TMSDVC5416GGUR160 [TI]
TMS320VC5416 Fixed-Point Digital Signal Processor; TMS320VC5416定点数字信号处理器
| 型号： | TMSDVC5416GGUR160 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | TMS320VC5416 Fixed-Point Digital Signal Processor |
| 文件： | 总98页 (文件大小：855K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
TMS320VC5416
Fixed-Point Digital Signal Processor
Data Manual
Literature Number: SPRS095O
March 1999–Revised January 2005
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
TMS320VC5416
Fixed-Point Digital Signal Processor
SPRS095O–MARCH 1999–REVISED JANUARY 2005
Revision History
This data sheet revision history highlights the technical changes made to the SPRS095N device-specific
data sheet to make it an SPRS095O revision.
Scope: This document has been reviewed for technical accuracy; the technical content is up-to-date as of
the specified release date with the following corrections.
SECTION
ADDITIONS/CHANGES/DELETIONS
Section 5.2
Changed IOH from -2 to -8 mA and IOL from 2 to 8 mA. Changed Note 2 to read "These output current limits are
used for the test conditions on VOL and VOH, except where noted otherwise."
Chapter 6
Removed Section 6.2 to prevent duplication of Product Information.
2
Revision History
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
Contents
Revision History ........................................................................................................................... 2
1
2
TMS320VC5416 Features....................................................................................................... 9
Introduction....................................................................................................................... 10
2.1
Description .................................................................................................................. 10
Pin Assignments............................................................................................................ 10
2.2
2.2.1
2.2.2
2.2.3
Terminal Assignments for the GGU Package ............................................................... 10
Pin Assignments for the PGE Package ...................................................................... 12
Signal Descriptions.............................................................................................. 13
3
Functional Overview ........................................................................................................... 16
3.1
Memory ...................................................................................................................... 16
3.1.1
3.1.2
3.1.3
Data Memory..................................................................................................... 16
Program Memory ................................................................................................ 18
Extended Program Memory ................................................................................... 18
3.2
3.3
3.4
3.5
On-Chip ROM With Bootloader........................................................................................... 18
On-Chip RAM............................................................................................................... 19
On-Chip Memory Security................................................................................................. 19
Memory Map ................................................................................................................ 20
3.5.1
Relocatable Interrupt Vector Table............................................................................ 21
3.6
On-Chip Peripherals ....................................................................................................... 23
3.6.1
3.6.2
3.6.3
Software-Programmable Wait-State Generator ............................................................. 23
Programmable Bank-Switching................................................................................ 25
Bus Holders ...................................................................................................... 26
3.7
Parallel I/O Ports ........................................................................................................... 26
3.7.1
3.7.2
Enhanced 8-/16-Bit Host-Port Interface (HPI8/16) .......................................................... 27
HPI Nonmultiplexed Mode...................................................................................... 28
3.8
3.9
Multichannel Buffered Serial Ports (McBSPs).......................................................................... 30
Hardware Timer ............................................................................................................ 32
3.10 Clock Generator ............................................................................................................ 32
3.11 Enhanced External Parallel Interface (XIO2) ........................................................................... 34
3.12 DMA Controller ............................................................................................................. 37
3.12.1 Features .......................................................................................................... 37
3.12.2 DMA External Access........................................................................................... 37
3.12.3 DMA Memory Maps ............................................................................................. 39
3.12.4 DMA Priority Level............................................................................................... 40
3.12.5 DMA Source/Destination Address Modification ............................................................. 40
3.12.6 DMA in Autoinitialization Mode ................................................................................ 41
3.12.7 DMA Transfer Counting......................................................................................... 41
3.12.8 DMA Transfer in Doubleword Mode .......................................................................... 42
3.12.9 DMA Channel Index Registers................................................................................. 42
3.12.10 DMA Interrupts.................................................................................................. 42
3.12.11 DMA Controller Synchronization Events .................................................................... 42
3.13 General-Purpose I/O Pins................................................................................................. 43
3.13.1 McBSP Pins as General-Purpose I/O......................................................................... 43
3.13.2 HPI Data Pins as General-Purpose I/O ...................................................................... 44
3.14 Device ID Register ......................................................................................................... 44
3.15 Memory-Mapped Registers ............................................................................................... 45
3.16 McBSP Control Registers and Subaddresses.......................................................................... 47
3.17 DMA Subbank Addressed Registers .................................................................................... 48
3.18 Interrupts .................................................................................................................... 50
Contents
3
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
4
5
Support............................................................................................................................. 51
4.1
Documentation Support ................................................................................................... 51
4.2
Device and Development-Support Tool Nomenclature................................................................ 52
Electrical Specifications...................................................................................................... 53
5.1
5.2
5.3
Absolute Maximum Ratings............................................................................................... 53
Recommended Operating Conditions ................................................................................... 53
Electrical Characteristics ................................................................................................. 54
5.3.1
Test Loading ..................................................................................................... 54
5.3.2 Timing Parameter Symbology ............................................................................................ 55
5.3.3 Internal Oscillator With External Crystal................................................................................. 56
5.4
Clock Options............................................................................................................... 57
5.4.1
Divide-By-Two and Divide-By-Four Clock Options.......................................................... 57
Multiply-By-N Clock Option (PLL Enabled)................................................................... 59
5.4.2
5.5
Memory and Parallel I/O Interface Timing .............................................................................. 60
5.5.1
5.5.2
5.5.3
5.5.4
Memory Read .................................................................................................... 60
Memory Write .................................................................................................... 63
I/O Read .......................................................................................................... 64
I/O Write .......................................................................................................... 65
5.5.5 Ready Timing for Externally Generated Wait States .................................................................. 67
5.5.6 HOLD and HOLDA Timings............................................................................................... 72
5.5.7 Reset, BIO, Interrupt, and MP/MC Timings............................................................................. 74
5.5.8 Instruction Acquisition (IAQ) and Interrupt Acknowledge (IACK) Timings .......................................... 76
5.5.9 External Flag (XF) and TOUT Timings .................................................................................. 77
5.5.10 Multichannel Buffered Serial Port (McBSP) Timing .................................................................. 78
5.5.10.1 McBSP Transmit and Receive Timings.................................................................... 78
5.5.10.2 McBSP General-Purpose I/O Timing ...................................................................... 81
5.5.10.3 McBSP as SPI Master or Slave Timing.................................................................... 82
5.5.11 Host-Port Interface Timing............................................................................................... 86
5.5.11.1 HPI8 Mode..................................................................................................... 86
5.5.11.2 HPI16 Mode ................................................................................................... 90
Mechanical Data................................................................................................................. 93
6
6.1
Package Thermal Resistance Characteristics.......................................................................... 93
4
Contents
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
List of Figures
2-1
144-Ball GGU MicroStar BGA™ (Bottom View) ............................................................................. 10
144-Pin PGE Low-Profile Quad Flatpack (Top View)....................................................................... 12
TMS320VC5416 Functional Block Diagram.................................................................................. 16
Program and Data Memory Map................................................................................................ 20
Extended Program Memory Map ............................................................................................... 21
Process Mode Status Register .................................................................................................. 22
Software Wait-State Register (SWWSR) [Memory-Mapped Register (MMR) Address 0028h]......................... 23
Software Wait-State Register (SWWSR) [Memory-Mapped Register (MMR) Address 0028h]......................... 24
Bank-Switching Control Register BSCR)[MMR Address 0029h] ........................................................... 25
Host-Port Interface — Nonmulltiplexed Mode................................................................................. 28
HPI Memory Map ................................................................................................................. 29
Multichannel Control Register (MCR1)......................................................................................... 31
Multichannel Control Register (MCR2)......................................................................................... 31
Pin Control Register (PCR) ...................................................................................................... 32
Nonconsecutive Memory Read and I/O Read Bus Sequence............................................................. 34
Consecutive Memory Read Bus Sequence (n = 3 reads).................................................................. 35
Memory Write and I/O Write Bus Sequence ................................................................................. 36
DMA Transfer Mode Control Register (DMMCRn) ........................................................................... 37
On-Chip DMA Memory Map for Program Space (DLAXS = 0 and SLAXS = 0)......................................... 39
On-Chip DMA Memory Map for Data and IO Space (DLAXS = 0 and SLAXS = 0) .................................... 40
DMPREC Register ................................................................................................................ 41
General-Purpose I/O Control Register (GPIOCR) [MMR Address 003Ch]................................................ 44
General-Purpose I/O Status Register (GPIOSR) [MMR Address 003Dh] ................................................. 44
Device ID Register (CSIDR) [MMR Address 003Eh] ......................................................................... 44
IFR and IMR Registers ........................................................................................................... 50
Tester Pin Electronics ............................................................................................................ 54
Internal Divide-By-Two Clock Option With External Crystal ............................................................... 56
External Divide-By-Two Clock Timing......................................................................................... 58
Multiply-By-One Clock Timing.................................................................................................. 59
Nonconsecutive Mode Memory Reads ....................................................................................... 61
Consecutive Mode Memory Reads............................................................................................ 62
Memory Write (MSTRB = 0).................................................................................................... 63
Parallel I/O Port Read (IOSTRB = 0) ......................................................................................... 65
Parallel I/O Port Write (IOSTRB = 0).......................................................................................... 66
Memory Read With Externally Generated Wait States ..................................................................... 68
Memory Write With Externally Generated Wait States ..................................................................... 69
I/O Read With Externally Generated Wait States ........................................................................... 70
I/O Write With Externally Generated Wait States ........................................................................... 71
HOLD and HOLDA Timings (HM = 1)......................................................................................... 73
2-2
3-1
3-2
3-3
3-4
3-5
3-6
3-7
3-8
3-9
3-10
3-11
3-12
3-13
3-14
3-15
3-16
3-17
3-18
3-19
3-20
3-21
3-22
3-23
5-1
5-2
5-3
5-4
5-5
5-6
5-7
5-8
5-9
5-10
5-11
5-12
5-13
5-14
List of Figures
5
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
5-15
5-16
5-17
5-18
5-19
5-20
5-21
5-22
5-23
5-24
5-25
5-26
5-27
5-28
5-29
5-30
5-31
5-32
5-33
5-34
Reset and BIO Timings ......................................................................................................... 74
Interrupt Timing .................................................................................................................. 75
MP/MC Timing ................................................................................................................... 75
Instruction Acquisition (IAQ) and Interrupt Acknowledge (IACK) Timings................................................ 76
External Flag (XF) Timing ...................................................................................................... 77
TOUT Timing ..................................................................................................................... 77
McBSP Receive Timings ....................................................................................................... 79
McBSP Transmit Timings....................................................................................................... 80
McBSP General-Purpose I/O Timings ........................................................................................ 81
McBSP Timing as SPI Master or Slave: CLKSTP = 10b, CLKXP = 0.................................................... 82
McBSP Timing as SPI Master or Slave: CLKSTP = 11b, CLKXP = 0.................................................... 83
McBSP Timing as SPI Master or Slave: CLKSTP = 10b, CLKXP = 1.................................................... 84
McBSP Timing as SPI Master or Slave: CLKSTP = 11b, CLKXP = 1.................................................... 85
Using HDS to Control Accesses (HCS Always Low)........................................................................ 88
Using HCS to Control Accesses ............................................................................................... 89
HINT Timing ...................................................................................................................... 89
GPIOx Timings................................................................................................................... 89
Nonmultiplexed Read Timings ................................................................................................. 91
Nonmultiplexed Write Timings ................................................................................................. 92
HRDY Relative to CLKOUT .................................................................................................... 92
6
List of Figures
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
List of Tables
2-1
Terminal Assignments for the TMS320VC5416GGU (144-Pin BGA Package) ......................................... 11
Signal Descriptions ............................................................................................................... 13
Standard On-Chip ROM Layout ............................................................................................... 19
Processor Mode Status (PMST) Register Bit Fields ........................................................................ 22
Software Wait-State Register (SWWSR) Bit Fields ......................................................................... 24
Software Wait-State Control Register (SWCR) Bit Fields .................................................................. 24
Bank-Switching Control Register (BSCR) Fields.............................................................................. 25
Bus Holder Control Bits .......................................................................................................... 26
Sample Rate Input Clock Selection ........................................................................................... 32
Clock Mode Settings at Reset ................................................................................................. 33
DMD Section of the DMMCRn Register ...................................................................................... 38
DMA Reload Register Selection ............................................................................................... 41
DMA Interrupts ................................................................................................................... 42
DMA Synchronization Events .................................................................................................. 42
DMA Channel Interrupt Selection.............................................................................................. 43
Device ID Register (CSIDR) Bits................................................................................................ 45
CPU Memory-Mapped Registers................................................................................................ 45
Peripheral Memory-Mapped Registers for Each DSP Subsystem ........................................................ 46
McBSP Control Registers and Subaddresses................................................................................. 47
DMA Subbank Addressed Registers ........................................................................................... 48
Interrupt Locations and Priorities................................................................................................ 50
Input Clock Frequency Characteristics......................................................................................... 56
Clock Mode Pin Settings for the Divide-By-2 and By Divide-By-4 Clock Options....................................... 57
Divide-By-2 and Divide-By-4 Clock Options Timing Requirements ....................................................... 57
Divide-By-2 and Divide-By-4 Clock Options Switching Characteristics................................................... 57
Multiply-By-N Clock Option Timing Requirements .......................................................................... 59
Multiply-By-N Clock Option Switching Characteristics...................................................................... 59
Memory Read Timing Requirements.......................................................................................... 60
Memory Read Switching Characteristics ..................................................................................... 60
Memory Write Switching Characteristics ..................................................................................... 63
I/O Read Timing Requirements................................................................................................ 64
I/O Read Switching Characteristics ........................................................................................... 64
I/O Write Switching Characteristics............................................................................................ 65
Ready Timing Requirements for Externally Generated Wait States ...................................................... 67
Ready Switching Characteristics for Externally Generated Wait States.................................................. 67
HOLD and HOLDA Timing Requirements.................................................................................... 72
HOLD and HOLDA Switching Characteristics ............................................................................... 72
Reset, BIO, Interrupt, and MP/MC Timing Requirements .................................................................. 74
Instruction Acquisition (IAQ) and Interrupt Acknowledge (IACK) Switching Characteristics........................... 76
2-2
3-1
3-2
3-3
3-4
3-5
3-6
3-7
3-8
3-9
3-10
3-11
3-12
3-13
3-14
3-15
3-16
3-17
3-18
3-19
5-1
5-2
5-3
5-4
5-5
5-6
5-7
5-8
5-9
5-10
5-11
5-12
5-13
5-14
5-15
5-16
5-17
5-18
List of Tables
7
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
5-19
5-20
5-21
5-22
5-23
5-24
5-25
5-26
5-27
5-28
5-29
5-30
5-31
5-32
5-33
5-34
5-35
6-1
External Flag (XF) and TOUT Switching Characteristics................................................................... 77
McBSP Transmit and Receive Timing Requirements....................................................................... 78
McBSP Transmit and Receive Switching Characteristics .................................................................. 79
McBSP General-Purpose I/O Timing Requirements ........................................................................ 81
McBSP General-Purpose I/O Switching Characteristics ................................................................... 81
McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 10b, CLKXP = 0) ................................. 82
McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 10b, CLKXP = 0)............................. 82
McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 11b, CLKXP = 0) ................................. 83
McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 11b, CLKXP = 0)............................. 83
McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 10b, CLKXP = 1) ................................. 84
McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 10b, CLKXP = 1)............................. 84
McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 11b, CLKXP = 1) ................................. 85
McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 11b, CLKXP = 1)............................. 85
HPI8 Mode Timing Requirements ............................................................................................. 86
HPI8 Mode Switching Characteristics .......................................................................................... 87
HPI16 Mode Timing Requirements............................................................................................ 90
HPI16 Mode Switching Characteristics ....................................................................................... 91
Thermal Resistance Characteristics............................................................................................ 93
8
List of Tables
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
1
•
TMS320VC5416 Features
Advanced Multibus Architecture With Three
Separate 16-Bit Data Memory Buses and One
Program Memory Bus
•
Arithmetic Instructions With Parallel Store and
Parallel Load
•
•
•
Conditional Store Instructions
Fast Return From Interrupt
On-Chip Peripherals
•
•
40-Bit Arithmetic Logic Unit (ALU) Including a
40-Bit Barrel Shifter and Two Independent
40-Bit Accumulators
–
Software-Programmable Wait-State
Generator and Programmable
Bank-Switching
17- × 17-Bit Parallel Multiplier Coupled to a
40-Bit Dedicated Adder for Non-Pipelined
Single-Cycle Multiply/Accumulate (MAC)
Operation
–
On-Chip Programmable Phase-Locked
Loop (PLL) Clock Generator With External
Clock Source
•
•
Compare, Select, and Store Unit (CSSU) for the
Add/Compare Selection of the Viterbi Operator
–
–
One 16-Bit Timer
Six-Channel Direct Memory Access (DMA)
Controller
Exponent Encoder to Compute an Exponent
Value of a 40-Bit Accumulator Value in a
Single Cycle
–
–
Three Multichannel Buffered Serial Ports
(McBSPs)
8/16-Bit Enhanced Parallel Host-Port
Interface (HPI8/16)
•
Two Address Generators With Eight Auxiliary
Registers and Two Auxiliary Register
Arithmetic Units (ARAUs)
•
Power Consumption Control With IDLE1,
IDLE2, and IDLE3 Instructions With
Power-Down Modes
•
•
Data Bus With a Bus Holder Feature
Extended Addressing Mode for 8M × 16-Bit
Maximum Addressable External Program
Space
•
•
CLKOUT Off Control to Disable CLKOUT
On-Chip Scan-Based Emulation Logic, IEEE
Std 1149.1 (JTAG) Boundary Scan Logic(1)
•
128K x 16-Bit On-Chip RAM Composed of:
–
Eight Blocks of 8K × 16-Bit On-Chip
Dual-Access Program/Data RAM
Eight Blocks of 8K × 16-Bit On-Chip
Single-Access Program RAM
•
•
144-Pin Ball Grid Array (BGA)(GGU Suffix)
144-Pin Low-Profile Quad Flatpack
(LQFP)(PGE Suffix)
–
•
•
6.25-ns Single-Cycle Fixed-Point Instruction
Execution Time (160 MIPS)
•
16K × 16-Bit On-Chip ROM Configured for
Program Memory
8.33-ns Single-Cycle Fixed-Point Instruction
Execution Time (120 MIPS)
•
•
Enhanced External Parallel Interface (XIO2)
Single-Instruction-Repeat and Block-Repeat
Operations for Program Code
•
•
•
3.3-V I/O Supply Voltage (160 and 120 MIPS)
1.6-V Core Supply Voltage (160 MIPS)
1.5-V Core Supply Voltage (120 MIPS)
•
Block-Memory-Move Instructions for Better
Program and Data Management
•
•
Instructions With a 32-Bit Long Word Operand
Instructions With Two- or Three-Operand
Reads
(1) IEEE Standard 1149.1-1990 Standard-Test-Access Port and
Boundary Scan Architecture
TMS320C54x, TMS320 are trademarks of Texas Instruments.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 1999–2005, Texas Instruments Incorporated
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
2
Introduction
This section describes the main features of the TMS320VC5416, lists the pin assignments, and describes
the function of each pin. This data manual also provides a detailed description section, electrical
specifications, parameter measurement information, and mechanical data about the available packaging.
NOTE
This data manual is designed to be used in conjunction with the TMS320C54x™ DSP
Functional Overview (literature number SPRU307).
2.1 Description
The TMS320VC5416 fixed-point, digital signal processor (DSP) (hereafter referred to as the device unless
otherwise specified) is based on an advanced modified Harvard architecture that has one program
memory bus and three data memory buses. This processor provides an arithmetic logic unit (ALU) with a
high degree of parallelism, application-specific hardware logic, on-chip memory, and additional on-chip
peripherals. The basis of the operational flexibility and speed of this DSP is a highly specialized instruction
set.
Separate program and data spaces allow simultaneous access to program instructions and data, providing
a high degree of parallelism. Two read operations and one write operation can be performed in a single
cycle. Instructions with parallel store and application-specific instructions can fully utilize this architecture.
In addition, data can be transferred between data and program spaces. Such parallelism supports a
powerful set of arithmetic, logic, and bit-manipulation operations that can all be performed in a single
machine cycle. The device also includes the control mechanisms to manage interrupts, repeated
operations, and function calls.
2.2 Pin Assignments
Figure 2-1 illustrates the ball locations for the 144-pin ball grid array (BGA) package and is used in
conjunction with Table 2-1 to locate signal names and ball grid numbers. Figure 2-2 provides the pin
assignments for the 144-pin low-profile quad flatpack (LQFP) package.
2.2.1 Terminal Assignments for the GGU Package
13 12 11 10
9
8
7
6
5
4
3
2
1
A
B
C
D
E
F
G
H
J
K
L
M
N
Figure 2-1. 144-Ball GGU MicroStar BGA™ (Bottom View)
10
Introduction
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
Table 2-1 lists each signal name and BGA ball number for the 144-pin TMS320VC5416GGU package.
Table 2-2 lists each terminal name, terminal function, and operating modes for the TMS320VC5416. In
Table 2-1, DVDD is the power supply for the I/O pins while CVDD is the power supply for the core CPU.
Table 2-1. Terminal Assignments for the TMS320VC5416GGU (144-Pin BGA Package)
SIGNAL
QUADRANT 1
SIGNAL
QUADRANT 2
SIGNAL
QUADRANT 3
SIGNAL
QUADRANT 4
BGA BALL #
BGA BALL #
BGA BALL #
BGA BALL #
CVSS
A22
A1
B1
C2
C1
D4
D3
D2
D1
E4
E3
E2
E1
F4
F3
F2
F1
G2
G1
G3
G4
H1
H2
H3
H4
J1
BFSX1
BDX1
DVDD
DVSS
CLKMD1
CLKMD2
CLKMD3
HPI16
HD2
N13
M13
L12
L13
K10
K11
K12
K13
J10
CVSS
BCLKR1
HCNTL0
DVSS
N1
N2
M3
N3
K4
A19
A20
CVSS
DVDD
D6
A13
A12
B11
A11
D10
C10
B10
A10
D9
C9
B9
CVSS
DVDD
A10
BCLKR0
BCLKR2
BFSR0
BFSR2
BDR0
HCNTL1
BDR2
BCLKX0
BCLKX2
CVSS
HD7
L4
D7
A11
M4
N4
K5
D8
A12
D9
A13
D10
D11
D12
HD4
D13
D14
D15
HD5
CVDD
CVSS
HDS1
DVSS
HDS2
DVDD
A0
A14
TOUT
EMU0
EMU1/OFF
TDO
J11
L5
A15
J12
M5
N5
K6
CVDD
HAS
J13
A9
H10
H11
H12
H13
G12
G13
G11
G10
F13
F12
F11
F10
E13
E12
E11
E10
D13
D12
D11
C13
C12
C11
B13
B12
D8
C8
B8
DVSS
CVSS
CVDD
HCS
HR/W
READY
PS
TDI
L6
TRST
TCK
HINT
M6
N6
M7
N7
L7
CVDD
A8
TMS
BFSX0
BFSX2
HRDY
DVDD
B7
CVSS
CVDD
HPIENA
DVSS
CLKOUT
HD3
A7
C7
D7
A6
K7
DS
DVSS
N8
M8
L8
IS
HD0
B6
R/W
BDX0
BDX2
IACK
C6
D6
A5
MSTRB
IOSTRB
MSC
XF
X1
K8
A1
X2/CLKIN
RS
N9
M9
L9
A2
J2
HBIL
A3
B5
J3
D0
NMI
HD6
A4
C5
D5
A4
HOLDA
IAQ
J4
D1
INT0
K9
K1
K2
K3
L1
D2
INT1
N10
M10
L10
N11
M11
L11
N12
M12
A5
HOLD
BIO
D3
INT2
A6
B4
D4
INT3
A7
C4
A3
MP/MC
DVDD
CVSS
BDR1
BFSR1
D5
CVDD
A8
L2
A16
HD1
A9
B3
L3
DVSS
A17
CVSS
CVDD
A21
DVSS
C3
A2
M1
M2
BCLKX1
DVSS
A18
B2
Introduction
11
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
2.2.2 Pin Assignments for the PGE Package
The TMS320VC5416PGE 144-pin low-profile quad flatpack (LQFP) pin assignments are shown in
Figure 2-2. DVDD is the power supply for the I/O pins while CVDD is the power supply for the core CPU.
VSS is the ground for both the I/O pins and the core CPU.
CV
A22
SS
A18
A17
DV
A16
D5
D4
D3
D2
D1
D0
RS
X2/CLKIN
X1
HD3
CLKOUT
DV
SS
HPIENA
CV
DD
CV
SS
1
108
107
106
105
104
103
102
101
100
99
2
CV
SS
3
SS
DV
DD
4
A10
HD7
A11
A12
A13
A14
A15
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
98
CV
DD
97
HAS
96
DV
SS
SS
DD
95
CV
CV
94
93
HCS
HR/W
READY
PS
92
91
90
TMS
TCK
TRST
89
DS
88
IS
87
R/W
86 TDI
85 TDO
EMU1/OFF
83 EMU0
82 TOUT
HD2
80 HPI16
79 CLKMD3
MSTRB
IOSTRB
MSC
XF
HOLDA
IAQ
HOLD
BIO
MP/MC
84
81
78
77
76
75
74
73
CLKMD2
CLKMD1
DV
DD
DV
DV
SS
CV
SS
DD
BDR1
BFSR1
BDX1
BFSX1
Figure 2-2. 144-Pin PGE Low-Profile Quad Flatpack (Top View)
12
Introduction
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
2.2.3 Signal Descriptions
Table 2-2 lists each signal, function, and operating mode(s) grouped by function.
Table 2-2. Signal Descriptions
TERMINAL
NAME
I/O(1)
DESCRIPTION
DATA SIGNALS
A22 (MSB),
A21, A20,
A19, A18,
A17, A16,
A15, A14,
A13, A12,
A11, A10, A9,
A8, A7, A6,
A5, A4, A3,
A2, A1,
I/O/Z(2)(3) Parallel address bus A22 [most significant bit (MSB)] through A0 [least significant bit (LSB)]. The sixteen LSB
lines, A0 to A15, are multiplexed to address external memory (program, data) or I/O. The seven MSB lines, A16
to A22, address external program space memory. A22-A0 is placed in the high-impedance state in the hold
mode. A22-A0 also goes into the high-impedance state when OFF is low.A17-A0 are inputs in HPI16 mode.
These pins can be used to address internal memory via the host-port interface (HPI) when the HPI16 pin is high.
These pins also have Schmitt trigger inputs.The address bus has a bus holder feature that eliminates passive
components and the power dissipation associated with them. The bus holder keeps the address bus at the
previous logic level when the bus goes into a high-impedance state.
A0 (LSB)
D15 (MSB),
D14, D13,
D12, D11,
D10, D9, D8,
D7, D6, D5,
D4, D3, D2,
D1, D0 (LSB)
I/O/Z(2)(3) Parallel data bus D15 (MSB) through D0 (LSB). D15-D0 is multiplexed to transfer data between the core CPU
and external data/program memory or I/O devices or HPI in HPI16 mode (when HPI16 pin is high). D15-D0 is
placed in the high-impedance state when not outputting data or when RS or HOLD is asserted. D15-D0 also
goes into the high-impedance state when OFF is low. These pins also have Schmitt trigger inputs.The data bus
has a bus holder feature that eliminates passive components and the power dissipation associated with them.
The bus holder keeps the data bus at the previous logic level when the bus goes into the high-impedance state.
The bus holders on the data bus can be enabled/disabled under software control.
INITIALIZATION, INTERRUPT AND RESET OPERATIONS
Interrupt acknowledge signal. IACK indicates receipt of an interrupt and that the program counter is fetching the
interrupt vector location designated by A15-A0. IACK also goes into the high-impedance state when OFF is low.
IACK
O/Z
(2)
INT0
INT1
INT2
INT3
(2)
External user interrupt inputs. INT0-INT3 are maskable and are prioritized by the interrupt mask register (IMR)
and the interrupt mode bit. INT0 -INT3 can be polled and reset by way of the interrupt flag register (IFR).
I
(2)
(2)
Nonmaskable interrupt. NMI is an external interrupt that cannot be masked by way of the INTM or the IMR.
When NMI is activated, the processor traps to the appropriate vector location.
(2)
NMI
I
Reset. RS causes the digital signal processor (DSP) to terminate execution and forces the program counter to
0FF80h. When RS is brought to a high level, execution begins at location 0FF80h of program memory. RS
affects various registers and status bits.
(2)
RS
I
I
Microprocessor/microcomputer mode select. If active low at reset, microcomputer mode is selected, and the
internal program ROM is mapped into the upper 16K words of program memory space. If the pin is driven high
during reset, microprocessor mode is selected, and the on-chip ROM is removed from program space. This pin
is only sampled at reset, and the MP/MC bit of the processor mode status (PMST) register can override the
mode that is selected at reset.
MP/MC
MULTIPROCESSING SIGNALS
Branch control. A branch can be conditionally executed when BIO is active. If low, the processor executes the
conditional instruction. The BIO condition is sampled during the decode phase of the pipeline for the XC
instruction, and all other instructions sample BIO during the read phase of the pipeline.
(2)
BIO
I
External flag output (latched software-programmable signal). XF is set high by the SSBX XF instruction, set low
by RSBX XF instruction or by loading ST1. XF is used for signaling other processors in multiprocessor
configurations or used as a general-purpose output pin. XF goes into the high-impedance state when OFF is
low, and is set high at reset.
XF
O/Z
MEMORY CONTROL SIGNALS
Data, program, and I/O space select signals. DS, PS, and IS are always high unless driven low for
communicating to a particular external space. Active period corresponds to valid address information. DS, PS,
and IS are placed into the high-impedance state in the hold mode; these signals also go into the high-impedance
state when OFF is low.
DS
PS
IS
O/Z
O/Z
Memory strobe signal. MSTRB is always high unless low-level asserted to indicate an external bus access to
data or program memory. MSTRB is placed in the high-impedance state in the hold mode; it also goes into the
high-impedance state when OFF is low.
MSTRB
(1) I = Input, O = Output, Z = High-impedance, S = Supply
(2) These pins have Schmitt trigger inputs.
(3) This pin has an internal bus holder controlled by way of the BSCR register.
Introduction
13
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
Table 2-2. Signal Descriptions (continued)
TERMINAL
NAME
I/O(1)
DESCRIPTION
Data ready. READY indicates that an external device is prepared for a bus transaction to be completed. If the
device is not ready (READY is low), the processor waits one cycle and checks READY again. Note that the
processor performs ready detection if at least two software wait states are programmed. The READY signal is
not sampled until the completion of the software wait states.
READY
R/W
I
Read/write signal. R/W indicates transfer direction during communication to an external device. R/W is normally
in the read mode (high), unless it is asserted low when the DSP performs a write operation. R/W is placed in the
high-impedance state in the hold mode; and it also goes into the high-impedance state when OFF is low.
O/Z
I/O strobe signal. IOSTRB is always high unless low-level asserted to indicate an external bus access to an I/O
device. IOSTRB is placed in the high-impedance state in the hold mode; it also goes into the high-impedance
state when OFF is low.
IOSTRB
HOLD
O/Z
I
Hold input. HOLD is asserted to request control of the address, data, and control lines. When acknowledged by
the device, these lines go into the high-impedance state.
Hold acknowledge. HOLDA indicates to the external circuitry that the processor is in a hold state and that the
address, data, and control lines are in the high-impedance state, allowing them to be available to the external
circuitry. HOLDA also goes into the high-impedance state when OFF is low. Figure 2-2 This pin is driven high
during reset.
HOLDA
O/Z
Microstate complete. MSC indicates completion of all software wait states. When two or more software wait
states are enabled, the MSC pin goes active at the beginning of the first software wait state and goes inactive
high at the beginning of the last software wait state. If connected to the READY input, MSC forces one external
wait state after the last internal wait state is completed. MSC also goes into the high-impedance state when OFF
is low.
MSC
IAQ
O/Z
O/Z
Instruction acquisition signal. IAQ is asserted (active low) when there is an instruction address on the address
bus and goes into the high-impedance state when OFF is low.
TIMER SIGNALS
Clock output signal. CLKOUT can represent the machine-cycle rate of the CPU divided by 1, 2, 3, or 4 as
configured in the bank-switching control register (BSCR). Following reset, CLKOUT represents the ma-
chine-cycle rate divided by 4.
CLKOUT
O/Z
I
Clock mode select signals. CLKMD1-CLKMD3 allow the selection and configuration of different clock modes
such as crystal, external clock, and PLL mode. The external CLKMD1-CLKMD3 pins are sampled to determine
the desired clock generation mode while RS is low. Following reset, the clock generation mode can be
reconfigured by writing to the internal clock mode register in software.
CLKMD1(2)
CLKMD2(2)
CLKMD3(2)
Clock/oscillator input. If the internal oscillator is not being used, X2/CLKIN functions as the clock input. (This is
revision-dependent, see Section Section 3.10 for additional information.)
X2/CLKIN(2)
X1
I
Output pin from the internal oscillator for the crystal. If the internal oscillator is not used, X1 should be left
unconnected. X1 does not go into the high-impedance state when OFF is low. (This is revision-dependent, see
Section Section 3.10 for additional information.)
O
Timer output. TOUT signals a pulse when the on-chip timer counts down past zero. The pulse is one CLKOUT
cycle wide. TOUT also goes into the high-impedance state when OFF is low.
TOUT
O/Z
MULTICHANNEL BUFFERED SERIAL PORT 0 (McBSP #0), MULTICHANNEL BUFFERED SERIAL PORT 1 (McBSP #1),AND
MULTICHANNEL BUFFERED SERIAL PORT 2 (McBSP #2) SIGNALS
BCLKR0(2)
Receive clock input. BCLKR can be configured as an input or an output; it is configured as an input following
reset. BCLKR serves as the serial shift clock for the buffered serial port receiver.
BCLKR1(2)
BCLKR2(2)
I/O/Z
I
BDR0, BDR1,
BDR2
Serial data receive input
BFSR0,
BFSR1,
BFSR2
Frame synchronization pulse for receive input. BFSR can be configured as an input or an output; it is configured
as an input following reset. The BFSR pulse initiates the receive data process over BDR.
I/O/Z
BCLKX0(2)
BCLKX1(2)
BCLKX2(2)
Transmit clock. BCLKX serves as the serial shift clock for the McBSP transmitter. BCLKX can be configured as
an input or an output, and is configured as an input following reset. BCLKX enters the high-impedance state
when OFF goes low.
I/O/Z
O/Z
BDX0, BDX1,
BDX2
Serial data transmit output. BDX is placed in the high-impedance state when not transmitting, when RS is
asserted, or when OFF is low.
BFSX0,
BFSX1,
BFSX2
Frame synchronization pulse for transmit input/output. The BFSX pulse initiates the data transmit process over
BDX. BFSX can be configured as an input or an output, and is configured as an input following reset. BFSX
goes into the high-impedance state when OFF is low.
I/O/Z
14
Introduction
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
Table 2-2. Signal Descriptions (continued)
TERMINAL
NAME
I/O(1)
DESCRIPTION
HOST-PORT INTERFACE SIGNALS
Parallel bidirectional data bus. The HPI data bus is used by a host device bus to exchange information with the
HPI registers. These pins can also be used as general-purpose I/O pins. HD0-HD7 is placed in the
HD0-
high-impedance state when not outputting data or when OFF is low. The HPI data bus includes bus holders to
reduce the static power dissipation caused by floating, unused pins. When the HPI data bus is not being driven
by the device, the bus holders keep the pins at the previous logic level. The HPI data bus holders are disabled
at reset and can be enabled/disabled via the HBH bit of the BSCR. These pins also have Schmitt trigger inputs.
I/O/Z
HD7(2)(3)
HCNTL0(4)
HCNTL1(4)
Control inputs. HCNTL0 and HCNTL1 select a host access to one of the three HPI registers. The control inputs
have internal pullups that are only enabled when HPIENA = 0. These pins are not used when HPI16 = 1.
I
Byte identification. HBIL identifies the first or second byte of transfer. The HPIL input has an internal pullup
resistor that is only enabled when HPIENA = 0. This pin is not used when HPI16 = 1.
HBIL(4)
I
Chip select. HCS is the select input for the HPI and must be driven low during accesses. The chip select input
has an internal pullup resistor that is only enabled when HPIENA = 0.
(2) (4)
HCS
I
(2) (4)
HDS1
HDS2
Data strobe. HDS1 and HDS2 are driven by the host read and write strobes to control the transfer. The strobe
inputs have internal pullup resistors that are only enabled when HPIENA = 0.
I
I
(2) (4)
Address strobe. Host with multiplexed address and data pins requires HAS to latch the address in the HPIA
register. HAS input has an internal pullup resistor that is only enabled when HPIENA = 0.
(2) (4)
HAS
Read/write. HR/W controls the direction of the HPI transfer. HR/W has an internal pullup resistor that is only
enabled when HPIENA = 0.
HR/W(4)
HRDY
HINT
I
Ready output. HRDY goes into the high-impedance state when OFF is low. The ready output informs the host
when the HPI is ready for the next transfer. This pin is driven high during reset.
O/Z
O/Z
Interrupt output. This output is used to interrupt the host. When the DSP is in reset, HINT is driven high. HINT
goes into the high-impedance state when OFF is low. This pin is not used when HPI16 = 1.
HPI module select. HPIENA must be tied to DVDD to have HPI selected. If HPIENA is left open or connected to
ground, the HPI module is not selected, internal pullup for the HPI input pins are enabled, and the HPI data bus
has holders set. HPIENA is provided with an internal pulldown resistor that is always active. HPIENA is sampled
when RS goes high and is ignored until RS goes low again. This pin should never be changed while reset is
high.
HPIENA(5)
HPI16(5)
I
I
HPI16 mode selection. This pin must be tied to DVDD to enable HPI16 mode. The pin has an internal pulldown
resistor which is always active. If HPI16 is left open or driven low, the HPI16 mode is disabled.
SUPPLY PINS
Ground. Dedicated ground for the core CPU
+VDD. Dedicated power supply for the core CPU
Ground. Dedicated ground for I/O pins
+VDD. Dedicated power supply for I/O pins
TEST PINS
CVSS
CVDD
DVSS
DVDD
S
S
S
S
IEEE standard 1149.1 test clock. TCK is normally a free-running clock signal with a 50% duty cycle. The
changes on test access port (TAP) of input signals TMS and TDI are clocked into the TAP controller, instruction
register, or selected test data register on the rising edge of TCK. Changes at the TAP output signal (TDO) occur
on the falling edge of TCK.
TCK(2)(4)
I
IEEE standard 1149.1 test data input. Pin with internal pullup device. TDI is clocked into the selected register
(instruction or data) on a rising edge of TCK.
TDI(4)
TDO
I
IEEE standard 1149.1 test data output. The contents of the selected register (instruction or data) are shifted out
of TDO on the falling edge of TCK. TDO is in the high-impedance state except when the scanning of data is in
progress. TDO also goes into the high-impedance state when OFF is low.
O/Z
IEEE standard 1149.1 test mode select. Pin with internal pullup device. This serial control input is clocked into
the TAP controller on the rising edge of TCK.
TMS(4)
I
I
IEEE standard 1149.1 test reset. TRST, when high, gives the IEEE standard 1149.1 scan system control of the
operations of the device. If TRST is not connected or driven low, the device operates in its functional mode, and
the IEEE standard 1149.1 signals are ignored. Pin with internal pulldown device.
(5)
TRST
Emulator 0 pin. When TRST is driven low, EMU0 must be high for activation of the OFF condition. When TRST
is driven high, EMU0 is used as an interrupt to or from the emulator system and is defined as input/output by
way of the IEEE standard 1149.1 scan system.
EMU0(6)
I/O/Z
(4) This pin has an internal pullup resistor.
(5) This pin has an internal pulldown resistor.
(6) This pin must be pulled up with a 4.7-kΩ resistor to ensure the device is operable in functional mode or emulation mode.
Introduction
15
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
Table 2-2. Signal Descriptions (continued)
TERMINAL
NAME
I/O(1)
DESCRIPTION
Emulator 1 pin/disable all outputs. When TRST is driven high, EMU1/OFF is used as an interrupt to or from the
emulator system and is defined as input/output by way of IEEE standard 1149.1 scan system. When TRST is
driven low, EMU1/OFF is configured as OFF. The EMU1/OFF signal, when active low, puts all output drivers into
the high-impedance state. Note that OFF is used exclusively for testing and emulation purposes (not for
multiprocessing applications). Therefore, for the OFF condition, the following apply:
TRST = low,
EMU1/OFF(6)
I/O/Z
EMU0 = high
EMU1/OFF = low
3
Functional Overview
The following functional overview is based on the block diagram in Figure 3-1.
P, C, D, E Buses and Control Signals
64K RAM
Dual Access
Program/Data
64K RAM
Single Access
Program
16K Program
ROM
54X cLEAD
MBus
GPIO
RHEA
Bridge
TI BUS
RHEA Bus
McBSP1
XIO
Enhanced XIO
McBSP2
McBSP3
16HPI
16 HPI
xDMA
logic
RHEAbus
TIMER
APLL
JTAG
Clocks
Figure 3-1. TMS320VC5416 Functional Block Diagram
3.1 Memory
The device provides both on-chip ROM and RAM memories to aid in system performance and integration.
3.1.1 Data Memory
The data memory space addresses up to 64K of 16-bit words. The device automatically accesses the
on-chip RAM when addressing within its bounds. When an address is generated outside the RAM bounds,
the device automatically generates an external access.
The advantages of operating from on-chip memory are as follows:
•
•
Higher performance because no wait states are required
Higher performance because of better flow within the pipeline of the central arithmetic logic unit
(CALU)
•
Lower cost than external memory
16
Functional Overview
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
•
Lower power than external memory
The advantage of operating from off-chip memory is the ability to access a larger address space.
Functional Overview
17
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
3.1.2 Program Memory
Software can configure their memory cells to reside inside or outside of the program address map. When
the cells are mapped into program space, the device automatically accesses them when their addresses
are within bounds. When the program-address generation (PAGEN) logic generates an address outside its
bounds, the device automatically generates an external access. The advantages of operating from on-chip
memory are as follows:
•
•
•
Higher performance because no wait states are required
Lower cost than external memory
Lower power than external memory
The advantage of operating from off-chip memory is the ability to access a larger address space.
3.1.3 Extended Program Memory
The device uses a paged extended memory scheme in program space to allow access of up to 8192K of
program memory. In order to implement this scheme, the device includes several features which are also
present on C548/549/5410:
•
•
•
Twenty-three address lines, instead of sixteen
An extra memory-mapped register, the XPC
Six extra instructions for addressing extended program space
Program memory in the device is organized into 128 pages that are each 64K in length.
The value of the XPC register defines the page selection. This register is memory-mapped into data space
to address 001Eh. At a hardware reset, the XPC is initialized to 0.
3.2 On-Chip ROM With Bootloader
The device features a 16K-word × 16-bit on-chip maskable ROM that can only be mapped into program
memory space.
Customers can arrange to have the ROM of the device programmed with contents unique to any particular
application.
A bootloader is available in the standard on-chip ROM. This bootloader can be used to automatically
transfer user code from an external source to anywhere in the program memory at power up. If MP/MC of
the device is sampled low during a hardware reset, execution begins at location FF80h of the on-chip
ROM. This location contains a branch instruction to the start of the bootloader program.
The standard devices provide different ways to download the code to accommodate various system
requirements:
•
•
•
•
•
Parallel from 8-bit or 16-bit-wide EPROM
Parallel from I/O space, 8-bit or 16-bit mode
Serial boot from serial ports, 8-bit or 16-bit mode
Host-port interface boot
Warm boot
18
Functional Overview
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
The standard on-chip ROM layout is shown in Table 3-1.
Table 3-1. Standard On-Chip ROM Layout
ADDRESS RANGE
C000h-D4FFh
DESCRIPTION
ROM tables for the GSM EFR speech codec
Reserved
D500h-F7FFh
F800h-FBFFh
FC00h-FCFFh
FD00h-FDFFh
FE00h-FEFFh
FF00h-FF7Fh
FF80h-FFFFh
Bootloader
µ-Law expansion table
A-Law expansion table
Sine look-up table
Reserved(1)
Interrupt vector table
(1) In the ROM, 128 words are reserved for factory device-testing purposes. Application code to be implemented in on-chip ROM must
reserve these 128 words at addresses FF00h-FF7Fh in program space.
3.3 On-Chip RAM
The device contains 64K-word × 16-bit of on-chip dual-access RAM (DARAM) and 64K-word × 16-bit of
on-chip single-access RAM (SARAM).
The DARAM is composed of eight blocks of 8K words each. Each block in the DARAM can support two
reads in one cycle, or a read and a write in one cycle. Four blocks of DARAM are located in the address
range 0080h-7FFFh in data space, and can be mapped into program/data space by setting the OVLY bit
to one. The other four blocks of DARAM are located in the address range 18000h-1FFFFh in program
space. The DARAM located in the address range 18000h-1FFFFh in program space can be mapped into
data space by setting the DROM bit to one.
The SARAM is composed of eight blocks of 8K words each. Each of these eight blocks is a single-access
memory. For example, an instruction word can be fetched from one SARAM block in the same cycle as a
data word is written to another SARAM block. The SARAM is located in the address range
28000h-2FFFFh, and 38000h-3FFFFh in program space.
3.4 On-Chip Memory Security
The device has a maskable option to protect the contents of on-chip memories.
When the RAM/ROM security option is selected, the following restrictions apply:
•
Only the on-chip ROM originating instructions can read the contents of the on-chip ROM; on-chip RAM
and external RAM originating instruction can not read data from ROM: instead 0FFFFh is read. Code
can still branch to ROM from on-chip RAM or external program memory.
•
•
The contents of on-chip RAM can be read by all instructions, even by instructions fetched from external
memory. To protect the internal RAM, the user must never branch to external memory.
The security feature completely disables the scan-based emulation capability of the 54x to prevent the
use of a debugger utility. This only affects emulation and does not prevent the use of the JTAG
boundary scan test capability.
•
•
The device is internally forced into microcomputer mode at reset (MP/MC bit forced to zero),
preventing the ROM from being disabled by the external MP/MC pin. The status of the MP/MC bit in
the PMST register can be changed after reset by the user application.
HPI writes have no restriction, but HPI reads are restricted to the 4000h - 5FFFh address range.
Functional Overview
19
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
If the ROM-only security option is selected the following restrictions apply:
•
Only the on-chip ROM originating instructions can read the contents of the on-chip ROM; on-chip RAM
and external RAM originating instruction cannot read data from ROM: instead 0FFFFh is read. Code
can still branch to ROM from on-chip RAM or external program memory.
•
•
The contents of on-chip RAM can be read by all instructions, even by instructions fetched from external
memory. To protect the internal RAM the user must never branch to external memory.
The security feature completely disables the scan-based emulation capability of the 54x to prevent the
use of a debugger utility. This only affects emulation and does not prevent the use of the JTAG
boundary scan test capability.
•
•
The device can be started in either microcomputer mode or microprocessor mode at reset (depends on
the MP/MC pin).
HPI read and writes have no restriction.
3.5 Memory Map
The program and data memory map is shown in Figure 3-2. Address ranges for on-chip DARAM in data
memory are:
•
•
•
•
•
•
•
•
DARAM0: 0080h-1FFFh
DARAM1: 2000h-3FFFh
DARAM2: 4000h-5FFFh
DARAM3: 6000h-7FFFh
DARAM4: 8000h-9FFFh
DARAM5: A000h-BFFFh
DARAM6: C000h-DFFFh
DARAM7: E000h-FFFFh
Page 0 Program
Page 0 Program
Hex
Data
Hex
Hex
0000
0000
0000
Reserved
(OVLY = 1)
External
(OVLY = 0)
Reserved
Memory-Mapped
Registers
(OVLY = 1)
External
005F
(OVLY = 0)
007F
0080
007F
0080
0060
007F
0080
Scratch-Pad
RAM
On-Chip
DARAM0−3
(OVLY = 1)
On-Chip
DARAM0−3
(OVLY = 1)
External
(OVLY = 0)
On-Chip
DARAM0−3
(32K x 16-bit)
External
(OVLY = 0)
7FFF
8000
BFFF
C000
7FFF
8000
7FFF
8000
External
External
On-Chip
DARAM4−7
(DROM=1)
or
External
(DROM=0)
On-Chip ROM
(4K x 16-bit)
FF7F
FF80
FEFF
FF00
FF7F
FF80
FFFF
Interrupts
(External)
Reserved
Interrupts
(On-Chip)
FFFF
FFFF
MP/MC= 1
(Microprocessor Mode)
MP/MC= 0
(Microcomputer Mode)
Figure 3-2. Program and Data Memory Map
20
Functional Overview
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
The extended program memory map is shown in Figure 3-3. Address ranges for on-chip DARAM in data
memory are:
•
•
•
•
DARAM4: 018000h-019FFFh
DARAM5: 01A000h-01BFFFh
DARAM6: 01C000h-01DFFFh
DARAM7: 01E000h-01FFFFh
Address ranges for on-chip SARAM in program memory are:
•
•
•
•
•
•
•
•
SARAM0: 028000h-029FFFh
SARAM1: 02A000h-02BFFFh
SARAM2: 02C000h-02DFFFh
SARAM3: 02E000h-02FFFFh
SARAM4: 038000h-039FFFh
SARAM5: 03A000h-03BFFFh
SARAM6: 03C000h-03DFFFh
SARAM7: 03E000h-03FFFFh
Hex
7F0000
Hex
010000
Program
Program
Hex
020000
Hex
030000
Hex
040000
Program
Program
Program
On-Chip
DARAM0−3
(OVLY=1)
External
On-Chip
DARAM0−3
(OVLY=1)
External
On-Chip
DARAM0−3
(OVLY=1)
External
On-Chip
DARAM0−3
(OVLY=1)
External
On-Chip
DARAM0−3
(OVLY=1)
External
(OVLY=0)
(OVLY=0)
(OVLY=0)
(OVLY=0)
(OVLY=0)
7F7FFF
7F8000
017FFF
018000
027FFF
028000
037FFF
038000
047FFF
048000
......
On-Chip
DARAM4−7
(MP/MC=0)
External
On-Chip
SARAM0−3
(MP/MC=0)
External
On-Chip
SARAM4−7
(MP/MC=0)
External
External
External
(MP/MC=1)
(MP/MC=1)
(MP/MC=1)
7FFFFF
01FFFF
02FFFF
03FFFF
04FFFF
Page 1
XPC=1
Page 2
XPC=2
Page 127
XPC=7Fh
Page 3
XPC=3
Page 4
XPC=4
Figure 3-3. Extended Program Memory Map
3.5.1 Relocatable Interrupt Vector Table
The reset, interrupt, and trap vectors are addressed in program space. These vectors are soft — meaning
that the processor, when taking the trap, loads the program counter (PC) with the trap address and
executes the code at the vector location. Four words, either two 1-word instructions or one 2-word
instruction, are reserved at each vector location to accommodate a delayed branch instruction which
allows branching to the appropriate interrupt service routine without the overhead.
At device reset, the reset, interrupt, and trap vectors are mapped to address FF80h in program space.
However, these vectors can be remapped to the beginning of any 128-word page in program space after
device reset. This is done by loading the interrupt vector pointer (IPTR) bits in the PMST register with the
appropriate 128-word page boundary address. After loading IPTR, any user interrupt or trap vector is
mapped to the new 128-word page.
NOTE
The hardware reset (RS) vector cannot be remapped because the hardware reset loads
the IPTR with 1s. Therefore, the reset vector is always fetched at location FF80h in
program space.
Functional Overview
21
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
15
8
IPTR
R/W-1FF
7
6
5
4
3
2
1
0
IPTR
MP/MC
OVLY
AVIS
DROM
CLKOFF
SMUL
SST
MP/MC pin
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
LEGEND: R = Read, W = Write, n = value present after reset
Figure 3-4. Process Mode Status Register
Table 3-2. Processor Mode Status (PMST) Register Bit Fields
BIT
NAME
RESET
VALUE
FUNCTION
NO.
Interrupt vector pointer. The 9-bit IPTR field points to the 128-word program page where the interrupt
vectors reside. The interrupt vectors can be remapped to RAM for boot-loaded operations. At reset,
these bits are all set to 1; the reset vector always resides at address FF80h in program memory space.
The RESET instruction does not affect this field.
15-7
IPTR
1FFh
Microprocessor/microcomputer mode. MP/MC enables/disables the on-chip ROM to be addressable in
program memory space.
•
•
MP/MC = 0: The on-chip ROM is enabled and addressable.
MP/MC = 1: The on-chip ROM is not available.
MP/MC
pin
6
5
MP/MC
MP/MC is set to the value corresponding to the logic level on the MP/MC pin when sampled at reset.
This pin is not sampled again until the next reset. The RESET instruction does not affect this bit. This
bit can also be set or cleared by software.
RAM overlay. OVLY enables on-chip dual-access data RAM blocks to be mapped into program space.
The values for the OVLY bit are:
OVLY
0
•
•
OVLY = 0: The on-chip RAM is addressable in data space but not in program space.
OVLY = 1: The on-chip RAM is mapped into program space and data space. Data page 0
(addresses 0h to 7Fh), however, is not mapped into program space.
Address visibility mode. AVIS enables/disables the internal program address to be visible at the
address pins.
•
AVIS = 0: The external address lines do not change with the internal program address. Control
and data lines are not affected and the address bus is driven with the last address on the bus.
4
3
AVIS
0
0
•
AVIS = 1: This mode allows the internal program address to appear at the pins of the device so
that the internal program address can be traced. Also, it allows the interrupt vector to be decoded
in conjunction with IACK when the interrupt vectors reside on on-chip memory.
DROM enables on-chip DARAM4-7 to be mapped into data space. The DROM bit values are:
DROM
•
•
DROM = 0: The on-chip DARAM4-7 is not mapped into data space.
DROM = 1: The on-chip DARAM4-7 is mapped into data space.
CLOCKOUT off. When the CLKOFF bit is 1, the output of CLKOUT is disabled and remains at a high
level.
2
1
0
CLKOFF
SMUL
SST
0
Saturation on multiplication. When SMUL = 1, saturation of a multiplication result occurs before
performing the accumulation in a MAC of MAS instruction. The SMUL bit applies only when OVM = 1
and FRCT = 1.
N/A
N/A
Saturation on store. When SST = 1, saturation of the data from the accumulator is enabled before
storing in memory. The saturation is performed after the shift operation.
22
Functional Overview
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
3.6 On-Chip Peripherals
The device has the following peripherals:
•
•
•
•
•
•
•
•
Software-programmable wait-state generator
Programmable bank-switching
A host-port interface (HPI8/16)
Three multichannel buffered serial ports (McBSPs)
A hardware timer
A clock generator with a multiple phase-locked loop (PLL)
Enhanced external parallel interface (XIO2)
A DMA controller (DMA)
3.6.1 Software-Programmable Wait-State Generator
The software wait-state generator of the device can extend external bus cycles by up to fourteen machine
cycles. Devices that require more than fourteen wait states can be interfaced using the hardware READY
line. When all external accesses are configured for zero wait states, the internal clocks to the wait-state
generator are automatically disabled. Disabling the wait-state generator clocks reduces the power
consumption.
The software wait-state register (SWWSR) controls the operation of the wait-state generator. The 14 LSBs
of the SWWSR specify the number of wait states (0 to 7) to be inserted for external memory accesses to
five separate address ranges. This allows a different number of wait states for each of the five address
ranges. Additionally, the software wait-state multiplier (SWSM) bit of the software wait-state control
register (SWCR) defines a multiplication factor of 1 or 2 for the number of wait states. At reset, the
wait-state generator is initialized to provide seven wait states on all external memory accesses. The
SWWSR bit fields are shown in Figure 3-5 and described in Table 3-3.
15
14
12
11
9
8
XPA
I/O
R/W-111
5
DATA
R/W-111
2
DATA
R/W-0
7
6
3
0
DATA
PROGRAM
R/W-111
PROGRAM
R/W-111
R/W-111
LEGEND: R = Read, W = Write, n = value present after reset
Figure 3-5. Software Wait-State Register (SWWSR) [Memory-Mapped Register (MMR) Address
0028h]
Functional Overview
23
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
Table 3-3. Software Wait-State Register (SWWSR) Bit Fields
BIT
NAME
RESET
VALUE
FUNCTION
NO.
Extended program address control bit. XPA is used in conjunction with the program space fields
(bits 0 through 5) to select the address range for program space wait states.
15
XPA
0
I/O space. The field value (0-7) corresponds to the base number of wait states for I/O space accesses
within addresses 0000-FFFFh. The SWSM bit of the SWCR defines a multiplication factor of 1 or 2 for
the base number of wait states.
14-12
11-9
8-6
I/O
111
Upper data space. The field value (0-7) corresponds to the base number of wait states for external
data space accesses within addresses 8000-FFFFh. The SWSM bit of the SWCR defines a
multiplication factor of 1 or 2 for the base number of wait states.
Data
Data
111
111
Lower data space. The field value (0-7) corresponds to the base number of wait states for external
data space accesses within addresses 0000-7FFFh. The SWSM bit of the SWCR defines a
multiplication factor of 1 or 2 for the base number of wait states.
Upper program space. The field value (0-7) corresponds to the base number of wait states for external
program space accesses within the following addresses:
•
•
XPA = 0: xx8000 - xxFFFFh
XPA = 1: 400000h - 7FFFFFh
5-3
2-0
Program
Program
111
111
The SWSM bit of the SWCR defines a multiplication factor of 1 or 2 for the base number of wait states.
Program space. The field value (0-7) corresponds to the base number of wait states for external
program space accesses within the following addresses:
•
•
XPA = 0: xx0000 - xx7FFFh
XPA = 1: 000000 - 3FFFFFh.
The SWSM bit of the SWCR defines a multiplication factor of 1 or 2 for the base number of wait states.
The software wait-state multiplier bit of the software wait-state control register (SWCR) is used to extend
the base number of wait states selected by the SWWSR. The SWCR bit fields are shown in Figure 3-6
and described in Table 3-4.
15
8
Reserved
R/W-0
7
1
0
Reserved
R/W-0
SWSM
R/W-0
LEGEND: R = Read, W = Write, n = value present after reset
Figure 3-6. Software Wait-State Register (SWWSR) [Memory-Mapped Register (MMR) Address
0028h]
Table 3-4. Software Wait-State Control Register (SWCR) Bit Fields
PIN
NAME
RESET
VALUE
FUNCTION
These bits are reserved and are unaffected by writes.
NO.
15-1
Reserved
0
Software wait-state multiplier. Used to multiply the number of wait states defined in the SWWSR by a
factor of 1 or 2.
0
SWSM
0
•
•
SWSM = 0: wait-state base values are unchanged (multiplied by 1)
SWSM = 1: wait-state base values are multiplied by 2 for a maximum of 14 wait states
24
Functional Overview
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
3.6.2 Programmable Bank-Switching
Programmable bank-switching logic allows the device to switch between external memory banks without
requiring external wait states for memories that need additional time to turn off. The bank-switching logic
automatically inserts one cycle when accesses cross a 32K-word memory-bank boundary inside program
or data space.
Bank-switching is defined by the bank-switching control register (BSCR), which is memory-mapped
ataddress 0029h. The bit fields of the BSCR are shown in Figure 3-7 and are described in Table 3-5.
15
14
13
12
11
8
CONSEC
DIVFCT
R/W-11
IACKOFF
Reserved
R
R/W-1
7
R/W-1
3
2
1
0
Reserved
R
HBH
BH
Reserved
R/W-0
R/W-0
R
LEGEND: R = Read, W = Write, n = value present after reset
Figure 3-7. Bank-Switching Control Register BSCR)[MMR Address 0029h]
Table 3-5. Bank-Switching Control Register (BSCR) Fields
RESET
VALUE
BIT
NAME
FUNCTION
Consecutive bank-switching. Specifies the bank-switching mode.
•
CONSEC = 0: Bank-switching on 32K bank boundaries only. This bit is cleared if fast access is
desired for continuous memory reads (i.e., no starting and trailing cycles between read cycles).
CONSEC
15
1
(1)
•
CONSEC = 1: Consecutive bank switches on external memory reads. Each read cycle consists of
3 cycles: starting cycle, read cycle, and trailing cycle.
CLKOUT output divide factor. The CLKOUT output is driven by an on-chip source having a frequency
equal to 1/(DIVFCT+1) of the DSP clock.
•
•
•
•
DIVFCT = 00: CLKOUT is not divided.
14-13 DIVFCT
11
11
DIVFCT = 01: CLKOUT is divided by 2 from the DSP clock.
DIVFCT = 10: CLKOUT is divided by 3 from the DSP clock.
DIVFCT = 11: CLKOUT is divided by 4 from the DSP clock (default value following reset).
IACK signal output off. Controls the output of the IACK signal. IACKOFF is set to 1 at reset.
12
IACKOFF
Rsvd
•
•
IACKOFF = 0: The IACK signal output off function is disabled.
IACKOFF = 1: The IACK signal output off function is enabled.
11-3
Reserved
HPI bus holder. Controls the HPI bus holder. HBH is cleared to 0 at reset.
•
•
HBH = 0: The bus holder is disabled except when HPI16 = 1.
2
HBH
0
0
HBH = 1: The bus holder is enabled. When not driven, the HPI data bus, HD[7:0] is held in the
previous logic level.
Bus holder. Controls the bus holder. BH is cleared to 0 at reset.
•
•
BH = 0: The bus holder is disabled.
1
0
BH
BH = 1: The bus holder is enabled. When not driven, the data bus, D[15:0] is held in the previous
logic level.
Rsvd
Reserved
(1) For additional information, see Section 3.11 of this document.
Functional Overview
25
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
The device has an internal register that holds the MSB of the last address used for a read or write
operation in program or data space. In the non-consecutive bank switches (CONSEC = 0), if the MSB of
the address used for the current read does not match that contained in this internal register, the MSTRB
(memory strobe) signal is not asserted for one CLKOUT cycle. During this extra cycle, the address bus
switches to the new address. The contents of the internal register are replaced with the MSB for the read
of the current address. If the MSB of the address used for the current read matches the bits in the
register, a normal read cycle occurs.
In non-consecutive bank switches (CONSEC = 0), if repeated reads are performed from the same memory
bank, no extra cycles are inserted. When a read is performed from a different memory bank, memory
conflicts are avoided by inserting an extra cycle. For more information, see Section 3.11 of this document.
The bank-switching mechanism automatically inserts one extra cycle in the following cases:
•
•
•
•
A memory read followed by another memory read from a different memory bank.
A program-memory read followed by a data-memory read.
A data-memory read followed by a program-memory read.
A program-memory read followed by another program-memory read from a different page.
3.6.3 Bus Holders
The device has two bus holder control bits, BH (BSCR[1]) and HBH (BSCR[2]), to control the bus keepers
of the address bus (A[17-0]), data bus (D[15-0]), and the HPI data bus (HD[7-0]). Bus keeper
enabling/disabling is described in Table 3-6.
Table 3-6. Bus Holder Control Bits
HPI16 PIN
BH
0
HBH
D[15-0]
OFF
OFF
ON
A[17-0]
OFF
OFF
OFF
OFF
OFF
ON
HD[7-0]
OFF
ON
0
0
0
0
1
1
1
1
0
1
0
1
0
1
0
1
0
1
OFF
ON
1
ON
0
OFF
OFF
ON
ON
0
ON
1
OFF
ON
ON
1
ON
ON
3.7 Parallel I/O Ports
The device has a total of 64K I/O ports. These ports can be addressed by the PORTR instruction or the
PORTW instruction. The IS signal indicates a read/write operation through an I/O port. The device can
interface easily with external devices through the I/O ports while requiring minimal off-chip ad-
dress-decoding circuits.
26
Functional Overview
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
3.7.1 Enhanced 8-/16-Bit Host-Port Interface (HPI8/16)
The host-port interface, also referred to as the HPI8/16, is an enhanced version of the standard 8-bit HPI
found on earlier TMS320C54x™ DSPs (542, 545, 548, and 549). The HPI can be used to interface to an
8-bit or 16-bit host. When the address and data buses for external I/O is not used (to interface to external
devices in program/data/IO spaces), the HPI can be configured as an HPI16 to interface to a 16-bit host.
This configuration can be accomplished by connecting the HPI16 pin to logic "1”.
When the HPI16 pin is connected to a logic ,,0”, the HPI is configured as an HPI8. The HPI8 is an 8-bit
parallel port for interprocessor communication. The features of the HPI8 include:
Standard features:
•
•
•
Sequential transfers (with autoincrement) or random-access transfers
Host interrupt and C54x™ interrupt capability
Multiple data strobes and control pins for interface flexibility
The HPI8 interface consists of an 8-bit bidirectional data bus and various control signals. Sixteen-bit
transfers are accomplished in two parts with the HBIL input designating high or low byte. The host
communicates with the HPI8 through three dedicated registers — the HPI address register (HPIA), the
HPI data register (HPID), and the HPI control register (HPIC). The HPIA and HPID registers are only
accessible by the host, and the HPIC register is accessible by both the host and the device.
Enhanced features:
•
•
Access to entire on-chip RAM through DMA bus
Capability to continue transferring during emulation stop
The HPI16 is an enhanced 16-bit version of the TMS320C54x™ DSP 8-bit host-port interface (HPI8). The
HPI16 is designed to allow a 16-bit host to access the DSP on-chip memory, with the host acting as the
master of the interface. Some of the features of the HPI16 include:
•
•
•
•
16-bit bidirectional data bus
Multiple data strobes and control signals to allow glueless interfacing to a variety of hosts
Only nonmultiplexed address/data modes are supported
18-bit address bus used in nonmultiplexed mode to allow access to all internal memory (including
internal extended address pages)
•
•
HRDY signal to hold off host accesses due to DMA latency
The HPI16 acts as a slave to a 16-bit host processor and allows access to the on-chip memory of the
DSP.
NOTE
Only the nonmultiplexed mode is supported when the HPI is configured as a HPI16.
The HPI functions as a slave and enables the host processor to access the on-chip memory. A major
enhancement to the HPI over previous versions is that it allows host access to the entire on-chip memory
range of the DSP. The host and the DSP both have access to the on-chip RAM at all times and host
accesses are always synchronized to the DSP clock. If the host and the DSP contend for access to the
same location, the host has priority, and the DSP waits for one cycle. Note that since host accesses are
always synchronized to the device clock, an active input clock (CLKIN) is required for HPI accesses during
IDLE states, and host accesses are not allowed while the device reset pin is asserted.
Functional Overview
27
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
3.7.2 HPI Nonmultiplexed Mode
In nonmultiplexed mode, a host with separate address/data buses can access the HPI16 data register
(HPID) via the HD 16-bit bidirectional data bus, and the address register (HPIA) via the 18-bit HA address
bus. The host initiates the access with the strobe signals (HDS1, HDS2, HCS) and controls the direction of
the access with the HR/W signal. The HPI16 can stall host accesses via the HRDY signal. Note that the
HPIC register is not available in nonmultiplexed mode since there are no HCNTL signals available. All
host accesses initiate a DMA read or write access. Figure 3-8 shows a block diagram of the HPI16 in
nonmultiplexed mode. Figure 3-9 shows the HPI memory map.
HOST
HPI16
PPD[15:0]
DATA[15:0]
HPID[15:0]
HINT
DMA
Address[17:0]
HCNTL0
V
CC
HCNTL1
HBIL
HAS
R/W
HR/W
54xx
CPU
Data Strobes
HDS1, HDS2, HCS
HRDY
READY
Figure 3-8. Host-Port Interface — Nonmulltiplexed Mode
28
Functional Overview
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
Address (Hex)
000 0000
Reserved
000 005F
000 0060
Scratch-Pad
RAM
000 007F
000 0080
DARAM0 −
DARAM3
000 7FFF
000 8000
Reserved
001 7FFF
001 8000
DARAM4 −
DARAM7
001 FFFF
002 0000
Reserved
002 7FFF
002 8000
SARAM0 −
SARAM3
002 FFFF
003 0000
Reserved
003 7FFF
003 8000
SARAM4 −
SARAM7
003 FFFF
004 0000
Reserved
07F FFFF
Figure 3-9. HPI Memory Map
Functional Overview
29
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
3.8 Multichannel Buffered Serial Ports (McBSPs)
The device provides three high-speed, full-duplex, multichannel buffered serial ports that allow direct
interface to other C54x/LC54x devices, codecs, and other devices in a system. The McBSPs are based on
the standard serial-port interface found on other 54x devices. Like their predecessors, the McBSPs
provide:
•
•
•
Full-duplex communication
Double-buffer data registers, which allow a continuous data stream
Independent framing and clocking for receive and transmit
In addition, the McBSPs have the following capabilities:
•
Direct interface to:
–
–
–
–
–
–
T1/E1 framers
MVIP switching compatible and ST-BUS compliant devices
IOM-2 compliant devices
AC97-compliant devices
IIS-compliant devices
Serial peripheral interface
•
•
•
•
•
Multichannel transmit and receive of up to 128 channels
A wide selection of data sizes, including 8, 12, 16, 20, 24, or 32 bits
µ-law and A-law companding
Programmable polarity for both frame synchronization and data clocks
Programmable internal clock and frame generation
The McBSP consists of a data path and control path. The six pins, BDX, BDR, BFSX, BFSR, BCLKX, and
BCLKR, connect the control and data paths to external devices. The implemented pins can be
programmed as general-purpose I/O pins if they are not used for serial communication.
The data is communicated to devices interfacing to the McBSP by way of the data transmit (BDX) pin for
transmit and the data receive (BDR) pin for receive. The CPU or DMA reads the received data from the
data receive register (DRR) and writes the data to be transmitted to the data transmit register (DXR). Data
written to the DXR is shifted out to BDX by way of the transmit shift register (XSR). Similarly, receive data
on the BDR pin is shifted into the receive shift register (RSR) and copied into the receive buffer register
(RBR). RBR is then copied to DRR, which can be read by the CPU or DMA. This allows internal data
movement and external data communications simultaneously.
Control information in the form of clocking and frame synchronization is communicated by way of BCLKX,
BCLKR, BFSX, and BFSR. The device communicates to the McBSP by way of 16-bit-wide control
registers accessible via the internal peripheral bus.
The control block consists of internal clock generation, frame synchronization signal generation, and their
control, and multichannel selection. This control block sends notification of important events to the CPU
and DMA by way of two interrupt signals, XINT and RINT, and two event signals, XEVT and REVT.
The on-chip companding hardware allows compression and expansion of data in either µ-law or A-law
format. When companding is used, transmitted data is encoded according to the specified companding
law and received data is decoded to 2s complement format.
The sample rate generator provides the McBSP with several means of selecting clocking and framing for
both the receiver and transmitter. Both the receiver and transmitter can select clocking and framing
independently.
30
Functional Overview
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
The McBSP allows the multiple channels to be independently selected for the transmitter and receiver.
When multiple channels are selected, each frame represents a time-division multiplexed (TDM) data
stream. In using time-division multiplexed data streams, the CPU may only need to process a few of them.
Thus, to save memory and bus bandwidth, multichannel selection allows independent enabling of
particular channels for transmission and reception. All 128 channels in a bit stream consisting of a
maximum of 128 channels can be enabled.
15
10
9
8
Reserved
R
XMCME
XPBBLK
R/W
R/W
7
6
5
4
2
1
0
XPBBLK
XPABLK
R/W
XCBLK
R
Reserved
XMCM
R/W
R
R/W
LEGEND: R = Read, W = Write, n = value present after reset
Figure 3-10. Multichannel Control Register (MCR1)
15
10
9
8
Reserved
RMCME
RPBBLK
R
R/W
R/W
7
6
5
4
2
1
0
RPBBLK
RPABLK
R/W
RCBLK
R
Reserved
RMCM
R/W
R
R/W
LEGEND: R = Read, W = Write, n = value present after reset
Figure 3-11. Multichannel Control Register (MCR2)
The McBSP has two working modes:
•
•
In the first mode, when (R/X)MCME = 0, it is comparable with the McBSPs used in the 5410 where the
normal 32-channel selection is enabled (default).
In the second mode, when (R/X)MCME = 1, it has 128-channel selection capability. Multichannel
control register Bit 9, (R/X)MCME, is used as the 128-channel selection enable bit. Once (R/X)MCME
= 1, twelve new registers ((R/X)CERC - (R/X)CERH) are used to enable the 128-channel selection.
The clock stop mode (CLKSTP) in the McBSP provides compatibility with the serial port interface protocol.
Clock stop mode works with only single-phase frames and one word per frame. The word sizes supported
by the McBSP are programmable for 8-, 12-, 16-, 20-, 24-, or 32-bit operation. When the McBSP is
configured to operate in SPI mode, both the transmitter and the receiver operate together as a master or
as a slave.
Although the BCLKS pin is not available on the device PGE and GGU packages, the device is capable of
synchronization to external clock sources. BCLKX or BCLKR can be used by the sample rate generator
for external synchronization. The sample rate clock mode extended (SCLKME) bit field is located in the
PCR to accommodate this option.
15
14
13
12
11
10
9
8
Reserved
R/W
XIOEN
RIOEN
FSXM
FSRM
CLKXM
CLKRM
R/W
R/W
R/W
R/W
R/W
R/W
7
6
5
4
3
2
1
0
SCLKME
CLKS STAT
DX STAT
DR STAT
FSXP
FSRP
CLKXP
CLKRP
Functional Overview
31
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
LEGEND: R = Read, W = Write, n = value present after reset
Figure 3-12. Pin Control Register (PCR)
The selection of sample rate input clock is made by the combination of the CLKSM (bit 13 in SRGR2) bit
value and the SCLKME bit value as shown in Table 3-7.
Table 3-7. Sample Rate Input Clock Selection
SCLKME
CLKSM
SAMPLE RATE CLOCK MODE
0
0
1
1
0
1
0
1
Reserved (CLKS pin unavailable)
CPU clock
BCLKR
BCLKX
When the SCLKME bit is cleared to 0, the CLKSM bit is used, as before, to select either the CPU clock or
the CLKS pin (not bonded out on the device package) as the sample rate input clock. Setting the
SCLKME bit to 1 enables the CLKSM bit to select between the BCLKR pin or BCLKX pin for the sample
rate input clock.
When either the BCLKR or CLKX is configured this way, the output buffer for the selected pin is
automatically disabled. For example, with SCLKME = 1 and CLKSM = 0, the BCLKR pin is configured as
the input of the sample rate generator. Both the transmitter and receiver circuits can be synchronized to
the sample rate generator output by setting the CLKXM and CLKRM bits of the pin configuration register
(PCR) to 1. Note that the sample rate generator output will only be driven on the BCLKX pin since the
BCLKR output buffer is automatically disabled.
The McBSP is fully static and operates at arbitrary low clock frequencies. For maximum operating
frequency, see Section 5.5.10.
3.9 Hardware Timer
The device features a 16-bit timing circuit with a 4-bit prescaler. The timer counter is decremented by one
every CLKOUT cycle. Each time the counter decrements to 0, a timer interrupt is generated. The timer
can be stopped, restarted, reset, or disabled by specific status bits.
3.10 Clock Generator
The clock generator provides clocks to the device, and consists of a phase-locked loop (PLL) circuit. The
clock generator requires a reference clock input, which can be provided from an external clock source.
The reference clock input is then divided by two (DIV mode) to generate clocks for the device, or the PLL
circuit can be used (PLL mode) to generate the device clock by multiplying the reference clock frequency
by a scale factor, allowing use of a clock source with a lower frequency than that of the CPU. The PLL is
an adaptive circuit that, once synchronized, locks onto and tracks an input clock signal.
When the PLL is initially started, it enters a transitional mode during which the PLL acquires lock with the
input signal. Once the PLL is locked, it continues to track and maintain synchronization with the input
signal. Then, other internal clock circuitry allows the synthesis of new clock frequencies for use as master
clock for the device.
32
Functional Overview
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
This clock generator allows system designers to select the clock source. The sources that drive the clock
generator are:
•
A crystal resonator circuit. The crystal resonator circuit is connected across the X1 and X2/CLKIN pins
of the device to enable the internal oscillator.
•
An external clock. The external clock source is directly connected to the X2/CLKIN pin, and X1 is left
unconnected.
NOTE
The crystal oscillator function is not supported by all die revisions of the device. See the
TMS320VC5416 Digital Signal Processor Silicon Errata (literature number SPRZ172) to
verify which die revisions support this functionality.
The software-programmable PLL features a high level of flexibility, and includes a clock scaler that
provides various clock multiplier ratios, capability to directly enable and disable the PLL, and a PLL lock
timer that can be used to delay switching to PLL clocking mode of the device until lock is achieved.
Devices that have a built-in software-programmable PLL can be configured in one of two clock modes:
•
•
PLL mode. The input clock (X2/CLKIN) is multiplied by 1 of 31 possible ratios.
DIV (divider) mode. The input clock is divided by 2 or 4. Note that when DIV mode is used, the PLL
can be completely disabled in order to minimize power dissipation.
The software-programmable PLL is controlled using the 16-bit memory-mapped (address 0058h) clock
mode register (CLKMD). The CLKMD register is used to define the clock configuration of the PLL clock
module. Note that upon reset, the CLKMD register is initialized with a predetermined value dependent only
upon the state of the CLKMD1 - CLKMD3 pins. For more programming information, see the TMS320C54x
DSP Reference Set, Volume 1: CPU and Peripherals (literature number SPRU131). The CLKMD pin
configured clock options are shown in Table 3-8.
Table 3-8. Clock Mode Settings at Reset
CLKMD1
CLKMD2
CLKMD3
CLKMD RESET VALUE CLOCK MODE(1)
0
0
0
1
1
1
1
0
0
0
1
0
1
1
0
1
0
1
0
0
0
1
1
1
0000h
9007h
4007h
1007h
F007h
0000h
F000h
—
1/2 (PLL disabled)
PLL x 10
PLL x 5
PLL x 2
PLL x 1
1/2 (PLL disabled)
1/4 (PLL disabled)
Reserved (Bypass mode)
(1) The external CLKMD1-CLKMD3 pins are sampled to determine the desired clock generation mode while RS is low. Following reset, the
clock generation mode can be reconfigured by writing to the internal clock mode register in software.
Functional Overview
33
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
3.11 Enhanced External Parallel Interface (XIO2)
The device external interface has been redesigned to include several improvements, including:
simplification of the bus sequence, more immunity to bus contention when transitioning between read and
write operations, the ability for external memory access to the DMA controller, and optimization of the
power-down modes.
The bus sequence on the device still maintains all of the same interface signals as on previous 54x
devices, but the signal sequence has been simplified. Most external accesses now require 3 cycles
composed of a leading cycle, an active (read or write) cycle, and a trailing cycle. The leading and trailing
cycles provide additional immunity against bus contention when switching between read operations and
write operations. To maintain high-speed read access, a consecutive read mode that performs
single-cycle reads as on previous 54x devices is available.
Figure 3-13 shows the bus sequence for three cases: all I/O reads, memory reads in nonconsecutive
mode, or single memory reads in consecutive mode. The accesses shown in Figure 3-13 always require 3
CLKOUT cycles to complete.
CLKOUT
A[22:0]
D[15:0]
R/W
READ
MSTRB or IOSTRB
PS/DS/IS
Leading
Cycle
Read
Cycle
Trailing
Cycle
Figure 3-13. Nonconsecutive Memory Read and I/O Read Bus Sequence
Figure 3-14 shows the bus sequence for repeated memory reads in consecutive mode. The accesses
shown in Figure 3-14 require (2 + n) CLKOUT cycles to complete, where n is the number of consecutive
reads performed.
34
Functional Overview
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
CLKOUT
A[22:0]
D[15:0]
R/W
READ
READ
READ
MSTRB
PS/DS
Leading
Cycle
Read
Cycle
Read
Cycle
Read
Cycle
Trailing
Cycle
Figure 3-14. Consecutive Memory Read Bus Sequence (n = 3 reads)
Figure 3-15 shows the bus sequence for all memory writes and I/O writes. The accesses shown in
Figure 3-15 always require 3 CLKOUT cycles to complete.
Functional Overview
35
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
CLKOUT
A[22:0]
D[15:0]
WRITE
R/W
MSTRB or IOSTRB
PS/DS/IS
Leading
Cycle
Write
Cycle
Trailing
Cycle
Figure 3-15. Memory Write and I/O Write Bus Sequence
The enhanced interface also provides the ability for DMA transfers to extend to external memory. For
more information on DMA capability, see the DMA sections that follow.
The enhanced interface improves the low-power performance already present on the TMS320C5000™
DSP platform by switching off the internal clocks to the interface when it is not being used. This
power-saving feature is automatic, requires no software setup, and causes no latency in the operation of
the interface.
Additional features integrated in the enhanced interface are the ability to automatically insert
bank-switching cycles when crossing 32K memory boundaries (see Section 3.6.2), the ability to program
up to 14 wait states through software (see Section 3.6.1), and the ability to divide down CLKOUT by a
factor of 1, 2, 3, or 4. Dividing down CLKOUT provides an alternative to wait states when interfacing to
slower external memory or peripheral devices. While inserting wait states extends the bus sequence
during read or write accesses, it does not slow down the bus signal sequences at the beginning and the
end of the access. Dividing down CLKOUT provides a method of slowing the entire bus sequence when
necessary. The CLKOUT divide-down factor is controlled through the DIVFCT field in the bank-switching
control register (BSCR) (see Table 3-5).
36
Functional Overview
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
3.12 DMA Controller
The device direct memory access (DMA) controller transfers data between points in the memory map
without intervention by the CPU. The DMA allows movements of data to and from internal program/data
memory, internal peripherals (such as the McBSPs), or external memory devices to occur in the
background of CPU operation. The DMA has six independent programmable channels, allowing six
different contexts for DMA operation.
3.12.1 Features
The DMA has the following features:
•
•
The DMA operates independently of the CPU.
The DMA has six channels. The DMA can keep track of the contexts of six independent block
transfers.
•
•
•
The DMA has higher priority than the CPU for both internal and external accesses.
Each channel has independently programmable priorities.
Each channel's source and destination address registers can have configurable indexes through
memory on each read and write transfer, respectively. The address may remain constant, be
post-incremented, be post-decremented, or be adjusted by a programmable value.
•
•
•
Each read or write internal transfer may be initialized by selected events.
On completion of a half- or entire-block transfer, each DMA channel may send an interrupt to the CPU.
The DMA can perform double-word internal transfers (a 32-bit transfer of two 16-bit words).
3.12.2 DMA External Access
The DMA supports external accesses to data, I/O, and extended program memory. These overlay pages
are only visible to the DMA controller. A maximum of two DMA channels can be used for external memory
accesses. The DMA external accesses require a minimum of 8 cycles for external writes and a minimum
of 11 cycles for external reads assuming the XIO02 is in consecutive mode (CONSEC = 1), wait state is
set to two, and CLKOUT is not divided (DIVFCT = 00).
The control of the bus is arbitrated between the CPU and the DMA. While the DMA or CPU is in control of
the external bus, the other will be held-off via wait states until the current transfer is complete. The DMA
takes precedence over XIO requests.
•
Only two channels are available for external accesses. (One for external reads and one for external
writes.)
•
•
•
•
•
Single-word (16-bit) transfers are supported for external accesses.
The DMA does not support transfers from the peripherals to external memory.
The DMA does not support transfers from external memory to the peripherals.
The DMA does not support external-to-external accesses.
The DMA does not support synchronized external accesses.
15
14
13
12
11
10
2
8
0
AUTOINIT
DINM
IMOD
CTMOD
SLAXS
SIND
1
7
6
5
4
DMS
DLAXS
DIND
DMD
LEGEND: R = Read, W = Write, n = value present after reset
Figure 3-16. DMA Transfer Mode Control Register (DMMCRn)
Functional Overview
37
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
These new bit fields were created to allow the user to define the space-select for the DMA
(internal/external). The functions of the DLAXS and SLAXS bits are as follows:
•
DLAXS(DMMCRn[5]) Destination
–
–
0 = No external access (default internal)
1 = External access
•
SLAXS(DMMCRn[11]) Source
–
–
0 = No external access (default internal)
1 = External access
Table 3-9 lists the DMD bit values and their corresponding destination space.
Table 3-9. DMD Section of the DMMCRn Register
DMD
00
Destination Space
PS
DS
01
10
I/O
11
Reserved
For the CPU external access, software can configure the memory cells to reside inside or outside the
program address map. When the cells are mapped into program space, the device automatically accesses
them when their addresses are within bounds. When the address generation logic generates an address
outside its bounds, the device automatically generates an external access.
38
Functional Overview
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
3.12.3 DMA Memory Maps
The DMA memory maps, shown in Figure 3-17 and Figure 3-18, allows the DMA transfer to be unaffected
by the status of the MP/MC, DROM, and OVLY bits.
Program
Program
Program
Program
Reserved
Hex
0x0000
Hex
010000
Hex
xx0000
Hex
0000
005F
0060
On-Chip
DARAM0
8K Words
DLAXS = 0
SLAXS = 0
1FFF
2000
On-Chip
DARAM1
8K Words
3FFF
4000
Reserved
Reserved
On-Chip
DARAM2
8K Words
5FFF
6000
On-Chip
DARAM3
8K Words
0x7FFF
0x8000
017FFF
018000
7FFF
8000
Reserved
On-Chip
DARAM 4
8K Words
On-Chip
SARAM 0/4
8K Words
019FFF
01A000
0x9FFF
0xA000
On-Chip
DARAM 5
8K Words
On-Chip
SARAM 1/5
8K Words
01BFFF
01C000
0xBFFF
0xC000
On-Chip
DARAM 6
8K Words
On-Chip
SARAM 2/6
8K Words
Reserved
01DFFF
01E000
0xDFFF
0xE000
On-Chip
DARAM 7
8K Words
On-Chip
SARAM 3/7
8K Words
xxFFFF
01FFFF
FFFF
0xFFFF
Page 1
Page 2 − 3
Page 0
Page 4 − 127
Figure 3-17. On-Chip DMA Memory Map for Program Space (DLAXS = 0 and SLAXS = 0)
Functional Overview
39
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
Data Space (0000 - 005F)
Hex
Data Space
I/O Space
Hex
0000
0000
0000
Reserved
001F
Data Space
(See Breakout)
0020
0021
0022
DRR20
DRR10
DXR20
005F
0060
0023
0024
002F
0030
0031
0032
0033
DXR10
Scratch-Pad
RAM
Reserved
DRR22
DRR12
DXR22
DXR12
007F
0080
On-Chip
DARAM0
8K Words
1FFF
2000
On-Chip
DARAM1
8K Words
0034
0035
0036
0037
Reserved
RCERA2
XCERA2
3FFF
4000
On-Chip
DARAM2
8K Words
0038
0039
Reserved
Reserved
5FFF
6000
003A
003B
RECRA0
XECRA0
On-Chip
DARAM3
8K Words
003C
003F
0040
0041
Reserved
DRR21
DRR11
DXR21
DXR11
7FFF
8000
On-Chip
DARAM4
8K Words
0042
0043
9FFF
A000
On-Chip
DARAM5
8K Words
0044
0049
004A
Reserved
RCERA1
BFFF
C000
On-Chip
DARAM6
8K Words
004B
XCERA1
004C
005F
Reserved
DFFF
E000
On-Chip
DARAM7
8K Words
FFFF
FFFF
Figure 3-18. On-Chip DMA Memory Map for Data and IO Space (DLAXS = 0 and SLAXS = 0)
3.12.4 DMA Priority Level
Each DMA channel can be independently assigned high- or low-priority relative to each other. Multiple
DMA channels that are assigned to the same priority level are handled in a round-robin manner.
3.12.5 DMA Source/Destination Address Modification
The DMA provides flexible address-indexing modes for easy implementation of data management
schemes such as autobuffering and circular buffers. Source and destination addresses can be indexed
separately and can be post-incremented, post-decremented, or post-incremented with a specified index
offset.
40
Functional Overview
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
3.12.6 DMA in Autoinitialization Mode
The DMA can automatically reinitialize itself after completion of a block transfer. Some of the DMA
registers can be preloaded for the next block transfer through the DMA reload registers (DMGSA,
DMGDA, DMGCR, and DMGFR). Autoinitialization allows:
•
Continuous operation: Normally, the CPU would have to reinitialize the DMA immediately after the
completion of the current block transfers, but with the reload registers, it can reinitialize these values
for the next block transfer any time after the current block transfer begins.
•
Repetitive operation:The CPU does not preload the reload register with new values for each block
transfer but only loads them on the first block transfer.
The DMA has been enhanced to expand the DMA reload register sets. Each DMA channel now has its
own DMA reload register set. For example, the DMA reload register set for channel 0 has DMGSA0,
DMGDA0, DMGCR0, and DMGFR0 while DMA channel 1 has DMGSA1, DMGDA1, DMGCR1, and
DMGFR1, etc.
To utilize the additional DMA reload registers, the AUTOIX bit is added to the DMPREC register as shown
in Figure 3-19.
15
14
13
8
0
FREE
AUTOIX
DPRC[5:0]
DE[5:0]
7
6
5
IOSEL
LEGEND: R = Read, W = Write, n = value present after reset
Figure 3-19. DMPREC Register
Table 3-10. DMA Reload Register Selection
AUTOIX
0 (default)
1
DMA RELOAD REGISTER USAGE IN AUTO INIT MODE
All DMA channels use DMGSA0, DMGDA0, DMGCR0 and DMGFR0
Each DMA channel uses its own set of reload registers
3.12.7 DMA Transfer Counting
The DMA channel element count register (DMCTRx) and the frame count register (DMFRCx) contain bit
fields that represent the number of frames and the number of elements per frame to be transferred.
•
Frame count. This 8-bit value defines the total number of frames in the block transfer. The maximum
number of frames per block transfer is 128 (FRAME COUNT= 0FFh). The counter is decremented
upon the last read transfer in a frame transfer. Once the last frame is transferred, the selected 8-bit
counter is reloaded with the DMA global frame reload register (DMGFR) if the AUTOINIT bit is set to 1.
A frame count of 0 (default value) means the block transfer contains a single frame.
•
Element count. This 16-bit value defines the number of elements per frame. This counter is
decremented after the read transfer of each element. The maximum number of elements per frame is
65536 (DMCTRn = 0FFFFh). In autoinitialization mode, once the last frame is transferred, the counter
is reloaded with the DMA global count reload register (DMGCR).
Functional Overview
41
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
3.12.8 DMA Transfer in Doubleword Mode
Doubleword mode allows the DMA to transfer 32-bit words in any index mode. In doubleword mode, two
consecutive 16-bit transfers are initiated and the source and destination addresses are automatically
updated following each transfer. In this mode, each 32-bit word is considered to be one element.
3.12.9 DMA Channel Index Registers
The particular DMA channel index register is selected by way of the SIND and DIND fields in the DMA
transfer mode control register (DMMCRn). Unlike basic address adjustment, in conjunction with the frame
index DMFRI0 and DMFRI1, the DMA allows different adjustment amounts depending on whether or not
the element transfer is the last in the current frame. The normal adjustment value (element index) is
contained in the element index registers DMIDX0 and DMIDX1. The adjustment value (frame index) for
the end of the frame, is determined by the selected DMA frame index register, either DMFRI0 or DMFRI1.
The element index and the frame index affect address adjustment as follows:
•
Element index: For all except the last transfer in the frame, the element index determines the amount
to be added to the DMA channel for the source/destination address register (DMSRCx/DMDSTx) as
selected by the SIND/DIND bits.
•
Frame index: If the transfer is the last in a frame, frame index is used for address adjustment as
selected by the SIND/DIND bits. This occurs in both single-frame and multiframe transfers.
3.12.10 DMA Interrupts
The ability of the DMA to interrupt the CPU based on the status of the data transfer is configurable and is
determined by the IMOD and DINM bits in the DMA transfer mode control register (DMMCRn). The
available modes are shown in Table 3-11.
Table 3-11. DMA Interrupts
MODE
ABU (non-decrement)
ABU (non-decrement)
Multiframe
DINM
IMOD
INTERRUPT
1
1
1
1
0
0
0
1
0
1
X
X
At full buffer only
At half buffer and full buffer
At block transfer complete (DMCTRn = DMSEFCn[7:0] = 0)
At end of frame and end of block (DMCTRn = 0)
No interrupt generated
Multiframe
Either
Either
No interrupt generated
3.12.11 DMA Controller Synchronization Events
The transfers associated with each DMA channel can be synchronized to one of several events. The
DSYN bit field of the DMSEFCn register selects the synchronization event for a channel. The list of
possible events and the DSYN values are shown in Table 3-12.
Table 3-12. DMA Synchronization Events
DSYN VALUE
0000b
DMA SYNCHRONIZATION EVENT
No synchronization used
0001b
McBSP0 receive event
McBSP0 transmit event
McBSP2 receive event
McBSP2 transmit event
0010b
0011b
0100b
42
Functional Overview
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
Table 3-12. DMA Synchronization Events (continued)
DSYN VALUE
0101b
DMA SYNCHRONIZATION EVENT
McBSP1 receive event
0110b
McBSP1 transmit event
0111b
McBSP0 receive event - ABIS mode
McBSP0 transmit event - ABIS mode
McBSP2 receive event - ABIS mode
McBSP2 transmit event - ABIS mode
McBSP1 receive event - ABIS mode
McBSP1 transmit event - ABIS mode
Timer interrupt event
1000b
1001b
1010b
1011b
1100b
1101b
1110b
INT3 goes active
1111b
Reserved
The DMA controller can generate a CPU interrupt for each of the six channels. However, due to a limit on
the number of internal CPU interrupt inputs, channels 0, 1, 2, and 3 are multiplexed with other interrupt
sources. DMA channels 0, 1, 2, and 3 share an interrupt line with the receive and transmit portions of the
McBSP. When the device is reset, the interrupts from these three DMA channels are deselected. The
INTSEL bit field in the DMPREC register can be used to select these interrupts, as shown in Table 3-13.
Table 3-13. DMA Channel Interrupt Selection
INTSEL Value
00b (reset)
01b
IMR/IFR[6]
BRINT2
BRINT2
DMAC0
IMR/IFR[7]
BXINT2
IMR/IFR[10]
BRINT1
IMR/IFR[11]
BXINT1
BXINT2
DMAC2
DMAC3
10b
DMAC1
DMAC2
DMAC3
11b
Reserved
3.13 General-Purpose I/O Pins
In addition to the standard BIO and XF pins, the device has pins that can be configured for
general-purpose I/O. These pins are:
•
18 McBSP pins
–
–
–
–
–
–
BCLKX0/1/2,
BCLKR0/1/2
BDR0/1/2
BFSX0/1/2
BFSR0/1/2
BDX0/1/2
•
8 HPI data pins
HD0-HD7
–
The general-purpose I/O function of these pins is only available when the primary pin function is not
required.
3.13.1 McBSP Pins as General-Purpose I/O
When the receive or transmit portion of a McBSP is in reset, its pins can be configured as
general-purpose inputs or outputs. For more details on this feature, see Section 3.8.
Functional Overview
43
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
3.13.2 HPI Data Pins as General-Purpose I/O
The 8-bit bidirectional data bus of the HPI can be used as general-purpose input/output (GPIO) pins when
the HPI is disabled (HPIENA = 0) or when the HPI is used in HPI16 mode (HPI16 = 1). Two
memory-mapped registers are used to control the GPIO function of the HPI data pins—the gen-
eral-purpose I/O control register (GPIOCR) and the general-purpose I/O status register (GPIOSR). The
GPIOCR is shown in Figure 3-20.
15
8
Reserved
0
7
6
5
4
3
2
1
0
DIR7
DIR6
DIR5
DIR4
DIR3
DIR2
DIR1
DIR0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
LEGEND: R = Read, W = Write, n = value present after reset
Figure 3-20. General-Purpose I/O Control Register (GPIOCR) [MMR Address 003Ch]
The direction bits (DIRx) are used to configure HD0-HD7 as inputs or outputs.
The status of the GPIO pins can be monitored using the bits of the GPIOSR. The GPIOSR is shown in
Figure 3-21.
15
8
Reserved
0
7
6
5
4
3
2
1
0
IO7
IO6
IO5
IO4
IO3
IO2
IO1
IO0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
LEGEND: R = Read, W = Write, n = value present after reset
Figure 3-21. General-Purpose I/O Status Register (GPIOSR) [MMR Address 003Dh]
3.14 Device ID Register
A read-only memory-mapped register has been added to the device to allow user application software to
identify on which device the program is being executed.
15
8
CHIP ID
R
7
4
3
0
CHIP REVISION
R
SUBSYSID
R
LEGEND: R = Read, W = Write, n = value present after reset
Figure 3-22. Device ID Register (CSIDR) [MMR Address 003Eh]
44
Functional Overview
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
Table 3-14. Device ID Register (CSIDR) Bits
BIT
FUNCTION
15-8
7-4
Chip ID (hex code of 16)
Chip revision ID
3-0
Subsystem ID (0000b for single core devices)
3.15 Memory-Mapped Registers
The device has 27 memory-mapped CPU registers, which are mapped in data memory space address 0h
to 1Fh. Each device also has a set of memory-mapped registers associated with peripherals. Table 3-15
gives a list of CPU memory-mapped registers (MMRs) available. Table 3-16 shows additional peripheral
MMRs associated with the device.
Table 3-15. CPU Memory-Mapped Registers
ADDRESS
NAME
DESCRIPTION
DEC
0
HEX
0
IMR
IFR
—
Interrupt mask register
Interrupt flag register
Reserved for testing
Status register 0
1
1
2-5
6
2-5
6
ST0
ST1
AL
7
7
Status register 1
8
8
Accumulator A low word (15-0)
AH
9
9
Accumulator A high word (31-16)
Accumulator A guard bits (39-32)
Accumulator B low word (15-0)
Accumulator B high word (31-16)
Accumulator B guard bits (39-32)
Temporary register
AG
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
A
BL
B
BH
C
BG
D
TREG
TRN
AR0
AR1
AR2
AR3
AR4
AR5
AR6
AR7
SP
E
F
Transition register
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
Auxiliary register 0
Auxiliary register 1
Auxiliary register 2
Auxiliary register 3
Auxiliary register 4
Auxiliary register 5
Auxiliary register 6
Auxiliary register 7
Stack pointer register
BK
Circular buffer size register
Block repeat counter
BRC
RSA
REA
PMST
XPC
—
Block repeat start address
Block repeat end address
Processor mode status (PMST) register
Extended program page register
Reserved
Functional Overview
45
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
Table 3-16. Peripheral Memory-Mapped Registers for Each DSP Subsystem
ADDRESS
NAME
DRR20
DESCRIPTION
DEC
HEX
20
32
33
McBSP 0 Data Receive Register 2
McBSP 0 Data Receive Register 1
McBSP 0 Data Transmit Register 2
McBSP 0 Data Transmit Register 1
Timer Register
DRR10
DXR20
DXR10
TIM
21
34
22
35
23
36
24
PRD
37
25
Timer Period Register
TCR
38
26
Timer Control Register
—
39
27
Reserved
SWWSR
BSCR
—
40
28
Software Wait-State Register
Bank-Switching Control Register
Reserved
41
29
42
2A
SWCR
HPIC
43
2B
Software Wait-State Control Register
HPI Control Register (HMODE = 0 only)
Reserved
44
2C
2D-2F
30
—
45-47
48
DRR22
DRR12
DXR22
DXR12
SPSA2
SPSD2
—
McBSP 2 Data Receive Register 2
McBSP 2 Data Receive Register 1
McBSP 2 Data Transmit Register 2
McBSP 2 Data Transmit Register 1
McBSP 2 Subbank Address Register(1)
McBSP 2 Subbank Data Register(1)
Reserved
McBSP 0 Subbank Address Register(1)
McBSP 0 Subbank Data Register(1)
Reserved
49
31
50
32
51
33
52
34
53
35
54-55
56
36-37
38
SPSA0
SPSD0
—
57
39
58-59
60
3A-3B
3C
3D
3E
GPIOCR
GPIOSR
CSIDR
—
General-Purpose I/O Control Register
General-Purpose I/O Status Register
Device ID Register
61
62
63
3F
Reserved
DRR21
DRR11
DXR21
DXR11
—
64
40
McBSP 1 Data Receive Register 2
McBSP 1 Data Receive Register 1
McBSP 1 Data Transmit Register 2
McBSP 1 Data Transmit Register 1
Reserved
McBSP 1 Subbank Address Register(1)
McBSP 1 Subbank Data Register(1)
Reserved
65
41
66
42
67
43
68-71
72
44-47
48
SPSA1
SPSD1
—
73
49
74-83
84
4A-53
54
DMPREC
DMSA
DMSDI
DMSDN
CLKMD
—
DMA Priority and Enable Control Register
DMA Subbank Address Register(2)
DMA Subbank Data Register with Autoincrement(2)
DMA Subbank Data Register(2)
Clock Mode Register (CLKMD)
Reserved
85
55
86
56
87
57
88
58
89-95
59-5F
(1) See Table 3-17 for a detailed description of the McBSP control registers and their subaddresses.
(2) See Table 3-18 for a detailed description of the DMA subbank addressed registers.
46
Functional Overview
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
3.16 McBSP Control Registers and Subaddresses
The control registers for the multichannel buffered serial port (McBSP) are accessed using the subbank
addressing scheme. This allows a set or subbank of registers to be accessed through a single memory
location. The McBSP subbank address register (SPSA) is used as a pointer to select a particular register
within the subbank. The McBSP data register (SPSDx) is used to access (read or write) the selected
register. Table 3-17 shows the McBSP control registers and their corresponding subaddresses.
Table 3-17. McBSP Control Registers and Subaddresses
McBSP0
McBSP1
McBSP2
SUB- AD-
DRESS
DESCRIPTION
NAME
ADDRESS
39h
NAME
ADDRESS
49h
NAME
ADDRESS
35h
SPCR10
SPCR20
RCR10
SPCR11
SPCR21
RCR11
SPCR12
SPCR22
RCR12
00h
01h
02h
03h
04h
05h
06h
07h
08h
09h
0Ah
0Bh
0Ch
0Dh
0Eh
Serial port control register 1
39h
49h
35h
Serial port control register 2
39h
49h
35h
Receive control register 1
RCR20
39h
RCR21
49h
RCR22
35h
Receive control register 2
XCR10
39h
XCR11
49h
XCR12
35h
Transmit control register 1
XCR20
39h
XCR21
49h
XCR22
35h
Transmit control register 2
SRGR10
SRGR20
MCR10
MCR20
RCERA0
RCERB0
XCERA0
XCERB0
PCR0
39h
SRGR11
SRGR21
MCR11
MCR21
RCERA1
RCERB1
XCERA1
XCERB1
PCR1
49h
SRGR12
SRGR22
MCR12
MCR22
RCERA2
RCERA2
XCERA2
XCERA2
PCR2
35h
Sample rate generator register 1
Sample rate generator register 2
Multichannel control register 1
Multichannel control register 2
Receive channel enable register partition A
Receive channel enable register partition B
Transmit channel enable register partition A
Transmit channel enable register partition B
Pin control register
39h
49h
35h
39h
49h
35h
39h
49h
35h
39h
49h
35h
39h
49h
35h
39h
49h
35h
39h
49h
35h
39h
49h
35h
Additional channel enable register for
128-channel selection
RCERC0
RCERD0
XCERC0
XCERD0
RCERE0
RCERF0
XCERE0
XCERF0
RCERG0
RCERH0
XCERG0
XCERH0
39h
39h
39h
39h
39h
39h
39h
39h
39h
39h
39h
39h
RCERC1
RCERD1
XCERC1
XCERD1
RCERE1
RCERF1
XCERE1
XCERF1
RCERG1
RCERH1
XCERG1
XCERH1
49h
49h
49h
49h
49h
49h
49h
49h
49h
49h
49h
49h
RCERC2
RCERD2
XCERC2
XCERD2
RCERE2
RCERF2
XCERE2
XCERF2
RCERG2
RCERH2
XCERG2
XCERH2
35h
35h
35h
35h
35h
35h
35h
35h
35h
35h
35h
35h
010h
011h
012h
013h
014h
015h
016h
017h
018h
019h
01Ah
01Bh
Additional channel enable register for
128-channel selection
Additional channel enable register for
128-channel selection
Additional channel enable register for
128-channel selection
Additional channel enable register for
128-channel selection
Additional channel enable register for
128-channel selection
Additional channel enable register for
128-channel selection
Additional channel enable register for
128-channel selection
Additional channel enable register for
128-channel selection
Additional channel enable register for
128-channel selection
Additional channel enable register for
128-channel selection
Additional channel enable register for
128-channel selection
Functional Overview
47
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
3.17 DMA Subbank Addressed Registers
The direct memory access (DMA) controller has several control registers associated with it. The main
control register (DMPREC) is a standard memory-mapped register. However, the other registers are
accessed using the subbank addressing scheme. This allows a set or subbank of registers to be accessed
through a single memory location. The DMA subbank address (DMSA) register is used as a pointer to
select a particular register within the subbank, while the DMA subbank data (DMSD) register or the DMA
subbank data register with autoincrement (DMSDI) is used to access (read or write) the selected register.
When the DMSDI register is used to access the subbank, the subbank address is automatically
postincremented so that a subsequent access affects the next register within the subbank. This
autoincrement feature is intended for efficient, successive accesses to several control registers. If the
autoincrement feature is not required, the DMSDN register should be used to access the subbank.
Table 3-18 shows the DMA controller subbank addressed registers and their corresponding subaddresses.
Table 3-18. DMA Subbank Addressed Registers
SUB- AD-
NAME
ADDRESS
DESCRIPTION
DMA channel 0 source address register
DRESS
00h
01h
02h
03h
04h
05h
06h
07h
08h
09h
0Ah
0Bh
0Ch
0Dh
0Eh
0Fh
10h
11h
12h
13h
14h
15h
16h
17h
18h
19h
1Ah
1Bh
1Ch
1Dh
1Eh
DMSRC0
DMDST0
DMCTR0
DMSFC0
DMMCR0
DMSRC1
DMDST1
DMCTR1
DMSFC1
DMMCR1
DMSRC2
DMDST2
DMCTR2
DMSFC2
DMMCR2
DMSRC3
DMDST3
DMCTR3
DMSFC3
DMMCR3
DMSRC4
DMDST4
DMCTR4
DMSFC4
DMMCR4
DMSRC5
DMDST5
DMCTR5
DMSFC5
DMMCR5
DMSRCP
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
DMA channel 0 destination address register
DMA channel 0 element count register
DMA channel 0 sync select and frame count register
DMA channel 0 transfer mode control register
DMA channel 1 source address register
DMA channel 1 destination address register
DMA channel 1 element count register
DMA channel 1 sync select and frame count register
DMA channel 1 transfer mode control register
DMA channel 2 source address register
DMA channel 2 destination address register
DMA channel 2 element count register
DMA channel 2 sync select and frame count register
DMA channel 2 transfer mode control register
DMA channel 3 source address register
DMA channel 3 destination address register
DMA channel 3 element count register
DMA channel 3 sync select and frame count register
DMA channel 3 transfer mode control register
DMA channel 4 source address register
DMA channel 4 destination address register
DMA channel 4 element count register
DMA channel 4 sync select and frame count register
DMA channel 4 transfer mode control register
DMA channel 5 source address register
DMA channel 5 destination address register
DMA channel 5 element count register
DMA channel 5 sync select and frame count register
DMA channel 5 transfer mode control register
DMA source program page address (common channel)
48
Functional Overview
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
Table 3-18. DMA Subbank Addressed Registers (continued)
SUB- AD-
DRESS
NAME
ADDRESS
DESCRIPTION
DMDSTP
DMIDX0
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
56h/57h
1Fh
20h
21h
22h
23h
24h
25h
26h
27h
28h
29h
2Ah
2Bh
2Ch
2Dh
2Eh
2Fh
30h
31h
32h
33h
34h
35h
36h
37h
38h
39h
3Ah
3Bh
3Ch
3Dh
DMA destination program page address (common channel)
DMA element index address register 0
DMIDX1
DMA element index address register 1
DMFRI0
DMA frame index register 0
DMFRI1
DMA frame index register 1
DMGSA0
DMGDA0
DMGCR0
DMGFR0
XSRCDP
XDSTDP
DMGSA1
DMGDA1
DMGCR1
DMGFR1
DMGSA2
DMGDA2
DMGCR2
DMGFR2
DMGSA3
DMGDA3
DMGCR3
DMGFR3
DMGSA4
DMGDA4
DMGCR4
DMGFR4
DMGSA5
DMGDA5
DMGCR5
DMGFR5
DMA global source address reload register, channel 0
DMA global destination address reload register, channel 0
DMA global count reload register, channel 0
DMA global frame count reload register, channel 0
DMA extended source data page (currently not supported)
DMA extended destination data page (currently not supported)
DMA global source address reload register, channel 1
DMA global destination address reload register, channel 1
DMA global count reload register, channel 1
DMA global frame count reload register, channel 1
DMA global source address reload register, channel 2
DMA global destination address reload register, channel 2
DMA global count reload register, channel 2
DMA global frame count reload register, channel 2
DMA global source address reload register, channel 3
DMA global destination address reload register, channel 3
DMA global count reload register, channel 3
DMA global frame count reload register, channel 3
DMA global source address reload register, channel 4
DMA global destination address reload register, channel 4
DMA global count reload register, channel 4
DMA global frame count reload register, channel 4
DMA global source address reload register, channel 5
DMA global destination address reload register, channel 5
DMA global count reload register, channel 5
DMA global frame count reload register, channel 5
Functional Overview
49
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
3.18 Interrupts
Vector-relative locations and priorities for all internal and external interrupts are shown in Table 3-19.
Table 3-19. Interrupt Locations and Priorities
TRAP/INTR
NUMBER (K)
NAME
LOCATION DECIMAL HEX
PRIORITY
FUNCTION
RS, SINTR
0
1
0
4
00
04
08
0C
10
14
18
1C
20
24
28
2C
30
34
38
3C
40
44
48
4C
50
54
58
5C
60
64
68
6C
70
74
78-7F
1
2
Reset (hardware and software reset)
Nonmaskable interrupt
NMI, SINT16
SINT17
2
8
—
—
—
—
—
—
—
—
—
—
—
—
—
—
3
Software interrupt #17
SINT18
3
12
Software interrupt #18
SINT19
4
16
Software interrupt #19
SINT20
5
20
Software interrupt #20
SINT21
6
24
Software interrupt #21
SINT22
7
28
Software interrupt #22
SINT23
8
32
Software interrupt #23
SINT24
9
36
Software interrupt #24
SINT25
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30-31
40
Software interrupt #25
SINT26
44
Software interrupt #26
SINT27
48
Software interrupt #27
SINT28
52
Software interrupt #28
SINT29
56
Software interrupt #29
SINT30
60
Software interrupt #30
INT0, SINT0
INT1, SINT1
INT2, SINT2
TINT, SINT3
RINT0, SINT4
XINT0, SINT5
RINT2, SINT6
XINT2, SINT7
INT3, SINT8
HINT, SINT9
RINT1, SINT10
XINT1, SINT11
DMAC4,SINT12
DMAC5,SINT13
Reserved
64
External user interrupt #0
External user interrupt #1
External user interrupt #2
Timer interrupt
68
4
72
5
76
6
80
7
McBSP #0 receive interrupt (default)
McBSP #0 transmit interrupt (default)
McBSP #2 receive interrupt (default)
McBSP #2 transmit interrupt (default)
External user interrupt #3
HPI interrupt
84
8
88
9
92
10
11
12
13
14
15
16
—
96
100
104
108
112
116
120-127
McBSP #1 receive interrupt (default)
McBSP #1 transmit interrupt (default)
DMA channel 4 (default)
DMA channel 5 (default)
Reserved
The bit layout of the interrupt flag register (IFR) and the interrupt mask register (IMR) is shown in
Figure 3-23.
15
14
13
12
11
10
9
8
Reserved
DMAC5
DMAC4
XINT1
RINT1
HINT
INT3
7
6
5
4
3
2
1
0
XINT2
RINT2
XINT0
RINT0
TINT
INT2
INT1
INT0
LEGEND: R = Read, W = Write, n = value present after reset
Figure 3-23. IFR and IMR Registers
50
Functional Overview
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
4
Support
4.1 Documentation Support
Extensive documentation supports all TMS320™ DSP family of devices from product announcement
through applications development. The following types of documentation are available to support the
design and use of the C5000™ platform of DSPs:
SPRU307: TMS320C54x DSP Family Functional Overview
Provides a functional overview of the devices included in the TMS320C54xE DSP generation
of digital signal processors. Included are descriptions of the CPU architecture, bus structure,
memory structure, on-chip peripherals, and instruction set.
SPRA164: Calculation of TMS320LC54x Power Dissipation
Describes the power-saving features of the TMS320LC54x and presents techniques for
analyzing systems and device conditions to determine operating current levels and power
dissipaton. From this information, informed decisions can be made regarding power supply
requirements and thermal management considerations.
The five-volume TMS320C54x DSP Reference Set consists of:
SPRU131: TMS320C54x DSP Reference Set, Volume 1: CPU
Describes the TMS320C54x 16-bit fixed-point general-purpose digital signal processors.
Covered are its architecture, internal register structure, data and program addressing, and
the instruction pipeline. Also includes development support information, parts lists, and
design considerations for using the XDS510 emulator.
SPRU172: TMS320C54x DSP Reference Set, Volume 2: Mnemonic Instruction Set
Describes the TMS320C54x digital signal processor mnemonic instructions individually. Also
includes a summary of instruction set classes and cycles.
SPRU179: TMS320C54x DSP Reference Set, Volume 3: Algebraic Instruction Set
Describes the TMS320C54x digital signal processor algebraic instructions individually. Also
includes a summary of instruction set classes and cycles.
SPRU173: TMS320C54x DSP Reference Set, Volume 4: Applications Guide
Describes software and hardware applications for the TMS320C54x digital signal processor.
Also includes development support information, parts lists, and design considerations for
using the XDS510 emulator.
SPRU302: TMS320C54x DSP Reference Set, Volume 5: Enhanced Peripherals
Describes the enhanced peripherals available on the TMS320C54x digital signal processors.
Includes the multichannel buffered serial ports (McBSPs), direct memory access (DMA)
controller, interprocessor communications, and the HPI-8 and HPI-16 host port interfaces.
The reference set describes in detail the TMS320C54x™ DSP products currently available and the
hardware and software applications, including algorithms, for fixed-point TMS320™ DSP family of devices.
A series of DSP textbooks is published by Prentice-Hall and John Wiley & Sons to support digital signal
processing research and education. The TMS320 DSP newsletter, Details on Signal Processing, is
published quarterly and distributed to update TMS320 DSP customers on product information.
Information regarding TI DSP porducts is also available on the web at www.ti.com.
Support
51
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
4.2 Device and Development-Support Tool Nomenclature
To designate the stages in the product development cycle, TI assigns prefixes to the part numbers of all
TMS320 DSP devices and support tools. Each TMS320 DSP commercial family member has one of three
prefixes: TMX, TMP, or TMS (e.g., TMS320C6412GDK600). Texas Instruments recommends two of three
possible prefix designators for its support tools: TMDX and TMDS. These prefixes represent evolutionary
stages of product development from engineering prototypes (TMX/TMDX) through fully qualified
production devices/tools (TMS/TMDS).
Device development evolutionary flow:
TMX
TMP
TMS
Experimental device that is not necessarily representative of the final device's electrical
specifications
Final silicon die that conforms to the device's electrical specifications but has not completed
quality and reliability verification
Fully qualified production device
Support tool development evolutionary flow:
TMDX
Development-support product that has not yet completed Texas Instruments internal
qualification testing.
TMDS
Fully qualified development-support product
TMX and TMP devices and TMDX development-support tools are shipped with appropriate disclaimers
describing their limitations and intended uses.
"Developmental product is intended for internal evaluation purposes."
TMS devices and TMDS development-support tools have been characterized fully, and the quality and
reliability of the device have been demonstrated fully. TI's standard warranty applies.
Predictions show that prototype devices (TMX or TMP) have a greater failure rate than the standard
production devices. Texas Instruments recommends that these devices not be used in any production
system because their expected end-use failure rate still is undefined. Only qualified production devices are
to be used.
52
Support
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
5
Electrical Specifications
This section provides the absolute maximum ratings and the recommended operating conditions for the
TMS320VC5416 DSP.
5.1 Absolute Maximum Ratings
The absolute maximum ratings are measure over operating case temperature range. Stresses beyond those listed under
"absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated under Section Section 5.3.1 is not implied.
Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage values are with
respect to DVSS
.
DVDD
CVDD
VI
Supply voltage I/O range
Supply voltage core range
Input voltage range
– 0.3 V to 4.0 V
– 0.3 V to 2.0 V
– 0.3 V to 4.5 V
– 0.3 V to 4.5 V
– 40°C to 100°C
– 55°C to 150°C
VO
Output voltage range
TC
Operating case temperature range
Storage temperature range
Tstg
5.2 Recommended Operating Conditions
MIN
2.7
NOM
3.3
MAX UNIT
DVDD
CVDD
CVDD
Device supply voltage, I/O
3.6
1.65
1.65
V
V
V
Device supply voltage, core (VC5416-160)
Device supply voltage, core (VC5416-120)
1.55
1.42
1.6
1.5
DVSS
CVSS
Supply voltage, GND
0
V
RS, INTn, NMI, X2/CLKIN,
CLKMDn, BCLKRn, BCLKXn,
HCS, HDS1, HDS2, HAS,
TRST, BIO, Dn, An, HDn, TCK
DVDD = 2.7 V to 3.6 V
2.4
DVDD + 0.3
VIH
High-level input voltage, I/O
V
All other inputs
2
DVDD + 0.3
VIL
IOH
IOL
TC
Low-level input voltage
– 0.3
0.8
– 8
8
V
High-level output current(1)(2)
Low-level output current(1)(2)
Operating case temperature
mA
mA
°C
– 40
100
(1) The maximum output currents are DC values only. Transient currents may exceed these values.
(2) These output current limits are used for the test conditions on VOL and VOH, except where noted otherwise.
Electrical Specifications
53
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
5.3 Electrical Characteristics
The electrical charactheristics are measured over recommended operating case temperature range (unless otherwise noted).
All values are typical unless otherwise specified.
PARAMETER
High-level output voltage(1)
Low-level output voltage(1)
TEST CONDITIONS
DVDD = 2.7 V to 3 V, IOH = -2 mA
DVDD = 3 V to 3.6 V, IOH = MAX
IOL = MAX
MIN
TYP
MAX UNIT
2.2
VOH
VOL
V
2.4
0.4
40
V
X2/CLKIN
– 40
– 10
µA
TRST, HPI16
HPIENA
TMS, TCK, TDI, HPI(2) With internal pullups
With internal pulldown
800
400
10
With internal pulldown, RS = 0
– 10
Input current (VI =
DVSS to DVDD
II
– 400
)
µA
A[17:0], D[15:0],
HD[7:0]
Bus holders enabled, DVDD = MAX(3)
– 275
– 5
275
5
All other input-only pins
IDDC
IDDP
Supply current, core CPU
Supply current, pins
CVDD = 1.6 V, fx = 160 ,(4)TC = 25°C
DVDD = 3.0 V, fx = 160 MHz,(4)TC = 25°C
PLL × 1 mode, 20 MHz input
TC = 25°C
60(5)
40(6)
2
mA
mA
IDLE2
Supply current,
standby
IDD
1
mA
IDLE3 Divide-by-two
mode, CLKIN stopped
TC = 100°C
30
5
Ci
Input capacitance
Output capacitance
pF
pF
Co
5
(1) All input and output voltage levels except RS, INT0-INT3, NMI, X2/CLKIN, CLKMD1-CLKMD3, BCLKRn, BCLKXn, HCS, HAS, HDS1,
HDS2, BIO, TCK, TRST, Dn, An, HDn are LVTTL-compatible.
(2) HPI input signals except for HPIENA and HPI16, when HPIENA = 0.
(3)
VIL(MIN) ≤VI ≤VIL(MAX) or VIH(MIN) ≤ VI ≤ VIH(MAX)
(4) Clock mode: PLL × 1 with external source
(5) This value was obtained with 50% usage of MAC and 50% usage of NOP instructions. Actual operating current varies with program
being executed.
(6) This value was obtained with single-cycle external writes, CLKOFF = 0 and load = 15 pF. For more details on how this calculation is
performed, refer to the Calculation of TMS320LC54x Power Dissipation application report (literature number SPRA164).
5.3.1 Test Loading
Tester Pin Electronics
Data Sheet Timing Reference Point
42 W
3.5 nH
Output
Under
Test
Transmission Line
Z0 = 50 W
(see note)
Device Pin
(see note)
4.0 pF
1.85 pF
NOTE: The data sheet provides timing at the device pin. For output timing analysis, the tester pin electronics and its transmission line effects must
taken into account. A transmission line with a delay of 2 ns or longer can be used to produce the desired transmission line effect. The
transmissionline is intended as a load only. It is not necessary to add or subtract the transmission line delay (2 ns or longer) from the data
sheet timings.
Input requirements in this data sheet are tested with an input slew rate of < 4 Volts per nanosecond (4 V/ns) at the device pin.
Figure 5-1. Tester Pin Electronics
54
Electrical Specifications
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
5.3.2 Timing Parameter Symbology
Timing parameter symbols used in the timing requirements and switching characteristics tables are
created in accordance with JEDEC Standard 100. To shorten the symbols, some of the pin names and
other related terminology have been abbreviated as follows:
Lowercase subscripts and their meanings:
Letters and symbols and their meanings:
a
c
d
access time
H
L
High
cycle time (period)
delay time
Low
V
Z
Valid
dis disable time
en enable time
High impedance
f
fall time
hold time
rise time
h
r
su setup time
t
transition time
v
w
X
valid time
pulse duration (width)
Unknown, changing, or don't care level
Electrical Specifications
55
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
5.3.3 Internal Oscillator With External Crystal
The internal oscillator is enabled by selecting the appropriate clock mode at reset (this is de-
vice-dependent; see Section Section 3.10) and connecting a crystal or ceramic resonator across X1 and
X2/CLKIN. The CPU clock frequency is one-half, one-fourth, or a multiple of the oscillator frequency. The
multiply ratio is determined by the bit settings in the CLKMD register.
The crystal should be in fundamental-mode operation, and parallel resonant, with an effective series
resistance of 30 Ω maximum and power dissipation of 1 mW. The connection of the required circuit,
consisting of the crystal and two load capacitors, is shown in Figure 5-2. The load capacitors, C1 and C2,
should be chosen such that the equation below is satisfied. CL (recommended value of 10 pF) in the
equation is the load specified for the crystal.
C1C2
CL +
(C1 ) C2)
Table 5-1. Input Clock Frequency Characteristics
MIN
MAX
Unit
fx
Input clock frequency
10(1)
20(2)
MHz
(1) This device utilizes a fully static design and therefore can operate with tc(CI) approaching ∞. The device is characterized at frequencies
approaching 0 Hz
(2) It is recommended that the PLL multiply by N clocking option be used for maximum frequency operation.
X1
X2/CLKIN
Crystal
C1
C2
Figure 5-2. Internal Divide-By-Two Clock Option With External Crystal
56
Electrical Specifications
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
5.4 Clock Options
The frequency of the reference clock provided at the CLKIN pin can be divided by a factor of two or four or
multiplied by one of several values to generate the internal machine cycle.
5.4.1 Divide-By-Two and Divide-By-Four Clock Options
The frequency of the reference clock provided at the X2/CLKIN pin can be divided by a factor of two or four to
generate the internal machine cycle. The selection of the clock mode is described in Section Section 3.10.
When an external clock source is used, the frequency injected must conform to specifications listed in Table 5-3.
An external frequency source can be used by applying an input clock to X2/CLKIN with X1 left unconnected.
Table 5-2 shows the configuration options for the CLKMD pins that generate the external divide-by-2 or
divide-by-4 clock option. Table 5-3 and Table 5-4 assume testing over recommended operating conditions and H
= 0.5tc(CO) (see Figure 5-3).
Table 5-2. Clock Mode Pin Settings for the Divide-By-2 and By Divide-By-4 Clock Options
CLKMD1
CLKMD2
CLKMD3
Clock Mode
0
1
1
0
0
1
0
1
1
1/2, PLL disabled
1/4, PLL disabled
1/2, PLL disabled
Table 5-3. Divide-By-2 and Divide-By-4 Clock Options Timing Requirements
5416-120
5416-160
Unit
MIN
MAX
tc(CI)
Cycle time, X2/CLKIN
20
ns
ns
ns
ns
ns
tf(CI)
Fall time, X2/CLKIN
4
4
tr(CI)
Rise time, X2/CLKIN
tw(CIL)
tw(CIH)
Pulse duration, X2/CLKIN low
Pulse duration, X2/CLKIN high
4
4
Table 5-4. Divide-By-2 and Divide-By-4 Clock Options Switching Characteristics
5416-120
TYP
5416-160
TYP
PARAMETER
Cycle time, CLKOUT
Unit
MIN
8.33(1)
4
MAX
MIN
6.25(1)
4
MAX
(2)
(2)
tc(CO)
ns
ns
ns
ns
ns
ns
td(CIH-CO)
tf(CO)
Delay time, X2/CLKIN high to CLKOUT high/low
Fall time, CLKOUT
7
1
11
7
1
11
tr(CO)
Rise time, CLKOUT
1
1
tw(COL)
tw(COH)
Pulse duration, CLKOUT low
Pulse duration, CLKOUT high
H – 2
H – 2
H
H
H + 1 H – 2
H + 1 H – 2
H
H
H + 1
H + 1
(1) It is recommended that the PLL clocking operation be used for maximum frequency operation.
(2) This device utilizes a fully static design and therefore can operate with tc(Cl) approaching ∞. The device is characterized at frequencies
approaching 0 Hz.
Electrical Specifications
57
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
t
t
r(CI)
w(CIH)
t
t
f(CI)
w(CIL)
t
c(CI)
X2/CLKIN
t
w(COH)
t
f(CO)
t
c(CO)
t
r(CO)
t
d(CIH-CO)
t
w(COL)
CLKOUT
(see Note A)
A. The CLKOUT timing in this diagram assumes the CLKOUT divide factor (DIVFCT field in the BSCR) is configured as
00 (CLKOUT not divided). DIVFCT is configured as CLKOUT divided-by-4 mode following reset.
Figure 5-3. External Divide-By-Two Clock Timing
58
Electrical Specifications
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
5.4.2 Multiply-By-N Clock Option (PLL Enabled)
The frequency of the reference clock provided at the X2/CLKIN pin can be multiplied by a factor of N to generate
the internal machine cycle. The selection of the clock mode and the value of N is described in Section
Section 3.10. Following reset, the software PLL can be programmed for the desired multiplication factor. Refer to
the TMS320C54x DSP Reference Set, Volume 1: CPU and Peripherals (literature number SPRU131) for detailed
information on programming the PLL.
When an external clock source is used, the external frequency injected must conform to specifications listed in
Table 5-5.
Table 5-5 and Table 5-6 assume testing over recommended operating conditions and H = 0.5tc(CO) (see
Figure 5-4).
Table 5-5. Multiply-By-N Clock Option Timing Requirements
5416-120
5416-160
Unit
MIN
20
MAX
Integer PLL multiplier N (N = 1-15)(1)
PLL multiplier N = x.5(1)
PLL multiplier N = x.25, x.75(1)
200
100
50
4
tc(CI)
Cycle time, X2/CLKIN
20
ns
20
tf(CI)
Fall time, X2/CLKIN
ns
ns
ns
ns
tr(CI)
Rise time, X2/CLKIN
4
tw(CIL)
tw(CIH)
Pulse duration, X2/CLKIN low
Pulse duration, X2/CLKIN high
4
4
(1) N is the multiplication factor.
Table 5-6. Multiply-By-N Clock Option Switching Characteristics
5416-120
TYP
5416-160
TYP
PARAMETER
Cycle time, CLKOUT
Unit
MIN
8.33
4
MAX
MIN
6.25
4
MAX
tc(CO)
td(CI-CO)
tf(CO)
ns
ns
ns
ns
ns
ns
ms
Delay time, X2/CLKIN high/low to CLKOUT high/low
Fall time, CLKOUT
7
2
11
7
2
11
tr(CO)
tw(COL)
tw(COH)
tp
Rise time, CLKOUT
2
2
Pulse duration, CLKOUT low
Pulse duration, CLKOUT high
Transitory phase, PLL lock-up time
H – 2
H – 2
H
H
H + 1 H – 2
H + 1 H – 2
30
H
H
H + 1
H + 1
30
t
t
f(CI)
w(CIH)
t
r(CI)
t
t
c(CI)
w(CIL)
X2/CLKIN
t
d(CI-CO)
t
t
f(CO)
t
w(COH)
t
c(CO)
w(COL)
t
r(CO)
t
p
CLKOUT
(see Note A)
Unstable
A. The CLKOUT timing in this diagram assumes the CLKOUT divide factor (DIVFCT field in the BSCR) is configured as
00 (CLKOUT not divided). DIVFCT is configured as CLKOUT divided-by-4 mode following reset.
Figure 5-4. Multiply-By-One Clock Timing
Electrical Specifications
59
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
5.5 Memory and Parallel I/O Interface Timing
5.5.1 Memory Read
External memory reads can be performed in consecutive or nonconsecutive mode under control of the CONSEC
bit in the BSCR. Table 5-7 and Table 5-8 assume testing over recommended operating conditions with MSTRB =
0 and H = 0.5tc(CO) (see Figure 5-5 and Figure 5-6).
Table 5-7. Memory Read Timing Requirements
5416-120
5416-160
UNIT
MIN
MAX
ta(A)M1
ta(A)M2
tsu(D)R
th(D)R
Access time, read data access from address valid, first read access(1)
Access time, read data access from address valid, consecutive read accesses(1)
Setup time, read data valid before CLKOUT low
4H–9
2H–9
ns
ns
ns
ns
7
0
Hold time, read data valid after CLKOUT low
(1) Address, R/W, PS, DS, and IS timings are all included in timings referenced as address.
Table 5-8. Memory Read Switching Characteristics
5416-120
5416-160
PARAMETER
UNIT
MIN
–1
–1
0
MAX
td(CLKL-A)
Delay time, CLKOUT low to address valid(1)
Delay time, CLKOUT low to MSTRB low
Delay time, CLKOUT low to MSTRB high
4
4
4
ns
ns
ns
td(CLKL-MSL)
td(CLKL-MSH)
(1) Address, R/W, PS, DS, and IS timings are all included in timings referenced as address.
60
Electrical Specifications
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
CLKOUT
t
d(CLKL-A)
A[22:0]
(see Note A)
t
d(CLKL-MSL)
t
d(CLKL-MSH)
t
a(A)M1
D[15:0]
MSTRB
t
su(D)R
t
h(D)R
R/W
(see Note A)
PS/DS
(see Note A)
A. Address, R/W, PS, DS, and IS timings are all included in timings referenced as address.
Figure 5-5. Nonconsecutive Mode Memory Reads
Electrical Specifications
61
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
CLKOUT
t
d(CLKL-A)
t
t
t
d(CLKL-MSL)
d(CLKL-A)
d(CLKL-A)
A[22:0]
(see Note A)
t
t
d(CLKL-MSH)
a(A)M1
t
a(A)M2
D[15:0]
MSTRB
t
t
su(D)R
su(D)R
t
t
h(D)R
h(D)R
R/W
(see Note A)
PS/DS
(see Note A)
A. Address, R/W, PS, DS, and IS timings are all included in timings referenced as address.
Figure 5-6. Consecutive Mode Memory Reads
62
Electrical Specifications
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
5.5.2 Memory Write
Table 5-9 assumes testing over recommended operating conditions with MSTRB = 0 and H = 0.5tc(CO) (see
Figure 5-7).
Table 5-9. Memory Write Switching Characteristics
5416-120
5416-160
PARAMETER
UNIT
MIN
–1
MAX
td(CLKL-A)
tsu(A)MSL
Delay time, CLKOUT low to address valid(1)
Setup time, address valid before MSTRB low(1)
Delay time, CLKOUT low to data valid
Setup time, data valid before MSTRB high
Hold time, data valid after MSTRB high
Delay time, CLKOUT low to MSTRB low
Pulse duration, MSTRB low
4
ns
ns
ns
ns
ns
ns
ns
ns
2H – 3
–1
td(CLKL-D)W
tsu(D)MSH
th(D)MSH
4
2H – 4 2H + 6
2H – 5 2H + 6
td(CLKL-MSL)
tw(SL)MS
–1
2H – 2
0
4
td(CLKL-MSH)
Delay time, CLKOUT low to MSTRB high
4
(1) Address, R/W, PS, DS, and IS timings are all included in timings referenced as address.
CLKOUT
t
d(CLKL-A)
t
d(CLKL-A)
t
d(CLKL-D)W
t
su(A)MSL
A[22:0]
(see Note A)
t
su(D)MSH
t
h(D)MSH
D[15:0]
t
d(CLKL-MSL)
t
d(CLKL-MSH)
t
w(SL)MS
MSTRB
R/W
(see Note A)
PS/DS
(see Note A)
A. Address, R/W, PS, DS, and IS timings are all included in timings referenced as address.
Figure 5-7. Memory Write (MSTRB = 0)
Electrical Specifications
63
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
5.5.3 I/O Read
Table 5-10 and Table 5-11 assume testing over recommended operating conditions, IOSTRB = 0, and H =
0.5tc(CO) (see Figure 5-8).
Table 5-10. I/O Read Timing Requirements
5416-120
5416-160
UNIT
MIN
MAX
4H – 9
ta(A)M1
tsu(D)R
th(D)R
Access time, read data access from address valid, first read access(1)
Setup time, read data valid before CLKOUT low
ns
ns
ns
7
0
Hold time, read data valid after CLKOUT low
(1) Address, R/W, PS, DS, and IS timings are all included in timings referenced as address.
Table 5-11. I/O Read Switching Characteristics
5416-120
5416-160
PARAMETER
UNIT
MIN
– 1
– 1
0
MAX
td(CLKL-A)
Delay time, CLKOUT low to address valid(1)
Delay time, CLKOUT low to IOSTRB low
Delay time, CLKOUT low to IOSTRB high
4
4
4
ns
ns
ns
td(CLKL-IOSL)
td(CLKL-IOSH)
(1) Address, R/W, PS, DS, and IS timings are all included in timings referenced as address.
64
Electrical Specifications
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
CLKOUT
t
t
d(CLKL-A)
d(CLKL-A)
t
d(CLKL-IOSL)
t
d(CLKL-IOSH)
A[22:0]
(see Note A)
t
a(A)M1
t
su(D)R
t
h(D)R
D[15:0]
IOSTRB
R/W
(see Note A)
IS
(see Note A)
A. Address, R/W, PS, DS, and IS timings are all included in timings referenced as address.
Figure 5-8. Parallel I/O Port Read (IOSTRB = 0)
5.5.4 I/O Write
Table 5-12 assumes testing over recommended operating conditions, IOSTRB = 0, and H = 0.5tc(CO) (see
Figure 5-9).
Table 5-12. I/O Write Switching Characteristics
5416-120
5416-160
PARAMETER
UNIT
MIN
– 1
MAX
td(CLKL-A)
tsu(A)IOSL
Delay time, CLKOUT low to address valid(1)
Setup time, address valid before IOSTRB low(1)
Delay time, CLKOUT low to write data valid
Setup time, data valid before IOSTRB high
Hold time, data valid after IOSTRB high
Delay time, CLKOUT low to IOSTRB low
Pulse duration, IOSTRB low
4
ns
ns
ns
ns
ns
ns
ns
ns
2H – 3
– 1
td(CLKL-D)W
tsu(D)IOSH
th(D)IOSH
4
2H – 4 2H + 6
2H – 5 2H + 6
td(CLKL-IOSL)
tw(SL)IOS
– 1
2H – 2
0
4
td(CLKL-IOSH)
Delay time, CLKOUT low to IOSTRB high
4
(1) Address, R/W, PS, DS, and IS timings are all included in timings referenced as address.
Electrical Specifications
65
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
CLKOUT
t
t
d(CLKL-A)
d(CLKL-A)
A[22:0]
(see Note A)
t
d(CLKL-D)W
t
d(CLKL-D)W
t
su(A)IOSL
D[15:0]
t
su(D)IOSH
t
d(CLKL-IOSH)
t
h(D)IOSH
t
d(CLKL-IOSL)
IOSTRB
t
R/W
w(SL)IOS
(see Note A)
IS
(see Note A)
A. Address, R/W, PS, DS, and IS timings are all included in timings referenced as address.
Figure 5-9. Parallel I/O Port Write (IOSTRB = 0)
66
Electrical Specifications
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
5.5.5 Ready Timing for Externally Generated Wait States
Table 5-13 and Table 5-14 assume testing over recommended operating conditions and H = 0.5tc(CO) (see
Figure 5-10, Figure 5-11, Figure 5-12, and Figure 5-13).
Table 5-13. Ready Timing Requirements for Externally Generated Wait States(1)
5416-120
5416-160
UNIT
MIN
7
MAX
tsu(RDY)
Setup time, READY before CLKOUT low
Hold time, READY after CLKOUT low
Valid time, READY after MSTRB low(2)
Hold time, READY after MSTRB low(2)
Valid time, READY after IOSTRB low(2)
Hold time, READY after IOSTRB low(2)
ns
ns
ns
ns
ns
ns
th(RDY)
0
tv(RDY)MSTRB
th(RDY)MSTRB
tv(RDY)IOSTRB
th(RDY)IOSTRB
4H – 4
4H – 4
4H
4H
(1) The hardware wait states can be used only in conjunction with the software wait states to extend the bus cycles. To generate wait states
by READY, as least two software wait states must be programmed. READY is not sampled until the completion of the internal software
wait states.
(2) These timings are included for reference only. The critical timings for READY are those referenced to CLKOUT.
Table 5-14. Ready Switching Characteristics for Externally Generated Wait States(1)
5416-120
5416-160
PARAMETER
UNIT
MIN
0
MAX
td(MSCL)
td(MSCH)
Delay time, CLKOUT low to MSC low
Delay time, CLKOUT low to MSC high
4
4
ns
ns
0
(1) The hardware wait states can be used only in conjunction with the software wait states to extend the bus cycles. To generate wait states
by READY, as least two software wait states must be programmed. READY is not sampled until the completion of the internal software
wait states.
Electrical Specifications
67
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
CLKOUT
A[22:0]
D[15:0]
READY
t
su(RDY)
t
h(RDY)
t
v(RDY)MSTRB
t
h(RDY)MSTRB
MSTRB
MSC
t
d(MSCL)
t
d(MSCH)
Leading
Cycle
Wait States
Generated In-
ternally
Wait
States
Generated
by READY
Trailing
Cycle
Figure 5-10. Memory Read With Externally Generated Wait States
68
Electrical Specifications
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
CLKOUT
A[22:0]
D[15:0]
t
su(RDY)
t
h(RDY)
READY
MSTRB
MSC
t
v(RDY)MSTRB
t
h(RDY)MSTRB
t
d(MSCL)
t
d(MSCH)
Leading
Cycle
Wait
States
Generated
by READY
Wait
States
Generated
Trailing
Cycle
Internally
Figure 5-11. Memory Write With Externally Generated Wait States
Electrical Specifications
69
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
CLKOUT
A[22:0]
D[15:0]
READY
t
su(RDY)
t
h(RDY)
t
v(RDY)IOSTRB
t
h(RDY)IOSTRB
IOSTRB
MSC
t
d(MSCL)
t
d(MSCH)
Leading
Cycle
Wait States
Generated In-
ternally
Wait
States
Generated
by READY
Trailing
Cycle
Figure 5-12. I/O Read With Externally Generated Wait States
70
Electrical Specifications
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
CLKOUT
A[22:0]
D[15:0]
t
su(RDY)
t
h(RDY)
READY
IOSTRB
MSC
t
v(RDY)IOSTRB
t
h(RDY)IOSTRB
t
d(MSCL)
t
d(MSCH)
Leading
Cycle
Wait
States
Generated
Trailing
Cycle
Wait
States
Generated
Internally
by READY
Figure 5-13. I/O Write With Externally Generated Wait States
Electrical Specifications
71
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
5.5.6 HOLD and HOLDA Timings
Table 5-15 and Table 5-16 assume testing over recommended operating conditions and H = 0.5tc(CO) (see
Figure 5-14).
Table 5-15. HOLD and HOLDA Timing Requirements
5416-120
5416-160
UNIT
MIN
4H+8
7
MAX
tw(HOLD)
tsu(HOLD)
Pulse duration, HOLD low duration
Setup time, HOLD before CLKOUT low(1)
ns
ns
(1) This input can be driven from an asynchronous source, therefore, there are no specific timing requirments with respect to CLKOUT.
However, if this timing is met, the input will be recognized on the CLKOUT edge referenced.
Table 5-16. HOLD and HOLDA Switching Characteristics
5416-120
5416-160
PARAMETER
UNIT
MIN
MAX
tdis(CLKL-A)
tdis(CLKL-RW)
tdis(CLKL-S)
ten(CLKL-A)
ten(CLKL-RW)
ten(CLKL-S)
Disable time, Address, PS, DS, IS high impedance from CLKOUT low
Disable time, R/W high impedance from CLKOUT low
Disable time, MSTRB, IOSTRB high impedance from CLKOUT low
Enable time, Address, PS, DS, IS valid from CLKOUT low
Enable time, R/W enabled from CLKOUT low
3
3
ns
ns
ns
ns
ns
ns
ns
ns
ns
3
2H+3
2H+3
2H+3
4
Enable time, MSTRB, IOSTRB enabled from CLKOUT low
Valid time, HOLDA low after CLKOUT low
2
– 1
tv(HOLDA)
tw(HOLDA)
Valid time, HOLDA high after CLKOUT low
– 1
4
Pulse duration, HOLDA low duration
2H–3
72
Electrical Specifications
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
CLKOUT
t
t
su(HOLD)
su(HOLD)
t
w(HOLD)
HOLD
t
t
v(HOLDA)
v(HOLDA)
t
w(HOLDA)
HOLDA
t
t
en(CLKL−A)
dis(CLKL−A)
A[22:0]
PS, DS, IS
D[15:0]
R/W
t
t
t
t
dis(CLKL−RW)
dis(CLKL−S)
dis(CLKL−S)
en(CLKL−RW)
t
en(CLKL−S)
MSTRB
IOSTRB
t
en(CLKL−S)
Figure 5-14. HOLD and HOLDA Timings (HM = 1)
Electrical Specifications
73
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
5.5.7 Reset, BIO, Interrupt, and MP/MC Timings
Table 5-17 assumes testing over recommended operating conditions and H = 0.5tc(CO) (see Figure 5-15,
Figure 5-16, and Figure 5-17).
Table 5-17. Reset, BIO, Interrupt, and MP/MC Timing Requirements
5416-120
5416-160
UNIT
MIN
MAX
th(RS)
Hold time, RS after CLKOUT low(1)
Hold time, BIO after CLKOUT low(1)
Hold time, INTn, NMI, after CLKOUT low(1)(2)
Hold time, MP/MC after CLKOUT low(1)
Pulse duration, RS low(3)(4)
2
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
th(BIO)
4
th(INT)
0
th(MPMC)
tw(RSL)
4
4H + 3
tw(BIO)S
tw(BIO)A
tw(INTH)S
tw(INTH)A
tw(INTL)S
tw(INTL)A
tw(INTL)WKP
tsu(RS)
Pulse duration, BIO low, synchronous
2H + 3
Pulse duration, BIO low, asynchronous
Pulse duration, INTn, NMI high (synchronous)
Pulse duration, INTn, NMI high (asynchronous)
Pulse duration, INTn, NMI low (synchronous)
Pulse duration, INTn, NMI low (asynchronous)
Pulse duration, INTn, NMI low for IDLE2/IDLE3 wakeup
Setup time, RS before X2/CLKIN low(2)(1)
Setup time, BIO before CLKOUT low(1)
Setup time, INTn, NMI, RS before CLKOUT low(1)
Setup time, MP/MC before CLKOUT low(1)
4H
2H + 2
4H
2H + 2
4H
7
3
tsu(BIO)
7
tsu(INT)
7
tsu(MPMC)
5
(1) These inputs can be driven from an asynchronous source, therefore, there are no specific timing requirements with respect to CLKOUT,
however, if setup and hod timings are met, the input will be recognized on the CLKOUT edge referenced.
(2) The external interrupts (INT0-INT3, NMI) are synchronized to the core CPU by way of a two-flip-flop synchronizer that samples thse
inputs with consecutive falling edges of CLKOUT. The input to the interrupt pins is required to represent a1-0-0 sequence at the timing
that is corresponding to three CLKOUTs sampling sequence.
(3) If the PLL mode is selected, then at power-on sequence, or at wakeup from IDLE3, RS must be held low for at least 50 µs to ensure
synchronization and lock-in of the PLL.
(4) Note that RS may cause a change in clock frequency, therefore changing the value of H.
X2/CLKIN
t
su(RS)
t
w(RSL)
RS, INTn, NMI
CLKOUT
BIO
t
su(INT)
t
h(RS)
t
su(BIO)
t
h(BIO)
t
w(BIO)S
Figure 5-15. Reset and BIO Timings
74
Electrical Specifications
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
CLKOUT
t
t
su(INT)
t
su(INT)
h(INT)
INT, NMI
t
w(INTH)A
t
w(INTL)A
Figure 5-16. Interrupt Timing
CLKOUT
RS
t
h(MPMC)
t
su(MPMC)
MP/MC
Figure 5-17. MP/MC Timing
Electrical Specifications
75
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
5.5.8 Instruction Acquisition (IAQ) and Interrupt Acknowledge (IACK) Timings
Table 5-18 assumes testing over recommended operating conditions and H = 0.5tc(CO) (see Figure 5-18).
Table 5-18. Instruction Acquisition (IAQ) and Interrupt Acknowledge (IACK) Switching Characteristics
5416-120
5416-160
PARAMETER
UNIT
MIN
– 1
MAX
td(CLKL-IAQL)
td(CLKL-IAQH)
td(CLKL-IACKL)
td(CLKL-IACKH)
td(CLKL-A)
Delay time, CLKOUT low to IAQ low
4
4
4
4
4
ns
ns
ns
ns
ns
ns
ns
Delay time, CLKOUT low to IAQ high
Delay time, CLKOUT low to IACK low
Delay time, CLKOUT low to IACK high
Delay time, CLKOUT low to address valid
Pulse duration, IAQ low
– 1
– 1
– 1
– 1
tw(IAQL)
2H – 2
2H – 2
tw(IACKL)
Pulse duration, IACK low
CLKOUT
t
d(CLKL−A)
t
d(CLKL−A)
A[22:0]
t
t
t
d(CLKL−IAQH)
d(CLKL−IAQL)
t
w(IAQL)
IAQ
t
d(CLKL−IACKH)
d(CLKL−IACKL)
t
w(IACKL)
IACK
Figure 5-18. Instruction Acquisition (IAQ) and Interrupt Acknowledge (IACK) Timings
76
Electrical Specifications
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
5.5.9 External Flag (XF) and TOUT Timings
Table 5-19 assumes testing over recommended operating conditions and H = 0.5tc(CO) (see Figure 5-19
and Figure 5-20).
Table 5-19. External Flag (XF) and TOUT Switching Characteristics
5416-120
5416-160
PARAMETER
Delay time, CLKOUT low to XF high
UNIT
MIN
MAX
– 1
4
4
4
4
td(XF)
ns
Delay time, CLKOUT low to XF low
Delay time, CLKOUT low to TOUT high
Delay time, CLKOUT low to TOUT low
Pulse duration, TOUT
– 1
td(TOUTH)
td(TOUTL)
tw(TOUT)
– 1
ns
ns
ns
– 1
2H – 4
CLKOUT
t
d(XF)
XF
Figure 5-19. External Flag (XF) Timing
CLKOUT
TOUT
t
t
d(TOUTL)
d(TOUTH)
t
w(TOUT)
Figure 5-20. TOUT Timing
Electrical Specifications
77
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
5.5.10 Multichannel Buffered Serial Port (McBSP) Timing
5.5.10.1 McBSP Transmit and Receive Timings
Table 5-20 and Table 5-21 assume testing over recommended operating conditions (see Figure 5-21 and
Figure 5-22).
Table 5-20. McBSP Transmit and Receive Timing Requirements(1)
5416-120
5416-160
UNIT
MIN MAX
tc(BCKRX)
tw(BCKRX)
Cycle time, BCLKR/X(2)
Pulse duration, BCLKR/X high or BCLKR/X low(2)
BCLKR/X ext
BCLKR/X ext
BCLKR int
BCLKR ext
BCLKR int
BCLKR ext
BCLKR int
BCLKR ext
BCLKR int
BCLKR ext
BCLKX int
BCLKX ext
BCLKX int
BCLKX ext
BCLKR/X ext
BCLKR/X ext
4P(3)
2P–1(3)
ns
ns
8
1
1
2
7
1
2
3
8
1
0
2
tsu(BFRH-BCKRL)
th(BCKRL-BFRH)
tsu(BDRV-BCKRL)
th(BCKRL-BDRV)
tsu(BFXH-BCKXL)
th(BCKXL-BFXH)
Setup time, external BFSR high before BCLKR low
Hold time, external BFSR high after BCLKR low
Setup time, BDR valid before BCLKR low
ns
ns
ns
ns
ns
ns
Hold time, BDR valid after BCLKR low
Setup time, external BFSX high before BCLKX low
Hold time, external BFSX high after BCLKX low
tr(BCKRX)
tf(BCKRX)
Rise time, BCKR/X
Fall time, BCKR/X
6
6
ns
ns
(1) CLKRP = CLKXP = FSRP = FSXP = 0. If the polaritiy of any of the signals is inverted, then the timing references of that signal are also
inverted.
(2) Note that in some cases, for example when driving another 54x device McBSP, maximum serial port clocking rates may not be
achievable at maximum CPU clock frequency due to transmitted data timings and corresponding receive timing requirements. A
separate detailed timing analysis should be performend for each specific McBSP interface.
(3) P = 0.5 * processor clock.
78
Electrical Specifications
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
Table 5-21. McBSP Transmit and Receive Switching Characteristics(1)
5416-120
5416-160
PARAMETER
UNIT
MIN
MAX
tc(BCKRX)
tw(BCKRXH)
tw(BCKRXL)
Cycle time, BCLKR/X(2)
Pulse duration, BCLKR/X high(2)
Pulse duration, BCLKR/X low(2)
BCLKR/X int
BCLKR/X int
BCLKR/X int
BCLKR int
BCLKR ext
BCLKX int
BCLKX ext
BCLKX int
BCLKX ext
BCLKX int
BCLKX ext
BCLKX int
BCLKX ext
BFSX int
4P(3)
D – 1(4) D + 1(4)
C – 1(4) C + 1(4)
ns
ns
ns
ns
ns
– 3
0
3
6
td(BCKRH-BFRV)
td(BCKXH-BFXV)
tdis(BCKXH-BDXHZ)
Delay time, BCLKR high to internal BFSR valid
Delay time, BCLKX high to internal BFSX valid
– 1
3
5
ns
ns
11
6
Disable time, BCLKX high to BDX high impedance following last data
bit of transfer
10
10
20
20
30
7
– 1(5)
3
– 1(5)
DXENA = 0
Delay time, BCLKX high to BDX valid
DXENA = 1
td(BCKXH-BDXV)
ns
ns
3
–1(5)
3
Delay time, BFSX high to BDX valid
ONLY applies when in data delay 0 (XDATDLY = 00b) mode
td(BFXH-BDXV)
BFSX ext
11
(1) CLKRP = CLKXP = FSRP = FSXP = 0. If the polaritiy of any of the signals is inverted, then the timing references of that signal are also
inverted.
(2) Note that in some cases, for example when driving another 54x device McBSP, maximum serial port clocking rates may not be
achievable at maximum CPU clock frequency due to transmitted data timings and corresponding receive timing requirements. A
separate detailed timing analysis should be performend for each specific McBSP interface.
(3) P = 0.5 * processor clock.
(4) T = BCLKRX period = (1 + CLKGDV) * 2P
C = BCLKRX low pulse width = T/2 when CLKGDV is odd or zero and = (CLKGDV/2) * 2P when CLKGDV is even
D = BCLKRX high pulse width = T/2 when CLKGDV is odd or zero and = (CLKGDV/2 +1) * 2P when CLKGDV is even
(5) Minimum delay times also represent minimum output hold times.
t
c(BCKRX)
t
w(BCKRXH)
w(BCKRXL)
t
t
r(BCKRX)
f(BCKRX)
t
BCLKR
BFSR (int)
BFSR (ext)
BDR
t
d(BCKRH-BFRV)
t
d(BCKRH-BFRV)
t
su(BFRH-BCKRL)
t
h(BCKRL-BFRH)
t
su(BDRV-BCKRL)
t
h(BCKRL-BDRV)
(n-2)
(n-3)
Bit(n-1)
Figure 5-21. McBSP Receive Timings
Electrical Specifications
79
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
t
c(BCKRX)
t
t
w(BCKRXH)
w(BCKRXL)
t
t
f(BCKRX)
r(BCKRX)
BCLKX
t
d(BCKXH-BFXV)
BFSX (int)
t
h(BCKXL-BFXH)
t
su(BFXH-BCKXL)
BFSX (ext)
BFSX
(XDATDLY=00b)
t
d(BCKXH-BDXV)
(n-2)
t
d(BFXH-BDXV)
t
t
dis(BCKXH-BDXHZ)
Bit 0
d(BCKXH-BDXV)
BDX
Bit(n-1)
(n-3)
Figure 5-22. McBSP Transmit Timings
80
Electrical Specifications
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
5.5.10.2 McBSP General-Purpose I/O Timing
Table 5-22 and Table 5-23 assume testing over recommended operating conditions (see Figure 5-23).
Table 5-22. McBSP General-Purpose I/O Timing Requirements
5416-120
5416-160
UNIT
MIN
7
MAX
tsu(BGPIO-COH)
th(COH-BGPIO)
Setup time, BGPIOx input mode before CLKOUT high(1)
Hold time, BGPIOx input mode after CLKOUT high(1)
ns
ns
0
(1) BGPIOx refers to BCLKRx, BFSRx, BDRx, BCLKXx, or BFSXx when configured as a general-purpose input.
Table 5-23. McBSP General-Purpose I/O Switching Characteristics
5416-120
5416-160
PARAMETER
UNIT
MIN
MAX
td(COH-BGPIO)
Delay time, CLKOUT high to BGPIOx output mode(1)
– 2
4
ns
(1) BGPIOx refers to BCLKRx, BFSRx, BDRx, BCLKXx, or BFSXx when configured as a general-purpose output.
t
t
su(BGPIO-COH)
d(COH-BGPIO)
CLKOUT
t
h(COH-BGPIO)
BGPIOx Input Mode
(see Note A)
BGPIOx Output Mode
(see Note B)
A. BGPIOx refers to BCLKRx, BFSRx, BDRx, BCLKXx, or BFSXx when configured as a general-purpose input.
B. BGPIOx refers to BCLKRx, BFSRx, BCLKXx, BFSXx, or BDXx when configured as a general-purpose output.
Figure 5-23. McBSP General-Purpose I/O Timings
Electrical Specifications
81
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
5.5.10.3 McBSP as SPI Master or Slave Timing
Table 5-24 to Table 5-31 assume testing over recommended operating conditions (see Figure 5-24,
Figure 5-25, Figure 5-26, and Figure 5-27).
Table 5-24. McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 10b, CLKXP = 0)(1)
5416-120
5416-160
UNIT
MASTER
SLAVE
MIN
12
4
MAX
MIN MAX
tsu(BDRV-BCKXL)
th(BCKXL-BDRV)
Setup time, BDR valid before BCLKX low
Hold time, BDR valid after BCLKX low
2 – 6P(2)
5 + 12P(2)
ns
ns
(1) For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
(2) P = 0.5 * processor clock.
Table 5-25. McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 10b, CLKXP = 0)(1)
5416-120
5416-160
PARAMETER
UNIT
MASTER(2)
SLAVE
MIN
MIN
MAX
MAX
th(BCKXL-BFXL)
td(BFXL-BCKXH)
td(BCKXH-BDXV)
Hold time, BFSX low after BCLKX low(3)
Delay time, BFSX low to BCLKX high(4)
Delay time, BCLKX high to BDX valid
T – 3 T + 4
C – 4 C + 3
ns
ns
ns
– 4
5
6P + 2(5) 10P + 17(5)
Disable time, BDX high impedance following last data bit from
BCLKX low
tdis(BCKXL-BDXHZ)
C – 2 C + 3
ns
Disable time, BDX high impedance following last data bit from
BFSX high
tdis(BFXH-BDXHZ)
td(BFXL-BDXV)
2P– 4(5)
4P+ 2(5)
6P + 17(5)
8P + 17(5)
ns
ns
Delay time, BFSX low to BDX valid
(1) For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
(2) T = BCLKX period = (1 + CLKGDV) * 2P
C = BCLKX low pulse width = T/2 when CLKGDV is odd or zero and = (CLKGDV/2) *2P when CLKGDV is even
(3) FSRP = FSXP = 1. As a SPI master, BFSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input
on BFSX and BFSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FRSRM = 2 for master McBSP
CLKXM = CLKRm = FSXM = FSRM = 0 for slave McBSP
(4) BFSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the
master clock (BCLKX).
(5) P = 0.5 * processor clock.
MSB
LSB
BCLKX
BFSX
t
h(BCKXL-BFXL)
t
d(BFXL-BCKXH)
t
dis(BFXH-BDXHZ)
t
d(BFXL-BDXV)
t
t
d(BCKXH-BDXV)
(n-2)
dis(BCKXL-BDXHZ)
BDX
BDR
Bit 0
Bit(n-1)
(n-3)
(n-4)
t
su(BDRV-BCLXL)
t
h(BCKXL-BDRV)
(n-2)
Bit 0
Bit(n-1)
(n-3)
(n-4)
Figure 5-24. McBSP Timing as SPI Master or Slave: CLKSTP = 10b, CLKXP = 0
82
Electrical Specifications
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
Table 5-26. McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 11b, CLKXP = 0)(1)
5416-120
5416-160
UNIT
MASTER
SLAVE
MIN MAX
MIN MAX
tsu(BDRV-BCKXL)
th(BCKXH-BDRV)
Setup time, BDR valid before BCLKX low
Hold time, BDR valid after BCLKX high
12
4
2 – 6P(2)
5 + 12P(2)
ns
ns
(1) For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
(2) P = 0.5 * processor clock.
Table 5-27. McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 11b, CLKXP = 0)(1)
5416-120
5416-160
PARAMETER
UNIT
MASTER(2)
MIN MAX
SLAVE
MIN
MAX
th(BCKXL-BFXL)
td(BFXL-BCKXH)
td(BCKXL-BDXV)
Hold time, BFSX low after BCLKX low(3)
Delay time, BFSX low to BCLKX high(4)
Delay time, BCLKX low to BDX valid
C –3 C + 4
T – 4 T + 3
ns
ns
ns
– 4
5
6P + 2(5) 10P + 17(5)
6P – 4(5) 10P + 17(5)
Disable time, BDX high impedance following last data bit from
BCLKX low
tdis(BCKXL-BDXHZ)
td(BFXL-BDXV)
– 2
4
ns
ns
D –
2
Delay time, BFSX low to BDX valid
D + 4 4P + 2(5)
8P + 17(5)
(1) For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
(2) T = BCLKX period = (1 + CLKGDV) * 2P
C = BCLKX low pulse width = T/2 when CLKGDV is odd or zero and = (CLKGDV/2) *2P when CLKGDV is even
D = BCLKX high pulse width = T/2 when CLKGDV is odd or zero and (CLKGDV/2 + 1) * 2P when CLKGDV is even
(3) FSRP = FSXP = 1. As a SPI master, BFSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input
on BFSX and BFSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FRSRM = 2 for master McBSP
CLKXM = CLKRm = FSXM = FSRM = 0 for slave McBSP
(4) BFSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the
master clock (BCLKX).
(5) P = 0.5 * processor clock.
MSB
LSB
BCLKX
t
t
d(BFXL-BCKXH)
h(BCKXL-BFXL)
BFSX
t
t
t
d(BCKXL-BDXV)
d(BFXL-BDXV)
dis(BCKXL-BDXHZ)
BDX
Bit 0
Bit(n-1)
Bit(n-1)
(n-2)
(n-3)
(n-4)
t
su(BDRV-BCKXL)
t
h(BCKXH-BDRV)
(n-2)
BDR
Bit 0
(n-3)
(n-4)
Figure 5-25. McBSP Timing as SPI Master or Slave: CLKSTP = 11b, CLKXP = 0
Electrical Specifications
83
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
Table 5-28. McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 10b, CLKXP = 1)(1)
5416-120
5416-160
UNIT
MASTER
SLAVE
MIN
MIN MAX
MAX
tsu(BDRV-BCKXH)
th(BCKXH-BDRV)
Setup time, BDR valid before BCLKX high
Hold time, BDR valid after BCLKX high
12
4
2 – 6P(2)
5 + 12P(2)
ns
ns
(1) For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
(2) P = 0.5 * processor clock.
Table 5-29. McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 10b, CLKXP = 1)(1)
5416-120
5416-160
PARAMETER
UNIT
MASTER(2)
SLAVE
MIN
MIN
MAX
T + 4
MAX
th(BCKXH-BFXL)
td(BFXL-BCKXL)
td(BCKXL-BDXV)
Hold time, BFSX low after BCLKX high(3)
Delay time, BFSX low to BCLKX lowTNote9543(4)
Delay time, BCLKX low to BDX valid
T – 3
ns
ns
ns
D – 4 D + 3
– 4
5
6P + 2(5) 10P + 17(5)
Disable time, BDX high impedance following last data bit from
BCLKX high
tdis(BCKXH-BDXHZ)
D – 2 D + 3
ns
Disable time, BDX high impedance following last data bit from
BFSX high
tdis(BFXH-BDXHZ)
td(BFXL-BDXV)
2P – 4(5)
4P + 2(5)
6P + 17(5)
8P + 17(5)
ns
ns
Delay time, BFSX low to BDX valid
(1) For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
(2) T = BCLKX period = (1 + CLKGDV) * 2P
D = BCLKX high pulse width = T/2 when CLKGDV is odd or zero and (CLKGDV/2 + 1) * 2P when CLKGDV is even
(3) FSRP = FSXP = 1. As a SPI master, BFSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input
on BFSX and BFSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FRSRM = 2 for master McBSP
CLKXM = CLKRm = FSXM = FSRM = 0 for slave McBSP
(4) BFSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the
master clock (BCLKX).
(5) P = 0.5 * processor clock.
LSB
MSB
BCLKX
BFSX
t
h(BCKXH-BFXL)
t
d(BFXL-BCKXL)
t
t
d(BFXL-BDXV)
dis(BFXH-BDXHZ)
t
t
t
d(BCKXL-BDXV)
(n-2)
dis(BCKXH-BDXHZ)
BDX
BDR
Bit 0
Bit(n-1)
(n-3)
(n-4)
t
su(BDRV-BCKXH)
h(BCKXH-BDRV)
(n-2)
Bit 0
Bit(n-1)
(n-3)
(n-4)
Figure 5-26. McBSP Timing as SPI Master or Slave: CLKSTP = 10b, CLKXP = 1
84
Electrical Specifications
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
(1)
Table 5-30. McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 11b, CLKXP = 1)
5416-120
5416-160
UNIT
MASTER
SLAVE
MIN
MIN MAX
MAX
tsu(BDRV-BCKXL)
th(BCKXL–BDRV)
Setup time, BDR valid before BCLKX low
Hold time, BDR valid after BCLKX low
12
4
2 – 6P(2)
5 + 12P(2)
ns
ns
(1) For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
(2) P = 0.5 * processor clock.
(1)
Table 5-31. McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 11b, CLKXP = 1)
5416-120
5416-160
PARAMETER
UNIT
MASTER(2)
SLAVE
MIN
MIN
MAX
MAX
th(BCKXH-BFXL)
td(BFXL-BCKXL)
td(BCKXH-BDXV)
Hold time, BFSX low after BCLKX high(3)
Delay time, BFSX low to BCLKX low(4)
Delay time, BCLKX high to BDX valid
D – 3 D + 4
T – 4 T + 3
ns
ns
ns
– 4
5
6P + 2(5)
6P – 4(5)
4P + 2(5)
10P + 17(5)
10P + 17(5)
8P + 17(5)
Disable time, BDX high impedance following last data bit from
BCLKX high
tdis(BCKXH-BDXHZ)
td(BFXL-BDXV)
– 2
4
ns
ns
Delay time, BFSX low to BDX valid
C – 2 C + 4
(1) For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
(2) T = BCLKX period = (1 + CLKGDV) * 2P
C = BCLKX low pulse width = T/2 when CLKGDV is odd or zero and = (CLKGDV/2) * 2P when CLKGDV is even
D = BCLKX high pulse width = T/2 when CLKGDV is odd or zero and (CLKGDV/2 + 1) * 2P when CLKGDV is even
(3) FSRP = FSXP = 1. As a SPI master, BFSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input
on BFSX and BFSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FRSRM = 2 for master McBSP
CLKXM = CLKRm = FSXM = FSRM = 0 for slave McBSP
(4) BFSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the
master clock (BCLKX).
(5) P = 0.5 * processor clock.
MSB
LSB
BCLKX
t
t
h(BCKXH-BFXL)
d(BFXL-BCKXL)
BFSX
t
t
t
t
dis(BCKXH-BDXHZ)
d(BCKXH-BDXV)
(n-2)
d(BFXL-BDXV)
BDX
Bit 0
Bit(n-1)
Bit(n-1)
(n-3)
(n-4)
su(BDRV-BCKXL)
t
h(BCKXL-BDRV)
(n-2)
BDR
Bit 0
(n-3)
(n-4)
Figure 5-27. McBSP Timing as SPI Master or Slave: CLKSTP = 11b, CLKXP = 1
Electrical Specifications
85
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
5.5.11 Host-Port Interface Timing
5.5.11.1 HPI8 Mode
Table 5-32 and Table 5-33 assume testing over recommended operating conditions and P = 0.5 *
processor clock (see Figure 5-28 through Figure 5-31). In the following tables, DS refers to the logical OR
of HCS, HDS1, and HDS2. HD refers to any of the HPI data bus pins (HD0, HD1, HD2, etc.). HAD stands
for HCNTL0, HCNTL1, and HR/W.
Table 5-32. HPI8 Mode Timing Requirements
5416-120
5416-160
UNIT
MIN
MAX
Setup time, HBIL and HAD valid before DS low (when HAS is not used), or HBIL and HAD
valid before HAS low
tsu(DSL-HBV)
th(DSL-HBV)
6
ns
ns
Hold time, HBIL and HAD valid after DS low (when HAS is not used), or HBIL and HAD
valid after HAS low
3
tsu(HSL-DSL)
tw(DSL)
Setup time, HAS low before DS low
Pulse duration, DS low
8
13
7
ns
ns
ns
ns
ns
tw(DSH)
Pulse duration, DS high
tsu(HDV-DSH)
th(DSH-HDV)W
Setup time, HD valid before DS high, HPI write
Hold time, HD valid after DS high, HPI write
3
2
Setup time, HDx input valid before CLKOUT high, HDx configured as general-purpose
input
tsu(GPIO-COH)
th(GPIO-COH)
3
0
ns
ns
Hold time, HDx input valid before CLKOUT high, HDx configured as general-purpose input
86
Electrical Specifications
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
Table 5-33. HPI8 Mode Switching Characteristics
5416-120
5416-160
PARAMETER
Enable time, HD driven from DS low
UNIT
MIN
MAX
ten(DSL-HD)
0
10
ns
Case 1a: Memory accesses when DMAC is active
36P + 10 –
tw(DSH)
in 32-bit mode and tw(DSH) < 36P(1)
Case 1b: Memory accesses when DMAC is active
10
in 32-bit mode and tw(DSH)≥ 36P(1)
Case 1c: Memory accesses when DMAC is active
in 16-bit mode and tw(DSH) < I8P(1)
18P + 10 –
tw(DSH)
Delay time, DS low to HD valid
for first byte of an HPI read
td(DSL-HDV1)
Case 1d: Memory accesses when DMAC is active
ns
10
in 16-bit mode and tw(DSH)≥ I8P(1)
Case 2a: Memory accesses when DMAC is inactive
and tw(DSH) < 10P(1)
10P + 10 –
tw(DSH)
Case 2b: Memory accesses when DMAC is inactive
10
and tw(DSH)≥ 10P(1)
Case 3: Register accesses
10
10
td(DSL-HDV2)
th(DSH-HDV)R
tv(HYH-HDV)
td(DSH-HYL)
Delay time, DS low to HD valid for second byte of an HPI read
Hold time, HD valid after DS high, for a HPI read
Valid time, HD valid after HRDY high
ns
ns
ns
ns
0
2
8
Delay time, DS high to HRDY low(2)
Case 1a: Memory accesses when DMAC is active
18P + 6
36P + 6
10P + 6
in 16-bit mode(1)
Case 1b: Memory accesses when DMAC is active
in 32-bit mode(1)
Delay time, DS high to HRDY
high(2)
td(DSH-HYH)
ns
Case 2: Memory accesses when DMAC is inac-
tive(1)
Case 3: Write accesses to HPIC register(3)
6P + 6
td(HCS-HRDY)
td(COH-HYH)
td(COH-HTX)
Delay time, HCS low/high to HRDY low/high
Delay time, CLKOUT high to HRDY high
Delay time, CLKOUT high to HINT change
6
9
6
ns
ns
ns
Delay time, CLKOUT high to HDx output change. HDx is configured as a
general-purpose output
td(COH-GPIO)
5
ns
(1) DMAS stands for direct memory access controller. The HPI8 shares the internal DMA bus with the DMAC, thus HPI8 access times are
affected by DMAC activity.
(2) The HRDY output is always high when the HCS input is high, regardless of DS timings.
(3) This timing applies when writing a one to the DSPINT bit or HINT bit of the HPIC register. All other writes to the HPIC occur
asynchronously, and do not cause HRDY to be deasserted.
Electrical Specifications
87
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
Second Byte
First Byte
Second Byte
HAS
t
su(HBV-DSL)
t
su(HSL-DSL)
t
h(DSL-HBV)
HAD
(see Note A)
Valid
Valid
‡
su(HBV-DSL)
t
t
h(DSL-HBV)
(see Note B)
HBIL
HCS
t
w(DSH)
t
w(DSL)
HDS
t
d(DSH-HYH)
t
d(DSH-HYL)
HRDY
t
en(DSL-HD)
t
d(DSL-HDV2)
t
t
d(DSL-HDV1)
t
h(DSH-HDV)R
HD READ
Valid
Valid
Valid
t
su(HDV-DSH)
v(HYH-HDV)
t
h(DSH-HDV)W
HD WRITE
Valid
Valid
Valid
t
d(COH-HYH)
Processor
CLK
A. HAD refers to HCNTL0, HCNTL1, and HR/W.
B. When HAS is not used (HAS always high)
Figure 5-28. Using HDS to Control Accesses (HCS Always Low)
88
Electrical Specifications
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
HCS
HDS
t
d(HCS-HRDY)
HRDY
Figure 5-29. Using HCS to Control Accesses
CLKOUT
t
d(COH-HTX)
HINT
Figure 5-30. HINT Timing
In Figure 5-31, GPIOx refers to HD0, HD1, HD2, ...HD7, when the HD bus is configured for
general-purpose input/output (I/O).
CLKOUT
t
su(GPIO-COH)
t
h(GPIO-COH)
GPIOx Input Mode
(see Note A)
t
d(COH-GPIO)
GPIOx Output Mode
(see Note A)
Figure 5-31. GPIOx Timings
Electrical Specifications
89
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
5.5.11.2 HPI16 Mode
Table 5-34 and Table 5-35 assume testing over recommended operating conditions and P = 0.5 *
processor clock (see Figure 5-32 through Figure 5-34). In the following tables, DS refers to the logical OR
of HCS, HDS1, and HDS2, and HD refers to any of the HPI data bus pins (HD0, HD1, HD2, etc.). These
timings are shown assuming that HDS is the signal controlling the transfer. See the TMS320C54x DSP
Reference Set,Volume 5: Enhanced Peripherals (literature number SPRU302) for additional information.
Table 5-34. HPI16 Mode Timing Requirements
5416-120
5416-160
UNIT
MIN MAX
tsu(HBV-DSL)
th(DSL-HBV)
tsu(HAV-DSH)
tsu(HAV-DSL)
th(DSH-HAV)
tw(DSL)
Setup time, HR/W valid before DS falling edge
Hold time, HR/W valid after DS falling edge
Setup time, address valid before DS rising edge (write)
Setup time, address valid before DS falling edge (read)
Hold time, address valid after DS rising edge
Pulse duration, DS low
6
5
5
ns
ns
ns
ns
ns
ns
ns
–(4P– 6)(1)
1
30
tw(DSH)
Pulse duration, DS high
10
Reads 10P + 30(1)
Writes 10P + 10(1)
Reads 16P + 30(1)
Writes 16P + 10(1)
Reads 24P + 30(1)
Writes 24P + 10(1)
8
Memory accesses with no DMA activity.
Cycle time, DS rising edge to
next DS rising edge
Memory accesses with 16-bit DMA activ-
ity.
tc(DSH-DSH)
ns
Memory accesses with 32-bit DMA activ-
ity.
tsu(HDV-DSH)W
th(DSH-HDV)W
Setup time, HD valid before DS rising edge
Hold time, HD valid after DS rising edge, write
ns
ns
2
(1) P = 0.5 * processor clock.
90
Electrical Specifications
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
Table 5-35. HPI16 Mode Switching Characteristics
5416-120
5416-160
PARAMETER
Delay time, DS low to HD driven
UNIT
MIN
MAX
td(DSL-HDD)
0
10
Case 1a: Memory accesses initiated immediately following a write
when DMAC is active in 32-bit mode and tw(DSH) was < 26P
48P + 20 – tw(DSH)
24P + 20
Case 1b: Memory access not immediately following a write when
DMAC is active in 32-bit mode
Case 1c: Memory accesses initiated immediately following a write
when DMAC is active in 16-bit mode and tw(DSH) was < 18P
Delay time, DS
low to HD valid
for first word of
an HPI read
32P + 20 – tw(DSH)
16P + 20
ns
td(DSL-HDV1)
Case 1d: Memory accesses not immediately following a write when
DMAC is active in 16-bit mode
Case 2a: Memory accesses initiated immediately following a write
when DMAC is inactive and tw(DSH) was < 10P
20P + 20 – tw(DSH)
10P + 20
Case 2b: Memory accesses not immediately following a write when
DMAC is inactive
Memory writes when no DMA is active
10P + 5
16P + 5
24P + 5
Delay time, DS
td(DSH-HYH)
high to HRDY Memory writes with one or more 16-bit DMA channels active
ns
high
Memory writes with one or more 32-bit DMA channels active
tv(HYH-HDV)
th(DSH-HDV)R
td(COH-HYH)
td(DSL-HYL)
td(DSH-HYL)
Valid time, HD valid after HRDY high
Hold time, HD valid after DS rising edge, read
Delay time, CLKOUT rising edge to HRDY high
Delay time, DS low to HRDY low
7
ns
ns
ns
ns
ns
1
6
5
12
12
Delay time, DS high to HRDY low
HCS
t
w(DSH)
t
c(DSH−DSH)
HDS
t
t
su(HBV−DSL)
w(DSL)
t
su(HBV−DSL)
t
t
h(DSL−HBV)
h(DSL−HBV)
HR/W
t
su(HAV−DSL)
t
h(DSH−HAV)
HA[17:0]
Valid Address
Valid Address
t
h(DSH−HDV)R
t
d(DSL−HDV1)
t
t
h(DSH−HDV)R
d(DSL−HDV1)
Data
HD[15:0]
HRDY
Data
t
d(DSL−HDD)
t
d(DSL−HDD)
t
v(HYH−HDV)
t
v(HYH−HDV)
t
t
d(DSL−HYL)
d(DSL−HYL)
Figure 5-32. Nonmultiplexed Read Timings
Electrical Specifications
91
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
HCS
t
w(DSH)
t
c(DSH−DSH)
HDS
t
su(HBV−DSL)
t
su(HBV−DSL)
t
t
h(DSL−HBV)
h(DSL−HBV)
HR/W
t
su(HAV−DSH)
t
w(DSL)
t
h(DSH−HAV)
Valid Address
Valid Address
HA[17:0]
HD[15:0]
HRDY
t
t
su(HDV−DSH)W
su(HDV−DSH)W
t
h(DSH−HDV)W
t
h(DSH−HDV)W
Data Valid
Data Valid
t
d(DSH−HYH)
t
d(DSH−HYL)
Figure 5-33. Nonmultiplexed Write Timings
HRDY
t
d(COH−HYH)
CLKOUT
Figure 5-34. HRDY Relative to CLKOUT
92
Electrical Specifications
TMS320VC5416
Fixed-Point Digital Signal Processor
www.ti.com
SPRS095O–MARCH 1999–REVISED JANUARY 2005
6
Mechanical Data
The following mechanical package diagram(s) reflect the most current released mechanical data available
for the designated device(s).
6.1 Package Thermal Resistance Characteristics
Table 6-1provides the estimated thermal resistance characteristics for the recommended package types
used on the device.
Table 6-1. Thermal Resistance Characteristics
PARAMETER
RθJA
GGU PACKAGE
PGE PACKAGE
UNIT
°C/W
°C/W
38
5
56
5
RθJC
Mechanical Data
93
PACKAGE OPTION ADDENDUM
www.ti.com
27-Oct-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
Drawing
TMS320VC5416GGU120
TMS320VC5416GGU160
TMS320VC5416PGE120
ACTIVE
ACTIVE
ACTIVE
BGA
GGU
144
144
144
160
160
TBD
TBD
SNPB
SNPB
Level-3-220C-168HR
Level-3-220C-168HR
BGA
GGU
LQFP
PGE
60 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TMS320VC5416PGE160
TMS320VC5416ZGU120
TMS320VC5416ZGU160
TMSDVC5416GGUR160
ACTIVE
ACTIVE
ACTIVE
ACTIVE
LQFP
BGA
BGA
BGA
PGE
ZGU
ZGU
GGU
144
144
144
144
1
Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
160 Green (RoHS &
no Sb/Br)
SNAGCU
SNAGCU
SNPB
Level-3-260C-168HR
Level-3-260C-168HR
Level-3-220C-168HR
160 Green (RoHS &
no Sb/Br)
1000
TBD
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan
-
The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS
&
no Sb/Br)
-
please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
MECHANICAL DATA
MPBG021C – DECEMBER 1996 – REVISED MAY 2002
GGU (S–PBGA–N144)
PLASTIC BALL GRID ARRAY
12,10
11,90
SQ
9,60 TYP
0,80
N
M
L
K
J
H
G
F
E
D
C
B
A
A1 Corner
1
2
3
4
5
6
7
8
9 10 11 12 13
Bottom View
0,95
0,85
1,40 MAX
Seating Plane
0,10
0,55
0,45
0,08
0,45
0,35
4073221-2/C 12/01
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice
C. MicroStar BGAt configuration
MicroStar BGA is a trademark of Texas Instruments Incorporated.
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL DATA
MTQF017A – OCTOBER 1994 – REVISED DECEMBER 1996
PGE (S-PQFP-G144)
PLASTIC QUAD FLATPACK
108
73
109
72
0,27
M
0,08
0,17
0,50
0,13 NOM
144
37
1
36
Gage Plane
17,50 TYP
20,20
SQ
19,80
0,25
0,05 MIN
22,20
SQ
0°–7°
21,80
0,75
0,45
1,45
1,35
Seating Plane
0,08
1,60 MAX
4040147/C 10/96
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-026
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Audio
Amplifiers
amplifier.ti.com
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
Digital Control
Military
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/military
Interface
Logic
interface.ti.com
logic.ti.com
Power Mgmt
Microcontrollers
power.ti.com
Optical Networking
Security
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
microcontroller.ti.com
Telephony
Video & Imaging
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright 2005, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明