LTA065B0D2F [TOSHIBA]
LCD 6.5INCH 640X480 VGA;型号: | LTA065B0D2F |
厂家: | TOSHIBA |
描述: | LCD 6.5INCH 640X480 VGA CD |
文件: | 总12页 (文件大小:104K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
17cm COLOUR TFT-LCD MODULE
(6.5 TYPE)
Toshiba Matsushita Display Technology Co., Ltd
LTA065B0D2F
(a-Si TFT)
PRODUCT INFORMATION
All information is subject to change without notice. Please read bottom notes.
FEATURES:(1)6.5” VGA color display with High Luminance (400cd/m2)
(2)Wide Viewing Angle (Vertical:120°, Horizontal:140°)
(3)Built in Long Life LEDs (MTBF:70,000 h)
TENTATIVE
(Condition; Ta=25°C, PWM=100%(continuous lighting))
(4)Replaceable structure of LED units
RoHS compatible
MECHANICAL SPECIFICATIONS
Item
Dimensional Outline (typ.)
Number of Pixels
Active Area
Pixel Pitch
Weight (approximately)
Backlight
Specifications
153.0 (W) x 121.0 (H) x 10.9 typ(D) mm
640
(W) x 480 (H) pixels
132.48 (W) x 99.36 (H) mm
0.207 (W) x 0.207 (H)
(250 g)
Sidelight ( LEDs )
ABSOLUTE MAXIMUM RATINGS
Item
Min.
-0.3
0
-0.3
-20
-30
Max.
4.0
20.0
VDD+0.3
70
Unit
V
V
V
°C
°C
(VDD
(VLED
(VIN)
)
)
Supply Voltage
Input Signal Voltage
Operating Temperature *1
Storage Temperature
Storage Humidity
80
10
90
%(RH)
(Max. wet bulb temperature = 39°C)
*1 : Only operation is guarantied at Operating Temperature. Display quality is evaluated at +25°C.
ELECTRICAL SPECIFICATION (Ta=25°C) (RECOMMENDED OPERATION CONDITION)
Item
Min.
3.0
10.8
250
1.0
2.2
0
2.2
0
0
Typ.
3.3
12.0
---
1.25
---
---
---
---
---
Max.
3.6
13.2
450
2.0
VDD
0.7
VDD
0.7
3.3
---
Unit
V
V
mV
V
V
V
V
V
Remarks
(VDD
(VLED
(VID)
(VCM
(VIH)
(VIL)
)
)
Supply Voltage
Differential Input Voltage
Common Mode Input Voltage
High Level Input Voltage
Low Level Input Voltage
Backlight ON/OFF signal
)
U/D, L/R
U/D, L/R
ON
(VON/OFF
)
OFF
Luminance control signal
Current Consumption
(VPWM
(IDD) *2
(ILED
)
V
---
---
---
(165)
(260)
(3.7)
mA
mA
W
)
---
---
PWM=100%
PWM=100%
Power Consumption *2
*2 : 8 color bars pattern
OPTICAL SPECIFICATION (Ta=25°C)
Item
Min.
250
---
---
---
Typ.
500
120
140
15
25
400
70,000
Max.
---
---
---
---
Unit
---
°
Remarks
Contrast Ratio
Viewing Angle
(CR ≥ 10)
(CR)
(Upper+Lower)
(Left+Right)
°
(TON
)
ms
ms
cd/m2
h
Response Time
(TOFF
)
---
(280)
---
---
Luminance
(L)
PWM=100%
PWM=100%
LED Life Time (MTBF) *3 *4
*3 : Conditions ;Ta=25°C, continuous lighting
*4 : Definitions of failure ; 1) Lcd luminance becomes half of the minimum value. 2) LED doesn’t light normally.
*The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by
Toshiba Matsushita Display Technology or other rights of the third parties which may result from its use. No license is granted by
implication or otherwise under any patent or patent rights of Toshiba Matsushita Display Technology or others.
*The information contained herein may be changed without prior notice. It is therefore advisable to contact Toshiba Matsushita Display
Technology before proceeding with the design of equipment incorporating this product.
(1/12)
2008-04-17 (Ver.0.5R)
LTA065B0D2F
Unit : mm
Standard tolerance : +/-0.5
DIMENSIONAL OUTLINE
TENTATIVE
<Front side>
3 0 . + / 5 - 9
. 3 / + - 5 0 . 2 9
) a e r A
i v c e t ( A . 3 9 6 9
2 . 9 1 1
6 ) 1 . ( 6
5 8 5 . 1 0
1 2 1
4 2 9 .
3 0 . + / 5 - 9
. 3 / + - 5 0 . 2 9
(2/12)
2008-04-17 (Ver.0.5R)
LTA065B0D2F
Unit : mm
Standard tolerance : +/-0.5
TENTATIVE
<Rear side>
5 7 . 5
8 2 + / - 0 . 3
0 . 3
1 3 . 6 + / -
7 2 . 7
( 8 6 . 7 )
(3/12)
2008-04-17 (Ver.0.5R)
LTA065B0D2F
BLOCK DIAGRAM
640 pixels
X,1
X,2
640,1
640,2
1,1
1,2
1,Y
X,Y
640,Y
480 pixels
1,480
X,480
640,480
SEQUENCE OF POWER SUPPLIES AND SIGNALS
500ms (Min.)
3.0V
3.
0V
0.2V
0.2V
0.2V
DD
V
40ms
0ms
(Max.)
(Min.
40ms (Max.
)
0
ms (Min.)
)
CLK+/-
RxIN0+/-
RxIN1+/-
RxIN2+/-
VCM
VID
25
0ms
(
Min.)
0ms (M
in.)
VON/OFF
LED Driver ON/OFF
(4/12)
2008-04-17 (Ver.0.5R)
LTA065B0D2F
TIMING CHART
<H-Sync/V-Sync+DE Mode>
(5/12)
2008-04-17 (Ver.0.5R)
LTA065B0D2F
<DE-Only Mode>
(6/12)
2008-04-17 (Ver.0.5R)
LTA065B0D2F
TIMING SPECIFICATION 1) 2) 3) 4) 5)
<H-Sync/V-Sync+DE Mode>
Item
Symbol
min.
500
---
20
2
typ.
525
16.67
45
Max.
550
17.85
70
unit
th
ms
th
th
Frame Period
tv
Vertical blanking Term
V-sync Pulse Width
tvblnk
tvw
---
---
Vertical Front Porch
Vertical Data Sync Period
Vertical Display Term
tvfp
tvds
tvde
2
6
480
740
31.5
8
---
---
---
---
480
860
---
---
---
---
640
40.0
---
---
---
th
th
th
tc
us
tc
tc
tc
480
800
31.75
160
---
Horizontal Period
th
H-sync Pulse Width
Horizontal Front Porch
Horizontal Data Sync Period
Horizontal Display Term
Clock Period
Clock “L” Time
Clock “H” Time
Data Setup Time
Data Hold Time
thw
thfp
thds
thde
tc
8
8
---
640
35.0
10.0
10.0
5.0
10.0
640
39.7
---
---
---
tc
ns
ns
ns
ns
ns
tcl
tch
tds
tdh
---
---
<DE-Only Mode>
Item
Symbol
min.
500 x t3
---
480 x t3
740 x t5
31.5
640 x t5
35.0
10.0
typ.
525 x t3
16.67
480 x t3
800 x t5
31.75
640 x t5
39.7
Max.
550 x t3
17.85
480 x t3
860 x t5
---
unit
---
ms
---
---
Frame Period
t1
t2
t3
Vertical Display Term
One Line Scanning Term
us
---
Horizontal Display Term
Clock Period
Clock “L” Time
Clock “H” Time
Data Setup Time
Data Hold Time
t4
t5
t6
t7
t8
t9
640 x t5
40.0
ns
ns
ns
ns
ns
---
---
---
---
---
---
---
---
10.0
5.0
10.0
Note 1) Refer to “Timing Chart” and LVDS(DS90C365*, DS90C385*) specifications by National Semiconductor Corp.
Note 2) If NCLK is fixed to "H" or "L" level for certain period while DE is supplied, the panel may be damaged.
Note 3) If DE is fixed to “H” or “L” level for certain period while NCLK is supplied, the panel displays black with some flicker.
Note 4) Please adjust LCD operating signal timing and LED PWM frequency, to optimize the display quality.
There is a possibility that flicker is observed by the interference of LCD operating signal timing and PWM condition
(especially driving frequency), even if the condition satisfies above timing specifications and recommended operating
conditions.
Note 5) Do not make tv(t1), th(t2) and tvds(t3) fluctuate.
Note 6) In case of using the long frame period, the deterioration of display quality, noise etc. may be occurred.
Note 7) NCLK count of each Horizontal Scanning Time should be always the same.
V-Blanking period should be “n” X “Horizontal Scanning Time”. (n: integer)
Frame period should be always the same.
(7/12)
2008-04-17 (Ver.0.5R)
LTA065B0D2F
CONNECTOR PIN ASSIGNMENT FOR INTERFACE
CN1 INPUT SIGNAL
Connector : 20268-020E-12F / I-PEX CO., LTD.
Mating Connector : 20230-020B-F or 20230-T20-F or 20230-W20B-F / I-PEX CO., LTD.
DF19G-20S-1C(Plug), DF19A-2830SCFA(Crimp contact)
Terminal No.
Symbol
VDD
VDD
Function
Power Supply : +3.3V
Power Supply : +3.3V
1
2
3
VSS
GND
4
VSS
GND
5
6
7
RxIN0-
RxIN0+
VSS
Negative LVDS differential data input (R0-R5, G0)
Positive LVDS differential data input (R0-R5, G0)
GND
8
9
RxIN1-
RxIN1+
VSS
RxIN2-
RxIN2+
VSS
Negative LVDS differential data input (G1-G5, B0-B1)
Positive LVDS differential data input (G1-G5, B0-B1)
GND
Negative LVDS differential data input (B2-B5, HS, VS, DE)
Positive LVDS differential data input (B2-B5, HS, VS, DE)
GND
Clock Signal(-)
10
11
12
13
14
15
16
17
18
19
20
CLK-
CLK+
CLKEDID
U/D
L/R
NC
Clock Signal(+)
DDC clock
Vertical Reverse(“L” level or Open : Normal, “H” level : Reverse)
Horizontal Reverse(“L” level or Open : Normal, “H” level : Reverse)
Non Connection (open)
DATAEDID
DDC data
Note 1) See next page.
CN2 LED INPUT SIGNAL
Connector : 53261-0671 / MOLEX Inc.
Mating Connector : 51021-0600 / MOLEX Inc.
Terminal No.
Symbol
VLED
VLED
VSS
VSS
ON/OFF
PWM
Function
1
2
3
4
5
6
Power Supply : +12V
Power Supply : +12V
GND
GND
“H(+3.3V)”:ON, “L(GND or Open)”:OFF
1-100%(200Hz)
(8/12)
2008-04-17 (Ver.0.5R)
LTA065B0D2F
RECOMMENDED TRANSMITTER (DS90C365* by National Semiconductor Corp.)
TO LTA065B0D2F INTERFACE ASSIGNMENT
Case1: 6bit Transmitter
DS90C365*
LTA065B0D2F
Interface
(CN1)
Input Terminal No.
Input Signal
(Graphics controller output signal)
Output
Signal
Symbol
Symbol
TIN0
TIN1
TIN2
TIN3
TIN4
TIN5
TIN6
TIN7
Terminal
44
45
47
48
1
Symbol Function
Terminal
Symbol
R0
R1
R2
R3
R4
R5
G0
G1
G2
G3
G4
G5
B0
B1
B2
B3
B4
B5
Red Pixels Display Data (LSB)
Red Pixels Display Data
Red Pixels Display Data
Red Pixels Display Data
Red Pixels Display Data
Red Pixels Display Data (MSB)
Green Pixels Display Data (LSB)
Green Pixels Display Data
Green Pixels Display Data
Green Pixels Display Data
Green Pixels Display Data
Green Pixels Display Data (MSB)
Blue Pixels Display Data (LSB)
Blue Pixels Display Data
TOUT0-
TOUT0+
No.5
No.6
RxIN0-
RxIN0+
3
4
6
7
TIN8
TIN9
TOUT1-
TOUT1+
No.8
No.9
RxIN1-
RxIN1+
9
TIN10
TIN11
TIN12
TIN13
TIN14
TIN15
TIN16
TIN17
TIN18
TIN19
TIN20
CLK IN
10
12
13
15
16
18
19
20
22
23
25
26
Blue Pixels Display Data
Blue Pixels Display Data
Blue Pixels Display Data
Blue Pixels Display Data (MSB)
TOUT2-
TOUT2+
No.11
No.12
RxIN2-
RxIN2+
HSYNC H-Sync
VSYNC V-Sync
DE
CLK
Compound Synchronization Signal
Data Sampling Clock
TCLK OUT-
No.14
CLK-
TCLK OUT+ No.15
CLK+
Note 1) Please connect NC pin to nothing. Don't connect it to ground nor to other signal input.
T IN6
G0
T IN5
R5
T IN4
R4
T IN3
R3
T IN2
R2
T IN1
R1
T IN0
R0
Rx IN0
T IN7
G1
T IN13
B1
T IN12
B0
T IN11
G5
T IN10
G4
T IN9
G3
T IN8
G2
Rx IN1
Rx IN2
T IN20
DE
T IN14
B2
T IN19
T IN18
T IN17
B5
T IN16
B4
T IN15
B3
VSYNC
HSYNC
(9/12)
2008-04-17 (Ver.0.5R)
LTA065B0D2F
RECOMMENDED TRANSMITTER (DS90C385* by National Semiconductor Corp.)
TO LTA065B0D2F INTERFACE ASSIGNMENT
Case2: 8bit Transmitter
DS90C385*
LTA065B0D2F
Interface
(CN1)
Input Terminal No.
Input Signal
(Graphics controller output signal)
Output
Signal
Symbol
Symbol
TIN0
TIN1
TIN2
TIN3
TIN4
TIN6
TIN7
TIN8
Terminal
51
52
54
55
56
3
Symbol Function
Terminal
Symbol
R0
R1
R2
R3
R4
R5
G0
G1
G2
G3
G4
G5
B0
B1
B2
B3
B4
B5
Red Pixels Display Data (LSB)
Red Pixels Display Data
Red Pixels Display Data
Red Pixels Display Data
Red Pixels Display Data
Red Pixels Display Data (MSB)
Green Pixels Display Data(LSB)
Green Pixels Display Data
Green Pixels Display Data
Green Pixels Display Data
Green Pixels Display Data
Green Pixels Display Data(MSB)
Blue Pixels Display Data (LSB)
Blue Pixels Display Data
TOUT0-
TOUT0+
No.5
No.6
RxIN0-
RxIN0+
4
6
7
TIN9
TOUT1-
TOUT1+
No.8
No.9
RxIN1-
RxIN1+
TIN12
TIN13
TIN14
TIN15
TIN18
TIN19
TIN20
TIN21
TIN22
TIN24
TIN25
TIN26
TIN27
TIN5
TIN10
TIN11
TIN16
TIN17
TIN23
CLK IN
11
12
14
15
19
20
22
23
24
27
28
30
50
2
Blue Pixels Display Data
Blue Pixels Display Data
Blue Pixels Display Data
Blue Pixels Display Data (MSB)
TOUT2-
TOUT2+
No.11
No.12
RxIN2-
RxIN2+
HSYNC H-Sync
VSYNC V-Sync
DE
NC
NC
NC
NC
NC
NC
NC
CLK
Compound Synchronization Signal
Non Connection (open)
Non Connection (open)
Non Connection (open)
Non Connection (open)
Non Connection (open)
Non Connection (open)
Non Connection (open)
Data Sampling Clock
TOUT3-
TOUT3+
8
10
16
18
25
31
TCLK OUT-
No.14
CLK-
TCLK OUT+ No.15
CLK+
Note 1) Please connect NC pin to nothing. Don't connect it to ground nor to other signal input.
T IN7
G0
T IN6
R5
T IN4
R4
T IN3
R3
T IN2
R2
T IN1
R1
T IN0
R0
Rx IN0
T IN8
G1
T IN1 8
B1
T IN1 5
B0
T IN14
G5
T IN13
G4
T IN 12
G3
T IN 9
G2
Rx IN1
Rx IN2
Rx IN3
T IN2 6
DE
T IN1 9
B2
T IN2 5
T IN24
T IN22
B5
T IN21
B4
T IN20
B3
VSYNC
HSYNC
T IN2 3
NC
T IN1 7
NC
T IN16
NC
T IN11
NC
T IN10
NC
T IN5
NC
T IN2 7
NC
(10/12)
2008-04-17 (Ver.0.5R)
LTA065B0D2F
256k (k=1024) COLORS COMBINATION TABLE
Gray Scale
Level
---
R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0
Display
L
L
L
L
H
H
H
H
L
L
L
L
L
L
L
H
H
H
H
L
L
L
L
L
L
L
H
H
H
H
L
L
L
L
L
L
L
H
H
H
H
L
L
L
L
L
L
L
H
H
H
H
L
L
H
L
L
L
L
H
H
H
H
L
H
L
L
L
H
H
L
L
H
H
L
L
L
L
L
H
H
L
L
H
H
L
L
L
L
L
H
H
L
L
H
H
L
L
L
L
L
H
H
L
L
H
H
L
L
L
L
L
H
H
L
L
H
H
L
L
L
L
L
H
H
L
L
H
H
L
L
L
L
H
L
H
L
H
L
H
L
L
L
L
H
L
H
L
H
L
H
L
L
L
L
H
L
H
L
H
L
H
L
L
L
L
H
L
H
L
H
L
H
L
L
L
L
H
L
H
L
H
L
H
L
L
L
L
H
L
H
L
H
L
H
L
L
L
Black
Blue
Green
Light Blue
Red
Purple
Yellow
White
Black
---
---
---
---
---
---
---
L 0
Basic
Color
L 1
L 2
Dark
↑
↓
Gray
Scale of
Red
:
:
:
:
:
:
L3…
L60
Light
H
H
H
L
L
L
H
H
H
L
L
L
H
H
H
L
L
L
H
H
H
L
L
L
L
H
H
L
L
L
H
L
H
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
H
L
L
L
L
H
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L61
L62
Red
L63
Red
Black
L 0
L 1
L 2
Dark
↑
↓
Gray
Scale of
Green
:
:
:
:
:
:
L3…
L60
Light
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
H
H
H
L
L
L
H
H
H
L
L
L
H
H
H
L
L
L
H
H
H
L
L
L
L
H
H
L
L
L
H
L
H
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
H
L
L
L
L
H
L
L61
L62
Green L63
Green
Black
L 0
L 1
L 2
Dark
↑
↓
Gray
Scale of
Blue
:
:
:
:
:
:
L3…
L60
Light
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
H
L
L
L
L
H
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
H
L
L
L
L
H
L
H
H
H
L
L
L
H
H
H
L
L
L
H
H
H
L
L
L
H
H
H
L
L
L
L
H
H
L
L
H
H
L
H
L
H
L
L61
L62
Blue
L 0
L63
Blue
Black
L 1
L 2
Dark
↑
↓
Gray
Scale of
White &
Black
:
:
:
:
:
:
L3…
L60
Light
H
H
H
H
H
H
H
H
H
H
H
H
L
H
H
H
L
H
H
H
H
H
H
H
H
H
H
H
H
H
L
H
H
H
L
H
H
H
H
H
H
H
H
H
H
H
H
H
L
H
H
H
L
H
L61
L62
White L63
White
(11/12)
2008-04-17 (Ver.0.5R)
LTA065B0D2F
!
FOR SAFETY
LCD module is generally designed with precise parts to achieve light weighted thin mechanical dimensions.
In using our Modules, make certain that you fully understand and put into practice the warnings and safety precautions detailed
in Engineering Information No.EE-N001,"CAUTIONS AND INSTRUCTIONS FOR TOSHIBA LCD MODULES".
Refer to individual specifications and TECHNICAL DATA sheets (hereinafter called "TD") for more detailed technical
information.
1) SPECIAL PURPOSES
A) Toshiba Matsushita Display Technology's Standard LCD Modules have not been customized for operation in extreme
environments or for use in applications where performance failures could be life-threatening or otherwise catastrophic.
B) Since Toshiba Matsushita Display Technology's Standard LCD Modules have not been designed for operation in extreme
environments, they must never be used in devices that will be exposed to abnormally high levels of vibration or shock which
exceed Toshiba Matsushita Display Technology's published specification limits.
C) In addition, since Toshiba Matsushita Display Technology Standard LCD Modules have not been designed for use in
applications where performance failures could be life-threatening or catastrophic, they must never be installed in aircraft
navigation control systems (such as, but not limited to Traffic Collision Avoidance System and Air Traffic Indicator), in military
defense or weapons systems, in critical industrial process-control systems (e.g., those involved in the production of nuclear
energy), or in critical medical device or patient life-support systems.
2) DISASSEMBLING OR MODIFICATION
DO NOT DISASSEMBLE OR MODIFY the module. It may damage sensitive parts inside LCD module, and may cause
scratches or dust on the display.
Toshiba Matsushita Display Technology doses not warrant the module, if customer disassembled or modified it.
3) BREAKAGE OF LCD PANEL
DO NOT INGEST liquid crystal material, DO NOT INHALE this material, and DO NOT CONTACT the material with skin, if LCD
panel is broken and liquid crystal material spills out.
If liquid crystal material comes into mouth or eyes, rinse mouth or eyes out with water immediately.
If this material contact with skin or cloths, wash it off immediately with alcohol and rinse thoroughly with water.
4) GLASS OF LCD PANEL
BE CAREFUL WITH CHIPS OF GLASS that may cause injuring fingers or skin, when the glass is broken.
5) ELECTRIC SHOCK
DISCONNECT POWER SUPPLY before handling LCD module.
DO NOT TOUCH the parts inside LCD module and the fluorescent lamp's connector or cables in order to prevent electric
shock, because high voltage is supplied to these parts from the inverter unit while power supply is turned on.
6) ABSOLUTE MAXIMUM RATINGS AND POWER PROTECTION CIRCUIT
DO NOT EXCEED the absolute maximum rating values under the worst probable conditions caused by the supply voltage
variation, input voltage variation, variation in parts' constants, environmental temperature, etc., otherwise LCD module may be
damaged.
Employ protection circuit for power supply, whenever the specification or TD specifies it.
Suitable protection circuit should be applied for each system design.
7) RECOMMENDED OPERATION CONDITIONS
The performance and quality of the LCD panel are warranted only when the LCD panel is used within “the recommended
operation conditions”. Toshiba Matsushita Display Technology Co., Ltd. never warrants the performance and quality of the
LCD panel when you use the LCD panel over “the recommended operation conditions”, although within “the absolute
maximum rating”.
To use the LCD panel over “the recommended operation conditions” may have bad influence on the characteristics and
reliability of the LCD panel and may shorten the life of the LCD panel.
Therefore, when designing the whole set, not to be over “the recommended operation conditions”, you should fully take care of
supply voltage change, characteristic of connection parts, serge of input-and-output line, and surrounding temperature.
8) DISPOSAL
When dispose LCD module, obey to the applicable environmental regulations.
(12/12)
2008-04-17 (Ver.0.5R)
相关型号:
©2020 ICPDF网 联系我们和版权申明