SIHL630STRL-GE3 [VISHAY]
TRANSISTOR 9 A, 200 V, 0.4 ohm, N-CHANNEL, Si, POWER, MOSFET, TO-263AB, HALOGEN FREE AND ROHS COMPLIANT, TO-263, D2PAK-3, FET General Purpose Power;型号: | SIHL630STRL-GE3 |
厂家: | VISHAY |
描述: | TRANSISTOR 9 A, 200 V, 0.4 ohm, N-CHANNEL, Si, POWER, MOSFET, TO-263AB, HALOGEN FREE AND ROHS COMPLIANT, TO-263, D2PAK-3, FET General Purpose Power 局域网 开关 脉冲 晶体管 |
文件: | 总10页 (文件大小:244K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
IRL630S, SiHL630S
Vishay Siliconix
Power MOSFET
FEATURES
PRODUCT SUMMARY
VDS (V)
• Halogen-free According to IEC 61249-2-21
Definition
• Surface Mount
• Available in Tape and Reel
• Dynamic dV/dt Rating
• Repetitive Avalanche Rated
• Logic-Level Gate Drive
• RDS(on) Specified at VGS = 4 V and 5 V
• 150 °C Operating Temperature
• Compliant to RoHS Directive 2002/95/EC
200
RDS(on) ()
VGS = 5 V
0.40
Qg (Max.) (nC)
40
5.5
Q
Q
gs (nC)
gd (nC)
24
Configuration
Single
D
DESCRIPTION
D2PAK (TO-263)
Third generation Power MOSFETs from Vishay provide the
designer with the best combination of fast switching,
ruggedized device design, low on-resistance and
cost-effectiveness.
G
The D2PAK (TO-263) is a surface mount power package
capable of accommodating die size up to HEX-4. It provides
the highest power capability and the lowest possible
on-resistance in any existing surface mount package. The
D2PAK (TO-263) is suitable for high current applications
because of its low internal connection resistance and can
dissipate up to 2.0 W in a typical surface mount application.
D
G
S
S
N-Channel MOSFET
ORDERING INFORMATION
Package
Lead (Pb)-free and Halogen-free
D2PAK (TO-263)
SiHL630S-GE3
IRL630SPbF
D2PAK (TO-263)
D2PAK (TO-263)
SiHL630STRL-GE3a
IRL630STRLPbFa
SiHL630STL-E3a
SiHL630STRR-GE3a
IRL630STRRPbFa
SiHL630STR-E3a
Lead (Pb)-free
SiHL630S-E3
Note
a. See device orientation.
ABSOLUTE MAXIMUM RATINGS (TC = 25 °C, unless otherwise noted)
PARAMETER
SYMBOL
LIMIT
UNIT
Drain-Source Voltage
Gate-Source Voltage
VDS
VGS
200
10
V
TC = 25 °C
C = 100 °C
9.0
Continuous Drain Current
VGS at 5 V
ID
T
5.7
A
Pulsed Drain Currenta
IDM
36
Linear Derating Factor
0.59
0.025
250
9.0
W/°C
Linear Derating Factor (PCB Mount)e
Single Pulse Avalanche Energyb
Avalanche Currenta
EAS
IAR
mJ
A
Repetiitive Avalanche Energya
EAR
7.4
mJ
Maximum Power Dissipation
Maximum Power Dissipation (PCB Mount)e
Peak Diode Recovery dV/dtc
T
C = 25 °C
74
PD
W
V/ns
°C
TA = 25 °C
3.1
dV/dt
5.0
Operating Junction and Storage Temperature Range
Soldering Recommendations (Peak Temperature)
TJ, Tstg
- 55 to + 150
300d
for 10 s
Notes
a. Repetitive rating; pulse width limited by maximum junction temperature (see fig. 11).
b. VDD = 25V, starting TJ = 25 °C, L = 4.6 mH, Rg = 25 , IAS = 9.0 A (see fig. 12).
c. ISD 9.0 A, dI/dt 120 A/μs, VDD VDS, TJ 150 °C.
d. 1.6 mm from case.
e. When mounted on 1" square PCB (FR-4 or G-10 material).
* Pb containing terminations are not RoHS compliant, exemptions may apply
Document Number: 90390
S11-1044-Rev. C, 30-May-11
www.vishay.com
1
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
IRL630S, SiHL630S
Vishay Siliconix
THERMAL RESISTANCE RATINGS
PARAMETER
SYMBOL
TYP.
MAX.
UNIT
Maximum Junction-to-Ambient
RthJA
RthJA
RthJC
-
62
Maximum Junction-to-Ambient
(PCB Mount)a
-
-
40
°C/W
Maximum Junction-to-Case (Drain)
1.7
Note
a. When mounted on 1" square PCB (FR-4 or G-10 material).
SPECIFICATIONS (TJ = 25 °C, unless otherwise noted)
PARAMETER
SYMBOL
TEST CONDITIONS
MIN.
TYP.
MAX. UNIT
Static
Drain-Source Breakdown Voltage
VDS Temperature Coefficient
Gate-Source Threshold Voltage
Gate-Source Leakage
VDS
VDS/TJ
VGS(th)
IGSS
VGS = 0, ID = 250 μA
Reference to 25 °C, ID = 1 mA
VDS = VGS, ID = 250 μA
200
-
-
V
V/°C
V
-
1.0
-
0.27
-
-
-
-
-
-
-
-
2.0
100
25
VGS
VDS = 200 V, VGS = 0 V
DS = 160 V, VGS = 0 V, TJ = 125 °C
=
10 V
nA
-
Zero Gate Voltage Drain Current
Drain-Source On-State Resistance
IDSS
μA
V
-
250
0.40
0.50
-
VGS = 5.0 V
GS = 4.0 V
ID = 5.4 Ab
ID = 4.5 Ab
-
RDS(on)
gfs
V
-
Forward Transconductance
Dynamic
VDS = 50 V, ID = 5.4 Ab
4.8
S
Input Capacitance
Output Capacitance
Reverse Transfer Capacitance
Total Gate Charge
Gate-Source Charge
Gate-Drain Charge
Turn-On Delay Time
Rise Time
Ciss
Coss
Crss
Qg
-
-
-
-
-
-
-
-
-
-
1100
220
70
-
-
-
VGS = 0 V,
DS = 25 V,
f = 1.0 MHz, see fig. 5
V
pF
nC
-
40
5.5
24
-
ID = 9.0 A, VDS = 160 V,
see fig. 6 and 13b
Qgs
Qgd
td(on)
tr
VGS = 10 V
-
-
8.0
57
38
33
-
V
DD = 100 V, ID = 9.0 A,
ns
Rg = 6.0 , RD = 11 , see fig. 10b
Turn-Off Delay Time
Fall Time
td(off)
tf
-
-
D
Between lead,
Internal Drain Inductance
LD
LS
-
-
4.5
7.5
-
-
6 mm (0.25") from
package and center of
die contact
nH
G
Internal Source Inductance
S
Drain-Source Body Diode Characteristics
Continuous Source-Drain Diode Current
MOSFET symbol
showing the
integral reverse
p - n junction diode
D
IS
-
-
-
-
9.0
36
A
G
Pulsed Diode Forward Currenta
ISM
S
Body Diode Voltage
VSD
trr
TJ = 25 °C, IS = 9.0 A, VGS = 0 Vb
-
-
-
-
2.0
350
2.6
V
Body Diode Reverse Recovery Time
Body Diode Reverse Recovery Charge
Forward Turn-On Time
230
1.7
ns
μC
TJ = 25 °C, IF = 9.0 A, dI/dt = 100 A/μsb
Qrr
ton
Intrinsic turn-on time is negligible (turn-on is dominated by LS and LD)
Notes
a. Repetitive rating; pulse width limited by maximum junction temperature (see fig. 11).
b. Pulse width 300 μs; duty cycle 2 %.
www.vishay.com
2
Document Number: 90390
S11-1044-Rev. C, 30-May-11
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
IRL630S, SiHL630S
Vishay Siliconix
TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted)
100
10
100
VGS
TOP
7.50V
5.00V
4.00V
3.50V
3.00V
2.75V
2.50V
BOTTOM 2.25V
TJ = 150°C
10
1
T = 25°C
J
1
0.1
0.01
2.25V
20μs PULSE WIDTH
VDS = 50V
T
= 25°C
c
20μs PULSE WIDTH
0.1
100 A
A
0.1
1
10
2.0
2.5
3.0
3.5
4.0
4.5
5.0
V
, Drain-to-Source Voltage (V)
DS
VGS , Gate-to-Source Voltage (V)
Fig. 1 - Typical Output Characteristics, TC = 25 °C
Fig. 3 - Typical Transfer Characteristics
100
2.5
2.0
1.5
1.0
0.5
0.0
VGS
I
= 9.0A
D
TOP
7.50V
5.00V
4.00V
3.50V
3.00V
2.75V
2.50V
BOTTOM 2.25V
10
2.25V
1
20μs PULSE WIDTH
V
= 5.0V
T
= 150°C
GS
20 40 60 80 100 120 140 160
C
0.1
A
100A
-60 -40 -20
0
0.1
1
10
V
, Drain-to-Source Voltage (V)
T
J
, Junction Temperature (°C)
DS
Fig. 2 - Typical Output Characteristics, TC = 150 °C
Fig. 4 - Normalized On-Resistance vs. Temperature
Document Number: 90390
S11-1044-Rev. C, 30-May-11
www.vishay.com
3
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
IRL630S, SiHL630S
Vishay Siliconix
100
10
1
2000
V
C
C
C
= 0V,
f = 1MHz
GS
iss
rss
oss
= C + C
gs
,
C
SHORTED
gd
ds
= C
gd
ds
= C + C
gd
1500
1000
500
0
C
iss
T = 150°C
J
T = 25°C
J
C
oss
C
rss
V
GS
= 0V
A
100
0.1
A
0
0.4
0.8
1.2
1.6
1
10
V
, Drain-to-Source Voltage (V)
V
, Source-to-Drain Voltage (V)
SD
DS
Fig. 5 - Typical Capacitance vs. Drain-to-Source Voltage
Fig. 7 - Typical Source-Drain Diode Forward Voltage
100
10
I
= 9.0A
D
OPERATION IN THIS AREA LIMITED
BY R
DS(on)
V
V
V
= 160V
= 100V
= 40V
DS
DS
DS
10μs
100μs
1ms
8
6
4
2
0
10
1
10ms
100ms
T
T
= 25°C
C
J
= 150°C
FOR TEST CIRCUIT
SEE FIGURE 13
Single Pulse
0.1
A
1
10
100
1000
0
10
20
30
40
V
, Drain-to-Source Voltage (V)
Q
, Total Gate Charge (nC)
DS
G
Fig. 6 - Typical Gate Charge vs. Gate-to-Source Voltage
Fig. 8 - Maximum Safe Operating Area
www.vishay.com
4
Document Number: 90390
S11-1044-Rev. C, 30-May-11
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
IRL630S, SiHL630S
Vishay Siliconix
RD
VDS
10
8
VGS
D.U.T.
Rg
+
-
V
DD
5 V
6
Pulse width ≤ 1 µs
Duty factor ≤ 0.1 %
Fig. 10a - Switching Time Test Circuit
4
VDS
2
90 %
0
A
25
50
75
100
125
150
10 %
VGS
T , Case Temperature (°C)
C
td(on) tr
td(off) tf
Fig. 9 - Maximum Drain Current vs. Case Temperature
Fig. 10b - Switching Time Waveforms
10
1
D = 0.50
0.20
0.10
P
DM
0.05
0.1
t
1
0.02
0.01
t
2
N otes:
1. D uty factor D
SINGLE PULSE
(THERMAL RESPONSE)
=
t
/ t
2
1
2. P eak T = P
x Z
+ T
C
D M
J
thJC
0.01
A
10A
0.00001
0.0001
0.001
0.01
0.1
1
t1 , Rectangular Pulse Duration (sec)
Fig. 11 - Maximum Effective Transient Thermal Impedance, Junction-to-Case
Document Number: 90390
S11-1044-Rev. C, 30-May-11
www.vishay.com
5
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
IRL630S, SiHL630S
Vishay Siliconix
L
VDS
VDS
Vary tp to obtain
required IAS
tp
VDD
Rg
D.U.T.
IAS
+
-
VDD
VDS
5 V
0.01 Ω
tp
IAS
Fig. 12a - Unclamped Inductive Test Circuit
Fig. 12b - Unclamped Inductive Waveforms
600
500
400
300
200
100
I
D
TOP
9.0A
5.7A
BOTTOM 4.0A
V
= 50V
50
DD
A
150
0
25
75
100
125
Starting T , Juntion Temperature (°C)
J
Fig. 12c - Maximum Avalanche Energy vs. Drain Current
Current regulator
Same type as D.U.T.
50 kΩ
QG
5 V
12 V
0.2 µF
0.3 µF
QGS
QGD
+
-
VDS
D.U.T.
VG
VGS
3 mA
Charge
IG
ID
Current sampling resistors
Fig. 13a - Basic Gate Charge Waveform
Fig. 13b - Gate Charge Test Circuit
www.vishay.com
6
Document Number: 90390
S11-1044-Rev. C, 30-May-11
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
IRL630S, SiHL630S
Vishay Siliconix
Peak Diode Recovery dV/dt Test Circuit
+
Circuit layout considerations
• Low stray inductance
• Ground plane
D.U.T.
• Low leakage inductance
current transformer
-
+
-
-
+
Rg
• dV/dt controlled by Rg
+
• Driver same type as D.U.T.
• ISD controlled by duty factor “D”
• D.U.T. - device under test
VDD
-
Driver gate drive
P.W.
P.W.
D =
Period
Period
V
GS = 10 Va
D.U.T. lSD waveform
D.U.T. VDS waveform
Reverse
recovery
current
Body diode forward
current
dI/dt
Diode recovery
dV/dt
VDD
Re-applied
voltage
Body diode forward drop
Inductor current
ISD
Ripple ≤ 5 %
Note
a. VGS = 5 V for logic level devices
Fig. 14 - For N-Channel
Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon
Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and
reliability data, see www.vishay.com/ppg?90390.
Document Number: 90390
S11-1044-Rev. C, 30-May-11
www.vishay.com
7
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Package Information
Vishay Siliconix
TO-263AB (HIGH VOLTAGE)
A
B
(Datum A)
3
4
A
A
E
c2
H
L1
4
Gauge
plane
0° to 8°
4
B
5
Detail A
Seating plane
D
H
L
C
C
A1
L3
L4
Detail “A”
1
2
3
L2
Rotated 90° CW
B
B
scale 8:1
A
2 x b2
2 x b
c
E
M
M
B
0.010
A
M
0.004
B
2 x e
Base
metal
5
D1
4
Plating
(c)
b1, b3
5
c1
(b, b2)
Lead tip
4
E1
Section B - B and C - C
Scale: none
View A - A
MILLIMETERS
INCHES
MILLIMETERS
INCHES
DIM.
A
MIN.
4.06
0.00
0.51
0.51
1.14
1.14
0.38
0.38
1.14
8.38
MAX.
4.83
0.25
0.99
0.89
1.78
1.73
0.74
0.58
1.65
9.65
MIN.
0.160
0.000
0.020
0.020
0.045
0.045
0.015
0.015
0.045
0.330
MAX.
0.190
0.010
0.039
0.035
0.070
0.068
0.029
0.023
0.065
0.380
DIM.
D1
E
MIN.
6.86
MAX.
MIN.
MAX.
-
10.67
-
0.270
0.380
0.245
-
0.420
-
A1
b
9.65
6.22
E1
e
b1
b2
b3
c
2.54 BSC
0.100 BSC
H
14.61
15.88
2.79
1.65
1.78
0.575
0.625
0.110
0.066
0.070
L
1.78
0.070
L1
L2
L3
L4
-
-
-
-
c1
c2
D
0.25 BSC
0.010 BSC
4.78
5.28
0.188
0.208
ECN: S-82110-Rev. A, 15-Sep-08
DWG: 5970
Notes
1. Dimensioning and tolerancing per ASME Y14.5M-1994.
2. Dimensions are shown in millimeters (inches).
3. Dimension D and E do not include mold flash. Mold flash shall not exceed 0.127 mm (0.005") per side. These dimensions are measured at the
outmost extremes of the plastic body at datum A.
4. Thermal PAD contour optional within dimension E, L1, D1 and E1.
5. Dimension b1 and c1 apply to base metal only.
6. Datum A and B to be determined at datum plane H.
7. Outline conforms to JEDEC outline to TO-263AB.
Document Number: 91364
Revision: 15-Sep-08
www.vishay.com
1
AN826
Vishay Siliconix
2
RECOMMENDED MINIMUM PADS FOR D PAK: 3-Lead
0.420
(10.668)
0.145
(3.683)
0.135
(3.429)
0.200
0.050
(5.080)
(1.257)
Recommended Minimum Pads
Dimensions in Inches/(mm)
Return to Index
Document Number: 73397
11-Apr-05
www.vishay.com
1
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Revision: 12-Mar-12
Document Number: 91000
1
相关型号:
SIHL630STRR-GE3
TRANSISTOR 9 A, 200 V, 0.4 ohm, N-CHANNEL, Si, POWER, MOSFET, TO-263AB, HALOGEN FREE AND ROHS COMPLIANT, TO-263, D2PAK-3, FET General Purpose Power
VISHAY
SIHL640STRL-GE3
TRANSISTOR 17 A, 200 V, 0.18 ohm, N-CHANNEL, Si, POWER, MOSFET, HALOGEN FREE AND ROHS COMPLIANT, SMD-220, 3 PIN, FET General Purpose Power
VISHAY
SIHL640STRR-GE3
TRANSISTOR 17 A, 200 V, 0.18 ohm, N-CHANNEL, Si, POWER, MOSFET, HALOGEN FREE AND ROHS COMPLIANT, SMD-220, 3 PIN, FET General Purpose Power
VISHAY
©2020 ICPDF网 联系我们和版权申明