LM3253-C [TI]
用于 2G/3G/4G 功率放大器的高电流降压直流/直流转换器;
| 型号： | LM3253-C |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 用于 2G/3G/4G 功率放大器的高电流降压直流/直流转换器 放大器 功率放大器 转换器 |
| 文件： | 总26页 (文件大小：574K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LM3253
www.ti.com
SNVS791Q –FEBRUARY 2012–REVISED MAY 2013
LM3253 High-Current Step-Down Converter for 2G/3G/4G RF Power Amplifiers
Check for Samples: LM3253
1
FEATURES
2
•
High-Efficiency PFM and PWM Modes with
Internal Synchronous Rectification
DESCRIPTION
The LM3253 is a DC-DC converter optimized for
powering multi-mode 2G/3G/4G RF power amplifiers
(PAs) from a single Lithium-Ion cell. The LM3253
steps down an input voltage from 2.7V to 5.5V to a
dynamically adjustable output voltage of 0.4V to 3.6V.
The output voltage is set through a VCON analog
input that adjusts the output voltage to ensure
efficient operation at all power levels of the RF PA.
The LM3253 is optimized for USB datacard
applications.
•
•
Analog Bypass Function with Low Dropout
Resistance (45 mΩ typ.)
Dynamically Adjustable Output Voltage, 0.4V
to 3.6V (typ.), in PFM and PWM modes
•
•
•
3A Maximum Load Current in PWM Mode
2.7MHz (average) PWM Switching Frequency
Modulated Switching Frequency to Aid Rx
Band Compliance
The LM3253 operates in constant frequency Pulse
Width Modulation (PWM) mode producing a small
and predictable amount of output voltage ripple. This
enables best ECTEL power requirements in GMSK
and EDGE spectral compliance, with the minimal
amount of filtering and excess headroom. When
operating in Pulse Frequency Modulation (PFM)
mode, the LM3253 enables the lowest DG09 current
consumption and therefore maximizes system
efficiency.
•
Operates From a Single Li-ion Cell
(2.7V to 5.5V)
•
•
ACB Reduces Inductor Requirements and Size
Minimum Total Solution Size by Using Small
Footprint and Case Size Inductor and
Capacitors
•
•
16-bump Thin DSBGA Package
Current and Thermal Overload Protection
The LM3253 has a unique Active Current assist and
analog Bypass (ACB) feature to minimize inductor
size without any loss of output regulation for the
entire battery voltage and RF output power range,
until dropout. ACB provides a parallel current path,
when needed, to limit the maximum inductor current
to 1.84A (typ.) while still driving a 3A load. The ACB
also enables operation with minimal dropout voltage.
The LM3253 is available in a small 2 mm x 2 mm
chip-scale 16-bump DSBGA package.
APPLICATIONS
•
•
•
•
•
USB Datacards
Cellular Phones
Hand-Held Radios
RF PC Cards
Battery-Powered RF Devices
When considering the use of the LM3253 in a system
design, contact the Texas Instruments Sales or Field
Application engineer for a copy of the "LM3253:
DC-DC Converter for 3G/4G RF PAs PCB Layout
Considerations.”
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2012–2013, Texas Instruments Incorporated
LM3253
SNVS791Q –FEBRUARY 2012–REVISED MAY 2013
www.ti.com
Typical System Application Diagram
VBATT
10 µF
1.5 µH
VOUT
EN
PVIN VDD
LM3253
SW
BP
10 µF
GPO1
FB
VCC_PA_2G
4.7 µF
MODE
GPO2
DAC
ACB
VCON
BGND
PGND SGND
VCC_PA_3G
BB or
RFIC
PA
1.0 µF
PA(s)
Connection Diagram
A
B
C
D
A
B
C
D
PVIN
PVIN
BP
SW
PGND
PGND
SGND
PGND
PGND
SGND
SW
SW
EN
ACB
ACB
ACB
ACB
PVIN
PVIN
BP
SW
EN
BGND
BGND
MODE
VCON
VDD
VDD
VCON
FB
FB
MODE
1
2
3
4
4
3
2
1
Top View
Bottom View
Figure 1. 16-Bump 0.4 mm Pitch Thin DSBGA Package
2
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM3253
LM3253
www.ti.com
SNVS791Q –FEBRUARY 2012–REVISED MAY 2013
Pin Descriptions
Pin #
A1
Name
Description
PGND
Power Ground to the internal NFET switch.
B1
C1
SGND
VDD
Signal Analog and Control Ground (Low Current).
Analog Supply Input.
D1
A2
Switching Node connection to the internal PFET switch and NFET synchronous rectifier. Connect
to an inductor with a saturation current rating that exceeds the ILIM,PFET,Steady State Current Limit
specification of the LM3253.
SW
B2
C2
Enable Input. Set this digital input HIGH for normal operation. For shutdown, set low. Pin has an
800 kΩ internal pulldown resistor.
EN
D2
A3
B3
VCON
Voltage Control Analog input. VOUT = 2.5 x VCON.
PVIN
Power Supply Voltage Input to the internal PFET switch and ACB.
Bypass Mode Input. Set the pin HIGH for forced Bypass mode operation. Set the pin LOW for
automatic Analog Bypass Mode (recommended).
C3
D3
BP
PWM/PFM Mode Selection Input. Setting the pin HIGH allows for PFM or PWM, depending on
the load current. Setting the pin LOW forces the part to be in PWM only.
MODE
A4
B4
C4
D4
ACB
Analog Current Bypass. Connect to the output at the output filter capacitor.
BGND
FB
Active Current assist and analog Bypass Ground (High Current).
Feedback Analog Input. Connect to the output at the output filter capacitor.
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LM3253
LM3253
SNVS791Q –FEBRUARY 2012–REVISED MAY 2013
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ABSOLUTE MAXIMUM RATINGS(1)(2)(3)
VDD, PVIN to SGND
−0.2V to +6.0V
−0.2V to +0.2V
PGND to SGND
EN, FB, VCON, BP, MODE
SW, ACB
(SGND −0.2V) to (VDD +0.2V)
(PGND −0.2V) to (PVIN +0.2V
−0.2V to +0.2V
PVIN to VDD
Continuous Power Dissipation(4)
Internally Limited
Junction Temperature (TJ-MAX
Storage Temperature Range
)
+150°C
−65°C to +150°C
Maximum Lead Temperature
(Soldering, 10 sec)
ESD Rating(5)(6)
+260°C
2kV
Human Body Model
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltages are with respect to the potential at the GND pins. The LM3253 is designed for mobile phone applications where turn-on after
power-up is controlled by the system controller and where requirements for a small package size overrule increased die size for internal
Under Voltage Lock-Out (UVLO) circuitry. Thus, it should be kept in shutdown by holding the EN pin LOW until the input voltage
exceeds 2.7V.
(3) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
(4) Internal thermal shutdown circuitry protects the device from permanent damage. Thermal shutdown engages at TJ = 150°C (typ.) and
disengages at TJ = 130°C (typ.).
(5) The human body model is a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin. (MIL-STD-883 3015.7) The machine
model is a 200 pF capacitor discharged directly into each pin.
(6) Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper ESD
handling procedures can result in damage.
4
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM3253
LM3253
www.ti.com
SNVS791Q –FEBRUARY 2012–REVISED MAY 2013
OPERATING RATINGS(1)
Input Voltage Range
2.7V to 5.5V
0A to 3.0A
Recommended Load Current
Junction Temperature (TJ) Range
Ambient Temperature (TA) Range(2)
−30°C to +125°C
−30°C to +90°C
(1) All voltages are with respect to the potential at the GND pins. The LM3253 is designed for mobile phone applications where turn-on after
power-up is controlled by the system controller and where requirements for a small package size overrule increased die size for internal
Under Voltage Lock-Out (UVLO) circuitry. Thus, it should be kept in shutdown by holding the EN pin LOW until the input voltage
exceeds 2.7V.
(2) In applications where high-power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may
have to be de-rated. Maximum ambient temperature (TA-MAX) is dependent on the maximum operating junction temperature (TJ-MAX-OP
125°C), the maximum power dissipation of the device in the application (PD-MAX), and the junction-to ambient thermal resistance of the
=
part/package in the application (θJA), as given by the following equation: TA-MAX = TJ-MAX-OP – (θJA × PD-MAX). At higher power levels duty
cycle usage is assumed to drop (i.e., max power 12.5% usage is assumed) for 2G mode.
THERMAL PROPERTIES
Junction-to-Ambient Thermal
50°C/W
Resistance (θJA), YFQ Package(1)
(1) Junction-to-ambient thermal resistance (θJA) is taken from thermal modeling result, performed under the conditions and guidelines set
forth in the JEDEC standard JESD51-7.
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LM3253
LM3253
SNVS791Q –FEBRUARY 2012–REVISED MAY 2013
www.ti.com
ELECTRICAL CHARACTERISTICS(1)(2)(3)
Limits in standard typeface are for TA = TJ = 25°C. Limits in boldface type apply over the full operating ambient temperature
range (−30°C ≤ TA = TJ ≤ +90°C). Unless otherwise noted, all specifications apply to the Typical System Application Diagram
with: PVIN = VDD = EN = 3.8V, BP = 0V.
Symbol
VFB, LOW
VFB, HIGH
ISHDN
Parameter
Conditions
Min
Typ
Max
Units
Feedback voltage at low
setting
VCON = 0.16V, MODE = LOW(3)
0.3500
0.400
0.450
V
Feedback voltage at high
setting
VCON = 1.4V, VIN = 3.9V,
MODE = LOW(3)
EN = SW = VCON = 0V(4)
No switching(5)
MODE = HIGH
3.492
3.6
0.02
260
3.708
4
V
Shutdown supply current
µA
Iq_PFM
DC bias current into VDD
310
µA
(5)
No Switching
Iq_PWM
DC bias current into VDD
975
2.3
1100
2.5
MODE = LOW
Positive transient peak current
limit
ILIM,PFET, Transient
VCON = 0.6V(6)
A
A
ILIM,PFET,Steady
State
Positive steady state peak
current limit
VCON = 0.6V(6)
1.78
1.40
1.9
2.09
2.00
−1.31
2.97
Positive active current assist
peak current limit
VCON = 0.6V,
VACB = 2.8V(6)
ILIM, P_ACB
ILIM, NFET
FOSC
1.70
−1.50
2.70
A
NFET Switch negative peak
current limit
VCON = 1.0V(6)
−1.69
A
Average internal oscillator
frequency
VCON = 1.0V
2.43
1.2
MHz
VIH
Logic HIGH input threshold
Logic LOW input threshold
EN pin pulldown current
Pin input current
BP, EN, MODE
BP, EN, MODE
EN = 3.6V
V
VIL
0.5
10
1
IEN
0
5
IIN
BP, MODE
−1
−1
µA
IVCON
Gain
VCON pin leakage current
VCON to VOUT Gain
VCON = 1.0V
0.16V ≤ VCON ≤ 1.44V(6)
1
2.5
V/V
(1) All voltages are with respect to the potential at the GND pins. The LM3253 is designed for mobile phone applications where turn-on after
power-up is controlled by the system controller and where requirements for a small package size overrule increased die size for internal
Under Voltage Lock-Out (UVLO) circuitry. Thus, it should be kept in shutdown by holding the EN pin LOW until the input voltage
exceeds 2.7V.
(2) Min and Max limits are specified by design, test, or statistical analysis.
(3) The parameters in the electrical characteristics table are tested under open loop conditions at PVIN = VIN = 3.8V. For performance over
the input voltage range and closed-loop results, refer to the datasheet curves.
(4) Shutdown current includes leakage current of PFET.
(5) Iq specified here is when the part is not switching. For operating input current at no load, refer to datasheet curves.
(6) Current limit is built-in, fixed, and not adjustable.
6
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM3253
LM3253
www.ti.com
SNVS791Q –FEBRUARY 2012–REVISED MAY 2013
SYSTEM CHARACTERISTICS
The following spec table entries are specified by design and verifications providing the component values in the Typical
Application Circuit are used (L = 1.5 µH, DCR = 90 mΩ, TOKO DFE252010C (1269AS-H-1R5N), CIN = 10 µF, 6.3V, 0402,
Samsung CL05A106MQ5NUN, COUT = 10 µF + 4.7 µF + 3 x 1.0 µF + 3300 pF: 6.3V, 0402, Samsung CL05A106MQ5NUN,
CL05A475MQNRN; 6.3V, 0201 Samsung CL03A105MQ3CSN; 6.3V, 01005 Murata GRM022R60J332K).
These parameters are not verified by production testing. Min and Max values are specified over the ambient temperature
range TA = −30°C to 90°C. Typical values are specified at PVIN = VDD = EN = 3.8V, BP = 0V and TA = 25°C unless
otherwise stated.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
Time for SW pin to become
active upon power-up
tSETUP
EN = LOW-to-HIGH
30
Turn-on time (time for output
to reach 90% of final value
after EN LOW-to-HIGH
transition)
µs
EN = LOW-to-HIGH, VIN = 4.2V,
VCON = 1.36V, VOUT = 3.4V,
tON
50
20
IOUT ≤ 1 mA
VIN = 4.2V
RLOAD = 6.8Ω,
VCON = 0V to 1.2V
Time for VOUT to rise from 0V
to 3V (90% or 2.7V)
Time for VOUT to fall from
3.6V to 2.6V (10% or 2.7V)
VIN = 4.2V, RLOAD = 6.8Ω,
VCON = 1.44V to 1.04V
Time for VOUT to rise from
1.8V to 2.8V (90% or 2.7V)
VIN = 4.2V, RLOAD = 1.9Ω,
VCON = 0.72V to 1.12V
tRESPONSE
µs
15
20
Time for VOUT to fall from
2.8V to 1.8V (10% or 1.9V)
VIN = 4.2V, RLOAD = 1.9Ω,
VCON = 1.12V to 0.72V
Time for VOUT to rise from 0V VIN = 4.2V, RLOAD = 1.9Ω,
to 3.4V (90% or 3.1V)
VCON = 0V to 1.4V
Time for VOUT to fall from
3.4V to 0.4V (10% or 0.7V)
VIN = 4.2V, RLOAD = 1.9Ω,
VCON = 1.4V to 0.16V
Time for VOUT to rise from 0V
to PVIN after BP LOW-to-
HIGH transition (90%)
tBypass
VCON = 0V, IOUT ≤ 1mA
20
50
55
µs
Bypass turn-on time. Time for
VOUT to rise from 0V to PVIN
after EN LOW-to-HIGH
tBypass, ON
EN = VIN= 3.8V, IOUT ≤ 1 mA
transition (90% or 3.24)
VCON = 1.5V, Max value at
VIN = 3.1V,
Inductor ESR ≤ 151 mΩ
Total dropout resistance in
bypass mode
Rtot_drop
45
5
mΩ
Pin input capacitance for BP,
EN, MODE
CIN
Test frequency = 100 KHz
Switcher + ACB
pF
Maximum load current in
PWM mode
IOUT
3.0
3.4
Maximum output transient
pullup current limit
IOUT, PU
IOUT, PD, PWM
IOUT, MAX-PFM
A
Switcher + ACB(1)
PWM maximum output
transient pulldown current limit
−3.0
Maximum output load current VIN = 3.8V, VCON < 1V
in PFM mode
85
mA
MODE = HIGH(1)
−3
+3
%
Linearity in control range of
VCON = 0.16V to 1.44V
VIN = 4.2V(1)
Monotonic in nature
Linearity(2)
−50
+50
mV
(1) Current limit is built-in, fixed, and not adjustable.
(2) Linearity limits are ±3% or ±50 mV, whichever is larger.
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LM3253
LM3253
SNVS791Q –FEBRUARY 2012–REVISED MAY 2013
www.ti.com
SYSTEM CHARACTERISTICS (continued)
The following spec table entries are specified by design and verifications providing the component values in the Typical
Application Circuit are used (L = 1.5 µH, DCR = 90 mΩ, TOKO DFE252010C (1269AS-H-1R5N), CIN = 10 µF, 6.3V, 0402,
Samsung CL05A106MQ5NUN, COUT = 10 µF + 4.7 µF + 3 x 1.0 µF + 3300 pF: 6.3V, 0402, Samsung CL05A106MQ5NUN,
CL05A475MQNRN; 6.3V, 0201 Samsung CL03A105MQ3CSN; 6.3V, 01005 Murata GRM022R60J332K).
These parameters are not verified by production testing. Min and Max values are specified over the ambient temperature
range TA = −30°C to 90°C. Typical values are specified at PVIN = VDD = EN = 3.8V, BP = 0V and TA = 25°C unless
otherwise stated.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
VIN = 3.8V, VOUT = 1.8V,
IOUT = 10 mA
79
82
MODE = HIGH (PFM)
VIN = 3.8V, VOUT = 0.5V,
IOUT = 5 mA
MODE = HIGH (PFM)
58
89
90
83
81
60
92
93
86
84
1
VIN = 3.8V, VOUT = 3.5V,
IOUT = 1900 mA
MODE = LOW (PWM)
η
Efficiency
%
VIN = 3.8V, VOUT = 2.5V,
IOUT = 250 mA
MODE = LOW (PWM)
VIN = 3.8V, VOUT = 1.6V,
IOUT = 130 mA
MODE = LOW (PWM)
VIN = 3.8V, VOUT = 1V,
IOUT = 400 mA
MODE = LOW (PWM)
VIN = 3.4V to 3.6V, VOUT = 0.4V to
3.6V, ROUT = 1.9Ω(3)
Ripple voltage at no pulse
skipping condition
3
MODE = LOW
Ripple voltage at pulse
skipping condition
VIN = 5.5V to dropout, VOUT = 3.6V,
8
ROUT = 1.9Ω(3)
VRIPPLE
mVpp
mVpk
VIN = 3.2V, VOUT < 1.125V,
IOUT =10 mA, MODE = HIGH
50
50
PFM Ripple Voltage
VIN = 3.2V, VOUT ≤ 0.5V,
IOUT = 5 mA, MODE = LOW
VIN = 3.6V to 4.2V, TR = TF = 10 µs,
VOUT = 1V, IOUT = 600 mA
MODE = LOW
Line_tr
Line transient response
50
40
VOUT = 3.0V, TR = TF = 10 µs,
IOUT = 0A to 1.2A
MODE = LOW
Load_tr
Load transient response
Maximum duty cycle
mVpk
%
Max Duty cycle
MODE = LOW
100
100
VIN = 3.2V, VOUT = 1V, IOUT = 10 mA
MODE = HIGH
160
55
PFM_Freq
Minimum PFM Frequency
kHz
VIN = 3.2V, VOUT = 0.5V, IOUT = 5 mA
MODE = HIGH
34
(3) Ripple voltage should be measured at COUT electrode on a well-designed PC board and using the suggested inductor and capacitors.
8
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM3253
LM3253
www.ti.com
SNVS791Q –FEBRUARY 2012–REVISED MAY 2013
TYPICAL PERFORMANCE CHARACTERISTICS
Efficiency vs. Load Current
VIN = 3.8V, IOUT = 10mA to 150mA
Efficiency vs. Load Current
VIN = 3.8V, IOUT = 150mA to 750mA
100
95
90
85
80
75
70
65
60
100
95
90
85
80
75
70
65
60
VOUT = 1.0V
VOUT = 1.5V
VOUT = 2.0V
VOUT = 2.5V
VOUT = 3.0V
VOUT = 1.6V
VOUT = 2.0V
VOUT = 2.5V
VOUT = 3.0V
VOUT = 3.5V
0
20 40 60 80 100 120 140 160
LOAD CURRENT (mA)
Figure 2.
0
100 200 300 400 500 600 700 800
LOAD CURRENT (mA)
Figure 3.
Efficiency vs. Load Current
VIN = 3.8V, IOUT = 100mA to 1A
Efficiency vs. Load Current
VIN = 5V, IOUT = 1A to 2.5A
100
95
90
85
80
75
70
100
90
80
70
60
50
40
30
20
10
0
VOUT = 1.6V
VOUT = 2.0V
VOUT = 2.5V
VOUT = 3.0V
VOUT = 3.5V
VOUT = 2.0V
VOUT = 2.5V
VOUT = 3.0V
VOUT = 3.5V
0
200
400
600
800
1000
900 1200 1500 1800 2100 2400 2700
LOAD CURRENT (mA)
LOAD CURRENT (mA)
Figure 4.
Figure 5.
Output Voltage vs. Supply Voltage
VOUT = 3.4V, VIN = 4.3V down to dropout
3.6
Output Voltage vs. VCON Voltage
VIN = 4.2V, RLOAD = 6.8Ω, 0.16V < VCON < 1.4V
4.0
3.5
3.0
2.5
2.0
1.5
1.0
3.4
3.2
3.0
2.8
2.6
2.4
DROPOUT
2.5X GAIN
0.5
0.0
I
= 1.5A
OUT
2.5
3.0
3.5
4.0
4.5
5.0
5.5
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6
INPUT VOLTAGE (V)
VCON (V)
Figure 6.
Figure 7.
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LM3253
LM3253
SNVS791Q –FEBRUARY 2012–REVISED MAY 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Center-Switching Frequency vs. Supply Voltage
VOUT = 2.5V, IOUT = 700mA, VIN = 3.8V
3.00
Quiescent Current (PFM) vs. Supply Voltage
VOUT = 1V, 2.7V < VIN< 5.5V (No Load)
290
2.95
2.90
2.85
2.80
2.75
2.70
2.65
2.60
2.55
2.50
280
270
260
250
240
230
220
210
3.0 3.5 4.0 4.5 5.0 5.5 6.0
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
INPUT VOLTAGE (V)
INPUT VOLTAGE (V)
Figure 8.
Figure 9.
Quiescent Current (PWM) vs. Supply Voltage
VOUT = 2.5V, 2.7V < VIN< 5.5V (No Load)
VCON Transient (3G/4G)
VOUT = 0V to 3V, RLOAD = 6.8Ω, VIN = 3.8V
12
10
8
2V/DIV
2V/DIV
VOUT
VCON
IOUT
6
4
2
500 mA/DIV
0
20 ꢀs/DIV
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
INPUT VOLTAGE (V)
Figure 10.
Figure 11.
VCON Transient (2G)
VOUT = 1.4V to 3.4V, RLOAD = 1.9Ω, VIN = 4.2V
Load Transient in PFM Mode
VOUT = 1V, IOUT = 0mA to 60mA, VIN = 3.6V
VOUT
VCON
2V/DIV
VOUT
5 mV/DIV
2V/DIV
1A/DIV
IOUT
IOUT
50 mA/DIV
20 ꢀs/DIV
20 ꢀs/DIV
Figure 13.
Figure 12.
10
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM3253
LM3253
www.ti.com
SNVS791Q –FEBRUARY 2012–REVISED MAY 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Load Transient in PWM Mode
VIN = 3.8V, VOUT = 2.5V, IOUT = 0mA to 300mA
Load Transient in PWM Mode
VIN = 3.8V, VOUT = 3V, IOUT = 0mA to 700mA
20 mV/
DIV
50 mV/
DIV
VOUT
VOUT
500 mA/
DIV
200 mA/
DIV
IOUT
IOUT
100 ms/DIV
100 ms/DIV
Figure 14.
Figure 15.
Load Transient in PWM Mode
VIN = 4.2V, VOUT = 3V, IOUT = 0mA to 1.2A
Line Transient
VIN = 3.6V to 4.2V, VOUT = 2.5V, RLOAD = 6.8Ω
100 mV/
DIV
VOUT
VOUT
VIN
50 mV/DIV
1V/DIV
500 mA/
DIV
IOUT
100 ꢀs/DIV
100 ms/DIV
Figure 16.
Figure 17.
Line Transient
VIN = 3.6V to 4.2V, VOUT = 1V, RLOAD = 6.8Ω
Startup in PFM Mode
VIN = 3.8V, VOUT = 1V, No Load, EN = LOW to HIGH
2V/DIV
50 mV/DIV
VOUT
VSW
1V/DIV
2V/DIV
VOUT
EN
VIN
1V/DIV
100 ꢀs/DIV
20 ꢀs/DIV
Figure 18.
Figure 19.
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: LM3253
LM3253
SNVS791Q –FEBRUARY 2012–REVISED MAY 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Startup in PWM Mode
VIN = 4.2V, VOUT = 3.4V, No Load, EN = LOW to HIGH
Timed-Current Limit
VIN = 4.2V, VOUT = 2.5V, RLOAD = 6.8Ω to VOUT Shorted
VOUT
2V/DIV
2V/DIV
VSW
2V/DIV
2V/DIV
1A/DIV
VSW
VOUT
2V/DIV
Inductor
Current
EN
20 ꢀs/DIV
40 ꢀs/DIV
Figure 20.
Figure 21.
12
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM3253
LM3253
www.ti.com
SNVS791Q –FEBRUARY 2012–REVISED MAY 2013
OPERATION DESCRIPTION
Device Information
The LM3253 is a high-efficiency step-down DC-DC converter optimized to power the RF power amplifier (PA) in
cell phones, portable communication devices, or battery-powered RF devices with a single Li-Ion battery. It
operates in fixed-frequency PWM mode for 2G transmissions (with MODE = LOW), automatic mode transition
between PFM and PWM mode for 3G/4G RF PA operation (with MODE = HIGH), forced bypass mode (with BP
= HIGH) or in shutdown mode (with EN = LOW).
The fixed-frequency Pulse Width Modulation (PWM) mode provides high efficiency and very low output voltage
ripple. In Pulse Frequency Modulation (PFM) mode, the converter operates with reduced switching frequencies
and lower supply current to maintain high efficiencies. The forced bypass mode allows the user to drive the
output directly from the input supply through a bypass FET. The shutdown mode turns the LM3253 off and
reduces current consumption to 0.02 µA (typ.).
In PWM and PFM modes of operation, the output voltage of the LM3253 can be dynamically programmed from
0.4V to 3.6V (typ.) by adjusting the voltage on VCON. Current overload protection and thermal overload
protection are also provided.
The LM3253 was engineered with Active Current assist and analog Bypass (ACB). This unique feature allows
the converter to support maximum load currents of 3A (min.) while keeping a small footprint inductor and meeting
all of the transient behaviors required for operation of a multi-mode RF Power Amplifier. The ACB circuit provides
an additional current path when the load current exceeds 1.9A (typ.) or as the switcher approaches dropout.
Similarly, the ACB circuit allows the converter to respond with faster VCON output voltage transition times by
providing extra output current on rising and falling output edges. The ACB circuit also performs the function of
analog bypass. Depending upon the input voltage, output voltage and load current, the ACB circuit automatically
and seamlessly transitions the converter into analog bypass while maintaining output voltage regulation and low
output voltage ripple. Full bypass (100% duty cycle operation) will occur if the total dropout resistance in bypass
mode (Rtot_drop = 45 mΩ) is insufficient to regulate the output voltage.
The LM3253 16-bump DSBGA package is the best solution for space-constrained applications such as cell
phones and other hand-held devices. The high switching frequency, 2.7 MHz (typ.) in PWM mode, reduces the
size of input capacitors, output capacitors and of the inductor. Use of a DSBGA package is best suited for
opaque case applications and requires special design considerations for implementation. (Refer to DSBGA
Package Assembly And Use section below). As the LM3253 does not implement UVLO, the system controller
should set EN = LOW and set BP = HIGH during power-up and UVLO conditions. (Refer to Shutdown Mode
below).
PWM Operation
When the LM3253 operates in PWM mode, the switching frequency is constant, and the switcher regulates the
output voltage by changing the energy-per-cycle to support the load required. During the first portion of each
switching cycle, the control block in the LM3253 turns on the internal PFET switch. This allows current to flow
from the input through the inductor and to the output filter capacitor and load. The inductor limits the current to a
ramp with a slope of (VIN – VOUT)/L, by storing energy in its magnetic field.
During the second portion of each cycle, the control block turns the PFET switch off, blocking current flow from
the input, and then turns the NFET synchronous rectifier on. The inductor draws current from ground through the
NFET and to the output filter capacitor and load, which ramps the inductor current down with a slope of –VOUT/L.
The output filter capacitor stores charge when the inductor current is greater than the load current and releases it
when the inductor current is less than the load current, smoothing the voltage across the load.
At the next rising edge of the clock, the cycle repeats. An increase of load pulls the output voltage down,
increasing the error signal. As the error signal increases, the peak inductor current becomes higher, thus
increasing the average inductor current. The output voltage is therefore regulated by modulating the PFET switch
on-time to control the average current sent to the load. The circuit generates a duty-cycle modulated rectangular
signal that is averaged using a low pass filter formed by the inductor and output capacitor. The output voltage is
equal to the average of the duty-cycle modulated rectangular signal.
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: LM3253
LM3253
SNVS791Q –FEBRUARY 2012–REVISED MAY 2013
www.ti.com
PFM Mode
With MODE = HIGH, the LM3253 automatically transitions to from PWM into PFM operation if the average
inductor current is less than 75 mA (typ.) and VIN − VOUT > 0.6V. The switcher regulates the fixed output voltage
by transferring a fixed amount of energy during each cycle and modulating the frequency to control the total
power delivered to the output. The converter switches only as needed to support the demand of the load current,
therefore maximizing efficiency. If the load current should increase during PFM mode to more than 95 mA (typ.),
the part will automatically transition into constant frequency PWM mode. A 20 mA (typ.) hysteresis window exists
between PFM and PWM transitions.
After a transient event, the part temporarily operates in 2.7 MHz (typ.) fixed-frequency PWM mode to quickly
charge or discharge the output. This is true for start-up conditions or if MODE pin is toggled LOW-to-HIGH. Once
the output reaches its target output voltage, and the load is less than 75 mA (typ.), then the part will seamlessly
transition into PFM mode (assuming it is not in forced bypass or auto bypass condition).
Active Current Assist and Analog Bypass (ACB)
The 3GPP time mask requirement for 2G requires high current to be sourced by the LM3253. These high
currents are required for a small time during transients or under a heavy load. Over-rating the switching inductor
for these higher currents would increase the solution size and will not be an optimum solution. So to allow an
optimal inductor size for such a load, an alternate current path is provided from the input supply through the ACB
pin. Once the switcher current limit ILIM,PFET,SteadyState is reached, the ACB circuit starts providing the additional
current required to support the load. The ACB circuit also minimizes the dropout voltage by having the analog
bypass FET in parallel with VOUT. The LM3253 can provide up to 3A (min.) of current in bypass mode with a 4A
(max.) peak current limit.
Bypass Operation
The Bypass Circuit provides an analog bypass function with very low dropout resistance (Rtot_drop = 45 mΩ typ).
When BP = LOW the part will be in automatic bypass mode which will automatically determine the amount of
bypass needed to maintain voltage regulation. When the input supply voltage to the LM3253 is lowered to a level
where the commanded duty cycle is higher than what the converter is capable of providing, the part will go into
pulse-skipping mode. The switching frequency will be reduced to maintain a low and well-behaved output voltage
ripple. The analog bypass circuit will allow the converter to stay in regulation until full bypass is reached (100%
duty cycle operation). The converter comes out of full bypass and back into analog bypass regulation mode with
a similar reverse process.
To override the automatic bypass mode, either set VCON > (VIN)/(2.5) (but less than VIN) or set BP = HIGH for
forced bypass function. Forced bypass function is valid for 2.7V < VIN < 5.5V.
Shutdown Mode
To shut down the LM3253, pull the EN pin LOW (<0.5V). In shutdown mode, the current consumption is 0.02 µA
(typ.) and the PFET switch, NFET synchronous rectifier, reference voltage source, control and bias circuit are
turned OFF. To enable the LM3253 pull EN HIGH (>1.2V), and the mode of operation will be dependent on the
voltage applied to the MODE pin.
Since the LM3253 does not feature a UVLO (Under Voltage Lock-Out) circuit, the EN pin should be set LOW to
turn off the LM3253 during power-up and during UVLO conditions. For cell-phone applications, the system
controller determines the power supply sequence; thus, it is up to the system controller to ensure proper
sequencing by using all of the available pins and functions properly.
Mode Pin
The MODE pin changes the state of the converter to one of the two allowed modes of operation. Setting the
MODE pin HIGH (>1.2V) sets the device for automatic transition between PFM/PWM mode operation. In this
mode, the converter operates in PFM mode to maintain the output voltage regulation at very light loads and
transitions into PWM mode at loads exceeding 95 mA (typ.). The PWM switching frequency is 2.7 MHz (typ.).
Setting the MODE pin LOW (<0.5V) sets the device for PWM mode operation. The switching operation is in
PWM mode only, and the switching frequency is also 2.7 MHz (typ.).
14
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM3253
LM3253
www.ti.com
SNVS791Q –FEBRUARY 2012–REVISED MAY 2013
Dynamic Adjustment of Output Voltage
The output voltage of the LM3253 can be dynamically adjusted by changing the voltage on the VCON pin. In RF
PA applications, peak power is required when the handset is far away from the base station. To maximize the
power savings, the LM3253 output should be set just high enough to achieve the desired PA linearity. Hence,
during low-power requirements, reduction of supply voltage to the PA can reduce power consumption from the
PA, making the operation more efficient and promote longer battery life. Please refer to the Setting the Output
Voltage section for further details.
Mode Selection
Table 1 shows the LM3253 parameters for the given modes (PWM or PFM/PWM).
Table 1. Parameters under Different Modes
Parameter/Mode
MODE pin
PWM
LOW
LOW
PFM/PWM
HIGH
BP pin
LOW
Frequency at loads =
75 mA (typ.)
2.7 MHz (typ.)
Variable
Frequency at loads =
95 mA (typ.)
2.7 MHz (typ.)
2.5 x VCON
3 A (min.)
2.7 MHz (typ.)
2.5 x VCON
VOUT
75 mA (min in PFM) or 3.0A (min. in
PWM)
Max Load Steady State
Internal Synchronous Rectification
The LM3253 uses an internal NFET as a synchronous rectifier to reduce rectifier forward voltage drop, thus
increasing efficiency. The reduced forward voltage drop in the internal NFET synchronous rectifier significantly
improves efficiency for low output voltage operation. The NFET is designed to conduct through its intrinsic body
diode during the transient intervals, eliminating the need of an external diode.
Current Limit
The LM3253 current limit feature protects the converter during current overload conditions. Both SW and ACB
pins have positive and negative current limits. The positive and negative current limits bound the SW and ACB
currents in both directions. The SW pin has two positive current limits. The ILIM,PFET,SteadyState current limit triggers
the ACB circuit. Once the peak inductor current exceeds ILIM,PFET,SteadyState, the ACB circuit starts assisting the
switcher and provides just enough current to keep the inductor current from exceeding ILIM,PFET,SteadyState allowing
the switcher to operate at maximum efficiency. Transiently a second current limit ILIM,PFET,Transient of 2.3A (typ. or
2.5 max.) limits the maximum peak inductor current possible. The output voltage will fall out of regulation only
after both SW and ACB output pin currents reach their respective current limits of ILIM,PFET,Transient and ILIM,P-ACB
.
Timed Current Limit
If the load or output short circuit pulls the output voltage to 0.3V or lower, the LM3253 switches to a timed current
limit mode. In this mode the internal PFET switch is turned OFF after the current limit comparator trips, for 2~6
µsecs, to force the instantaneous inductor current to ramp down.
Thermal Overload Protection
The LM3253 IC has a thermal overload protection that protects itself from short-term misuse and overload
conditions. If the junction temperature exceeds 150°C, the LM3253 shuts down. Normal operation resumes after
the temperature drops below 130°C. Prolonged operation in thermal overload condition may damage the device
and is therefore not recommended.
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: LM3253
LM3253
SNVS791Q –FEBRUARY 2012–REVISED MAY 2013
www.ti.com
APPLICATION INFORMATION
Setting the Output Voltage
DAC Control
An analog voltage to the VCON pin can dynamically program the output voltage from 0.4V (typ.) to 3.6V (typ.) in
both PFM and PWM modes of operation, without the need for external resistors. The output voltage is governed
by Table 2.
Table 2. Output Voltage Selection
VCON (V)
VOUT (V)
VCON = 0.16V to 1.44V
2.5 x VCON
VIN
10 µF
PVIN
VDD
1.5 µH
SW
FB
VOUT
EN
GPIO
GPIO
LM3253
10 µF
4.7 µF
MODE
BP
ACB
VCON
DAC
SGND PGND
BGND
PDM Output
Figure 22. Dynamic Adjustment of Output Voltage with DAC or PDM
PDM-Based VCON Signal
Figure 22 shows the application circuit that enables the LM3253 to dynamically adjust the output voltage using a
GPIO pin from the system controller. Figure 23 shows the waveforms when adjusted dynamically. The PDM
signal of the GPIO is filtered using a low-pass filter and fed to the VCON pin. As the bitstream of the PDM signal
changes, the voltage on the VCON pin changes. Thus, the duty ratio on the GPIO pin can be used to
dynamically adjust the output voltage. The double low-pass filter reduces the ripple at VCON to avoid any
excessive VCON-induced ripple at the output voltage.
16
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM3253
LM3253
www.ti.com
SNVS791Q –FEBRUARY 2012–REVISED MAY 2013
EN
VCON
VCON = 0.4V
3.4V
8 30ms
8 30ms
3.4V
3.4V
V
1V
OUT
0V
7 20ms
1.7A
7 20ms
7 20ms
I
LOAD
< 200 mA
7 20ms
0A
Figure 23. Dynamic Adjustment of Output Voltage with GPIO
VCON Pin
Figure 24 shows the equivalent CRC circuit for the VCON pin. This circuit is internal to the part and should be
taken into consideration when driving this pin.
R1 = 100 kW
C2 = 9 pF
C1 = 1.7 pF
Figure 24. VCON Pin Equivalent CRC Circuit
Inductor Selection
A 1.5 µH inductor is needed for optimum performance and functionality of the LM3253. In the case of 2G
transmission current bursts, the effective overall RMS current requirements are reduced. Therefore, please
consult with the inductor manufacturers to determine if some of their smaller components will meet your
application needs even though the classical inductor specification does not appear to meet the LM3253 RMS
current specifications.
The LM3253 automatically manages the inductor peak and RMS (or steady current peak) current through the SW
pin. The SW pin has two positive current limits. The first is the 1.90A typical (or 2.09A max.) over-limit current
protection. It sets the upper steady-state inductor peak current (as detailed in the Electrical Characteristics Table
- ILIM,PFET,SteadyState). It is the dominant factor limiting the inductor's ISAT requirement. The second is a over-limit
current protection. It limits the maximum peak inductor current during large signal transients (i.e., < 20 µs) to
2.3A typical (or 2.5A maximum). A minimum inductance of 0.3 µH should be maintained at the second current
limit.
The ACB circuit automatically adjusts its output current to keep the steady-state inductor current below the
steady-state peak current limit. Thus, the inductor RMS current will effectively always be less than the
ILIM,PFET,SteadyState during the transmit burst. In addition, as in the case with 2G where the output current comes in
bursts, the effective overall RMS current would be much lower.
For good efficiency, the inductor’s resistance should be less than 0.2Ω; low DCR inductors (<0.2Ω) are
recommended. Table 3 suggests some inductors and suppliers.
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: LM3253
LM3253
SNVS791Q –FEBRUARY 2012–REVISED MAY 2013
www.ti.com
Table 3. Suggested Inductors and Their Suppliers
Model
DFE252010C (1269AS-H-1R5N)
TFM252010A-1R5M
Vendor
TOKO
TDK
Size
ISAT - 30%
2.7A
DCR
90 mΩ
80 mΩ
140 mΩ
2.5 mm x 2.0 mm x 1.0 mm
2.5 mm x 2.0 mm x 1.0 mm
2.0 mm x 1.6 mm x 1.0 mm
2.9A
TFM201610-1R5M
TDK
2.2A
Capacitor Selection
The LM3253 is designed to use ceramic capacitors for its input and output filters. Use a 10 µF capacitor for the
input and approximately 10 µF actual total output capacitance. Capacitor types such as X5R, X7R are
recommended for both filters. These provide an optimal balance between small size, cost, reliability and
performance for cell phones and similar applications. Table 4 lists suggested part numbers and suppliers. DC
bias characteristics of the capacitors must be considered while selecting the voltage rating and case size of the
capacitor. Smaller case sizes for the output capacitor mitigate piezo-electric vibrations of the capacitor when the
output voltage is stepped up and down at fast rates. However, they have a bigger percentage drop in value with
DC bias. For even smaller total solution size, 0402 case size capacitors are recommended for filtering. Use of
multiple 2.2 µF or 1 µF capacitors can also be considered. For RF Power Amplifier applications, split the output
capacitor between DC-DC converter and RF Power Amplifiers: 10 µF (COUT1) + 4.7 µF (COUT2) + 3 x 1 µF (COUT3
)
is recommended. The optimum capacitance split is application dependent, and for stability the actual total
capacitance (taking into account effects of capacitor DC bias, temperature de-rating, aging and other capacitor
tolerances) should target 10 µF with 2.5V DC bias (measured at 0.5 VRMS). Place all the output capacitors very
close to the respective device. A high-frequency capacitor (3300 pF) is highly recommended to be placed next to
COUT1
.
Table 4. Suggested Capacitors and Their Suppliers
Capacitance
10 µF
Model
Size (Wx L) (mm)
1.6 x 0.8
Vendor
Murata
GRM185R60J106M
CL05A106MQ5NUN
CL05A475MQ5NRN
CL03A105MQ3CSN
GRM022R60J332K
10 µF
1.0 x 0.5
Samsung
Samsung
Samsung
Murata
4.7 µF
1.0 x 0.5
1.0 µF
0.6 x 0.3
3300 pF
0.4 x 0.2
EN Input Control
Use the system controller to drive the EN HIGH or LOW with a comparator, Schmitt trigger or logic gate. Set EN
= HIGH (>1.2V) for normal operation and LOW (<0.5V) for shutdown mode to reduce current consumption to
0.02 µA (typ.) current.
Startup
The waveform Figure 25 in shows the startup condition. First, VIN should take on a value between 2.7V and 5.5V.
Next, EN should go HIGH (>1.2V). Finally, VCON should be set to a value that corresponds to the required
output voltage (VOUT = VCON x 2.5). VOUT will reach its steady-state value in less than 50 µs. To optimize the
startup time and behavior of the output voltage, the LM3253 will always start up in PWM mode (even when
MODE = HIGH and output load current ≤ 75mA), then seamlessly transition into PFM mode.
18
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM3253
LM3253
www.ti.com
SNVS791Q –FEBRUARY 2012–REVISED MAY 2013
VIN
EN
VCON
BP
8 30 µs
VOUT
720µs
Figure 25. Startup Sequence and Conditions
DSBGA Package Assembly And Use
Use of the DSBGA package requires specialized board layout, precision mounting and careful re-flow
techniques, as detailed in Texas Instruments Application Note AN-1112 (SNVA009). Refer to the section Surface
Mount Assembly Considerations. For best results in assembly, local alignment fiducials on the PC board should
be used to facilitate placement of the device.
The pad style used with DSBGA package must be the NSMD (non-solder mask defined) type. This means that
the solder-mask opening is larger than the pad size. This prevents a lip that would otherwise form if the solder-
mask and pad overlap, which would hold the device off the surface of the board and interfere with mounting. See
Application Note AN-1112 (SNVA009) for specific instructions how to do this.
The 16-bump package used for LM3253 has 265 micron solder balls and requires 0.225 mml pads for mounting
the circuit board. The trace to each pad should enter the pad with a 90°entry angle to prevent debris from being
caught in deep corners. Initially, the trace to each pad should be 5.6 mil wide, for a section approximately 5 mil
long, as a thermal relief. Then each trace should neck up or down to its optimal width. An important criterion is
symmetry to insure the solder bumps on the LM3253 re-flow evenly and that the device solders level to the
board. In particular, special attention must be paid to the pads for bumps A1, A3, B1, and B3 since PGND and
PVIN are typically connected to large copper planes, inadequate thermal reliefs can result in inadequate re-flow
of these bumps.
The DSBGA package is optimized for the smallest possible size in applications with red-opaque or infrared-
opaque cases. Because the DSBGA package lacks the plastic encapsulation characteristic of larger devices, it is
vulnerable to light. Backside metallization and/or epoxy coating, along with front-side shading by the printed
circuit board, reduce this sensitivity. However, the package has exposed die edges that are sensitive to light in
the red and infrared range shining on the package’s exposed die edges.
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: LM3253
LM3253
SNVS791Q –FEBRUARY 2012–REVISED MAY 2013
www.ti.com
Board Layout Considerations
PC board layout is an important part of DC-DC converter design. Please contact TI for detailed PCB layout
guidelines. Poor board layout can disrupt the performance of a DC-DC converter and surrounding circuitry by
contributing to EMI, ground bounce, and resistive voltage loss in the traces. These can send erroneous signals to
the DC-DC converter IC, resulting in poor regulation or instability. Poor layout can also result in re-flow problems
leading to poor solder joints between the DSBGA package and the board pads, which can result in erratic or
degraded performance. Good layout for the LM3253 can be implemented by following a few simple design rules.
1. Place the LM3253 on pads with a pad size of 0.225 mm and a solder mask opening of 0.325 mm. As a
thermal relief, connect to each pad to a trace that has maximally the same width as the solder mask opening
and incrementally increase each trace to its optimal width. Each board trace connecting to the solder mask
opening should be exactly the same width. This important criterion of symmetry is to insure that the solder
bumps on the LM3253 re-flow evenly (see AN-1112: Surface Mount Assembly Considerations) (SNVA009).
2. Place the LM3253, inductor and filter capacitors close together and make the trace short. The traces
between these components carry relatively high switching currents and act as antennas. Following this rule
reduces radiated noise. Place the capacitors and inductor within 0.3 mm of the LM3253.
3. Arrange the components so that the switching current loops curl in the same direction. During the first half of
each cycle, current flows from the input filter capacitor through the LM3253 and inductor to the output filter
capacitor and back through ground, forming a current loop. In the second half of each cycle, current is pulled
up from ground through the LM3253 by the inductor, to the output filter capacitor and then back through
ground, forming a second current loop. Routing these loops so the current curls in the same direction
prevents magnetic field reversal between the two half-cycles and reduces radiated noise.
4. Connect the ground pins of the LM3253 and filter capacitors together at a single-star connection using
generous component-side copper fill as a pseudo-ground plane. Then connect this to the ground-plane (if
one is used) with multiple vias in parallel. This reduces ground-plane noise by preventing the switching
currents from circulating through the ground plane. It also reduces ground bounce at the LM3253 by giving it
a low-impedance ground connection.
5. Use wide traces between the power components and for power connections to the DC-DC converter circuit.
This reduces voltage errors caused by resistive losses across the traces.
6. Route noise sensitive traces, such as the voltage feedback path, away from noisy traces between the power
components (such as SW trace to the inductor). The voltage feedback trace must remain close to the
LM3253 circuit and should be routed directly from FB to VOUT at the output capacitor and should be routed
opposite to noise components. This reduces EMI radiated onto the DC-DC converter’s own voltage feedback
trace.
7. Split up output capacitors between LM3253 output and PA(s). Suggestion is to place one-half of output
capacitance as close as possible to LM3253 output and the rest as close as possible to PA(s).
20
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM3253
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
LM3253TME/NOPB
LM3253TMX/NOPB
ACTIVE
ACTIVE
DSBGA
DSBGA
YFQ
YFQ
16
16
250
RoHS & Green
SNAGCU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-30 to 90
-30 to 90
S60
S60
3000 RoHS & Green
SNAGCU
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Aug-2022
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
K0
P1
W
B0
Reel
Diameter
Cavity
A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
Overall width of the carrier tape
W
P1 Pitch between successive cavity centers
Reel Width (W1)
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Sprocket Holes
Q1 Q2
Q3 Q4
Q1 Q2
Q3 Q4
User Direction of Feed
Pocket Quadrants
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LM3253TME/NOPB
LM3253TMX/NOPB
DSBGA
DSBGA
YFQ
YFQ
16
16
250
178.0
178.0
8.4
8.4
2.08
2.08
2.08
2.08
0.76
0.76
4.0
4.0
8.0
8.0
Q1
Q1
3000
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Aug-2022
TAPE AND REEL BOX DIMENSIONS
Width (mm)
H
W
L
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LM3253TME/NOPB
LM3253TMX/NOPB
DSBGA
DSBGA
YFQ
YFQ
16
16
250
208.0
208.0
191.0
191.0
35.0
35.0
3000
Pack Materials-Page 2
MECHANICAL DATA
YFQ0016x
D
0.600±0.075
E
TMD16XXX (Rev A)
D: Max = 2.049 mm, Min =1.989 mm
E: Max = 2.049 mm, Min =1.989 mm
4215081/A
12/12
A. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994.
B. This drawing is subject to change without notice.
NOTES:
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023, Texas Instruments Incorporated
©2020 ICPDF网 联系我们和版权申明