LTA070B0N0A [TOSHIBA]
LCD DOT MATRIX GRAPHIC DISPLAY MODULE;
| 型号： | LTA070B0N0A |
| 厂家： | 
TOSHIBA |
| 描述： | LCD DOT MATRIX GRAPHIC DISPLAY MODULE CD |
| 文件： | 总15页 (文件大小：228K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Toshiba Matsushita Display Technology Co., Ltd
18cm FULL-COLOR
TFT-LCD MODULE
PRODUCT INFORMATION
LTA070B0N0A
FEATURES
(1) a-Si TFT-LCD for portable DVD.
(2) Analog RGB input.
(3) High luminance & wide viewing angle.
(4) Slim, thin, and light weight design.
(5) This product conforms to RoHS Directive.
TENTATIVE
GENERAL SPECIFICATIONS
Items
Specifications
Note
Screen size
Display mode
Contents
18cm (7-Type) diagonal screen
TN full color, Transmissive type
TFT-cell, Driver-ICs, Backlight-unit
Normally white
Refer to figure A
(Next sheet)
Viewing direction
Driving method
6 o’clock (in direction of maximum CR)
a-Si TFT active matrix, Line sequential scanning
Non-Interlace drive
Horizontal/Vertical start pulse and clock
Vertical (gate) enable
Sync.
Input
signal
Signal
Common
Specified analog RGB signals (H-line inverted)
H-line alternate signal
Number of pixels
480(W) x 234(H)
Note 1
Number of sub-pixels 1440(W) x 234(H)
Note 1
Pixel pitch
0.321(W) x 0.370(H)
RGB stripe
166.0(W) x 100.0(H) x 7.0(D) (typ.)
154.08 (W) x 86.58 (H)
[unit: mm]
Note 1
[unit: mm]
[unit: mm]
Pixel arrangement
Dimensional outline
Active area
Backlight
Surface treatment
Weight
FL side light (L type 1 lamp)
Anti-glare coating on LCD panel surface. Wide view film
175 (typ.)
[unit: g]
Environmental care
This product conforms to RoHS Directive.
Note 1: Pixel arrangement
1
2
3
4
5
1437 1438 1439 1440
P ixe l
Ｒ Ｇ Ｂ Ｒ Ｇ
Ｒ Ｇ Ｂ Ｒ Ｇ
Ｂ Ｒ Ｇ Ｂ
Ｂ Ｒ Ｇ Ｂ
1
2
Ｒ Ｇ Ｂ
Sub p ixe l
=dot
Ｒ Ｇ Ｂ Ｒ Ｇ
Ｒ Ｇ Ｂ Ｒ Ｇ
Ｂ Ｒ Ｇ Ｂ
Ｂ Ｒ Ｇ Ｂ
233
234
Ｒ Ｇ Ｂ
*The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by
Toshiba Matsushita Display Technology Co., Ltd. or other rights of the third parties which may result from its use. No license is granted
by implication or otherwise under any patent or patent rights of Toshiba Matsushita Display Technology Co., Ltd. or others.
*The information contained herein may be changed without prior notice. It is therefore advisable to contact Toshiba Matsushita Display
Technology Co., Ltd. before proceeding with the design of equipment incorporating this product.
Toshiba Matsushita Display Technology Co., Ltd
CONFIDENTIAL
(1/15)
2007-07-05 (Ver.0.6)
LTA070B0N0A
Figure A: Viewing direction
Viewing direction: 6 o’clock (Max. contrast ratio)
ABSOLUTE MAXIMUM RATINGS (Note 1)
Items
Symbol
VDD
Conditions
Ta=25°C
Ta=25°C
Ta=25°C
Ta=25°C
Ta=25°C
Ta=25°C
Ta=25°C
Ta=25°C
-
Min.
Max.
6.5
Unit
Remarks
VSS=0
Supply voltage
-0.3
V
VEE
VGON
VSS
-0.3
6.5
V
-0.3
45.0
V
V
VGON-45.0
VGON+0.3
3000
VEE+0.3
VDD+0.3
13.0
VFL
-
-0.3
-0.3
-10.0
-20
-
V(rms)
V
Input signal voltage
Analog
Logic
VANA
VIN
Note 4
Note 5
V
Common
VCOM
V
Operating temperature
Operating humidity
Storage temperature
Storage humidity
70
°C
Top
Hop
Tstg
Hstg
Note 2, 3
Note 3
90
%(RH)
°C
-
-30
-
80
-
95
%(RH)
-
Note 1: Do not exceed the maximum rating values under the worst probable conditions taking into account the supply
voltage variation, input voltage variation, variation in part constants, and ambient temperature and so on. Otherwise
the module may be damaged.
Note 2: The temperature of the module rises under the influence of the backlight. Please design that all parts of this
module do not to exceed maximum operation temperature (Top).
Note 3: The temperature on TFT-LCD panel surface.
Note 4: Terminals; VR, G, B
Note 5: Terminals; CLK1, CLK2, CLK3, STH1, STH2, OEH, MODE, RL, CPV, STV1, STV2, OEV1, OEV2, OEV3, U/D
Toshiba Matsushita Display Technology Co., Ltd
CONFIDENTIAL
(2/15)
2006-08-04 (Ver.0.5)
LTA070B0N0A
OUTLINE DIMENSIONS
30.2±0.2
3.6±0.15
51±0.2
3.6±0.15
51±0.2
Unit: mm
3.6±0.15
0.2
(2)
5
Ｓｑｕａｒｅ ｈｏｌｅｓ ｆｏｒ ｉｎｓｔａｌｌｉｎｇ（２ｈｏｌｅｓ）．
Ｔｈｅ ｕｓａｂｌｅ ｄｅｐｔｈｓ ｏｆ ｔｈｅｓｅ ｈｏｌｅｓ ａｒｅ
ｗｉｔｈｉｎ １．６ｍｍ．
.
.15
±
Ｔｈｅ ｅｊｅｃｔｉｏｎ ｐｏｉｎｔｓ ｏｆ ｔｈｅ ｌａｍｐ ｈａｒｎｅｓｓ
166±0.3
２
157.9(Frame window)
154.08(Active area)
2.8
4.72±0.5
４
２
9.3
4
７±０．３
5
2.3
34.4
Ｔｈｅｒｍａｌ ｃｏｎｔｒａｃｔｉｌｅ
)
w
o
L
(
5
±
0
3
ｔｕｂｅｓ
)
5
(
±
3.1
3
)
.
Ｎｏ１ ＰＩＮ
ＬＯＷ
8(.
2
1
5
2
.
Ｄｏｔ ｎｕｍｂｅｒ（Ｗ×Ｈ）：１４４０×２３４
12.
2
.
0
7
1
0
Ｄｏｔ ｐｉｔｃｈ
：０．１０７×０．３７０
±
Ｎｏ２ ＰＩＮ
ＨＩＧＨ
.
4
4
ＲＧＢ ａｒｒａｎｇｅｍｅｎｔ：Ｖｅｒｔｉｃａｌ ｓｔｒｉｐｅ
±
1
1
.
(
5
)
3
0
±
5
(
H
i
g
)
h
)
4
ow)
5
rea
2
ind
3
.
2
1
12
140
2±0.2
1±0.15
2±0.2
1±0.15
v
±
m
6
6
t
±
.
(Fr
2
58(
.
86.
φ
１
Ｂａｃｋ ｆｒａｍｅ ｗｉｎｄｏｗ
5
5
Ａ
.
2
0
±
Ｆｒｏｎｔ ｓｉｄｅ
3
3
4
Ｍａｉｎ ｖｉｅｗｉｎｇ
Ａ
Ｓｑｕａｒｅ ｈｏｌｅｓ ｆｏｒ
ａｎｇｌｅ ｄｉｒｅｃｔｉｏｎ
60
Ｓｑｕａｒｅ ｈｏｌｅｓ ｆｏｒ
ｉｎｓｔａｌｌｉｎｇ（２ｈｏｌｅｓ）．
Ｔｈｅ ｄｅｐｔｈｓ ｏｆ ｔｈｅｓｅ
ｈｏｌｅｓ ａｒｅ ｗｉｔｈｉｎ ０．５ｍｍ．
ｉｎｓｔａｌｌｉｎｇ（２ｈｏｌｅｓ）．
６
30.5±0.2
3.6±0.15
103±0.2
５
７
３
Ｔｈｅ ｕｓａｂｌｅ ｄｅｐｔｈｓ ｏｆ ｔｈｅｓｅ
ｈｏｌｅｓ ａｒｅ ｗｉｔｈｉｎ ０．５ｍｍ．
3.6±0.15
.15
±
5
.
2
Ｎｏｔｅ
・Ｍａｉｎ ｖｉｅｗｉｎｇ ａｎｇｌｅ ｉｓ
６ ｏ′ｃｌｏｃｋ ｄｉｒｅｃｔｉｏｎ
2
.
1
ｗｈｅｎ ＦＰＣ ｉｓ ｌｏｃａｔｅｄ ｂｅｌｏｗ ｔｈｅ ｐａｎｅｌ．
・Ｔｈｉｓ ｄｉｍｅｎｓｉｏｎ ｓｈｏｕｌｄ ｂｅ ｍｅａｓｕｒｅｄ ｕｎｄｅｒ
ｔｈｅ ｃｏｎｄｉｔｉｏｎ ｐｒｅｓｓｅｄ ｂｙ ｔｈｅ ｆｏｒｃｅ ｏｆ
１ｋｇｆ ｗｉｔｈ １０ｍｍ ｄｉａｍｅｔｅｒ ｇａｕｇｅ．
15
27.5
15.5
.1±
0
82±
(20)
(64.24)
1
Ｓｑｕａｒｅ ｈｏｌｅｓ ｆｏｒ ｉｎｓｔａｌｌｉｎｇ（２ｈｏｌｅｓ）．
Ｔｈｅ ｕｓａｂｌｅ ｄｅｐｔｈｓ ｏｆ ｔｈｅｓｅ ｈｏｌｅｓ ａｒｅ
ｗｉｔｈｉｎ ０．５ｍｍ
Ａｎｄ ｉｔ ｓｈｏｕｌｄ ｎｏｔ ｃｏｎｔａｉｎ ｓｌｉｇｈｔ ｓｗｅｌｌｉｎｇ．
・Ｄｏ ｎｏｔ ｔｏｕｃｈ ＦＰＣ ｗｉｔｈ ｏｔｈｅｒ ｐａｒｔｓ ｂｙ ｆｏｒｃｅ．
1
Ｐｌｅａｓｅ ｕｓｅ ＦＰＣ ｗｉｔｈ ｂｅｎｄｉｎｇ ｎａｔｕｒａｌｌｙ．
・Ｇｅｎｅｒａｌ ｔｏｌｅｒａｎｃｅ ｉｓ ±０．３
Ｎｏｔｅ） Ｋｅｅｐ ｔｈｅ ｍａｓｋ ａｎｄ／ｏｒ
Ｆｌｅｘｉｂｌｅ ｃａｂｌｅ
ｉｔｓ ｂｕｒｒｓ ａｗａｙ ｆｒｏｍ ｔｈｅ
ｐｏｌａｒｉｚｅｒ．Ｔｈｅ ｌｕｑｕｉｄ
ｃｒｙｓｔａｌ ｍａｙ ｌｏｏｋ ｌｉｋｅ
ｗａｖｉｎｇ ｗｈｅｎ ｔｈｅ ｍａｓｋ ｉｓ
ｔｏｕｃｈｉｎｇ ｔｈｅ ｐｏｌａｒｉｚｅｒ．
ｃｏｎｔａｃｔｉｎｇ ｓｕｒｆａｃｅ（ｂａｃｋ ｓｉｄｅ）
Ｔｈｅ ｔｈｒｅｅ ｚｏｎｅｓ ｏｎ ｔｈｅ ｒｅａｒ ｓｉｄｅ ｏｆ ｔｈｅ ｍｏｄｕｌｅ
（ｉｌｌｕｓｔｒａｔｅｄ ｗｉｔｈ ｔｈｅ ｓｔｒｉｐｅｓ
）
ａｒｅ ｔｏ ｂｅ ｌａｂｅｌｌｅｄ，ｓｏ ｙｏｕｒ ｄｅｓｉｇｎ ｎｅｅｄ ｔｏ ｍａｋｅ
ｔｈｅ ｐｏｉｎｔ ｔｏ ｂｅ ｇｒｏｕｎｄｅｄ ｗｉｔｈｏｕｔ ｔｈｅｓｅ ａｒｅａｓ．
ＢＭ
Ｐｏｌａｒｉｚｅｒ
・Ｎｅｖｅｒ ｆａｉｌ ｔｏ ｃｏｎｎｅｃｔ ｔｈｅ ｆｒｏｎｔ（ｏｒ ｔｈｅ ｂａｃｋ） ｃｏｖｅｒ
・
ｏｆ ｔｈｅ ｓｅｔ ｔｏ ｔｈｅ ｇｒｏｕｎｄ．
Ｐｏｌａｒｉｚｅｒ
ＬＣＤ Ｐａｎｅｌ
)
Ｍａｓｋ
0(.
154.08
(0.5)
(0.5)
2
1.3±0.4(ALL)
0.2
.
8
68.
Ａｃｔｉｖｅ ａｒｅａ
Ｎｏｔｅ）
・Ｐｌｅａｓｅ ａｓｋ ｕｓ ｗｈｅｎ ｙｏｕ ｄｅｓｉｇｎ
ｍａｓｋｉｎｇ ｓｔｒｕｃｔｕｒｅ ｂｅｃａｕｓｅ ｔｈｅ ｌｉｇｈｔ
ｌｅａｋ ｆｒｏｍ ｔｈｅ ｏｕｔｅｒ ｓｉｄｅ ｏｆ ａｃｔｉｖｅ
ａｒｅａ ｍａｙ ｏｃｃｕｒ．
)
ＳＥＣＴ Ａ－Ａ
（Ｓ＝５／１）
Ｍａｓｋｉｎｎｇ ｄｉｍｅｎｓｉｏｎ
ｒｅｃｏｍｍｅｎｄｅｄ
0(.
Ｐｏｌａｒｉｚｅｒ
ａｔｔａｃｈｍｅｎｔ ｐｏｓｉｔｉｏｎ
Toshiba Matsushita Display Technology Co., Ltd
CONFIDENTIAL
(3/15)
2006-05-23 (Ver.0.4)
LTA070B0N0A
CIRCUIT BLOCK DIAGRAM
COG P a n e l
1440 x 234 do ts
Sou r ce D r ive r
FPC
CN 1
VCOM
R ,G ,B
CLK1 ,CLK2 ,CLK3 ,STH1 ,STH2 ,OEH ,MODE ,RL
VEE
VDD
CPV ,STV1 ,STV2 ,OEV1 ,OEV2 ,OEV3 ,U /D
VSS
VGON
CN 2
CCFL
Toshiba Matsushita Display Technology Co., Ltd
CONFIDENTIAL
(4/15)
2006-08-04 (Ver.0.5)
LTA070B0N0A
VIDEO SIGNAL TIMING CHART
NTSC (Full scan mode)
HD
VD
1st display period
(22H - 256H)
2nd display period
(285H - 519H)
Xout
STV
2
3
4
5
6
7
17
22 23
265266267268269
280
285286287
t1V=262.5 x t1H
tsvw
(5-stage flip-flops exist in the gate driver)
t1H=608 x tchw
STH 1 , 2
CLK 1,2,3
tchw
Invalid data
Valid data
Invalid data
480 481
R, G, B
605 606 607 608
1
2
608
1
HD
(tss) tshw
(tvs)
STH 1 , 2
R, G, B
(tohs) tohw tosp
toc
OEH
CPV
tcvwh
tcvwl
tcvw
tsovc
thovc
OEV1
OEV2
OEV3
Note: At the time of a power on sequence, OEV should hold on “Hi” at least 1 frame period (t1V), after STV and CPV are
inputted.
Toshiba Matsushita Display Technology Co., Ltd
CONFIDENTIAL
(5/15)
2006-08-04 (Ver.0.5)
LTA070B0N0A
CONTROL SIGNAL TIMING CHART
tchw
tchwh
tchwl
CLK1
tchd12
CLK2
tchd23
CLK3
tshset
tshhld
STH1,2
R,G,B
tshw
1
3
2
tcvw
tcvwh
tcvwl
CPV
tsvset
tsvhld
STV1,2
tsvw
Toshiba Matsushita Display Technology Co., Ltd
CONFIDENTIAL
(6/15)
2006-08-04 (Ver.0.5)
LTA070B0N0A
Remarks
TIMING SPECIFICATION
NTSC (Full scan mode)
Signal Parameter
Frame frequency
Frame period
Symbol
1/t1v
t1V
Min.
Typ.
Max.
Unit
Hz
-
57.143
59.939
62.852
262.5 x t1H 262.5 x t1H 262.5 x t1H
608 x tchw 608 x tchw 608 x tchw
-
1 Line scanning period
t1H
60.6
100.0
9.20
31.4
47.1
47.1
1.45
30.0
10.0
20.0
1.59
-
63.6
104.6
9.56
34.9
52.3
52.3
9.85
104.6
52.3
52.3
10.00
1.4
66.6
108.6
9.95
38.4
57.5
57.5
10.96
208.0*
-
μs
ns
Period
tchw
1/tchw
tchd
Frequency
MHz
ns
ns
ns
μs
ns
ns
ns
μs
μs
μs
μs
μs
μs
μs
μs
μs
CLK1,
CLK2,
CLK3
Pulse delay
Pulse width (Hi)
Pulse width (Lo)
Rising of STH to HD
Pulse width
Setup
tchd12,tchd23
tchwh
tchwl
tss
Reference value
*tshset=tshhld
tshw
tshset
tshhld
tvs
STH1,
STH2
Hold
-
R,G,B Video input to HD
Rising of OEH to HD
11.11
1.9
Reference value
Reference value
tohs
OEH
Falling of OEH to STH
Pulse width
tosp
0.0
0.5
-
tohw
tcvw
toc
7.5
8.0
8.5
Period
10.0
1.5
63.5
2.3
-
Rising of CPV to OEH
Pulse width (Hi)
Pulse width (Lo)
Rising of OEV to CPV
-
CPV
tcvwh
tcvwl
tsovc
5.0
10.3
53.2
1.5
58.5
58.5
2.0
5.0
OEV1,
OEV2,
OEV3,
1.0
Falling of OEV to CPV
thovc
2.0 x tchw 3.0 x tchw 4.0 x tchw
-
Pulse width
Setup
tsvw
tsvset
tsvhld
5.0
63.5
31.75
31.75
126.0**
μs
μs
μs
**tsvset=tsvhld
STV1,
STV2
2.00
2.00
-
-
Hold
Toshiba Matsushita Display Technology Co., Ltd
CONFIDENTIAL
(7/15)
2006-08-04 (Ver.0.5)
LTA070B0N0A
INTERFACE PIN ASSIGNMENT
CN1: INPUT SIGNAL
FPC: 0.5mm pitch
Mating connector: IL-FPR series/Japan Aviation Electronics Industry, Limited
Pin No.
1
Symbol
VCOM
STH1
NC
Functions
Voltage applied to color filter substrate
Source scanning start signal 1
Non Connect
Remarks
2
Note 2
3
4
R
Red video signal
5
G
Green video signal
6
B
Blue video signal
7
OEH
VDD
MODE
CLK1
CLK2
CLK3
RL
Source driver output enable
Power line for logic (3.3V)
8
9
Sampling mode change (H: Simultaneous, L: Sequential) Note 3
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Source driver clock input 1
Source driver clock input 2
Source driver clock input 3
Right / Left scanning change
Source scanning start signal 2
Power line for source driver IC (5.0V)
Ground (0V)
Note 3
Note 3
Note 3
Note 2
Note 2
STH2
VEE
GND
VCOM
STV2
OEV3
OEV2
OEV1
CPV
U/D
Voltage applied to color filter substrate
Gate scanning start signal 2
Gate driver output enable 3
Gate driver output enable 2
Gate driver output enable 1
Gate driver scanning clock pulse
Up/Down scanning change
Gate scanning start signal 1
Non connect
Note 1
Note 1
Note 1
STV1
NC
VSS
GND
VDD
NC
Gate driver negative voltage (-13.0V)
Ground (0V)
Power line for logic (3.3V)
Non connect
VGON
Gate driver positive voltage (17.0V)
CN2: CCFL POWER SOURCE
Connector: BHSR-02VS-1 / J.S.T. Mfg. Co., Ltd.
Mating connector: SM02B-BHSS-1 / J.S.T. Mfg. Co., Ltd.
No.
1
Symbol
Functions
FL power supply for backlight (GND)
FL power supply for backlight (HOT)
I/O
Remarks
Input
Input
V FLL
V FLH
White
Red
2
Toshiba Matsushita Display Technology Co., Ltd
CONFIDENTIAL
(8/15)
2006-08-04 (Ver.0.5)
LTA070B0N0A
Note 1: Switch scanning direction of UP/DOWN as follows:
UD
STV1
Output
Input
STV2
Input
Output
Remarks
usual
Up to down
Down to up
Lo
Hi
Up to down
Down to up
COG Panel
COG Panel
Source Driver
Source Driver
FPC
FPC
Note 2: Switch scanning direction of RIGHT/LEFT as follows:
RL
STH1
Input
STH2
Output
Input
Remarks
usual
Left to right
Right to left
Hi
Lo
Output
Left to right
Right to left
COG Panel
COG Panel
Source Driver
Source Driver
FPC
FPC
Note 3: Set source sampling mode as follows:
MODE
CLK1
Input
Input
CLK2
Input
Hi
CLK3
Input
Hi
Sequential sampling
Lo
Hi
Synchronous sampling
Toshiba Matsushita Display Technology Co., Ltd
CONFIDENTIAL
(9/15)
2006-08-04 (Ver.0.5)
LTA070B0N0A
SEQUENCE FOR POWER ON/OFF AND SIGNAL ON/OFF
ＶＧＯＮ
ＶＥＥ
Rising
ＶＤＤ
90%
０Ｖ
０Ｖ
ＶＳＳ
≧0ns
Logic signal, Vcom,
RGB-video signal
ＯＦＦ
ＯＦＦ
ＯＮ
T1
T3
T2
T4
1) 10ms ≤ T1 < T2 , 0 < T3 < T4 ≤ 10ms
2) Please use the schottky barrier diode as follows;
COG P a n e l
1440
x 234 do ts
Sou r ce D r i ve r
FPC
CN 1
VCOM
R ,G ,B
VEE
VDD
CLK1 ,CLK2 ,CLK3 ,STH1 ,STH2 ,OEH ,MODE ,RL
VEE
VDD
CPV ,STV1 ,STV2 ,OEV1 ,OEV2 ,OEV3 ,U /D
VSS
VGON
VGON
Toshiba Matsushita Display Technology Co., Ltd
CONFIDENTIAL
(10/15)
2006-08-04 (Ver.0.5)
LTA070B0N0A
ELECTRICAL SPECIFICATION (Ta=25℃) (RECOMMENDED OPERATING CONDITION) (Note 1)
Items
Symbol
VDD
VEE
VGON
VSS
VFL
Min.
2.7
Typ.
3.3
Max.
3.6
Unit
Remarks
Supply voltage
V
4.5
5.0
5.5
V
16.0
-14.0
-
17.0
-13.0
600
-
18.0
V
-12.0
V
-
V(rms)
IFL=6.5mA(rms) Note 2
Input
signal
voltage
Logic low level
Logic high level
Video black (+)
Video white (+)
Video black (-)
Video white (-)
Video amplitude
Video center
VIL
0.0
0.2 x VDD
VDD
V
VIH 0.80 x VDD
-
V
VSB+
VSW+
VSB-
(0.20)
(VSB+)
(VSW-)
(0.20)
-
0.75
4.25
4.25
0.75
3.5
(VSW+)
(4.80)
(4.80)
(VSB-)
VEE-0.4
V
R,G,B, VEE=5.0V Note 3
R,G,B, VEE=5.0V Note 3
R,G,B, VEE=5.0V Note 3
R,G,B, VEE=5.0V Note 3
R,G,B Note 3
V
V
VSW-
VSPP
V
V(p-p)
V
VSC VEE/2-0.2
VEE/2 VEE/2+0.2
R,G,B Note 3
VCOM amplitude
VCOM center
VCPP
VCOMC
3.0
-0.5
7.0
0.5
9.0
1.5
V(p-p)
V
Note 3
Note 3, Note 4
(VSPP+VCPP)/2
-
-
30
-
40
-
5.5
80
V
kHz
Note 3
Note 5
FL driving frequency
fFL
FL starting voltage
Supply current
VSFL
IDD
1700
-
-
V(rms)
mA
-20°C Note 6
1.79
3.60
VDD=3.3V Note 7, 8
VEE=5.0V,
VB=2.0V,
Note 7
IEE
-
19.60
39.20
mA
IGH
ISS
IFL
-
0.12
-0.30
6.5
1.00
-
mA
mA
VGON=17.0V Note 7
VSS=-13.0V Note 7
-1.00
3.0
7.0
mA(rms)
Note 1 : The recommended operating conditions show the ranges in which the device can operate normally. Operation beyond
the limit of the recommended operating conditions is not assured, even though operating conditions are within the limit
of the absolute maximum ratings.
Note 2: FL input current values are reference.
Toshiba Matsushita Display Technology Co., Ltd
CONFIDENTIAL
(11/15)
2006-08-04 (Ver.0.5)
LTA070B0N0A
Note 3: R, G, B and VCOM should be inverted every 1H as follows (an example of input timing).
VCOM driving circuit should be designed with 50Ω or less output impedance.
100%
White
Composite video signal
Pedestal
Pedestal
VSB-
VSW+
VSC
4.25V
VSPP
R,G,B
2.5V
0.75V
VSB+
Pedestal
VSW-
4.0V
0.5V
VCPP
(variable)
VCOM
VCOMC
-3.0V
1H
1H
Note 4: Adjust for minimum flicker.
Note 5: Recommended for Horizontal frequency: 40.0kHz
Note 6: Initial value.
Note 7: Not peak current value but continuous one.
Note 8: Measured under synchronous sampling operation.
Toshiba Matsushita Display Technology Co., Ltd
CONFIDENTIAL
(12/15)
2006-08-04 (Ver.0.5)
LTA070B0N0A
OPTICAL SPECIFICATION (Ta=25℃)
Characteristics
Symbol
Condition
Standard value
Unit
Measuring method
θ
φ
C.
MIN.
300
100
TYP.
400
300
MAX.
Luminance
L
-
-
cd/m2 IFL=6.5mA(rms)
0°
0°
Contrast ratio
Cmax
-
-
-
best angle
x
y
0°
0°
0°
0°
0.275
0.300
0.7
0.315
0.340
-
0.355
White color chromaticity
0°
0°
0.380
-
Brightness uniformity
Vertical viewing angle
-
-
-
0°
0°
-
20
40
45
45
-
30
60
60
60
11
22
-
-
°
°
θU
θD
φL
φR
τr
≥10
≥10
≥10
≥10
-
0°
0°
0°
0°
-
°
Horizontal viewing angle
-
-
°
0°
0°
22
44
ms
ms
Response time
Backlight life
-
τd
Continuous lighting
Note 1
-
-
-
10000
20000
-
h
Note 1: Period till Brightness falls 50% from the initial value. Reference value at continuous lighting.
Toshiba Matsushita Display Technology Co., Ltd
CONFIDENTIAL
(13/15)
2006-08-04 (Ver.0.5)
LTA070B0N0A
!
FOR SAFETY
LCD module is generally designed with precise parts to achieve light weighted thin mechanical dimensions.
In using our Modules, make certain that you fully understand and put into practice the warnings and safety precautions detailed in
Engineering Information No.EE-N001,"CAUTIONS AND INSTRUCTIONS FOR TOSHIBA MATSUSHITA DISPLAY
TECHNOLOGY LCD MODULES".
Refer to individual specifications and TECHNICAL DATA sheets (hereinafter called "TD") for more detailed technical information.
1) SPECIAL PURPOSES
A) Toshiba Matsushita Display Technology's Standard LCD Modules have not been customized for operation in extreme
environments or for use in applications where performance failures could be life-threatening or otherwise catastrophic.
B) Since Toshiba Matsushita Display Technology's Standard LCD Modules have not been designed for operation in extreme
environments, they must never be used in devices that will be exposed to abnormally high levels of vibration or shock which
exceed Toshiba's published specification limits.
C) In addition, since Toshiba Matsushita Display Technology's Standard LCD Modules have not been designed for use in
applications where performance failures could be life-threatening or catastrophic, they must never be installed in aircraft
navigation control systems (such as, but not limited to Traffic Collision Avoidance System and Air Traffic Indicator), in military
defense or weapons systems, in critical industrial process-control systems (e.g., those involved in the production of nuclear
energy), or in critical medical device or patient life-support systems.
2) DISASSEMBLING OR MODIFICATION
DO NOT DISASSEMBLE OR MODIFY the module. It may damage sensitive parts inside LCD module, and may cause scratches
or dust on the display.
Toshiba Matsushita Display Technology does not warrant the module, if customer disassembled or modified it.
3) BREAKAGE OF LCD PANEL
DO NOT INGEST liquid crystal material, DO NOT INHALE this material, and DO NOT CONTACT the material with skin, if LCD
panel is broken and liquid crystal material spills out.
If liquid crystal material comes into mouth or eyes, rinse mouth or eyes out with water immediately.
If this material contact with skin or cloths, wash it off immediately with alcohol and rinse thoroughly with water.
4) GLASS OF LCD PANEL
BE CAREFUL WITH CHIPS OF GLASS that may cause injuring fingers or skin, when the glass is broken.
5) ELECTRIC SHOCK
DISCONNECT POWER SUPPLY before handling LCD module. DO NOT TOUCH the parts inside LCD module in order to
prevent electric shock, because high voltage is supplied to these parts while power supply is turned on.
6) ABSOLUTE MAXIMUM RATINGS AND POWER PROTECTION CIRCUIT
DO NOT EXCEED the absolute maximum rating values under the worst probable conditions caused by the supply voltage
variation, input voltage variation, variation in parts' constants, environmental temperature, etc., otherwise LCD module may be
damaged.
Employ protection circuit for power supply, whenever the specification or TD specifies it.
Suitable protection circuit should be applied for each system design.
7) DISPOSAL
When dispose LCD module, obey to the applicable environmental regulations.
Toshiba Matsushita Display Technology Co., Ltd
CONFIDENTIAL
(14/15)
2006-08-04 (Ver.0.5)
LTA070B0N0A
Revision History
Date
Ver
Item
Old
New
Reason
Page ﾞ
(new)
Toshiba Matsushita Display technology Co., Ltd.
SALES & MARKETING DIV.
AV-USE SALES & MARKETING DEPT.
4-1-8, Kounan, Minato-ku, Tokyo, 108-0075, JAPAN
TEL : 03-5462-7280, FAX : 03-3458-0078
Toshiba Matsushita Display Technology Co., Ltd
CONFIDENTIAL
(15/15)
2006-08-04 (Ver.0.5)
相关型号：
©2020 ICPDF网 联系我们和版权申明