LT1013DDRE4 [TI]
DUAL PRECISION OPERATIONAL AMPLIFIERS; 双精密运算放大器
| 型号： | LT1013DDRE4 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | DUAL PRECISION OPERATIONAL AMPLIFIERS |
| 文件： | 总33页 (文件大小：595K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
ꢀꢁ ꢂ ꢃ ꢂꢄ ꢅ ꢀꢁ ꢂ ꢃ ꢂꢄ ꢆꢅ ꢀꢁꢂ ꢃꢂ ꢄꢇ
ꢇꢈꢆ ꢀ ꢉꢊꢋ ꢌꢍꢎ ꢍꢏ ꢐ ꢏ ꢉꢋꢊ ꢆꢁ ꢍꢏ ꢐꢆꢀ ꢆꢑ ꢉ ꢀꢍ ꢒꢍ ꢋꢊ ꢎ
SLOS018H − MAY 1988 − REVISED NOVEMBER 2004
LT1013, LT1013D . . . D PACKAGE
(TOP VIEW)
D
Single-Supply Operation
− Input Voltage Range Extends to Ground
− Output Swings to Ground While Sinking
Current
1
2
3
4
8
7
6
5
1IN+
1IN−
1OUT
V
CC−
D
D
D
D
D
D
D
Input Offset Voltage
− 150 µV Max at 25°C for LT1013A
Offset-Voltage Temperature Coefficient
− 2.5 µV/°C Max for LT1013A
Input Offset Current
− 0.8 nA Max at 25°C for LT1013A
2IN+
2IN−
V
CC+
2OUT
LT1013, LT1013A . . . FK PACKAGE
(TOP VIEW)
High Gain . . . 1.5 V/µV Min (R = 2 kΩ),
L
0.8 V/µV Min (R = 600 kΩ) for LT1013A
L
3
2
1
20 19
18
NC
NC
4
5
6
7
8
Low Supply Current . . . 0.5 mA Max at
2OUT
NC
1IN−
NC
17
16
15
14
T = 25°C for LT1013A
A
Low Peak-to-Peak Noise Voltage . . . 0.55 µV
Typ
2IN−
NC
1IN+
NC
Low Current Noise . . . 0.07 pA/√Hz Typ
9 10 11 12 13
description/ordering information
The LT1013 devices are dual precision
operational amplifiers, featuring high gain, low
supply current, low noise, and low-offset-voltage
temperature coefficient.
NC − No internal connection
LT1013, LT1013D . . . JG OR P PACKAGE
(TOP VIEW)
The LT1013 devices can be operated from a
single 5-V power supply; the common-mode input
voltage range includes ground, and the output can
also swing to within a few millivolts of ground.
Crossover distortion is eliminated. The LT1013
can be operated with both dual 15-V and single
5-V supplies.
1OUT
1IN−
1IN+
V
CC+
1
2
3
4
8
7
6
5
2OUT
2IN−
2IN+
V
CC−
The LT1013C, LT1013AC, and LT1013D are characterized for operation from 0°C to 70°C. The LT1013I,
LT1013AI, and LT1013DI are characterized for operation from −40°C to 105°C. The LT1013M, LT1013AM, and
LT1013DM are characterized for operation over the full military temperature range of −55°C to 125°C.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
ꢉ
ꢉ
ꢊ
ꢏ
ꢢ
ꢇ
ꢝ
ꢙ
ꢈ
ꢌ
ꢛ
ꢁ
ꢜ
ꢦ
ꢍ
ꢖ
ꢏ
ꢔ
ꢗ
ꢐ
ꢕ
ꢇ
ꢆ
ꢁ
ꢆ
ꢓ
ꢔ
ꢞ
ꢝ
ꢕ
ꢖ
ꢜ
ꢜ
ꢗ
ꢘ
ꢙ
ꢙ
ꢔ
ꢚ
ꢚ
ꢓ
ꢓ
ꢟ
ꢖ
ꢖ
ꢗ
ꢔ
ꢔ
ꢖ
ꢓ
ꢛ
ꢛ
ꢟ
ꢛ
ꢜ
ꢝ
ꢗ
ꢗ
ꢞ
ꢞ
ꢔ
ꢚ
ꢙ
ꢘ
ꢛ
ꢛ
ꢛ
ꢔ
ꢖ
ꢕ
ꢟ
ꢝ
ꢠ
ꢛ
ꢛ
ꢡ
ꢓ
ꢜ
ꢙ
ꢛ
ꢚ
ꢓ
ꢚ
ꢧ
ꢖ
ꢗ
ꢔ
ꢝ
ꢢ
ꢙ
ꢔ
ꢢ
ꢚ
ꢚ
ꢞ
ꢛ
ꢞ
ꢣ
Copyright 2004, Texas Instruments Incorporated
ꢏ ꢔ ꢟ ꢗ ꢖꢢ ꢝꢜ ꢚꢛ ꢜꢖ ꢘꢟ ꢡꢓ ꢙꢔ ꢚ ꢚꢖ ꢑꢍ ꢀꢩ ꢉꢊ ꢒ ꢩꢄꢪꢫ ꢄꢫꢅ ꢙꢡꢡ ꢟꢙ ꢗ ꢙ ꢘꢞ ꢚꢞꢗ ꢛ ꢙ ꢗ ꢞ ꢚꢞ ꢛꢚꢞ ꢢ
ꢗ
ꢖ
ꢜ
ꢚ
ꢖ
ꢗ
ꢘ
ꢚ
ꢖ
ꢛ
ꢟ
ꢓ
ꢕ
ꢓ
ꢜ
ꢞ
ꢗ
ꢚ
ꢤ
ꢚ
ꢞ
ꢗ
ꢖ
ꢕ
ꢁ
ꢞ
ꢥ
ꢙ
ꢍ
ꢔ
ꢘ
ꢞ
ꢛ
ꢚ
ꢙ
ꢔ
ꢢ
ꢗ
ꢢ
ꢙ
ꢚ ꢞ ꢛ ꢚꢓ ꢔꢨ ꢖꢕ ꢙ ꢡꢡ ꢟꢙ ꢗ ꢙ ꢘ ꢞ ꢚ ꢞ ꢗ ꢛ ꢣ
ꢗ
ꢙ
ꢔ
ꢚ
ꢧ
ꢣ
ꢉ
ꢗ
ꢖ
ꢢ
ꢚ
ꢓ
ꢖ
ꢜ
ꢞ
ꢛ
ꢓ
ꢔ
ꢨ
ꢢ
ꢖ
ꢞ
ꢖ
ꢚ
ꢔ
ꢞ
ꢜ
ꢞ
ꢛ
ꢙ
ꢗ
ꢓ
ꢡ
ꢓ
ꢔ
ꢜ
ꢡ
ꢝ
ꢝ ꢔꢡ ꢞꢛꢛ ꢖ ꢚꢤꢞ ꢗ ꢦꢓ ꢛꢞ ꢔ ꢖꢚꢞ ꢢꢣ ꢏ ꢔ ꢙꢡ ꢡ ꢖ ꢚꢤꢞ ꢗ ꢟꢗ ꢖ ꢢꢝꢜ ꢚꢛ ꢅ ꢟꢗ ꢖ ꢢꢝꢜ ꢚꢓꢖ ꢔ
ꢚ
ꢟ
ꢗ
ꢖ
ꢜ
ꢞ
ꢛ
ꢛ
ꢓ
ꢔ
ꢨ
ꢢ
ꢖ
ꢞ
ꢛ
ꢔ
ꢖ
ꢚ
ꢔ
ꢞ
ꢜ
ꢞ
ꢛ
ꢛ
ꢙ
ꢗ
ꢓ
ꢡ
ꢧ
ꢓ
ꢔ
ꢜ
ꢡ
ꢝ
ꢢ
ꢞ
ꢚ
ꢞ
ꢛ
ꢓ
ꢔ
ꢨ
ꢖ
ꢕ
ꢙ
ꢡ
ꢡ
ꢟ
ꢙ
ꢗ
ꢙ
ꢘ
ꢞ
ꢚ
ꢞ
ꢗ
ꢛ
ꢣ
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀꢁ ꢂꢃ ꢂꢄ ꢅ ꢀꢁ ꢂ ꢃꢂ ꢄꢆ ꢅ ꢀꢁꢂ ꢃ ꢂ ꢄ ꢇ
ꢊ
ꢇ
ꢈ
ꢆ
ꢀ
ꢉ
ꢋ
ꢌ
ꢍ
ꢎ
ꢍ
ꢏ
ꢐ
ꢏ
ꢉ
ꢋ
ꢊ
ꢆ
ꢁ
ꢍ
ꢏ
ꢐ
ꢆ
ꢀ
ꢆ
ꢑ
ꢉ
ꢀꢍ
ꢒ
ꢍ
ꢋ
ꢊ
ꢎ
SLOS018H − MAY 1988 − REVISED NOVEMBER 2004
ORDERING INFORMATION
V
max
IO
ORDERABLE
PART NUMBER
TOP-SIDE
MARKING
†
PACKAGE
T
A
AT 25°C
(µV)
P−DIP (P)
Tube of 50
Tube of 75
LT1013CP
LT1013CD
LT1013P
300
800
800
SOIC (D)
P−DIP (P)
1013C
Reel of 2500 LT1013CDR
0°C to 70°C
Tube of 50
Tube of 75
LT1013DP
LT1013DD
LT1013DP
SOIC (D)
P−DIP (P)
1013D
Reel of 2500 LT1013DDR
Tube of 50
Tube of 75
LT1013DIP
LT1013DID
LT1013DIP
−40°C to 105°C
SOIC (D)
1013DI
Reel of 2500 LT1013DIDR
C−DIP (JG)
C−DIP (JGB)
LCCC (FK)
LCCC (FKB)
C−DIP (JG)
C−DIP (JGB)
LCCC (FKB)
SOIC (D)
Tube of 50
Tube of 50
Tube of 55
Tube of 55
Tube of 50
Tube of 50
Tube of 55
Tube of 75
LT1013AMJG
LT1013AMJGB
LT1013AMFK
LT1013AMFKB
LT1013MJG
LT1013AMJG
LT1013AMJGB
LT1013AMFK
LT1013AMFKB
LT1013MJG
LT1013MJGB
LT1013MFKB
1013DM
150
−55°C to 125°C
LT1013MJGB
LT1013MFKB
LT1013DMD
300
800
†
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are
available at www.ti.com/sc/package.
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀꢁ ꢂ ꢃ ꢂꢄ ꢅ ꢬꢀꢁ ꢂ ꢃ ꢂꢄ ꢆ ꢅ ꢬꢀꢁꢂ ꢃꢂ ꢄꢇ
ꢇꢈꢆ ꢀꢬꢉ ꢊꢋꢌ ꢍꢎꢍ ꢏꢐ ꢬꢏ ꢉꢋ ꢊꢆꢁ ꢍꢏ ꢐꢆꢀꢬꢆꢑꢉ ꢀꢍ ꢒ ꢍꢋ ꢊꢎ
SLOS018H − MAY 1988 − REVISED NOVEMBER 2004
•
3
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
ꢀꢁ ꢂꢃ ꢂꢄ ꢅ ꢀꢁ ꢂ ꢃꢂ ꢄꢆ ꢅ ꢀꢁꢂ ꢃ ꢂ ꢄ ꢇ
ꢇ ꢈꢆꢀ ꢉꢊ ꢋꢌ ꢍ ꢎꢍ ꢏꢐ ꢏ ꢉꢋ ꢊꢆꢁꢍ ꢏ ꢐꢆ ꢀ ꢆꢑ ꢉ ꢀꢍ ꢒ ꢍꢋꢊꢎ
SLOS018H − MAY 1988 − REVISED NOVEMBER 2004
†
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage (see Note 1): V
V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −22 V
CC+
CC−
Input voltage range, V (any input, see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V
− 5 V to V
I
CC−
CC+
Differential input voltage (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 V
Duration of short-circuit current at (or below) 25°C (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unlimited
Package thermal impedance, θ (see Notes 4 and 5): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97°C/W
JA
P package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85°C/W
Operating virtual junction temperature, T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
J
Case temperature for 60 seconds: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: JG package . . . . . . . . . . . . . . . . . . . . 300°C
Storage temperature range, T
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
stg
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between V
2. Differential voltages are at IN+ with respect to IN−.
and V .
CC−
CC+
3. The output may be shorted to either supply.
4. Maximum power dissipation is a function of T (max), θ , and T . The maximum allowable power dissipation at any allowable
J
JA
A
ambient temperature is P = (T (max) − T )/θ . Operating at the absolute maximum T of 150°C can affect reliability. Due to
D
J
A
JA
J
variation in individual device electrical characteristics and thermal resistance, the built-in thermal overload protection may be
activated at power levels slightly above or below the rated dissipation.
5. The package thermal impedance is calculated in accordance with JESD 51-7.
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀꢁ ꢂ ꢃ ꢂꢄ ꢅ ꢬꢀꢁ ꢂ ꢃ ꢂꢄ ꢆ ꢅ ꢬꢀꢁꢂ ꢃꢂ ꢄꢇ
ꢇꢈꢆ ꢀꢬꢉ ꢊꢋꢌ ꢍꢎꢍ ꢏꢐ ꢬꢏ ꢉꢋ ꢊꢆꢁ ꢍꢏ ꢐꢆꢀꢬꢆꢑꢉ ꢀꢍ ꢒ ꢍꢋ ꢊꢎ
SLOS018H − MAY 1988 − REVISED NOVEMBER 2004
•
5
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
Template Release Date: 7−11−94
ꢀꢁ ꢂ ꢃꢂ ꢄ ꢅꢬ ꢀꢁ ꢂ ꢃꢂ ꢄ ꢆꢅ ꢬ ꢀꢁꢂ ꢃ ꢂ ꢄ ꢇ
ꢈ ꢆ ꢀꢬ ꢉꢊ ꢋꢌ ꢍ ꢎꢍ ꢏꢐꢬ ꢏ ꢉ ꢋꢊ ꢆꢁꢍ ꢏ ꢐꢆ ꢀꢬꢆꢑ ꢉꢀ ꢍꢒ ꢍꢋ ꢊꢎ
ꢇ
SLOS018H − MAY 1988 − REVISED NOVEMBER 2004
6
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
ꢀꢁ ꢂ ꢃ ꢂꢄ ꢅ ꢬꢀꢁ ꢂ ꢃ ꢂꢄ ꢆ ꢅ ꢬꢀꢁꢂ ꢃꢂ ꢄꢇ
ꢇꢈꢆ ꢀꢬꢉ ꢊꢋꢌ ꢍꢎꢍ ꢏꢐ ꢬꢏ ꢉꢋ ꢊꢆꢁ ꢍꢏ ꢐꢆꢀꢬꢆꢑꢉ ꢀꢍ ꢒ ꢍꢋ ꢊꢎ
SLOS018H − MAY 1988 − REVISED NOVEMBER 2004
•
7
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
Template Release Date: 7−11−94
ꢀꢁ ꢂ ꢃꢂ ꢄ ꢅꢬ ꢀꢁ ꢂ ꢃꢂ ꢄ ꢆꢅ ꢬ ꢀꢁꢂ ꢃ ꢂ ꢄ ꢇ
ꢈ ꢆ ꢀꢬ ꢉꢊ ꢋꢌ ꢍ ꢎꢍ ꢏꢐꢬ ꢏ ꢉ ꢋꢊ ꢆꢁꢍ ꢏ ꢐꢆ ꢀꢬꢆꢑ ꢉꢀ ꢍꢒ ꢍꢋ ꢊꢎ
ꢇ
SLOS018H − MAY 1988 − REVISED NOVEMBER 2004
8
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
ꢀꢁ ꢂ ꢃ ꢂꢄ ꢅ ꢬꢀꢁ ꢂ ꢃ ꢂꢄ ꢆ ꢅ ꢬꢀꢁꢂ ꢃꢂ ꢄꢇ
ꢇꢈꢆ ꢀꢬꢉ ꢊꢋꢌ ꢍꢎꢍ ꢏꢐ ꢬꢏ ꢉꢋ ꢊꢆꢁ ꢍꢏ ꢐꢆꢀꢬꢆꢑꢉ ꢀꢍ ꢒ ꢍꢋ ꢊꢎ
SLOS018H − MAY 1988 − REVISED NOVEMBER 2004
•
9
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
Template Release Date: 7−11−94
ꢀꢁ ꢂ ꢃꢂ ꢄ ꢅꢬ ꢀꢁ ꢂ ꢃꢂ ꢄ ꢆꢅ ꢬ ꢀꢁꢂ ꢃ ꢂ ꢄ ꢇ
ꢈ ꢆ ꢀꢬ ꢉꢊ ꢋꢌ ꢍ ꢎꢍ ꢏꢐꢬ ꢏ ꢉ ꢋꢊ ꢆꢁꢍ ꢏ ꢐꢆ ꢀꢬꢆꢑ ꢉꢀ ꢍꢒ ꢍꢋ ꢊꢎ
ꢇ
SLOS018H − MAY 1988 − REVISED NOVEMBER 2004
10
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
ꢀꢁ ꢂ ꢃ ꢂꢄ ꢅ ꢀꢁ ꢂ ꢃ ꢂꢄ ꢆꢅ ꢀꢁꢂ ꢃꢂ ꢄꢇ
ꢇꢈꢆ ꢀ ꢉꢊꢋ ꢌꢍꢎ ꢍꢏ ꢐ ꢏ ꢉꢋꢊ ꢆꢁ ꢍꢏ ꢐꢆꢀ ꢆꢑ ꢉ ꢀꢍ ꢒꢍ ꢋꢊ ꢎ
SLOS018H − MAY 1988 − REVISED NOVEMBER 2004
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
vs Supply voltage
1
2
3
4
5
V
Input offset voltage
IO
vs Temperature
vs Time
∆V
IO
Change in input offset voltage
Input offset current
I
IO
I
IB
vs Temperature
vs Temperature
Input bias current
V
Common-mode input voltage
vs Input bias current
vs Load resistance
vs Frequency
vs Frequency
vs Temperature
vs Frequency
vs Frequency
vs Temperature
vs Time
6
7, 8
9, 10
11
IC
A
VD
Differential voltage amplification
Channel separation
Output saturation voltage
12
CMRR Common-mode rejection ratio
13
k
Supply-voltage rejection ratio
Supply current
14
SVR
I
I
15
CC
Short-circuit output current
Equivalent input noise voltage
Equivalent input noise current
Peak-to-peak input noise voltage
16
OS
V
n
vs Frequency
vs Frequency
vs Time
17
I
n
17
V
18
N(PP)
Small signal
19, 21
20, 22, 23
9
Pulse response
Phase shift
Large signal
vs Frequency
11
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀꢁ ꢂꢃ ꢂꢄ ꢅ ꢀꢁ ꢂ ꢃꢂ ꢄꢆ ꢅ ꢀꢁꢂ ꢃ ꢂ ꢄ ꢇ
ꢇ ꢈꢆꢀ ꢉꢊ ꢋꢌ ꢍ ꢎꢍ ꢏꢐ ꢏ ꢉꢋ ꢊꢆꢁꢍ ꢏ ꢐꢆ ꢀ ꢆꢑ ꢉ ꢀꢍ ꢒ ꢍꢋꢊꢎ
SLOS018H − MAY 1988 − REVISED NOVEMBER 2004
†
TYPICAL CHARACTERISTICS
INPUT OFFSET VOLTAGE
INPUT OFFSET VOLTAGE
vs
OF REPRESENTATIVE UNITS
vs
SUPPLY VOLTAGE
FREE-AIR TEMPERATURE
10
250
200
150
100
50
V
CC
= 15 V
V
T
A
= 5 V, V
= −55°C to 125°C
= 0
CC+
CC−
V
T
=
15 V
CC
A
= −55°C to 125°C
1
V
V
T
A
= 5 V
= 0
= 25°C
CC+
CC−
0
−50
−100
−150
0.1
R
S
−
+
V
T
A
=
15V
−200
−250
CC
= 25°C
R
S
0.01
1 k
3 k 10 k 30 k 100 k 300 k 1 M 3 M 10 M
|V | − Supply Voltage − V
−50
−25
0
25
50
75
100
125
T
A
− Free-Air Temperature − °C
CC
Figure 1
Figure 2
WARM-UP CHANGE
IN INPUT OFFSET VOLTAGE
vs
INPUT OFFSET CURRENT
vs
TIME AFTER POWER-ON
FREE-AIR TEMPERATURE
1
5
4
V
IC
= 0
V
T
A
=
15 V
CC
= 25°C
0.8
0.6
0.4
0.2
3
2
1
V
= 2.5 V
CC
V
CC+
= 5 V, V
CC−
= 0
JG Package
V
CC
= 15 V
0
−50
0
0
25
50
75
100
125
−25
0
1
2
3
4
5
T
A
− Free-Air Temperature − °C
t − Time After Power-On − min
Figure 3
Figure 4
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
12
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀꢁ ꢂ ꢃ ꢂꢄ ꢅ ꢀꢁ ꢂ ꢃ ꢂꢄ ꢆꢅ ꢀꢁꢂ ꢃꢂ ꢄꢇ
ꢇꢈꢆ ꢀ ꢉꢊꢋ ꢌꢍꢎ ꢍꢏ ꢐ ꢏ ꢉꢋꢊ ꢆꢁ ꢍꢏ ꢐꢆꢀ ꢆꢑ ꢉ ꢀꢍ ꢒꢍ ꢋꢊ ꢎ
SLOS018H − MAY 1988 − REVISED NOVEMBER 2004
†
TYPICAL CHARACTERISTICS
INPUT BIAS CURRENT
vs
FREE-AIR TEMPERATURE
COMMON-MODE INPUT VOLTAGE
vs
INPUT BIAS CURRENT
−30
15
10
5
5
4
V
IC
= 0
T
= 25°C
A
−25
−20
−15
−10
−5
3
2
V
V
= 5 V
= 0
V
=
15 V
CC
CC−
CC
V
CC
= 5 V, V = 0
CC−
(left scale)
(right scale)
0
V
CC
= 2.5 V
1
0
−5
−10
−15
V
CC
= 15 V
−1
0
−50
−25
0
25
50
100
125
0
−5
−10
−15
−20
−25
−30
75
I
IB
− Input Bias Current − nA
T
A
− Free-Air Temperature − °C
Figure 5
Figure 6
DIFFERENTIAL VOLTAGE AMPLIFICATION
DIFFERENTIAL VOLTAGE AMPLIFICATION
vs
vs
LOAD RESISTANCE
LOAD RESISTANCE
10
4
10
4
V
V
=
10 V
15 V
CC
O
V
V
= 5 V, V
= 0
= 20 mV to 3.5 V
CC
O
CC−
=
T
A
= 25°C
T
A
= −55°C
T
A
= −55°C
1
1
T
A
= 25°C
T
A
= 125°C
T
A
= 125°C
0.4
0.4
0.1
100
0.1
100
400
1 k
4 k
10 k
400
1 k
4 k
10 k
R
− Load Resistance − Ω
R
− Load Resistance − Ω
L
L
Figure 7
Figure 8
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
13
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀꢁ ꢂꢃ ꢂꢄ ꢅ ꢀꢁ ꢂ ꢃꢂ ꢄꢆ ꢅ ꢀꢁꢂ ꢃ ꢂ ꢄ ꢇ
ꢇ ꢈꢆꢀ ꢉꢊ ꢋꢌ ꢍ ꢎꢍ ꢏꢐ ꢏ ꢉꢋ ꢊꢆꢁꢍ ꢏ ꢐꢆ ꢀ ꢆꢑ ꢉ ꢀꢍ ꢒ ꢍꢋꢊꢎ
SLOS018H − MAY 1988 − REVISED NOVEMBER 2004
†
TYPICAL CHARACTERISTICS
DIFFERENTIAL VOLTAGE AMPLIFICATION
AND PHASE SHIFT
vs
DIFFERENTIAL VOLTAGE AMPLIFICATION
vs
FREQUENCY
FREQUENCY
80°
25
20
140
120
V
C
T
A
= 0
= 100 pF
= 25°C
IC
L
C
T
= 100 pF
= 25°C
L
A
100°
120°
V
CC
=
15 V
15
10
5
100
80
Phase Shift
V
V
= 5 V
CC+
− = 0
V
CC
=
15 V
V
V
= 5 V
= 0
CC+
CC−
CC
140°
160°
180°
200°
AVD
60
V
V
= 5 V
CC+
CC−
40
20
0
−5
= 0
VCC
= 15 V
−10
−15
220°
240°
0
−20
0.01 0.1
1
10 100 1 k 10 k 100 k 1 M 10 M
f − Frequency − Hz
0.01
0.3
1
3
10
f − Frequency − MHz
Figure 9
Figure 10
OUTPUT SATURATION VOLTAGE
vs
CHANNEL SEPARATION
vs
FREE-AIR TEMPERATURE
FREQUENCY
10
160
140
120
V
CC+
V
CC−
= 5 V to 30 V
= 0
V
V
R
=
15 V
CC
= 20 V to 5 kHz
= 2 kΩ
I(PP)
L
T
A
= 25°C
Isink = 10 mA
1
Limited by
Thermal
Interaction
Isink = 5 mA
Isink = 1 mA
R
= 100 Ω
L
R
= 1 kΩ
L
100
80
Isink = 100 µA
0.1
Limited by
Pin-to-Pin
Capacitance
Isink = 10 µA
Isink = 0
60
0.01
10
100
1 k
10 k
100 k
1 M
−50
−25
0
25
50
75
100
125
T
A
− Free-Air Temperature − °C
f − Frequency − Hz
Figure 11
Figure 12
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
14
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀꢁ ꢂ ꢃ ꢂꢄ ꢅ ꢀꢁ ꢂ ꢃ ꢂꢄ ꢆꢅ ꢀꢁꢂ ꢃꢂ ꢄꢇ
ꢇꢈꢆ ꢀ ꢉꢊꢋ ꢌꢍꢎ ꢍꢏ ꢐ ꢏ ꢉꢋꢊ ꢆꢁ ꢍꢏ ꢐꢆꢀ ꢆꢑ ꢉ ꢀꢍ ꢒꢍ ꢋꢊ ꢎ
SLOS018H − MAY 1988 − REVISED NOVEMBER 2004
†
TYPICAL CHARACTERISTICS
COMMON-MODE REJECTION RATIO
SUPPLY-VOLTAGE REJECTION RATIO
vs
vs
FREQUENCY
FREQUENCY
140
120
100
80
120
100
80
T
= 25°C
A
V
T
A
= 15 V
= 25°C
CC
V
= 15 V
CC
V
= 5 V
CC+
Positive
Supply
V
= 0
CC−
Negative
Supply
60
60
40
40
20
0
20
0
10
0.1
1
10
100
1 k
10 k 100 k
1 M
100
1 k
10 k
100 k
1 M
f − Frequency − Hz
f − Frequency − Hz
Figure 13
Figure 14
SHORT-CIRCUIT OUTPUT CURRENT
SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
vs
ELAPSED TIME
40
460
420
380
340
300
V
CC+
= + 15 V
T
= −55°C
= 25°C
A
T
30
20
A
T
A
= 125°C
10
0
V
= + 15 V
CC+
T
= 125°C
A
−10
−20
−30
−40
T
= 25°C
A
T
= −55°C
A
V
CC+
= 5 V, V
25
= 0
CC−
260
0
1
2
3
0
50
75
100
125
−50
−25
t − Elapsed Time − min
T
A
− Free-Air Temperature − °C
Figure 15
Figure 16
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
15
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀꢁ ꢂꢃ ꢂꢄ ꢅ ꢀꢁ ꢂ ꢃꢂ ꢄꢆ ꢅ ꢀꢁꢂ ꢃ ꢂ ꢄ ꢇ
ꢇ ꢈꢆꢀ ꢉꢊ ꢋꢌ ꢍ ꢎꢍ ꢏꢐ ꢏ ꢉꢋ ꢊꢆꢁꢍ ꢏ ꢐꢆ ꢀ ꢆꢑ ꢉ ꢀꢍ ꢒ ꢍꢋꢊꢎ
SLOS018H − MAY 1988 − REVISED NOVEMBER 2004
TYPICAL CHARACTERISTICS
EQUIVALENT INPUT NOISE VOLTAGE
AND EQUIVALENT INPUT NOISE CURRENT
PEAK-TO-PEAK INPUT NOISE VOLTAGE
OVER A
vs
FREQUENCY
10-SECOND PERIOD
1000
2000
1600
1200
V
T
=
2 V to 18 V
V
=
2 V to 18 V
CC
A
CC
= 25°C
f = 0.1 Hz to 10 Hz
T
A
= 25°C
300
100
I
n
800
400
0
V
n
30
10
1/f Corner = 2 Hz
10
1
100
f − Frequency − Hz
1k
0
2
4
6
8
10
t − Time − s
Figure 17
Figure 18
VOLTAGE-FOLLOWER
SMALL-SIGNAL
PULSE RESPONSE
VOLTAGE-FOLLOWER
LARGE-SIGNAL
PULSE RESPONSE
80
60
40
20
0
20
15
V
= 15 V
CC
= 1
V
=
= 1
= 25°C
15 V
A
CC
V
A
A
T
= 25°C
V
A
T
10
5
0
−20
−40
−60
−80
−5
−10
−15
−20
0
2
4
6
8
10 12 14
0
50 100 150 200 250 300 350
t − Time − µs
t − Time − µs
Figure 19
Figure 20
16
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀꢁ ꢂ ꢃ ꢂꢄ ꢅ ꢀꢁ ꢂ ꢃ ꢂꢄ ꢆꢅ ꢀꢁꢂ ꢃꢂ ꢄꢇ
ꢇꢈꢆ ꢀ ꢉꢊꢋ ꢌꢍꢎ ꢍꢏ ꢐ ꢏ ꢉꢋꢊ ꢆꢁ ꢍꢏ ꢐꢆꢀ ꢆꢑ ꢉ ꢀꢍ ꢒꢍ ꢋꢊ ꢎ
SLOS018H − MAY 1988 − REVISED NOVEMBER 2004
TYPICAL CHARACTERISTICS
VOLTAGE-FOLLOWER
VOLTAGE-FOLLOWER
LARGE-SIGNAL
SMALL-SIGNAL
PULSE RESPONSE
PULSE RESPONSE
6
5
4
3
160
140
V
= 5 V, V
CC−
= 0
CC+
V = 0 to 4 V
V
= 5 V, V = 0
CC−
CC+
V = 0 to 100 mV
I
R
I
R
= 4.7 kΩ to 5 V
= 1
= 25°C
L
= 600 Ω to GND
= 1
= 25°C
L
A
V
A
A
V
A
120
100
80
60
40
20
0
T
T
2
1
0
−1
−2
−20
0
10 20 30 40 50 60 70
0
20 40 60 80 100 120 140
t − Time − µs
t − Time − µs
Figure 21
Figure 22
VOLTAGE-FOLLOWER
LARGE-SIGNAL
PULSE RESPONSE
6
5
4
3
2
1
0
V
= 5 V, V = 0
CC−
CC+
V = 0 to 4 V
I
R
= 0
= 1
= 25°C
L
A
V
A
T
−1
−2
0
10 20 30 40 50 60 70
t − Time − µs
Figure 23
17
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀꢁ ꢂꢃ ꢂꢄ ꢅ ꢀꢁ ꢂ ꢃꢂ ꢄꢆ ꢅ ꢀꢁꢂ ꢃ ꢂ ꢄ ꢇ
ꢇ ꢈꢆꢀ ꢉꢊ ꢋꢌ ꢍ ꢎꢍ ꢏꢐ ꢏ ꢉꢋ ꢊꢆꢁꢍ ꢏ ꢐꢆ ꢀ ꢆꢑ ꢉ ꢀꢍ ꢒ ꢍꢋꢊꢎ
SLOS018H − MAY 1988 − REVISED NOVEMBER 2004
APPLICATION INFORMATION
single-supply operation
The LT1013 is fully specified for single-supply operation (V
includes ground, and the output swings to within a few millivolts of ground.
= 0). The common-mode input voltage range
CC−
Furthermore, the LT1013 has specific circuitry that addresses the difficulties of single-supply operation, both
at the input and at the output. At the input, the driving signal can fall below 0 V, either inadvertently or on a
transient basis. If the input is more than a few hundred millivolts below ground, the LT1013 is designed to deal
with the following two problems that can occur:
1. On many other operational amplifiers, when the input is more than a diode drop below ground, unlimited
current flows from the substrate (V
terminal) to the input, which can destroy the unit. On the LT1013,
CC−
the 400-Ω resistors in series with the input [see schematic (each amplifier)] protect the device, even
when the input is 5 V below ground.
2. When the input is more than 400 mV below ground (at T = 25°C), the input stage of similar operational
A
amplifiers saturates, and phase reversal occurs at the output. This can cause lockup in servo systems.
Because of unique phase-reversal protection circuitry (Q21, Q22, Q27, and Q28), the LT1013 outputs
do not reverse, even when the inputs are at −1.5 V (see Figure 24).
This phase-reversal protection circuitry does not function when the other operational amplifier on the LT1013
is driven hard into negative saturation at the output. Phase-reversal protection does not work on amplifier 1
when amplifier 2 output is in negative saturation nor on amplifier 2 when amplifier 1 output is in negative
saturation.
At the output, other single-supply designs either cannot swing to within 600 mV of ground or cannot sink more
than a few microamperes while swinging to ground. The all-npn output stage of the LT1013 maintains its low
output resistance and high-gain characteristics until the output is saturated. In dual-supply operations, the
output stage is free of crossover distortion.
5
4
3
5
4
3
2
5
4
3
2
2
1
1
0
1
0
0
−1
−2
−1
−1
(a) V
I(PP)
= −1.5 V TO 4.5 V
(b) OUTPUT PHASE REVERSAL
EXHIBITED BY LM358
(c) NO PHASE REVERSAL
EXHIBITED BY LT1013
Figure 24. Voltage-Follower Response With Input Exceeding
the Negative Common-Mode Input Voltage Range
18
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀꢁ ꢂ ꢃ ꢂꢄ ꢅ ꢀꢁ ꢂ ꢃ ꢂꢄ ꢆꢅ ꢀꢁꢂ ꢃꢂ ꢄꢇ
ꢇꢈꢆ ꢀ ꢉꢊꢋ ꢌꢍꢎ ꢍꢏ ꢐ ꢏ ꢉꢋꢊ ꢆꢁ ꢍꢏ ꢐꢆꢀ ꢆꢑ ꢉ ꢀꢍ ꢒꢍ ꢋꢊ ꢎ
SLOS018H − MAY 1988 − REVISED NOVEMBER 2004
APPLICATION INFORMATION
comparator applications
The single-supply operation of the LT1013 is well suited for use as a precision comparator with TTL-compatible
output. In systems using both operational amplifiers and comparators, the LT1013 can perform multiple duties
(see Figures 25 and 26).
5
5
4
3
2
1
V
V
T
= 5 V
= 0
= 25°C
CC+
CC−
A
4
3
2
2 mV
10 mV
5 mV
5 mV
Overdrive
Overdrive
2 mV
10 mV
1
0
0
V
V
T
A
= 5 V
= 0
= 25°C
100 mV
100 mV
CC+
CC−
0
50 100 150 200 250 300 350 400 450
0
50 100 150 200 250 300 350 400 450
t − Time − µs
t − Time − µs
Figure 25. Low-to-High-Level Output
Response for Various Input Overdrives
Figure 26. High-to-Low-Level Output
Response for Various Input Overdrives
low-supply operation
The minimum supply voltage for proper operation of the LT1013 is 3.4 V (three NiCad batteries). Typical supply
current at this voltage is 290 µA; therefore, power dissipation is only 1 mW per amplifier.
offset voltage and noise testing
The test circuit for measuring input offset voltage and its temperature coefficient is shown in Figure 30. This
circuit, with supply voltages increased to 20 V, also is used as the burn-in configuration.
The peak-to-peak equivalent input noise voltage of the LT1013 is measured using the test circuit shown in
Figure 27. The frequency response of the noise tester indicates that the 0.1-Hz corner is defined by only one
zero. The test time to measure 0.1-Hz to 10-Hz noise should not exceed 10 seconds, as this time limit acts as
an additional zero to eliminate noise contribution from the frequency band below 0.1 Hz.
An input noise voltage test is recommended when measuring the noise of a large number of units. A 10-Hz input
noise voltage measurement correlates well with a 0.1-Hz peak-to-peak noise reading because both results are
determined by the white noise and the location of the 1/f corner frequency.
Current noise is measured by the circuit and formula shown in Figure 28. The noise of the source resistors is
subtracted.
19
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀꢁ ꢂꢃ ꢂꢄ ꢅ ꢀꢁ ꢂ ꢃꢂ ꢄꢆ ꢅ ꢀꢁꢂ ꢃ ꢂ ꢄ ꢇ
ꢇ ꢈꢆꢀ ꢉꢊ ꢋꢌ ꢍ ꢎꢍ ꢏꢐ ꢏ ꢉꢋ ꢊꢆꢁꢍ ꢏ ꢐꢆ ꢀ ꢆꢑ ꢉ ꢀꢍ ꢒ ꢍꢋꢊꢎ
SLOS018H − MAY 1988 − REVISED NOVEMBER 2004
APPLICATION INFORMATION
0.1 µF
100 kΩ
+
2 kΩ
10 Ω
+
LT1013
22 µF
4.3 kΩ
Oscilloscope
= 1 MΩ
LT1001
−
4.7 µF
R
in
−
2.2 µF
A
VD
= 50,000
100 kΩ
0.1 µF
110 kΩ
24.3 kΩ
NOTE A: All capacitor values are for nonpolarized capacitors only.
Figure 27. 0.1-Hz to 10-Hz Peak-to-Peak Noise Test Circuit
50 kΩ
(see Note A)
10 kΩ
†
†
†
10 MΩ
10 MΩ
15 V
+
+
100 Ω
LT1013
V
n
100 Ω
(see Note A)
V = 1000 V
O IO
−
LT1013
−
†
10 MΩ 10 MΩ
50 kΩ
(see Note A)
−15 V
2 1ń2
–(820 nV) ]
[V
2
no
I
+
n
40 MW 100
†
Metal-film resistor
NOTE A: Resistors must have low thermoelectric potential.
Figure 28. Noise-Current Test Circuit
and Formula
Figure 29. Test Circuit for V and aV
IO
IO
20
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀꢁ ꢂ ꢃ ꢂꢄ ꢅ ꢀꢁ ꢂ ꢃ ꢂꢄ ꢆꢅ ꢀꢁꢂ ꢃꢂ ꢄꢇ
ꢇꢈꢆ ꢀ ꢉꢊꢋ ꢌꢍꢎ ꢍꢏ ꢐ ꢏ ꢉꢋꢊ ꢆꢁ ꢍꢏ ꢐꢆꢀ ꢆꢑ ꢉ ꢀꢍ ꢒꢍ ꢋꢊ ꢎ
SLOS018H − MAY 1988 − REVISED NOVEMBER 2004
APPLICATION INFORMATION
typical applications
5 V
Q3
2N2905
820 Ω
Q1
2N2905
‡
T1
1N4002 (4)
+
+
68 Ω
SN74HC04 (6)
10 µF
10 µF
0.002 µF
Q2
2N2905
10 kΩ 10 kΩ
820 Ω
0.33 µF
5 V
1/2
Q4
2N2222
100 kΩ
†
10 kΩ
−
†
†
100 Ω
10 kΩ
20-mA Trim
†
LT1013
+
4 kΩ
2 kΩ
100 pF
1 kΩ
4-mA
Trim
†
10 kΩ
†
80 kΩ
−
4 mA to 20 mA
to Load
2.2 kΩ Max
4.3 kΩ
1/2
LT1013
+
5 V
LT1004
1.2 V
IN
0 to 4 V
†
‡
1% film resistor. Match 10-kΩ resistors to within 0.05%.
T1 = PICO-31080
Figure 30. 5-V 4-mA to 20-mA Current-Loop Transmitter With 12-Bit Accuracy
21
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀꢁ ꢂꢃ ꢂꢄ ꢅ ꢀꢁ ꢂ ꢃꢂ ꢄꢆ ꢅ ꢀꢁꢂ ꢃ ꢂ ꢄ ꢇ
ꢇ ꢈꢆꢀ ꢉꢊ ꢋꢌ ꢍ ꢎꢍ ꢏꢐ ꢏ ꢉꢋ ꢊꢆꢁꢍ ꢏ ꢐꢆ ꢀ ꢆꢑ ꢉ ꢀꢍ ꢒ ꢍꢋꢊꢎ
SLOS018H − MAY 1988 − REVISED NOVEMBER 2004
APPLICATION INFORMATION
T1
1N4002 (4)
0.1 Ω
+
5 V
+
100 kΩ
1/2
LT1013
−
10 µF
+
1/2
LT1013
−
To Inverter
Drive
†
68 kΩ
4 mA to 20 mA
Fully Floating
†
10 kΩ
4.3 kΩ
†
†
4 kΩ
301 Ω
5 V
1 kΩ
20-mA
Trim
2 kΩ
4-mA
Trim
LT1004
1.2 V
IN
0 to 4 V
†
1% film resistor
Figure 31. Fully Floating Modification to 4-mA to 20-mA Current-Loop Transmitter With 8-Bit Accuracy
5 V
1/2 LTC1043
6
5
5
6
8
+
1/2
IN+
IN−
7
OUT A
R2
1 µF
2
3
1 µF
LT1013
−
4
15
18
R1
1/2 LTC1043
7
3
8
+
IN+
IN−
1
1/2
LT1013
−
OUT B
1 µF
1 µF
11
12
2
R2
13
14
0.01 µF
R1
NOTE A: V = 150 µV, A
IO VD
= (R1/R2) + 1, CMRR = 120 dB, V = 0 to 5 V
ICR
Figure 32. 5-V Single-Supply Dual Instrumentation Amplifier
22
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀꢁ ꢂ ꢃ ꢂꢄ ꢅ ꢀꢁ ꢂ ꢃ ꢂꢄ ꢆꢅ ꢀꢁꢂ ꢃꢂ ꢄꢇ
ꢇꢈꢆ ꢀ ꢉꢊꢋ ꢌꢍꢎ ꢍꢏ ꢐ ꢏ ꢉꢋꢊ ꢆꢁ ꢍꢏ ꢐꢆꢀ ꢆꢑ ꢉ ꢀꢍ ꢒꢍ ꢋꢊ ꢎ
SLOS018H − MAY 1988 − REVISED NOVEMBER 2004
APPLICATION INFORMATION
10
+
To Input
Cable Shields
8
†
200 kΩ
LT1013
9
−
5 V
2
3
−
†
10 kΩ
1
‡
LT1013
20 kW
†
10 kΩ
IN−
+
5 V
10 kΩ
4
13
12
−
‡
RG (2 kΩ Typ)
14
LT1013
OUT
+
1 µF
11
200 kΩ
10 kΩ
6
‡
−
7
LT1013
20 kW
†
†
5
10 kΩ
10 kΩ
IN+
+
‡
5 V
†
‡
1% film resistor. Match 10-kΩ resistors to within 0.05%.
For high source impedances, use 2N2222 diodes.
NOTE A:
A
VD
= (400,000/RG) + 1
Figure 33. 5-V Precision Instrumentation Amplifier
23
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
22-Aug-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
LCCC
CDIP
LCCC
CDIP
LCCC
CDIP
CDIP
PDIP
SOIC
Drawing
5962-88760012A
5962-8876001PA
5962-88760022A
5962-8876002PA
LT1013AMFKB
LT1013AMJG
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
OBSOLETE
ACTIVE
FK
20
8
1
1
1
1
1
1
1
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
POST-PLATE N / A for Pkg Type
A42 SNPB N / A for Pkg Type
POST-PLATE N / A for Pkg Type
A42 SNPB N / A for Pkg Type
POST-PLATE N / A for Pkg Type
JG
FK
20
8
JG
FK
20
8
JG
A42 SNPB
A42 SNPB
Call TI
N / A for Pkg Type
N / A for Pkg Type
Call TI
LT1013AMJGB
LT1013AMP
JG
8
P
8
LT1013CD
D
8
75 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
LT1013CDE4
LT1013CDG4
LT1013CDR
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
SOIC
SOIC
SOIC
SOIC
SOIC
PDIP
PDIP
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
D
D
D
D
D
P
P
D
D
D
D
D
D
D
D
D
D
D
D
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
75 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
75 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
LT1013CDRE4
LT1013CDRG4
LT1013CP
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
50
Pb-Free
(RoHS)
CU NIPDAU N / A for Pkg Type
LT1013CPE4
LT1013DD
50
Pb-Free
(RoHS)
CU NIPDAU N / A for Pkg Type
75 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
LT1013DDE4
LT1013DDG4
LT1013DDR
75 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
75 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
LT1013DDRE4
LT1013DDRG4
LT1013DID
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
75 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
LT1013DIDE4
LT1013DIDG4
LT1013DIDR
LT1013DIDRE4
LT1013DIDRG4
75 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
75 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
22-Aug-2007
Orderable Device
LT1013DIP
Status (1)
ACTIVE
ACTIVE
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
Drawing
PDIP
P
8
50
50
75
Pb-Free
(RoHS)
CU NIPDAU N / A for Pkg Type
CU NIPDAU N / A for Pkg Type
CU NIPDAU Level-1-220C-UNLIM
LT1013DIPE4
PDIP
P
8
Pb-Free
(RoHS)
LT1013DMD
ACTIVE
ACTIVE
SOIC
SOIC
D
D
8
8
TBD
LT1013DMDG4
75 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
LT1013DP
ACTIVE
ACTIVE
PDIP
PDIP
P
P
8
8
50
Pb-Free
(RoHS)
CU NIPDAU N / A for Pkg Type
LT1013DPE4
50
Pb-Free
(RoHS)
CU NIPDAU N / A for Pkg Type
LT1013IP
LT1013MFKB
LT1013MJG
LT1013MJGB
LT1013MP
LT1013Y
OBSOLETE
ACTIVE
PDIP
LCCC
CDIP
CDIP
PDIP
P
FK
JG
JG
P
8
20
8
TBD
TBD
TBD
TBD
TBD
TBD
Call TI
Call TI
1
1
1
POST-PLATE N / A for Pkg Type
ACTIVE
A42 SNPB
A42 SNPB
Call TI
N / A for Pkg Type
N / A for Pkg Type
Call TI
ACTIVE
8
OBSOLETE
8
OBSOLETE XCEPT
Y
0
Call TI
Call TI
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Jun-2007
TAPE AND REEL INFORMATION
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Jun-2007
Device
Package Pins
Site
Reel
Reel
A0 (mm)
B0 (mm)
K0 (mm)
P1
W
Pin1
Diameter Width
(mm) (mm) Quadrant
(mm)
330
(mm)
12
LT1013CDR
LT1013DDR
LT1013DIDR
D
D
D
8
8
8
FMX
FMX
FMX
6.4
6.4
6.4
5.2
5.2
5.2
2.1
2.1
2.1
8
8
8
12
12
12
Q1
Q1
Q1
330
12
330
12
TAPE AND REEL BOX INFORMATION
Device
Package
Pins
Site
Length (mm) Width (mm) Height (mm)
LT1013CDR
LT1013DDR
LT1013DIDR
D
D
D
8
8
8
FMX
FMX
FMX
342.9
342.9
342.9
336.6
336.6
336.6
20.64
20.64
20.64
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Jun-2007
Pack Materials-Page 3
MECHANICAL DATA
MCER001A – JANUARY 1995 – REVISED JANUARY 1997
JG (R-GDIP-T8)
CERAMIC DUAL-IN-LINE
0.400 (10,16)
0.355 (9,00)
8
5
0.280 (7,11)
0.245 (6,22)
1
4
0.065 (1,65)
0.045 (1,14)
0.310 (7,87)
0.290 (7,37)
0.063 (1,60)
0.015 (0,38)
0.020 (0,51) MIN
0.200 (5,08) MAX
0.130 (3,30) MIN
Seating Plane
0.023 (0,58)
0.015 (0,38)
0°–15°
0.100 (2,54)
0.014 (0,36)
0.008 (0,20)
4040107/C 08/96
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a ceramic lid using glass frit.
D. Index point is provided on cap for terminal identification.
E. Falls within MIL STD 1835 GDIP1-T8
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL DATA
MLCC006B – OCTOBER 1996
FK (S-CQCC-N**)
LEADLESS CERAMIC CHIP CARRIER
28 TERMINAL SHOWN
A
B
NO. OF
TERMINALS
**
18 17 16 15 14 13 12
MIN
MAX
MIN
MAX
0.342
(8,69)
0.358
(9,09)
0.307
(7,80)
0.358
(9,09)
19
20
11
10
9
20
28
44
52
68
84
0.442
(11,23)
0.458
(11,63)
0.406
(10,31)
0.458
(11,63)
21
B SQ
22
0.640
(16,26)
0.660
(16,76)
0.495
(12,58)
0.560
(14,22)
8
A SQ
23
0.739
(18,78)
0.761
(19,32)
0.495
(12,58)
0.560
(14,22)
7
24
25
6
0.938
(23,83)
0.962
(24,43)
0.850
(21,6)
0.858
(21,8)
5
1.141
(28,99)
1.165
(29,59)
1.047
(26,6)
1.063
(27,0)
26 27 28
1
2
3
4
0.080 (2,03)
0.064 (1,63)
0.020 (0,51)
0.010 (0,25)
0.020 (0,51)
0.010 (0,25)
0.055 (1,40)
0.045 (1,14)
0.045 (1,14)
0.035 (0,89)
0.045 (1,14)
0.035 (0,89)
0.028 (0,71)
0.022 (0,54)
0.050 (1,27)
4040140/D 10/96
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a metal lid.
D. The terminals are gold plated.
E. Falls within JEDEC MS-004
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL DATA
MPDI001A – JANUARY 1995 – REVISED JUNE 1999
P (R-PDIP-T8)
PLASTIC DUAL-IN-LINE
0.400 (10,60)
0.355 (9,02)
8
5
0.260 (6,60)
0.240 (6,10)
1
4
0.070 (1,78) MAX
0.325 (8,26)
0.300 (7,62)
0.020 (0,51) MIN
0.015 (0,38)
Gage Plane
0.200 (5,08) MAX
Seating Plane
0.010 (0,25) NOM
0.125 (3,18) MIN
0.100 (2,54)
0.021 (0,53)
0.430 (10,92)
MAX
0.010 (0,25)
M
0.015 (0,38)
4040082/D 05/98
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001
For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties
may be subject to additional restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Applications
Audio
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/audio
Automotive
Broadband
Digital Control
Military
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/military
Interface
interface.ti.com
logic.ti.com
Logic
Power Mgmt
Microcontrollers
RFID
power.ti.com
Optical Networking
Security
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lpw
Telephony
Low Power
Wireless
Video & Imaging
Wireless
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated
相关型号：
LT1013DIDR
DUAL OP-AMP, 1000uV OFFSET-MAX, 1MHz BAND WIDTH, PDSO8, GREEN, PLASTIC, MS-012AA, SOIC-8
ROCHESTER
LT1013DIP
DUAL OP-AMP, 1000uV OFFSET-MAX, 1MHz BAND WIDTH, PDIP8, ROHS COMPLIANT, PLASTIC, DIP-8
ROCHESTER
©2020 ICPDF网 联系我们和版权申明