OPA333AMDCKREP [TI]
1.8-V MICROPOWER CMOS OPERATIONAL AMPLIFIERS ZERO-DRIFT SERIES; 1.8 V微功耗CMOS运算放大器零漂移系列
| 型号： | OPA333AMDCKREP |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 1.8-V MICROPOWER CMOS OPERATIONAL AMPLIFIERS ZERO-DRIFT SERIES |
| 文件： | 总19页 (文件大小：611K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
OPA333A-EP, OPA2333A-EP
www.ti.com ............................................................................................................................................................ SGLS383B–APRIL 2007–REVISED JUNE 2008
1.8-V MICROPOWER CMOS OPERATIONAL AMPLIFIERS
ZERO-DRIFT SERIES
1
FEATURES
•
•
•
•
•
•
•
Low Offset Voltage: 23 µV (Max)
0.01-Hz to 10-Hz Noise: 1.1 µVPP
Quiescent Current: 17 µA
SUPPORTS DEFENSE, AEROSPACE,
AND MEDICAL APPLICATIONS
•
•
•
•
Controlled Baseline
One Assembly/Test Site
One Fabrication Site
Available in Military (–55°C/125°C)
Temperature Range(1)
Single-Supply Operation
Supply Voltage: 1.8 V to 5.5 V
Rail-to-Rail Input/Output
MicroSize Packages: SC70 and SOT23
•
•
•
Extended Product Life Cycle
Extended Product-Change Notification
Product Traceability
APPLICATIONS
•
•
•
•
•
•
Transducer Applications
Temperature Measurements
Electronic Scales
Medical Instrumentation
Battery-Powered Instruments
Handheld Test Equipment
(1) Custom temperature ranges available
DCK PACKAGE
(TOP VIEW)
D PACKAGE
(TOP VIEW)
DBV PACKAGE
(TOP VIEW)
+IN
V–
V+
1
2
3
5
4
OUT
V–
V+
1
2
3
5
4
OUT A
–IN A
+IN A
V–
V+
1
2
3
4
8
7
6
5
OUT B
–IN B
+IN B
–IN
OUT
+IN
–IN
0.1Hz TO 10Hz NOISE
1s/div
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2007–2008, Texas Instruments Incorporated
OPA333A-EP, OPA2333A-EP
SGLS383B–APRIL 2007–REVISED JUNE 2008 ............................................................................................................................................................ www.ti.com
DESCRIPTION/ORDERING INFORMATION
The OPA333A series of CMOS operational amplifiers uses a proprietary auto-calibration technique to
simultaneously provide very low offset voltage (10 µV max) and near-zero drift over time and temperature. These
miniature, high-precision, low-quiescent-current amplifiers offer high-impedance inputs that have
a
common-mode range 100 mV beyond the rails, and rail-to-rail output that swings within 50 mV of the rails. Single
or dual supplies as low as 1.8 V (±0.9 V) and up to 5.5 V (±2.75 V) may be used. They are optimized for
low-voltage single-supply operation.
The OPA333A family offers excellent common-mode rejection ratio (CMRR) without the crossover associated
with traditional complementary input stages. This design results in superior performance for driving
analog-to-digital converters (ADCs) without degradation of differential linearity.
The OPA333A (single version) is available in the SC70-5 and SOT23-5 packages. The OPA2333A (dual version)
is offered in the SO-8 package. All versions are specified for operation from –55°C to 125°C.
ORDERING INFORMATION(1)
PRODUCT
PACKAGE-LEAD
SOT23-5
SC70-5
PACKAGE DESIGNATOR
PACKAGE MARKING(2)
OPA333AMDBVREP
OPA333AMDCKREP
OPA2333AMDREP
DBV
DCK
D
OBYM
CHQ
SO-8
2333EP
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
Web site at www.ti.com.
(2) Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
PIN CONFIGURATIONS
OPA2333A
OPA333A
OPA333A
OUT A
1
2
3
4
8
7
6
5
V+
OUT
1
2
3
5
4
V+
+IN
1
2
3
5
4
V+
A
−
OUT B
IN A
−
V
−
V
B
−
+IN A
IN B
−
+IN
IN
−
IN
OUT
−
V
+IN B
SOT23-5
SC70-5
SO-8
Absolute Maximum Ratings(1)
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
UNIT
Supply voltage
7
V
V
Signal input terminals, voltage(2)
Output short circuit(3)
–0.3
(V+) + 0.3
Continuous
125
Operating temperature range
Storage temperature range
Junction temperature
–55
–65
°C
°C
°C
150(4)
150
Human-Body Model (HBM)
4000
ESD rating
V
Charged-Device Model (CDM)
1000
(1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) Input terminals are diode clamped to the power-supply rails. Input signals that can swing more than 0.3 V beyond the supply rails should
be current limited to 10 mA or less.
(3) Short circuit to ground, one amplifier per package
(4) Long-term high-temperature storage and/or extended use at maximum recommended operating conditions may result in a reduction of
overall device life. See http://www.ti.com/ep_quality for additional information on enhanced plastic packaging.
2
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA333A-EP OPA2333A-EP
OPA333A-EP, OPA2333A-EP
www.ti.com ............................................................................................................................................................ SGLS383B–APRIL 2007–REVISED JUNE 2008
Electrical Characteristics: VS = 1.8 V to 5.5 V
Boldface limits apply over the specified temperature range, TA = –55°C to 125°C. At TA = 25°C, RL = 10 kΩ connected to
VS/2, VCM = VS/2, and VOUT = VS/2 (unless otherwise noted).
PARAMETER
OFFSET VOLTAGE
TEST CONDITIONS
MIN
TYP
2
MAX
UNIT
Input offset voltage
over temperature
vs temperature
VOS
VS = 5 V
10
µV
µV
22
dVOS/dT
PSRR
0.02
µV/°C
µV/V
vs power supply
Long-term stability(1)
Channel separation, dc
INPUT BIAS CURRENT
Input bias current
over Temperature
Input offset current
NOISE
VS = 1.8 V to 5.5 V
1
(1)
6
0.1
µV/V
IB
±70
±150
±140
±200
±400
pA
pA
pA
IOS
Input voltage noise,
f = 0.01 Hz to 1 Hz
0.3
µVPP
Input voltage noise,
f = 0.1 Hz to 10 Hz
1.1
µVPP
Input current noise, f = 10 Hz
INPUT VOLTAGE RANGE
Common mode voltage range
in
100
fA/√Hz
VCM
(V–) – 0.1
(V+) + 0.1
V
Common-Mode Rejection
Ratio
CMRR
(V–) – 0.1 V < VCM < (V+) + 0.1 V
102
130
dB
INPUT CAPACITANCE
Differential
2
4
pF
pF
Common mode
OPEN-LOOP GAIN
(V–) + 100 mV < VO < (V+) – 100 mV,
Open-loop voltage gain
AOL
104
130
dB
RL = 10 kΩ
FREQUENCY RESPONSE
Gain-bandwidth product
Slew rate
GBW
SR
CL = 100 pF
G = 1
350
kHz
0.16
V/µs
OUTPUT
Voltage output swing from rail
over temperature
Short-circuit current
Capacitive load drive
RL = 10 kΩ
RL = 10 kΩ
30
±5
50
mV
mV
mA
85
ISC
CL
(2)Open-loop output
impedance
f = 350 kHz, IO = 0
2
kΩ
POWER SUPPLY
Specified voltage range
VS
IQ
1.8
5.5
25
30
V
Quiescent current per
amplifier
IO = 0
17
µA
over temperature
Turn-on time
µA
µs
VS = 5 V
100
TEMPERATURE RANGE
Specified range
–55
125
°C
(1) 300-hour life test at 150°C demonstrated randomly distributed variation of approximately 1 µV
(2) See Typical Characteristics
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Link(s): OPA333A-EP OPA2333A-EP
OPA333A-EP, OPA2333A-EP
SGLS383B–APRIL 2007–REVISED JUNE 2008 ............................................................................................................................................................ www.ti.com
Electrical Characteristics: VS = 1.8 V to 5.5 V (continued)
Boldface limits apply over the specified temperature range, TA = –55°C to 125°C. At TA = 25°C, RL = 10 kΩ connected to
VS/2, VCM = VS/2, and VOUT = VS/2 (unless otherwise noted).
PARAMETER
TEST CONDITIONS
MIN
–55
–65
TYP
MAX
125
UNIT
°C
Operating range
Storage range
150
°C
Thermal resistance
SOT23-5
θJA
200
150
250
°C/W
°C/W
°C/W
SO-8
SC70-5
TYPICAL CHARACTERISTICS
At TA = 25°C, VS = 5 V, and CL = 0 pF (unless otherwise noted).
OFFSET VOLTAGE DRIFT PRODUCTION DISTRIBUTION
OFFSET VOLTAGE PRODUCTION DISTRIBUTION
µ
Offset Voltage ( V)
µ
_
Offset Voltage Drift ( V/ C)
OPEN−LOOP GAIN vs FREQUENCY
COMMON−MODE REJECTION RATIO vs FREQUENCY
120
100
80
60
40
20
0
250
200
150
100
50
140
120
100
80
60
0
40
−
−
50
20
−
20
100
0
10
100
1k
10k
100k
1M
1
10
100
1k
10k
100k
1M
Frequency (Hz)
Frequency (Hz)
4
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA333A-EP OPA2333A-EP
OPA333A-EP, OPA2333A-EP
www.ti.com ............................................................................................................................................................ SGLS383B–APRIL 2007–REVISED JUNE 2008
TYPICAL CHARACTERISTICS (continued)
POWER−SUPPLY REJECTION RANGE vs FREQUENCY
OUTPUT VOLTAGE SWING vs OUTPUT CURRENT
120
100
80
60
40
20
0
3
2
1
0
1
2
3
±
±
VS
VS
=
=
2.75V
0.9V
+PSRR
−
_
40 C
−
PSRR
_
+25 C
_
+125 C
_
+25 C
−
_
40 C
−
−
−
_
+125 C
_
+25 C
−
_
40 C
1
10
100
1k
10k
100k
1M
0
1
2
3
4
5
6
7
8
9
10
Frequency (Hz)
Output Current (mA)
INPUT BIAS CURRENT vs TEMPERATURE
INPUT BIAS CURRENT vs COMMON−MODE VOLTAGE
100
200
150
100
50
VS = 5.5V
VS = 1.8V
80
60
40
20
0
−
IB
−
IB
−
IB
VS = 5V
0
+IB
−
−
−
−
20
40
60
80
−
50
−
−
−
100
150
200
+IB
+IB
−
100
−
−
0
1
2
3
4
5
50
25
0
25
50
75
100
125
_
Temperature ( C)
Common−Mode Voltage (V)
QUIESCENT CURRENT vs TEMPERATURE
LARGE−SIGNAL STEP RESPONSE
25
20
15
10
5
G = 1
RL = 10k
Ω
V
S = 5.5V
VS = 1.8V
0
−
−
25
50
0
25
50
75
100
125
µ
Time (50 s/div)
_
Temperature ( C)
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Link(s): OPA333A-EP OPA2333A-EP
OPA333A-EP, OPA2333A-EP
SGLS383B–APRIL 2007–REVISED JUNE 2008 ............................................................................................................................................................ www.ti.com
TYPICAL CHARACTERISTICS (continued)
SMALL−SIGNAL STEP RESPONSE
POSITIVE OVER−VOLTAGE RECOVERY
G = +1
Ω
RL = 10k
0
Input
Output
Ω
10k
+2.5V
Ω
1k
0
OPA333
−
2.5V
µ
Time (5 s/div)
µ
Time (50 s/div)
SETTLING TIME vs CLOSED−LOOP GAIN
NEGATIVE OVER−VOLTAGE RECOVERY
600
500
400
300
200
100
0
4V Step
Input
0
0
Ω
10k
+2.5V
Ω
1k
0.001%
0.01%
Output
OPA333
−
2.5V
1
10
100
µ
Time (50 s/div)
Gain (dB)
SMALL−SIGNAL OVERSHOOT vs LOAD CAPACITANCE
0.1Hz TO 10Hz NOISE
40
35
30
25
20
15
10
5
0
10
100
1000
1s/div
Load Capacitance (pF)
6
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA333A-EP OPA2333A-EP
OPA333A-EP, OPA2333A-EP
www.ti.com ............................................................................................................................................................ SGLS383B–APRIL 2007–REVISED JUNE 2008
TYPICAL CHARACTERISTICS (continued)
CURRENT AND VOLTAGE NOISE SPECTRAL DENSITY
vs FREQUENCY
1000
100
10
1000
100
10
Continues with no 1/f (flicker) noise.
Current Noise
Voltage Noise
1
10
100
1k
10k
Frequency (Hz)
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Link(s): OPA333A-EP OPA2333A-EP
OPA333A-EP, OPA2333A-EP
SGLS383B–APRIL 2007–REVISED JUNE 2008 ............................................................................................................................................................ www.ti.com
APPLICATION INFORMATION
The OPA333A and OPA2333A are unity-gain stable and free from unexpected output phase reversal. They use a
proprietary auto-calibration technique to provide low offset voltage and very low drift over time and temperature.
For lowest offset voltage and precision performance, circuit layout and mechanical conditions should be
optimized. Avoid temperature gradients that create thermoelectric (Seebeck) effects in the thermocouple
junctions formed from connecting dissimilar conductors. These thermally-generated potentials can be made to
cancel by ensuring they are equal on both input terminals. Other layout and design considerations include:
•
•
•
Use low thermoelectric-coefficient conditions (avoid dissimilar metals)
Thermally isolate components from power supplies or other heat sources
Shield op amp and input circuitry from air currents, such as cooling fans
Following these guidelines will reduce the likelihood of junctions being at different temperatures, which can cause
thermoelectric voltages of 0.1 µV/°C or higher, depending on materials used.
Operating Voltage
The OPA333A and OPA2333A op amps operate over a power-supply range of 1.8 V to 5.5 V (±0.9 V to
±2.75 V). Supply voltages higher than 7 V (absolute maximum) can permanently damage the device. Parameters
that vary over supply voltage or temperature are shown in the Typical Characteristics section of this data sheet.
Input Voltage
The OPA333A and OPA2333A input common-mode voltage range extends 0.1 V beyond the supply rails. The
OPA333A is designed to cover the full range without the troublesome transition region found in some other
rail-to-rail amplifiers.
Normally, input bias current is about 70 pA; however, input voltages exceeding the power supplies can cause
excessive current to flow into or out of the input pins. Momentary voltages greater than the power supply can be
tolerated if the input current is limited to 10 mA. This limitation is easily accomplished with an input resistor(see
Figure 1).
Current−limiting resistor
required if input voltage
exceeds supply rails by
≥
0.5V.
+5V
IOVERLOAD
10mA max
VOUT
OPA333A
VIN
Ω
5k
Figure 1. Input Current Protection
Internal Offset Correction
The OPA333A and OPA2333A op amps use an auto-calibration technique with a time-continuous 350-kHz op
amp in the signal path. This amplifier is zero corrected every 8 µs using a proprietary technique. Upon power up,
the amplifier requires approximately 100 µs to achieve specified VOS accuracy. This design has no aliasing or
flicker noise.
8
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA333A-EP OPA2333A-EP
OPA333A-EP, OPA2333A-EP
www.ti.com ............................................................................................................................................................ SGLS383B–APRIL 2007–REVISED JUNE 2008
Achieving Output Swing to the Op Amp Negative Rail
Some applications require output voltage swings from 0 V to a positive full-scale voltage (such as 2.5 V) with
excellent accuracy. With most single-supply op amps, problems arise when the output signal approaches 0 V,
near the lower output swing limit of a single-supply op amp. A good single-supply op amp may swing close to
single-supply ground, but will not reach ground. The output of the OPA333A and OPA2333A can be made to
swing to ground, or slightly below, on a single-supply power source. To do so requires the use of another resistor
and an additional, more negative, power supply than the op amp negative supply. A pulldown resistor may be
connected between the output and the additional negative supply to pull the output down below the value that the
output would otherwise achieve (see Figure 2).
V+ = +5V
OPA333A
VOUT
VIN
Ω
RP = 20k
−
Op Amp V = Gnd
−
5V
Additional
Negative
Supply
Figure 2. VOUT Range to Ground
The OPA333A and OPA2333A have an output stage that allows the output voltage to be pulled to its negative
supply rail, or slightly below, using the technique previously described. This technique only works with some
types of output stages. The OPA333A and OPA2333A have been characterized to perform with this technique;
however, the recommended resistor value is approximately 20 kΩ. Note that this configuration will increase the
current consumption by several hundreds of microamps. Accuracy is excellent down to 0 V and as low as
–2 mV. Limiting and nonlinearity occurs below –2 mV, but excellent accuracy returns as the output is again
driven above –2 mV. Lowering the resistance of the pulldown resistor allows the op amp to swing even further
below the negative rail. Resistances as low as 10 kΩ can be used to achieve excellent accuracy down to
–10 mV.
General Layout Guidelines
Attention to good layout practices is always recommended. Keep traces short and, when possible, use a printed
circuit board (PCB) ground plane with surface-mount components placed as close to the device pins as possible.
Place a 0.1-µF capacitor closely across the supply pins. These guidelines should be applied throughout the
analog circuit to improve performance and provide benefits, such as reducing the electromagnetic interference
(EMI) susceptibility.
Operational amplifiers vary in their susceptibility to radio frequency interference (RFI). RFI can generally be
identified as a variation in offset voltage or dc signal levels with changes in the interfering RF signal. The
OPA333A has been specifically designed to minimize susceptibility to RFI and demonstrates remarkably low
sensitivity compared to previous-generation devices. Strong RF fields may still cause varying offset levels.
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Link(s): OPA333A-EP OPA2333A-EP
OPA333A-EP, OPA2333A-EP
SGLS383B–APRIL 2007–REVISED JUNE 2008 ............................................................................................................................................................ www.ti.com
4.096V
REF3140
+5V
+
R9
µ
0.1 F
Ω
150k
R1
Ω
6.04k
R5
Ω
+5V
0.1 F
31.6k
D1
µ
R2
2.94k
R2
Ω
Ω
549
−
−
+
+
VO
OPA333A
R6
K−Type
Thermocouple
Ω
200
R3
R4
6.04k
Zero Adj.
µ
_
40.7 V/
C
Ω
Ω
60.4
Figure 3. Temperature Measurement
Figure 4 shows the basic configuration for a bridge amplifier.
VEX
R1
+5V
R
R
R
R
VOUT
OPA333A
R1
VREF
Figure 4. Single Op-Amp Bridge Amplifier
A low-side current shunt monitor is shown in Figure 5. RN are operational resistors used to isolate the ADS1100
from the noise of the digital I2C bus. Since the ADS1100 is a 16-bit converter, a precise reference is essential for
maximum accuracy. If absolute accuracy is not required, and the 5-V power supply is sufficiently stable, the
REF3130 may be omitted.
10
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA333A-EP OPA2333A-EP
OPA333A-EP, OPA2333A-EP
www.ti.com ............................................................................................................................................................ SGLS383B–APRIL 2007–REVISED JUNE 2008
3V
REF3130
+5V
R2
Load
R1
Ω
Ω
Ω
4.99k
49.9k
R6
71.5k
RN
Ω
V
Ω
56
RSHUNT
ILOAD
OPA333A
Ω
1
R3
4.99k
R4
RN
I2C
ADS1100
Ω
48.7k
Ω
56
R7
1.18k
(PGA Gain = 4)
FS = 3.0V
Stray Ground−Loop Resistance
Ω
NOTE: 1% resistors provide adequate common−mode rejection at small ground−loop errors.
Figure 5. Low-Side Current Monitor
RG
zener(1)
V+
RSHUNT
(2)
R1
MOSFET rated to
stand−off supply voltage
such as BSS84 for
up to 50V.
Ω
OPA333A
10k
+5V
V+
Two zener
biasing methods
are shown.(3)
Output
RBIAS
Load
RL
(1) zener rated for op amp supply capability (that is, 5.1V for OPA333).
(2) Current−limiting resistor.
NOTES:
(3) Choose zener biasing resistor or dual NMOSFETS (FDG6301N, NTJD4001N, or Si1034)
Figure 6. High-Side Current Monitor
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Link(s): OPA333A-EP OPA2333A-EP
OPA333A-EP, OPA2333A-EP
SGLS383B–APRIL 2007–REVISED JUNE 2008 ............................................................................................................................................................ www.ti.com
V1
INA152
−
In
OPA333
2
3
5
6
100 kΩ
R2
60 kΩ
1 MΩ
VO
R1
3V
NTC
Thermistor
R2
OPA333
1 MΩ
1
OPA333
V2
+In
−
VO = (1 + 2R2/R1) (V2 V1)
Figure 7. Thermistor Measurement
Figure 8. Precision Instrumentation Amplifier
+VS
fLPF = 150Hz
C4
1.06nF
R1
100k
1/2
OPA2333
Ω
Ω
Ω
RA
R14
GTOT = 1kV/V
Ω
1M
R7
100k
+VS
7
Ω
Ω
+VS
GINA = 5
6
R12
R6
100k
+VS
3
2
Ω
5k
Ω
R2
100k
1/2
OPA2333
INA321(1)
1
VOUT
GOPA = 200
OPA333
LL
4
5
C3
µ
1 F
R13
R8
100k
Ω
318k
+VS
+VS
dc
ac
R3
100k
1/2
OPA2333
1/2
Wilson
VCENTRAL
OPA2333
LA
C1
47pF
(RA + LA + LL)/3
fHPF = 0.5Hz
(provides ac signal coupling)
1/2 VS
R5
Ω
390k
+VS
VS = +2.7V to +5.5V
BW = 0.5Hz to 150Hz
R9
+VS
Ω
20k
R4
1/2
Ω
100k
OPA2333
1/2
OPA2333
RL
Inverted
VCM
+VS
R10
NOTE: (1) Other instrumentation amplifiers can be used,
such as the INA326, which has lower noise,
but higher quiescent current.
Ω
1M
1/2 VS
R11
C2
Ω
1M
µ
0.64 F
fO = 0.5Hz
Figure 9. Single-Supply, Very-Low-Power ECG Circuit
12
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA333A-EP OPA2333A-EP
PACKAGE OPTION ADDENDUM
www.ti.com
15-Aug-2008
PACKAGING INFORMATION
Orderable Device
OPA2333AMDREP
OPA333AMDBVREP
OPA333AMDCKREP
V62/07633-01XE
Status (1)
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
Drawing
SOIC
D
8
5
5
5
5
8
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
SOT-23
SC70
DBV
DCK
DBV
DCK
D
3000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
3000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
SOT-23
SC70
3000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
V62/07633-01YE
3000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
V62/07633-02ZE
SOIC
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Aug-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0 (mm)
B0 (mm)
K0 (mm)
P1
W
Pin1
Diameter Width
(mm) W1 (mm)
(mm) (mm) Quadrant
OPA2333AMDREP
OPA333AMDBVREP
OPA333AMDCKREP
SOIC
SOT-23
SC70
D
8
5
5
2500
3000
3000
330.0
179.0
179.0
12.4
8.4
6.4
3.2
2.2
5.2
3.2
2.5
2.1
1.4
1.2
8.0
4.0
4.0
12.0
8.0
Q1
Q3
Q3
DBV
DCK
8.4
8.0
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Aug-2008
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
OPA2333AMDREP
OPA333AMDBVREP
OPA333AMDCKREP
SOIC
SOT-23
SC70
D
8
5
5
2500
3000
3000
346.0
195.0
195.0
346.0
200.0
200.0
29.0
45.0
45.0
DBV
DCK
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
Logic
Military
Power Mgmt
Microcontrollers
RFID
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
RF/IF and ZigBee® Solutions www.ti.com/lprf
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明