LMC555CM/NOPB [TI]
LMC555 CMOS Timer; LMC555 CMOS定时器型号: | LMC555CM/NOPB |
厂家: | TEXAS INSTRUMENTS |
描述: | LMC555 CMOS Timer |
文件: | 总21页 (文件大小:1138K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LMC555
www.ti.com
SNAS558J –FEBRUARY 2000–REVISED MARCH 2013
LMC555 CMOS Timer
Check for Samples: LMC555
1
FEATURES
DESCRIPTION
2
•
Less than 1 mW Typical Power Dissipation at
5V Supply
The LMC555 is a CMOS version of the industry
standard 555 series general purpose timers. In
addition to the standard package (SOIC, VSSSOP,
and PDIP) the LMC555 is also available in a chip
sized package (8 Bump DSBGA) using TI's DSBGA
package technology. The LMC555 offers the same
capability of generating accurate time delays and
frequencies as the LM555 but with much lower power
dissipation and supply current spikes. When operated
as a one-shot, the time delay is precisely controlled
by a single external resistor and capacitor. In the
stable mode the oscillation frequency and duty cycle
are accurately set by two external resistors and one
capacitor. The use of Texas Instruments' LMCMOS
process extends both the frequency range and low
supply capability.
•
•
•
3 MHz Astable Frequency Capability
1.5V Supply Operating Voltage Ensured
Output Fully Compatible with TTL and CMOS
Logic at 5V Supply
•
•
•
Tested to −10 mA, +50 mA Output Current
Levels
Reduced Supply Current Spikes During Output
Transitions
Extremely Low Reset, Trigger, and Threshold
Currents
•
•
Excellent Temperature Stability
Pin-for-Pin Compatible with 555 Series of
Timers
•
Available in 8-pin VSSOP Package and 8-Bump
DSBGA package
Pulse Width Modulator
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
2
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2000–2013, Texas Instruments Incorporated
LMC555
SNAS558J –FEBRUARY 2000–REVISED MARCH 2013
www.ti.com
Connection Diagram
Figure 1. 8-Pin SOIC, VSSOP, PDIP
Top View
Figure 2. 8-Bump DSBGA
Top View (Bump Side Down)
2
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LMC555
LMC555
www.ti.com
SNAS558J –FEBRUARY 2000–REVISED MARCH 2013
Table 1. Pin Descriptions
Package Pin Numbers
Pin Name
8-Pin SOIC, VSSOP, and PDIP
8-Bump DSBGA
GND
1
2
3
4
5
6
7
8
A3
B3
C3
C2
C1
B1
A1
A2
Trigger
Output
Reset
Control Voltage
Threshold
Discharge
V+
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings(1)(2)(3)
Supply Voltage, V+
15V
−0.3V to VS + 0.3V
15V
Input Voltages, VTRIG, VRES, VCTRL, VTHRESH
Output Voltages, VO, VDIS
Output Current IO, IDIS
100 mA
Storage Temperature Range
−65°C to +150°C
Soldering specification for PDIP package:
Soldering (10 seconds)
260°C
Soldering specification for all other packages:
see product folder at www.ti.com and http://www.ti.com/lit/SNOA549
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication
of device performance.
(2) See AN-1112 (SNVA009) for DSBGA considerations.
(3) If Military/Aerospace specified devices are required, please contact the TI Sales Office/Distributors for availability and specifications.
Operating Ratings(1)(2)
Temperature Range
LMC555IM
−40°C to +125°C
−40°C to +85°C
LMC555CM/MM/N/TP
Thermal Resistance (θJA
SOIC, 8-Pin
(1)
)
169°C/W
225°C/W
111°C/W
220°C/W
VSSOP, 8-Pin
PDIP, 8-Pin
8-Bump DSBGA
Maximum Allowable Power Dissipation @25°C
PDIP-8
1126 mW
740 mW
555 mW
568 mW
SOIC-8
VSSOP-8
8-Bump DSBGA
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication
of device performance.
(2) See AN-1112 (SNVA009) for DSBGA considerations.
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LMC555
LMC555
SNAS558J –FEBRUARY 2000–REVISED MARCH 2013
www.ti.com
Electrical Characteristics(1) (2)
Test Circuit, T = 25°C, all switches open, RESET to VS unless otherwise noted
Units
(Limits)
Parameter
Test Conditions
Min
Typ
Max
IS
Supply Current
VS = 1.5V
VS = 5V
VS = 12V
50
100
150
150
250
400
µA
VCTRL
Control Voltage
VS = 1.5V
VS = 5V
VS = 12V
0.8
2.9
7.4
1.0
3.3
8.0
1.2
3.8
8.6
V
mV
V
VDIS
VOL
Discharge Saturation Voltage
Output Voltage (Low)
VS = 1.5V, IDIS = 1 mA
VS = 5V, IDIS = 10 mA
75
150
150
300
VS = 1.5V, IO = 1 mA
VS = 5V, IO = 8 mA
VS = 12V, IO = 50 mA
0.2
0.3
1.0
0.4
0.6
2.0
VOH
Output Voltage
(High)
VS = 1.5V, IO = −0.25 mA
VS = 5V, IO = −2 mA
1.0
4.4
1.25
4.7
V
VS = 12V, IO = −10 mA
10.5
11.3
VTRIG
Trigger Voltage
VS = 1.5V
VS = 12V
0.4
3.7
0.5
4.0
0.6
4.3
V
pA
V
ITRIG
VRES
Trigger Current
Reset Voltage
VS = 5V
10
(3)
VS = 1.5V
0.4
0.4
0.7
0.75
1.0
1.1
VS = 12V
VS = 5V
VS = 5V
VS = 12V
IRES
ITHRESH
IDIS
Reset Current
10
10
pA
pA
nA
Threshold Current
Discharge Leakage
Timing Accuracy
1.0
100
t
SW 2, 4 Closed
VS = 1.5V
VS = 5V
0.9
1.0
1.0
1.1
1.1
1.1
1.25
1.20
1.25
ms
VS = 12V
Δt/ΔVS
Δt/ΔT
fA
Timing Shift with Supply
VS = 5V ± 1V
0.3
75
%/V
ppm/°C
kHz
Timing Shift with Temperature VS = 5V
Astable Frequency
SW 1, 3 Closed, VS = 12V
4.0
4.8
3.0
15
5.6
fMAX
tR, tF
Maximum Frequency
Max. Freq. Test Circuit, VS = 5V
MHz
ns
Output Rise and
Fall Times
Max. Freq. Test Circuit
VS = 5V, CL = 10 pF
tPD
Trigger Propagation Delay
VS = 5V, Measure Delay
from Trigger to Output
100
ns
(1) All voltages are measured with respect to the ground pin, unless otherwise specified.
(2) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication
of device performance.
(3) If the RESET pin is to be used at temperatures of −20°C and below VS is required to be 2.0V or greater.
4
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LMC555
LMC555
www.ti.com
SNAS558J –FEBRUARY 2000–REVISED MARCH 2013
For device pinout, please see Table 1.
Figure 3. Test Circuit
For device pinout, please see Table 1.
Figure 4. Maximum Frequency Test Circuit
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LMC555
LMC555
SNAS558J –FEBRUARY 2000–REVISED MARCH 2013
www.ti.com
APPLICATION INFORMATION
MONOSTABLE OPERATION
In this mode of operation, the timer functions as a one-shot (Figure 5). The external capacitor is initially held
discharged by internal circuitry. Upon application of a negative trigger pulse of less than 1/3 VS to the Trigger
terminal, the flip-flop is set which both releases the short circuit across the capacitor and drives the output high.
Figure 5. Monostable (One-Shot)
The voltage across the capacitor then increases exponentially for a period of tH = 1.1 RAC, which is also the time
that the output stays high, at the end of which time the voltage equals 2/3 VS. The comparator then resets the
flip-flop which in turn discharges the capacitor and drives the output to its low state. Figure 6 shows the
waveforms generated in this mode of operation. Since the charge and the threshold level of the comparator are
both directly proportional to supply voltage, the timing internal is independent of supply.
VCC = 5V
Top Trace: Input 5 V/Div.
TIME = 0.1 ms/Div. Middle Trace: Output 5 V/Div.
RA = 9.1 kΩ
Bottom Trace: Capacitor Voltage 2 V/Div.
C = 0.01 µF
Figure 6. Monostable Waveforms
Reset overrides Trigger, which can override threshold. Therefore the trigger pulse must be shorter than the
desired tH. The minimum pulse width for the Trigger is 20ns, and it is 400ns for the Reset. During the timing cycle
when the output is high, the further application of a trigger pulse will not effect the circuit so long as the trigger
input is returned high at least 10µs before the end of the timing interval. However the circuit can be reset during
this time by the application of a negative pulse to the reset terminal. The output will then remain in the low state
until a trigger pulse is again applied.
When the reset function is not use, it is recommended that it be connected to V+ to avoid any possibility of false
triggering. Figure 7 is a nomograph for easy determination of RC values for various time delays.
NOTE
In monstable operation, the trigger should be driven high before the end of timing cycle.
6
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LMC555
LMC555
www.ti.com
SNAS558J –FEBRUARY 2000–REVISED MARCH 2013
Figure 7. Time Delay
ASTABLE OPERATION
If the circuit is connected as shown in Figure 8 (Trigger and Threshold terminals connected together) it will
trigger itself and free run as a multivibrator. The external capacitor charges through RA + RB and discharges
through RB. Thus the duty cycle may be precisely set by the ratio of these two resistors.
Figure 8. Astable (Variable Duty Cycle Oscillator)
In this mode of operation, the capacitor charges and discharges between 1/3 VS and 2/3 VS. As in the triggered
mode, the charge and discharge times, and therefore the frequency are independent of the supply voltage.
Figure 9 shows the waveform generated in this mode of operation.
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LMC555
LMC555
SNAS558J –FEBRUARY 2000–REVISED MARCH 2013
www.ti.com
VCC = 5V
Top Trace: Output 5 V/Div.
Bottom Trace: Capacitor Voltage 1 V/Div.
TIME = 20 µs/Div.
RA = 3.9 kΩ
RB = 9 kΩ
C = 0.01 µF
Figure 9. Astable Waveforms
The charge time (output high) is given by
t1 = 0.693 (RA + RB)C
(1)
(2)
(3)
And the discharge time (output low) by:
t2 = 0.693 (RB)C
Thus the total period is:
T = t1 + t2 = 0.693 (RA + 2RB)C
The frequency of oscillation is:
(4)
Figure 10 may be used for quick determination of these RC Values. The duty cycle, as a fraction of total period
that the output is low, is:
(5)
Figure 10. Free Running Frequency
8
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LMC555
LMC555
www.ti.com
SNAS558J –FEBRUARY 2000–REVISED MARCH 2013
FREQUENCY DIVIDER
The monostable circuit of Figure 5 can be used as a frequency divider by adjusting the length of the timing cycle.
Figure 11 shows the waveforms generated in a divide by three circuit.
VCC = 5V
Top Trace: Input 4 V/Div.
TIME = 20 µs/Div. Middle Trace: Output 2 V/Div.
RA = 9.1 kΩ
Bottom Trace: Capacitor 2 V/Div.
C = 0.01 µF
Figure 11. Frequency Divider Waveforms
PULSE WIDTH MODULATOR
When the timer is connected in the monostable mode and triggered with a continuous pulse train, the output
pulse width can be modulated by a signal applied to the Control Voltage Terminal. Figure 12 shows the circuit,
and in Figure 13 are some waveform examples.
Figure 12. Pulse Width Modulator
VCC = 5V
Top Trace: Modulation 1 V/Div.
TIME = 0.2 ms/Div. Bottom Trace: Output Voltage 2 V/Div.
RA = 9.1 kΩ
C = 0.01 µF
Figure 13. Pulse Width Modulator Waveforms
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LMC555
LMC555
SNAS558J –FEBRUARY 2000–REVISED MARCH 2013
www.ti.com
PULSE POSITION MODULATOR
This application uses the timer connected for astable operation, as in Figure 14, with a modulating signal again
applied to the control voltage terminal. The pulse position varies with the modulating signal, since the threshold
voltage and hence the time delay is varied. Figure 15 shows the waveforms generated for a triangle wave
modulation signal.
Figure 14. Pulse Position Modulator
VCC = 5V
Top Trace: Modulation Input 1 V/Div.
Bottom Trace: Output Voltage 2 V/Div.
TIME = 0.1 ms/Div.
RA = 3.9 kΩ
RB = 3 kΩ
C = 0.01 µF
Figure 15. Pulse Position Modulator Waveforms
50% DUTY CYCLE OSCILLATOR
The frequency of oscillation is
f = 1/(1.4 RCC)
Figure 16. 50% Duty Cycle Oscillator
10
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LMC555
LMC555
www.ti.com
SNAS558J –FEBRUARY 2000–REVISED MARCH 2013
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: LMC555
LMC555
SNAS558J –FEBRUARY 2000–REVISED MARCH 2013
www.ti.com
REVISION HISTORY
Changes from Revision I (March 2013) to Revision J
Page
•
Changed layout of National Data Sheet to TI format .......................................................................................................... 10
12
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LMC555
PACKAGE OPTION ADDENDUM
www.ti.com
15-May-2013
PACKAGING INFORMATION
Orderable Device
LMC555CM
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 85
Top-Side Markings
Samples
Drawing
Qty
(1)
(2)
(3)
(4)
ACTIVE
SOIC
SOIC
D
8
8
95
TBD
Call TI
CU SN
Call TI
LMC
555CM
LMC555CM/NOPB
ACTIVE
D
95
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
-40 to 85
LMC
555CM
LMC555CMM
ACTIVE
ACTIVE
VSSOP
VSSOP
DGK
DGK
8
8
1000
1000
TBD
Call TI
CU SN
Call TI
-40 to 85
-40 to 85
ZC5
LMC555CMM/NOPB
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
ZC5
LMC555CMMX
ACTIVE
ACTIVE
VSSOP
VSSOP
DGK
DGK
8
8
3500
3500
TBD
Call TI
CU SN
Call TI
-40 to 85
-40 to 85
ZC5
ZC5
LMC555CMMX/NOPB
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
LMC555CMX
LMC555CMX/NOPB
LMC555CN
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
SOIC
SOIC
D
D
8
8
8
8
8
8
8
8
2500
2500
40
TBD
Call TI
CU SN
Call TI
Call TI
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
LMC
555CM
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
Call TI
LMC
555CM
PDIP
P
TBD
LMC
555CN
LMC555CN/NOPB
LMC555CTP/NOPB
LMC555CTPX/NOPB
LMC555IM/NOPB
LMC555IMX/NOPB
PDIP
P
40
Green (RoHS
& no Sb/Br)
Call TI
Level-1-NA-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Call TI
LMC
555CN
DSBGA
DSBGA
SOIC
YPB
YPB
D
250
3000
95
Green (RoHS
& no Sb/Br)
SNAGCU
SNAGCU
CU SN
Call TI
F
02
Green (RoHS
& no Sb/Br)
F
02
Green (RoHS
& no Sb/Br)
LMC
555IM
SOIC
D
2500
TBD
LMC
555IM
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
15-May-2013
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Mar-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LMC555CMM
LMC555CMM/NOPB
LMC555CMMX
VSSOP
VSSOP
VSSOP
VSSOP
SOIC
DGK
DGK
DGK
DGK
D
8
8
8
8
8
8
8
8
1000
1000
3500
3500
2500
2500
250
178.0
178.0
330.0
330.0
330.0
330.0
178.0
178.0
12.4
12.4
12.4
12.4
12.4
12.4
8.4
5.3
5.3
5.3
5.3
6.5
6.5
1.5
1.5
3.4
3.4
3.4
3.4
5.4
5.4
1.5
1.5
1.4
1.4
8.0
8.0
8.0
8.0
8.0
8.0
4.0
4.0
12.0
12.0
12.0
12.0
12.0
12.0
8.0
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
1.4
LMC555CMMX/NOPB
LMC555CMX
1.4
2.0
LMC555CMX/NOPB
LMC555CTP/NOPB
LMC555CTPX/NOPB
SOIC
D
2.0
DSBGA
DSBGA
YPB
YPB
0.66
0.66
3000
8.4
8.0
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Mar-2013
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LMC555CMM
LMC555CMM/NOPB
LMC555CMMX
VSSOP
VSSOP
VSSOP
VSSOP
SOIC
DGK
DGK
DGK
DGK
D
8
8
8
8
8
8
8
8
1000
1000
3500
3500
2500
2500
250
210.0
210.0
367.0
367.0
367.0
367.0
210.0
210.0
185.0
185.0
367.0
367.0
367.0
367.0
185.0
185.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
LMC555CMMX/NOPB
LMC555CMX
LMC555CMX/NOPB
LMC555CTP/NOPB
LMC555CTPX/NOPB
SOIC
D
DSBGA
DSBGA
YPB
YPB
3000
Pack Materials-Page 2
MECHANICAL DATA
YPB0008
D
0.5±0.045
E
TPA08XXX (Rev A)
D: Max = 1.464 mm, Min =1.403 mm
E: Max = 1.438 mm, Min =1.377 mm
4215100/A
12/12
A. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994.
B. This drawing is subject to change without notice.
NOTES:
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明