550D187X5006R2BE3 [VISHAY]
CAPACITOR, TANTALUM, SOLID, POLARIZED, 6 V, 180 uF, THROUGH HOLE MOUNT, AXIAL LEADED, ROHS COMPLIANT;型号: | 550D187X5006R2BE3 |
厂家: | VISHAY |
描述: | CAPACITOR, TANTALUM, SOLID, POLARIZED, 6 V, 180 uF, THROUGH HOLE MOUNT, AXIAL LEADED, ROHS COMPLIANT 电容器 |
文件: | 总9页 (文件大小:130K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
550D
Vishay Sprague
www.vishay.com
®
Solid-Electrolyte TANTALEX Capacitors
for High Frequency Power Supplies
FEATURES
• Terminatons: Tin/lead (SnPb), 100 % tin (RoHS
compliant)
• Hermetically-sealed, axial-lead solid tantalum
capacitors
• Small size and long life
• Exceptional capacitance stability and excellent resistance
to severe environmental conditions
• The military equivalent is the CSR21 which is qualified to
MIL-C-39003/09
Note
* Pb containing terminations are not RoHS compliant, exemptions
may apply
APPLICATIONS
Designed for power supply filtering applications at above
100 kHz.
PERFORMANCE CHARACTERISTICS
Operating Temperature: - 55 °C to + 85 °C
At + 85 °C: Leakage current shall not exceed 10 times the
(to + 125 °C with voltage derating)
values listed in the Standard Ratings table
Capacitance Tolerance: At 120 Hz, + 25 °C
20 %, 10 % standard. 5 % available as special
At + 125 °C: Leakage shall not exceed 15 times the values
listed in the standard ratings tables
Dissipation Factor: At 120 Hz, + 25 °C.
Dissipation factor, as determined from the expression
2fCR, shall not exceed the values listed in the standard
ratings tables
DC Leakage Current (DCL Max.):
At + 25 °C: Leakage current shall not exceed the values
listed in the Standard Ratings table
Life Test: Capacitors shall withstand rated DC voltage
applied at + 85 °C for 2000 h or derated DC voltage applied
at + 125 °C for 1000 h
Following the life test:
1. DCL shall not exceed 125 % of the initial requirements
2. Dissipation factor shall meet the initial requirement
3. Change in capacitance shall not exceed 5 %
ORDERING INFORMATION
550D
157
X0
006
R
2
T
E3
MODEL
CAPACITANCE
CAPACITANCE DCVOLTAGERATING
CASE
CODE
STYLE
NUMBER
PACKAGING
RoHS
COMPLIANT
TOLERANCE
AT + 85 °C
This is expressed in
picofarads. The first two
digits are the significant
figures. The third is the
number of zeros to
X0 = 20 %
X9 = 10 %
X5 = 5 % *
* Special order
This is expressed
See
2 =
T = Tape and
reel
E3 = 100 % tin
termination
in volts. To complete
Ratings
Insulated
sleeve
the three-digit block, and Case
B = Bulk (tray) (RoHS compliant)
zeros precede the
voltage rating.
Codes
table
pack
Blank = SnPb
termination
follow. Standard
capacitance ratings are
in accordance with EIA
preferred number series
wherever possible.
DIMENSIONS in inches [millimeters]
1.500 0.250
[38.10 ꢀ.35]
1.500 0.250
[38.10 ꢀ.35]
D
dia.
L1
Positive lead
+
-
0.047 [1.19] max.
0.125 [3.18] max.
Solid tinned
nickel leads
J
max.
D
L1
WITH INSULATING SLEEVE (1)
LEAD SIZE
NOMINAL DIA.
CASE
CODE
J (MAX.)
AWG NO.
R
S
0.289 0.01ꢀ [7.34 0.41]
0.351 0.01ꢀ [8.92 0.41]
0.ꢀ8ꢀ 0.031 [17.42 0.79]
0.78ꢀ 0.031 [19.9ꢀ 0.79]
0.822 [20.880]
0.922 [23.420]
22
22
0.025 [0.ꢀ4]
0.025 [0.ꢀ4]
Note
(1)
When a shrink-fitted insulation is used, it shall lap over the ends of the capacitor body
Revision: 01-Mar-12
Document Number: 40017
1
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
550D
Vishay Sprague
www.vishay.com
STANDARD RATINGS
MAX. DCL
AT + 25 °C
(μA)
MAX. DF
AT + 25 °C
120 Hz (%)
MAX. ESR
AT + 25 °C
100 kHz ()
CAPACITANCE
(μF)
CASE CODE
PART NUMBER
6 VDC AT + 85 °C, SURGE = 8 V; 4 VDC AT + 125 °C, SURGE = 5 V
150
180
220
270
330
R
R
S
S
S
550D157(1)00ꢀR2
550D187(1)00ꢀR2
550D227(1)00ꢀS2
550D277(1)00ꢀS2
550D337(1)00ꢀS2
9
10
10
10
10
12
0.0ꢀ5
0.0ꢀ0
0.055
0.050
0.045
11
12
13
15
10 VDC AT + 85 °C, SURGE = 13 V; 7 VDC AT + 125 °C, SURGE = 9 V
82
R
R
R
S
S
S
550D82ꢀ(1)010R2
550D107(1)010R2
550D127(1)010R2
550D157(1)010S2
550D187(1)010S2
550D227(1)010S2
8
8
8
8
8
8
0.085
0.075
0.070
0.0ꢀ5
0.0ꢀ0
0.055
100
120
150
180
220
10
12
15
18
20
10
15 VDC AT + 85 °C, SURGE = 20 V; 10 VDC AT + 125 °C, SURGE = 12 V
5ꢀ
ꢀ8
82
100
120
150
R
R
S
S
S
S
550D5ꢀꢀ(1)015R2
550Dꢀ8ꢀ(1)015R2
550D82ꢀ(1)015S2
550D107(1)015S2
550D127(1)015S2
550D157(1)015S2
8
ꢀ
ꢀ
ꢀ
8
8
8
0.100
0.095
0.085
0.075
0.070
0.0ꢀ5
10
12
15
18
20
20 VDC AT + 85 °C, SURGE = 26 V; 13 VDC AT + 125 °C, SURGE = 16 V
27
33
39
47
5ꢀ
ꢀ8
82
100
R
R
R
R
S
S
S
S
550D27ꢀ(1)020R2
550D33ꢀ(1)020R2
550D39ꢀ(1)020R2
550D47ꢀ(1)020R2
550D5ꢀꢀ(1)020S2
550Dꢀ8ꢀ(1)020S2
550D82ꢀ(1)020S2
550D107(1)020S2
5
7
8
5
5
5
ꢀ
ꢀ
ꢀ
ꢀ
8
0.145
0.130
0.120
0.110
0.100
0.095
0.085
0.075
9
11
14
1ꢀ
20
35 VDC AT + 85 °C, SURGE = 46 V; 23 VDC AT + 125 °C, SURGE = 28 V
8.2
10
12
15
18
22
27
33
39
47
R
R
R
R
R
R
S
S
S
S
550D825(1)035R2
550D10ꢀ(1)035R2
550D12ꢀ(1)035R2
550D15ꢀ(1)035R2
550D18ꢀ(1)035R2
550D22ꢀ(1)035R2
550D27ꢀ(1)035S2
550D33ꢀ(1)035S2
550D39ꢀ(1)035S2
550D47ꢀ(1)035S2
3
4
4
5
ꢀ
8
9
11
14
1ꢀ
4
4
4
4
4
4
4
5
5
5
0.250
0.230
0.210
0.190
0.175
0.1ꢀ0
0.145
0.130
0.120
0.110
50 VDC AT + 85 °C, SURGE = 65 V; 33 VDC AT + 125 °C, SURGE = 40 V
5.ꢀ
ꢀ.8
8.2
10
12
15
18
22
R
R
R
R
R
R
R
S
550D5ꢀ5(1)050R2
550Dꢀ85(1)050R2
550D825(1)050R2
550D10ꢀ(1)050R2
550D12ꢀ(1)050R2
550D15ꢀ(1)050R2
550D18ꢀ(1)050R2
550D22ꢀ(1)050S2
4
4
5
5
ꢀ
8
9
11
3
3
3
3
3
3
4
4
0.300
0.275
0.250
0.230
0.210
0.190
0.175
0.1ꢀ0
Note
Part number definitions:
(1) Tolerance: For 10 % tolerance specify X9; for 20 % specify “X0”; for 5 % “X5” (special order)
•
Revision: 01-Mar-12
Document Number: 40017
2
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
550D
Vishay Sprague
www.vishay.com
TAPE AND REEL PACKAGING in inches (millimeters)
13.0 (330.2)
“A”
STANDARD REEL
TAPE SPACING
COMPONENT
B
1.126 to 3.07
(28.6 to 78.0)
SPACING
A
I. D. REEL HUB
1.374 to 3.626
(34.9 to 92.1)
0.047 [1.19] MAX.
OFF CENTER (1. a)
0.625 0.0062 DIA.
(15.88 1.575)
DIA.THRU HOLE
0.125 (3.18) MAX.
0.250 (6.35) (3. b)
0.750 (19.05)
0.031 (0.79) (3. f)
BOTH SIDES (3. f)
“A”
LABEL (4. a)
SECTION “A” - “A”
TYPE 550D UNITS WITH
INSULATING SLEEVE
COMPONENT
SPACING
LEAD SIZE
TAPE SPACING
B
CASE
CODE
J
UNITS
PER REEL
(MAX.)
D
L
AWG NO.
NOM. DIA.
A
0.289 0.01ꢀ
(7.34 0.41)
0.ꢀ8ꢀ 0.031
(17.42 0.79)
0.822
(20.88)
0.025
(0.ꢀ4)
0.400 0.015
(10.1ꢀ 0.38)
2.875 0.0ꢀ2
(73.03 1.57)
R
S
22
500
500
0.351 0.01ꢀ
(8.92 0.41)
0.78ꢀ 0.031
(19.9ꢀ 0.79)
0.922
(23.42)
0.025
(0.ꢀ4)
0.400 0.015
(10.1ꢀ 0.38)
2.875 0.0ꢀ2
(73.03 1.57)
22
STANDARD REEL PACKAGING INFORMATION
1. Component Leads
g. Staples shall not be used for splicing. Not more than
4 layers of tape shall be used in any splice area and no
tape shall be offset from another by more than 0.031"
[0.79 mm] non-cumulative. Tape splices shall overlap at
least ꢀ.0" [152.4 mm] for butt joints and at least 3.0"
[7ꢀ.2 mm] for lap joints and shall not be weaker than
unspliced tape. Universal splicing clips may also be used.
h. Quantity per reel shall be controlled so that tape
components and cover shall not extend beyond the
smallest dimension of the flange (either across flats or
diameter). Once the quantity per reel for each part
number has been established, future orders for that part
number shall be packaged in that quantity. When order or
release quantity is less than the established quantity, a
standard commercial pack is to be used.
a. Component leads shall not be bent beyond 0.047"
[1.19 mm] maximum from their nominal position when
measured from the leading edge of the component lead
at the inside tape edge and at the lead egress from the
component.
b. The “C” dimension shall be governed by the overall
length of the reel packaged component. The distance
between flanges shall be 0.125" to 0.250" [3.18 mm to
ꢀ.35 mm] greater than the overall component length.
2. Orientation
All polarized components must be oriented to one
direction. The cathode lead tape shall be a color and the
anode lead tape shall be white.
i. A maximum of 0.25 % of the components per reel
quantity may be missing without consecutive missing
components.
j. Adequate protection must be provided to prevent
physical damage to both reel and components during
shipment and storage.
3. Reeling
a. Components on any reel shall not represent more than
two date codes when date code identification is required.
b. Component leads shall be positioned between pairs of
0.250" [ꢀ.35 mm] tape.
c. The disposable reels have hubs and corrugated
fibreboard flanges and core or equivalent.
4. Marking
Minimum reel and carton marking shall consist of the
following: Customer part number, purchase order no.,
quantity, package date, manufacturer’s name, electrical
value, date code, Vishay Sprague part number and
country of origin.
d. A minimum of 12.0" [304.8 mm] leader of tape shall be
provided before the first and after the last component on
the reel.
e. 50 lb or ꢀ0 lb. Kraft paper must be wound between layer
of components as far as necessary for component
protection. Width of paper to be 0.0ꢀ2" to 0.250"
[1.57 mm to ꢀ.35 mm] less than the “C” dimension
of the reel.
f. A row of components must be centered between tapes
0.047" [1.19 mm]. In addition, individual components
may deviate from center of component row
[0.79 mm].
0.031"
Revision: 01-Mar-12
Document Number: 40017
3
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
550D
Vishay Sprague
www.vishay.com
TYPICAL CURVES AT + 25 °C, IMPEDANCE AND ESR VS. FREQUENCY
10
10
IMPEDANCE
ESR
IMPEDANCE
ESR
1
1
220 µF, 10 V
120 µF, 10 V
330 µF, 6 V
180 µF, 6 V
180 µF, 6 V
120 µF, 10 V
0.1
0.1
220 µF, 10 V
150 µF, 6 V
0.01
0.01
100
1K
10K
100K
1M
10M
100
1K
10K
100K
1M
10M
FREQUENCY IN Hz
FREQUENCY IN Hz
10
1
10
1
IMPEDANCE
ESR
IMPEDANCE
ESR
47 µF, 20 V
150 µF, 15 V
100 µF, 20 V
68 µF, 15 V
68 µF, 15 V
47 µF, 20 V
0.1
0.1
150 µF, 15 V
1K
100 µF, 20 V
1K
0.01
0.01
100
10K
100K
1M
10M
100
10K
100K
1M
10M
FREQUENCY IN Hz
FREQUENCY IN Hz
10
1
10
1
IMPEDANCE
ESR
IMPEDANCE
ESR
47 µF, 35 V
22 µF, 50 V
22 µF, 35 V
22 µF, 35 V
18 µF, 50 V
18 µF, 50 V
0.1
0.1
22 µF, 50 V
47 µF, 35 V
0.01
0.01
100
1K
10K
100K
1M
10M
100
1K
10K
100K
1M
10M
FREQUENCY IN Hz
FREQUENCY IN Hz
Revision: 01-Mar-12
Document Number: 40017
4
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
550D
Vishay Sprague
www.vishay.com
PERFORMANCE CHARACTERISTICS
1.
Operating Temperature: Capacitors are designed
to operate over the temperature range of - 55 °C to
+ 85 °C with no derating.
ꢀ.
Dissipation Factor: The dissipation factor,
determined from the expression 2fCR, shall not
exceed values listed in the Standard Ratings table.
1.1
Capacitors may be operated up to + 125 °C with
voltage derating to two-thirds the + 85 °C rating.
ꢀ.1
7.
Measurements shall be made by the bridge method
at, or referred to, a frequency of 1000 Hz and a
temperature of + 25 °C.
+ 85 °C RATING
+ 125 °C RATING
Leakage Current: Capacitors shall be stabilized at
the rated temperature for 30 min. Rated voltage shall
be applied to capacitors for 5 min using a steady
source of power (such as a regulated power supply)
with 1000 resistor connected in series with the
capacitor under test to limit the charging current.
Leakage current shall then be measured.
WORKING
VOLTAGE
(V)
SURGE
VOLTAGE
(V)
WORKING
VOLTAGE
(V)
SURGE
VOLTAGE
(V)
ꢀ
8
4
5
10
15
20
35
50
13
20
2ꢀ
4ꢀ
ꢀ5
7
9
10
13
23
33
12
1ꢀ
28
40
Note that the leakage current varies with temperature
and applied voltage. See graph below for the
appropriate adjustment factor.
2.
3.
DC Working Voltage: The DC working voltage is the
maximum operating voltage for continuous duty at
the rated temperature.
TYPICAL LEAKAGE CURRENT FACTOR
RANGE AT + 25 °C
Surge Voltage: The surge DC rating is the maximum
voltage to which the capacitors may be subjected
under any conditions, including transients and peak
ripple at the highest line voltage.
1.0
0.8
0.7
0.ꢀ
0.5
0.4
3.1
3.2
Surge Voltage Test: Capacitors shall withstand the
surge voltage applied in series with a 33 5 %
resistor at the rate of 1.5 min on, 1.5 min off at
+ 85 °C, for 1000 successive test cycles.
0.3
0.2
Following the surge voltage test, the dissipation
factor and the leakage current shall meet the initial
requirements; the capacitance shall not have
changed more than 10 %.
0.1
0.08
0.07
0.0ꢀ
0.05
0.04
A
R
4.
Capacitance Tolerance: The capacitance of all
capacitors shall be within the specified tolerance
limits of the nominal rating.
0.03
0.02
4.1
Capacitance measurements shall be made by means
of polarized capacitance bridge. The polarizing
voltage shall be of such magnitude that there shall be
no reversal of polarity due to the AC component. The
maximum voltage applied to capacitors during
measurement shall be 2 VRMS at 1000 Hz at + 25 °C.
If the AC voltage applied is less than 0.5 VRMS, no DC
bias is required. Measurement accuracy of the
bridge shall be within 2 %.
0.01
0.008
0.007
0.00ꢀ
0.005
0.004
L
A
R E
F
0.003
0.002
5.
Capacitance Change with Temperature: The
capacitance change with temperature shall not
exceed the following percentage of the capacitance
measured at + 25 %
0.001
0
10 20 30 40 50 ꢀ0 70 80 90 100
PERCENT OF RATED VOLTAGE
- 55 °C
- 10 %
+ 85 °C
+ 8 %
+ 125 °C
+ 12 %
Revision: 01-Mar-12
Document Number: 40017
5
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
550D
Vishay Sprague
www.vishay.com
PERFORMANCE CHARACTERISTICS (Continued)
7.1
At + 25 °C, the leakage current shall not exceed the
10.3.4 A cathode ray oscilloscope or other comparable
means shall be used in determining electrical
intermittency during test. The AC voltage applied
value listed in the Standard Ratings table.
7.2
At + 85 °C, the leakage current shall not exceed
10 times the value listed in the Standard Ratings
table.
shall not exceed 2 VRMS
.
10.3.5 Electrical tests shall show no evidence of intermittent
contacts, open circuits or short circuits during these
tests.
10.3.ꢀ There shall be no mechanical damage to these
capacitors as a result of these tests.
10.3.7 Following the high frequency vibration test,
capacitors shall meet the original limits for
capacitance, dissipation factor and leakage current.
7.3
8.
At + 125 °C, the leakage current shall not exceed
15 times the value listed in the Standard Ratings
table.
Life Test: Capacitors shall withstand rated DC
voltage applied at + 85 °C for 2000 h or rated DC
voltage applied at + 125 °C for 1000 h.
8.1
Following the life test, the dissipation factor shall
meet the initial requirement; the capacitance change
shall not exceed 2 %; the leakage current shall not
exceed 125 % of the original requirement.
11.
Acceleration Test:
11.1 Capacitors shall be rigidly mounted by means of
suitable brackets.
9.
Shelf Test: Capacitors shall withstand a shelf test for
5000 h at a temperature of + 85 °C, with no voltage
applied.
11.2 Capacitors shall be subjected to
a constant
acceleration of 100 g for a period of 10 s in each of 2
mutually perpendicular planes.
9.1
Following the shelf test, the leakage current shall
meet the initial requirement; the dissipation factor
shall not exceed 150 % of the initial requirement; the
capacitance change shall not exceed 5 %.
11.2.1 The direction of motion shall be parallel to and
perpendicular to the cylindrical axis of the
capacitors.
11.3 Rated DC voltage shall be applied during
acceleration test.
10.
Vibration Tests: Capacitors shall be subjected to
vibration tests in accordance with the following
criteria.
11.3.1 A cathode ray oscilloscope or other comparable
means shall be used in determining electrical
intermittency during test. The AC voltage applied
10.1 Capacitors shall be secured for test by means of a
rigid mounting using suitable brackets.
shall not exceed 2 VRMS
.
10.2 Low Frequency Vibration: Vibration shall consist of a
simple harmonic motion having an amplitude of
0.03" [0.7ꢀ] and a maximum total excursion of 0.0ꢀ"
[1.52], in a direction perpendicular to the major axis
of the capacitor.
10.2.1 Vibration frequency shall be varied uniformly
between the approximate limits of 10 Hz to 55 Hz
during a period of approximately one minute,
continuously for 1 h and 1.5 h.
11.4 Electrical tests shall show no evidence of intermittent
contacts, open circuits or short circuits during these
tests.
11.5 There shall be no mechanical damage to these
capacitors as a result of these tests.
11.ꢀ Following the acceleration test, capacitors shall meet
the original limits for capacitance, dissipation factor
and leakage current.
12.
Shock Test:
10.2.2 A cathode ray oscilloscope or other comparable
means shall be used in determining electrical
intermittency during the final 30 minutes of the test.
12.1 Capacitors shall be rigidly mounted by means of
suitable brackets. The test load shall be distributed
uniformly on the test platform to minimize the effects
of unbalanced loads.
12.1.1 Test equipment shall be adjusted to produce a shock
of 100 g peak with a duration of ꢀ ms and a sawtooth
waveform at a velocity change of 9.7 ft./s.
12.2 Capacitors shall be subjected to 3 shocks applied in
each of 3 directions corresponding to the 3 mutually
perpendicular axes of the capacitors.
12.3 Rated DC voltage shall be applied to capacitors
during test.
The AC voltage applied shall not exceed 2 VRMS
.
10.2.3 Electrical tests shall show no evidence of intermittent
contacts, open circuits or short circuits during these
tests.
10.2.4 Following the low frequency vibration test,
capacitors shall meet the original requirements for
leakage current and dissipation factor; capacitance
change shall not exceed
measured value.
5 % of the original
10.3 High Frequency Vibration: Vibration shall consist of
a simple harmonic motion having an amplitude of
0.0ꢀ" [1.52] 10 % maximum total excursion or 20 g
peak, whichever is less.
10.3.1 Vibration frequency shall be varied logarithmically
from 50 Hz to 2000 Hz and return to 50 Hz during a
cycle period of 20 min.
10.3.2 The vibration shall be applied for 4 h in each of
2 directions, parallel and perpendicular to the major
axis of the capacitors.
12.3.1 A cathode ray oscilloscope or other comparable
means shall be used in determining electrical
intermittency during test. The AC voltage applied
shall not exceed 2 VRMS
.
12.4 Electrical tests shall show no evidence of intermittent
contacts, open circuits or short circuits during these
tests.
12.5 There shall be no mechanical damage to these
capacitors as a result of these tests.
12.ꢀ Following the shock test, capacitors shall meet the
original limits for capacitance, dissipation factor and
leakage current.
10.3.3 Rated DC voltage shall be applied during the
vibration cycling.
Revision: 01-Mar-12
Document Number: 40017
6
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
550D
Vishay Sprague
www.vishay.com
PERFORMANCE CHARACTERISTICS (Continued)
13.
Moisture Resistance:
15.
Thermal Shock And Immersion Cycling:
13.1 Capacitors shall be subjected to temperature
cycling at 90 % to 98 % relative humidity, in a test
chamber constructed of non-reactive materials
(non-resiniferous and containing no formaldehyde or
phenol). Steam or distilled, demineralized or
deionized water having a pH value between ꢀ.0 and
7.2 at + 23 °C shall be used to obtain the required
humidity. No rust, corrosive contaminants or
dripping condensate shall be imposed on test
specimens.
15.1 Capacitors shall be conditioned prior to temperature
cycling for 15 min at + 25 °C, at less than 50 %
relative humidity and a barometric pressure at 28" to
31".
15.2 Capacitors shall be subjected to thermal shock in a
cycle of exposure to ambient air at
- ꢀ5 °C (+ 0 °C, - 5 °C) for 30 min, then,
+ 25 °C (+ 10 °C, - 5 °C) for 5 min, then
+ 125 °C (+ 3 °C, - 0 °C) for 30 min, then
+ 25 °C (+ 10 °C, - 5 °C) for 5 min, for 5 cycles.
13.1.1 Capacitors shall be mounted by their normal
mounting means in a normal mounting position and
placed in a test chamber so that uniform and
thorough exposure is obtained.
15.3 Between 4 h and 24 h after temperature cycling,
capacitors shall be subjected to immersion in a bath
of fresh tap water with the non-corrosive dye
Rhodamine B added, at + ꢀ5 °C (+ 5 °C, - 0 °C) for
15 min, then, within 3 s, immersed in a saturated
solution of sodium chloride and water with
Rhodamine B added, at a temperature of + 25 °C
(+ 10 °C, - 5 °C) for 15 min, for 2 cycles.
13.1.2 No conditioning or initial measurements will be
performed prior to temperature cycling. Polarization
and load voltages are not applicable.
13.1.3 Capacitors shall be subjected to temperature cycling
from + 25 °C to + ꢀ5 °C to + 25 °C (+ 10 °C, - 2 °C)
over a period of 8 h, at 90 % to 98 % relative
humidity, for 20 cycles.
15.3.1 Capacitors shall be thoroughly rinsed and wiped or
air-blasted dry immediately upon removal from
immersion cycling.
13.1.4 Temperature cycling shall be stopped after an even
number of cycles 5 times during the first 18 cycles,
and the capacitor shall be alloweed to stabilize at
high humidity for 1 h to 4 h.
15.4 Capacitors shall show no evidence of harmful or
extensive corrosion, obliteration of marking or other
visible damage.
15.5 Following the thermal shock immersion cycling test,
capacitors shall meet the original requirements for
leakage current and dissipation factor; capacitance
13.1.5 After stabilization, capacitors shall be removed from
the humidity chamber and shall be conditioned for
3 h at - 10 °C 2 °C.
change shall not exceed
measured value.
5 % of the original
13.1.ꢀ After cold conditioning, capacitors shall be subjected
to vibration cycling consisting of a simple harmonic
vibration having an amplitude of 0.03" [0.7ꢀ] and a
maximum total excursion of 0.0ꢀ" [1.52] varied
uniformly from 10 Hz to 55 Hz to 10 Hz over a period
of 1 min, for 15 cycles.
15.ꢀ Capacitors shall be opened and examined. There
shall be no evidence of dye penetration.
1ꢀ.
Reduced Pressure Test:
1ꢀ.1 Capacitors shall be stabilized at a reduced pressure
of 0.315" [8.0] of mercury, equivalent to an altitude of
100 000 feet [30.480 m], for a period of 5 min.
13.1.7 Capacitors shall then be returned to temperature/
humidity cycling.
1ꢀ.2 Rated DC voltage shall be applied for 1 min.
13.2 After completion of temperature cycling, capacitors
shall be removed from the test chamber and
stabilized at room temperature for 2 h to ꢀ h.
1ꢀ.3 Capacitors shall not flash over nor shall end seals be
damaged.
1ꢀ.4 Following the reduced pressure test, the
capacitance, equivalent series resistance and
leakage current shall meet the original requirements.
13.3 Capacitors shall show no evidence of harmful or
extensive corrosion, obliteration or marking or other
visible damage.
17.
Lead Pull Test: Leads shall withstand a tensile
stress of 3 pounds (1.4 kg) applied in any direction for
30 s.
13.4 Following the moisture resistance test, capacitors
shall meet the original limits for capacitance,
dissipation factor and leakage current.
18.
Marking: Capacitors shall be marked with Sprague
or (2); the type number 550D; rated capacitance and
tolerance, rated DC working voltage and the
standard EIA date code.
14.
Insulating Sleeves:
14.1 Capacitors with insulating sleeves shall withstand a
2000 VDC potential applied for 1 min between the
case and a metal “V” block in intimate contact with
the insulating sleeve.
18.1 Capacitors shall be marked on one end with a plus
sign (+) to identify the positive terminal.
14.2 Capacitors with insulating sleeves shall have the
insulation resistance measured between the case
and a metal “V” block in intimate contact with the
insulating sleeve. The insulation resistance shall be
at least 1000 M.
18.2 Vishay Sprague reserves the right to furnish
capacitors of higher working voltages than those
ordered, where the physical size of the higher voltage
units is identical to that of the units ordered.
Revision: 01-Mar-12
Document Number: 40017
7
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
550D
Vishay Sprague
www.vishay.com
GUIDE TO APPLICATION
1.
AC Ripple Current: The maximum allowable ripple
current shall be determined from the formula:
5.
Power Dissipation: The figures shown relate to an
approximate + 20 °C rise in case temperature
measured in free air. Power dissipation will be
affected by the heat sinking capability of the
mounting surface. Non-sinusoidal ripple current may
produce heating effects which differ from those
shown. It is important that the equivalent Irms value
be established when calculating permissable
operating levels.
P
RESR
IRMS
=
------------
where,
P =
Power Dissipation in W at + 25 °C as given in
the table in paragraph number 5
(Power Dissipation)
MAXIMUM PERMISSIBLE
POWER DISSIPATION AT
+ 25 °C (W IN FREE AIR)
R
ESR = The capacitor Equivalent Series Resistance
CASE CODE
at the specified frequency
2.
AC Ripple Voltage: The maximum allowable ripple
voltage shall be determined from the formula:
R
S
0.185
0.225
P
VRMS = Z ------------
RESR
or, from the formula:
VRMS = IRMS x Z
where,
P =
Power Dissipation in W at + 25 °C as given
in the table in paragraph number 5
(Power Dissipation).
RESR
Z =
=
The capacitor Equivalent Series Resistance
at the specified frequency.
The capacitor Impedance at the specified
frequency.
2.1
2.2
The sum of the peak AC voltage plus the DC voltage
shall not exceed the DC voltage rating of the
capacitor.
The sum of the negative peak AC voltage plus the
applied DC voltage shall not allow a voltage reversal
exceeding 15 % of the DC working voltage at
+ 25 °C.
3.
4.
Reverse Voltage: These capacitors are capable of
withstanding peak voltages in the reverse direction
equal to 15 % of the DC rating at + 25 °C, 10 % of
the DC rating at + 55 °C; 5 % of the DC rating at
+ 85 °C.
Temperature Derating: If these capacitors are to be
operated at temperatures above + 25 °C, the
permissible RMS ripple current or voltage shall be
calculated using the derating factors as shown:
TEMPERATURE
+ 25 °C
DERATING FACTOR
1.0
0.8
0.ꢀ
0.4
+ 55 °C
+ 85 °C
+ 125 °C
Revision: 01-Mar-12
Document Number: 40017
8
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Revision: 12-Mar-12
Document Number: 91000
1
相关型号:
550D187X9006R2B
CAPACITOR, TANTALUM, SOLID, POLARIZED, 6 V, 180 uF, THROUGH HOLE MOUNT, AXIAL LEADED
VISHAY
550D187X9006R2BE3
CAPACITOR, TANTALUM, SOLID, POLARIZED, 6 V, 180 uF, THROUGH HOLE MOUNT, AXIAL LEADED, ROHS COMPLIANT
VISHAY
550D187X9010S2B
CAPACITOR, TANTALUM, SOLID, POLARIZED, 10 V, 180 uF, THROUGH HOLE MOUNT, AXIAL LEADED
VISHAY
550D187X9010S2BE3
CAPACITOR, TANTALUM, SOLID, POLARIZED, 10 V, 180 uF, THROUGH HOLE MOUNT, AXIAL LEADED, ROHS COMPLIANT
VISHAY
550D187X9010S2T
CAPACITOR, TANTALUM, SOLID, POLARIZED, 10 V, 180 uF, THROUGH HOLE MOUNT, AXIAL LEADED
VISHAY
550D226X0035R2B
CAPACITOR, TANTALUM, SOLID, POLARIZED, 35 V, 22 uF, THROUGH HOLE MOUNT, AXIAL LEADED
VISHAY
550D226X0035R2BE3
CAPACITOR, TANTALUM, SOLID, POLARIZED, 35 V, 22 uF, THROUGH HOLE MOUNT, AXIAL LEADED, ROHS COMPLIANT
VISHAY
550D226X0035R2T
CAPACITOR, TANTALUM, SOLID, POLARIZED, 35 V, 22 uF, THROUGH HOLE MOUNT, AXIAL LEADED
VISHAY
©2020 ICPDF网 联系我们和版权申明