF
AD9774
PLL CLOCK
MULTIPLIER
CLK IN/OUT
1
؋
2
؋
4
؋
PLLVDD
4
؋
69 dB Image Rejection
14
14
14
14
DATA
INPUTS
(DB13-DB0)
IOUTA
IOUTB
EDGE
TRIGGERED
LATCHES
14-BIT
DAC
2
؋
2
؋
84% Passband to Nyquist Ratio
0.002 dB Passband Ripple
23 3/4 Cycle Latency
Internal 4
؋
Clock Multiplier On-Chip 1.20 V Reference
44-Lead MQFP Package
SNOOZE
SLEEP
REFIO
FSADJ
+1.2V REFERENCE
AND CONTROL AMP
REFLO REFCOMP
ICOMP ACOM AVDD
DVDD
DCOM
APPLICATIONS
Communication Transmit Channel:
Wireless Basestations
ADSL/HFC Modems
Direct Digital Synthesis (DDS)
Edge-triggered input latches, a 4× clock multiplier, and a tem-
perature compensated bandgap reference have also been inte-
grated to provide a complete monolithic DAC solution. Flexible
supply options support +3 V and +5 V CMOS logic families.
TTL logic levels can also be accommodated by reducing the
AD9774 digital supply.
PRODUCT DESCRIPTION
The on-chip reference and control amplifier are configured for
maximum accuracy and flexibility. The AD9774 can be driven
by the on-chip reference or by a variety of external reference
voltages. The full-scale current of the AD9774 can be adjusted
over a 2 mA to 20 mA range, thus providing additional gain
ranging capabilities.
The AD9774 is a single supply, oversampling, 14-bit digital-to-
analog converter (DAC) optimized for waveform reconstruction
applications requiring exceptional dynamic range. Manufac-
tured on an advanced CMOS process, it integrates a complete,
low distortion 14-bit DAC with a 4× digital interpolation filter
and clock multiplier. The two-stage, 4× digital interpolation
filter provides more than a six-fold reduction in the complexity
of the analog reconstruction-filter. It does so by multiplying the
input data rate by a factor of four while simultaneously suppressing
the original inband images by more than 69 dB. The on-chip
clock multiplier provides all the necessary clocks. The AD9774
can reconstruct full-scale waveforms having bandwidths as high
as 13.5 MHz when operating at an input data rate of 32 MSPS
and a DAC output rate of 128 MSPS.
The AD9774 is available in a 44-lead MQFP package. It is
specified for operation over the industrial temperature range.
PRODUCT HIGHLIGHTS
1. On-Chip 4× interpolation filter eases analog reconstruction
filter requirements by suppressing the first three images by 69 dB.
2. Low glitch and fast settling time provide outstanding dynamic
performance for waveform reconstruction or digital synthesis
requirements, including communications.
The 14-bit DAC provides differential current outputs to support
differential or single-ended applications. A segmented current
source architecture is combined with a proprietary switching tech-
nique to reduce spurious components and enhance dynamic per-
formance. Matching between the two current outputs ensures
enhanced dynamic performance in a differential output configura-
tion. The differential current outputs may be fed into a transformer
or tied directly to an output resistor to provide two complementary,
single-ended voltage outputs. A differential op amp topology can
also be used to obtain a single-ended output voltage. The output
voltage compliance range is nominally 1.25 V.
3. On-chip, edge-triggered input CMOS latches interface readily
to CMOS and TTL logic families. The AD9774 can support
input data rates up to 32 MSPS.
4. A temperature compensated, 1.20 V bandgap reference is
included on-chip, providing a complete DAC solution. An
external reference may also be used.
5. The current output(s) of the AD9774 can easily be configured
for various single-ended or differential circuit topologies.
6. On-chip clock multiplier generates all the high-speed clocks
required by the internal interpolation filters. Both 2× and 4×
clocks are generated from the lower rate data clock supplied
by the user.
TxDAC+ is a trademark of Analog Devices, Inc.
REV. B
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
Fax: 781/326-8703
World Wide Web Site: http://www.analog.com
© Analog Devices, Inc., 1998
AD9774–SPECIFICATIONS
DC SPECIFICATIONS
(TMIN to TMAX, AVDD = +5 V, PLLVDD = +5 V, DVDD = +5 V, IOUTFS = 20 mA, unless otherwise noted)
Parameter
Min
Typ
Max
Units
RESOLUTION
14
Bits
DC ACCURACY1
Integral Linearity Error (INL)
TA = +25°C
TMIN to TMAX
Differential Nonlinearity (DNL)
TA = +25°C
±4
±3
LSB
LSB
T
MIN to TMAX
Monotonicity (12-Bit)
GUARANTEED OVER RATED SPECIFICATION TEMPERATURE RANGE
ANALOG OUTPUT
Offset Error
Gain Error (Without Internal Reference)
Gain Error (With Internal Reference)
Full-Scale Output Current2
Output Compliance Range
Output Resistance
–0.025
–7
+7.5
+0.025
+7
+7.5
% of FSR
% of FSR
% of FSR
mA
V
kΩ
±1
±1
20
1.25
100
5
Output Capacitance
pF
REFERENCE OUTPUT
Reference Voltage
1.14
0.1
1.20
1
1.26
1.25
V
µA
Reference Output Current3
REFERENCE INPUT
Input Compliance Range
Reference Input Resistance
V
MΩ
1
TEMPERATURE COEFFICIENTS
Unipolar Offset Drift
Gain Drift (Without Internal Reference)
Gain Drift (With Internal Reference)
Reference Voltage Drift
0
ppm of FSR/°C
ppm of FSR/°C
ppm of FSR/°C
ppm of FSR/°C
±50
±100
±100
POWER SUPPLY
AVDD
Voltage Range4
2.7
5.0
26.5
3.2
5.5
32
5
V
mA
mA
Analog Supply Current (IAVDD
Analog Supply Current in SLEEP Mode (IAVDD
)
)
PLLVDD
Voltage Range
Clock Multiplier Supply Current (IPLLVDD
DVDD
Voltage Range
Digital Supply Current at 5 V (IDVDD
Digital Supply Current at 5 V in SNOOZE Mode (IDVDD
2.7
2.7
5.0
13
5.5
17
V
mA
)
5.0
5.5
140.0
50.0
V
5
)
123.0
42.0
62.0
mA
mA
mA
)
5
Digital Supply Current at 3 V (IDVDD
Nominal Power Dissipation
AVDD and DVDD at 3 V6
)
415
1125
mW
mW
% of FSR/V
% of FSR/V
% of FSR/V
AVDD and DVDD at 5 V6
Power Supply Rejection Ratio (PSRR)7 – AVDD
Power Supply Rejection Ratio (PSRR)7 – PLLVDD
Power Supply Rejection Ratio (PSRR)7 – DVDD
–0.2
–0.025
–0.025
+0.2
+0.025
+0.025
OPERATING RANGE
–40
+85
°C
NOTES
1Measured at IOUTA driving a virtual ground.
2Nominal full-scale current, IOUTFS, is 32 × the IREF current.
3Use an external amplifier to drive any external load.
4For operation below 3 V, it is recommended that the output current be reduced to 12 mA or less to maintain optimum performance.
5Measured at fCLOCK = 25 MSPS and fOUT = 1.01 MHz.
6Measured as unbuffered voltage output into 50 Ω RLOAD at IOUTA and IOUTB, fCLOCK = 32 MSPS and fOUT = 12.8 MHz.
7±5% power supply variation.
Specifications subject to change without notice.
–2–
REV. B
AD9774
(TMIN to TMAX, AVDD = +5 V, PLLVDD = +5 V, DVDD = +5 V, IOUTFS = 20 mA, Differential Transformer
Coupled Output, 50 ⍀ Doubly Terminated, unless otherwise noted)
DYNAMIC SPECIFICATIONS
Parameter
Min
Typ
Max
Units
DYNAMIC PERFORMANCE
Maximum Output Update Rate w/DVDD = 5 V
Maximum Output Update Rate w/DVDD = 3 V
Output Settling Time (tST) (to 0.025%)
128
100
MSPS
MSPS
ns
128
35
55
5
2.5
2.5
50
Output Propagation Delay (tPD
Glitch Impulse
)
Clocks1
pV-s
ns
Output Rise Time (10% to 90%)1
Output Fall Time (10% to 90%)1
Output Noise (IOUTFS = 20 mA)
ns
pA/√Hz2
AC LINEARITY TO NYQUIST
Spurious-Free Dynamic Range (SFDR) to Nyquist
fCLOCK = 25 MSPS; fOUT = 1.01 MHz
0 dBFS Output
79
86
75
75
78
77
79
78
dB
dB
dB
dB
dB
dB
dB
dB
–6 dBFS Output
–12 dBFS Output
–18 dBFS Output
fCLOCK = 32 MSPS; fOUT = 1.01 MHz
fCLOCK = 32 MSPS; fOUT = 5.01 MHz
f
f
CLOCK = 32 MSPS; fOUT = 10.01 MHz
CLOCK = 32 MSPS; fOUT = 13.01 MHz
Total Harmonic Distortion (THD)
fCLOCK = 25 MSPS; fOUT = 1.01 MHz; 0 dBFS
Signal-to-Noise Ratio (SNR)
fCLOCK = 25 MSPS; fOUT = 1.01 MHz; 0 dBFS
–75
76
dB
dB
NOTES
1Propagation delay is delay from data input to DAC update.
2Measured single-ended into 50 Ω load.
Specifications subject to change without notice.
(TMIN to TMAX, AVDD = +5 V, PLLVDD = +5 V, DVDD = +5 V, IOUTFS = 20 mA unless otherwise noted)
DIGITAL SPECIFICATIONS
Parameter
Min
Typ
Max
Units
DIGITAL INPUTS
Logic “1” Voltage @ DVDD = +5 V
Logic “1” Voltage @ DVDD = +3 V
Logic “0” Voltage @ DVDD = +5 V
Logic “0” Voltage @ DVDD = +3 V
Logic “1” Current
Logic “0” Current
Input Capacitance
Input Setup Time (tS)
Input Hold Time (tH)
3.5
2.1
5
3
0
0
V
V
V
V
µA
µA
pF
ns
ns
ns
1.3
0.9
+10
+10
–10
–10
5
2.5
1.5
4
Latch Pulsewidth (tLPW
)
DB0–DB11
CLOCK
tS
tH
tLPW
tST
tPD
IOUTA
OR
IOUTB
0.025%
0.025%
Figure 1. Timing Diagram
–3–
REV. B
AD9774–SPECIFICATIONS
(TMIN to TMAX, AVDD = +2.7 V to +5.5 V, DVDD = +2.7 V to +5.5 V, IOUTFS = 20 mA unless
DIGITAL FILTER SPECIFICATIONS otherwise noted)
Parameter
Min
Typ
Max
Units
MAXIMUM INPUT CLOCK RATE (fCLOCK
)
DVDD = 5 V
DVDD = 3 V
32
25
MSPS
MSPS
32
DIGITAL FILTER CHARACTERISTICS
Passband Width1: 0.005 dB
Passband Width: 0.01 dB
Passband Width: 0.1 dB
Passband Width: –3 dB
0.410
0.414
0.420
0.482
fOUT/fCLOCK
fOUT/fCLOCK
fOUT/fCLOCK
fOUT/fCLOCK
LINEAR PHASE (FIR IMPLEMENTATION)
STOPBAND REJECTION
0.591 fCLOCK to 3.419 fCLOCK
0.591 fCLOCK to 1.409 fCLOCK
–69.5
–79.5
dB
dB
GROUP DELAY2
38
Input Clocks
IMPULSE RESPONSE DURATION
–40 dB
–60 dB
53
62
Input Clocks
Input Clocks
NOTES
1Excludes sinx/x characteristic of DAC.
2Defined as the number of data clock cycles between impulse input and peak of output response.
Specifications subject to change without notice.
ABSOLUTE MAXIMUM RATINGS*
With
ORDERING GUIDE
Temperature
Package
Package
Option*
Respect
to
Model
Range
Description
Parameter
Min Max
Units
AD9774AS
AD9774EB
–40°C to +85°C
44-Lead MQFP
Evaluation Board
S-44
AVDD
DVDD
ACOM
DCOM
–0.3 +6.5
–0.3 +6.5
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
°C
°C
°C
*S = Metric Quad Flatpack.
PLLVDD
PLLCOM –0.3 +6.5
ACOM
PLLCOM
PLLCOM
AVDD
PLLVDD
PLLVDD
CLKIN, CLK4×IN
SLEEP, SNOOZE
Digital Inputs
PLL DIVIDE, LPF
PLLLOCK
VCO IN/EXT
IOUTA/IOUTB
REFIO, FSADJ
FSADJ
DCOM
ACOM
DCOM
DVDD
DVDD
AVDD
DVDD
DCOM
DCOM
ACOM
ACOM
ACOM
ACOM
ACOM
ACOM
ACOM
ACOM
–0.3 +0.3
–0.3 +0.3
–0.3 +0.3
–6.5 +6.5
–0.3 +6.5
–0.3 +6.5
–0.3 +6.5
–0.3 DVDD + 0.3
–0.3 DVDD + 0.3
–0.3 PLLVDD + 0.3
–0.3 PLLVDD + 0.3
–0.3 PLLVDD + 0.3
–0.3 AVDD + 0.3
–0.3 AVDD + 0.3
–0.3 AVDD + 0.3
–0.3 AVDD + 0.3
–0.3 +0.3
THERMAL CHARACTERISTIC
Thermal Resistance
44-Lead MQFP
θJA = 53.2°C/W
θJC = 19°C/W
ICOMP
REFCOM
Junction Temperature
Storage Temperature
Lead Temperature
(10 sec)
+150
+150
+300
–65
*Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum ratings
for extended periods may effect device reliability.
–4–
REV. B
AD9774
0
–20
Table I. Integer Filter Coefficients for First Stage Interpola-
tion Filter (55-Tap Halfband FIR Filter)
–40
Lower
Upper
Integer
Coefficient Coefficient Value
–60
H(1)
H(2)
H(3)
H(4)
H(5)
H(6)
H(7)
H(8)
H(55)
H(54)
H(53)
H(52)
H(51)
H(50)
H(49)
H(48)
H(47)
H(46)
H(45)
H(44)
H(43)
H(42)
H(41)
H(40)
H(39)
H(38)
H(37)
H(36)
H(35)
H(34)
H(33)
H(32)
H(31)
H(30)
H(29)
–1
0
3
0
–7
0
15
0
–28
0
49
0
–81
0
128
0
–196
0
295
0
–447
0
706
0
–1274
0
3976
6276
–80
–100
–120
–140
–160
–180
H(9)
0
0.5
1.0
2.0
1.5
FREQUENCY – DC TO 2
؋
f H(10)
H(11)
H(12)
H(13)
H(14)
H(15)
H(16)
H(17)
H(18)
H(19)
H(20)
H(21)
H(22)
H(23)
H(24)
H(25)
H(26)
H(27)
H(28)
CLOCK
Figure 2a. FIR Filter Frequency Response
1.0
0.8
0.6
0.4
0.2
0.0
–0.2
–0.4
0
10
20
30
40
50
60
70
80
TIME – Samples
Figure 2b. FIR Filter Impulse Response
Table II. Integer Filter Coefficients for Second Stage Inter-
polation Filter (23-Tap Halfband FIR Filter)
Lower
Upper
Integer
Coefficient Coefficient Value
H(1)
H(2)
H(3)
H(4)
H(5)
H(6)
H(7)
H(8)
H(9)
H(10)
H(11)
H(12)
H(23)
H(22)
H(21)
H(20)
H(19)
H(18)
H(17)
H(16)
H(15)
H(14)
H(13)
–6
0
37
0
–125
0
316
0
–736
0
2562
4096
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD9774 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
REV. B
–5–
AD9774
PIN FUNCTION DESCRIPTIONS
Pin No.
Name
Description
1, 19, 40, 44 DCOM
Digital Common.
2
3–14
15
16, 17, 42
18, 41
20
DB13
DB12–DB1
DB0
NC
DVDD
CLK IN/OUT
Most Significant Data Bit (MSB).
Data Bits 1–12.
Least Significant Data Bit (LSB).
No Internal Connection.
Digital Supply Voltage (+2.7 V to +5.5 V).
Clock Input when PLL Clock Multiplier enabled. Clock Output when PLL Clock Multiplier
disabled. Data latched on rising edge.
21
22
23
PLLLOCK
CLK4×IN
PLLDIVIDE
Phase Lock Loop Lock Signal. Active High indicates PLL is locked to input clock.
External 4× Clock Input when PLL is disabled. No Connect when internal PLL is active.
PLL Range Control Pin. Connect to PLLCOM if CLKIN is above 10 MSPS. Connect to
PLLVDD if CLKIN is between 10 MSPS and 5.5 MSPS.
24
VCO IN/EXT
Internal Voltage Controlled Oscillator (VCO) Enable/Disable Pin. Connect to PLLVDD to enable
VCO. Connect to PLLCOM to disable VCO and drive CLK4×IN with external VCO output.
25
26
27
28
29
30
LPF
PLL Loop Filter Node. Connect to external VCO control input if internal VCO disabled.
Phase Lock Loop (PLL) Supply Voltage (+2.7 V to +5.5 V). Must be set to similar voltage as DVDD.
Phase Lock Loop Common.
Phase Lock Loop Enable. Connect to PLLVDD to enable. Connect to PLLCOM to disable.
Factory Test. Leave Open.
PLLVDD
PLLCOM
PLLENABLE
UNUSED
REFLO
Reference Ground when Internal 1.2 V Reference Used. Connect to AVDD to disable internal
reference.
31
REFIO
Reference Input/Output. Serves as reference input when internal reference disabled (i.e., tie REFLO
to AVDD). Serves as 1.2 V reference output when internal reference activated (i.e., tie REFLO to
ACOM). Requires 0.1 µF capacitor to ACOM when internal reference activated.
32
33
34
35
36
37
38
39
43
FSADJ
REFCOMP
ACOM
Full-Scale Current Output Adjust.
Noise Reduction Node. Add 0.1 µF to AVDD.
Analog Common.
Analog Supply Voltage (+2.7 V to +5.5 V).
Complementary DAC Current Output. Full-scale current when all data bits are 0s.
DAC Current Output. Full-scale current when all data bits are 1s.
Internal bias node for switch driver circuitry. Decouple to ACOM with 0.1 µF capacitor.
Power-Down Control Input. Active High. Connect to DCOM if not used.
AVDD
IOUTB
IOUTA
ICOMP
SLEEP
SNOOZE
SNOOZE Control Input. Deactivates 4× interpolation filter to reduce digital power consumption
only. Active High. Connect to DCOM if not used.
PIN CONFIGURATION
44 43 42 41 40 39 38 37 36 35 34
33 REFCOMP
DCOM
1
2
3
4
5
6
7
8
9
PIN 1
IDENTIFIER
32
FSADJ
DB13
DB12
31
REFIO
30
DB11
DB10
DB9
REFLO
29
UNUSED
AD9774
TOP VIEW
(Not to Scale)
28
PLLENABLE
DB8
27
26
25
24
23
PLLCOM
PLLVDD
LPF
DB7
DB6
DB5 10
VCO IN/EXT
PLLDIVIDE
11
DB4
12 13 14 15 16 17 18 19 20 21 22
NC = NO CONNECT
–6–
REV. B
AD9774
DEFINITIONS OF SPECIFICATIONS
Settling Time
Linearity Error (Also Called Integral Nonlinearity or INL)
Linearity error is defined as the maximum deviation of the actual
analog output from the ideal output, determined by a straight
line drawn from zero to full scale.
The time required for the output to reach and remain within a
specified error band about its final value, measured from the
start of the output transition.
Glitch Impulse
Differential Nonlinearity (or DNL)
DNL is the measure of the variation in analog value, normalized
to full scale, associated with a 1 LSB change in digital input code.
Asymmetrical switching times in a DAC give rise to undesired
output transients that are quantified by a glitch impulse. It is
specified the net area of the glitch in pV-s.
Monotonicity
Spurious-Free Dynamic Range
A D/A converter is monotonic if the output either increases or
remains constant as the digital input increases.
The difference, in dB, between the rms amplitude of the output
signal and the peak spurious signal over the specified bandwidth.
Offset Error
Total Harmonic Distortion
The deviation of the output current from the ideal of zero is
called offset error. For IOUTA, 0 mA output is expected when
the inputs are all 0s. For IOUTB, 0 mA output is expected
when all inputs are set to 1s.
THD is the ratio of the rms sum of the first six harmonic com-
ponents to the rms value of the measured input signal. It is
expressed as a percentage or in decibels (dB).
Signal-to-Noise Ratio (SNR)
Gain Error
S/N is the ratio of the rms value of the measured output signal
to the rms sum of all other spectral components below the
Nyquist frequency, excluding the first six harmonics and dc.
The value for SNR is expressed in decibels.
The difference between the actual and ideal output span. The
actual span is determined by the output when all inputs are set
to 1s, minus the output when all inputs are set to 0s.
Output Compliance Range
Passband
The range of allowable voltage at the output of a current-output
DAC. Operation beyond the maximum compliance limits may
cause either output stage saturation or breakdown, resulting in
nonlinear performance.
Frequency band in which any input applied therein passes
unattenuated to the DAC output.
Stopband Rejection
The amount of attenuation of a frequency outside the passband
applied to the DAC, relative to a full-scale signal applied at the
DAC input within the passband.
Temperature Drift
Temperature drift is specified as the maximum change from the
ambient (+25°C) value to the value at either TMIN or TMAX. For
offset and gain drift, the drift is reported in ppm of full-scale
range (FSR) per degree C. For reference drift, the drift is re-
ported in ppm per degree C.
Group Delay
Number of input clocks between an impulse applied at the
device input and peak DAC output current.
Impulse Response
Response of the device to an impulse applied to the input.
Power Supply Rejection
The maximum change in the full-scale output as the supplies
are varied from nominal to minimum and maximum specified
voltages.
+3V
D
CLK4
؋
IN PLLLOCK PLL ENABLE
VCO
IN/EXT DIVIDE
PLL
CLK
IN/OUT
PLLCOM
LPF
TO HP3589A
SPECTRUM/NETWORK
ANALYZER
PLL CLOCK
MULTIPLIER
50⍀ INPUT
1.5k⍀
0.01F
MINI-CIRCUITS
T1-1T
1
؋
2
؋
14
4
؋
14
PLLVDD
IOUTA
+3V
D
4
؋
14
EDGE
DIGITAL
DATA
TRIGGERED
LATCHES
14-BIT DAC
100⍀
2
؋
2
؋
IOUTB
REFIO
14
0.1F
50⍀
20pF
50⍀
20pF
SNOOZE
SLEEP
+1.2V REFERENCE
AND CONTROL AMP
AD9774
ICOMP
FSADJ
REFLO
ACOM
AVDD REFCOMP
DCOM
DVDD
1.91k⍀
0.1F
0.1F
+3V
D
+5V
A
Figure 3. Basic AC Characterization Test Setup
–7–
REV. B
AD9774
Typical AC Characterization Curves
(AVDD = +5 V, PLLVDD = +3 V, DVDD = +3 V, IOUTFS = 20 mA, 50 ⍀ Doubly Terminated Load, Differential Output, TA = +25؇C, unless otherwise
noted. Note: PLLVDD = +5 V and DVDD = +5 V for Figures 4, 5 and 6.)
“INBAND”
10
0
90
85
80
75
70
65
60
85
80
75
70
65
60
–10
–20
–30
–40
–50
–60
–70
–80
–90
0dBFS
–6dBFS
0dBFS
–12dBFS
55
50
45
40
35
–6dBFS
–12dBFS
–18dBFS
–18dBFS
0
2
4
6
8
10
12
14
0
25.6
51.2
76.8
102.4
128.0
0
2
4
6
8
10
12
14
MHz
fOUT – MHz
fOUT – MHz
Figure 5. “Inband” SFDR vs. fOUT
@ 32 MSPS (DC to CLKIN/2)
Figure 4. Single Tone Spectral Plot
@ 32 MSPS w/fOUT = 12.8 MHz (DC to
4 × CLKIN)
Figure 6. “Out-of-Band” SFDR vs. fOUT
@ 32 MSPS (CLKIN/2 to 3 1/2 CLKIN)
“INBAND”
10
85
80
90
85
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
75
0dBFS
70
80
65
–6dBFS
–6dBFS
60
75
–12dBFS
–12dBFS
0dBFS
55
–18dBFS
70
50
–18dBFS
65
45
40
35
0
60
0
0
12.8
25.6
38.4
MHz
51.2
64.0
1
2
3
4
5
6
7
1
2
3
4
5
6
7
fOUT – MHz
fOUT – MHz
Figure 7. Single Tone Spectral Plot
@ 16 MSPS w/fOUT = 6.4 MHz (DC to
4 × CLKIN)
Figure 8. “Inband” SFDR vs. fOUT
@ 16 MSPS (DC to CLKIN/2)
Figure 9. “Out-of-Band” SFDR vs.
fOUT @ 16 MSPS (CLKIN/2 to 3 1/2
CLKIN)
10
0
90
85
–6dBFS
80
0dBFS
75
85
–10
–20
–30
–40
–50
–60
–70
–80
0dBFS
70
65
60
55
50
45
40
35
–12dBFS
–18dBFS
80
–6dBFS
75
–12dBFS
70
–18dBFS
65
–90
0
60
0
0.5
1
1.5
2
2.5
3
3.5
6.4
12.8
19.2
MHz
25.6
32.0
0
0.5
1
1.5
fOUT – MHz
2
2.5
3
3.5
fOUT – MHz
Figure 10. Single Tone Spectral Plot
OUT @ 8 MSPS w/fOUT = 3.2 MHz (DC
to 4 × CLKIN)
Figure 11. “Inband” SFDR vs. fOUT
@ 8 MSPS (DC to CLKIN/2)
Figure 12. “Out-of-Band” SFDR vs.
OUT @ 8 MSPS (CLKIN/2 to 3 1/2
CLKIN)
f
f
REV. B
–8–
AD9774
10
0
85
80
75
70
65
60
55
50
45
40
35
90
85
80
75
70
0dBFS
–10
–20
–30
–40
–50
–60
–70
–80
–90
–6dBFS
0dBFS
–12dBFS
–18dBFS
–6dBFS
–12dBFS
–18dBFS
65
60
0
1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0
MHz
0
0.2
0.3
0.4
0.5 0.6
0.7 0.8
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
fOUT – MHz
fOUT – MHz
Figure 13. Single Tone Spectral Plot
@ 2 MSPS w/fOUT = 800 kHz (DC to
4 × CLKIN)
Figure 14. “Inband” SFDR vs. fOUT
@ 2 MSPS (DC to CLKIN/2)
Figure 15. “Out-of-Band” SFDR
vs. fOUT @ 2 MSPS (CLKIN/2 to
3 1/2 CLKIN)
90
85
80
80
85
75
70
65
60
55
50
45
363kHz @ 4MSPS
727kHz @ 8MSPS
2.9MHz @ 32MSPS
75
80
DVDD = 3.3V
727kHz @ 8MSPS
1.45MHz @ 16MSPS
DVDD = 5.0V
70
75
70
363kHz @ 4MSPS
2.9MHz @ 32MSPS
65
1.45MHz @ 16MSPS
65
40
35
60
60
–18 –16 –14 –12 –10 –8 –6 –4 –2
0
10
20
30
0
–18 –16 –14 –12 –10 –8 –6 –4 –2
A
– dBFS
fCLK – MSPS
A
– dBFS
IN
IN
Figure 16. “In-Band” Single Tone
SFDR vs. AIN @ fOUT = fCLOCK/7
(DC to CLKIN/2)
Figure 17. Out-of-Band Single Tone
SFDR vs. AIN @ fOUT = fCLOCK/7
(DC to 3 1/2 CLKIN)
Figure 18. SNR vs. fCLKIN @ fOUT
2 MHz (DC to CLKIN/2)
=
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
85
80
80
2.8/3.2MHz @ 8MSPS
11.2/12.8MHz @ 32MSPS
75
1.4/1.6MHz @ 4MSPS
75
70
70
2.8/3.2MHz @ 8MSPS
65
5.6/6.4MHz @ 16MSPS
65
60
5.6/6.4MHz @ 16MSPS
55
1.4/1.6MHz @ 4MSPS
60
11.2/12.8MHz @ 32MSPS
50
45
55
50
40
35
0
25.6
51.2
76.8
102.4 128.0
0
0
–18 –16 –14 –12 –10 –8 –6 –4 –2
–18 –16 –14 –12 –10 –8 –6 –4 –2
– dBFS
A
– dBFS
A
OUT
OUT
Figure 19. “In-Band” Two Tone
SFDR vs. AOUT @ fOUT = fCLOCK/2.7
(DC to CLKIN/2)
Figure 20. “Out-of-Band” Two Tone
SFDR vs. AOUT @ fOUT = fCLOCK/2.7
(DC to 3 1/2 CLKIN)
Figure 21. Multitone Spectral Plot
@ 32 MSPS (DC to 4 × CLKIN)
REV. B
–9–
AD9774
FUNCTIONAL DESCRIPTION
coefficients for each of the filter stages. The interpolation filters
essentially multiply the input data rate to the DAC by a factor of
four relative to its original input data rate while simultaneously
reducing the magnitude of the images associated with the origi-
nal input data rate.
Figure 22 shows a simplified block diagram of the AD9774. The
AD9774 is a complete, 4× oversampling, 14-bit DAC that in-
cludes two cascaded 2× interpolation filters, a phase-locked loop
(PLL) clock multiplier, and a 1.20 Volt bandgap voltage refer-
ence. The 14-bit DAC provides two complementary current
outputs whose full-scale current is determined by an external
resistor. Input data that is latched into the edge-triggered input
latches is first interpolated by a factor of four by the interpolation
filters before updating the 14-bit DAC. A PLL clock multiplier
produces the necessary internally synchronized 1×, 2× and 4×
clocks from an external reference. The AD9774 can support
input data rates as high as 32 MSPS, corresponding to a DAC
update rate of 128 MSPS.
The benefits of an interpolation filter are clearly seen in Figure
23, which shows an example of the frequency and time domain
representation of a discrete time sine wave signal before and
after it is applied to a digital interpolation filter. Images of the
sine wave signal appear around multiples of the DAC’s input
data rate as predicted by sampling theory. These undesirable
images will also appear at the output of a reconstruction DAC,
although modified by the DAC’s sin(x)/(x) roll-off response.
In many bandlimited applications, these images must be sup-
pressed by an analog filter following the DAC. The complexity
of this analog filter is typically determined by the proximity of
the desired fundamental to the first image and the required
amount of image suppression. Adding to the complexity of this
analog filter may be the requirement of compensating for the
DAC’s sin(x)/x response.
The analog and digital sections of the AD9774 have separate
power supply inputs (i.e., AVDD and DVDD) that can operate
over a 2.7 V to 5.5 V range. A separate supply input (i.e.,
PLLVDD) having a similar operating range is also provided for
the PLL clock multiplier. To maintain optimum noise and dis-
tortion performance, PLLVDD should be maintained at the
same voltage level as DVDD.
Referring to Figure 23, the “new” first image associated with the
DAC’s higher data rate after interpolation is “pushed” out fur-
ther relative to the input signal. The “old” first image associated
with the lower DAC data rate before interpolation is suppressed
by the digital filter. As a result, the transition band for the ana-
log reconstruction filter is increased, thus reducing the complex-
ity of the analog filter. Furthermore, the sin(x)/x roll-off over the
effective passband (i.e., dc to fCLOCK/2) is significantly reduced.
PLL
DIVIDE
VCO
IN/EXT
PLL
PLLLOCK ENABLE
CLK4
؋
IN PLLCOM
LPF
AD9774
PLL CLOCK
MULTIPLIER
CLK IN/OUT
1
؋
2
؋
4
؋
PLLVDD
4
؋
14
14
14
14
DATA
INPUTS
(DB13–DB0)
IOUTA
IOUTB
EDGE
TRIGGERED
LATCHES
The AD9774 includes a PLL clock multiplier that produces the
necessary internally synchronized 1×, 2× and 4× clocks for the
edge triggered latches, interpolation filters and DACs. The
PLL clock multiplier typically accepts an input data clock,
CLK IN/OUT, as its reference source. Alternatively, it can also
be configured using an external 4× clock via CLK4×IN. The
PLLDIVIDE, VCO IN/EXT, PLLENABLE, and PLLLOCK
are control inputs/outputs used in the PLL clock generator.
Refer to the PLL CLOCK MULTIPLIER OPERATION sec-
tion for a detailed discussion on its operation.
14-BIT
DAC
2
؋
2
؋
SNOOZE
SLEEP
REFIO
FSADJ
+1.2V REFERENCE
AND CONTROL AMP
ICOMP ACOM AVDD REFCOMP REFLO
DVDD
DCOM
Figure 22. Functional Block Diagram
Preceding the 14-bit DAC are two cascaded 2× digital interpola-
tion filter stages based on a 55- and 23-tap halfband symmetric
FIR topology. Edge triggered latches are used to latch the input
data on the rising edge of CLK IN/OUT. The composite fre-
quency and impulse response of both filters are shown in Fig-
ures 2a and 2b. Table I and Table II list the idealized filter
The digital section of the AD9774 also includes several other
control inputs and outputs. The SLEEP and SNOOZE inputs
provide different power-saving modes as discussed in the
SLEEP and SNOOZE section.
1
4fCLOCK
TIME DOMAIN
1
fCLOCK
ST
FUNDAMENTAL
1
IMAGE
FUNDAMENTAL
DIGITAL
"NEW"
1ST IMAGE
"SINX"
X
DACs
FILTER
FREQUENCY DOMAIN
SUPPRESSED
4fCLOCK
2fCLOCK 4fCLOCK
2fCLOCK
2fCLOCK 4fCLOCK
"OLD"
ST
1
IMAGE
4x INTERPOLATION FILTER
4x
INPUT DATA LATCH
DAC
fCLOCK
4
؋
fCLOCK Figure 23. Time and Frequency Domain Example of Digital Interpolation Filter
–10–
REV. B
AD9774
PLL CLOCK MULTIPLIER OPERATION
There are two cases in which a user may consider or be required
to disable the internal PLL Clock Multiplier and supply the
AD9774 with an external 4× system clock. Applications already
containing a system clock operating at four (i.e., 4×) the input
data rate may consider using it as the master clock source. Ap-
plications with input data rates less than 5.5 MSPS must use a
master 4× clock.
The Phase Lock Loop (PLL) Clock Multiplier is intrinsic to the
operation of the AD9774 in that it produces the necessary inter-
nally synchronized 1×, 2× and 4× clocks for the edge triggered
latches, interpolation filters and DACs. Figure 24 shows a func-
tional block diagram of the PLL Clock Multiplier, which con-
sists of a phase detector, a charge pump, a voltage controlled
oscillator (VCO), a divide-by-N circuit and some control inputs/
outputs. It produces the required internal clocks for the AD9774
by using one of two possible externally applied reference clock
sources applied to either CLKIN or CLK4×IN. PLLENABLE
and VCO IN/EXT are active HIGH control inputs used to
enable the charge pump and VCO respectively.
In any of these cases, the clock source is applied to CLK4×IN
and the PLL is partially disabled by typing PLLENABLE and
VCO IN/EXT to PLLCOM as shown in Figure 25. LPF may
remain open since this portion of the PLL circuitry is disabled.
The divide-by-N circuit still remains enabled providing a 1× or
2× internal clock at CLOCK IN/OUT depending on the state of
PLLDIVIDE. Since the digital input data is latched into the
AD9774 on the rising edge of the 1× clock, PLLDIVIDE should
be tied to PLLCOM such that the 1× clock appears as an output
at CLOCK IN/OUT. The input data should be stable 5 ns (i.e.,
data set-up) before the rising edge of the 1× clock appearing at
CLOCK IN/OUT and remain stable for 1 ns after the rising
edge (i.e., data hold) to ensure proper latching. Note, the rising
edge of the 1× clock occurs approximately 9 ns to 15 ns relative
to the falling edge of the CLK4× input. If a data timing issue
exists between the AD9774 and its external driver device, the
CLK4× input can be inverted via an external gate to ensure
proper set-up and hold time.
To maintain optimum noise and distortion performance,
PLLVDD and DVDD should be set to similar voltage levels. If
a separate supply cannot be provided for PLLVDD, PLLVDD
can be tied to DVDD using an LC filter network similar to that
shown in Figure 41.
Many applications will select a reference clock operating at the
data input rate as shown in Figure 24. In this case, the external
clock source is applied to CLKIN and the PLL Clock Multiplier
is fully enabled by tying PLLENABLE and VCO IN/EXT to
PLLVDD. Note, CLKIN must adhere to the timing require-
ments shown in Figure 1. A 1.5 kΩ resistor and 0.01 µF ceramic
capacitor connected in series from LPF to PLLVDD are re-
quired to optimize the phase noise vs. settling/acquisition time
characteristics of the PLL. PLLLOCK is a control output, ac-
tive HIGH, which may be monitored upon system power-up to
indicate that the PLL is successfully “locked” to CLKIN. Note,
applications employing multiple AD9774 devices will benefit
from the PLL Clock Multiplier’s ability to ensure precise simul-
taneous updating/phase synchronization of these devices when
driven by the same input clock source.
PLLLOCK
CLK
PLL
DIVIDE
PLL
ENABLE
IN/OUT
PHASE
DETECTOR
CHARGE
PUMP
LPF
AD9774
PLLDIVIDE is used to preset the “lock-in” range of the PLL. It
should be tied to PLLCOM if CLKIN is greater than 10 MHz
and to PLLVDD if CLKIN is between 5.5 MHz and 10 MHz.
For operation below 5.5 MHz (i.e., input data rates less than
5.5 MSPS), the internal charge pump and VCO should be
disabled by tying PLLENABLE and VCO IN/EXT LOW. In
this case, the user MUST supply a system clock operating at 4×
the input data rate as discussed below.
PLL
VDD
،8
+2.7 TO +5.5 V
D
،4
VCO
DIVIDE-
BY-N
PLL
COM
،2
،1
VCO
IN/EXT
CLK
4
؋
IN DCOM
DVDD
+2.7 TO +5.5 V
D
Figure 25. Clock Divider with PLL Disabled
CONNECT TO
PLLCOM
CONNECT TO
PLLVDD
PLLLOCK
CLK
IN/OUT
DAC OPERATION
The 14-bit DAC along with the 1.2 V reference and reference
PLL
DIVIDE
PLL
ENABLE
control amplifier is shown in Figure 26. The DAC consists of a
large PMOS current source array capable of providing up to
20 mA of full-scale current, IOUTFS. The array is divided into 31
equal currents which make up the five most significant bits
(MSBs). The next four bits or middle bits consist of 15 equal
current sources whose values are 1/16th of an MSB current
source. The remaining LSBs are binary weighted fractions of the
middle-bits current sources. All of these current sources are
switched to one or the other of two output nodes (i.e., IOUTA
or IOUTB) via PMOS differential current switches. Implement-
ing the middle and lower bits with current sources, instead of an
R-2R ladder, enhances its dynamic performance for multitone
or low amplitude signals and helps maintain the DAC’s high
output impedance (i.e., > 100 kΩ).
LPF
PHASE
DETECTOR
CHARGE
PUMP
1.5k⍀
AD9774
0.01F
PLL
VDD
،8
،4
VCO
DIVIDE-
BY-N
+2.7 TO
+5.5 V
PLL
،2
،1
COM
D
CLK
4
؋
IN VCO
IN/EXT
DCOM
DVDD
+2.7 TO +5.5 V
D
Figure 24. Clock Multiplier with PLL Enabled
REV. B
–11–
AD9774
+2.7 TO +5.5V
Substituting the values of IOUTA, IOUTB and IREF; VDIFF can
be expressed as:
A
0.1F
REFLO
REFCOMP AVDD ACOM
50pF
V
V
DIFF = {(2 DAC CODE – 16383)/16384} ×
DIFF = {(32 RLOAD/RSET) × VREFIO
(8)
1.20V REF
ICOMP 0.1F
CURRENT
SOURCE
ARRAY
REFIO
These last two equations highlight some of the advantages of
operating the AD9774 differentially. First, the differential
FS ADJ
1.91k⍀
0.1F
IOUTA
IOUTB
operation will help cancel common-mode error sources associ-
ated with IOUTA and IOUTB such as noise, distortion and dc
offsets. Second, the differential code-dependent current and
subsequent voltage, VDIFF, is twice the value of the single-ended
voltage output (i.e., VOUTA or VOUTB), thus providing twice the
signal power to the load.
LSB
SEGMENTED
SWITCHES
SWITCHES
AD9774
Figure 26. Block Diagram of Internal DAC, 1.2 V Reference,
and Reference Control Circuits
Note that the gain drift temperature performance for a single-
ended (VOUTA and VOUTB) or differential output (VDIFF) of
the AD9774 can be enhanced by selecting temperature tracking
resistors for RLOAD and RSET due to their ratiometric relation-
ship as shown in Equation 8.
The full-scale output current is regulated by the reference con-
trol amplifier and can be set from 2 mA to 20 mA via an exter-
nal resistor, RSET. The external resistor, in combination with
both the reference control amplifier and voltage reference,
REFIO, sets the reference current, IREF, which is mirrored over
to the segmented current sources with the proper scaling factor.
The full-scale current, IOUTFS, is exactly thirty-two times the
REFERENCE OPERATION
The AD9774 contains an internal 1.20 V bandgap reference
that can be easily disabled and overridden by an external
reference. REFIO serves as either an input or output, depending
on whether the internal or external reference is selected. If
REFLO is tied to ACOM, as shown in Figure 27, the internal
reference is activated, and REFIO provides a 1.20 V output. In
this case, the internal reference must be compensated externally
with a ceramic chip capacitor of 0.1 µF or greater from REFIO
to REFLO. If any additional loading is required, REFIO should
be buffered with an external amplifier having an input bias cur-
rent less than 100 nA.
value of IREF
.
DAC TRANSFER FUNCTION
The AD9774 provides complementary current outputs, IOUTA
and IOUTB. IOUTA will provide a near full-scale current out-
put, IOUTFS, when all bits are high (i.e., DAC CODE = 16383)
while IOUTB, the complementary output, provides no current.
The current output appearing at IOUTA and IOUTB is a func-
tion of both the input code and IOUTFS and can be expressed as:
IOUTA = (DAC CODE/16384) × IOUTFS
(1)
(2)
+2.7 TO +5.5V
A
IOUTB = (16383 – DAC CODE)/16384 × IOUTFS
OPTIONAL
EXTERNAL
REF BUFFER
where DAC CODE = 0 to 16383 (i.e., Decimal Representation).
0.1F
REFLO
+1.2V REF
REFCOMP
50pF
AVDD
As previously mentioned, IOUTFS is a function of the reference
current IREF, which is nominally set by a reference voltage
V
REFIO and external resistor RSET. It can be expressed as:
REFIO
FSADJ
CURRENT
SOURCE
ARRAY
ADDITIONAL
LOAD
I
OUTFS = 32 × IREF
(3)
(4)
0.1F
2k⍀
where IREF = VREFIO/RSET
AD9774
The two current outputs will typically drive a resistive load
directly or via a transformer. If dc coupling is required, IOUTA
and IOUTB should be directly connected to matching resistive
loads, RLOAD, that are tied to analog common, ACOM. Note
that RLOAD may represent the equivalent load resistance seen by
IOUTA or IOUTB as would be the case in a doubly terminated
50 Ω or 75 Ω cable. The single-ended voltage output appearing
at the IOUTA and IOUTB nodes is simply:
Figure 27. Internal Reference Configuration
The internal reference can be disabled by connecting REFLO to
AVDD. In this case, an external reference may then be applied
to REFIO as shown in Figure 28. The external reference may
provide either a fixed reference voltage to enhance accuracy and
drift performance or a varying reference voltage for gain control.
Note that the 0.1 µF compensation capacitor is not required
since the internal reference is disabled, and the high input im-
pedance (i.e., 1 MΩ) of REFIO minimizes any loading of the
external reference.
V
OUTA = IOUTA × RLOAD
OUTB = IOUTB × RLOAD
(5)
(6)
V
Note that the full-scale value of VOUTA and VOUTB should not
exceed the specified output compliance range to maintain speci-
fied distortion and linearity performance.
The differential voltage, VDIFF, appearing across IOUTA and
IOUTB is:
V
DIFF = (IOUTA – IOUTB) × RLOAD
(7)
–12–
REV. B
AD9774
+2.7 TO +5.5V
A
varied by an external voltage, VGC, applied to RSET via an ampli-
fier. An example of this method is shown in Figure 29 in which
the internal reference is used to set the common-mode voltage
of the control amplifier to 1.20 V. The external voltage, VGC, is
referenced to ACOM and should not exceed 1.2 V. The value of
0.1F
REFCOMP
REFLO
+1.2V REF
AVDD
AVDD
50pF
R
SET is such that IREFMAX and IREFMIN do not exceed 62.5 µA
V
REFIO
REFIO
and 625 µA, respectively. The associated equations in Figure 29
EXTERNAL
REF
CURRENT
SOURCE
ARRAY
can be used to determine the value of RSET
.
FS ADJ
R
I
V
=
SET
REF
+2.7 TO +5.5V
A
/R
REFERENCE
CONTROL
AMPLIFIER
REFIO SET
AD9774
0.1F
REFLO
AVDD
REFCOMP
50pF
Figure 28. External Reference Configuration
+1.2V REF
REFIO
FSADJ
CURRENT
SOURCE
ARRAY
REFERENCE CONTROL AMPLIFIER
The AD9774 also contains an internal control amplifier that is
used to regulate the DAC’s full-scale output current, IOUTFS
1F
R
SET
I
AD9774
REF
.
The control amplifier is configured as a V-I converter, as shown
in Figure 28, such that its current output, IREF, is determined by
the ratio of the VREFIO and an external resistor, RSET, as stated
in Equation 4. IREF is copied over to the segmented current
sources with the proper scaling factor to set IOUTFS as stated in
Equation 3.
I
= (1.2–V )/R
GC SET
REF
V
GC
WITH V Ͻ V
AND 62.5 A Յ I
Յ 625A
REF
GC
REFIO
Figure 29. Dual Supply Gain Control Circuit
ANALOG OUTPUTS
The AD9774 produces two complementary current outputs,
IOUTA and IOUTB, which may be configured for single-end or
differential operation. IOUTA and IOUTB can be converted
into complementary single-ended voltage outputs, VOUTA and
VOUTB, via a load resistor, RLOAD, as described in the DAC
Transfer Function section by Equations 5 through 8. The
The control amplifier allows a wide (10:1) adjustment span of
I
OUTFS over a 2 mA to 20 mA range by setting IREF between
62.5 µA and 625 µA. The wide adjustment span of IOUTFS
provides several application benefits. The first benefit relates
directly to the power dissipation of the AD9774, which is pro-
portional to IOUTFS (refer to the Power Dissipation section). The
second benefit relates to the 20 dB adjustment, which is useful
for system gain control purposes.
differential voltage, VDIFF, existing between VOUTA and VOUTB
can also be converted to a single-ended voltage via a transformer
or differential amplifier configuration.
,
There are two methods by which IREF can be varied for a fixed
Figure 31 shows the equivalent analog output circuit of the
AD9774 consisting of a parallel combination of PMOS differen-
tial current switches associated with each segmented current
source. The output impedance of IOUTA and IOUTB is deter-
mined by the equivalent parallel combination of the PMOS
switches and is typically 100 kΩ in parallel with 5 pF. Due to
the nature of a PMOS device, the output impedance is also
RSET. The first method is suitable for a single-supply system in
which the internal reference is disabled, and the common-mode
voltage of REFIO is varied over its compliance range of 1.25 V
to 0.10 V. REFIO can be driven by a single-supply amplifier or
DAC, thus allowing IREF to be varied for a fixed RSET. Since the
input impedance of REFIO is approximately 1 MΩ, a simple,
low cost R-2R ladder DAC configured in the voltage mode
topology may be used to control the gain. This circuit is shown
in Figure 30 using the AD7524 and an external 1.2 V reference,
the AD1580.
slightly dependent on the output voltage (i.e., VOUTA and VOUTB
and, to a lesser extent, the analog supply voltage, AVDD, and
full-scale current, IOUTFS. Although the output impedance’s
)
signal dependency can be a source of dc nonlinearity and ac linear-
ity (i.e., distortion), its effects can be limited if certain precau-
tions are noted.
The second method may be used in a dual-supply system in
which the common-mode voltage of REFIO is fixed, and IREF is
+2.7 TO +5.5V
A
AVDD
0.1F
REFLO
+1.2V REF
REFCOMP
50pF
AVDD
R
V
FB
DD
V
1.2V
OUT1
OUT2
0.1V TO 1.2V
REFIO
FSADJ
AD7524
CURRENT
SOURCE
ARRAY
REF
AD1580
AGND
R
I
=
SET
AD9774
REF
V
/R
REF SET
DB7–DB0
Figure 30. Single Supply Gain Control Circuit
REV. B
–13–
AD9774
The distortion and noise performance of the AD9774 is also
slightly dependent on the analog and digital supply as well as the
full-scale current setting, IOUTFS. Operating the analog supply at
5.0 V ensures maximum headroom for its internal PMOS current
sources and differential switches leading to improved distortion
performance. Although IOUTFS can be set between 2 mA and
20 mA, selecting an IOUTFS of 20 mA will provide the best dis-
tortion and noise performance. The noise performance of the
AD9774 is affected by the digital supply (DVDD), output fre-
quency, and increases with increasing clock rate. Operating the
AD9774 with low voltage logic levels between 3 V and 3.3 V
will slightly reduce the amount of on-chip digital noise.
AD9774
AVDD
IOUTA
IOUTB
R
R
LOAD
LOAD
In summary, the AD9774 achieves the optimum distortion and
noise performance under the following conditions:
Figure 31. Equivalent Analog Output Circuit
(1) Differential Operation.
IOUTA and IOUTB also have a negative and positive voltage
compliance range. The negative output compliance range of
–1.0 V is set by the breakdown limits of the CMOS process.
Operation beyond this maximum limit may result in a break-
down of the output stage and affect the reliability of the AD9774.
The positive output compliance range is slightly dependent on
the full-scale output current, IOUTFS. It degrades slightly from its
(2) Positive voltage swing at IOUTA and IOUTB limited to
+0.5 V.
(3) IOUTFS set to 20 mA.
(4) Analog Supply (AVDD) set at 5.0 V.
(5) Digital Supply (DVDD) and Phase Lock Loop Supply
(PLLVDD) set at 3.0 V to 3.3 V with appropriate logic
levels.
nominal 1.25 V for an IOUTFS = 20 mA to 1.00 V for an IOUTFS
2 mA. Operation beyond the positive compliance range will
=
induce clipping of the output signal, which severely degrades
the AD9774’s linearity and distortion performance.
Note that the ac performance of the AD9774 is characterized
under the above-mentioned operating conditions.
For applications requiring the optimum dc linearity, IOUTA
and/or IOUTB should be maintained at a virtual ground via an
I-V op amp configuration. Maintaining IOUTA and/or IOUTB
at a virtual ground keeps the output impedance of the AD9774
fixed, significantly reducing its effect on linearity. However, it
does not necessarily lead to the optimum distortion perfor-
mance due to limitations of the I-V op amp. Note that the
INL/DNL specifications for the AD9774 are measured in this
manner using IOUTA. In addition, these dc linearity specifi-
cations remain virtually unaffected over the specified power
supply range of 2.7 V to 5.5 V.
DIGITAL INPUTS/OUTPUTS
The digital input of the AD9774 consists of 14 data input pins
and a clock input pin, and several control input pins. Since
some of the internal logic is operated from DVDD and PLLVDD,
they must be set to the same or similar levels to ensure proper
compatibility with any external logic/drivers. The two digital
outputs of the AD9774, PLL LOCK and CLK OUT originate
from the internal PLL circuitry and thus its output logic levels
will be set by PLLVDD.
The 14-bit parallel data inputs follow standard positive binary
coding where DB13 is the most significant bit (MSB), and DB0
is the least significant bit (LSB). IOUTA produces a full-scale
output current when all data bits are at Logic 1. IOUTB pro-
duces a complementary output with the full-scale current split
between the two outputs as a function of the input code.
Operating the AD9774 with reduced voltage output swings at
IOUTA and IOUTB in a differential or single-ended output
configuration reduces the signal dependency of its output im-
pedance thus enhancing distortion performance. Although the
voltage compliance range of IOUTA and IOUTB extends from
–1.0 V to +1.25 V, optimum distortion performance is achieved
when the maximum full-scale signal at IOUTA and IOUTB
does not exceed approximately 0.5 V. A properly selected trans-
former with a grounded center-tap will allow the AD9774 to
provide the required power and voltage levels to different loads
while maintaining reduced voltage swings at IOUTA and
IOUTB. DC-coupled applications requiring a differential or
single-ended output configuration should size RLOAD accord-
ingly. Refer to Applying the AD9774 section for examples of
various output configurations.
The digital interface is implemented using an edge-triggered
master slave latch and is designed to support a clock and input
data rate as high as 32 MSPS. The clock can be operated at any
duty cycle that meets the specified latch pulsewidth as shown in
Figure 1. The setup and hold times can also be varied within the
clock cycle as long as the specified minimum times are met.
The digital inputs are CMOS-compatible with logic thresholds,
VTHRESHOLD, set to approximately half the digital positive supply
(i.e., DVDD or PLLVDD) or
VTHRESHOLD = DVDD/2 (±20%)
The most significant improvement in the AD9774’s distortion
and noise performance is realized using a differential output
configuration. The common-mode error sources of both IOUTA
and IOUTB can be substantially reduced by the common-mode
rejection of a transformer or differential amplifier. These
common-mode error sources include even-order distortion
products and noise. The enhancement in distortion performance
becomes more significant as the reconstructed waveform’s
frequency content increases and/or its amplitude decreases.
The internal digital circuitry of the AD9774 is capable of operating
over a digital supply range of 2.7 V to 5.5 V. As a result, the
digital inputs can also accommodate TTL levels when DVDD is
set to accommodate the maximum high level voltage of the TTL
drivers VOH(MAX). A DVDD of 3 V to 3.3 V will typically ensure
proper compatibility with most TTL logic families. Figure 32
shows the equivalent digital input circuit for the data and clock
inputs.
–14–
REV. B
AD9774
DVDD
DVDD = 3 V, respectively. Note, how IDVDD is reduced by more
than a factor of 2 when DVDD is reduced from 5 V to 3 V.
DIGITAL
INPUT
30
25
20
15
10
5
Figure 32. Equivalent Digital Input
Since the AD9774 is capable of being updated up to 32 MSPS,
the quality of the clock and data input signals are important in
achieving the optimum performance. Operating the AD9774
with reduced logic swings and a corresponding digital supply
(DVDD) will result in the lowest data feedthrough and on-chip
digital noise. The drivers of the digital data interface circuitry
should be specified to meet the minimum setup and hold times
of the AD9774 as well as its required min/max input logic level
thresholds.
0
2
4
6
8
10
12
14
16
18
20
I
– mA
OUTFS
Figure 33. IAVDD vs. IOUTFS
Digital signal paths should be kept short and run lengths matched
to avoid propagation delay mismatch. The insertion of a low
value resistor network (i.e., 20 Ω to 100 Ω) between the AD9774
digital inputs and driver outputs may be helpful in reducing any
overshooting and ringing at the digital inputs that contribute to
data feedthrough.
200
180
160
140
32MSPS
The external clock driver circuitry should provide the AD9774
with a low jitter clock input meeting the min/max logic levels
while providing fast edges. Fast clock edges will help minimize
any jitter that will manifest itself as phase noise on a recon-
structed waveform. Thus, the clock input should be driven by
the fastest logic family suitable for the application.
120
100
80
16MSPS
60
40
8MSPS
4MSPS
20
0
SLEEP AND SNOOZE MODE OPERATION
The AD9774 has a SLEEP function that turns off the output
current and reduces the supply current to less than 5 mA over
the specified supply range of 2.7 V to 5.5 V and temperature
range. This mode can be activated by applying a logic level “1”
to the SLEEP pin. The AD9774 takes less than 0.1 µs to power
down and approximately 6.4 µs to power back up.
0.01
0.10
1.0
RATIO – fOUT/fCLOCK
Figure 34. IDVDD vs. Ratio @ DVDD = 5 V
100
The SNOOZE mode should be considered as an alternative
power-savings option if the power-up characteristics of the
SLEEP mode are unsuitable. This mode, which is also activated
by applying a logic level “1” to the SNOOZE pin, disables the
AD9774’s digital filters only, resulting in significant power
savings. Both the SLEEP and SNOOZE pins should be tied to
DCOM if power savings is not required.
32MSPS
90
80
70
60
50
40
30
20
10
16MSPS
POWER DISSIPATION
The power dissipation, PD, of the AD9774 is dependent on
several factors, including: (1) AVDD, PLLVDD, and DVDD,
the power supply voltages; (2) IOUTFS, the full-scale current
output; (3) fCLOCK, the update rate; and (4) the reconstructed
digital input waveform. The power dissipation is directly pro-
portional to the analog supply current, IAVDD, and the digital
supply current, IDVDD. IAVDD is directly proportional to IOUTFS,
8MSPS
4MSPS
0
0.01
0.10
RATIO – fOUT
1.0
/
fCLOCK
Figure 35. IDVDD vs. Ratio @ DVDD = 3 V
For those applications requiring the AD9774 to operate under the
following conditions: (1) AVDD, PLLVDD and DVDD = +5 V;
(2) fCLOCK > 25 MSPS; and (3) ambient temperatures > 70°C;
proper thermal management via a heatsink or thermal epoxy is
recommended.
as shown in Figure 33, and is insensitive to fCLOCK
.
Conversely, IDVDD is dependent on both the digital input wave-
form, fCLOCK, and digital supply DVDD. Figures 34 and 35
show IDVDD as a function of full-scale sine wave output ratios
(fOUT/fCLOCK) for various update rates with DVDD = 5 V and
REV. B
–15–
AD9774
DIFFERENTIAL USING AN OP AMP
APPLYING THE AD9774
An op amp can also be used to perform a differential-to-single-
ended conversion as shown in Figure 37. The AD9774 is
configured with two equal load resistors, RLOAD, of 25 Ω. The
differential voltage developed across IOUTA and IOUTB is
converted to a single-ended signal via the differential op amp
configuration. An optional capacitor can be installed across
IOUTA and IOUTB, forming a real pole in a low-pass filter.
The addition of this capacitor also enhances the op amp’s distor-
tion performance by preventing the DAC’s high slewing output
from overloading the op amp’s input.
OUTPUT CONFIGURATIONS
The following sections illustrate some typical output configura-
tions for the AD9774. Unless otherwise noted, it is assumed
that IOUTFS is set to a nominal 20 mA. For applications requir-
ing the optimum dynamic performance, a differential output
configuration is suggested. A differential output configuration
may consist of either an RF transformer or a differential op amp
configuration. The transformer configuration provides the opti-
mum high frequency performance and is recommended for any
application allowing for ac coupling. The differential op amp
configuration is suitable for applications requiring dc coupling, a
bipolar output, signal gain and/or level shifting.
500⍀
AD9774
A single-ended output is suitable for applications requiring a
unipolar voltage output. A positive unipolar output voltage will
result if IOUTA and/or IOUTB is connected to an approximately
sized load resistor, RLOAD, referred to ACOM. This configura-
tion may be more suitable for a single-supply system requiring a
dc-coupled, ground referred output voltage. Alternatively, an
amplifier could be configured as an I-V converter, thus convert-
ing IOUTA or IOUTB into a negative unipolar voltage. This
configuration provides the best dc linearity since IOUTA or
IOUTB is maintained at a virtual ground.
225⍀
22
21
IOUTA
AD8055
225⍀
IOUTB
C
OPT
500⍀
25⍀
25⍀
Figure 37. DC Differential Coupling Using an Op Amp
The common-mode rejection of this configuration is typically
determined by the resistor matching. In this circuit, the differ-
ential op amp circuit using the AD8055 is configured to provide
some additional signal gain. The op amp must operate from a
dual supply since its output is approximately ±1.0 V. A high
speed amplifier capable of preserving the differential perform-
ance of the AD9774 while meeting other system level objectives
(i.e., cost, power) should be selected. The op amps differential
gain, its gain setting resistor values and full-scale output swing
capabilities should all be considered when optimizing this circuit.
DIFFERENTIAL COUPLING USING A TRANSFORMER
An RF transformer can be used to perform a differential-to-
single-ended signal conversion as shown in Figure 36. A
differentially coupled transformer output provides the optimum
distortion performance for output signals whose spectral content
lies within the transformer’s passband. An RF transformer such
as the Mini-Circuits T1-1T provides excellent rejection of
common-mode distortion (i.e., even-order harmonics) and noise
over a wide frequency range. It also provides electrical isolation
and the ability to deliver twice the power to the load. Trans-
formers with different impedance ratios may also be used for
impedance matching purposes. Note that the transformer
provides ac coupling only.
The differential circuit shown in Figure 38 provides the neces-
sary level-shifting required in a single supply system. In this case,
AVDD, which is the positive analog supply for both the AD9774
and the op amp, is also used to level-shift the differential output
of the AD9774 to midsupply (i.e., AVDD/2). The AD8041 is a
suitable op amp for this application.
MINI-CIRCUITS
T1-1T
22
IOUTA
50
R
AD9774
LOAD
AD9774
22
22
IOUTA
21
IOUTB
AD8041
22
OPTIONAL R
DIFF
21
IOUTB
C
OPT
1
AVDD
Figure 36. Differential Output Using a Transformer
1
2
2
The center tap on the primary side of the transformer must be
connected to ACOM to provide the necessary dc current path
for both IOUTA and IOUTB. The complementary voltages
Figure 38. Single-Supply DC Differential Coupled Circuit
appearing at IOUTA and IOUTB (i.e., VOUTA and VOUTB
)
swing symmetrically around ACOM and should be maintained
with the specified output compliance range of the AD9774. A
differential resistor, RDIFF, may be inserted in applications in
which the output of the transformer is connected to the load,
SINGLE-ENDED UNBUFFERED VOLTAGE OUTPUT
Figure 39 shows the AD9774 configured to provide a unipolar
output range of approximately 0 V to +0.5 V for a doubly termi-
nated 50 Ω cable since the nominal full-scale current, IOUTFS, of
20 mA flows through the equivalent RLOAD of 25 Ω. In this case,
RLOAD represents the equivalent load resistance seen by IOUTA.
The unused output (IOUTB) can be connected to ACOM di-
rectly. Different values of IOUTFS and RLOAD can be selected as
RLOAD, via a passive reconstruction filter or cable. RDIFF is deter-
mined by the transformer’s impedance ratio and provides the
proper source termination that results in a low VSWR. Note that
approximately half the signal power will be dissipated across RDIFF
.
–16–
REV. B
AD9774
to ACOM, the analog common, as close to the chip as physi-
cally possible. Similarly, DVDD, the digital supply, should be
decoupled to DCOM and PLLVDD, the Phase Lock Loop
Supply, should be decoupled to PLLCOM.
long as the positive compliance range is adhered to. One addi-
tional consideration in this mode is the integral nonlinearity
(INL) as discussed in the Analog Output section of this data
sheet. For optimum INL performance, the single-ended, buff-
ered voltage output configuration is suggested.
For those applications requiring a single +5 V or +3 V supply
for both the analog, digital supply and Phase Lock Loop supply,
a clean AVDD and/or PLLVDD may be generated using the
circuit shown in Figure 41. The circuit consists of a differential
LC filter with separate power supply and return lines. Lower
noise can be attained using low ESR type electrolytic and tanta-
lum capacitors.
AD9774
I
= 20mA
OUTFS
V
= 0 TO +0.5V
OUTA
22
21
IOUTA
50⍀
50⍀
IOUTB
FERRITE
BEADS
Figure 39. 0 V to +0.5 V Unbuffered Voltage Output
TTL/CMOS
LOGIC
CIRCUITS
AVDD
ACOM
10-22F
TANT.
0.1F
CER.
100F
ELECT.
SINGLE-ENDED BUFFERED VOLTAGE OUTPUT
CONFIGURATION
Figure 40 shows a buffered single-ended output configuration in
which the op amp U1 performs an I-V conversion on the AD9774
output current. U1 maintains IOUTA (or IOUTB) at a virtual
ground, thus minimizing the nonlinear output impedance effect
on the DAC’s INL performance as discussed in the Analog
Output section. Although this single-ended configuration typi-
cally provides the best dc linearity performance, its ac distortion
performance at higher DAC update rates may be limited by
U1’s slewing capabilities. U1 provides a negative unipolar output
voltage and its full-scale output voltage is simply the product of
RFB and IOUTFS. The full-scale output should be set within U1’s
+5V OR +3V
POWER SUPPLY
Figure 41. Differential LC Filter for Single +5 V or +3 V
Applications
Maintaining low noise on power supplies and ground is critical
to obtain optimum results from the AD9774. If properly
implemented, ground planes can perform a host of functions on
high speed circuit boards: bypassing, shielding current trans-
port, etc. In mixed signal design, the analog and digital portions
of the board should be distinct from each other, with the analog
ground plane confined to the areas covering the analog signal
traces, and the digital ground plane confined to areas covering
the digital interconnects.
voltage output swing capabilities by scaling IOUTFS and/or RFB
.
An improvement in ac distortion performance may result with a
reduced IOUTFS since the signal current U1 will be required to
sink will be subsequently reduced.
All analog ground pins of the DAC, reference and other analog
components should be tied directly to the analog ground plane.
The two ground planes should be connected by a path 1/8 to
1/4 inch wide underneath or within 1/2 inch of the DAC to
maintain optimum performance. Care should be taken to ensure
that the ground plane is uninterrupted over crucial signal paths.
On the digital side, this includes the digital input lines running
to the DAC as well as any clock signals. On the analog side, this
includes the DAC output signal, reference signal and the supply
feeders.
C
OPT
R
FB
200⍀
I
= 10mA
OUTFS
AD9774
22
21
IOUTA
U1
V
= I
؋
R OUT
OUTFS FB
IOUTB
200⍀
The use of wide runs or planes in the routing of power lines is
also recommended. This serves the dual role of providing a low
series impedance power supply to the part, as well as providing
some “free” capacitive decoupling to the appropriate ground
plane. It is essential that care be taken in the layout of signal and
power ground interconnects to avoid inducing extraneous volt-
age drops in the signal ground paths. It is recommended that all
connections be short, direct and as physically close to the pack-
age as possible in order to minimize the sharing of conduction
paths between different currents. When runs exceed an inch in
length, strip line techniques with proper termination resistors
should be considered. The necessity and value of this resistor
will be dependent upon the logic family used.
Figure 40. Unipolar Buffered Voltage Output
POWER AND GROUNDING CONSIDERATIONS
In systems seeking to simultaneously achieve high speed and
high performance, the implementation and construction of the
printed circuit board design is often as important as the circuit
design. Proper RF techniques must be used in device selection,
placement and routing and supply bypassing and grounding.
Figures 44–49 illustrate the recommended printed circuit board
ground, power and signal plane layouts that are implemented on
the AD9774 evaluation board.
Proper grounding and decoupling should be a primary objective
in any high speed, high resolution system. The AD9774 features
separate analog and digital supply and ground pins to optimize
the management of analog and digital ground currents in a
system. In general, AVDD, the analog supply, should be decoupled
For a more detailed discussion of the implementation and con-
struction of high speed, mixed signal printed circuit boards,
refer to Analog Devices’ application notes AN-280 and AN-333.
REV. B
–17–
AD9774
MULTITONE PERFORMANCE CONSIDERATIONS AND
CHARACTERIZATION
tones) centered around one-half the Nyquist bandwidth (i.e.,
fCLOCK/4). This particular multitone vector, has a peak-to-rms
ratio of 13.5 dB compared to a sine waves peak-to-rms ratio of
3 dB. A “snapshot” of this reconstructed multitone vector in the
time domain as shown in Figure 43b reveals the higher signal
content around the midscale value. As a result, a DAC’s “small-
scale” dynamic and static linearity becomes increasingly critical in
obtaining low intermodulation distortion and maintaining
sufficient carrier-to-noise ratios for a given modulation scheme.
The frequency domain performance of high speed DACs has
traditionally been characterized by analyzing the spectral output
of a reconstructed full-scale (i.e., 0 dBFS), single-tone sine wave
at a particular output frequency and update rate. Although this
characterization data is useful, it is often insufficient to reflect a
DAC’s performance for a reconstructed multitone or spread-
spectrum waveform. In fact, evaluating a DAC’s spectral
performance using a full-scale, single tone at the highest specified
frequency (i.e., fH) of a bandlimited waveform is typically
indicative of a DAC’s “worst-case” performance for that given
waveform. In the time domain, this full-scale sine wave repre-
A DAC’s small-scale linearity performance is also an important
consideration in applications where additive dynamic range is
required for gain control purposes or “predistortion” signal
conditioning. For instance, a DAC with sufficient dynamic
range can be used to provide additional gain control of its
reconstructed signal. In fact, the gain can be controlled in
6 dB increments by simply performing a shift left or right on the
DAC’s digital input word. Other applications may intentionally
predistort a DAC’s digital input signal to compensate for
nonlinearities associated with the subsequent analog compo-
nents in the signal chain. For example, the signal compression
associated with a power amplifier can be compensated for by
predistorting the DAC’s digital input with the inverse nonlinear
transfer function of the power amplifier. In either case, the
DAC’s performance at reduced signal levels should be carefully
evaluated.
sents the lowest peak-to-rms ratio or crest factor (i.e., VPEAK
/
V rms) that this bandlimited signal will encounter.
0
–10
–20
–30
–40
–50
–60
–70
–80
A full-scale single tone will induce all of the dynamic and static
nonlinearities present in a DAC that contribute to its distortion
and hence SFDR performance. As the frequency of this recon-
structed full-scale, single-tone waveform increases, the dynamic
nonlinearities of any DAC (i.e., AD9774) tend to dominate thus
contributing to the roll-off in its SFDR performance. However,
unlike most DACs, which employ an R-2R ladder for the lower
bit current segmentation, the AD9774 (as well as other TxDAC
members) exhibits an improvement in distortion performance as
the amplitude of a single tone is reduced from its full-scale level.
This improvement in distortion performance at reduced signal
levels is evident if one compares the SFDR performance vs.
frequency at different amplitudes (i.e., 0 dBFS, –6 dBFS and
–12 dBFS) and sample rates as shown in Figures 4 through 15.
Maintaining decent “small-scale” linearity across the full span of
a DAC transfer function is also critical in maintaining excellent
multitone performance.
–90
–100
0
2
4
6
8
10
12
14
16
Figure 42a. Multitone Spectral Plot
1.0000
0.8000
0.6000
0.4000
0.2000
0.0000
–0.2000
–0.4000
–0.6000
–0.8000
–1.0000
Although characterizing a DAC’s multitone performance tends
to be application-specific, much insight into the potential per-
formance of a DAC can also be gained by evaluating the DAC’s
swept power (i.e., amplitude) performance for single, dual and
multitone test vectors at different clock rates and carrier frequen-
cies. The DAC is evaluated at different clock rates when recon-
structing a specific waveform whose amplitude is decreased in
3 dB increments from full-scale (i.e., 0 dBFS). For each specific
waveform, a graph showing the SFDR (over Nyquist) perfor-
mance vs. amplitude can be generated at the different tested
clock rates as shown in Figures 19 and 20. Note that the
carrier(s)-to-clock ratio remains constant in each figure.
TIME
Figure 42b. Time Domain “Snapshot” of the Multitone
Waveform
However, the inherent nature of a multitone, spread spectrum,
or QAM waveform, in which the spectral energy of the wave-
form is spread over a designated bandwidth, will result in a
higher peak-to-rms ratio when compared to the case of a simple
sine wave. As the reconstructed waveform’s peak-to-average
ratio increases, an increasing amount of the signal energy is
concentrated around the DAC’s midscale value. Figure 42a is
just one example of a bandlimited multitone vector (i.e., eight
–18–
REV. B
AD9774
80
75
70
65
60
55
50
45
40
A multitone test vector may consist of several equal amplitude,
spaced carriers each representative of a channel within a defined
bandwidth as shown in Figure 42a. In many cases, one or more
tones are removed so the intermodulation distortion performance
of the DAC can be evaluated. Nonlinearities associated with the
DAC will create spurious tones of which some may fall back into
the “empty” channel thus limiting a channel’s carrier-to-noise
ratio. Other spurious components falling outside the band of
interest may also be important, depending on the system’s spectral
mask and filtering requirements.
This particular test vector was centered around one-half the
Nyquist bandwidth (i.e., fCLOCK/4) with a passband of fCLOCK/16.
Centering the tones at a much lower region (i.e., fCLOCK/10)
would lead to an improvement in performance while centering
the tones at a higher region (i.e., fCLOCK/2.5) would result in a
degradation in performance. Figure 43a shows the SFDR vs.
amplitude at 32 MSPS up to the Nyquist frequency while Fig-
ure 43b shows the SFDR vs. amplitude within the passband of
the test vector. In assessing a DAC’s multitone performance, it
is also recommended that several units be tested under exactly
the same conditions to determine any performance variability.
–18 –16
–14
–12 –10
–8
– dBFS
–6
–4
–2
0
A
OUT
Figure 43a. Multitone SFDR vs. AOUT @ 32 MSPS
(Up to Nyquist)
80
8MSPS
75
16MSPS
32MSPS
70
65
60
55
50
AD9774 EVALUATION BOARD
General Description
The AD9774-EB is an evaluation board for the AD9774 14-bit
DAC converter. Careful attention to layout and circuit design,
combined with a prototyping area, allows the user to easily and
effectively evaluate the AD9774 in signal reconstruction applica-
tions, where high resolution, high speed conversion is required.
This board allows the user the flexibility to operate the AD9774
in various configurations. The digital inputs are designed to be
driven directly from various word generators with the onboard
option to add a resistor network for proper load termination.
Provisions are also made to operate the AD9774 with either the
internal or external reference or to exercise the SLEEP or
SNOOZE power-savings feature.
–18 –16
–14
–12 –10
–8
–6
–4
–2
0
A
– dBFS
OUT
Figure 43b. Multitone SFDR vs. AOUT @ 32 MSPS
(Within Multitone Passband)
REV. B
–19–
AD9774
DVDD
DGND
DGND
AVDD AGND
C2
TP TP
TP
C3
10F
TP14
TP15
TP17
TP16
10F
C1
0.1F
R2
50⍀
IA
C4
20pF
IDIFF
3
2
1
4
5
6
X 9
C12
0.1F
R10
100⍀
U7
U3
TP
C5
20pF
R3
50⍀
IB
50⍀
50⍀
TP
TP
C13
0.1F
TP
C6
0.1F
AGND
TP
TP TP
TP
42
44 43
41 40 39 38 37 36 35 34
REFCOMP
33
DCOM
1
U2,U4
33
FSADJ
DB13
DB12
DB11
DB10
DB9
32
2
1
TP
R1
1.91k⍀
REFIO
31
30
29
28
3
REFLO
C7
0.1F
4
J4
UNUSED
5
AD9774
TOP VIEW
(Not to Scale)
PLLENABLE
6
C10
0.1F
PLLCOM
DB8
27
26
25
24
TP19
C9
7
P
PLLVDD
PLLVDD
DB7
8
R5
TP 1.5k⍀
C8
0.01F
S3
10F
LPF
DB6
9
TP18
P
VCO IN/EXT
PLLDIVIDE
DB5
PLLGND
10
11
S2
S1
DB4
23
13
20
12
14 15 16 17 18 19
21 22
33
P
PLLGND
TP TP TP
C11
0.1F
P
DVDD
DGND
AVDD
PLLVDD
J2
P
J1
TP13
J8
EXT CLK
R4
50⍀
40
NC = NO CONNECT
U8
U6
Figure 44. Evaluation Board Schematic
–20–
REV. B
AD9774
Figure 45. Silkscreen Layer—Top
Figure 46. Component Side PCB Layout (Layer 1)
REV. B
–21–
AD9774
Figure 47. Ground Plane PCB Layout (Layer 2)
Figure 48. Power Plane PCB Layout (Layer 3)
–22–
REV. B
AD9774
Figure 49. Solder Side PCB Layout (Layer 4)
Figure 50. Silkscreen Layer—Bottom
–23–
REV. B
AD9774
OUTLINE DIMENSIONS
Dimensions shown in millimeters and (inches).
44-Lead Metric Quad Flatpack
(S-44)
13.45 (0.529)
12.95 (0.510)
2.45 (0.096)
10.10 (0.398)
MAX
9.90 (0.390)
1.03 (0.041)
0.73 (0.029)
0
°
44
34
MIN
1
33
SEATING
PLANE
8.45 (0.333)
8.30 (0.327)
TOP VIEW
(PINS DOWN)
11
23
0.25 (0.01)
MIN
12
22
0.23 (0.009)
0.13 (0.005)
0.80 (0.031)
BSC
0.45 (0.018)
0.30 (0.012)
2.10 (0.083)
1.95 (0.077)
–24–
REV. B
相关型号：
AD9774ASRL
PARALLEL, WORD INPUT LOADING, 0.035 us SETTLING TIME, 14-BIT DAC, PQFP44, MQFP-44
ROCHESTER
AD9775BSV
PARALLEL, WORD INPUT LOADING, 0.011 us SETTLING TIME, 14-BIT DAC, PQFP80, PLASTIC, MO-026-ADD-HD, TQFP-80
ROCHESTER
AD9775BSVRL
IC PARALLEL, WORD INPUT LOADING, 0.011 us SETTLING TIME, 14-BIT DAC, PQFP80, PLASTIC, MO-026-ADD-HD, TQFP-80, Digital to Analog Converter
ADI
AD9775BSVZ
PARALLEL, WORD INPUT LOADING, 0.011 us SETTLING TIME, 14-BIT DAC, PQFP80, LEAD FREE, PLASTIC, MO-026-ADD-HD, TQFP-80
ROCHESTER
©2020 ICPDF网 联系我们和版权申明