AD1856RZ-K-REEL7 [ADI]
16-Bit PCM Audio D/A Converter;
| 型号： | AD1856RZ-K-REEL7 |
| 厂家： | 
ADI |
| 描述： | 16-Bit PCM Audio D/A Converter PC 光电二极管 转换器 |
| 文件： | 总16页 (文件大小：302K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
16-Bit PCM Audio DAC
Data Sheet
AD1856
FEATURES
FUNCTIONAL BLOCK DIAGRAM
R
F
0.0025% THD
Fast settling permits 2×, 4×, and 8× oversampling
3 ꢀ output
16-BIT
DAC
REFERENCE
I
OUT
Optional trim allows superlinear performance
5 ꢀ to 12 ꢀ operation
16-lead plastic SOIC package
Serial input
AUDIO
OUTPUT
16-BIT INPUT LATCH
16-BIT SERIAL-TO-PARALLEL
CONVERSION
APPLICATIONS
CLK
LE
DATA
Compact disc players
Figure 1.
Digital audio amplifiers
DAT recorders and players
Synthesizers and keyboards
GENERAL DESCRIPTION
The AD1856 is a monolithic, 16-bit pulse code modulation (PCM)
audio DAC. The device provides a voltage output amplifier, 16-bit
DAC, 16-bit serial-to-parallel input register, and voltage reference.
The digital portion of the AD1856 is fabricated with CMOS logic
elements that are provided by the Analog Devices, Inc., BiMOS II
process. The analog portion of the AD1856 is fabricated with
bipolar and MOS devices, as well as thin film resistors.
The AD1856 can operate with ±5 ꢀ to ±12 ꢀ power supplies,
making it suitable for both the portable and home-use markets.
The digital supplies, +ꢀL and −ꢀL, can be separated from the
analog supplies, +ꢀS and −ꢀS, for reduced digital crosstalk.
Separate analog and digital ground pins are also provided.
Power dissipation is 110 mW (typical) with ±5 ꢀ supplies and
1±5 mW (typical) when ±12 ꢀ supplies are used.
This combination of circuit elements, as well as careful design and
layout techniques, results in high performance audio playback.
Laser trimming of the linearity error affords extremely low total
harmonic distortion. An optional linearity trim pin is provided
to allow residual differential linearity error at midscale to be
eliminated. This feature is particularly valuable for low distortion
reconstructions of low amplitude signals. Output glitch is also
small, contributing to the overall high level of performance. The
output amplifier achieves fast settling and high slew rates, providing
a full ±± ꢀ signal at load currents of up to ±8 mA. The output
amplifier is short-circuit protected and can withstand indefinite
shorts to ground.
The AD1856 is packaged in a 16-lead plastic SOIC package
and incorporates the industry-standard pinout. Operation is
guaranteed over the temperature range of −25°C to +70°C and
over the voltage supply range of ±4.75 ꢀ to ±1±.2 ꢀ.
PRODUCT HIGHLIGHTS
1. Total harmonic distortion is 100% tested.
2. MSB trim feature allows superlinear operation.
±. The AD1856 operates with ±5 ꢀ to ±12 ꢀ supplies.
4. Serial interface is compatible with digital filter chips.
5. 1.5 μs settling time permits 2×, 4×, and 8× oversampling.
6. No external components are required.
7. 96 dB dynamic range.
8. ±± ꢀ or ±8 mA output capability.
9. 16-bit resolution.
10. Twos complement serial input words.
The serial input interface consists of the clock, data, and latch
enable pins. The serial twos complement data-word is clocked
into the DAC, MSB first, by the external data clock. The latch
enable signal transfers the input word from the internal serial input
register to the parallel DAC input register. The input clock can
support a 10 MHz clock rate. The serial input port is compatible
with popular digital filter chips used in consumer audio products.
These filters operate at oversampling rates of 2×, 4×, and 8× the
sampling frequency.
11. Low cost.
12. 16-lead plastic SOIC package.
Rev. C
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©1988–2013 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
AD1856
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Power Supplies and Decoupling..................................................9
Total Harmonic Distortion ..........................................................9
Optional MSB Adjustment........................................................ 10
Digital Circuit Considerations...................................................... 11
Input Data ................................................................................... 11
Applications of the AD1856 PCM Audio DAC.......................... 12
One DAC per System................................................................. 12
One DAC per Channel .............................................................. 12
Two DACs per Channel (Four-DAC System) ........................ 13
Digital Filtering and Oversampling ............................................. 14
Applications....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description ......................................................................... 1
Product Highlights ........................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Absolute Maximum Ratings............................................................ 5
ESD Caution.................................................................................. 5
Pin Configuration and Function Descriptions............................. 6
Terminology ...................................................................................... 7
Theory of Operation ........................................................................ 8
Analog Circuit Considerations ....................................................... 9
Grounding Recommendations ................................................... 9
Achieving 8× fS Oversampling with Two AD1856 Devices
and the Yamaha YM3414 .......................................................... 14
Outline Dimensions....................................................................... 15
Ordering Guide .......................................................................... 15
REVISION HISTORY
2/13—Rev. B to Rev. C
Changes to Table 2.............................................................................5
Changes to Figure 2 and Table 3......................................................6
Deleted Figure 14 and Dual DAC, 4× fS Oversampling
Architecture Section..........................................................................7
Changes to Grounding Recommendations Section,
Updated Format..................................................................Universal
Deleted 16-Lead DIP (N) Package ...................................Universal
Reorganized Layout............................................................Universal
Changes to Features Section, General Description
Section, and Product Highlights Section ...................................... 1
Changes to Total Harmonic Distortion Parameter
and Power Supply Parameter, Table 1............................................ 3
Changes to Power Dissipation Parameter, Table 1....................... 4
Deleted Figure 1; Renumbered Sequentially................................. 4
Power Supplies and Decoupling Section, and Figure 3................9
Changes to Input Data Section..................................................... 11
Changes to Digital Filtering and Oversampling Section .......... 14
Updated Outline Dimensions....................................................... 15
Changes to Ordering Guide.......................................................... 15
Rev. C | Page 2 of 16
Data Sheet
AD1856
SPECIFICATIONS
Typical values at TA = 25°C, VL = 5 V, and VS = 5 V, unless otherwise noted.
Table 1.
Parameter
Test Conditions/Comments
Min
Typ
Max
Unit
RESOLUTION1
16
Bits
DIGITAL INPUTS
Input Voltage High, VIH
Input Voltage Low, VIL
2.4
0.8
+VL
V
V
µA
µA
MHz
0
1
Input Current High, IIH
VIH = +VL
VIL = 0.4 V
1.0
−10
1
Input Current Low, IIL
Clock Input Frequency1
10
ACCURACY
Gain Error
2.0
30
0.001
%
mV
% of FSR
µV
Bipolar Zero Error
Differential Linearity Error
Noise at Bipolar Zero
TOTAL HARMONIC DISTORTION
0 dB
RMS, 20 Hz to 20 kHz
990.5 Hz
AD1856RZ-K
AD1856RZ
AD1856RZ-K
AD1856RZ
AD1856RZ-K
AD1856RZ
6
0.002
0.002
0.018
0.018
1.8
0.00251
0.0081
0.0201
0.0401
2.01
%
%
%
%
%
%
−20 dB
−60 dB
1.8
4.01
MONOTONICITY
DRIFT
15
Bits
0°C to 70°C
Total Drift
25
4
ppm of FSR/°C
ppm of FSR/°C
Bipolar Zero Drift
SETTLING TIME
Voltage Output
To 0.006% of FSR
6 V step
1 LSB step
1.5
1.0
9
350
350
µs
µs
V/µs
ns
ns
Slew Rate
Current Output
1 mA step, 10 Ω to 100 Ω load
1 kΩ load
WARM-UP TIME
1
Minute
OUTPUT
Voltage Output Configuration
Bipolar Range
3
V
Output Current
8
mA
Ω
Output Impedance
Short-Circuit Duration
Current Output Configuration
Bipolar Range ( 30%)
Output Impedance ( 30%)
POWER SUPPLY
0.1
Indefinite to ground
1.0
1.7
mA
kΩ
Voltage, +VL and +VS
Voltage, −VL and −VS
Current, +I
+VS ≥ +VL for operation
−VL ≥ −VS for operation
+VL and +VS = 5 V, 10 MHz clock
+VL and +VS = 12 V, 10 MHz clock
−VL and −VS = −5 V, 10 MHz clock
−VL and −VS = −12 V, 10 MHz clock
4.75
−13.2
5
−5
10
12
−12
−15
13.2
−4.75
151
V
V
mA
mA
mA
mA
Current, −I
−151
Rev. C | Page 3 of 16
AD1856
Data Sheet
Parameter
Test Conditions/Comments
10 MHz clock
VS and VL = 5 V
Min
Typ
Max
Unit
POWER DISSIPATION
110
135
1501
mW
mW
VS and VL = 12 V
TEMPERATURE RANGE
Specification
Operational
0
−25
−60
+70
+70
+100
°C
°C
°C
Storage
1 Tested on all production units at final test.
Rev. C | Page 4 of 16
Data Sheet
AD1856
ABSOLUTE MAXIMUM RATINGS
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Table 2.
Parameter
Rating
+VL to DGND
+VS to AGND
−VL to DGND
−VS to AGND
Digital Inputs to DGND
AGND to DGND
Short-Circuit Protection
Soldering, 10 sec
Storage Temperature Range
0 V to 13.2 V
0 V to 13.2 V
−13.2 V to 0 V
−13.2 V to 0 V
−0.3 V to +VL
0.3 V
Indefinite short to ground
300°C
−60°C to +100°C
ESD CAUTION
Rev. C | Page 5 of 16
AD1856
Data Sheet
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
16-BIT
LATCH
16-BIT
DAC
1
2
3
4
5
6
7
8
16
15
14
13
–V
+V
S
S
DGND
+V
TRIM
SERIAL
INPUT
REGISTER
MSB ADJ
L
NC
CLK
LE
I
I
OUT
OUT
12 AGND
CONTROL
LOGIC
SJ
11
10
9
DATA
R
F
–V
L
V
OUT
AD1856
NC = NO CONNECT
Figure 2. Pin Configuration
Table 3. Pin Function Descriptions
Pin No.
Mnemonic
Description
1
2
3
4
−VS
DGND
+VL
Analog Power Supply, Negative
Digital Ground
Logic Power Supply, Positive
No Connection
NC
5
CLK
Data Clock Input
6
LE
Latch Enable Input
7
8
9
DATA
−VL
VOUT
Serial Data Input
Logic Power Supply, Negative
Voltage Output
10
11
12
13
14
15
16
RF
SJ
Feedback Resistor
Summing Junction
Analog Ground
Current Output
MSB Adjustment Terminal
MSB Trimming Potentiometer Terminal
Analog Power Supply, Positive
AGND
IOUT
MSB ADJ
TRIM
+VS
Rev. C | Page 6 of 16
Data Sheet
AD1856
TERMINOLOGY
Total Harmonic Distortion
The theoretical dynamic range of an n-bit converter is approx-
imately (6 × n) dB. In the case of the 16-bit AD1856, that is
96 dB. The actual dynamic range of a converter is less than the
theoretical value due to limitations imposed by noise, quantiza-
tion error, and other errors.
Total harmonic distortion (THD) is defined as the ratio of the
square root of the sum of the squares of the harmonic values to
the value of the fundamental input frequency. THD is expressed
in percent (%) or decibels (dB).
THD is a measure of the magnitude and distribution of linearity
error and differential linearity error. The distribution of these
errors may be different, depending on the amplitude of the output
signal. Therefore, to be most useful, THD should be specified for
both large and small signal amplitudes.
Bipolar Zero Error
Bipolar zero error is the deviation in the actual analog output
from the ideal output (0 V) when the twos complement input
code representing half scale (all 0s) is loaded into the input
register.
Settling Time
Differential Linearity Error
Settling time is the time required for the output to reach and
remain within a specified error band about its final value, mea-
sured from the digital input transition. Settling time is the primary
measure of dynamic performance.
Differential linearity error is the measure of the variation in
analog value, normalized to full scale, associated with a 1 LSB
change in the digital input. Monotonic behavior requires that
the differential linearity error not exceed 1 LSB in the negative
direction.
Dynamic Range
The dynamic range specification indicates the ratio of the small-
est signal that the converter can resolve to the largest signal it is
able to produce. As a ratio, it is usually expressed in decibels (dB).
Monotonicity
A digital-to-analog converter is monotonic if the output either
increases or remains constant as the digital input increases.
Rev. C | Page 7 of 16
AD1856
Data Sheet
THEORY OF OPERATION
The AD1856 is a complete, monolithic, 16-bit PCM audio DAC.
No additional external components are required for operation.
As shown in the block diagram in Figure 1, each chip contains
a voltage reference, an output amplifier, a 16-bit DAC, a 16-bit
input latch, and a 16-bit serial-to-parallel input register.
The resistors that form the ladder structure are fabricated with
silicon-chromium thin film. Laser trimming of these resistors
further reduces linearity error, resulting in low output distortion.
The output amplifier uses both MOS and bipolar devices to
produce low offset, high slew rate, and optimum settling time.
When combined with the on-board feedback resistor, the output
op amp can convert the output current of the AD1856 to a
voltage output.
The voltage reference consists of a band gap circuit and buffer
amplifier. This circuitry produces an output voltage that is stable
over time and temperature changes.
The 16-bit digital-to-analog converter uses a combination of a
segmented decoder and R-2R architectures to achieve consistent
linearity and differential linearity.
Rev. C | Page 8 of 16
Data Sheet
AD1856
ANALOG CIRCUIT CONSIDERATIONS
+5V
16
GROUNDING RECOMMENDATIONS
+V
+V
S
L
The AD1856 has two ground pins, designated analog and digital
ground (AGND and DGND). The analog ground pin is the high
quality ground reference point for the analog portion of the
device. The digital ground pin returns ground current from the
digital logic portions of the AD1856 circuitry. Both pins should
be connected directly to a single solid ground plane, and the
components should be placed around the AD1856 so that analog
and digital return currents do not cross each other. A single solid
ground plane with good parts placement and trace routing yields
the quietest design with the best signal integrity and EMI/EMC
specifications.
3
AD1856
2
8
1
12
DGND
–V
–V
AGND
L
S
GROUND
–5V
Figure 3. Alternate Recommended Schematic
Given that these two supplies are within the range of 5 V to
12 V, they can be used to power the AD1856. In this case, the
positive logic and positive analog supplies can both be connected
to the single positive supply. The negative logic and negative analog
supplies can both be connected to the single negative supply.
Performance benefits from a measure of isolation between the
supplies, introduced by using simple low-pass filters in the
individual power supply leads.
POWER SUPPLIES AND DECOUPLING
The AD1856 has four power supply input pins. +VS and −VS
provide the supply voltages to operate the linear portions of the
DAC, including the voltage reference, output amplifier, and
control amplifier. The +VS and −VS supplies are designed to
operate from 5 V to 12 V.
As with most linear circuits, changes in the power supplies affect
the output of the DAC. Analog Devices recommends that well-
regulated power supplies with less than 1% ripple be incorporated
into the design of any system using these devices.
The +VL and −VL pins supply power to the digital portions of
the chip, including the input shift register and the input latching
circuitry. The +VL and −VL supplies are also designed to operate
from 5 V to 12 V, subject only to the limitation that +VL cannot
be more positive than +VS, and −VL cannot be more negative
than −VS.
TOTAL HARMONIC DISTORTION
The THD figure of an audio DAC represents the amount of
undesirable signal produced during reconstruction and play-
back of an audio waveform. The THD specification, therefore,
provides a direct method for classifying and choosing an audio
DAC for a desired level of performance.
Decoupling capacitors should be used on all power supply pins.
Furthermore, good engineering practice suggests that these
capacitors be placed as close as possible to the package pins. The
decoupling for both the bipolar logic supply, VL, and the bipolar
analog supply, VS, should be returned to the closest ground pins.
Analog Devices tests and grades all AD1856 devices on the
basis of THD performance. A block diagram of the test setup
is shown in Figure 4. In this test setup, a digital data stream,
representing a 0 dB, −20 dB, or −60 dB sine wave, is sent to the
device under test. The frequency of this waveform is 990.5 Hz.
Input data is sent to the AD1856 at a 4× fS rate (176.4 kHz). The
AD1856 under test produces an analog output signal with the
on-board op amp.
The use of four separate power supplies reduces feedthrough
from the digital portion of the system to the linear portions of
the system, thus contributing to good performance. However,
four separate voltage supplies are not necessary for good circuit
performance. For example, Figure 3 illustrates a system where
only a single positive and a single negative supply are available.
23 CYCLES
4× fS
DATA
AD1856
RATE
±3V
16-BIT
DATA
DIGITAL
WAVEFORM
GENERATOR
V
OUT
LE
CLK
990.5Hz
NOTCH
FILTER
30kHz
LOW-PASS
FILTER
0
1
1
0
1
0
1
0
1
1
0
OUTPUT
1
1
.
1
.
0
.
1
.
0
.
1
.
4096 PT.
FFT
ANALYZER
DIGITIZER
.
.
.
.
.
.
.
.
.
.
.
.
1
1
0
1
0
0
0
1
1
0
0
1
1
1
1
0
1
0
4096
SAMPLES
Figure 4. Block Diagram of Distortion Test Circuit
Rev. C | Page 9 of 16
AD1856
Data Sheet
0.100
0.050
The automatic test equipment digitizes 4096 samples of the
output test waveform, incorporating 23 complete cycles of the
sine wave. A 4096-point FFT is performed on the results of the
test. Based on the first nine harmonics of the fundamental
990.5 Hz output wave, the total harmonic distortion of the
device is calculated. Neither a deglitcher nor an MSB trim is
used during the THD test.
0.020
0.010
0.005
–20dB
The circuit design, layout, and manufacturing techniques used
in the production of the AD1856 result in excellent THD perfor-
mance. Figure 5 shows the typical unadjusted THD performance
of the AD1856 for various amplitudes of a 1 kHz output signal.
As shown in Figure 5, the AD1856 offers excellent performance,
even at amplitudes as low as −60 dB. Figure 6 shows the typical
THD vs. frequency performance.
FULL SCALE
0.002
0.001
1
100
1k
FREQUENCY (Hz)
10k
Figure 6. Typical THD vs. Frequency
10.0
OPTIONAL MSB ADJUSTMENT
Use of an optional adjustment circuit allows residual differential
linearity errors around midscale to be eliminated. These errors
are especially important when low amplitude signals are being
reproduced. In these cases, as the signal amplitude decreases,
the ratio of the midscale differential linearity error to the signal
amplitude increases and THD increases.
1.0
0.1
16 BITS
Therefore, for best performance at low output levels, the optional
MSB adjustment circuitry shown in Figure 7 can be used. This
circuit allows the differential linearity error at midscale to be
zeroed out. However, no adjustments are required to meet data
sheet specifications.
0.01
0.001
–60
–50
–40
–30
–20
–10
0
10
AMPLITUDE (dB)
470kΩ
100kΩ
200kΩ
TRIM
–V
S
15
14
1
Figure 5. Typical Unadjusted THD vs. Amplitude
MSB ADJ
Figure 7. Optional MSB Adjustment Circuit
Rev. C | Page 10 of 16
Data Sheet
AD1856
DIGITAL CIRCUIT CONSIDERATIONS
Figure 9 provides the specific timing requirements that must be
met for the data transfer to be accomplished properly.
INPUT DATA
Data is transmitted to the AD1856 in a bit stream composed
of 16-bit words with a serial, MSB first format. Three signals
must be present to achieve proper operation: the data, clock,
and latch enable signals. Input data bits are clocked into the
input register on the rising edge of the clock signal. The LSB is
clocked in on the 16th clock pulse. When all data bits are loaded,
a low-going latch enable pulse updates the DAC input. Figure 8
illustrates the general signal requirements for data transfer for
the AD1856.
The input pins of the AD1856 are both TTL and 5 V CMOS
compatible, independent of the power supply voltages used.
The input requirements illustrated in Figure 8 and Figure 9
are compatible with the data outputs provided by popular DSP
filter chips used in digital audio playback systems. The AD1856
input clock can run at a 10 MHz rate. This clock rate allows data
transfer rates for 2×, 4×, or 8× oversampling reconstruction. The
Applications of the AD1856 PCM Audio DAC section provides
additional guidelines for using the AD1856 with various DSP
filter chips.
CLK
M
S
B
L
S
B
DATA
LE
Figure 8. Signal Requirements of the AD1856
>100ns
>30ns >30ns
CLK
>15ns
>60ns
>40ns
>40ns
LATCH
ENABLE (LE)
>50ns
INTERNAL DAC INPUT REGISTER
UPDATED WITH 16 MOST RECENT BITS
>15ns >15ns
MSB
1ST BIT
LSB
2ND BIT
NEXT
WORD
DATA
16TH BIT
BITS CLOCKED INTO
SHIFT REGISTER
Figure 9. Timing Relationships of Input Signals
Rev. C | Page 11 of 16
AD1856
Data Sheet
APPLICATIONS OF THE AD1856 PCM AUDIO DAC
The AD1856 is a versatile digital-to-analog converter designed
for applications in consumer digital audio equipment. Portable,
car, and home compact disc players, digital audio amplifiers, and
DAT systems can all use the AD1856. Popular circuit architectures
in these systems include stereo playback sections featuring one
DAC per system, one DAC per audio channel (left/right), or even
multiple DACs per channel. Furthermore, these architectures use
different output reconstruction rates to accomplish these functions,
including reproduction at the sample rate (1 × fS), at twice the
sample rate (2 × fS), at four times the sample rate (4 × fS), and
even at eight times the sample rate (8 × fS). For CD applications,
fS is 44.1 kHz; for DAT applications, fS is 48 kHz.
The architecture illustrated in Figure 10 is suitable for low-end
home or portable systems. However, its usefulness in mid-quality
or high-quality digital audio reproduction is limited by the phase
delay that is introduced in the multiplexed output. This phase delay
is due to the fact that the information contained in the input bit
stream represents left and right channel audio sampled simulta-
neously but reconstructed alternately. One solution to this problem
is to incorporate a third, noninverting SHA to delay the output
of one channel so that it can catch up to the other channel. This
solution eliminates the phase shift by restoring simultaneous
reproduction. This solution is illustrated in Figure 12.
SAMPLE
LEFT
LOW-
PASS
LEFT
OUTPUT
SHA
SHA
ONE DAC PER SYSTEM
FILTER
Figure 10 shows a circuit using one AD1856 per system to repro-
duce both stereo channels of a typical first-generation digital
audio system. The input data is fed to the AD1856 in a format
that alternates between left channel data and right channel data.
The output of the AD1856 is switched between the left channel
and right channel output sample-and-hold amplifiers (SHAs).
The SHAs demultiplex and deglitch the output of the AD1856.
The timing diagram for the control signals for this circuit is
shown in Figure 11.
AD1856
DATA
V
OUT
CLK
LE
LOW-
PASS
FILTER
RIGHT
OUTPUT
SHA
SAMPLE
RIGHT
Figure 12. Third SHA Eliminates Phase Delay
ONE DAC PER CHANNEL
Another approach used to eliminate phase delay between left and
right channels uses one DAC per channel. In this architecture, the
input data bit streams for the left channel and the right channel
are simultaneously sent and latched into each DAC. This second-
generation approach, shown in Figure 13, is suitable for higher
performance digital audio playback units.
LOW-
LEFT
PASS
OUTPUT
SAMPLE
LEFT
FILTER
1/2
AD712
AD1856
DATA
V
OUT
CLK
LE
AD1856
DATA
CLK
LE
LEFT
DATA
V
LOW-
PASS
FILTER
OUT
RIGHT
OUTPUT
SAMPLE
RIGHT
1/2
AD712
LOW-
PASS
FILTER
LEFT
OUTPUT
Figure 10. AD1856 in a One DAC per System Architecture
1/2
AD712
AD1856
DATA
CLK
LE
RIGHT
DATA
V
OUT
CLK
LOW-
PASS
FILTER
RIGHT
OUTPUT
1/2
AD712
DATA
Figure 13. One DAC per Channel Architecture
LEFT WORD
RIGHT WORD
LE
1.5µs MIN
1.5µs MIN
DAC
OUT
SAMPLE
RIGHT
SAMPLE
LEFT
Figure 11. Control Signals for One DAC Circuit
Rev. C | Page 12 of 16
Data Sheet
AD1856
AD1856
TWO DACs PER CHANNEL (FOUR-DAC SYSTEM)
DATA
V
V
OUT
CLK
LE
Another architecture uses two DACs per channel. In this
scheme, shown in Figure 14, each DAC reproduces one half of
the output waveform. The advantage obtained is that midscale
differential linearity error no longer affects the zero-crossing
points of the waveforms. These effects are shifted to the points
where the output waveform crosses 3/4 full scale. The result
is that THD performance for low amplitude signals is greatly
improved. Not shown in Figure 14 is a VLSI circuit, which is
required to separate the incoming data into the appropriate
form required by each DAC.
LOW-
PASS
FILTER
LEFT
OUTPUT
SHA
AD1856
DATA
CLK
LE
1/2
OUT
AD712
AD1856
DATA
CLK
LE
V
V
OUT
LOW-
PASS
FILTER
RIGHT
OUTPUT
SHA
AD1856
DATA
CLK
LE
1/2
OUT
AD712
Figure 14. Two DACs per Channel Eliminate Midscale Distortion
from the Zero-Crossing Points
Rev. C | Page 13 of 16
AD1856
Data Sheet
DIGITAL FILTERING AND OVERSAMPLING
Oversampling is a term that refers to playback techniques in
which the reconstruction frequency used is an integral (2 or
more) multiple of the original quantized data rate. For example,
in compact disc stereo digital audio playback units, the original
quantized data sample rate is 44.1 kHz. Popular oversampling
rates are 2× fS or 4× fS, yielding reconstruction rates of 88.2 kHz
and 176.4 kHz, respectively.
Oversampling techniques require that the serial input data
stream run at the same integral multiple of the original data rate.
Therefore, although the constraints on the output low-pass filter
are eased, the constraints on the serial digital input port and the
settling time of the output stage are not.
The actual oversampling operation takes place in the digital filter
chip, which is located upstream from the DAC. The digital filter
accepts data from the media and adds the additional reconstruction
points according to the algorithm and coefficients stored in the
filter chip. Because the digital filters actually interpolate these
additional reconstruction points, they are called interpolation
filters.
Oversampling is used to ease the performance constraints of
the low-pass filters that usually follow the reconstruction DAC.
In any signal reconstructed from sampled data, undesired
frequency components are introduced in the output spectrum;
these components are centered at the reconstruction frequency.
When a 44.1 kHz reconstruction frequency is used, the actual
frequency band of interest is 20 Hz to 20 kHz. However, a
band of undesired image frequency components extends from
approximately 24 kHz to 44.1 kHz; there is additional undesired
component energy between 44.1 kHz and 64 kHz. These undesired
components must be removed with a low-pass filter of very high
order. First-generation digital audio systems often use low-pass
filters of 9, 11, and even 13 poles. Linear implementations of these
filters are expensive, difficult to manufacture, and can produce
distortion due to varying group delay characteristics.
ACHIEVING 8× fS OVERSAMPLING WITH TWO
AD1856 DEVICES AND THE YAMAHA YM3414
Figure 15 illustrates the combination of a Yamaha YM3414
digital filter chip and two AD1856 audio DACs. In this scheme,
the use of a 16.9344 MHz clock allows an 8× oversampling rate
for extremely high performance. In addition, a lower order low-
pass filter can be used without sacrificing performance. The DAC
input data is simultaneously transmitted to the input registers of
the DACs through dedicated left and right channel output pins on
the YM3414. Optional sample-and-hold signals are also provided.
When a 2× reconstruction frequency (88.2 kHz) is used, the
lowest undesired frequency components extend down to approx-
imately 68 kHz. A 4× rate (176.4 kHz) has undesired components
extending down to approximately 156 kHz. The filter response
required to remove these frequency components can be less steep.
This means that a lower order filter can be used, resulting in less
distortion at lower cost. Linear filters with three or five poles are
adequate and are quite common in digital audio products that use
oversampling techniques.
16.9344MHz
+5V
LOW-
PASS
FILTER
CLK
LE
DATA
LEFT
OUTPUT
V
OUT
TD
WCO
DLO
BCO
DRO
YM3414
SHR SHL
AD1856
DATA
LE
CLK
LOW-
PASS
FILTER
RIGHT
OUTPUT
V
OUT
OPTIONAL
DEGLITCH
SIGNALS
AD1856
Figure 15. Yamaha YM3414 and AD1856 Interface
Rev. C | Page 14 of 16
Data Sheet
AD1856
OUTLINE DIMENSIONS
10.50 (0.4134)
10.10 (0.3976)
16
1
9
8
7.60 (0.2992)
7.40 (0.2913)
10.65 (0.4193)
10.00 (0.3937)
0.75 (0.0295)
0.25 (0.0098)
1.27 (0.0500)
BSC
45°
2.65 (0.1043)
2.35 (0.0925)
0.30 (0.0118)
0.10 (0.0039)
8°
0°
COPLANARITY
0.10
SEATING
PLANE
0.51 (0.0201)
0.31 (0.0122)
1.27 (0.0500)
0.40 (0.0157)
0.33 (0.0130)
0.20 (0.0079)
COMPLIANT TO JEDEC STANDARDS MS-013-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 16. 16-Lead Standard Small Outline Package [SOIC_W]
Wide Body
(RW-16)
Dimensions shown in millimeters and (inches)
ORDERING GUIDE
Model1
Temperature Range
−25°C to +70°C
−25°C to +70°C
−25°C to +70°C
−25°C to +70°C
−25°C to +70°C
THD at Full-Scale Output
0.008%
0.008%
0.008%
0.0025%
Package Description
16-Lead SOIC_W
16-Lead SOIC_W
16-Lead SOIC_W
16-Lead SOIC_W
16-Lead SOIC_W
Package Option
AD1856RZ
RW-16
RW-16
RW-16
RW-16
RW-16
AD1856RZ-REEL
AD1856RZ-REEL7
AD1856RZ-K
AD1856RZ-K-REEL7
0.0025%
1 Z = RoHS Compliant Part.
Rev. C | Page 15 of 16
AD1856
NOTES
Data Sheet
©1988–2013 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D00759-0-2/13(C)
Rev. C | Page 16 of 16
相关型号：
©2020 ICPDF网 联系我们和版权申明