EEU-FC1J101L [VICOR]
DC-DC Converter Evaluation Board;型号: | EEU-FC1J101L |
厂家: | VICOR CORPORATION |
描述: | DC-DC Converter Evaluation Board |
文件: | 总14页 (文件大小:2656K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
USER GUIDE | UG:301
PI31xx-xx-EVAL1 Cool-Power® ZVS Isolated
DC-DC Converter Evaluation Board
Chris Swartz
Principal Applications Engineer
May 2013
Contents
Page
Introduction
The PI31xx-xx-EVAL1 evaluation board allows the user to test the basic operating
principles of the PI31xx series of high density DC-DC power converters and experience
the performance and value of this solution compared to alternate conventional
solutions. Each evaluation board is populated with the components that could be used
in a final design. It is not designed or intended to be used in end product applications.
Please read this document prior to the connection of test equipment and refer to the
product datasheet for device specifications, descriptions and characteristics. Remember
to follow good lab safety practices and use safety glasses at all times.
Introduction
1
Product Description
Board Connections
Thermal Considerations
2
2
3
5
The PI31xx-xx-EVAL1 is configured to support one single input and one single output.
Each board offers pin strap options for trimming the output voltage up and down,
turning the converter on and off and adding EMI system “Y” capacitors. Additional
parts are included to compensate for line impedance associated with long leads from
the bench power supply to the converter. Additional component footprints are made
available to allow the user to test different design configurations that may be required
to meet their end needs. Kelvin type test points are included to allow for easy and
convenient connections of testing instruments for evaluation of efficiency, line/load
regulation and transient response. A low impedance oscilloscope connection using a
Johnson jack is included for ripple measurement and evaluation of the output voltage
during transient events. Each demo board is equipped with a heatsink to allow high
power operation with a small amount of air flow and to allow operation of the board
over various temperature extremes.
Max I/O Ratings
Schematic
BOMs
6
11
12
14
14
Test Setup
PCB Artwork
Mechanical Outline
Ordering Information
Figure 1.
PI31xx-xx-EVAL1
Evaluation Board
UG:301
vicorpower.com
Applications Engineering: 800 927.9474
Page 1
Cool-Power® PI31xx Series Product Description
The PI31xx operates over a wide range input, delivering 50 W or 60 W output power
depending on the individual model number. The PI31xx Series is available in a space
saving surface mountable 0.87” x 0.65” x 0.265” Power –System –in – a – Package (PSiP),
achieving ~50% space reduction versus alternative solutions.
The switching frequency of 900kHz allows for small input and output filter components
which further reduces the total size and cost of the overall system solution. The output
voltage is sensed and fed back to the internal controller using a proprietary isolated
magnetic feedback scheme which allows for high bandwidth and good common mode
noise immunity.
The PI31xx Series requires no external feedback compensation and offers a total
solution with a minimum number of external components. A rich feature set is
offered, including + 10%, -20% output voltage trim capability (depending on the model
number), remote enable, over-voltage protection, adjustable soꢀ-start, over-current
protection with auto-restart to protect against both short circuit and overload and over
and under input voltage lockout. A unique temperature monitor and protection circuit
is included that provides an analog voltage proportional to the internal die temperature,
as well as over temperature shutdown, restart and over temperature fault alarm signal.
Board Connections
1. Connect Test Equipment
a.ꢀ Connect the input DC power supply to the target board as shown in Figure 6.
The negative terminal should be wired to –IN and the positive terminal should
connect to the positive terminal of the DMM wired as a DC Ammeter. Be sure
that the proper sized wires are used to allow minimum voltage drop for a
maximum input current of up to 4 A. Use ring lugs mated to the included
fasteners on the evaluation board. If your input power supply has remote sense
capability, it can be wired to the INN and INP test points if desired. Connect the
positive terminal of the DMM to the +IN lug on the evaluation board.
ꢀ
ꢀ
b.ꢀ Connect the primary side DMM (for measuring the input voltage) to INN and
INP respectively.
c.ꢀ Connect the oscilloscope as shown in Figure 6 if you are planning to measure
both primary and secondary signals at the same time. If you do not have an
isolated differential amplifier, it is important to note that simultaneous
measurement of both primary and secondary referenced signals using an
oscilloscope with a grounded chassis is not recommended, as it will short circuit
the primary to secondary isolation barrier. Floating the oscilloscope is also not
recommended due to the large capacitance introduced by this long standing
practice. The best practice is to use an isolated differential amplifier or use an
oscilloscope with isolated channels. That is, the input returns are isolated from
each other and earth ground.
d. Connect the output DC DMM to the test points OUTN and OUTP. These test
points are done in a Kelvin type manner so that they have no high current
flowing in them.
e. Connect the DC Load to the output lugs OUT+ and OUT-. It is critical for this
connection to be low inductance.
UG:301
vicorpower.com
Applications Engineering: 800 927.9474
Page 2
2. Default Pin Strap Configuration
a.ꢀ Ensure the pin straps are in the following default locations before proceeding:
nꢀENABLE = Not Used (enabled)
nꢀTRIM_UP = Not Used
nꢀTRIM_DN = Not Used
nꢀOPT1 = Not Used
nꢀOPT2 = Not Used
3. Pin Strap Functions
a.ꢀ ENABLE – adding a strap on this pin will cause the converter to shut down.
b.ꢀ TRIM_UP – Adding a strap in this location will adjust the output voltage
up by 10%.
c.ꢀ TRIM_DN – Adding a strap in this location will adjust the output voltage down
by 10%. Only one strap can be connected at a time. If both trim straps are out,
the output voltage should be set to the model’s nominal output.
4. Trimming And Soft Start
a.ꢀ For those customers who wish to trim to another voltage by changing the preset
trim resistors to another value, the trim equation shown in Figure 2 can be used:
Figure 2.
RINT
Rlow = –V
(
•
)
PI31xx Trim Equation
desired
–Vout
+ V
(
)
desired
nom
–Vout
• VERO + V
• Vref
]
(
)
nom
desired
Rhigh
=
(
–RSS
)
•
Vref
(
–Voutnom) +
V
[
desired
Where: R1 = Rlow R3 = Rhigh VERO = 4.9 and Vref can be found in the appropriate
model datasheet.
Figure 3 shows an equation for soꢀ start configuration where C7 = C
REF
Figure 3.
−6
T
ssdesired – 230 • 10
PI31xx Soft Start Equation
CREF
=
23000
Figure 4.
PI31xx Trimming Equivalent
Circuit
ENABLE
PI31xx
Rhigh
10k
•
•
RSS
TRIM/SS
VERO
Vref
Rlow
•
SGND
UG:301
vicorpower.com
Applications Engineering: 800 927.9474
Page 3
Thermal Considerations
The PI31xx-xx-EVAL1 is supplied with optional heat sinks. At present, Picor offers four
different heat sink options to accommodate the customers space and cooling needs.
Heatsinks are available in two sizes, one with 6.3mm fins and the other with 11mm fins.
Each of those heatsinks can be ordered with a specific air flow direction in mind, both
cross flow and longitudinal are supported. Please refer to the product website
www.vicorpower.com for more information.
Table 1.
Pin
Type
Description
PI31xx-xx-EVAL1
Input-Output Pin Description
Name
IN+
Input/Lug
Input/Lug
Output/Lug
Output/Lug
Test/Pin
Primary side positive input voltage terminal.
IN-
Primary side negative input voltage terminal.
OUT+
OUT-
TM
Isolated secondary DC output voltage positive terminal.
Isolated secondary DC output voltage negative terminal.
Temperature measurement output pin with respect to SGND. 3V=300°K 10mV/°K
Signal ground, primary side referenced.
SGND
Test/Pin
Monitor pin for the soft start voltage and trim voltage reference with
respect to SGND.
TRIM/SS
ENABLE
INN
Test/Pin
Test/Pin
Test/Pin
Allows for monitoring of the ENABLE signal with respect to SGND.
Kelvin sense connection for input supply (-) and input voltage measurement
test point.
Kelvin sense connection for input supply (+) and input voltage measurement
test point.
INP
YN
Test/Pin
Output/Pad
Output/Pad
Test/Pin
Optional test pad for connection of optional “YN” capacitor to external
system ground.
Optional test pad for connection of optional “YP” capacitor to external
system ground.
YP
Kelvin sense connection for output voltage (+) and output voltage measurement
test point.
OUTP
Kelvin sense connection for output voltage (-) and output voltage measurement
test point.
OUTN
OUT
Test/Pin
Test/PIn
PCB test jack for low noise measurement of the output voltage.
Table 2.
Name
Description
PI31xx-xx-EVAL1
Evaluation Board
Pin Strap and Jumper
Description
ENABLE
TRIM_UP
TRIM_DN
OPT1
If strap is installed, unit is turned off. If strap is removed, unit will be enabled.
If strap is installed, PI3105 trims output voltage up 10%
If strap is installed, PI3105 trims output voltage down 10%
Allows optional connection of heat sink assembly to secondary return (-IN)
Allows optional connection of heat sink assembly to secondary return (-OUT)
OPT2
UG:301
vicorpower.com
Applications Engineering: 800 927.9474
Page 4
Table 3.
Name
IN+
Max Voltage
100 V
100 V
20 V
Max Current
20 A
PI31xx-xx-EVAL1
Evaluation Board
Maximum I/O Ratings
IN-
20 A
OUT+
OUT-
20 A
20 V
20 A
TRIM_DN
OPT1
OPT2
OUT
10 V
100 mA
100 mA
100 mA
100 mA
100 mA
100 mA
100 mA
100 mA
100 mA
100 mA
100 mA
100 mA
10 V
10 V
10 V
INP
10 V
INN
10 V
ENABLE
TRIM/SS
SGND
TM
10 V
10 V
10 V
10 V
OUTP
OUTN
20 V
20 V
UG:301
vicorpower.com
Applications Engineering: 800 927.9474
Page 5
Figure 5.
Schematic Diagram
H S
UG:301
vicorpower.com
Applications Engineering: 800 927.9474
Page 6
Table 4.
Item
Qty Ref Design
Part #
Value U/M Description
PI3101-00-EVAL1
Evaluation Board BOM
1.
1
U1
PI3101-00-HVIZ
NA
EA
Picor PI3101-00 High Density PSiP
GRM-
21BR71A106KE5
2.
3.
12
C8-C19
10u
F
Murata X7R Ceramic Capacitor 10 V or equiv.
C1-C4, C20-
C21
GRM-
6
1u
F
Murata X7R Ceramic Capacitor 100V or equiv.
31CR72A105KE1
GRM-
31BR73A472K
4.
5.
6.
4
1
1
CY1-CY4
4700p
4.7u
F
H
F
Murata X7R Ceramic Capacitor 1kV or equiv..
Coilcraft Inductor
L1
FP3-4R7-R
08055C391K-
AT2A
C6
390p
47u
Kemet X7R Ceramic Capacitor 50V 0805
Panasonic Electrolytic Capacitor 100V
7.
8.
1
1
1
1
1
1
8
1
C5
R1
R3
R2
R4
F1
EEU-FC2A470
F
MCR10EZPF9092 90.9k Ohm Rohm Resistor 0805 1% or equiv
9.
MCR10EZPF3013 301k
MCR10EZPF1003 100k
Ohm Rohm Resistor 0805 1% or equiv
Ohm Rohm Resistor 0805 1% or equiv
Ohm Rohm Resistor 0805 1% or equiv
10.
11.
12.
13.
14.
MCR10EZPF1000
0154003DR
100
3
A
Littlefuse Fuseblock 3A SMT
5015KCT-ND
131503100
N/A
N/A
N/A Digi-Key SMT PC Test Point
N/A Tektronix Test Jack Assembly
OUT
ENABLE,
15.
6
TSW-148-07-F-S
N/A
N/A J,Header 0.1"
TRIM UP,
TRIM_DN
Table 5.
Item
Qty Ref Design
Part #
Value U/M Description
PI3105-00-EVAL1
Evaluation Board BOM
1.
1
U1
PI3105-00-HVIZ
NA
EA
Picor PI3105-00 High Density PSiP
GRM-
21BR71A475KE5
2.
3.
6
C8-C19
4.7u
F
Murata X7R Ceramic Capacitor 16V or equiv.
C1-C4, C20-
C21
GRM-
6
1u
F
Murata X7R Ceramic Capacitor 100V or equiv.
31CR72A105KE1
GRM-
31BR73A472K
4.
5.
6.
4
1
1
CY1-CY4
4700p
470n
F
H
F
Murata X7R Ceramic Capacitor 1kV or equiv..
Coilcraft Inductor
L1
FP3-R47-R
08055C391K-
AT2A
C6
Kemet X7R Ceramic Capacitor 50V 0805
Panasonic Electrolytic Capacitor 100V
390p
47u
7.
8.
1
1
1
1
1
1
8
1
C5
R1
R3
R2
R4
F1
EEU-FC2A470
F
MCR10EZPF9092 90.9k Ohm Rohm Resistor 0805 1% or equiv
9.
MCR10EZPF3013 301k
MCR10EZPF1003 100k
Ohm Rohm Resistor 0805 1% or equiv
Ohm Rohm Resistor 0805 1% or equiv
Ohm Rohm Resistor 0805 1% or equiv
10.
11.
12.
13.
14.
MCR10EZPF1000
0154003DR
100
3
A
Littlefuse Fuseblock 3A SMT
5015KCT-ND
131503100
N/A
N/A
N/A Digi-Key SMT PC Test Point
N/A Tektronix Test Jack Assembly
OUT
ENABLE,
15.
6
TSW-148-07-F-S
N/A
N/A J,Header 0.1"
TRIM UP,
TRIM_DN
UG:301
vicorpower.com
Applications Engineering: 800 927.9474
Page 7
Table 6.
Item
Qty Ref Design
Part #
Value U/M Description
PI3106-00-EVAL1
Evaluation Board BOM
1.
1
U1
PI3106-00-HVMZ
NA
EA
Picor PI3106-00 High Density PSiP
Murata X7R Ceramic Capacitor 25V or equiv.
GRM21BR71E-
225KA73L
2.
3.
6
C8-C19
2.2u
F
C1-C4, C20-
C21
GRM31CR71H-
475KA12K
6
4.7u
F
Murata X7R Ceramic Capacitor 50V or equiv.
GRM-
31BR73A472K
4.
5.
6.
4
1
1
CY1-CY4
4700p
470n
F
H
F
Murata X7R Ceramic Capacitor 1kV or equiv..
Coilcraft Inductor
L1
FP3-R47-R
08055C391K-
AT2A
C6
Kemet X7R Ceramic Capacitor 50V 0805
Panasonic Electrolytic Capacitor 63V
390p
100u
7.
8.
1
1
1
1
1
1
8
1
C5
R1
R3
R2
R4
F1
EEU-FC1J101L
F
MCR10EZPF9092 90.9k Ohm Rohm Resistor 0805 1% or equiv
9.
MCR10EZPF3013 301k
MCR10EZPF1003 100k
Ohm Rohm Resistor 0805 1% or equiv
Ohm Rohm Resistor 0805 1% or equiv
Ohm Rohm Resistor 0805 1% or equiv
10.
11.
12.
13.
14.
MCR10EZPF1000
0154008DR
100
8
A
Littlefuse Fuseblock 8A SMT
5015KCT-ND
131503100
N/A
N/A
N/A Digi-Key SMT PC Test Point
N/A Tektronix Test Jack Assembly
OUT
ENABLE,
15.
6
TSW-148-07-F-S
N/A
N/A J,Header 0.1"
TRIM UP,
TRIM_DN
Table 7.
Item
Qty Ref Design
Part #
Value U/M Description
PI3106-01-EVAL1
Evaluation Board BOM
1.
1
U1
PI3106-01-HVIZ
NA
EA
Picor PI3106-01 High Density PSiP
GRM21BR71E-
225KA73L
2.
3.
6
C8-C19
2.2u
F
Murata X7R Ceramic Capacitor 25V or equiv.
C1-C4, C20-
C21
GRM31CR71H-
475KA12K
6
4.7u
F
Murata X7R Ceramic Capacitor 50V or equiv.
GRM-
31BR73A472K
4.
5.
6.
4
1
1
CY1-CY4
4700p
470n
F
H
F
Murata X7R Ceramic Capacitor 1kV or equiv..
Coilcraft Inductor
L1
FP3-R47-R
08055C391K-
AT2A
C6
Kemet X7R Ceramic Capacitor 50V 0805
Panasonic Electrolytic Capacitor 63V
390p
100u
7.
8.
1
1
1
1
1
1
8
1
C5
R1
R3
R2
R4
F1
EEU-FC1J101L
F
MCR10EZPF9092 90.9k Ohm Rohm Resistor 0805 1% or equiv
9.
MCR10EZPF3013 301k
MCR10EZPF1003 100k
Ohm Rohm Resistor 0805 1% or equiv
Ohm Rohm Resistor 0805 1% or equiv
Ohm Rohm Resistor 0805 1% or equiv
10.
11.
12.
13.
14.
MCR10EZPF1000
0154008DR
100
8
A
Littlefuse Fuseblock 8A SMT
5015KCT-ND
131503100
N/A
N/A
N/A Digi-Key SMT PC Test Point
N/A Tektronix Test Jack Assembly
OUT
ENABLE,
15.
6
TSW-148-07-F-S
N/A
N/A J,Header 0.1"
TRIM UP,
TRIM_DN
UG:301
vicorpower.com
Applications Engineering: 800 927.9474
Page 8
Table 8.
Item
Qty Ref Design
Part #
Value U/M Description
PI3109-00-EVAL1
Evaluation Board BOM
1.
1
U1
PI3109-00-HVMZ
NA
EA
Picor PI3109-00 High Density PSiP
GRM21BR71A-
106KE5
2.
3.
6
C8-C19
10u
F
Murata X7R Ceramic Capacitor 10V or equiv.
C1-C4, C20-
C21
GRM31CR71H-
475KA12K
6
4.7u
F
Murata X7R Ceramic Capacitor 50V or equiv.
GRM-
31BR73A472K
4.
5.
6.
4
1
1
CY1-CY4
4700p
470n
F
H
F
Murata X7R Ceramic Capacitor 1kV or equiv..
Coilcraft Inductor
L1
FP3-R47-R
08055C391K-
AT2A
C6
Kemet X7R Ceramic Capacitor 50V 0805
Panasonic Electrolytic Capacitor 63V
390p
100u
7.
8.
1
1
1
1
1
1
8
1
C5
R1
R3
R2
R4
F1
EEU-FC1J101L
F
MCR10EZPF9092 90.9k Ohm Rohm Resistor 0805 1% or equiv
9.
MCR10EZPF3013 301k
MCR10EZPF1003 100k
Ohm Rohm Resistor 0805 1% or equiv
Ohm Rohm Resistor 0805 1% or equiv
Ohm Rohm Resistor 0805 1% or equiv
10.
11.
12.
13.
14.
MCR10EZPF1000
0154008DR
100
8
A
Littlefuse Fuseblock 8A SMT
5015KCT-ND
131503100
N/A
N/A
N/A Digi-Key SMT PC Test Point
N/A Tektronix Test Jack Assembly
OUT
ENABLE,
15.
6
TSW-148-07-F-S
N/A
N/A J,Header 0.1"
TRIM UP,
TRIM_DN
Table 9.
Item
Qty Ref Design
Part #
Value U/M Description
PI3109-01-EVAL1
Evaluation Board BOM
1.
1
U1
PI3109-01-HVIZ
NA
EA
Picor PI3109-01 High Density PSiP
Murata X7R Ceramic Capacitor 25V or equiv.
GRM21BR71A-
106KE5
2.
3.
6
C8-C19
2.2u
F
C1-C4, C20-
C21
GRM31CR71H-
475KA12K
6
4.7u
F
Murata X7R Ceramic Capacitor 50V or equiv.
GRM-
31BR73A472K
4.
5.
6.
4
1
1
CY1-CY4
4700p
470n
F
H
F
Murata X7R Ceramic Capacitor 1kV or equiv..
Coilcraft Inductor
L1
FP3-R47-R
08055C391K-
AT2A
C6
Kemet X7R Ceramic Capacitor 50V 0805
Panasonic Electrolytic Capacitor 63V
390p
100u
7.
8.
1
1
1
1
1
1
8
1
C5
R1
R3
R2
R4
F1
EEU-FC1J101L
F
MCR10EZPF9092 90.9k Ohm Rohm Resistor 0805 1% or equiv
9.
MCR10EZPF3013 301k
MCR10EZPF1003 100k
Ohm Rohm Resistor 0805 1% or equiv
Ohm Rohm Resistor 0805 1% or equiv
Ohm Rohm Resistor 0805 1% or equiv
10.
11.
12.
13.
14.
MCR10EZPF1000
0154008DR
100
8
A
Littlefuse Fuseblock 8A SMT
5015KCT-ND
131503100
N/A
N/A
N/A Digi-Key SMT PC Test Point
N/A Tektronix Test Jack Assembly
OUT
ENABLE,
15.
6
TSW-148-07-F-S
N/A
N/A J,Header 0.1"
TRIM UP,
TRIM_DN
UG:301
vicorpower.com
Applications Engineering: 800 927.9474
Page 9
Table 10.
Item
Qty Ref Design
Part #
Value U/M Description
PI3110-01-EVAL1
Evaluation Board BOM
1.
1
U1
PI3110-01-HVIZ
NA
EA
Picor PI3110-01 High Density PSiP
GRM21BR71E-
225KA73L
2.
3.
6
C8-C19
2.2u
F
Murata X7R Ceramic Capacitor 25V or equiv.
C1-C4, C20-
C21
GRM31CR71H-
475KA12K
6
4.7u
F
Murata X7R Ceramic Capacitor 50V or equiv.
GRM-
31BR73A472K
4.
5.
6.
4
1
1
CY1-CY4
4700p
4.7n
F
H
F
Murata X7R Ceramic Capacitor 1kV or equiv..
Coilcraft Inductor
L1
FP3-4R7-R
08055C391K-
AT2A
C6
Kemet X7R Ceramic Capacitor 50V 0805
Panasonic Electrolytic Capacitor 100V
390p
47u
7.
8.
1
1
1
1
1
1
8
1
C5
R1
R3
R2
R4
F1
EEU-FC2A470
F
MCR10EZPF9092 90.9k Ohm Rohm Resistor 0805 1% or equiv
9.
MCR10EZPF3013 301k
MCR10EZPF1003 100k
Ohm Rohm Resistor 0805 1% or equiv
Ohm Rohm Resistor 0805 1% or equiv
Ohm Rohm Resistor 0805 1% or equiv
10.
11.
12.
13.
14.
MCR10EZPF1000
0154003DR
100
3
A
Littlefuse Fuseblock 3A SMT
5015KCT-ND
131503100
N/A
N/A
N/A Digi-Key SMT PC Test Point
N/A Tektronix Test Jack Assembly
OUT
ENABLE,
15.
6
TSW-148-07-F-S
N/A
N/A J,Header 0.1"
TRIM UP,
TRIM_DN
Table 11.
Item
Qty Ref Design
Part #
Value U/M Description
PI3111-00-EVAL1
Evaluation Board BOM
1.
1
U1
PI3111-00-HVMZ
NA
EA
Picor PI3111-00 High Density PSiP
GRM21BR71E-
225KA73L
2.
3.
6
C8-C19
2.2u
F
Murata X7R Ceramic Capacitor 25V or equiv.
C1-C4, C20-
C21
GRM31CR71H-
475KA12K
6
4.7u
F
Murata X7R Ceramic Capacitor 50V or equiv.
GRM-
31BR73A472K
4.
5.
6.
4
1
1
CY1-CY4
4700p
4.7n
F
H
F
Murata X7R Ceramic Capacitor 1kV or equiv.
Coilcraft Inductor
L1
FP3-4R7-R
08055C391K-
AT2A
C6
Kemet X7R Ceramic Capacitor 50V 0805
Panasonic Electrolytic Capacitor 63V
390p
100u
7.
8.
1
1
1
1
1
1
8
1
C5
R1
R3
R2
R4
F1
EEU-FC1J101L
F
MCR10EZPF9092 90.9k Ohm Rohm Resistor 0805 1% or equiv
9.
MCR10EZPF3013 301k
MCR10EZPF1003 100k
Ohm Rohm Resistor 0805 1% or equiv
Ohm Rohm Resistor 0805 1% or equiv
Ohm Rohm Resistor 0805 1% or equiv
10.
11.
12.
13.
14.
MCR10EZPF1000
0154003DR
100
3
A
Littlefuse Fuseblock 3A SMT
5015KCT-ND
131503100
N/A
N/A
N/A Digi-Key SMT PC Test Point
N/A Tektronix Test Jack Assembly
OUT
ENABLE,
15.
6
TSW-148-07-F-S
N/A
N/A J,Header 0.1"
TRIM UP,
TRIM_DN
UG:301
vicorpower.com
Applications Engineering: 800 927.9474
Page 10
Table 12.
Item
1.
Qty
1
Part #
PI31xx-xx-EVAL1
32786
U/M
EA
Description
PI31xx-xx-EVAL1
Packing List
Evaluation PCB Assembly
6.3mm Heatsink Assembly
11mm Heatsink Assembly
Heatsink Grounding Clip
Heatsink Pushpins
Screw, 6-32
2.
1
EA
3.
1
32784
EA
4.
1
33855
EA
5.
4
32434
EA
6.
4
N/A
EA
7.
4
N/A
EA
Nut, 6-32
Figure 6.
PI31xx-xx-EVAL1 Test Setup
OSCILLOSCOPE DC-20MHZ BW
DMM
CH1
CH2
+
-
DC
ISOLATED DIFF.
AMPLIFIER
AMMETER 0-5A
+
-
+
-
+ IN
DC
ELECT.
LOAD
0-30A
MIN
+
PS1
0-100V DC
5A
-
- IN
-
+
DMM
UG:301
vicorpower.com
Applications Engineering: 800 927.9474
Page 11
Figure 7.
Top Layer
Artwork 3 Oz Copper
Top Layer
Figure 8.
Midlayer 1
Artwork 2 Oz Copper
Midlayer 1
Figure 9.
Midlayer 2
Artwork 2 Oz. Copper
Midlayer 2
UG:301
vicorpower.com
Applications Engineering: 800 927.9474
Page 12
Figure 10.
Midlayer 3
Artwork 2 Oz. Copper
Midlayer 3
Figure 11.
Midlayer 4
Artwork 2 Oz. Copper
Midlayer 4
Figure 12.
Bottom Layer
Artwork 3 Oz. Copper
Bottom Layer
UG:301
vicorpower.com
Applications Engineering: 800 927.9474
Page 13
Figure 13.
Mechanical Drawing
3.100”
2.600”
0.250”
0.250”
0.750”
0.335”
0.150”
Cool-Power® Series
F1
Evaluation Board
High Density Isolated DC-DC Converter
IN+
OUT+
OUT
YP
L1
CY1
CY2
OUTP
INP
C5
3.100”
2.430”
R1 C6
R4 R2
R3 C7
ENABLE
TRIM_UP
TRIM_DN
INN
OUTN
OPT1 OPT2
1.55”
IN–
OUT–
CY3
CY4
YN
0.335”
PI31
-
EVAL1
0.150”
0.750”
Ordering Information
The PI31xx Customer Evaluation Boards are specified by adding the suffix “-EVAL1” to
the base PI31xx-xx model number.
Go to http://www.vicorpower.com/cms/home/company/contact-us for
ordering information.
Rev 1.0
6/13
vicorpower.com
Applications Engineering: 800 927.9474
Page 14
相关型号:
©2020 ICPDF网 联系我们和版权申明