AD9775 [ADI]
14-Bit, 160 MSPS 2X/4X/8X Interpolating Dual TxDAC+ D/A Converter; 14位, 160 MSPS 2X / 4X / 8X插双通道TxDAC + D / A转换器型号: | AD9775 |
厂家: | ADI |
描述: | 14-Bit, 160 MSPS 2X/4X/8X Interpolating Dual TxDAC+ D/A Converter |
文件: | 总48页 (文件大小:5706K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
14-Bit, 160 MSPS 2
؋
/4؋
/8؋
®
a
Interpolating Dual TxDAC+ D/A Converter
AD9775*
FEATURES
APPLICATIONS
14-Bit Resolution, 160/400 MSPS Input/Output Data Rate
Selectable 2
؋
/4؋
/8؋
Interpolating Filter Programmable Channel Gain and Offset Adjustment
fS/4, fS/8 Digital Quadrature Modulation
Capability
Communications
Analog Quadrature Modulation Architectures
3G, Multicarrier GSM, TDMA, CDMA Systems
Broadband Wireless, Point-to-Point Microwave Radios
Instrumentation/ATE
Direct IF Transmission Mode for 70 MHz + IFs
Enables Image Rejection Architecture
Fully Compatible SPI Port
Excellent AC Performance
SFDR –71 dBc @ 2 MHz–35 MHz
WCDMA ACPR –71 dB @ IF = 71 MHz
Internal PLL Clock Multiplier
Selectable Internal Clock Divider
Versatile Clock Input
Differential/Single-Ended Sine Wave or
TTL/CMOS/LVPECL Compatible
Versatile Input Data Interface
GENERAL DESCRIPTION
The AD9775 is the 14-bit member of the AD977x pin-compatible,
high performance, programmable 2×/4×/8× interpolating TxDAC+
family. The AD977x family features a serial port interface (SPI)
providing a high level of programmability, thus allowing for
enhanced system-level options. These options include: select-
able 2×/4×/8× interpolation filters; fS/2, fS/4, or fS/8 digital
quadrature modulation with image rejection; a direct IF mode;
programmable channel gain and offset control; programmable
internal clock divider; straight binary or two’s complement data
interface; and a single-port or dual-port data interface.
Two’s Complement/Straight Binary Data Coding
Dual-Port or Single-Port Interleaved Input Data
Single 3.3 V Supply Operation
Power Dissipation: Typical 1.2 W @ 3.3 V
On-Chip 1.2 V Reference
The selectable 2×/4×/8× interpolation filters simplify the require-
ments of the reconstruction filters while simultaneously enhancing
the TxDAC+ family’s pass-band noise/distortion performance.
The independent channel gain and offset adjust registers allow
the user to calibrate LO feedthrough and sideband suppression
(continued on page 2)
80-Lead Thermally Enhanced TQFP Package
FUNCTIONAL BLOCK DIAGRAM
IDAC
COS
AD9775
HALF-
BAND
HALF-
BAND
HALF-
BAND
OFFSET
DAC
GAIN
DAC
*
*
*
FILTER 1
FILTER 2 FILTER 3
DATA
SIN
fDAC/2, 4, 8
SIN
ASSEMBLER
IMAGE
REJECTION/
DUAL DAC
MODE
BYPASS
MUX
16
16
16
16
16
I
I/Q DAC
GAIN/OFFSET
REGISTERS
LATCH
I AND Q
NONINTERLEAVED
OR
INTERLEAVED
DATA
16
16
Q
LATCH
16
16
16
FILTER
BYPASS
MUX
COS
WRITE
MUX
CONTROL
I
IDAC
OUT
SELECT
/2
(fDAC)
CLOCK OUT
/2
/2
/2
PRESCALER
SPI INTERFACE AND
CONTROL REGISTERS
DIFFERENTIAL
CLK
PHASE DETECTOR
AND VCO
*
HALF-BAND FILTERS ALSO CAN BE
CONFIGURED FOR "ZERO STUFFING ONLY"
PLL CLOCK MULTIPLIER AND CLOCK DIVIDER
TxDAC+ is a registered trademark of Analog Devices, Inc.
*Protected bu U.S. Patent Numbers 5568145, 5689257, and 5703519. Other Patents pending.
REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, norforanyinfringementsofpatentsorotherrightsofthirdpartiesthat
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
Fax: 781/326-8703
www.analog.com
© Analog Devices, Inc., 2002
AD9775
PRODUCT HIGHLIGHTS
(continued from page 1)
errors associated with analog quadrature modulators. The 6 dB
of gain adjustment range can also be used to control the output
power level of each DAC.
1.
The AD9775 is the 14-bit member of the AD977x pin-
compatible, high performance, programmable 2×/4×/8×
interpolating TxDAC+ family.
The AD9775 features the ability to perform fS/2, fS/4, and fS/8
digital modulation and image rejection when combined with an
analog quadrature modulator. In this mode, the AD9775 ac-
cepts I and Q complex data (representing a single or multicarrier
waveform), generates a quadrature modulated IF signal along with
its orthogonal representation via its dual DACs, and presents
these two reconstructed orthogonal IF carriers to an analog
quadrature modulator to complete the image rejection
upconversion process. Another digital modulation mode (i.e.,
the Direct IF Mode) allows the original baseband signal repre-
sentation to be frequency translated such that pairs of images fall
at multiples of one-half the DAC update rate.
2.
3.
Direct IF transmission capability for 70 MHz + IFs through
a novel digital mixing process.
fS/2, fS/4, and fS/8 digital quadrature modulation and user-
selectable image rejection to simplify/remove cascaded
SAW filter stages.
4.
5.
6.
7.
A 2×/4×/8× user-selectable interpolating filter eases data
rate and output signal reconstruction filter requirements.
User-selectable two’s complement/straight binary data
coding.
User-programmable channel gain control over 1 dB
range in 0.01 dB increments.
The AD977x family includes a flexible clock interface accepting
differential or single-ended sine wave or digital logic inputs. An
internal PLL clock multiplier is included and generates the
necessary on-chip high frequency clocks. It can also be disabled
to allow the use of a higher performance external clock source.
An internal programmable divider simplifies clock generation in
the converter when using an external clock source. A flexible data
input interface allows for straight binary or two’s complement
formats and supports single-port interleaved or dual-port data.
User-programmable channel offset control 10% over
the FSR.
8.
9.
Ultra high speed 400 MSPS DAC conversion rate.
Internal clock divider provides data rate clock for easy
interfacing.
10. Flexible clock input with single-ended or differential input,
CMOS, or 1 V p-p LO sine wave input capability.
11. Low power: Complete CMOS DAC operates on 1.2 W
from a 3.1 V to 3.5 V single supply. The 20 mA full-scale
current can be reduced for lower power operation and
several sleep functions are provided to reduce power dur-
ing idle periods.
Dual high performance DAC outputs provide a differential
current output programmable over a 2 mA to 20 mA range. The
AD9775 is manufactured on an advanced 0.35 micron CMOS
process, operates from a single supply of 3.1 V to 3.5 V, and
consumes 1.2 W of power.
12. On-chip voltage reference: The AD9775 includes a 1.20 V
temperature compensated band gap voltage reference.
Targeted at wide dynamic range, multicarrier and multistandard
systems, the superb baseband performance of the AD9775 is ideal
for wideband CDMA, multicarrier CDMA, multicarrier TDMA,
multicarrier GSM, and high performance systems employing
high order QAM modulation schemes. The image rejection
feature simplifies and can help to reduce the number of signal
band filters needed in a transmit signal chain. The direct IF
mode helps to eliminate a costly mixer stage for a variety of
communications systems.
13. 80-lead thermally enhanced TQFP.
–2–
REV. 0
AD9775
AD9775–SPECIFICATIONS
(TMIN to TMAX, AVDD = 3.3 V, CLKVDD = 3.3 V, DVDD = 3.3 V, PLLVDD = 3.3 V, IOUTFS = 20 mA, unless
otherwise noted.)
DC SPECIFICATIONS
Parameter
Min
Typ
Max
Unit
RESOLUTION
14
Bits
DC Accuracy1
Integral Nonlinearity
Differential Nonlinearity
–5
–3
1.5
1.0
+5
+3
LSB
LSB
ANALOG OUTPUT (for IR and 2R Gain Setting Modes)
Offset Error
–0.02
–1.0
–1.0
2
0.01
0.1
+0.02
+1.0
+1.0
20
% of FSR
% of FSR
% of FSR
mA
Gain Error (With Internal Reference)
Gain Matching
Full-Scale Output Current2
Output Compliance Range
–1.0
+1.25
V
Output Resistance
Output Capacitance
200
3
kΩ
pF
Gain, Offset Cal DACs, Monotonicity Guaranteed
REFERENCE OUTPUT
Reference Voltage
1.14
0.1
1.20
100
1.26
1.25
V
nA
Reference Output Current3
REFERENCE INPUT
Input Compliance Range
V
Reference Input Resistance (REFLO = 3 V)
Small Signal Bandwidth
10
0.5
MΩ
MHz
TEMPERATURE COEFFICIENTS
Offset Drift
Gain Drift (With Internal Reference)
Reference Voltage Drift
0
50
ppm of FSR/°C
ppm of FSR/°C
ppm/°C
POWER SUPPLY
AVDD
Voltage Range
3.1
3.1
3.3
72.5
23.3
3.5
76
26
V
mA
mA
4
Analog Supply Current (IAVDD
IAVDD in SLEEP Mode
CLKVDD
)
Voltage Range
3.3
8.5
3.5
V
mA
4
Clock Supply Current (ICLKVDD
CLKVDD (PLL ON)
Clock Supply Current (ICLKVDD
DVDD
)
)
23.5
mA
Voltage Range
Digital Supply Current (IDVDD
3.1
3.3
34
3.5
41
V
mA
4
)
Nominal Power Dissipation
PDIS
380
1.75
6.0
0.4
410
mW
W
mW
% of FSR/V
5
P
DIS IN PWDN
Power Supply Rejection Ratio—AVDD
OPERATING RANGE
–40
+85
°C
NOTES
1Measured at IOUTA driving a virtual ground.
2Nominal full-scale current, IOUTFS, is 32× the IREF current.
3Use an external amplifier to drive any external load.
4100 MSPS fDAC with fOUT = 1 MHz, all supplies = 3.3 V, no interpolation, no modulation.
5400 MSPS fDAC = 50 MSPS, fS/2 modulation, PLL enabled.
Specifications subject to change without notice.
–3–
REV. 0
AD9775
DYNAMIC SPECIFICATIONS
(TMIN to TMAX, AVDD = 3.3 V, CLKVDD = 3.3 V, DVDD = 3.3 V, PLLVDD = 0 V, IOUTFS = 20 mA,
Interpolation = 2
؋
, Differential Transformer Coupled Output, 50 ⍀ Doubly Terminated, unless otherwise noted.)
Parameter
Min
Typ
Max
Unit
DYNAMIC PERFORMANCE
Maximum DAC Output Update Rate (fDAC
Output Settling Time (tST) (to 0.025%)
Output Rise Time (10% to 90%)*
Output Fall Time (10% to 90%)*
Output Noise (IOUTFS = 20 mA)
)
400
MSPS
ns
ns
ns
pA√Hz
11
0.8
0.8
50
AC LINEARITY—–BASEBAND MODE
Spurious-Free Dynamic Range (SFDR) to Nyquist (fOUT = 0 dBFS)
fDATA = 100 MSPS, fOUT = 1 MHz
fDATA = 65 MSPS, fOUT = 1 MHz
71
73
84.5
84
80
84
80
dBc
dBc
dBc
dBc
dBc
dBc
dBc
f
DATA = 65 MSPS, fOUT = 15 MHz
fDATA = 78 MSPS, fOUT = 1 MHz
fDATA = 78 MSPS, fOUT = 15 MHz
f
DATA = 160 MSPS, fOUT = 1 MHz
82
80
fDATA = 160 MSPS, fOUT = 15 MHz
Spurious-Free Dynamic Range within a 1 MHz Window
(fOUT = 0 dBFS, fDATA = 100 MSPS, fOUT = 1 MHz)
Two-Tone Intermodulation (IMD) to Nyquist (fOUT1 = fOUT2 = –6 dBFS)
fDATA = 65 MSPS, fOUT1 = 10 MHz; fOUT2 = 11 MHz
91.3
dBc
81
76
81
76
81
76
dBc
dBc
dBc
dBc
dBc
dBc
f
DATA = 65 MSPS, fOUT1 = 20 MHz; fOUT2 = 21 MHz
fDATA = 78 MSPS, fOUT1 = 10 MHz; fOUT2 = 11 MHz
fDATA = 78 MSPS, fOUT1 = 20 MHz; fOUT2 = 21 MHz
f
DATA = 160 MSPS, fOUT1 = 10 MHz; fOUT2 = 11 MHz
fDATA = 160 MSPS, fOUT1 = 20 MHz; fOUT2 = 21 MHz
Total Harmonic Distortion (THD)
fDATA = 100 MSPS, fOUT = 1 MHz; 0 dBFS
Signal-to-Noise Ratio (SNR)
fDATA = 78 MSPS, fOUT = 5 MHz; 0 dBFS
–71
–82.5
dB
76
74
dB
dB
f
DATA = 160 MSPS, fOUT = 5 MHz; 0 dBFS
Adjacent Channel Power Ratio (ACLR)
WCDMA with 3.84 MHz BW, 5 MHz Channel Spacing
IF = Baseband, fDATA = 76.8 MSPS
75
73
dBc
dBc
IF = 19.2 MHz, fDATA = 76.8 MSPS
Four-Tone Intermodulation
21 MHz, 22 MHz, 23 MHz, and 24 MHz at –12 dBFS
(fDATA = MSPS, Missing Center)
75
dBFS
AC LINEARITY—IF MODE
Four-Tone Intermodulation at IF = 200 MHz
MHz, MHz, MHz, and MHz at dBFS
(fDATA = MSPS, fDAC = MHz)
72
dBFS
*Measured single-ended into 50 Ω load.
Specifications subject to change without notice.
–4–
REV. 0
AD9775
(TMIN to TMAX, AVDD = 3.3 V, CLKVDD = 3.3 V, PLLVDD = 0 V, DVDD = 3.3 V, IOUTFS = 20 mA, unless
otherwise noted.)
DIGITAL SPECIFICATIONS
Parameter
Min
Typ
Max
Unit
DIGITAL INPUTS
Logic “1” Voltage
Logic “0” Voltage
Logic “1” Current
Logic “0” Current
Input Capacitance
2.1
3
0
V
V
µA
µA
pF
0.9
+10
+10
–10
–10
5
CLOCK INPUTS
Input Voltage Range
Common-Mode Voltage
Differential Voltage
0
0.75
0.5
3
2.25
V
V
V
1.5
1.5
Specifications subject to change without notice.
ABSOLUTE MAXIMUM RATINGS*
Parameter
With Respect to
Min
Max
Unit
AVDD, DVDD, CLKVDD
AVDD, DVDD, CLKVDD
AGND, DGND, CLKGND
REFIO, REFLO, FSADJ1/2
IOUTA, IOUTB
P1B13–P1B0, P2B13–P2B0
DATACLK, PLL_LOCK
CLK+, CLK–, RESET
LPF
SPI_CSB, SPI_CLK,
SPI_SDIO, SPI_SDO
Junction Temperature
Storage Temperature
Lead Temperature (10 sec)
AGND, DGND, CLKGND
AVDD, DVDD, CLKVDD
AGND, DGND, CLKGND
AGND
AGND
DGND
DGND
CLKGND
CLKGND
DGND
–0.3
–4.0
–0.3
–0.3
–1.0
–0.3
–0.3
–0.3
–0.3
–0.3
+4.0
+4.0
+0.3
AVDD + 0.3
AVDD + 0.3
DVDD + 0.3
DVDD + 0.3
CLKVDD + 0.3
CLKVDD + 0.3
DVDD + 0.3
V
V
V
V
V
V
V
V
V
V
+125
+150
+300
°C
°C
°C
–65
*Stresses above those listed under the ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only; functional
operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute
maximum ratings for extended periods may affect device reliability.
ORDERING GUIDE
THERMAL CHARACTERISTICS
Thermal Resistance
80-Lead Thermally Enhanced
Temperature
Range
Package
Description
Package
Option*
Model
TQFP Package JA = 23.5 °C/W*
AD9775BSV –40°C to +85°C 80-Lead TQFP
SV-80
*With thermal pad soldered to PCB.
AD9775EB
Evaluation Board
*SV = Thin Plastic Quad Flatpack
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the AD9775 features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
–5–
REV. 0
AD9775
PIN CONFIGURATION
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
1
2
CLKVDD
LPF
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
FSADJ1
FSADJ2
REFIO
RESET
SPI_CSB
SPI_CLK
SPI_SDIO
SPI_SDO
DGND
DVDD
PIN 1
IDENTIFIER
3
CLKVDD
CLKGND
CLK+
4
5
6
CLK–
7
CLKGND
DATACLK/PLL_LOCK
DGND
8
AD9775
TxDAC+
TOP VIEW
(Not to Scale)
9
10
11
12
13
14
15
16
17
18
19
20
DVDD
P1B13 (MSB)
P1B12
NC
NC
P1B11
P2B0 (LSB)
P2B1
P1B10
P1B9
P2B2
P1B8
P2B3
DGND
DGND
DVDD
DVDD
P1B7
P2B4
P1B6
P2B5
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
NC = NO CONNECT
–6–
REV. 0
AD9775
PIN FUNCTION DESCRIPTIONS
Description
Pin Number
Mnemonic
1, 3
2
CLKVDD
LPF
Clock Supply Voltage
PLL Loop Filter
4, 7
5
6
CLKGND
CLK+
CLK–
Clock Supply Common
Differential Clock Input
Differential Clock Input
8
DATACLK/PLL_LOCK
With the PLL enabled, this pin indicates the state of the PLL. A read of a
Logic “1” indicates the PLL is in the locked state. Logic “0” indicates the
PLL has not achieved lock. This pin may also be programmed to act as
either an input or output (Address 02h, Bit 3) DATACLK signal running at
the input data rate.
9, 17, 25, 35, 44, 52
DGND
Digital Common
10, 18, 26, 36, 43, 51 DVDD
Digital Supply Voltage
11–16, 19–24, 27, 28 P1B13 (MSB) to P1B0 (LSB) Port “1” Data Inputs
29, 30, 49, 50
31
NC
No Connect
IQSEL/P2B13 (MSB)
In “1” port mode, IQSEL = 1 followed by a rising edge of the differential
input clock will latch the data into the I channel input register. IQSEL = 0
will latch the data into the Q channel input register. In “2” port mode, this
pin becomes the port “2” MSB.
32
ONEPORTCLK/P2B12
With the PLL disabled and the AD9775 in “1” port mode, this pin becomes
a clock output that runs at twice the input data rate of the I and Q channels.
This allows the AD9775 to accept and demux interleaved I and Q data to
the I and Q input registers.
33, 34, 37–42, 45–48 P2B11 to P2B0 (LSB)
Port “2” Data Inputs
53
54
55
56
57
SPI_SDO
SPI_SDIO
SPI_CLK
SPI_CSB
RESET
In the case where SDIO is an input, SDO acts as an output. When SDIO
becomes an output, SDO enters a High-Z state.
Bidirectional Data Pin. Data direction is controlled by Bit 7 of Register
Address 00h. The default setting for this bit is “0,” which sets SDIO as an input.
Data input to the SPI port is registered on the rising edge of SPI_CLK.
Data output on the SPI port is registered on the falling edge.
Chip Select/SPI Data Synchronization. On momentary logic high, resets
SPI port logic and initializes instruction cycle.
Logic “1” resets all of the SPI port registers, including Address 00h, to their
default values. A software reset can also be done by writing a Logic “1” to
SPI Register 00h, Bit 5. However, the software reset has no effect on the bits
in Address 00h.
58
59
60
REFIO
FSADJ2
FSADJ1
Reference Output, 1.2 V Nominal
Full-Scale Current Adjust, Q Channel
Full-Scale Current Adjust, I Channel
Analog Supply Voltage
61, 63, 65, 76, 78, 80 AVDD
62, 64, 66, 67, 70, 71, AGND
74, 75, 77, 79
Analog Common
68, 69
72, 73
I
OUTA2, IOUTB2
Differential DAC Current Outputs, Q Channel
Differential DAC Current Outputs, I Channel
IOUTA1, IOUTB1
REV. 0
–7–
AD9775
DIGITAL FILTER SPECIFICATIONS
20
0
Half-Band Filter No. 1 (43 Coefficients)
–20
–40
–60
–80
–100
Tap
Coefficient
1, 43
2, 42
3, 41
4, 40
5, 39
6, 38
7, 37
8, 36
8
0
–29
0
67
0
–134
0
244
0
–414
0
673
0
–1079
0
1772
0
–3280
0
–120
9, 35
0
0.5
1.0
1.5
2.0
f
– Normalized to Input Data Rate
OUT
10, 34
11, 33
12, 32
13, 31
14, 30
15, 29
16, 28
17, 27
18, 26
19, 25
20, 24
21, 23
22
Figure 1a. 2
؋
Interpolating Filter Response 20
0
–20
–40
–60
10364
16384
–80
–100
Half-Band Filter No. 2 (19 Coefficients)
Tap
Coefficient
–120
0
0.5
1.0
1.5
2.0
f
– Normalized to Input Data Rate
1, 19
2, 18
3, 17
4, 16
5, 15
6, 14
7, 13
8, 12
9, 11
10
19
0
–120
0
438
0
–1288
0
5047
8192
OUT
Figure 1b. 4
؋
Interpolating Filter Response 20
0
–20
–40
–60
Half-Band Filter No. 3 (11 Coefficients)
–80
Tap
Coefficient
–100
1, 11
2, 10
3, 9
4, 8
5, 7
6
7
0
–53
0
302
512
–120
0
2
4
6
8
f
– Normalized to Input Data Rate
OUT
Figure 1c. 8
؋
Interpolating Filter Response –8–
REV. 0
AD9775
DEFINITIONS OF SPECIFICATIONS
Monotonicity
A D/A converter is monotonic if the output either increases
or remains constant as the digital input increases.
Adjacent Channel Power Ratio (ACPR)
A ratio in dBc between the measured power within a channel
relative to its adjacent channel.
Offset Error
The deviation of the output current from the ideal of “0” is
called offset error. For IOUTA, 0 mA output is expected when the
inputs are all “0.” For IOUTB, 0 mA output is expected when all
inputs are set to “1.”
Complex Image Rejection
In a traditional two-part upconversion, two images are created
around the second IF frequency. These images are redundant
and have the effect of wasting transmitter power and system
bandwidth. By placing the real part of a second complex modu-
lator in series with the first complex modulator, either the upper
or lower frequency image near the second IF can be rejected.
Output Compliance Range
The range of allowable voltage at the output of a current output
DAC. Operation beyond the maximum compliance limits may
cause either output stage saturation or breakdown, resulting in
nonlinear performance.
Complex Modulation
The process of passing the real and imaginary components of a
signal through a complex modulator (transfer function = ejt
=
Pass Band
cost + jsint) and realizing real and imaginary components on
the modulator output.
Frequency band in which any input applied therein passes
unattenuated to the DAC output.
Differential Nonlinearity (DNL)
Power Supply Rejection
DNL is the measure of the variation in analog value, normalized
to full scale, associated with a 1 LSB change in digital input code.
The maximum change in the full-scale output as the supplies
are varied from minimum to maximum specified voltages.
Gain Error
Settling Time
The difference between the actual and ideal output span. The
actual span is determined by the output when all inputs are set
to “1,” minus the output when all inputs are set to “0.”
The time required for the output to reach and remain within a
specified error band about its final value, measured from the
start of the output transition.
Glitch Impulse
Signal-to-Noise Ratio (SNR)
Asymmetrical switching times in a DAC give rise to undesired
output transients that are quantified by a glitch impulse. It is
specified as the net area of the glitch in pV–S.
SNR is the ratio of the rms value of the measured output signal
to the rms sum of all other spectral components below the
Nyquist frequency, excluding the first six harmonics and dc.
The value for SNR is expressed in decibels.
Group Delay
Number of input clocks between an impulse applied at the
device input and peak DAC output current. A half-band FIR
filter has constant group delay over its entire frequency range.
Spurious-Free Dynamic Range
The difference, in dB, between the rms amplitude of the output
signal and the peak spurious signal over the specified bandwidth.
Impulse Response
Stop-Band Rejection
Response of the device to an impulse applied to the input.
The amount of attenuation of a frequency outside the pass band
applied to the DAC, relative to a full-scale signal applied at the
DAC input within the pass band.
Interpolation Filter
If the digital inputs to the DAC are sampled at a multiple rate of
fDATA (interpolation rate), a digital filter can be constructed
with a sharp transition band near fDATA/2. Images that would
typically appear around fDAC (output data rate) can be greatly
suppressed.
Temperature Drift
Temperature drift is specified as the maximum change from the
ambient (25°C) value to the value at either TMIN or TMAX. For
offset and gain drift, the drift is reported in ppm of full-scale
range (FSR) per °C. For reference drift, the drift is reported in
ppm per °C.
Linearity Error (Also Called Integral Nonlinearity or INL)
Linearity error is defined as the maximum deviation of the actual
analog output from the ideal output, determined by a straight
line drawn from zero to full scale.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of the first six harmonic com-
ponents to the rms value of the measured fundamental. It is
expressed as a percentage or in decibels (dB).
REV. 0
–9–
AD9775–Typical Performance Characteristics
(T = 25؇C, AVDD = 3.3 V, CLKVDD = 3.3 V, DVDD = 3.3 V, IOUTFS = 20 mA, Interpolation = 2
؋
, Differential Coupled Transformer Output, 50 ⍀ Doubly Terminated, unless otherwise noted.)
90
85
90
85
10
0dBFS
0
–6dBFS
–6dBFS
0dBFS
–10
–20
–30
–40
–50
–60
–70
–80
–90
80
75
70
65
60
55
50
80
75
70
65
60
55
50
–12dBFS
–12dBFS
0
5
10
15
20
25
30
0
5
10
15
20
25
30
0
65
130
FREQUENCY – MHz
FREQUENCY – MHz
FREQUENCY – MHz
TPC 1. Single-Tone Spec-
trum @ fDATA = 65 MSPS with
fOUT = fDATA/3
TPC 2. In-Band SFDR vs. fOUT
@ fDATA = 65 MSPS
TPC 3. Out-of-Band SFDR vs.
f
OUT @ fDATA = 65 MSPS
10
90
85
90
85
80
75
70
65
60
55
50
0dBFS
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–6dBFS
0dBFS
80
75
70
65
60
55
50
–12dBFS
–6dBFS
–12dBFS
0
50
100
150
0
5
10
15
20
25
30
0
5
10
15
20
25
30
FREQUENCY – MHz
FREQUENCY – MHz
FREQUENCY – MHz
TPC 4. Single-Tone Spec-
trum @ fDATA = 78 MSPS with
fOUT = fDATA/3
TPC 5. In-Band SFDR vs. fOUT
@ fDATA = 78 MSPS
TPC 6. Out-of-Band SFDR vs.
fOUT @ fDATA = 78 MSPS
90
85
80
75
70
65
60
55
50
10
90
85
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
0dBFS
–6dBFS
80
75
70
65
60
55
50
0dBFS
–6dBFS
–12dBFS
–12dBFS
10
0
100
200
300
0
20
30
40
50
0
10
20
30
40
50
FREQUENCY – MHz
FREQUENCY – MHz
FREQUENCY – MHz
TPC 8. In-Band SFDR vs. fOUT
@ fDATA = 160 MSPS
TPC 9. Out-of-Band SFDR vs.
fOUT @ fDATA = 160 MSPS
TPC 7. Single-Tone Spec-
trum @ fDATA = 160 MSPS
with fOUT = fDATA/3
–10–
REV. 0
AD9775
(T = 25؇C, AVDD = 3.3 V, CLKVDD = 3.3 V, DVDD = 3.3 V, IOUTFS = 20 mA, Interpolation = 2
؋
, Differential Coupled Transformer Output, 50 ⍀ Doubly Terminated, unless otherwise noted.)
90
85
80
75
70
65
60
55
50
90
85
90
85
–6dBFS
–6dBFS
–3dBFS
0dBFS
–6dBFS
80
75
70
65
60
55
50
80
75
70
65
60
55
50
–3dBFS
0dBFS
–3dBFS
0dBFS
0
5
10
15
20
25
30
0
5
10
15
20
25
30
0
10
20
30
40
50
60
FREQUENCY – MHz
FREQUENCY – MHz
FREQUENCY – MHz
TPC 10. Third Order IMD
Products vs. fOUT @ fDATA
65 MSPS
TPC 12. Third Order IMD
Products vs. fOUT @ fDATA
160 MSPS
TPC 11. Third Order IMD
Products vs. fOUT @ fDATA
78 MSPS
=
=
=
90
85
90
85
80
75
70
65
60
55
50
90
85
4
؋
8
؋
8
؋
0dBFS
80
75
70
65
60
55
50
80
75
70
65
60
55
50
4
؋
2
؋
1
؋
1
؋
2
؋
–6dBFS
–12dBFS
0
10
20
30
40
55
60
–15
–10
–5
– dBFS
0
3.1
3.2
3.3
AVDD – V
3.4
3.5
FREQUENCY – MHz
A
OUT
TPC 14. Third Order IMD
TPC 13. Third Order IMD
Products vs. fOUT and
Interpolation Rate,
1
؋
fDATA = 160 MSPS, 2
؋
fDATA = 160 MSPS, 4
؋
fDATA = 80 MSPS, 8
؋
fDATA = 50 MSPS TPC 15. SFDR vs. AVDD @
fOUT = 10 MHz, fDAC = 320 MSPS,
fDATA = 160 MSPS
Products vs. AOUT and Inter-
polation Rate fDATA = 50
MSPS for All Cases,
1
؋
fDAC = 50 MSPS, 2
؋
fDAC = 100 MSPS, 4
؋
fDAC = 200 MSPS, 8
؋
fDAC = 400 MSPS 90
90
85
90
78MSPS
–3dBFS
85
85
80
75
80
75
70
65
60
55
50
80
75
70
65
60
55
50
0dBFS
–6dBFS
PLL OFF
PLL ON
160MSPS
FDATA = 65MSPS
70
65
60
55
50
0
50
100
150
–50
0
50
100
3.1
3.2
3.3
3.4
3.5
INPUT DATA RATE – MSPS
TEMPERATURE – ؇C
AVDD – V
TPC 17. SNR vs. Data Rate
for fOUT = 5 MHz
TPC 18. SFDR vs. Temperature
@ fOUT = fDATA/11
TPC 16. Third Order IMD
Products vs. AVDD @ fOUT
10 MHz, fDAC = 320 MSPS,
fDATA = 160 MSPS
=
–11–
REV. 0
AD9775
(T = 25؇C, AVDD = 3.3 V, CLKVDD = 3.3 V, DVDD = 3.3 V, IOUTFS = 20 mA, Interpolation = 2
؋
, Differential Coupled Transformer Output, 50 ⍀ Doubly Terminated, unless otherwise noted.)
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
0
–20
–40
–60
–80
–100
0
50
100
150
0
10
20
30
40
50
0
50
100
150
200
250
300
FREQUENCY – MHz
FREQUENCY – MHz
FREQUENCY – MHz
TPC 20. Two-Tone IMD Per-
formance, fDATA = 150 MSPS,
No Interpolation
TPC 19. Single-Tone Spuri-
ous Performance, fOUT
10 MHz, fDATA = 150 MSPS,
No Interpolation
TPC 21. Single-Tone Spuri-
ous Performance, fOUT
10 MHz, fDATA = 150 MSPS,
=
=
Interpolation = 2
؋
0
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–10
–20
–30
–40
–50
–60
–40
–80
–90
–100
0
50
100
150
200
250
300
0
5
10
15
20
25
0
5
10 15 20 25 30 35 40 45 50
FREQUENCY – MHz
FREQUENCY – MHz
FREQUENCY – MHz
TPC 24. Two-Tone IMD Per-
formance, fOUT = 10 MHz,
fDATA = 50 MSPS, Interpola-
tion = 8
؋
TPC 22. Two-Tone IMD Per-
formance, fDATA = 150 MSPS,
Interpolation = 4
؋
TPC 23. Single-Tone Spuri-
ous Performance, fOUT
10 MHz, fDATA = 80 MSPS,
=
Interpolation = 4
؋
0
–20
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–40
–60
–80
–100
–120
0
20
40
60
80
0
100
200
300
400
FREQUENCY – MHz
FREQUENCY – MHz
TPC 25. Single-Tone Spuri-
ous Performance, fOUT
TPC 26. Eight-Tone IMD
Performance, fDATA
=
=
10 MHz, fDATA = 50 MSPS,
160 MSPS, Interpolation = 8
؋
Interpolation = 8
؋
–12–
REV. 0
AD9775
MODE CONTROL (VIA SPI PORT)
Table I. Mode Control via SPI Port
(Default Values Are Highlighted)
Address Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
00h
01h
02h
SDIO
LSB, MSB First
0 = MSB
1 = LSB
Software Reset on Sleep Mode
Power-Down Mode
1R/2R Mode
PLL_LOCK
Indicator
Bidirectional
0 = Input
1 = I/O
Logic “1”
Logic “1” shuts down Logic “1” shuts down
DAC output current set
by one or two external
resistors.
the DAC output
currents.
all digital and analog
functions.
0 = 2R, 1 = 1R
Filter
Interpolation
Rate
Filter
Interpolation
Rate
Modulation
Mode
(None, fS/2,
fS/4, fS/8)
Modulation Mode
(None, fS/2, fS/4, fS/8) on Interpolation
Filters, Logic “1”
0 = No Zero Stuffing
1 = Real Mix Mode
0 = Complex
Mix Mode
0 = e–j
DATACLK/
PLL_LOCK
Select
0 = PLLLOCK
1 = DATACLK
1 = e+j
(1×, 2×, 4×, 8×)
(1×, 2×, 4×, 8×)
enables zero stuffing.
0 = Signed Input 0 = Two Port Mode
Data
1 = Unsigned
DATACLK Driver DATACLK Invert
ONEPORTCLK Invert
0 = No Invert
1 = Invert
IQSEL Invert
0 = No Invert
1 = Invert
Q First
0 = I First
1 = Q First
1 = One Port Mode
Strength
0 = No Invert
1 = Invert
03h
04h
PLL Divide
(Prescaler) Ratio
PLL Divide
(Prescaler) Ratio
0 = PLL OFF
1 = PLL ON
0 = Automatic
Charge Pump Control
1 = Programmable
PLL Charge Pump
Control
PLL Charge Pump
Control
PLL Charge Pump
Control
05h
06h
07h
08h
IDAC Fine Gain
Adjustment
IDAC Fine Gain
Adjustment
IDAC Fine Gain
Adjustment
IDAC Fine Gain
Adjustment
IDAC Fine Gain
Adjustment
IDAC Fine Gain
Adjustment
IDAC Fine Gain
Adjustment
IDAC Fine Gain
Adjustment
IDAC Coarse Gain
Adjustment
IDAC Coarse Gain
Adjustment
IDAC Coarse Gain
Adjustment
IDAC Coarse Gain
Adjustment
IDAC Offset
Adjustment Bit 9
IDAC Offset
Adjustment Bit 8
IDAC Offset
Adjustment Bit 7
IDAC Offset
Adjustment Bit 6
IDAC Offset
Adjustment Bit 5
IDAC Offset
Adjustment Bit 4
IDAC Offset
Adjustment Bit 3
IDAC Offset
Adjustment Bit 2
IDAC IOFFSET
Direction
IDAC Offset
Adjustment Bit 1
IDAC Offset
Adjustment Bit 0
0 = IOFFSET
on IOUTA
1 = IOFFSET on
IOUTB
09h
0Ah
0Bh
0Ch
QDAC Fine Gain
Adjustment
QDAC Fine Gain
Adjustment
QDAC Fine Gain
Adjustment
QDAC Fine Gain
Adjustment
QDAC Fine Gain
Adjustment
QDAC Fine Gain
Adjustment
QDAC Fine Gain
Adjustment
QDAC Fine Gain
Adjustment
QDAC Coarse
Gain Adjustment
QDAC Coarse
Gain Adjustment
QDAC Coarse
Gain Adjustment
QDAC Coarse
Gain Adjustment
QDAC Offset
Adjustment Bit 9
QDAC Offset
Adjustment Bit 8
QDAC Offset
Adjustment Bit 7
QDAC Offset
Adjustment Bit 6
QDAC Offset
Adjustment Bit 5
QDAC Offset
Adjustment Bit 4
QDAC Offset
Adjustment Bit 3
QDAC Offset
Adjustment Bit 2
QDAC IOFFSET
Direction
QDAC Offset
Adjustment Bit 1
QDAC Offset
Adjustment Bit 0
0 = IOFFSET
on IOUTA
1 = IOFFSET
on IOUTB
0Dh
Version Register
Version Register
Version Register
Version Register
REV. 0
–13–
AD9775
REGISTER DESCRIPTION
Address 00h
Bit 3
Bit 2
Logic “1” enables zero stuffing mode for interpo-
lation filters.
Bit 7
Logic “0” (default). Causes the SDIO pin to act as
Default (“1”) enables the real mix mode. The I and
Q data channels are individually modulated by fS/2,
fS/4, or fS/8 after the interpolation filters. However, no
complex modulation is done. In the complex mix
mode (Logic “0”), the digital modulators on the I
and Q data channels are coupled to create a digi-
tal complex modulator. When the AD9775 is
applied in conjunction with an external quadrature
modulator, rejection can be achieved of either the
higher or lower frequency image around the second
IF frequency (i.e., the second IF frequency is the
LO of the analog quadrature modulator external to
the AD9775) according to the bit value of Register
01h, Bit 1.
an input during the data transfer (Phase 2) of the
communications cycle. When set to “1,” SDIO
can act as an input or output, depending on Bit 7 of
the instruction byte.
Bit 6
Bit 5
Logic “0” (default). Determines the direction
(LSB/MSB first) of the communications and data
transfer communications cycles. Refer to the section
MSB/LSB Transfers for a detailed description.
Writing a “1” to this bit resets the registers to their
default values and restarts the chip. The RESET bit
always reads back “0.” Register Address 00h bits are
not cleared by this software reset. However, a high
level at the RESET pin forces all registers, including
those in Address 00h, to their default state.
Bit 1
Bit 0
Logic “0” (default) causes the complex modulation
to be of the form e–jt, resulting in the rejection of
the higher frequency image when the AD9775 is used
with an external quadrature modulator. A Logic “1”
causes the modulation to be of the form e+jt, which
causes rejection of the lower frequency image.
Bit 4
Bit 3
Bit 2
Sleep Mode. A Logic “1” to this bit shuts down the
DAC output currents.
Power-Down. Logic “1” shuts down all analog and
digital functions except for the SPI port.
1R/2R Mode. The default (“0”) places the AD9775
in two resistor mode. In this mode, the IREF currents
for the I and Q DAC references are set separately by
the RSET resistors on FSADJ1 and FSADJ2 (Pins
59 and 60). In the 2R mode, assuming the coarse
gain setting is full scale and the fine gain setting is
zero, IFULLSCALE1 = 32 × VREF/FSADJ1 and
IFULLSCALE2 = 32 × VREF/FSADJ2. With this bit set
to “1,” the reference currents for both I and Q
DACs are controlled by a single resistor on Pin 60.
IFULLSCALE in one resistor mode for both of the I
and Q DACs is half of what it would be in the 2R
mode, assuming all other conditions (RSET, register
settings) remain unchanged. The full-scale current
of each DAC can still be set to 20 mA by choosing
a resistor of half the value of the RSET value used in
the 2R mode.
In two port mode, a Logic “0” (default) causes Pin 8
to act as a lock indicator for the internal PLL. A
Logic “1” in this register causes Pin 8 to act as a
DATACLK, either generating or acting as an input
clock (see Register 02h, Bit 3) at the input data rate
of the AD9775.
Address 02h
Bit 7
Logic “0” (default) causes data to be accepted on
the inputs as two’s complement binary. Logic “1”
causes data to be accepted as straight binary.
Bit 6
Logic “0” (default) places the AD9775 in two port
mode. I and Q data enters the AD9775 via Ports 1
and 2, respectively. A Logic “1” places the AD9775
in one port mode in which interleaved I and Q data
is applied to Port 1. See the Pin Function Descrip-
tions for DATACLK/PLL_LOCK, IQSEL, and
ONEPORTCLK for detailed information on how
to use these modes.
Bit 1
PLL_LOCK Indicator. When the PLL is enabled,
reading this bit will give the status of the PLL. A
Logic “1” indicates the PLL is locked. A Logic “0”
indicates an unlocked state.
Bit 5
DATACLK Driver Strength. With the internal PLL
disabled, and this bit set to Logic “0,” it is recom-
mended that DATACLK be buffered. When this bit
is set to Logic “1,” DATACLK acts as a stronger
driver capable of driving small capacitive loads.
Address 01h
Bits 7, 6
Filter interpolation rate according to the follow-
ing table:
Bit 4
Bit 2
Bit 1
Default Logic “0.” A value of “1” inverts DATACLK
at Pin 8.
00
1×
2×
4×
8×
01
10
11
Default Logic “0.” A value of 1 inverts
ONEPORTCLK at Pin 32.
Bits 5, 4
Modulation mode according to the following table:
The default of Logic “0” causes IQSEL = 1 to
direct input data to the I channel, while IQSEL = 0
directs input data to the Q channel. A Logic “1” in
this register inverts the sense of IQSEL.
00
01
10
11
none
fS/2
fS/4
fS/8
Bit 0
The default of Logic “0” defines IQ pairing as IQ,
IQ...while programming a Logic “1” causes the pair
ordering to be QI, QI...
–14–
REV. 0
AD9775
Address 05h, 09h
Bits 7–0
Address 03h
These bits represent an 8-bit binary number (Bit 7
MSB) that defines the fine gain adjustment of the I
(05h) and Q (09h) DAC, according to the equation
given below.
Bits 1, 0
Setting this divide ratio to a higher number allows
the VCO in the PLL to run at a high rate (for best
performance) while the DAC input and output clocks
run substantially slower. The divider ratio is set
according to the following table:
Address 06h, 0Ah
Bits 3–0 These bits represent a 4-bit binary number (Bit 3 MSB)
00
Ϭ1
Ϭ2
Ϭ4
Ϭ8
that defines the coarse gain adjustment of the I (06h)
and Q (0Ah) DACs according to the equation below.
01
10
11
Address 07h, 0Bh
Bits 7–0
Address 04h
Bit 7
Logic “0” (default) disables the internal PLL. Logic
“1” enables the PLL.
Address 08h, 0Ch
Bit 1, 0
The 10 bits from these two address pairs (07h, 08h
and 0Bh, 0Ch) represent a 10-bit binary number
that defines the offset adjustment of the I and Q
DACs according to the equation below (07h, 0Bh–Bit
7 MSB/08h, 0Ch–Bit 0 LSB)
Bit 6
Logic “0” (default) sets the charge pump control to
automatic. In this mode, the charge pump bias
current is controlled by the divider ratio defined in
Address 03h, Bits 1 and 0. Logic “1” allows the
user to manually define the charge pump bias cur-
rent using Address 04h, Bits 2, 1, and 0. Adjusting
the charge pump bias current allows the user to
optimize the noise/settling performance of the PLL.
Address 08h, 0Ch
Bit 7
This bit determines the direction of the offset of the
I (08h) and Q (0Ch) DACs. A Logic “0” will apply
a positive offset current to IOUTA, while a Logic “1”
will apply a positive offset current to IOUTB. The
magnitude of the offset current is defined by the
bits in Addresses 07h, 0Bh, 08h, and 0Ch accord-
ing to the formulas given below.
Bits 0, 1, 2 With the charge pump control set to manual, these
bits define the charge pump bias current according
to the following table:
000
001
010
011
100
50 µA
100 µA
200 µA
400 µA
800 µA
6 × IREF
3 × IREF
COARSE +1
FINE
256
1024 DATA
IOUTA
=
=
–
–
×
×
214
8
16
32
24
14
6 × IREF
3 × IREF
COARSE +1
FINE
1024 2 – DATA – 1
(1)
IOUTB
214
24
8
16
32
256
OFFSET
IOFFSET = 4 × I
REF
1024
Equation 1 shows IOUTA and IOUTB as a function of fine gain, coarse gain, and offset adjustment when using the 2R mode. In the 1R
mode, the current IREF is created by a single FSADJ resistor (Pin 60). This current is divided equally into each channel so that a
scaling factor of one-half must be added to these equations for full-scale currents for both DACs and the offset.
REV. 0
–15–
AD9775
FUNCTIONAL DESCRIPTION
SERIAL INTERFACE FOR REGISTER CONTROL
The AD9775 dual interpolating DAC consists of two data chan-
nels that can be operated completely independently or coupled to
form a complex modulator in an image reject transmit architec-
ture. Each channel includes three FIR filters, making the
AD9775 capable of 2×, 4×, or 8× interpolation. High speed input
and output data rates can be achieved within the following
limitations.
The AD9775 serial port is a flexible, synchronous serial com-
munications port allowing easy interface to many industry
standard microcontrollers and microprocessors. The serial I/O
is compatible with most synchronous transfer formats, including
both the Motorola SPI and Intel SSR protocols. The interface
allows read/write access to all registers that configure the AD9775.
Single- or multiple-byte transfers are supported as well as MSB
first or LSB first transfer formats. The AD9775’s serial interface
port can be configured as a single pin I/O (SDIO) or two unidi-
rectional pins for in/out (SDIO/SDO).
Interpolation
Rate (MSPS)
Input Data
Rate (MSPS)
DAC Sample
Rate (MSPS)
1×
2×
4×
8×
160
160
100
50
160
320
400
400
GENERAL OPERATION OF THE SERIAL INTERFACE
There are two phases to a communication cycle with the AD9775.
Phase 1 is the instruction cycle, which is the writing of an instruc-
tion byte into the AD9775 coincident with the first eight SCLK
rising edges. The instruction byte provides the AD9775 serial
port controller with information regarding the data transfer
cycle, which is Phase 2 of the communication cycle. The Phase 1
instruction byte defines whether the upcoming data transfer is
read or write, the number of bytes in the data transfer, and the
starting register address for the first byte of the data transfer.
The first eight SCLK rising edges of each communication cycle
are used to write the instruction byte into the AD9775.
Both data channels contain a digital modulator capable of mix-
ing the data stream with an LO of fDAC/2, fDAC/4, or fDAC/8,
where fDAC is the output data rate of DAC. A zero stuffing fea-
ture is also included and can be used to improve pass-band
flatness for signals being attenuated by the SIN(x)/x characteristic
of the DAC output. The speed of the AD9775, combined with
the digital modulation capability, enables direct IF conversion
architectures at 70 MHz and higher.
A logic high on the CSB pin, followed by a logic low, will reset
the SPI port timing to the initial state of the instruction cycle.
This is true regardless of the present state of the internal regis-
ters or the other signal levels present at the inputs to the SPI
port. If the SPI port is in the midst of an instruction cycle or a
data transfer cycle, none of the present data will be written.
The digital modulators on the AD9775 can be coupled to form
a complex modulator. By using this feature with an external analog
quadrature modulator, such as Analog Devices’ AD8345, an
image rejection architecture can be enabled. To optimize the
image rejection capability, as well as LO feedthrough in this
architecture, the AD9775 offers programmable (via the SPI port)
gain and offset adjust for each DAC.
The remaining SCLK edges are for Phase 2 of the communica-
tion cycle. Phase 2 is the actual data transfer between the AD9775
and the system controller. Phase 2 of the communication cycle
is a transfer of 1, 2, 3, or 4 data bytes as determined by the
instruction byte. Normally, using one multibyte transfer is the
preferred method. However, single byte data transfers are useful
to reduce CPU overhead when register access requires one byte
only. Registers change immediately upon writing to the last bit of
each transfer byte.
Also included on the AD9775 are a phase-locked loop (PLL)
clock multiplier and a 1.20 V band gap voltage reference. With
the PLL enabled, a clock applied to the CLK+/CLK– inputs is
frequency multiplied internally and generates all necessary
internal synchronization clocks. Each 14-bit DAC provides two
complementary current outputs whose full-scale currents can
be determined either from a single external resistor or indepen-
dently from two separate resistors (see 1R/2R mode). The
AD9775 features a low jitter, differential clock input that
provides excellent noise rejection while accepting a sine or
square wave input. Separate voltage supply inputs are provided
for each functional block to ensure optimum noise and distor-
tion performance.
INSTRUCTION BYTE
The instruction byte contains the information shown below.
N1
N0
Description
0
0
1
1
0
1
0
1
Transfer 1 Byte
Transfer 2 Bytes
Transfer 3 Bytes
Transfer 4 Bytes
SLEEP and power-down modes can be used to turn off the DAC
output current (SLEEP) or the entire digital and analog sections
(power-down) of the chip. An SPI-compliant serial port is used
to program the many features of the AD9775. Note that in
power-down mode, the SPI port is the only section of the chip
still active.
SDO (PIN 53)
SDIO (PIN 54)
AD9775 SPI PORT
INTERFACE
SCLK (PIN 55)
CSB (PIN 56)
Figure 2. SPI Port Interface
–16–
REV. 0
AD9775
R/W
SDIO (Pin 54)—Serial Data I/O
Bit 7 of the instruction byte determines whether a read or a
write data transfer will occur after the instruction byte write.
Logic high indicates read operation. Logic “0” indicates a write
operation.
Data is always written into the AD9775 on this pin. However,
this pin can be used as a bidirectional data line. The configura-
tion of this pin is controlled by Bit 7 of Register Address 00h.
The default is Logic “0,” which configures the SDIO Pin as
unidirectional.
N1, N0
Bits 6 and 5 of the instruction byte determine the number of
bytes to be transferred during the data transfer cycle. The bit
decodes are shown in the following table:
SDO (Pin 53)—Serial Data Out
Data is read from this pin for protocols that use separate lines
for transmitting and receiving data. In the case where the AD9775
operates in a single bidirectional I/O mode, this pin does not
output data and is set to a high impedance state.
MSB
LSB
I7
R/W
I6
N1
I5
N0
I4
A4
I3
A3
I2
A2
I1
A1
I0
A0
MSB/LSB TRANSFERS
The AD9775 serial port can support both most significant bit
(MSB) first or least significant bit (LSB) first data formats. This
functionality is controlled by Register Address 00h, Bit 6. The
default is MSB first. When this bit is set active high, the AD9775
serial port is in LSB first format. That is, if the AD9775 is in
LSB first mode, the instruction byte must be written from least-
significant bit to most significant bit. Multibyte data transfers in
MSB format can be completed by writing an instruction byte
that includes the register address of the most significant byte. In
MSB first mode, the serial port internal byte address generator
decrements for each byte required of the multibyte communica-
tion cycle. Multibyte data transfers in LSB first format can be
completed by writing an instruction byte that includes the regis-
ter address of the least significant byte. In LSB first mode, the
serial port internal byte address generator increments for each
byte required of the multibyte communication cycle.
A4, A3, A2, A1, A0
Bits 4, 3, 2, 1, and 0 of the instruction byte determine which
register is accessed during the data transfer portion of the com-
munications cycle. For multibyte transfers, this address is the
starting byte address. The remaining register addresses are
generated by the AD9775.
SERIAL INTERFACE PORT PIN DESCRIPTIONS
SCLK (Pin 55)—Serial Clock
The serial clock pin is used to synchronize data to and from the
AD9775 and to run the internal state machines. SCLK maxi-
mum frequency is 15 MHz. All data input to the AD9775 is
registered on the rising edge of SCLK. All data is driven out of
the AD9775 on the falling edge of SCLK.
CSB (Pin 56)—Chip Select
The AD9775 serial port controller address will increment from
1Fh to 00h for multibyte I/O operations if the MSB first mode is
active. The serial port controller address will decrement from 00h
to 1Fh for multibyte I/O operations if the LSB first mode is active.
Active low input starts and gates a communication cycle. It
allows more than one device to be used on the same serial com-
munications lines. The SDO and SDIO pins will go to a high
impedance state when this input is high. Chip select should stay
low during the entire communication cycle.
DATA TRANSFER CYCLE
INSTRUCTION CYCLE
CS
SCLK
SDIO
SDO
R/W
I6
I5
(N)
I4
I3
I2
I1
I0
D7
D7
D6
D6
D2
D1
D0
D0
(N)
N
N
0
0
0
D2
D1
0
0
0
N
N
Figure 3a. Serial Register Interface Timing MSB First
INSTRUCTION CYCLE
DATA TRANSFER CYCLE
CS
SCLK
SDIO
I0
I1
I2
I3
I4
I5
I6
R/W
D0
D0
D1
D1
D2
D6
D6
D7
D7
(N)
(N)
0
0
0
N
N
D2
SDO
0
0
0
N
N
Figure 3b. Serial Register Interface Timing LSB First
–17–
REV. 0
AD9775
tDS
tSCLK
CS
SCLK
SDIO
tPWH
tPWL
tDS
tDH
INSTRUCTION BIT 7
INSTRUCTION BIT 6
Figure 4. Timing Diagram for Register Write to AD9775
CS
SCLK
tDV
SDIO
SDO
DATA BIT N
DATA BIT N–1
Figure 5. Timing Diagram for Register Read from AD9775
NOTES ON SERIAL PORT OPERATION
DAC OPERATION
The AD9775 serial port configuration bits reside in Bits 6 and 7
of Register Address 00h. It is important to note that the configura-
tion changes immediately upon writing to the last bit of the register.
For multibyte transfers, writing to this register may occur dur-
ing the middle of the communication cycle. Care must be taken
to compensate for this new configuration for the remaining
bytes of the current communication cycle.
The dual 14-bit DAC output of the AD9775, along with the
reference circuitry, gain, and offset registers, is shown in Figure 6.
Referring to the transfer functions in Equation 1, a reference
current is set by the internal 1.2 V reference, the external RSET
resistor, and the values in the coarse gain register. The fine gain
DAC subtracts a small amount from this and the result is input
to IDAC and QDAC, where it is scaled by an amount equal
to 1024/24. Figures 7a and 7b show the scaling effect of the
coarse and fine adjust DACs. IDAC and QDAC are PMOS
current source arrays, segmented in a 5-4-5 configuration. The
five most significant bits control an array of 31 current sources.
The next four bits consist of 15 current sources whose values
are all equal to 1/16 of an MSB current source. The five LSBs
are binary weighted fractions of the middle bit’s current sources.
All current sources are switched to either IOUTA or IOUTB, depend-
ing on the input code.
The same considerations apply to setting the reset bit in Register
Address 00h. All other registers are set to their default values, but
the software reset doesn’t affect the bits in Register Address 00h.
It is recommended to use only single-byte transfers when chang-
ing serial port configurations or initiating a software reset.
A write to Bits 1, 2, and 3 of Address 00h with the same logic
levels as for Bits 7, 6, and 5 (bit pattern: XY1001YX binary)
allows the user to reprogram a lost serial port configuration and
to reset the registers to their default values. A second write to
Address 00h with reset bit low and serial port configuration as
specified above (XY) reprograms the OSC IN multiplier set-
ting. A changed fSYSCLK frequency is stable after a maximum of
200 fMCLK cycles (equals wake-up time).
The fine adjustment of the gain of each channel allows for
improved balance of QAM modulated signals, resulting in
improved modulation accuracy and image rejection. In the
Applications section of this data sheet, performance data is
included that shows to what degree image rejection can be im-
proved when the AD9775 is used with an AD8345 quadrature
modulator from ADI.
–18–
REV. 0
AD9775
0
The offset control defines a small current that can be added to
IOUTA or IOUTB (not both) on the IDAC and QDAC. The selec-
tion of which IOUT this offset current is directed toward is
programmable via Register 08h, Bit 7 (IDAC) and Register 0Ch,
Bit 7 (QDAC). Figure 8 shows the scale of the offset current
that can be added to one of the complementary outputs on the
IDAC and QDAC. Offset control can be used for suppression of
LO leakage resulting from modulation of dc signal components.
If the AD9775 is dc-coupled to an external modulator, this
feature can be used to cancel the output offset on the AD9775
as well as the input offset on the modulator. Figure 9 shows a
typical example of the effect that the offset control has on LO
suppression.
–0.5
–1.0
1R MODE
–1.5
–2.0
–2.5
–3.0
2R MODE
0
5
10
15
20
OFFSET
FINE GAIN REGISTER CODE – Assuming
OFFSET
DAC
CONTROL
FINE
GAIN
DAC
RSET1, 2 = 1.9k⍀
REGISTERS
GAIN
CONTROL
Figure 7b. Fine Gain Effect on IFULLSCALE
REGISTERS
In Figure 9, the negative scale represents an offset added to
IOUTB, while the positive scale represents an offset added to
OUTA of the respective DAC. Offset Register 1 corresponds to
FINE
GAIN
DAC
I
I
IDAC
OUTA1
1.2VREF
REFIO
0.1F
I
OUTB1
IDAC, while Offset Register 2 corresponds to QDAC. Figure 9
represents the AD9775 synthesizing a complex signal that is then
dc-coupled to an AD8345 quadrature modulator with an LO of
800 MHz. The dc-coupling allows the input offset of the
AD8345 to be calibrated out as well. The LO suppression at
the AD8345 output was optimized first by adjusting Offset
Register 1 in the AD9775. When an optimal point was found
(roughly Code 54), this code was held in Offset Register 1, and
Offset Register 2 was adjusted. The resulting LO suppression
is 70 dBFS. These are typical numbers and the specific code for
optimization will vary from part to part.
COARSE COARSE
I
I
QDAC
OUTA2
GAIN
DAC
GAIN
DAC
OUTB2
FSADJ1
RSET1
FSADJ2
OFFSET
CONTROL
REGISTERS
OFFSET
DAC
GAIN
RSET2
CONTROL
REGISTERS
Figure 6. DAC Outputs, Reference Current Scaling, and
Gain/Offset Adjust
5
25
20
4
2R MODE
3
15
2R MODE
2
10
1R MODE
1R MODE
1
5
0
0
0
200
400
600
800
1000
0
5
10
15
20
COARSE GAIN REGISTER CODE – Assuming
COARSE GAIN REGISTER CODE – Assuming
RSET1, 2 = 1.9k⍀
RSET1, 2 = 1.9k⍀
Figure 8. DAC Output Offset Current
Figure 7a. Coarse Gain Effect on IFULLSCALE
REV. 0
–19–
AD9775
0
–10
–20
–30
–40
–50
–60
–70
–80
AD9775
1k
⍀
⍀
⍀
⍀
0.1F
OFFSET REGISTER 1 ADJUSTED
CLK+
1k
1k
1k
0.1F
ECL/PECL
CLKVDD
CLK–
0.1
F
CLKGND
OFFSET REGISTER 2
ADJUSTED, WITH OFFSET
REGISTER 1 SET
Figure 11. Differential Clock Driving Clock Inputs
A transformer, such as the T1-1T from Mini-Circuits, can also
be used to convert a single-ended clock to differential. This
method is used on the AD9775 evaluation board so that an exter-
nal sine wave with no dc offset can be used as a differential clock.
TO OPTIMIZED VALUE
–1024 –768
–512
–256
0
256
512
768
1024
DAC1, DAC2 – Offset Register Codes
Figure 9. Offset Adjust Control, Effect on LO
Suppression
PECL/ECL drivers require varying termination networks, the
details of which are left out of Figures 10 and 11 but can be found
in application notes such as AND8020/D from On Semiconductor.
These networks depend on the assumed transmission line imped-
ance and power supply voltage of the clock driver. Optimum
performance of the AD9775 is achieved when the driver is placed
very close to the AD9775 clock inputs, thereby negating any
transmission line effects such as reflections due to mismatch.
1R/2R MODE
In the 2R mode, the reference current for each channel is set
independently by the FSADJ resistor on that channel. The AD9775
can be programmed to derive its reference current from a single
resistor on Pin 60 by placing the part in the 1R mode. The trans-
fer functions in Equation 1 are valid for the 2R mode. In the
1R mode, the current developed in the single FSADJ resistor is
split equally between the two channels. The result is that in the
1R mode, a scale factor of one-half must be applied to the for-
mulas in Equation 1. The full-scale DAC current in the 1R mode
can still be set to as high as 20 mA by using the internal 1.2 V
reference and a 950 Ω resistor, instead of the 1.9 kΩ resistor
typically used in the 2R mode.
The quality of the clock and data input signals is important in
achieving optimum performance. The external clock driver cir-
cuitry should provide the AD9775 with a low jitter clock input
that meets the min/max logic levels while providing fast edges.
Although fast clock edges help minimize any jitter that will manifest
itself as phase noise on a reconstructed waveform, the high gain
bandwidth product of the AD9775’s differential comparator can
tolerate sine wave inputs as low as 0.5 V p-p, with minimal
degradation of the output noise floor.
CLOCK INPUT CONFIGURATIONS
The clock inputs to the AD9775 can be driven differentially or
single-ended. The internal clock circuitry has supply and ground
(CLKVDD, CLKGND) separate from the other supplies on the
chip to minimize jitter from internal noise sources.
PROGRAMMABLE PLL
CLKIN can function either as an input data rate clock (PLL
enabled) or as a DAC data rate clock (PLL disabled) according
to the state of Address 02h, Bit 7 in the SPI port register. The
internal operation of the AD9775 clock circuitry in these two
modes is illustrated in Figures 12 and 13.
Figure 10 shows the AD9775 driven from a single-ended clock
source. The CLK+/CLK– Pins form a differential input (CLKIN),
so that the statically terminated input must be dc-biased to the
midswing voltage level of the clock driven input.
The PLL clock multiplier and distribution circuitry produce the
necessary internal synchronized 1×, 2×, 4×, and 8× clocks for
the rising edge triggered latches, interpolation filters, modula-
tors, and DACs. This circuitry consists of a phase detector,
charge pump, voltage controlled oscillator (VCO), prescaler,
clock distribution, and SPI port control. The charge pump and
VCO are powered from PLLVDD while the differential clock
input buffer, phase detector, prescaler, and clock distribution
are powered from CLKVDD. PLL lock status is indicated by
the logic signal at the PLL_LOCK Pin, as well as by the status of
Bit 1, Register 00h. To ensure optimum phase noise performance
from the PLL clock multiplier and distribution, PLLVDD and
CLKVDD should originate from the same clean analog supply.
The speed of the VCO with the PLL enabled also has an effect
on phase noise. Optimal phase noise with respect to VCO speed
is achieved by running the VCO in the range of 450 MHz to
550 MHz. The VCO speed is a function of the input data rate,
the interpolation rate, and the VCO prescaler, according to the
following function:
AD9775
R
SERIES
CLK+
CLKVDD
CLK–
V
THRESHOLD
0.1µF
CLKGND
Figure 10. Single-Ended Clock Driving Clock Inputs
A configuration for differentially driving the clock inputs is given
in Figure 11. DC-blocking capacitors can be used to couple a
clock driver output whose voltage swings exceed CLKVDD or
CLKGND. If the driver voltage swings are within the supply
range of the AD9775, the dc-blocking capacitors and bias resistors
are not necessary.
VCO Speed (MHz) =
Input Data Rate (MHz) × InterpolationRate × Prescaler
–20–
REV. 0
AD9775
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
CLK–
CLK+
PLLVDD
PLL_LOCK
1 = LOCK
0 = NO LOCK
AD9775
INTERPOLATION
FILTERS,
MODULATORS,
AND DACS
PHASE
DETECTOR
CHARGE
PUMP
LPF
2
4
8
1
CLOCK
DISTRIBUTION
CIRCUITRY
PRESCALER
VCO
INPUT
DATA
LATCHES
0
1
2
3
4
5
PLL DIVIDER
(PRESCALER)
CONTROL
INTERNAL SPI
CONTROL
FREQUENCY OFFSET – MHz
REGISTERS
INTERPOLATION
RATE
CONTROL
Figure 14. Phase Noise Performance
PLL
CONTROL
(PLL ON)
MODULATION
RATE
CONTROL
It is important to note that the resistor/capacitor needed for the
PLL loop filter is internal on the AD9775. This will suffice unless
the input data rate is below 10 MHz, in which case an external
series RC is required between the LPF and PLLVDD pins.
SPI PORT
Figure 12. PLL and Clock Circuitry with PLL Enabled
POWER DISSIPATION
CLK–
CLK+
The AD9775 has three voltage supplies: AVDD, DVDD, and
CLKVDD. Figures 15, 16, and 17 show the current required
from each of these supplies when each is set to the 3.3 V nominal
specified for the AD9775. Power dissipation (PD) can easily be
extracted by multiplying the given curves by 3.3. As Figure 15
shows, IDVDD is very dependent on the input data rate, the interpo-
lation rate, and the activation of the internal digital modulator.
IDVDD, however, is relatively insensitive to the modulation rate
by itself. In Figure 16, IAVDD shows the same type of sensitivity
to the data, the interpolation rate, and the modulator function
but to a much lesser degree (<10%). In Figure 17, ICLKVDD
varies over a wide range yet is responsible for only a small per-
centage of the overall AD9775 supply current requirements.
PLL_LOCK
1 = LOCK
AD9775
0 = NO LOCK
INTERPOLATION
FILTERS,
MODULATORS,
AND DACS
PHASE
CHARGE
PUMP
DETECTOR
2
4
8
1
CLOCK
DISTRIBUTION
CIRCUITRY
PRESCALER
VCO
INPUT
DATA
LATCHES
PLL DIVIDER
(PRESCALER)
CONTROL
INTERNAL SPI
CONTROL
REGISTERS
400
INTERPOLATION
RATE
PLL
CONTROL
(PLL ON)
, (MOD. ON)
8
؋
MODULATION
RATE
CONTROL
CONTROL
2
, (MOD. ON)
؋
350
300
250
200
150
100
4
, (MOD. ON)
؋
SPI PORT
Figure 13. PLL and Clock Circuitry with PLL Disabled
8
؋
4
؋
2
؋
In addition, if the zero stuffing option is enabled, the VCO will
double its speed again. Phase noise may be slightly higher with
the PLL enabled. Figure 14 illustrates typical phase noise per-
formance of the AD9775 with 2× interpolation and various
input data rates. The signal synthesized for the phase noise
measurement was a single carrier at a frequency of fDATA/4. The
repetitive nature of this signal eliminated quantization noise and
distortion spurs as a factor in the measurement. Although the
curves blend together in Figure 14, the different conditions are
called out here for clarity.
1
؋
50
0
0
50
100
– MHz
150
200
f
DATA
Figure 15. IDVDD vs. fDATA vs. Interpolation Rate,
PLL Disabled
fDATA
PLL
Prescaler Ratio
125 MSPS
125 MSPS
100 MSPS
75 MSPS
50 MSPS
Disabled
Enabled
Enabled
Enabled
Enabled
div1
div2
div2
div4
REV. 0
–21–
AD9775
76.0
ONE/TWO PORT INPUT MODES
2
, (MOD. ON)
؋
8
, (MOD. ON)
؋
The digital data input ports can be configured as two independent
ports or as a single (one port mode) port. In two port mode, the
AD9775 can be programmed to generate an externally avail-
able data rate clock (DATACLK) for the purpose of data
synchronization. Data at the two input ports can be latched into
the AD9775 on every rising clock edge of DATACLK. In one
port mode, P2B12 and P2B13 from input data Port 2 are
redefined as IQSEL and ONEPORTCLK, respectively. The
input data in one port mode is steered to one of the two internal
data channels based on the logic level of IQSEL. A clock signal,
ONEPORTCLK, is generated by the AD9775 in this mode for
the purpose of external data synchronization. ONEPORTCLK
runs at the input interleaved data rate which is 2× the data rate
at the internal input to either channel.
75.5
75.0
4
, (MOD. ON)
؋
74.5
74.0
4
؋
8
؋
2
؋
73.5
73.0
72.5
1
؋
72.0
0
50
100
– MHz
150
200
f
DATA
Test configurations showing the various clocks that are required and
produced by the AD9775 in the PLL and one/two port modes
are given in Figures 55 through 58. Jumper positions needed to
operate the AD9775 evaluation board in these modes are given
as well.
Figure 16. IAVDD vs. fDATA vs. Interpolation Rate,
PLL Disabled
35
8
؋
30
25
20
15
10
PLL ENABLED, TWO PORT MODE
(Control Register 02h, Bits 6–0 and 04h, Bits 7–1)
2
4
؋
؋
With the phase-locked loop (PLL) enabled and the AD9775 in
two port mode, the speed of CLKIN is inherently that of the input
data rate. In two port mode, Pin 8 (DATACLK/PLL_ LOCK)
can be programmed (Control Register 01h, Bit 0) to function as
either a lock indicator for the internal PLL or as a clock running
at the input data rate. When Pin 8 is used as a clock output
(DATACLK), its frequency is equal to that of CLKIN. Data at
the input ports is latched into the AD9775 on the rising edge of the
CLKIN. Figure 18 shows the delay, tOD, inherent between the
rising edge of CLKIN and the rising edge of DATACLK, as well
as the setup and hold requirements for the data at Ports 1 and 2.
Note that the setup and hold times given in Figure 18 are the
input data transitions with respect to CLKIN. tOD can vary with
CLKIN speed, PLL divider setting, and interpolation rate. It is
therefore highly recommended that the input data be synchro-
nized to CLKIN rather than DATACLK when the PLL is enabled.
Note that in two port mode (PLL enabled or disabled), the data
rate at the interpolation filter inputs is the same as the input data
rate at Ports 1 and 2.
1
؋
5
0
0
50
100
– MHz
150
200
f
DATA
Figure 17. ICLKVDD vs. fDATA vs. Interpolation Rate,
PLL Disabled
SLEEP/POWER-DOWN MODES
(Control Register 00h, Bits 3 and 4)
The AD9775 provides two methods for programmable reduction
in power savings. The sleep mode, when activated, turns off the
DAC output currents but the rest of the chip remains functioning.
When coming out of sleep mode, the AD9775 will immediately
return to full operation. Power-down mode, on the other hand,
turns off all analog and digital circuitry in the AD9775 except
for the SPI port. When returning from power-down mode, enough
clock cycles must be allowed to flush the digital filters of random
data acquired during the power-down cycle.
The DAC output sample rate in two port mode is equal to the
clock input rate multiplied by the interpolation rate. If zero
stuffing is used, another factor of two must be included to calcu-
late the DAC sample rate.
DATACLK Inversion
(Control Register 02h, Bit 4)
By programming this bit, the DATACLK signal shown in
Figure 18 can be inverted. With inversion enabled, tOD will
refer to the time between the rising edge of CLKIN and the
falling edge of DATACLK. No other effect on timing will occur.
–22–
REV. 0
AD9775
tOD
to the internal input data rate of the I and Q channels. The
selection of the data for the I or the Q channel is determined by the
state of the logic level at Pin 31 (IQSEL when the AD9775 is in
one port mode) on the rising edge of ONEPORTCLK. IQSEL
= 1 under these conditions will latch the data into the I channel
on the clock rising edge, while IQSEL = 0 will latch the data into
the Q channel. It is possible to invert the I and Q selection by set-
ting control Register 02h, Bit 1 to the invert state (Logic “1”).
Figure 20 illustrates the timing requirements for the data inputs as
well as the IQSEL input. Note that the 1× interpolation rate is
not available in the one port mode.
CLKIN
DATACLK
The DAC output sample rate in one port mode is equal to CLKIN
multiplied by the interpolation rate. If zero stuffing is used, another
factor of two must be included to calculate the DAC sample rate.
DATA AT PORTS
1 AND 2
tS = 0.0ns
ONEPORTCLK INVERSION
(Control Register 02h, Bit 2)
tH = 2.5ns
tS
tH
(TYP SPECS)
By programming this bit, the ONEPORTCLK signal shown in
Figure 20 can be inverted. With inversion enabled, tOD refers to
the delay between the rising edge of the external clock and the
falling edge of ONEPORTCLK. The setup and hold times, tS
and tH, will be with respect to the falling edge of ONEPORTCLK.
There will be no other effect on timing.
Figure 18. Timing Requirements in Two Port
Input Mode, with PLL Enabled
DATACLK DRIVER STRENGTH
(Control Register 02h, Bit 5)
The DATACLK output driver strength is capable of driving
>10 mA into a 330 Ω load while providing a rise time of 3 ns.
Figure 19 shows DATACLK driving a 330 Ω resistive load at a
frequency of 50 MHz. By enabling the drive strength option
(Control Register 02h, Bit 5), the amplitude of DATACLK
under these conditions will be increased by approximately 200 mV.
ONEPORTCLK DRIVER STRENGTH
The drive capability of ONEPORTCLK is identical to that of
DATACLK in the two port mode. Refer to Figure 19 for perfor-
mance under load conditions.
tOD
3.0
2.5
2.0
1.5
1.0
0.5
tOD = 4.7ns
tS = 3.0ns
CLKIN
tH = –0.5ns
tIQS = 3.5ns
tIQH = –1.5ns
ONEPORTCLK
0
DELTA APPROX. 2.8ns
I AND Q INTERLEAVED
INPUT DATA AT PORT 1
–0.5
0
10
20
30
40
50
TIME – ns
Figure 19. DATACLK Driver Capability into 330 Ω
at 50 MHz
tS tH
IQSEL
PLL ENABLED, ONE PORT MODE
(Control Register 02h, Bits 6–1 and 04h, Bits 7–1)
In one port mode, the I and Q channels receive their data from an
interleaved stream at digital input Port 1. The function of Pin 32
is defined as an output (ONEPORTCLK) that generates a clock at
the interleaved data rate which is 2× the internal input data
rate of the I and Q channels. The frequency of CLKIN is equal
tIQS
tIQH
Figure 20. Timing Requirements in One Port
Input Mode with the PLL Enabled
REV. 0
–23–
AD9775
tOD
IQ PAIRING
(Control Register 02h, Bit 0)
In one port mode, the interleaved data is latched into the
AD9775 internal I and Q channels in pairs. The order of how
the pairs are latched internally is defined by this control register.
The following is an example of the effect this has on incoming
interleaved data.
CLKIN
Given the following interleaved data stream, where the data
indicates the value with respect to full scale:
DATACLK
I
Q
I
Q
1
I
Q
I
Q
0
I
Q
0.5
0.5
1
0.5 0.5
0
0.5 0.5
With the control register set to “0” (I first), the data will appear
at the internal channel inputs in the following order in time:
DATA AT PORTS
1 AND 2
I Channel
Q Channel
0.5
0.5
1
1
0.5
0.5
0
0
0.5
0.5
tS = 5.0ns
tH = –3.2ns
(TYP SPECS)
tS
tH
With the control register set to “1” (Q first), the data will appear at
the internal channel inputs in the following order in time:
Figure 21. Timing Requirements in Two Port
Input Mode with PLL Disabled
I Channel
Q Channel
0.5
y
1
0.5
0.5
1
0
0.5
0.5
0
x
0.5
PLL DISABLED, ONE PORT MODE
The values x and y represent the next I value and the previous
Q value in the series.
In one port mode, data is received into the AD9775 as an inter-
leaved stream on Port 1. A clock signal (ONEPORT CLK),
running at the interleaved data rate which is 2× the input data
rate of the internal I and Q channels is available for data syn-
chronization at Pin 32.
PLL DISABLED, TWO PORT MODE
With the PLL disabled, a clock at the DAC output rate must be
applied to CLKIN. Internal clock dividers in the AD9775 syn-
thesize the DATACLK signal at Pin 8, which runs at the input
data rate and can be used to synchronize the input data. Data is
latched into input Ports 1 and 2 of the AD9775 on the rising edge
of DATACLK. DATACLK speed is defined as the speed of
CLKIN divided by the interpolation rate. With zero stuffing
enabled, this division increases by a factor of 2. Figure 21
illustrates the delay between the rising edge of CLKIN and the
rising edge of DATACLK, as well as tS and tH in this mode.
With PLL disabled, a clock at the DAC output rate must be applied
to CLKIN. Internal dividers synthesize the ONEPORTCLK
signal at Pin 32. The selection of the data for the I or Q channel
is determined by the state of the logic level applied to Pin 31
(IQSEL when the AD9775 is in one port mode) on the rising
edge of ONEPORTCLK. IQSEL = 1 under these conditions
will latch the data into the I channel on the clock rising edge,
while IQSEL = 0 will latch the data into the Q channel. It is
possible to invert the I and Q selection by setting control
Register 02h, Bit 1 to the invert state (Logic “1”). Figure 22
illustrates the timing requirements for the data inputs as well as
the IQSEL input. Note that the 1ϫ interpolation rate is not
available in the one port mode.
The programmable modes DATACLK inversion and DATACLK
driver strength described in the previous section (PLL
Enabled, Two Port Mode) have identical functionality with
the PLL disabled.
As described earlier in the PLL-Enabled Mode section, tOD can
vary depending on CLKIN frequency and interpolation rate.
However, with the PLL disabled, the input data latches are
closely synchronized to DATACLK so that it is recommended
in this mode that the input data be timed from DATACLK, not CLKIN.
One port mode is very useful when interfacing with devices
such as Analog Devices’ AD6622 or AD6623 transmit signal
processors, in which two digital data channels have been inter-
leaved (multiplexed).
–24–
REV. 0
AD9775
AMPLITUDE MODULATION
The programmable modes’ ONEPORTCLK inversion,
ONEPORTCLK driver strength, and IQ pairing described in
the previous section (PLL Enabled, One Port Mode) have
identical functionality with the PLL disabled.
Given two sine waves at the same frequency, but with a 90 phase
difference, a point of view in time can be taken such that the
waveform that leads in phase is cosinusoidal and the waveform
that lags is sinusoidal. Analysis of complex variables states that
the cosine waveform can be defined as having real positive and
negative frequency components, while the sine waveform consists
of imaginary positive and negative frequency images. This is
shown graphically in the frequency domain in Figure 23.
tOD
CLKIN
–jt
e
/2j
SINE
ONEPORTCLK
DC
–jt
e
/2j
–jt
–jt
e
/2
e
/2
COSINE
I AND Q INTERLEAVED
INPUT DATA AT PORT 1
DC
Figure 23. Real and Imaginary Components of
Sinusoidal and Cosinusoidal Waveforms
tS tH
Amplitude modulating a baseband signal with a sine or a cosine
convolves the baseband signal with the modulating carrier in the
frequency domain. Amplitude scaling of the modulated signal
reduces the positive and negative frequency images by a factor of
two. This scaling will be very important in the discussion of the
various modulation modes. The phase relationship of the modu-
lated signals is dependent on whether the modulating carrier is
sinusoidal or cosinusoidal, again with respect to the reference
point of the viewer. Examples of sine and cosine modulation are
given in Figure 24.
IQSEL
tOD = 4.7ns
tS = 3.0ns
tH = –1.0ns
tIQS = 3.5ns
tIQH = –1.5ns
(TYP SPECS)
tIQS
tIQH
Figure 22. Timing Requirements in One Port
Input Mode with PLL Disabled
DIGITAL FILTER MODES
–jt
Ae
/2j
The I and Q data paths of the AD9775 have their own indepen-
dent half-band FIR filters. Each data path consists of three FIR
filters, providing up to 8× interpolation for each channel. The
rate of interpolation is determined by the state of Control Register
01h, Bits 7 and 6. Figures 1a–1c show the response of the digi-
tal filters when the AD9775 is set to 2×, 4×, and 8× modes. The
frequency axes of these graphs have been normalized to the input
data rate of the DAC. As the graphs show, the digital filters can
provide greater than 75 dB of out-of-band rejection.
SINUSOIDAL
MODULATION
DC
–jt
/2j
Ae
–jt
–jt
/2
Ae
/2
Ae
COSINUSOIDAL
MODULATION
DC
An online tool is available for quick and easy analysis of the
AD9775 interpolation filters in the various modes. The link
can be accessed at: www.analog.com/techSupport/designTools/
interactiveTools/dac/ad9777image.html.
Figure 24. Baseband Signal, Amplitude
Modulated with Sine and Cosine Carriers
REV. 0
–25–
AD9775
MODULATION, NO INTERPOLATION
characteristics required for the DAC reconstruction filter. Note
also, per the previous discussion on amplitude modulation, that
the spectral components (where modulation is set to fS/4 or fS/8)
are scaled by a factor of 2. In the situation where the modula-
tion is fS/2, the modulated spectral components add constructively
and there is no scaling effect.
With Control Register 01h, Bits 7 and 6 set to “00,” the inter-
polation function on the AD9775 is disabled. Figures 25a–25d
show the DAC output spectral characteristics of the AD9775 in
the various modulation modes, all with the interpolation filters
disabled. The modulation frequency is determined by the state
of Control Register 01h, Bits 5 and 4. The tall rectangles
represent the digital domain spectrum of a baseband signal of
narrow bandwidth. By comparing the digital domain spectrum
to the DAC SIN(x)/x roll-off, an estimate can be made for the
0
0
–20
–40
–20
–40
–60
–80
–60
–80
–100
–100
0
0.2
0.4
0.6
0.8
1.0
0
0.2
0.4
0.6
0.8
1.0
fOUT (
؋
fDATA )
fOUT (
؋
fDATA )
Figure 25a. No Interpolation, Modulation Disabled
Figure 25c. No Interpolation, Modulation = fDAC/4
0
0
–20
–40
–20
–40
–60
–80
–60
–80
–100
–100
0
0.2
0.4
0.6
0.8
1.0
0
0.2
0.4
0.6
0.8
1.0
fOUT (
؋
fDATA )
fOUT (
؋
fDATA )
Figure 25b. No Interpolation, Modulation = fDAC/2
Figure 25d. No Interpolation, Modulation = fDAC/8
Figure 25. Effects of Digital Modulation on DAC Output Spectrum, Interpolation Disabled
–26–
REV. 0
AD9775
MODULATION, INTERPOLATION = 2×
>70 dB. Another significant point is that the interpolation filter-
ing is done previous to the digital modulator. For this reason, as
Figures 26a–26d show, the pass band of the interpolation
filters can be frequency shifted, giving the equivalent of a
high pass digital filter.
With Control Register 01h, Bits 7 and 6 set to “01,” the inter-
polation rate of the AD9775 is 2×. Modulation is achieved by
multiplying successive samples at the interpolation filter output
by the sequence (1, –1). Figures 26a–26d represent the spectral
response of the AD9775 DAC output with 2× interpolation in
the various modulation modes to a narrow band baseband signal
(again, the tall rectangles in the graphic). The advantage of
interpolation becomes clear in Figures 26a–26d, where it can
be seen that the images that would normally appear in the spec-
trum around the input data rate frequency are suppressed by
Note that when using the fS/4 modulation mode, there is no true
stop band as the band edges coincide with each other. In the fS/8
modulation mode, amplitude scaling occurs over only a portion of
the digital filter pass band due to constructive addition over just
that section of the band.
0
0
–20
–40
–20
–40
–60
–80
–60
–80
–100
–100
0
0.5
1.0
fOUT (
؋
fDATA 1.5
2.0
0
0.5
1.0
fOUT (
؋
fDATA 1.5
2.0
)
)
Figure 26c. 2 × Interpolation, Modulation = fDAC/4
Figure 26a. 2 × Interpolation, Modulation = Disabled
0
0
–20
–40
–20
–40
–60
–80
–60
–80
–100
–100
0
0.5
1.0
fOUT (
؋
fDATA 1.5
2.0
0
0.5
1.0
fOUT (
؋
fDATA 1.5
2.0
)
)
Figure 26d. 2 × Interpolation, Modulation = fDAC/8
Figure 26b. 2 × Interpolation, Modulation = fDAC/2
Figure 26. Effects of Digital Modulation on DAC Output Spectrum, Interpolation = 2 ×
REV. 0
–27–
AD9775
MODULATION, INTERPOLATION = 4×
by the sequence (0, 1, 0, –1). Figures 27a–27d represent the
spectral response of the AD9775 DAC output with 4× interpo-
lation in the various modulation modes to a narrow band
baseband signal.
With Control Register 01h, Bits 7 and 6 set to “10,” the inter-
polation rate of the AD9775 is 4×. Modulation is achieved by
multiplying successive samples at the interpolation filter output
0
–20
–40
0
–20
–40
–60
–80
–60
–80
–100
–100
0
1
2
3
4
0
1
2
3
4
fOUT (
؋
fDATA )
fOUT (
؋
fDATA )
Figure 27a. 4 × Interpolation, Modulation Disabled
Figure 27c. 4 × Interpolation, Modulation = fDAC/4
0
0
–20
–40
–20
–40
–60
–80
–60
–80
–100
–100
0
1
2
3
4
0
1
2
3
4
fOUT (
؋
fDATA )
fOUT (
؋
fDATA )
Figure 27b. 4 × Interpolation, Modulation = fDAC/2
Figure 27d. 4 × Interpolation, Modulation = fDAC/8
Figure 27. Effect of Digital Modulation on DAC Output Spectrum, Interpolation = 4 ×
–28–
REV. 0
AD9775
MODULATION, INTERPOLATION = 8×
Looking at Figures 26–29, the user can see how higher interpola-
tion rates reduce the complexity of the reconstruction filter needed
at the DAC output. It also becomes apparent that the ability to
modulate by fS/2, fS/4, or fS/8 adds a degree of flexibility in
frequency planning.
With Control Register 01h, Bits 7 and 6 set to “11,” the
interpolation rate of the AD9775 is 8×. Modulation is achieved
by multiplying successive samples at the interpolation filter
output by the sequence (0, 0.707, 1, 0.707, 0, –0.707, –1, 0.707).
Figures 28a–28d represent the spectral response of the AD9775
DAC output with 8× interpolation in the various modulation
modes to a narrow band baseband signal.
0
–20
–40
0
–20
–40
–60
–80
–60
–80
–100
–100
0
1
2
3
4
0
1
2
3
4
5
6
7
8
fOUT (
؋
fDATA )
fOUT (
؋
fDATA )
Figure 28a. 8 × Interpolation, Modulation Disabled
Figure 28c. 8 × Interpolation, Modulation = fDAC/4
0
0
–20
–40
–20
–40
–60
–80
–60
–80
–100
–100
0
1
2
3
4
0
1
2
3
4
5
6
7
8
fOUT (
؋
fDATA )
fOUT (
؋
fDATA )
Figure 28b. 8 × Interpolation, Modulation = fDAC/2
Figure 28d. 8 × Interpolation, Modulation = fDAC/8
Figure 28. Effect of Digital Modulation on DAC Output Spectrum, Interpolation = 8 ×
Consider an application where the digital data into the AD9775
represents a baseband signal around fDAC/4 with a pass band of
fDAC/10. The reconstructed signal out of the AD9775 would
experience only a 0.75 dB amplitude variation over its pass band.
However, the image of the same signal occurring at 3 × fDAC/4
will suffer from a pass-band flatness variation of 3.93 dB. This
image may be the desired signal in an IF application using one
of the various modulation modes in the AD9775. This roll-off
of image frequencies can be seen in Figures 25 through 28,
where the effect of the interpolation and modulation rate is
apparent as well.
ZERO STUFFING
(Control Register 01h, Bit 3)
As shown in Figure 29, a “0” or null in the output frequency
response of the DAC (after interpolation, modulation, and DAC
reconstruction) occurs at the final DAC sample rate (fDAC).
This is due to the inherent SIN(x)/x roll-off response in the digital-
to-analog conversion. In applications where the desired frequency
content is below fDAC/2, this may not be a problem. Note that at
fDAC/2 the loss due to SIN(x)/x is 4 dB. In direct RF applica-
tions, this roll-off may be problematic due to the increased
pass band amplitude variation as well as the reduced amplitude
of the desired signal.
REV. 0
–29–
AD9775
If a complex modulation function (e+jt) is desired, the real and
imaginary components of the system correspond to the real and
imaginary components of e+jt, or cost and sint. As Figure
31 shows, the complex modulation function can be realized
by applying these components to the structure of the com-
plex system defined in Figure 30.
10
ZERO STUFFING
ENABLED
0
–10
–20
–30
–40
COMPLEX MODULATION AND IMAGE REJECTION OF
BASEBAND SIGNALS
ZERO STUFFING
DISABLED
In traditional transmit applications, a two-step upconversion is
done in which a baseband signal is modulated by one carrier to
an IF (intermediate frequency) and then modulated a second
time to the transmit frequency. Although this approach has
several benefits, a major drawback is that two images are cre-
ated near the transmit frequency. Only one image is needed, the
other being an exact duplicate. Unless the unwanted image is
filtered, typically with analog components, transmit power is
wasted and the usable bandwidth available in the system is
reduced.
–50
0
0.5
1.0
1.5
2.0
f
, NORMALIZED TO f
WITH ZERO STUFFING
OUT
DATA
DISABLED – Hz
Figure 29. Effect of Zero Stuffing on DAC’s SIN(x)/
x Response
To improve upon the pass-band flatness of the desired image,
the zero stuffing mode can be enabled by setting the control
register bit to a Logic “1.” This option increases the ratio of
fDAC/fDATA by a factor of 2 by doubling the DAC sample rate and
inserting a midscale sample (i.e., 1000 0000 0000 0000) after
every data sample originating from the interpolation filter. This
is important as it will affect the PLL divider ratio needed to keep
the VCO within its optimum speed range. Note that the zero
stuffing takes place in the digital signal chain at the output of the
digital modulator before the DAC.
A more efficient method of suppressing the unwanted image
can be achieved by using a complex modulator followed by a
quadrature modulator. Figure 32 is a block diagram of a
quadrature modulator. Note that it is in fact the real output half
of a complex modulator. The complete upconversion can actu-
ally be referred to as two complex upconversion stages, the real
output of which becomes the transmitted signal.
a(t)
c(t)
b(t) + d
b(t)
INPUT
OUTPUT
؋
؋
The net effect is to increase the DAC output sample rate by a
factor of 2× with the “0” in the SIN(x)/x DAC transfer function
occurring at twice the original frequency. A 6 dB loss in ampli-
tude at low frequencies is also evident, as can be seen in Figure 29.
COMPLEX FILTER
= (c + jd)
IMAGINARY
INPUT
b(t)
OUTPUT
b(t)
a(t) + c
b(t)
؋
؋
It is important to realize that the zero stuffing option by itself
does not change the location of the images but rather their ampli-
tude, pass-band flatness, and relative weighting. For instance, in
the previous example, the pass-band amplitude flatness of the
image at 3 × fDATA/4 is now improved to 0.59 dB while the signal
level has increased slightly from –10.5 dBFS to –8.1 dBFS.
Figure 30. Realization of a Complex System
INPUT
(REAL)
؋
OUTPUT
(REAL)
INPUT
(IMAGINARY)
؋
INTERPOLATING (COMPLEX MIX MODE)
90؇
(Control Register 01h, Bit 2)
In the complex mix mode, the two digital modulators on the
AD9775 are coupled to provide a complex modulation function.
In conjunction with an external quadrature modulator, this
complex modulation can be used to realize a transmit image
rejection architecture. The complex modulation function can be
programmed for e+jt or e–jt to give upper or lower image rejec-
tion. As in the real modulation mode, the modulation frequency
can be programmed via the SPI port for fDAC/2, fDAC/4, and
fDAC/8, where fDAC represents the DAC output rate.
OUTPUT
(IMAGINARY)
–jt
e
= COSt + jSINt
Figure 31. Implementation of a Complex Modulator
INPUT
؋
(REAL)
OUTPUT
INPUT
(IMAGINARY)
OPERATIONS ON COMPLEX SIGNALS
؋
Truly complex signals cannot be realized outside of a computer
simulation. However, two data channels, both consisting of real
data, can be defined as the real and imaginary components of a
complex signal. I (real) and Q (imaginary) data paths are often
defined this way. By using the architecture defined in Figure 30,
a system can be realized that operates on complex signals,
giving a complex (real and imaginary) output.
SINt
90؇
COSt
Figure 32. Quadrature Modulator
–30–
REV. 0
AD9775
The entire upconversion, from baseband to transmit frequency,
is represented graphically in Figure 33. The resulting spectrum
shown in Figure 33 represents the complex data consisting of
the baseband real and imaginary channels, now modulated onto
orthogonal (cosine and negative sine) carriers at the transmit
frequency. It is important to remember that in this application
(two baseband data channels) the image rejection is not
dependent on the data at either of the AD9775 input channels.
In fact, image rejection will still occur with either one or both of
the AD9775 input channels active. Note that by changing the sign
of the sinusoidal multiplying term in the complex modulator, the
upper sideband image could have been suppressed while passing
the lower one. This is easily done in the AD9775 by selecting
the e+jt bit (Register 01h, Bit 1). In purely complex terms,
Figure 31 represents the two-stage upconversion from complex
baseband to carrier.
REAL CHANNEL (OUT)
A/2
A/2
*
–F
F
C
C
REAL CHANNEL (IN)
A
–B/2J
B/2J
DC
–F
F
C
C
COMPLEX
MODULATOR
TO QUADRATURE
MODULATOR
IMAGINARY CHANNEL (OUT)
–A/2J A/2J
IMAGINARY CHANNEL (IN)
–F
–F
C
C
B
DC
B/2
B/2
–F
F
C
C
*F = COMPLEX MODULATION FREQUENCY
C
*F = QUADRATURE MODULATION FREQUENCY
Q
A/4 + B/4J A/4 – B/4J
A/4 + B/4J A/4 – B/4J
*
–F
F
Q
Q
–F – F
–F + F
F
– F
F + F
Q C
Q
C
Q
C
Q
C
OUT
REAL
–A/4 – B/4J A/4 – B/4J
A/4 + B/4J –A/4 + B/4J
QUADRATURE
MODULATOR
–F
F
Q
Q
IMAGINARY
REJECTED IMAGES
A/2 + B/2J
–F
A/2 – B/2J
F
Q
Q
Figure 33. Two-Stage Upconversion and Resulting Image Rejection
REV. 0
–31–
AD9775
COMPLEX BASEBAND
SIGNAL
imaginary inputs of the AD9775. A system in which multiple
baseband signals are complex modulated and then applied to
the AD9775 real and imaginary inputs followed by a quadrature
modulator is shown in Figure 36, which also describes the transfer
function of this system and the spectral output. Note the simi-
larity of the transfer functions given in Figure 36 and Figure 34.
Figure 36 adds an additional complex modulator stage for the
purpose of summing multiple carriers at the AD9775 inputs. Also,
as in Figure 33, the image rejection is not dependent on the real
or imaginary baseband data on any channel. Image rejection on
a channel will occur if either the real or imaginary data, or both,
is present on the baseband channel.
1
j(1 + 2)t
OUTPUT = REAL
1/2
؋
e
1/2
= REAL
–1 – 2
1 + 2
FREQUENCY
DC
Figure 34. Two-Stage Complex Upconversion
IMAGE REJECTION AND SIDEBAND SUPPRESSION OF
MODULATED CARRIERS
It is important to remember that the magnitude of a complex signal
can be 1.414× the magnitude of its real or imaginary components.
Due to this 3 dB increase in signal amplitude, the real and imagi-
nary inputs to the AD9775 must be kept at least 3 dB below full
scale when operating with the complex modulator. Overranging
in the complex modulator will result in severe distortion at the
DAC output.
As shown in Figure 33, image rejection can be achieved by applying
baseband data to the AD9775 and following the AD9775 with a
quadrature modulator. To process multiple carriers while still
maintaining image reject capability, each carrier must be complex
modulated. As Figure 34 shows, single- or multiple-complex
modulators can be used to synthesize complex carriers. These
complex carriers are then summed and applied to the real and
BASEBAND CHANNEL 1
R(1)
REAL INPUT
COMPLEX
MULTICARRIER
MODULATOR 1
REAL OUTPUT =
IMAGINARY INPUT
R(1)
R(1) + R(2) + ...R(N)
(TO REAL INPUT OF AD9775)
BASEBAND CHANNEL 2
REAL INPUT
R(2)
R(2)
COMPLEX
MODULATOR 2
MULTICARRIER
IMAGINARY INPUT
IMAGINARY OUTPUT =
I(1) + I(2) + ...I(N)
(TO IMAGINARY INPUT OF AD9775)
R(N) = REAL OUTPUT OF N
I(N) = IMAGINARY OUTPUT OF N
BASEBAND CHANNEL N
REAL INPUT
R(N)
R(N)
COMPLEX
MODULATOR N
IMAGINARY INPUT
Figure 35. Synthesis of Multicarrier Complex Signal
MULTIPLE
BASEBAND
CHANNELS
REAL
REAL
REAL
REAL
AD9775
MULTIPLE
COMPLEX
QUADRATURE
MODULATOR
FREQUENCY =
COMPLEX
MODULATOR
MODULATORS
IMAGINARY
IMAGINARY
IMAGINARY
Q
FREQUENCY = , ...
FREQUENCY =
1
2
N
C
COMPLEX BASEBAND
SIGNAL
OUTPUT = REAL
j( + + )t
e
N
C
Q
– – –
+ +
Q
DC
REJECTED IMAGES
1
C
Q
1
C
Figure 36. Image Rejection with Multicarrier Signals
–32–
REV. 0
AD9775
The complex carrier synthesized in the AD9775 digital modulator
is accomplished by creating two real digital carriers in quadrature.
Carriers in quadrature cannot be created with the modulator
running at fDAC/2. As a result, complex modulation only functions
with modulation rates of fDAC/4 and fDAC/8.
Region C
Region C is most accurately described as a down conversion, as the
modulating carrier is –ejt. If viewed as a complex signal, only the
images in Region C will remain. This image will appear on the
real and imaginary outputs of the AD9775, as well as on the
output of the quadrature modulator, where the center of the spec-
tral plot will now represent the quadrature modulator LO and the
horizontal scale will represent the frequency offset from this LO.
Regions A and B of Figures 37 through 42 are the result of the
complex signal described above, when complex modulated in the
AD9775 by +ejt. Regions C and D are the result of the complex
signal described above, again with positive frequency components
only, modulated in the AD9775 by –ejt. The analog quadra-
ture modulator after the AD9775 inherently modulates by +ejt.
Region D
Region D is the image (complex conjugate) of Region C. If a
spectrum analyzer is used to view the real or imaginary DAC
outputs of the AD9775, Region D will appear in the spectrum.
However, on the output of the quadrature modulator, Region D
will be rejected.
Region A
Region A is a direct result of the upconversion of the complex
signal near baseband. If viewed as a complex signal, only the
images in Region A will remain. The complex Signal A, consisting
of positive frequency components only in the digital domain, has
images in the positive odd Nyquist zones (1, 3, 5...) as well as
images in the negative even Nyquist zones. The appearance and
rejection of images in every other Nyquist zone will become
more apparent at the output of the quadrature modulator. The
A images will appear on the real and the imaginary outputs of
the AD9775, as well as on the output of the quadrature modula-
tor, where the center of the spectral plot will now represent the
quadrature modulator LO, and the horizontal scale now repre-
sents the frequency offset from this LO.
Figures 43 through 50 show the measured response of the AD9775
and AD8345 given the complex input signal to the AD9775 in
Figure 43. The data in these graphs was taken with a data rate of
12.5 MSPS at the AD9775 inputs. The interpolation rate of 4×or
8×gives a DAC output data rate of 50 MSPS or 100 MSPS. As a
result, the high end of the DAC output spectrum in these graphs
is the first null point for the SIN(x)/x roll-off, and the asymmetry
of the DAC output images is representative of the SIN(x)/x roll-off
over the spectrum. The internal PLL was enabled for these
results. In addition, a 35 MHz third order low-pass filter was
used at the AD9775/AD8345 interface to suppress DAC images.
Region B
An important point can be made by looking at Figures 45 and 47.
Figure 45 represents a group of positive frequencies modulated by
complex +fDAC/4, while Figure 47 represents a group of negative
frequencies modulated by complex –fDAC/4. When looking at the
real or imaginary outputs of the AD9775, as shown in Figures 45
and 47, the results look identical. However, the spectrum analyzer
cannot show the phase relationship of these signals. The differ-
ence in phase between the two signals becomes apparent when
they are applied to the AD8345 quadrature modulator, with the
results shown in Figures 46 and 48.
Region B is the image (complex conjugate) of Region A. If a spec-
trum analyzer is used to view the real or imaginary DAC outputs
of the AD9775, Region B will appear in the spectrum. However, on
the output of the quadrature modulator, Region B will be rejected.
REV. 0
–33–
AD9775
0
–20
–40
–60
0
–20
–40
–60
D
A
B
C
D
A
B
C
D
A
B
C D
A
B
C
–80
–80
–100
–100
–2.0
–1.5
–1.0
–0.5
0
(LO)
0.5
1.0
1.5
2.0
–2.0
–1.5
–1.0
–0.5
0
(LO)
0.5
1.0
1.5
2.0
fOUT (
؋
fDATA )
fOUT (
؋
fDATA )
Figure 40. 2× Interpolation, Complex fDAC/8 Modulation
Figure 37. 2× Interpolation, Complex fDAC/4 Modulation
0
–20
–40
0
–20
D
A
B
C
D
A
B
C
–40
–60
D
A
B
C
D
A
B
C
–60
–80
–80
–100
–100
–4.0
–3.0
–2.0
–1.0
0
1.0
2.0
3.0
4.0
–4.0
–3.0
–2.0
–1.0
0
1.0
2.0
3.0
4.0
(LO)
(LO)
fOUT (
؋
fDATA )
fOUT (
؋
fDATA )
Figure 41. 4× Interpolation, Complex fDAC/8 Modulation
Figure 38. 4× Interpolation, Complex fDAC/4 Modulation
0
0
–20
–20
D A
B C
D A
B C
D
A
B
C
D
A
B
C
–40
–60
–40
–60
–80
–80
–100
–100
–8.0
–6.0
–4.0
–2.0
0
(LO)
2.0
4.0
6.0
8.0
–8.0
–6.0
–4.0
–2.0
0
(LO)
2.0
4.0
6.0
8.0
fOUT (
؋
fDATA )
fOUT (
؋
fDATA )
Figure 42. 8× Interpolation, Complex fDAC/8 Modulation
Figure 39. 8× Interpolation, Complex fDAC/4 Modulation
–34–
REV. 0
AD9775
0
–10
–20
–30
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–40
–50
–60
–70
–80
–90
–100
0
10
20
30
40
50
0
20
FREQUENCY – MHz
40
50
30
10
FREQUENCY – MHz
Figure 43. AD9775, Real DAC Output of Complex
Input Signal Near Baseband (Positive Frequencies
Only), Interpolation = 4
؋
, No Modulation in AD9775
Figure 45. AD9775, Real DAC Output of Complex
Input Signal Near Baseband (Positive Frequencies
Only), Interpolation = 4
؋
, Complex Modulation in AD9775 = +fDAC/4
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–100
750 760 770 780 790 800 810 820 830 840 850
750 760 770 780 790 800 810 820 830 840 850
FREQUENCY – MHz
FREQUENCY – MHz
Figure 46. AD9775 Complex Output from
Figure 45, Now Quadrature Modulated
by AD8345 (LO = 800 MHz)
Figure 44. AD9775 Complex Output from
Figure 43, Now Quadrature Modulated by AD8345
(LO = 800 MHz)
*Windows is a registered trademark of Microsoft Corporation
REV. 0
–35–
AD9775
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
0
20
FREQUENCY – MHz
40
30
10
50
60
40
FREQUENCY – MHz
100
0
20
80
Figure 47. AD9775, Real DAC Output of Complex
Input Signal Near Baseband (Negative Frequencies
Only), Interpolation = 4
؋
, Complex Modulation in AD9775 = –fDAC/4
Figure 49. AD9775, Real DAC Output of Complex
Input Signal Near Baseband (Positive Frequencies
Only), Interpolation = 8
؋
, Complex Modulation in AD9775 = +fDAC/8
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–100
750 760 770 780 790 800 810 820 830 840 850
700 720 740 760 780 800 820 840 860 880 900
FREQUENCY – MHz
FREQUENCY – MHz
Figure 50. AD9775 Complex Output from
Figure 49, Now Quadrature Modulated by
AD8345 (LO = 800 MHz)
Figure 48. AD9775 Complex Output from
Figure 47, Now Quadrature Modulated by
AD8345 (LO = 800 MHz)
–36–
REV. 0
AD9775
APPLYING THE AD9775 OUTPUT CONFIGURATIONS
The following sections illustrate typical output configurations for
the AD9775. Unless otherwise noted, it is assumed that IOUTFS
is set to a nominal 20 mA. For applications requiring optimum
dynamic performance, a differential output configuration is
suggested. A simple differential output may be achieved by con-
verting IOUTA and IOUTB to a voltage output by terminating
them to AGND via equal value resistors. This type of configura-
tion may be useful when driving a differential voltage input
device such as a modulator. If a conversion to a single-ended
signal is desired and the application allows for ac-coupling, an RF
transformer may be useful, or if power gain is required, an op amp
may be used. The transformer configuration provides optimum
high frequency noise and distortion performance. The differen-
tial op amp configuration is suitable for applications requiring
dc-coupling, signal gain, and/or level shifting within the band-
width of the chosen op amp.
DIFFERENTIAL COUPLING USING A TRANSFORMER
An RF transformer can be used to perform a differential-
to-single-ended signal conversion as shown in Figure 52. A
differentially coupled transformer output provides the optimum
distortion performance for output signals whose spectral content
lies within the transformer’s pass band. An RF transformer such
as the Mini-Circuits T1-1T provides excellent rejection of
common-mode distortion (i.e., even-order harmonics) and noise
over a wide frequency range. It also provides electrical isolation
and the ability to deliver twice the power to the load. Trans-
formers with different impedance ratios may also be used for
impedance matching purposes.
MINI-CIRCUITS
T1-T2
I
OUTA
R
DAC
LOAD
I
OUTB
A single-ended output is suitable for applications requiring a
unipolar voltage output. A positive unipolar output voltage will
result if IOUTA and/or IOUTB is connected to a load resistor,
RLOAD, referred to AGND. This configuration is most suitable
for a single-supply system requiring a dc-coupled, ground referred
output voltage. Alternatively, an amplifier could be configured
as an I-V converter, thus converting IOUTA or IOUTB into a nega-
tive unipolar voltage. This configuration provides the best DAC
dc linearity as IOUTA or IOUTB are maintained at ground or vir-
tual ground.
Figure 52. Transformer-Coupled Output Circuit
The center tap on the primary side of the transformer must be
connected to AGND to provide the necessary dc current path
for both IOUTA and IOUTB. The complementary voltages appearing
at IOUTA and IOUTB (i.e., VOUTA and VOUTB) swing symmetrically
around AGND and should be maintained within the specified
output compliance range of the AD9775. A differential resistor,
RDIFF, may be inserted in applications where the output of the
transformer is connected to the load, RLOAD, via a passive recon-
struction filter or cable. RDIFF is determined by the transformer’s
impedance ratio and provides the proper source termination
that results in a low VSWR. Note that approximately half the
UNBUFFERED DIFFERENTIAL OUTPUT, EQUIVALENT
CIRCUIT
In many applications, it may be necessary to understand the
equivalent DAC output circuit. This is especially useful when
designing output filters or when driving inputs with finite input
impedances. Figure 51 illustrates the output of the AD9775 and
the equivalent circuit. A typical application where this information
may be useful is when designing an interface filter between the
AD9775 and Analog Devices’ AD8345 quadrature modulator.
signal power will be dissipated across RDIFF
.
DIFFERENTIAL COUPLING USING AN OP AMP
An op amp can also be used to perform a differential-to-single-
ended conversion as shown in Figure 53. This has the added
benefit of providing signal gain as well. In Figure 53, the AD9775
is configured with two equal load resistors, RLOAD, of 25 Ω. The
differential voltage developed across IOUTA and IOUTB is converted
to a single-ended signal via the differential op amp configura-
tion. An optional capacitor can be installed across IOUTA and
IOUTB, forming a real pole in a low pass filter. The addition of
this capacitor also enhances the op amp’s distortion performance
by preventing the DAC’s fast slewing output from overloading
the input of the op amp.
I
V
+
OUTA
OUT
I
V
–
OUTB
OUT
R
+ R
A
B
500⍀
V
=
B
p-p
SOURCE
A
V
OUT
(DIFFERENTIAL)
I
؋
(R + R ) OUTFS
225⍀
I
OUTA
AD8021
DAC
I
OUTB
Figure 51. DAC Output Equivalent Circuit
C
225⍀
OPT
AVDD
For the typical situation, where IOUTFS = 20 mA and RA and RB
both equal 50 Ω, the equivalent circuit values become:
R
OPT
225⍀
25⍀
25⍀
500⍀
V
R
SOURCE = 2 V p-p
OUT = 100 Ω
Figure 53. Op Amp-Coupled Output Circuit
The common-mode (and second order distortion) rejection of this
configuration is typically determined by the resistor matching.
The op amp used must operate from a dual supply since its
output is approximately 1.0 V. A high speed amplifier, such as
the AD8021, capable of preserving the differential performance
Note that the output impedance of the AD9775 DAC itself is
greater than 100 kΩ and typically has no effect on the impedance
of the equivalent output circuit.
REV. 0
–37–
AD9775
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
of the AD9775 while meeting other system level objectives (i.e.,
cost, power) is recommended. The op amp’s differential gain,
its gain setting resistor values, and full-scale output swing capa-
bilities should all be considered when optimizing this circuit. ROPT
is only necessary if level shifting is required on the op amp out-
put. In Figure 53, AVDD, which is the positive analog supply for
both the AD9775 and the op amp, is also used to level shift the
differential output of the AD9775 to midsupply (i.e., AVDD/2).
INTERFACING THE AD9775 WITH THE AD8345
QUADRATURE MODULATOR
The AD9775 architecture was defined to operate in a transmit
signal chain using an image reject architecture. A quadrature
modulator is also required in this application and should be
designed to meet the output characteristics of the DAC as much
as possible. The AD8345 from Analog Devices meets many of
the requirements for interfacing with the AD9775. As with any
DAC output interface, there are a number of issues that have to
be resolved. Among the major issues are the following.
762.5
782.5
802.5
FREQUENCY – MHz
822.5
842.5
Figure 54. AD9775/AD8345 Synthesizing a Three-
Carrier WCDMA Signal at an LO of 800 MHz
EVALUATION BOARD
DAC Compliance Voltage/Input Common-Mode Range
The dynamic range of the AD9775 is optimal when the DAC
outputs swing between 1.0 V. The input common-mode range
of the AD8345, at 0.7 V, allows optimum dynamic range to be
achieved in both components.
The AD9775 evaluation board allows easy configuration of the
various modes, programmable via the SPI port. Software is
available for programming the SPI port from either Win95® or
Win98®. The evaluation board also contains an AD8345 quadra-
ture modulator and support circuitry that allows the user to
optimally configure the AD9775 in an image reject transmit
signal chain.
Gain/Offset Adjust
The matching of the DAC output to the common-mode input
of the AD8345 allows the two components to be dc-coupled,
with no level shifting necessary. The combined voltage offset of
the two parts can therefore be compensated for via the AD9775
programmable offset adjust. This allows excellent LO cancella-
tion at the AD8345 output. The programmable gain adjust
allows for optimal image rejection as well.
Figures 55 through 58 describe how to configure the evaluation
board in the one and two port input modes with the PLL
enabled and disabled. Refer to Figures 59 through 68, the
schematics, and the layout for the AD9775 evaluation board for
the jumper locations described below. The AD9775 outputs can
be configured for various applications by referring to the follow-
ing instructions.
The AD9775 evaluation board includes an AD8345 and recom-
mended interface (Figures 59 and 60). On the output of the
AD9775, R9 and R10 convert the DAC output current to a
voltage. R16 may be used to do a slight common-mode shift if
necessary. The (now voltage) signal is applied to a low pass
reconstruction filter to reject DAC images. The components
installed on the AD9775 provide a 35 MHz cutoff, but may be
changed to fit the application. A balun (Mini-Circuits ADTL1-12)
is used to cross the ground plane boundary to the AD8345.
Another balun (Mini-Circuits ETC1-1-13) is used to couple
the LO input of the AD8345. The interface requires a low ac
impedance return path from the AD8345, so a single connec-
tion between the AD9775 and AD8345 ground planes is
recommended.
DAC Single-Ended Outputs
Remove transformers T2 and T3. Solder jumper links JP4 or
JP28 to look at the DAC1 outputs. Solder jumper links JP29 or
JP30 to look at the DAC2 outputs. Jumpers 8 and 13–17 should
remain unsoldered. The jumpers JP35–JP38 may be used to
ground one of the DAC outputs while the other is measured
single-ended. Optimum single-ended distortion performance is
typically achieved in this manner. The outputs are taken from
S3 and S4.
DAC Differential Outputs
Transformers T2 and T3 should be in place. Note that the lower
band of operation for these transformers is 300 kHz to 500 kHz.
Jumpers 4, 8, 13–17, and 28–30 should remain unsoldered. The
outputs are taken from S3 and S4.
The performance of the AD9775 and AD8345 in an image reject
transmitter, reconstructing three WCDMA carriers, can be seen
in Figure 54. The LO of the AD8345 in this application is 800 MHz
Using the AD8345
.
Remove transformers T2 and T3. Jumpers JP4 and 28–30 should
remain unsoldered. Jumpers 13–16 should be soldered. The
desired components for the low pass interface filter L6, L7, C55,
and C81 should be in place. The LO drive is connected to the
AD8345 via J10 and the balun T4; and the AD8345 output is
taken from J9.
Image rejection (50 dB) and LO feedthrough (–78 dBFS) have
been optimized with the programmable features of the AD9775.
The average output power of the digital waveform for this test
was set to –15 dBFS to account for the peak-to-average ratio of
the WCDMA signal.
Win95 and Win98 are a registered trademarks of Microsoft Corporation.
–38–
REV. 0
AD9775
LECROY
SIGNAL GENERATOR
PULSE
TRIG
INP
GENERATOR
DATACLK
CLK+/CLK–
INPUT CLOCK
AWG2021
OR
DG2020
40-PIN RIBBON CABLE
DAC1, DB11–DB0
DAC2, DB11–DB0
AD9775
JUMPER CONFIGURATION FOR TWO PORT MODE PLL ON
SOLDERED/IN
UNSOLDERED/OUT
JP1 –
JP2 –
؋
؋
JP3 –
JP5 –
؋
؋
JP6 –
؋
؋
؋
JP12 –
JP24 –
JP25 –
JP26 –
JP27 –
JP31 –
JP32 –
JP33 –
؋
؋
؋
؋
؋
؋
Figure 55. Test Configuration for AD9775 in Two Port Mode with PLL Enabled, Signal Generator
Frequency = Input Data Rate, DAC Output Data Rate = Signal Generator Frequency
؋
Interpolation Rate LECROY
SIGNAL GENERATOR
PULSE
TRIG
INP
GENERATOR
ONEPORTCLK
CLK+/CLK–
INPUT CLOCK
AD9775
AWG2021
OR
DG2020
DAC1, DB11–DB0
DAC2, DB11–DB0
JUMPER CONFIGURATION FOR TWO PORT MODE PLL ON
SOLDERED/IN
UNSOLDERED/OUT
JP1 –
JP2 –
؋
؋
JP3 –
JP5 –
JP6 –
؋
؋
؋
؋
؋
JP12 –
JP24 –
JP25 –
JP26 –
JP27 –
JP31 –
JP32 –
JP33 –
؋
؋
؋
؋
؋
؋
Figure 56. Test Configuration for AD9775 in One Port Mode with PLL Enabled, Signal Generator
Frequency = One-Half Interleaved Input Data Rate, ONEPORTCLK = Interleaved Input Data Rate, DAC Output
Data Rate = Signal Generator Frequency
؋
Interpolation Rate REV. 0
–39–
AD9775
LECROY
SIGNAL GENERATOR
PULSE
TRIG
INP
GENERATOR
DATACLK
CLK+/CLK–
INPUT CLOCK
AWG2021
OR
DG2020
40-PIN RIBBON CABLE
DAC1, DB11–DB0
DAC2, DB11–DB0
AD9775
JUMPER CONFIGURATION FOR TWO PORT MODE PLL OFF
SOLDERED/IN
UNSOLDERED/OUT
JP1 –
JP2 –
؋
؋
JP3 –
JP5 –
؋
؋
JP6 –
؋
؋
؋
JP12 –
JP24 –
JP25 –
JP26 –
JP27 –
JP31 –
JP32 –
JP33 –
؋
؋
؋
؋
؋
؋
Figure 57. Test Configuration for AD9775 in Two Port Mode with PLL Disabled, DAC Output Data Rate = Signal
Generator Frequency, DATACLK = Signal Generator Frequency/Interpolation Rate
LECROY
SIGNAL GENERATOR
PULSE
TRIG
INP
GENERATOR
ONEPORTCLK
CLK+/CLK–
INPUT CLOCK
AD9775
AWG2021
OR
DG2020
DAC1, DB11–DB0
DAC2, DB11–DB0
JUMPER CONFIGURATION FOR TWO PORT MODE PLL OFF
SOLDERED/IN
UNSOLDERED/OUT
JP1 –
JP2 –
؋
؋
JP3 –
JP5 –
JP6 –
؋
؋
؋
؋
؋
JP12 –
JP24 –
JP25 –
JP26 –
JP27 –
JP31 –
JP32 –
JP33 –
؋
؋
؋
؋
؋
؋
Figure 58. Test Configuration for AD9775 in One Port Mode with PLL Disabled, DAC Output Data Rate =
Signal Generator Frequency, ONEPORTCLK = Interleaved Input Data Rate = 2× Signal Generator
Frequency/Interpolation Rate
–40–
REV. 0
AD9775
O1P
O1N
O2P
O2N
C72
10F VDDM
10V
C54
DNP
C55
DNP
C35
10F
L5
DNP
L4
DNP
L7
DNP
L6
DNP
C75
0.1F
C78
0.1F
C73
DNP
C81
DNP
T6
ADTL1-12
T5
ADTL1-12
3
1
4
6
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
4
6
3
1
IBBP
S
S
P
P
R36
51⍀
R35
51⍀
J20
R33
51⍀
J19
R32
51⍀
C77
100pF
C78
0.1F
C79
DNP
R37
DNP
R34
DNP
C80
DNP
3
S
1
5
T4
ETC1-1-13
VDDMIN
R26
1k⍀
C74
100pF
P
JP18
4
R30
DNP
R28
R23
0⍀
LOCAL OSC INPUT
DGND; 3, 4, 5
MODULATED OUTPUT
DGND; 3, 4, 5
0⍀
J10
J10
J21 J7
POWER INPUT FILTERS
L8 FERRITE
VDDMIN
W11
VDDM
C28
22F
16V
C32
0.1F
W12
TP2
RED
L3 FERRITE
J9
DVDD_IN
AGND
J8
J5
DVDD
C65
22F
16V
C66
22F
16V
C67
0.1F
TP3
BLK
TP4
RED
J10
L2 FERRITE
AVDD_IN
AGND
J4
J6
AVDD
C64
22F
16V
C61
22F
16V
C68
0.1F
TP5
BLK
TP6
RED
J11
L1 FERRITE
CLKVDD_IN
AGND
J3
J7
CLKVDD
C63
22F
16V
C62
22F
16V
C69
0.1F
TP7
BLK
Figure 59. AD8345 Circuitry on AD9775 Evaluation Board
REV. 0
–41–
AD9775
Figure 60. AD9775 Clock, Power Supplies, and Output Circuitry
–42–
REV. 0
AD9775
Figure 61. AD9775 Evaluation Board Input (A Channel) and Clock Buffer Circuitry
–43–
REV. 0
AD9775
DATA-B
RP12
50⍀
RP9
DNP
RCON
1
RCON
1
R1 R2 R3 R4 R5 R6 R7 R8 R9
2 3 4 6 7 8 9 10
R1 R1 R1 R1 R1 R1 R1 R1 R1
2 3 4 5 8 10
5
6
7
9
1
2
4
6
8
1
16
RP3, 22⍀
15
RP3, 22⍀
14
RP3, 22⍀
13
RP3, 22⍀
12
RP3, 22⍀
11
RP3, 22⍀
10
RP3, 22⍀
BD15
3
2
BD14
BD13
BD12
BD11
BD10
BD09
BD08
BD07
BD06
BD05
5
3
7
4
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
5
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
6
7
8
9
RP4, 22⍀
16
RP4, 22⍀
15
RP4, 22⍀
14
RP4, 22⍀
13
RP4, 22⍀
12
RP4, 22⍀
11
RP4, 22⍀
10
RP4, 22⍀
1
2
3
4
BD04
BD03
5
6
BD02
BD01
BD00
7
8
9
RP4, 22⍀
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
RP11
50⍀
RP10
R1 R2 R3 R4 R5 R6 R7 R8 R9
R1 R2 R3 R4 R5 R6 R7 R8 R9
RCON
RCON
DNP
DVDD
DVDD
C43
C44
C50
0.1F
C51
0.1F
4.7F
4.7F
RIBBON
J2
6.3V
6.3V
R50
9k⍀
1
2
12
13
U5
U5
AGND; 7
DVDD; 14
AGND; 7
DVDD; 14
74AC14
74AC14
SPI PORT
P1
R48
9k⍀
4
3
10
11
U5
U5
1
2
3
4
5
6
AGND; 7
DVDD; 14
AGND; 7
DVDD; 14
74AC14
74AC14
R45
9k⍀
6
5
8
9
SPCSB
U5
U5
AGND; 7
DVDD; 14
AGND; 7
DVDD; 14
74AC14
74AC14
SPCLK
SPSDI
2
1
12
13
SPSDO
U6
U6
AGND; 7
DVDD; 14
AGND; 7
DVDD; 14
74AC14
74AC14
4
10
3
11
U6
U6
AGND; 7
DVDD; 14
AGND; 7
DVDD; 14
74AC14
74AC14
6
8
5
9
U6
U6
AGND; 7
DVDD; 14
AGND; 7
DVDD; 14
74AC14
74AC14
Figure 62. AD9775 Evaluation Board Input (B Channel) and SPI Port Circuitry
–44–
REV. 0
AD9775
Figure 63. AD9775 Evaluation Board Components, Top Side
Figure 64. AD9775 Evaluation Board Components, Bottom Side
REV. 0
–45–
AD9775
Figure 65. AD9775 Evaluation Board Layout, Layer One (Top)
Figure 66. AD9775 Evaluation Board Layout, Layer Two (Ground Plane)
–46–
REV. 0
AD9775
Figure 67. AD9775 Evaluation Board Layout, Layer Three (Power Plane)
Figure 68. AD9775 Evaluation Board Layout, Layer Four (Bottom)
REV. 0
–47–
AD9775
OUTLINE DIMENSIONS
80-Lead, Thermally Enhanced, Thin Plastic Quad Flatpack [TQFP]
(SV-80)
Dimensions shown in millimeters and (inches)
14.00 (0.5512) SQ
12.00 (0.4724) SQ
1.20 (0.0472)
MAX
0.75 (0.0295)
0.60 (0.0236)
0.45 (0.0177)
80
80
61
61
60
60
1
1
SEATING
PLANE
PIN 1
TOP VIEW
(PINS DOWN)
BOTTOM
VIEW
6.00 (0.2362) SQ
20
41
20
41
COPLANARITY
0.15 (0.0059)
0.05 (0.0020)
21
40
40
21
1.05 (0.0413)
1.00 (0.0394)
0.95 (0.0374)
0.20 (0.0079)
0.09 (0.0035)
GAGE PLANE
0.25 (0.0098)
0.27 (0.0106)
0.22 (0.0087)
0.17 (0.0067)
7؇
3.5؇
0؇
0.50 (0.0197)
BSC
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
COMPLIANT TO JEDEC STANDARDS MO-026-ADD
AN APPLICATION NOTE DETAILING THE THERMALLY ENHANCED TQFP
CAN BE FOUND AT;
www.amkor.com/products/notes_papers/MLF_Appnote_0301.pdf
REV. 0
–48–
相关型号:
AD9775BSV
PARALLEL, WORD INPUT LOADING, 0.011 us SETTLING TIME, 14-BIT DAC, PQFP80, PLASTIC, MO-026-ADD-HD, TQFP-80
ROCHESTER
AD9775BSVRL
IC PARALLEL, WORD INPUT LOADING, 0.011 us SETTLING TIME, 14-BIT DAC, PQFP80, PLASTIC, MO-026-ADD-HD, TQFP-80, Digital to Analog Converter
ADI
AD9775BSVZ
PARALLEL, WORD INPUT LOADING, 0.011 us SETTLING TIME, 14-BIT DAC, PQFP80, LEAD FREE, PLASTIC, MO-026-ADD-HD, TQFP-80
ROCHESTER
©2020 ICPDF网 联系我们和版权申明