MAX202IPWG4 [TI]
5-V Dual RS-232 Line Driver/Receiver with +/-15 kV ESD Protection 16-TSSOP -40 to 85;
| 型号： | MAX202IPWG4 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 5-V Dual RS-232 Line Driver/Receiver with +/-15 kV ESD Protection 16-TSSOP -40 to 85 驱动 光电二极管 接口集成电路 驱动器 |
| 文件： | 总20页 (文件大小：772K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MAX202
5-V DUAL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS576E–JULY 2003–REVISED APRIL 2007
FEATURES
•
ESD Protection for RS-232 Bus Pins
±15-kV – Human-Body Model
D, DW, N, OR PW PACKAGE
(TOP VIEW)
–
•
Meets or Exceeds the Requirements of
TIA/EIA-232-F and ITU v.28 Standards
1
2
3
4
5
6
7
8
C1+
V+
VCC
15 GND
16
•
•
•
•
Operates at 5-V VCC Supply
Operates Up to 120 kbit/s
14
13
12
11
10
9
C1-
DOUT1
RIN1
C2+
C2-
External Capacitors . . . 4 × 0.1 µF
ROUT1
DIN1
Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
V-
DOUT2
RIN2
DIN2
ROUT2
APPLICATIONS
•
•
•
•
•
•
Battery-Powered Systems
PDAs
Notebooks
Laptops
Palmtop PCs
Hand-Held Equipment
DESCRIPTION/ORDERING INFORMATION
The MAX202 device consists of two line drivers, two line receivers, and a dual charge-pump circuit with ±15-kV
ESD protection pin to pin (serial-port connection pins, including GND). The device meets the requirements of
TIA/EIA-232-F and provides the electrical interface between an asynchronous communication controller and the
serial-port connector. The charge pump and four small external capacitors allow operation from a single 5-V
supply. The device operates at data signaling rates up to 120 kbit/s and a maximum of 30-V/µs driver output
slew rate.
ORDERING INFORMATION
TA
PACKAGE(1)(2)
ORDERABLE PART NUMBER
MAX202CN
TOP-SIDE MARKING
MAX202CN
PDIP – N
SOIC – D
Tube of 25
Tube of 40
Reel of 2500
Tube of 40
Reel of 2000
Tube of 90
Reel of 2000
Tube of 25
Tube of 40
Reel of 2500
Tube of 40
Reel of 2000
Tube of 90
Reel of 2000
MAX202CD
MAX202C
MAX202C
MAX202CDR
MAX202CDW
MAX202CDWR
MAX202CPW
MAX202CPWR
MAX202IN
0°C to 70°C
SOIC – DW
TSSOP – PW
PDIP – N
MA202C
MAX202IN
MAX202I
MAX202ID
SOIC – D
MAX202IDR
–40°C to 85°C
MAX202IDW
SOIC – DW
MAX202I
MB202I
MAX202IDWR
MAX202IPW
TSSOP – PW
MAX202IPWR
(1) Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
(2) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Copyright © 2003–2007, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
MAX202
5-V DUAL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS576E–JULY 2003–REVISED APRIL 2007
Function Tables
xxx
EACH DRIVER(1)
INPUT
OUTPUT
DIN
DOUT
L
H
L
H
(1) H = high level, L = low level
EACH RECEIVER(1)
INPUT
RIN
OUTPUT
ROUT
L
H
H
L
Open
H
(1) H = high level, L = low level,
Open = input disconnected or
connected driver off
LOGIC DIAGRAM (POSITIVE LOGIC)
11
10
12
9
14
DIN1
DIN2
DOUT1
DOUT2
RIN1
7
13
8
ROUT1
ROUT2
RIN2
2
Submit Documentation Feedback
MAX202
5-V DUAL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS576E–JULY 2003–REVISED APRIL 2007
Absolute Maximum Ratings(1)
over operating free-air temperature range (unless otherwise noted)
MIN
–0.3
MAX
UNIT
VCC
V+
Supply voltage range(2)
Positive charge pump voltage range(2)
Negative charge pump voltage range(2)
6
14
V
V
V
VCC – 0.3
–14
V–
0.3
Drivers
–0.3
V+ + 0.3
±30
VI
Input voltage range
V
V
Receivers
Drivers
V – –0.3
–0.3
V+ + 0.3
VCC + 0.3
Continuous
73
VO
Output voltage range
Short-circuit duration
Receivers
DOUT
D package
DW package
N package
PW package
57
θJA
Package thermal impedance(3)(4)
°C/W
67
108
TJ
Operating virtual junction temperature
Storage temperature range
150
°C
°C
Tstg
–65
150
(1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltages are with respect to network GND.
(3) Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient
temperature is PD = (TJ(max) – TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
(4) The package thermal impedance is calculated in accordance with JESD 51-7.
Recommended Operating Conditions(1)
(see Figure 4)
MIN
4.5
2
NOM
MAX UNIT
Supply voltage
5
5.5
V
V
V
VIH
VIL
Driver high-level input voltage
Driver low-level input voltage
Driver input voltage
DIN
DIN
DIN
0.8
5.5
30
70
85
0
–30
0
VI
V
Receiver input voltage
MAX202C
MAX202I
TA
Operating free-air temperature
°C
–40
(1) Test conditions are C1–C4 = 0.1 µF at VCC = 5 V ±0.5 V.
Electrical Characteristics(1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 4)
PARAMETER
Suppy current
TEST CONDITIONS
No load, VCC = 5 V
MIN
TYP(2)
MAX
UNIT
ICC
8
15
mA
(1) Test conditions are C1–C4 = 0.1 µF at VCC = 5 V ± 0.5 V.
(2) All typical values are at VCC = 5 V, and TA = 25°C.
3
Submit Documentation Feedback
MAX202
5-V DUAL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS576E–JULY 2003–REVISED APRIL 2007
DRIVER SECTION
Electrical Characteristics(1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 4)
PARAMETER
High-level output voltage
Low-level output voltage
High-level input current
Low-level input current
Short-circuit output current
Output resistance
TEST CONDITIONS
DOUT at RL = 3 kΩ to GND, DIN = GND
DOUT at RL = 3 kΩ to GND, DIN = VCC
VI = VCC
MIN TYP(2)
MAX UNIT
VOH
VOL
IIH
5
9
–9
V
V
–5
15
200
–200
±60
µA
µA
mA
Ω
IIL
VI at 0 V
–15
±10
(3)
IOS
rO
VCC = 5.5 V
VO = 0 V
VCC, V+, and V– = 0 V
VO = ±2 V
300
(1) Test conditions are C1–C4 = 0.1 µF at VCC = 5 V ± 0.5 V.
(2) All typical values are at VCC = 5 V, and TA = 25°C.
(3) Short-circuit durations should be controlled to prevent exceeding the device absolute power-dissipation ratings, and not more than one
output should be shorted at a time.
Switching Characteristics(1)
over recommended ranges of suply voltage and operating free-air temperature (unless otherwise noted) (see Figure 4)
PARAMETER
TEST CONDITIONS
MIN TYP(2)
MAX UNIT
CL = 50 to 1000 pF,
RL = 3 kΩ to 7 kΩ,
See Figure 1
Maximum data rate
120
kbit/s
One DOUT switching,
CL = 2500 pF,
RL = 3 kΩ,
Propagation delay time, low- to
high-level output
tPLH(D)
tPHL(D)
tsk(p)
2
2
µs
µs
ns
All drivers loaded,
CL = 2500 pF,
See Figure 1
RL = 3 kΩ,
Propagation delay time, high- to
low-level output
All drivers loaded,
CL = 150 to 2500 pF,
See Figure 1
RL = 3 kΩ to 7 kΩ,
See Figure 2
Pulse skew(3)
300
CL = 50 to 1000 pF,
VCC = 5 V
RL = 3 kΩ to 7 kΩ,
Slew rate, transition region
(see Figure 1)
SR(tr)
3
6
30
V/µs
(1) Test conditions are C1–C4 = 0.1 µF at VCC = 5 V ± 0.5 V.
(2) All typical values are at VCC = 5 V, and TA = 25°C.
(3) Pulse skew is defined as |tPLH - tPHL| of each channel of the same device.
ESD Protection
PIN
TEST CONDITIONS
TYP
UNIT
DOUT, RIN
Human-body model
±15
kV
4
Submit Documentation Feedback
MAX202
5-V DUAL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS576E–JULY 2003–REVISED APRIL 2007
RECEIVER SECTION
Electrical Characteristics(1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (seeFigure 4)
PARAMETER
TEST CONDITIONS
IOH = –1 mA
MIN
3.5 VCC – 0.4
TYP(2)
MAX UNIT
VOH
VOL
VIT+
VIT–
Vhys
ri
High-level output voltage
V
Low-level output voltage
IOL = 1.6 mA
VCC = 5 V,
VCC = 5 V,
0.4
2.4
V
V
Positive-going input threshold voltage
Negative-going input threshold voltage
TA = 25°C
TA = 25°C
1.7
0.8
0.2
3
1.2
0.5
5
V
Input hysteresis (VIT+ – VIT–
)
1
7
V
Input resistance
VI = ±3 V to ±25 V
kΩ
(1) Test conditions are C1–C4 = 0.1 µF at VCC = 5 V ± 0.5 V.
(2) All typical values are at VCC = 5 V, and TA = 25°C.
Switching Characteristics(1)
over recommended ranges of suply voltage and operating free-air temperature (unless otherwise noted) (see Figure 3)
PARAMETER
TEST CONDITIONS
CL = 150 pF
MIN
TYP(2)
0.5
MAX
10
UNIT
µs
tPLH(R)
tPHL(R)
tsk(p)
Propagation delay time, low- to high-level output
Propagation delay time, high- to low-level output
Pulse skew(3)
CL = 150 pF
0.5
10
µs
300
ns
(1) Test conditions are C1–C4 = 0.1 µF at VCC = 5 V ± 0.5 V.
(2) All typical values are at VCC = 5 V, and TA = 25°C.
(3) Pulse skew is defined as |tPLH - tPHL| of each channel of the same device.
5
Submit Documentation Feedback
MAX202
5-V DUAL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS576E–JULY 2003–REVISED APRIL 2007
PARAMETER MEASUREMENT INFORMATION
3 V
0 V
tPLH (D)
VOH
VOL
Input
1.5 V
1.5 V
RS-232
Output
Generator
50 W
(see Note B)
tPHL (D)
CL
(see Note A)
RL
3 V
–3 V
3 V
–3 V
Output
TEST CIRCUIT
VOLTAGE WAVEFORMS
6 V
tPHL(D) or tPLH(D)
SR(tf) =
NOTES: A. CL includes probe and jig capacitance.
B. The pulse generator has the following characteristics: PRR = 120 kbit/s, ZO = 50 W, 50% duty cycle, tr £ 10 ns, tf £ 10 ns.
Figure 1. Driver Slew Rate
3 V
RS-232
Output
1.5 V
1.5 V
Input
0 V
tPLH (D)
Generator
50 W
(see Note B)
CL
(see Note A)
tPHL (D)
RL
VOH
VOL
50%
50%
Output
TEST CIRCUIT
NOTES: A. CL includes probe and jig capacitance.
VOLTAGE WAVEFORMS
B. The pulse generator has the following characteristics: PRR = 120 kbit/s, ZO = 50 W, 50% duty cycle, tr £ 10 ns, tf £ 10 ns.
Figure 2. Driver Pulse Skew
3 V
Input
1.5 V
1.5 V
–3 V
Output
Generator
50 W
(see Note B)
tPHL (R)
tPLH (R)
CL
(see Note A)
VOH
VOL
50%
50%
Output
TEST CIRCUIT
VOLTAGE WAVEFORMS
NOTES: A. CL includes probe and jig capacitance.
B. The pulse generator has the following characteristics: ZO = 50 W, 50% duty cycle, tr £ 10 ns, tf £ 10 ns.
Figure 3. Receiver Propagation Delay Times
6
Submit Documentation Feedback
MAX202
5-V DUAL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS576E–JULY 2003–REVISED APRIL 2007
APPLICATION INFORMATION
1
2
3
4
16
15
VCC
C1+
V+
+
–
CBYPASS
= 0.1 mF,
C1
0.1 mF,
6.3 V
+
–
C3†
0.1 mF
16 V
GND
+
–
14
13
DOUT1
RIN1
C1–
C2+
C2–
V–
5 kW
C2
+
–
0.1 mF,
16 V
5
6
7
12
11
ROUT1
DIN1
C4
–
+
0.1 mF,
16 V
10
9
DOUT2
DIN2
8
RIN2
ROUT2
5 kW
†
C3 can be connected to VCC or GND.
NOTES: A . Resistor values shown are nominal.
B . Nonpolarized ceramic capacitors are acceptable. If polarized tantalum or electrolytic capacitors are used, they should be
connected as shown.
Figure 4. Typical Operating Circuit and Capacitor Values
Capacitor Selection
The capacitor type used for C1–C4 is not critical for proper operation. The MAX202 requires 0.1-µF capacitors,
although capacitors up to 10 µF can be used without harm. Ceramic dielectrics are suggested for the 0.1-µF
capacitors. When using the minimum recommended capacitor values, make sure the capacitance value does
not degrade excessively as the operating temperature varies. If in doubt, use capacitors with a larger (e.g., 2×)
nominal value. The capacitors' effective series resistance (ESR), which usually rises at low temperatures,
influences the amount of ripple on V+ and V–.
Use larger capacitors (up to 10 µF) to reduce the output impedance at V+ and V–.
Bypass VCC to ground with at least 0.1 µF. In applications sensitive to power-supply noise generated by the
charge pumps, decouple VCC to ground with a capacitor the same size as (or larger than) the charge-pump
capacitors (C1–C4).
ESD Protection
TI MAX202 devices have standard ESD protection structures incorporated on the pins to protect against
electrostatic discharges encountered during assembly and handling. In addition, the RS232 bus pins (driver
outputs and receiver inputs) of these devices have an extra level of ESD protection. Advanced ESD structures
were designed to successfully protect these bus pins against ESD discharge of ±15-kV when powered down.
7
Submit Documentation Feedback
MAX202
5-V DUAL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS576E–JULY 2003–REVISED APRIL 2007
APPLICATION INFORMATION (continued)
ESD Test Conditions
Stringent ESD testing is performed by TI, based on various conditions and procedures. Please contact TI for a
reliability report that documents test setup, methodology, and results.
Human-Body Model (HBM)
The HBM of ESD testing is shown in Figure 5. Figure 6 shows the current waveform that is generated during a
discharge into a low impedance. The model consists of a 100-pF capacitor, charged to the ESD voltage of
concern, and subsequently discharged into the device under test (DUT) through a 1.5-kΩ resistor.
RD
1.5 kW
CS
+
DUT
VHBM
-
100 pF
Figure 5. HBM ESD Test Circuit
1.5
VHBM = 2 kV
DUT = 10-V, 1-W Zener Diode
|
1.0
0.5
0.0
0
50
100
150
200
Time - ns
Figure 6. Typical HBM Current Waveform
Machine Model (MM)
The MM ESD test applies to all pins using a 200-pF capacitor with no discharge resistance. The purpose of the
MM test is to simulate possible ESD conditions that can occur during the handling and assembly processes of
manufacturing. In this case, ESD protection is required for all pins, not just RS-232 pins. However, after PC
board assembly, the MM test no longer is as pertinent to the RS-232 pins.
8
Submit Documentation Feedback
PACKAGE OPTION ADDENDUM
www.ti.com
10-Jun-2014
PACKAGING INFORMATION
Orderable Device
MAX202CD
Status Package Type Package Pins Package
Eco Plan
Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
0 to 70
Device Marking
Samples
Drawing
Qty
(1)
(2)
(6)
(3)
(4/5)
ACTIVE
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
TSSOP
TSSOP
TSSOP
SOIC
SOIC
SOIC
SOIC
SOIC
D
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
MAX202C
MAX202CDG4
MAX202CDR
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
D
D
40
2500
2500
40
Green (RoHS
& no Sb/Br)
0 to 70
MAX202C
MAX202C
MAX202C
MAX202C
MAX202C
MAX202C
MAX202C
MAX202C
MA202C
Green (RoHS
& no Sb/Br)
0 to 70
MAX202CDRE4
MAX202CDW
MAX202CDWE4
MAX202CDWG4
MAX202CDWR
MAX202CDWRE4
MAX202CPW
MAX202CPWG4
MAX202CPWR
MAX202ID
D
Green (RoHS
& no Sb/Br)
0 to 70
DW
DW
DW
DW
DW
PW
PW
PW
D
Green (RoHS
& no Sb/Br)
0 to 70
40
Green (RoHS
& no Sb/Br)
0 to 70
40
Green (RoHS
& no Sb/Br)
0 to 70
2000
2000
90
Green (RoHS
& no Sb/Br)
0 to 70
Green (RoHS
& no Sb/Br)
0 to 70
Green (RoHS
& no Sb/Br)
0 to 70
90
Green (RoHS
& no Sb/Br)
0 to 70
MA202C
2000
40
Green (RoHS
& no Sb/Br)
0 to 70
MA202C
Green (RoHS
& no Sb/Br)
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
MAX202I
MAX202I
MAX202I
MAX202I
MAX202I
MAX202IDE4
MAX202IDG4
MAX202IDR
D
40
Green (RoHS
& no Sb/Br)
D
40
Green (RoHS
& no Sb/Br)
D
2500
2500
Green (RoHS
& no Sb/Br)
MAX202IDRE4
D
Green (RoHS
& no Sb/Br)
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Jun-2014
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
Device Marking
Samples
Drawing
Qty
(1)
(2)
(6)
(3)
(4/5)
MAX202IDRG4
MAX202IDW
ACTIVE
SOIC
SOIC
D
16
16
16
16
16
16
16
16
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
MAX202I
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
DW
DW
DW
PW
PW
PW
PW
40
40
Green (RoHS
& no Sb/Br)
MAX202I
MAX202I
MAX202I
MB202I
MB202I
MB202I
MB202I
MAX202IDWG4
MAX202IDWR
MAX202IPW
SOIC
Green (RoHS
& no Sb/Br)
SOIC
2000
90
Green (RoHS
& no Sb/Br)
TSSOP
TSSOP
TSSOP
TSSOP
Green (RoHS
& no Sb/Br)
MAX202IPWG4
MAX202IPWR
MAX202IPWRE4
90
Green (RoHS
& no Sb/Br)
2000
2000
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
10-Jun-2014
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
MAX202CDR
MAX202CDWR
MAX202CPWR
MAX202IDR
SOIC
SOIC
D
16
16
16
16
16
16
2500
2000
2000
2500
2000
2000
330.0
330.0
330.0
330.0
330.0
330.0
16.4
16.4
12.4
16.4
16.4
12.4
6.5
10.3
2.1
2.7
1.6
2.1
2.7
1.6
8.0
12.0
8.0
16.0
16.0
12.0
16.0
16.0
12.0
Q1
Q1
Q1
Q1
Q1
Q1
DW
PW
D
10.75 10.7
TSSOP
SOIC
6.9
6.5
5.6
10.3
8.0
MAX202IDWR
MAX202IPWR
SOIC
DW
PW
10.75 10.7
6.9 5.6
12.0
8.0
TSSOP
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
MAX202CDR
MAX202CDWR
MAX202CPWR
MAX202IDR
SOIC
SOIC
D
16
16
16
16
16
16
2500
2000
2000
2500
2000
2000
333.2
367.0
367.0
333.2
367.0
367.0
345.9
367.0
367.0
345.9
367.0
367.0
28.6
38.0
35.0
28.6
38.0
35.0
DW
PW
D
TSSOP
SOIC
MAX202IDWR
MAX202IPWR
SOIC
DW
PW
TSSOP
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated
相关型号：
MAX2031
High-Linearity, 815MHz to 1000MHz Upconversion/ Downconversion Mixer with LO Buffer/Switch
MAXIM
©2020 ICPDF网 联系我们和版权申明