TFS140A2 [VECTRON]
Filter Specification; 过滤器规格
| 型号： | TFS140A2 |
| 厂家： | 
Vectron International, Inc |
| 描述： | Filter Specification |
| 文件： | 总5页 (文件大小：104K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
File name: Tfs 140A2.doc
Version 1.6
14.11.2001
VI TELEFILTER
Filter Specification
TFS 140A2
1/5
1. Measurement condition :
Ambient temperature TA:
23 °C
Input power level:
0 dBm.
Terminating impedances at f * ) :
c
for input: 214
- 13,022 pF.
- 13,607 pF.
for output: 189
2. Characteristics :
Remark: Reference level for the relative attenuation a
of the TFS 140A1 is the minimum of the pass band attenuation a
. The minimum of
min
rel
the pass band attenuation a
min
is defined as the insertion loss a . The reference frequency f is the arithmetic mean value of the upper and lower
e c
frequencies at the 3 dB filter attenuation level relative to the insertion loss a . The temperature coefficient of frequency Tcf is valid both for the
e
reference frequency f and the frequency response of the filter in the operating temperature range. The frequency shift of the filter in the operating
c
temperature range is not included in the production tolerance scheme
Data
typ. value
tolerance / limit
Insertion loss (Reference level)
a
23,5 dB
max. 25 dB
e
Centre frequency
f
at ambient temperature TA (fCAT
)
140,01 MHz
140 ± 0,10 MHz
c
Pass band at ambient temperature TA:
fC - 1,55 MHz.....fC + 1,55 MHz
Amplitude ripple (p-p):
fC ...
C ± 1,35 MHz
f
C ± 1,35 MHz
0,5 dB
0,7 dB
f
f
C ± 1,42 MHz
Bandwidth at ambient temperature:
1,0 dB - band width
2,88 MHz
3,15 MHz
3,83 MHz
4,20 MHz
4,24 MHz
3
dB - band width
min. 3,0 MHz
20 dB - band width
40 dB - band width
45 dB - band width
max. 4,4 MHz
max. 5,0 MHz
Relative attenuation
a
rel
fC
fC
±
1,5
MHz
-
max.
3 dB
............
MHz
MHz
f
f
C ± 2,2
C ± 2,5
..... fC
..... fC
±
±
2,5
40
MHz
MHz
45...55 dB
60....70 dB
min. 40 dB
min. 45 dB
Group delay ( mean value in pass band ):
Group delay ripple in pass band (p-p):
Deviation from linear phase in pass band (p-p):
2,49 µs
65 ns
3,5 ° (r.m.s. 1,4°)
max. 2,5 µs
max. 100 ns
max. 10°
S11 in PB :
S22 in PB :
8
8
dB
dB
Triple transit attenuation compared to main signal
Crosstalk
52 dB
55 dB
min. 40 dB
Substrate material
Frequency inversion temperature ( To )
Temperature coefficient of frequency ( Tcf )
Quartz
25° C
-0,045
f (Hz) = Tcf(ppm/K) x (T - To)² x fTo (MHz)
ppm/K²
Frequency deviation of f over temperature: ** )
c
c
Operating temperature range
Storage temperature range
0 °C ... + 70 °C
- 40 °C ... + 85 °C
*) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as
reference values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team.
** ) fTo is reference frequency f at frequency inversion temperature (To )
c
Generated:
Dunzow W.P.
Dr. Bert Wall
Checked / Approved:
VI TELEFILTER
Potsdamer Straße 18
Vectron International, Inc.
267 Lowell Road
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: tft@telefilter.com
Hudson, NH 03051 / USA
Tel: (603) 598-0070 Fax: (603) 598-0075
E-Mail: vti@vtinh.com
VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed
as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.
File name: Tfs 140A2.doc
Version 1.6
14.11.2001
VI TELEFILTER
Filter Specification
TFS 140A2
2/5
3. Package : ( all dimensions in mm )
TFS
140A1
N22
Datecode: Year+week
1999
2000
L
M
1
19+-00,,1200
N
2001
.......
1,02
1
Pin 10
Input
Pin 1
Pin 5
Input RF Return
Output
Pin 6
Pin 2 - 4, 7 - 9
Output RF Return
Package Ground
1,91
7,62
4. 50 matching network ( see Application Note ) :
Scheme 1.
L21 L22
L3 R1
1 2
3
4
5
6
50
50
10 9 8 7
R2 L4
L11
L12
L11
L21
L3 R1
1 2
3 4 5
50
50
10 9 8 7
6
L22
R2 L4
L12
Scheme 2.
1 2
L21
L22
R1
3
4
5
C1
50
50
C2
10 9 8 7
6
R2
L11
L12
L11
L21
R1
1 2
3
4
5
6
C2
C1
50
50
L12
L22
10 9 8 7
R2
For final test we use scheme 1.
VI TELEFILTER
Potsdamer Straße 18
Vectron International, Inc.
267 Lowell Road
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: tft@telefilter.com
Hudson, NH 03051 / USA
Tel: (603) 598-0070 Fax: (603) 598-0075
E-Mail: vti@vtinh.com
VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed
as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.
File name: Tfs 140A2.doc
Version 1.6
14.11.2001
VI TELEFILTER
Filter Specification
TFS 140A2
3/5
5. Stability characteristics :
After the following tests the filter shall meet the whole specification:
1. Shock:
500g, 18 ms, half sine wave, 3 shocks each plane;
DIN IEC 68 T2 - 27
2. Vibration:
10 Hz to 500 Hz, 0,35 mm or 5g respectively, 1 octave per min, 10 cycles per plan, 3 plans;
DIN IEC 68 T2 - 6
3. Change of
temperature
-55 °C to 125°C / 30 min. each / 10 cycles
DIN IEC 68 part 2 – 14 Test N
4. Resistance to
solder heat (reflow):
max. 2 times reflow process;
for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4;
6. Packing :
Tape & Reel:
DIN IEC 286 - 3, with exception of value for N and minimum bending radius;
tape type II, embossed carrier tape with top cover tape on the upper side;
max. pieces of filters per reel:
reel of empty components at start:
reel of empty components at start including leader:
Trailer
2000
min 300 mm
min 500 mm
min 300 mm
Tape (all dimensions in mm)
W
:
:
:
:
:
:
:
:
:
32
4
1,5
1,75 ± 0,1
28,4 ± 0,1
14,2 ± 0,1
0,6
± 0,3
± 0,1
+ 0,1
Po
Do
E
So
F
G (min)
P2
P1
pull off direction
X-X
W
X
Po
P1
P2
E
t
Do
o
S
o
B
t
C
2
± 0,1
± 0,1
view direction
Ko
12
2,0
7,1
19,6 ± 0,1
2,0 ± 0,1
D1(min) :
Ao
D1
Ao
Bo
Ko
t
:
:
:
:
:
± 0,1
X
SPEC-Gurt 0061/ 19X6,5
Q09016:02.001
Jul.10,01
0,35 ± 0,35
25,5 ± 0,1
Ct
W2
Reel (all dimensions in mm):
A
W1
W2(max) :
:
:
330
32,4 + 2
38,4
N
C
A
N(min)
C
:
:
100
13 ± 0,5 / - 0,2
W1
The minimum bending radius is 45 mm. The mounting surface of the filters faces the bottom side of the embossed carrier tape.
The marking of the filters is able to read if the view is directed on the upper side of the carrier tape in the above shown direction.
VI TELEFILTER
Potsdamer Straße 18
Vectron International, Inc.
267 Lowell Road
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: tft@telefilter.com
Hudson, NH 03051 / USA
Tel: (603) 598-0070 Fax: (603) 598-0075
E-Mail: vti@vtinh.com
VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed
as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.
File name: Tfs 140A2.doc
Version 1.6
14.11.2001
VI TELEFILTER
Filter Specification
TFS 140A2
4/5
7. Air reflow temperature conditions :
1st and 2nd air reflow profile
Name:
pre-heating periods
main-heating periods
over 200 °C
peak temperature
255 °C ± 5 °C
Temperature: 150 °C - 170 °C
Time:
60 sec. - 90 sec.
20 sec. - 25 sec.
Air reflow profile
260
240
220
200
180
160
140
120
100
80
60
40
20
0
0
20
40
60
80
100
120
140
160
180
200
220
240
time / sec.
Table for temperature vs. time during the air reflow process
Tolerance of temperatures: ± 5 °C
time / sec.
0
10
20
30
40
50
60
70
80
90
100
110
120
130
temperature / °C
time / sec.
140
150
160
170
180
190
195
200
205
210
215
220
230
240
temperature / °C
23
34
46
60
80
103
121
134
143
150
154
156
158
159
160
161
164
170
180
205
230
255
230
205
180
165
140
120
VI TELEFILTER
Potsdamer Straße 18
Vectron International, Inc.
267 Lowell Road
D 14 513 TELTOW / Germany
Hudson, NH 03051 / USA
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
Tel: (603) 598-0070 Fax: (603) 598-0075
E-Mail: tft@telefilter.com
E-Mail: vti@vtinh.com
VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed
as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.
File name: Tfs 140A2.doc
Version 1.6
14.11.2001
VI TELEFILTER
Filter Specification
TFS 140A2
5/5
History :
Version Reason of changes
Name
Date
1.0
1.1
Generate specification according to customer requirements.
Dunzow W.
Dunzow W.
15.05.2000
31.05.2000
Add theoretical matching network scheme.
Change filter name from TFS 140A11 to TFS 140A1.
Change input and output pin positions according to customer requirements.
1.2
1.3
Correct errors in matching network scheme.
Dunzow W.
Dunzow W.
05.06.2000
22.06.2000
Change limit value ILo : from ILo = max. 19 dB to ILo = max. 20 dB.
Correct wrong unit for limit value of TTS ( ns
Add VSWR according to customer requirement.
dB ).
1.4
1.5
Edit typical values after measured.
Edit termination impedances .
Dunzow W.
Dunzow W.
18.07.2000
25.10.2001
correct “ 5. Stability characteristics ”.
add one modified matching networks.
change limit lines and tolerance for centre frequency.
1.6
change limit value of the group delay ripple :
Dunzow W.
14.11.2001
from max.200 ns to max.100 ns according to customer requirements.
change termination impedances and insertion loss .
change specification name (from 140A1 to 140A2 )
delete limits value for VSWR.
VI TELEFILTER
Potsdamer Straße 18
Vectron International, Inc.
267 Lowell Road
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: tft@telefilter.com
Hudson, NH 03051 / USA
Tel: (603) 598-0070 Fax: (603) 598-0075
E-Mail: vti@vtinh.com
VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed
as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.
相关型号：
©2020 ICPDF网 联系我们和版权申明